AD ADV3228 750 mhz, 8 x 8 analog crosspoint switch Datasheet

FUNCTIONAL BLOCK DIAGRAM
SER/PAR
D0 D1 D2 D3
A0
A1
A2
CLK
40-BIT SHIFT REGISTER
WITH 4-BIT
PARALLEL LOADING
DATAIN
UPDATE
PARALLEL LATCH
CE
RESET
32
64
8
OUTPUT
BUFFER
G = +1,
G = +2
SWITCH
APPLICATIONS
09318-001
Routing of high speed signals including
Video (NTSC, PAL, S, SECAM, YUV, RGB)
Compressed video (MPEG, wavelet)
3-level digital video (HDB3)
Data communications
Telecommunications
SET INDIVIDUAL
OR RESET ALL
OUTPUTS TO OFF
DECODE
8 × 4:8 DECODERS
ADV3228/
ADV3229
DATAOUT
8 (RESERVED)
32
8
INPUTS
8 × 8 high speed, nonblocking switch array
Pinout and functionally equivalent to the AD8108/AD8109
Drop-in compatible with ADV3224/ADV3225 16 × 8 array
Complete solution
Buffered inputs
Programmable high impedance outputs
8 output amplifiers, G = +1 (ADV3228), G = +2 (ADV3229)
Drives 150 Ω loads
Operates on ±5 V supplies
Low power: 0.5 W
Excellent ac performance
−3 dB bandwidth
200 mV p-p: 1200 MHz (ADV3228), 900 MHz (ADV3229)
2 V p-p: 750 MHz (ADV3228), 850 MHz (ADV3229)
0.5 dB flatness (2 V p-p): 250 MHz (ADV3228), 235 MHz
(ADV3229)
Slew rate: 2500 V/µs
Serial or parallel programming of switch array
72-lead LFCSP (10 mm × 10 mm)
8
OUTPUTS
FEATURES
ENABLED/DISABLED
Data Sheet
750 MHz, 8 × 8 Analog Crosspoint Switch
ADV3228/ADV3229
Figure 1.
GENERAL DESCRIPTION
The ADV3228/ADV3229 are high speed 8 × 8 analog crosspoint
switch matrices. They offer a −3 dB large signal bandwidth of
750 MHz (ADV3228) and a slew rate of 2500 V/µs.
The ADV3228/ADV3229 include eight independent output buffers
that can be placed into a high impedance state for paralleling
crosspoint outputs to prevent off channels from loading the output
bus. The ADV3228 has a gain of +1, the ADV3229 has a gain of
+2, and they both operate on voltage supplies of ±5 V. Channel
Rev. A
switching is performed via a serial digital control that can
accommodate daisy chaining of several devices or via a parallel
control to allow updating of an individual output without
reprogramming the entire array.
The ADV3228/ADV3229 are available in the 72-lead LFCSP
package over the extended industrial temperature range of
−40°C to +85°C.
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2010–2016 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
ADV3228/ADV3229
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Pin Configuration and Function Descriptions..............................8
Applications ....................................................................................... 1
Truth Table and Logic Diagram ............................................... 10
Functional Block Diagram .............................................................. 1
Typical Performance Characteristics ........................................... 11
General Description ......................................................................... 1
Circuit Diagrams ............................................................................ 20
Revision History ............................................................................... 2
Theory of Operation ...................................................................... 21
Specifications..................................................................................... 3
Applications Information .............................................................. 22
Timing Characteristics (Serial) .................................................. 5
Serial Programming ................................................................... 22
Logic Levels ................................................................................... 5
Parallel Programming ................................................................ 22
Timing Characteristics (Parallel) ............................................... 6
Power-On Reset .......................................................................... 23
Absolute Maximum Ratings ............................................................ 7
Gain Selection ............................................................................. 23
Thermal Resistance ...................................................................... 7
Creating Larger Crosspoint Arrays .......................................... 23
Power Dissipation ......................................................................... 7
Outline Dimensions ....................................................................... 24
ESD Caution .................................................................................. 7
Ordering Guide .......................................................................... 24
REVISION HISTORY
1/16—Rev. 0 to Rev. A
Change to Maximum Potential Difference (DVCC to AVEE)
Parameter, Table 5............................................................................. 7
Updated Outline Dimensions ....................................................... 24
11/10—Revision 0: Initial Version
Rev. A | Page 2 of 24
Data Sheet
ADV3228/ADV3229
SPECIFICATIONS
VS = ±5 V, TA = 25°C, RL = 150 Ω, unless otherwise noted.
