Kingbright AA3528AVU/ASRS Single level surface mount cbi Datasheet

Single Level Surface Mount CBI
Part Number: AA3528AVU/ASRS
Super Bright Red
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
DISCHARGE
SENSITIVE
DEVICES
Features
Descriptions
z The Super Bright Red source color devices are made
z Surface mount type.
with Gallium Aluminum Arsenide Red Light Emitting
z Compatible with automatic placement equipment.
Diode.
z Compatible with infrared and vapor phase solder processes.
z Black case enhances contrast ratio.
z Housing material meets UL94V-0 flammability rating.
z Lens material meets UL94-HB flammability rating.
z Moisture sensitivity level : level 3.
z RoHS compliant.
z Electrostatic discharge and power surge could damage
the LEDs.
z It is recommended to use a wrist band or antielectrostatic glove when handling the LEDs.
z All devices, equipments and machineries must be
electrically grounded.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4.The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAN3492
REV NO: V.4B
DATE: SEP/22/2016
PAGE: 1 OF 7
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: W.Q.Zhong
ERP: 1102015728
Selection Guide
Part No.
Emitting Color (Material)
AA3528AVU/ASRS
Super Bright Red (GaAlAs)
Iv (mcd) [2]
@ 10mA
Lens Type
Viewing
Angle [1]
Min.
Typ.
2θ1/2
8
18
50°
Water Clear
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity / luminous Flux: +/-15%.
3. Luminous intensity value is traceable to CIE127-2007 standards.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Emitting Color
Typ.
λpeak
Peak Wavelength
Super Bright Red
λD [1]
Dominant Wavelength
Δλ1/2
Max.
Units
Test Conditions
655
nm
IF=10mA
Super Bright Red
640
nm
IF=10mA
Spectral Line Half-width
Super Bright Red
20
nm
IF=10mA
C
Capacitance
Super Bright Red
45
pF
VF=0V;f=1MHz
VF [2]
Forward Voltage
Super Bright Red
1.8
2.5
V
IF=10mA
IR
Reverse Current
Super Bright Red
10
uA
VR=5V
Notes:
1. Wavelength: +/-1nm.
2. Forward Voltage: +/-0.1V.
3. Wavelength value is traceable to CIE127-2007 standards.
4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or
premature failure.
Absolute Maximum Ratings at TA=25°C
Parameter
Values
Units
Power dissipation
75
mW
DC Forward Current
30
mA
Peak Forward Current [1]
155
mA
5
V
Reverse Voltage
Operating Temperature
-40°C To +85°C
Storage Temperature
-40°C To +100°C
Notes:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
2. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static
electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033.
SPEC NO: DSAN3492
REV NO: V.4B
DATE: SEP/22/2016
PAGE: 2 OF 7
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: W.Q.Zhong
ERP: 1102015728
Super Bright Red
AA3528AVU/ASRS
SPEC NO: DSAN3492
REV NO: V.4B
DATE: SEP/22/2016
PAGE: 3 OF 7
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: W.Q.Zhong
ERP: 1102015728
AA3528AVU/ASRS
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Reel Dimension
Tape Dimensions
(Units : mm)
SPEC NO: DSAN3492
REV NO: V.4B
DATE: SEP/22/2016
PAGE: 4 OF 7
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: W.Q.Zhong
ERP: 1102015728
PACKING & LABEL SPECIFICATIONS
AA3528AVU/ASRS
Terms and conditions for the usage of this document
1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.
2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without
notice. Before production usage customer should refer to the latest datasheet for the updated specifications.
3. When using the products referenced in this document, please make sure the product is being operated within the environmental
and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible
for any subsequent issues.
4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has
special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with
Kingbright representative for further assistance.
5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.
6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes
SPEC NO: DSAN3492
REV NO: V.4B
DATE: SEP/22/2016
PAGE: 5 OF 7
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: W.Q.Zhong
ERP: 1102015728
Application Notes
Introduction
Kingbright AA3528AVU series are surface-mounted right-angle light-emitting diode (LED) circuitboard indicators. It offers the convenience of surface-mount production while offering the right-angle
height profile of circuit-board indicator lamps. The part is suitable for automated SMT and lead-free
reflow soldering production. The clear silicone lens extends out to provide broad viewing angles.
When installed on customer’s circuit board, it can provide illuminated indication or backlight panel
indicators.
