EPCOS B82802A0012A315 Smt flyback transformer Datasheet

SMT flyback transformers
EFD series
Series/Type:
B82802A
Date:
October 2012
Content of header bars 1 and 2 of data sheet will be automatically entered in headers and footers! Please fill in the
table and then change the color to "white". This ensures that the table disappears (invisible) for the customer PDF.
Don't change formatting when entering or pasting text in the table and don't add any cell or line in and to it!
Identification/Classification 1
(header 1 + top left bar):
SMT flyback transformers
Identification/Classification 2
(header 2 + bottom left header bar):
EFD series
Series/Type: (bottom right header bar)
B82802A
Preliminary data (optional):
(if necessary)
Department:
EPCOS Ho PD
Date:
October 2012
 EPCOS AG 2012. Reproduction, publication and dissemination of this publication, enclosures hereto and the information
contained therein without EPCOS' prior express consent is prohibited.
SMT flyback transformers
EFD series
B82802A
Construction
Dimensional drawing
 EFD type ferrite core
 10 gull wing terminals
 EFD15
Features
 Low profile SMT package with high
through-put power capability
 Industry standard footprints
 Compliant with JEDEC J-STD-020D
 MSL level 1
 RoHS compatible
 Custom variations available (on request)
Applications
 General purpose isolated DC/DC
converters (up to 55W)
 Power over Ethernet ( PoE/12W and PoE
+/30W) Powered Devices(PD) and Power
Sourcing Equipment (PSD)
 EFD20
Marking
 Manufacturer, middle block of ordering
code , date code, pin1 marker
Delivery mode and packing unit




44/56-mm blister tape , 330-mm Ø reel
Packing unit : 300 pcs./ reel (EFD15)
Packing unit : 160 pcs./ reel (EFD20)
Packing unit : 80 pcs./ reel (EFD25)
 EFD25
EPCOS Ho PD
Please read Cautions and warnings and
Important notes at the end of this document.
October 2012
Page 2 of 7
SMT flyback transformers
EFD series
B82802A
Schematic :
 Figure 1
Figure 2
 Figure 3
Figure 4
 Figure 5
Figure 6
EPCOS Ho PD
Please read Cautions and warnings and
Important notes at the end of this document.
October 2012
Page 3 of 7
SMT flyback transformers
EFD series
B82802A
Technical data and measuring conditions
Input voltage Vin
36 V DC … 60 V DC
Test voltage Vtest
1500 V AC
Main inductance L
100 kHz, 100 mV, +25 °C
Inductance tolerance
±10% at +25 °C
DC current IDC
With IDC bias Ldrop approx. 20%
Operating frequency f
100 kHz
DC resistance Rmax
Measured at +25 °C, maximum values (specified per winding)
Solderability
≥99.9 Sn or Sn96.5Ag3.0Cu0.5: +(245± 5) °C, (3±0.3) s
Wetting of soldering area: ≥95% (to IEC 60068-2-58)
Operating temperature range
–40°C … +125°C
Characteristics and ordering codes
Ordering code
Core
Schematic L
Lstray,max Turns ratio
DC resistance Rmax (Ω)
Pri
μH
μH
Sec
Vout1
Vout2 Vout3
B82802A0012A215
EFD15 Fig 1
100 3.0
(1-10):(2-9):(5-4)
1:2.25:6.5
0.03
0.19
0.45 -
B82802A0012A315
EFD15 Fig 2
100 3.0
(1-10):(2-9):(3-8):(5-4)
1:2.5:0.75:7.5
0.05
0.37
0.43 0.03
B82802A0030A220
EFD20 Fig 3
40
1.5
(1-10):(2-9):(5-4)
1:2.25:6.5
B82802A0030A320
EFD20 Fig 4
40
1.8
B82802A0055A225
EFD25 Fig 5
22
1.5
B82802A0055A325
EFD25 Fig 6
22
1.2
Ordering code
B82802A0012A215
B82802A0012A315
B82802A0030A220
B82802A0030A320
B82802A0055A225
B82802A0055A325
Core
EFD15
EFD15
EFD20
EFD20
EFD25
EFD25
Schematic
Fig 1
Fig 2
Fig 3
Fig 4
Fig 5
Fig 6
0.015 0.04
0.1
-
(1-10):(2-9):(3-8):(5-4) 1:2.25:0.75:6.5 0.018 0.04
0.1
0.01
(1-10):(2-9):(5,4-7)
0.003 0.04
(1-10):(2-9):(3-8):(5-4) 1:2.33:0.66:6.67 0.015 0.04
0.03 0.05 0.003
Power
Vout1
Vout2
Vout3
W
V/A
V/A
V/A
12
12
30
30
55
55
12/0.5
5.0/0.8
12/1.25
5.0/2.0
12/2.3
5.0/3.7
5.0/1.2
3.3/1.2
5.0/3.0
3.3/3.0
5.0/5.5
3.3/5.5
12/0.33
12/0.83
12/1.5
EPCOS Ho PD
Please read Cautions and warnings and
Important notes at the end of this document.