Table 1.
Parameter
DYNAMIC PERFORMANCE
−3 dB Bandwidth
Gain Flatness
Propagation Delay
Settling Time
Slew Rate
NOISE/DISTORTION PERFORMANCE
Differential Gain Error
Differential Phase Error
Crosstalk, All Hostile, RTO
Off Isolation, Input to Output
OIP2
OIP3
Output 1 dB Compression Point
Input Voltage Noise Density
DC PERFORMANCE
Gain Error
Gain Matching
Gain Temperature Coefficient
OUTPUT CHARACTERISTICS
Output Resistance
Output Disabled Capacitance
Output Leakage Current
Output Voltage Range
Short-Circuit Current
INPUT CHARACTERISTICS
Input Offset Voltage
Input Offset Voltage Drift
Input Voltage Range
Input Capacitance
Input Resistance
Input Bias Current
SWITCHING CHARACTERISTICS
Enable/Disable Time
Switching Time, 2 V Step
Switching Transient (Glitch)
Test Conditions/Comments
Min
ADV3228
Typ
Max
Min
ADV3229
Typ
Max
Unit
200 mV p-p
2 V p-p
0.1 dB, 2 V p-p
0.5 dB, 2 V p-p
2 V p-p
1%, 2 V step
2 V step, peak
1200
750
55
250
0.6
3
2500
900
850
50
235
0.6
3
2500
MHz
MHz
MHz
MHz
ns
ns
V/µs
NTSC or PAL
NTSC or PAL
f = 100 MHz
f = 5 MHz
f = 100 MHz, one channel
f = 100 MHz, RL = 100 Ω
f = 500 MHz, RL = 100 Ω
f = 100 MHz, RL = 100 Ω
f = 500 MHz, RL = 100 Ω
f = 100 MHz, RL = 100 Ω
f = 500 MHz, RL = 100 Ω
50 MHz
0.01
0.01
−45
−87
−80
0.02
0.02
−45
−70
−87
38
15
32
7
19
10
18
%
Degrees
dB
dB
dB
dBm
dBm
dBm
dBm
dBm
dBm
nV/√Hz
18
0.1
0.5
5
%
%
ppm/°C
0.2
15
2.2
0.5
±3
±2.8
55
0.2
8
2.6
0.5
±3
±2.8
55
Ω
MΩ
pF
µA
V
V
mA
±5
5
±3
1.8
2
±1
±5
5
±1.5
1.8
2
±1
mV
µV/°C
V
pF
MΩ
µA
20
20
25
20
20
50
ns
ns
mV p-p
Channel-to-channel
DC, enabled
DC, disabled
Output disabled
No load
RL = 150 Ω
Worst case (all configurations)
Any switch configuration
Any switch configuration
50% UPDATE to 1% settling
50% UPDATE to 1% settling
Rev. A | Page 3 of 24
0.5
0.5
0.2
1.5
1.5
ADV3228/ADV3229
Parameter
POWER SUPPLIES
Supply Current
Supply Voltage Range
PSRR
OPERATING TEMPERATURE RANGE
Temperature Range
θJA
Data Sheet
Test Conditions/Comments
Min
AVCC, outputs enabled, no load
AVCC, outputs disabled
AVEE, outputs enabled, no load
AVEE, outputs disabled
DVCC, outputs enabled, no load
±4.5
DC to 50 kHz, AVCC, AVEE
f = 100 kHz, AVCC, AVEE
f = 10 MHz, AVCC
f = 10 MHz, AVEE
f = 100 MHz, AVCC
f = 100 MHz, AVEE
f = 100 kHz, DVCC
Operating (still air)
Operating (still air)
ADV3228
Typ
Max
52
12
52
12
6
±5
<−60
−60
−48
−35
−25
−15
−90
−40
29
Rev. A | Page 4 of 24
Min
70
18
70
18
±5.5
±4.5
+85
−40
ADV3229
Typ
Max
58
13
58
14
6
±5
<−60
−60
−35
−55
−15
−15
−90
70
18
70
18
±5.5
+85
29
Unit
mA
mA
mA
mA
mA
V
dB
dB
dB
dB
dB
dB
dB
°C
°C/W
Data Sheet
ADV3228/ADV3229
TIMING CHARACTERISTICS (SERIAL)
Table 2.