Transport and Storage
Surface mount devices (SMD) are moisture sensitive components. atmospheric moisture will seep
into the component package, so when placed on the circuit board for 160-200°C reflow soldering,
the high temperatures cause the absorbed moisture to vaporize and rapidly expand, creating vapor
pressure that could damage the LED component by causing cracks in the lens, delamination of the
chip and wire bonds, or other reliability issues.
1. Transportation
The product is packed in anti-static, moisture-proof mylar bags. The package should be carefully
handled to avoid external pressure and accidental puncture during transport.Proper anti-static
practices should be in place. If package leakage or damage is found before opening, suggest
customer take the damaged package off-line for additional testing and bake to dry before use.
2. Storage Conditions (Before Opening)
To prevent moisture-absorption reliability issues, the parts must be properly stored. Suggest do
not open the moisture-proof package until immediately before usage (except for sample inspection
purposes).The opened package must be re-sealed with fresh desiccant and humidity indicator and
Stored in a dry box (<30℃/60% RH).
3. Humidity Control (After Opening)
After opening the moisture-proof packaging, immediately check the humidity indicator card contained
inside to confirm the parts have been exposed to excess moisture.The production environment should
follow IPC/JEDEC J-STD-020 standards for temperature,humidity, and exposure time.
SMD environmental exposure time accumulates as long as the parts are outside the packaging,
unless they are being baked dry.
Table 1: IPC/JEDEC J-STD-020 Moisture Sensitivity Levels (MSL)
Allowed Exposure After Opening
MSL
Time
Conditions
LEVEL 1
No Limit
≦30℃/85%RH
LEVEL 2
1 Year
≦30℃/60%RH
LEVEL 2a
4 Weeks
≦30℃/60%RH
LEVEL 3
168 Hours
≦30℃/60%RH
LEVEL 4
72 Hours
≦30℃/60%RH
LEVEL 5
48 Hours
≦30℃/60%RH
LEVEL 5a
24 Hours
≦30℃/60%RH
LEVEL 6
Immediately upon open
≦30℃/60%RH
4. Storage of Unused And Remaining Parts
If the full reel was not consumed during production, the production environment was within limits
(<30℃/60% RH), and the exposure time did not exceed the limits in Table 1, then the remaining
parts may be stored as below:
z Re-sealed with desiccant.
z Stored within a dry box (5% RH). The dry box storage time would not count against the
total exposure time. When the stored parts are taken out, the exposure time is accumulated from the previous production run.
SPEC NO: DSAN3492
REV NO: V.4B
DATE: SEP/22/2016
PAGE: 6 OF 7
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: W.Q.Zhong
ERP: 1102015728
Application Notes
5. Humidity Control Of PCB-Mounted Parts
If the moisture-sensitive SMD parts will not undergo further reflow or other high-temperature
processes, then no special treatment is required. However, if the PCB assembly requires further
reflow or other high-temperature process, including rework, then the mounted SMD’s exposure time
should continue to accumulate against the MSL limit, unless the board is kept in a dry environ ment
(<5% RH).If the exposure time exceeds the MSL limit, the board and part must be baked dry to reset
the exposure time before undergoing further reflow.
Installation and Usage
If the part’s silicone lens extends beyond the board’s edge after installation, proper protection
Should be made (such as covers) to prevent accidental impact or stress on the exposed lens that
would cause damage or detachment. The silicone lens may withstand up to 1.5-newton in shear
force when properly mounted.If external protection is not available, strongly suggest following these
handling procedures to prevent damage:
1. When the PCB assembly is handled or transported after reflow soldering, care must be taken to
prevent accidental contact or impact on the exposed silicone lens.
2. When the PCB assembly is installed into the casing or panel, care must be taken to maintain
sufficient clearance for the lens.
3. Do not subject the silicone lens to outside impact or friction.
Cleaning
1. Do not use unknown chemicals or acidic solvents to clean the part. Please check to insure the
cleaning solvent will notcorode epoxy resin, silicone resin, silver plating, and other component
materials before using.
2. Kingbright suggests ethanol as a safe solvent for use with the surface mount devices. Softly wipe
away any surface partcles,avoiding excessive force scratching the surface or damaging the structures. Then place down and allow to naturally dry under room temperature conditions before further
use. Do not soak the component in the solvent.
SPEC NO: DSAN3492
REV NO: V.4B
DATE: SEP/22/2016
PAGE: 7 OF 7
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: W.Q.Zhong
ERP: 1102015728
Similar pages