1:2.5:7.5
October 2012
Page 4 of 7
SMT flyback transformers
EFD series
B82802A
Taping and Packing
Item
DIM.
(mm)
Core
EFD15
EFD20
EFD25
Tolerance
Blister tape
W
T
44.0 0.5
44.0 0.6
56.0 0.6
±
0.3
±
0.05
A0
16.6
21.7
26.2
B0
22.3
26.6
33.0
P
24.0
32.0
44.0
K0
8.6
11.6
14.6
K1
8.1
10.6
13.8
Reel
F
Φ
40.4 330.0
40.4 330.0
52.4 330.0
±0.1
±0.1
±0.1
±0.1
±0.1
±0.1
±0.5
W1
44.0
44.0
56.0
W2
48.0
48.0
60.0
±2.0
±0.15
Blister tape
Reel
EPCOS Ho PD
Please read Cautions and warnings and
Important notes at the end of this document.
October 2012
Page 5 of 7
SMT flyback transformers
EFD series
B82802A
Cautions and warnings
■ Please note the recommendations in our Inductors data book (latest edition) and in the data
sheets.
– Particular attention should be paid to the derating curves given there.
– The soldering conditions should also be observed. Temperatures quoted in relation to wave
soldering refer to the pin, not the housing.
■ If the components are to be washed varnished it is necessary to check whether the washing
varnish agent that is used has a negative effect on the wire insulation, any plastics that are used,
or on glued joints. In particular, it is possible for washing varnish agent residues to have a
negative effect in the long-term on wire insulation
Washing processes may damage the product due to the possible static or cyclic mechanical
loads (e.g. ultrasonic cleaning). They may cause cracks to develop on the product and its parts,
which might lead to reduced reliability or lifetime.
■ The following points must be observed if the components are potted in customer applications:
– Many potting materials shrink as they harden. They therefore exert a pressure on the plastic
housing or core. This pressure can have a deleterious effect on electrical properties, and in
extreme cases can damage the core or plastic housing mechanically.
– It is necessary to check whether the potting material used attacks or destroys the wire
insulation, plastics or glue.
– The effect of the potting material can change the high-frequency behaviour of the components.
■ Ferrites are sensitive to direct impact. This can cause the core material to flake, or lead to
breakage of the core.
■ Even for customer-specific products, conclusive validation of the component in the circuit can
only be carried out by the customer..
EPCOS Ho PD
Please read Cautions and warnings and
Important notes at the end of this document.
October 2012
Page 6 of 7
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical
requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application. As a
rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them
than the customers themselves. For these reasons, it is always ultimately incumbent on the
customer to check and decide whether an EPCOS product with the properties described in the
product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or failure
before the end of their usual service life cannot be completely ruled out in the current state
of the art, even if they are operated as specified. In customer applications requiring a very high
level of operational safety and especially in customer applications in which the malfunction or
failure of an electronic component could endanger human life or health (e.g. in accident
prevention or life-saving systems), it must therefore be ensured by means of suitable design of the
customer application or other action taken by the customer (e.g. installation of protective circuitry
or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or
failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our Material
Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed
questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order.
We also reserve the right to discontinue production and delivery of products. Consequently,
we cannot guarantee that all products named in this publication will always be available.
The aforementioned does not apply in the case of individual agreements deviating from the
foregoing for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of
the “General Terms of Delivery for Products and Services in the Electrical Industry”
published by the German Electrical and Electronics Industry Association (ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CeraLink, CSMP, CSSP, CTVS, DeltaCap,
DigiSiMic, DSSP, FilterCap, FormFit, MiniBlue, MiniCell, MKD, MKK, MLSC, MotorCap, PCC,
PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD,
SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks
registered or pending in Europe and in other countries. Further information will be found on the
Internet at www.epcos.com/trademarks.
Page 7 of 7
Similar pages