Parameter
Serial Data Setup Time
CLK Pulse Width
Serial Data Hold Time
CLK Pulse Separation, Serial Mode
CLK to UPDATE Delay
UPDATE Pulse Width
CLK to DATAOUT Valid, Serial Mode
Propagation Delay, UPDATE to Switch On or Off
Data Load Time, CLK = 5 MHz, Serial Mode
CLK, UPDATE Rise and Fall Times
RESET Time
Symbol
t1
t2
t3
t4
t5
t6
t7
Min
10
10
10
10
10
10
Typ
Max
Unit
ns
ns
ns
ns
ns
ns
ns
ns
µs
ns
ns
50
20
8
50
30
Timing Diagram—Serial Mode
t2
t4
1
CLK
0
t1
LOAD DATA INTO
SERIAL REGISTER
ON FALLING EDGE
t3
1
DATAIN
OUT07 (D3)
OUT07 (RESERVED)
OUT00 (D0)
0
t5
t6
1 = LATCHED
UPDATE
0 = TRANSPARENT
TRANSFER DATA FROM SERIAL
REGISTER TO PARALLEL
LATCHES DURING LOW LEVEL
09318-002
t7
DATAOUT
Figure 2. Timing Diagram, Serial Mode
LOGIC LEVELS
Table 3. Logic Levels
VIH
RESET,
SER/PAR, CLK,
DATA IN, CE,
UPDATE
2.0 V min
VIL
RESET,
SER/PAR, CLK,
DATA IN, CE,
UPDATE
0.8 V max
VOH
DATA OUT
VOL
DATA OUT
IIH
SER/PAR,
CLK, DATA IN,
CE, UPDATE
IIL
SER/PAR,
CLK, DATA IN,
CE, UPDATE
IIH
RESET
IIL
RESET
IOH
DATA OUT
IOL
DATA OUT
2.4 V min
0.4 V max
2 µA max
2 µA max
2 µA max
300 µA max
3 mA min
1 mA min
Rev. A | Page 5 of 24
ADV3228/ADV3229
Data Sheet
TIMING CHARACTERISTICS (PARALLEL)
Table 4.
Parameter
Parallel Data Setup Time
Address Setup Time
CLK Pulse Width
Parallel Data Hold Time
Address Hold Time
CLK Pulse Separation
UPDATE Pulse Width
CLK, UPDATE Rise and Fall Times
RESET Time
Symbol
t1d
t1a
t2
t3d
t3a
t4
t5
Min
10
10
10
10
10
20
10
Typ
Max
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
50
30
Timing Diagram—Parallel Mode
t2
1
CLK
0
1
A0 TO A2
0
1
D0 TO D3
0
t4
t1a
t3a
t1d
t3d
t5
09318-003
1 = LATCHED
UPDATE
0 = TRANSPARENT
Figure 3. Timing Diagram, Parallel Mode
Rev. A | Page 6 of 24
Data Sheet
ADV3228/ADV3229
ABSOLUTE MAXIMUM RATINGS
POWER DISSIPATION
Table 5.
11 V
AVEE < VIN < AVCC
DGND < DIN < DVCC
AGND
AVEE < VOUT < AVCC
Momentary
Internally limited
to 55 mA
−65°C to +125°C
−40°C to +85°C
150°C
300°C
Packaged in the 72-lead LFCSP, the ADV3228/ADV3229 junctionto-ambient thermal impedance (θJA) is 29°C/W. For long-term
reliability, the maximum allowed junction temperature of the
die should not exceed 125°C; even temporarily exceeding this
limit can cause a shift in parametric performance due to a change
in stresses exerted on the die by the package. Exceeding a junction
temperature of 150°C for an extended period can result in device
failure. In Figure 4, the curve shows the range of allowed internal
die power dissipation that meets these conditions over the −40°C
to +85°C ambient temperature range. When using Figure 4, do
not include the external load power in the maximum power
calculation, but do include the load current dropped on the die
output transistors.
7
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
THERMAL RESISTANCE
5
4
3
2
1
–20
θJA
29
θJC
0.5
0
20
40
AMBIENT TEMPERATURE (°C)
60
80
Figure 4. Maximum Die Power Dissipation vs. Ambient Temperature
ESD CAUTION
Table 6. Thermal Resistance
Package Type
72-Lead LFCSP_VQ
6
0
–40
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
TJ = 150°C
09318-004
Temperature
Storage Temperature Range
Operating Temperature Range
Junction Temperature
Lead Temperature
(Soldering, 10 sec)
The ADV3228/ADV3229 operate with ±5 V supplies and can
drive loads down to 100 Ω, resulting in a wide range of possible
power dissipations. For this reason, extra care must be taken when
derating the operating conditions based on ambient temperature.
Rating
11 V
6V
±0.5 V
±0.5 V
MAXIMUM POWER DISSIPATION (W)
Parameter
Analog Supply Voltage (AVCC to AVEE)
Digital Supply Voltage (DVCC to DGND)
Supply Potential Difference (AVCC to DVCC)
Ground Potential Difference
(AGND to DGND)
Maximum Potential Difference
(DVCC to AVEE)
Analog Input Voltage
Digital Input Voltage
Exposed Paddle Voltage
Output Voltage (Disabled Analog Output)
Output Short Circuit
Duration
Current
Unit
°C/W
Rev. A | Page 7 of 24
ADV3228/ADV3229
Data Sheet
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
AGND
NC
AVEE
NC
AVCC
NC
AVEE
NC
AVCC
NC
AVEE
NC
AVCC
NC
AVEE
NC
AGND
DVCC
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
PIN 1
INDICATOR
ADV3228/ADV3229
TOP VIEW
(Not to Scale)
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
DGND
RESET
CE
DATAOUT
CLK
DATAIN
UPDATE
SER/PAR
A0
A1
A2
D0
D1
D2
D3
NC
DGND
DVCC
NOTES
1. NC = NO CONNECT. DO NOT CONNECT TO THIS PIN.
2. EXPOSED PADDLE. THE EXPOSED METAL PADDLE ON THE BOTTOM OF
THE LFCSP PACKAGE MUST BE SOLDERED TO THE PCB AGND FOR
PROPER HEAT DISSIPATION AND FOR NOISE AND MECHANICAL
STRENGTH BENEFITS.
Figure 5. Pin Configuration
Table 7. Pin Function Descriptions
Pin No.
1, 5, 9, 13, 19, 23, 27, 31, 35, 60, 64, 68
2
3, 7, 11, 15, 18, 21, 25, 29, 33, 36, 58, 62, 66, 70
4
6
8
10
12
14
16
17, 56, 72
20
22
24
26
28
30
32
34
37, 55
38, 54
39, 57, 59, 61, 63, 65, 67, 69, 71
Mnemonic
AVCC
IN0
AVEE
IN1
IN2
IN3
IN4
IN5
IN6
IN7
AGND
OUT7
OUT6
OUT5
OUT4
OUT3
OUT2
OUT1
OUT0
DVCC
DGND
NC
Description
Analog Positive Supply.
Input Number 0.
Analog Negative Supply.
Input Number 1.
Input Number 2.
Input Number 3.
Input Number 4.
Input Number 5.
Input Number 6.
Input Number 7.
Analog Ground.
Output Number 7.
Output Number 6.
Output Number 5.
Output Number 4.
Output Number 3.
Output Number 2.
Output Number 1.
Output Number 0.
Digital Positive Supply.
Digital Ground.
No Internal Connection.
Rev. A | Page 8 of 24
09318-005
AVCC
OUT7
AVEE
OUT6
AVCC
OUT5
AVEE
OUT4
AVCC
OUT3
AVEE
OUT2
AVCC
OUT1
AVEE
OUT0
AVCC
AVEE
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
AVCC
IN0
AVEE
IN1
AVCC
IN2
AVEE
IN3
AVCC
IN4
AVEE
IN5
AVCC
IN6
AVEE
IN7
AGND
AVEE
Data Sheet
Pin No.
40 to 43
44 to 46
47
48
49
50
51
52
53
ADV3228/ADV3229
Mnemonic
D3, D2, D1, D0
A2, A1, A0
SER/PAR
UPDATE
DATAIN
CLK
DATAOUT
CE
RESET
EPAD
Description
Parallel Data Input.
Parallel Output Address Input.
Serial/Parallel Mode Select (Control Pin).
Second Rank Write Strobe (Control Pin).
Serial Data In (Control Pin).
Serial Data Clock, Parallel First Rank Latch Enable (Control Pin).
Serial Data Out.
Chip Enable (Control Pin).
Second Rank Reset (Control Pin).
Exposed Paddle. The exposed metal paddle on the bottom of the LFCSP
package must be soldered to the PCB AGND for proper heat dissipation
and for noise and mechanical strength benefits.
Rev. A | Page 9 of 24
ADV3228/ADV3229
Data Sheet
TRUTH TABLE AND LOGIC DIAGRAM
Table 8. Operation Truth Table1
CE
1
0
UPDATE
X
X
CLK
X
DATAIN
X
DataI2
DATAOUT
X
DataI-80
RESET
X
X
SER/PAR
X
0
0
X
0
D0…D3
Not applicable in
parallel mode3
X
1
0
0
X
X
X
1
X
X
X
X
X
X
0
X
Description
No change in logic.
The data on the serial DATAIN line is loaded into the
serial register. The first bit clocked into the serial
register appears at DATAOUT 40 clock cycles later.
The data on the parallel data lines, D0 to D3, are
loaded into the 40-bit serial shift register location
addressed at A0 to A2.
Data in the 40-bit shift register transfers into the
parallel latches that control the switch array. Latches
are transparent.
Asynchronous operation. All outputs are disabled.
Second rank latches are cleared. Remainder of logic
is unchanged.
X is don’t care.
DataI: serial data. Reserved bit internally set to Logic 1.
3
DATAOUT remains active in parallel mode and always reflects the state of the MSB of the serial shift register.
1
2
PARALLEL
DATA
D0
D1
D2
RESERVED
(INTERNALLY
SET HIGHT)
(OUTPUT
ENABLE) D3
SER/PAR
S
D1
Q
D0
DATAIN
(SERIAL)
S
D1
D Q
Q
D0
CLK
S
D1
S
D1
D Q
Q
D0
CLK
D Q
Q
D0
CLK
D Q
CLK
S
D1
S
D1
Q D Q
D0
CLK
Q
D0
D Q
CLK
S
D1
S
D1
Q D Q
D0 CLK
Q
D0
S
D1
S
D1
D Q
Q
D0
CLK
D Q
Q
D0
CLK
S
D1
S
D1
D Q
Q
D0
CLK
D Q
Q
D0
CLK
D Q
DATA
OUT
CLK
CLK
CE
UPDATE
A0
A1
A2
3 TO 8 DECODER
OUTPUT
ADDRESS
OUT0 EN
OUT1 EN
OUT2 EN
OUT3 EN
OUT4 EN
OUT5 EN
OUT6 EN
OUT7 EN
LE D
LE D
LE D
LE D
LE D
LE D
LE D
LE D
LE D
LE D
LE D
OUT0
B0
OUT0
B1
OUT0
B2
OUT0
R
OUT0
EN
OUT1
B0
OUT6
EN
OUT7
B0
OUT7
B1
OUT7
B2
OUT7
R
OUT7
EN
Q
Q
Q
Q
Q
CLR Q
Q
Q
Q
Q
CLR Q
CLR Q
LE D
RESET
(OUTPUT ENABLE)
SWITCH MATRIX
Figure 6. Logic Diagram
Rev. A | Page 10 of 24
8
OUTPUT ENABLE
09318-006
DECODE
128
Data Sheet
ADV3228/ADV3229
VOUT = 200mV p-p
100
1000
10000
FREQUENCY (MHz)
VOUT = 200mV p-p
1
GAIN (dB)
GAIN (dB)
100
1000
10000
FREQUENCY (MHz)
09318-009
VOUT = 2V p-p
10
10
9
8
7
6
5
4
3
2
1
0
–1
–2
–3
–4
–5
–6
–7
–8
–9
–10
VOUT = 2V p-p
1
5.2pF
GAIN (dB)
2.2pF
0pF
VOUT = 200mV p-p
10
100
FREQUENCY (MHz)
1000
100
1000
10000
Figure 11. ADV3229 Large Signal Frequency Response
1.2pF
1
10
FREQUENCY (MHz)
10000
09318-010
GAIN (dB)
10.4pF
10000
OUTPUT SIGNAL, UNICAST
OUTPUT SIGNAL, BROADCAST
Figure 8. ADV3228 Large Signal Frequency Response
6
5
4
3
2
1
0
–1
–2
–3
–4
–5
–6
–7
–8
–9
–10
1000
Figure 10. ADV3229 Small Signal Frequency Response
OUTPUT SIGNAL, UNICAST
OUTPUT SIGNAL, BROADCAST
1
100
FREQUENCY (MHz)
Figure 7. ADV3228 Small Signal Frequency Response
4
3
2
1
0
–1
–2
–3
–4
–5
–6
–7
–8
–9
–10
–11
–12
10
09318-012
10
OUTPUT SIGNAL, UNICAST
OUTPUT SIGNAL, BROADCAST
Figure 9. ADV3228 Small Signal Frequency Response with Capacitive Loads
Rev. A | Page 11 of 24
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
–1
–2
–3
–4
–5
–6
–7
–8
–9
–10
10.4pF
5.2pF
2.2pF
1.2pF
0pF
VOUT = 200mV p-p
1
10
100
1000
10000
FREQUENCY (MHz)
Figure 12. ADV3229 Small Signal Frequency Response, RL = 150 Ω
09318-013
1
10
9
8
7
6
5
4
3
2
1
0
–1
–2
–3
–4
–5
–6
–7
–8
–9
–10
09318-011
OUTPUT SIGNAL, UNICAST
OUTPUT SIGNAL, BROADCAST
GAIN (dB)
4
3
2
1
0
–1
–2
–3
–4
–5
–6
–7
–8
–9
–10
–11
–12
09318-008
GAIN (dB)
TYPICAL PERFORMANCE CHARACTERISTICS
ADV3228/ADV3229
Data Sheet
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
–1
–2
–3
–4
–5
–6
–7
–8
–9
–10
3
10.4pF
2
5.2pF
1
2.2pF
0
GAIN (dB)
1.2pF
–2
–3
0pF
–4
–5
–6
–7
–8
100
10
10000
1000
FREQUENCY (MHz)
09318-014
VOUT = 2V p-p
1
Figure 13. ADV3228 Large Signal Frequency Response with Capacitive Loads
1.2pF
0.15
0.05
0.05
VOUT (V)
0.10
INPUT
OUTPUT SIGNAL, UNICAST
OUTPUT SIGNAL, BROADCAST
0
–0.05
–0.05
–0.10
–0.10
VOUT = 200mV p-p
2
4
6
VOUT = 200mV p-p
10
8
12
14
16
18
20
TIME (ns)
–0.15
09318-015
0
0
4
6
8
10
12
14
16
18
20
20
Figure 17. ADV3229 Small Signal Pulse Response
1.5
INPUT SIGNAL
OUTPUT SIGNAL, UNICAST
OUTPUT SIGNAL, BROADCAST
0.10
INPUT
OUTPUT SIGNAL, UNICAST
OUTPUT SIGNAL, BROADCAST
1.0
0.05
0.5
VOUT (V)
VOUT (V)
2
TIME (ns)
Figure 14. ADV3228 Small Signal Pulse Response
0.15
10000
1000
Figure 16. ADV3229 Large Signal Frequency Response with Capacitive Loads
0.10
–0.15
100
10
FREQUENCY (MHz)
INPUT SIGNAL
OUTPUT SIGNAL, UNICAST
OUTPUT SIGNAL, BROADCAST
0
0pF
VOUT = 2V p-p
1
0.15
VOUT (V)
2.2pF
09318-018
–9
–10
5.2pF
09318-019
GAIN (dB)
–1
10.4pF
09318-017
4
0
–0.05
0
–0.5
–0.10
–1.0
VOUT = 2V p-p
0
2
4
6
8
10
12
14
16
18
Time (ns)
20
09318-016
VOUT = 2V p-p
–0.15
Figure 15. ADV3228 Large Signal Pulse Response
–1.5
0
2
4
6
8
10
12
14
16
18
TIME (ns)
Figure 18. ADV3229 Large Signal Pulse Response
Rev. A | Page 12 of 24
Data Sheet
2.0
ADV3228/ADV3229
3000
2.0
1.5
2500
1.5
1.0
2000
1.0
0.5
1500
0
1000
RISING EDGE PULSE
RISING EDGE SLEW RATE
4000
3500
VOUT (V)
0.5
2000
1500
0
–0.5
500
–1.0
0
–1.0
–1.5
–500
–1.5
SLEW RATE (V/μs)
2500
SLEW RATE (V/μs)
VOUT (V)
3000
1000
–0.5
500
0
–500
1.0
0.5
1.5
2.0
3.0
2.5
3.5
4.0
4.5
–2.0
09318-020
0
–1000
5.0
TIME (ns)
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
–1000
5.0
09318-022
RISING EDGE PULSE
RISING EDGE SLEW RATE
–2.0
TIME (ns)
Figure 19. ADV3228 Rising Edge Slew Rate
Figure 22. ADV3229 Rising Edge Slew Rate
500
2.0
1000
2.0
FALLING EDGE PULSE
FALLING EDGE SLEW RATE
1.5
0
1.5
1.0
–500
1.0
0.5
–1000
0
–1500
–0.5
–2000
–1.0
–2500
–1.0
–1.5
–3000
–1.5
–3500
5.0
–2.0
500
VOUT (V)
0.5
–1000
–1500
0
–2000
–0.5
–2500
SLEW RATE (V/μs)
–500
SLEW RATE (V/μs)
VOUT (V)
0
–3000
–3500
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
TIME (ns)
0
0.5
1.0
1.5
2.0
3.0
2.5
3.5
4.0
4.5
–4000
5.0
09318-023
0
09318-021
FALLING EDGE PULSE
FALLING EDGE SLEW RATE
–2.0
TIME (ns)
Figure 20. ADV3228 Falling Edge Slew Rate
Figure 23. ADV3229 Falling Edge Slew Rate
40
1.5
40
1.5
INPUT SIGNAL
OUTPUT–INPUT
30
1.0
30
1.0
0
–1.0
–10
–1.5
–2.0
OUTPUT SIGNAL
10
0
–0.5
0
–1.0
–10
PROPAGATION DELAY NOT SHOWN
–1.5
–1.0
–0.5
0
0.5
1.0
1.5
2.0
TIME (ns)
2.5
–20
3.0
OUTPUT ERROR (%)
–0.5
20
INPUT SIGNAL
PROPAGATION DELAY NOT SHOWN
–1.5
–1.0
Figure 21. ADV3228 Settling Time
–0.5
0
0.5
1.0
1.5
2.0
2.5
3.0
TIME (ns)
Figure 24. ADV3229 Settling Time
Rev. A | Page 13 of 24
3.5
–20
4.0
09318-050
10
0
0.5
VOUT (V)
20
OUTPUT SIGNAL
09318-049
VOUT (V)
0.5
OUTPUT ERROR (%)
OUTPUT–INPUT
ADV3228/ADV3229
Data Sheet
20
20
10
0
–10
–20
–20
PSR (dB)
0
–10
–30
VCC AGGRESSOR
–40
–30
–40
–50
–50
–60
–60
–70
–70
–80
–80
–90
0.1
1
100
10
1k
FREQUENCY (MHz)
VCC AGGRESSOR
VEE AGGRESSOR
–90
0.1
1
10
100
1k
FREQUENCY (MHz)
Figure 25. ADV3228 Power Supply Rejection
09318-052
VEE AGGRESSOR
09318-051
PSR (dB)
10
Figure 28. ADV3229 Power Supply Rejection
400
700
650
350
600
550
500
NOISE (nV/Hz)
NOISE (nV/√Hz)
300
250
200
150
450
400
350
300
250
200
100
150
100
50
10
100
1000
10000
100000
FREQUENCY (kHz)
0
09318-024
1
1
10
100
1000
10000
100000
FREQUENCY (kHz)
Figure 26. ADV3228 Output Noise, 100 Ω Load
09318-026
50
0
Figure 29. ADV3229 Output Noise, 100 Ω Load
–40
–20
–50
–40
ISOLATION (dB)
–70
–80
–90
–60
–80
–100
–100
–120
–120
1
10
100
FREQUENCY (MHz)
1000
Figure 27. ADV3228 Off Isolation
–140
1
10
100
FREQUENCY (MHz)
Figure 30. ADV3229 Off Isolation
Rev. A | Page 14 of 24
1000
09318-027
–110
09318-025
ISOLATION (dB)
–60
ADV3228/ADV3229
0
IN11-OUT3: VICTIM CHANNEL
–10 IN12-OUT4: AGGRESSOR
VOUT = 2V p-p
–20
–10
–30
–30
0
–40
–50
–60
–70
–80
–40
–50
–60
–70
–90
–100
–100
10
100
1000
FREQUENCY (MHz)
–110
09318-029
1
1
10
100
1000
FREQUENCY (MHz)
Figure 31. ADV3228 Crosstalk, One Adjacent Channel, RTO
09318-032
–80
–90
–110
IN11-OUT3:VICTIM CHANNEL
IN12-OUT4: AGGRESSOR
VOUT = 2V p-p
–20
CROSSTALK (dB)
CROSSTALK (dB)
Data Sheet
Figure 34. ADV3229 Crosstalk, One Adjacent Channel, RTO
0
IN3-OUT3: VICTIM CHANNEL
–10 VOUT = 2V p-p
20
IN3-OUT3: VICTIM CHANNEL
VOUT = 2V p-p
10
0
–20
–10
CROSSTALK (dB)
CROSSTALK (dB)
–30
–40
–50
–60
–70
–20
–30
–40
–50
–60
–70
–80
–80
–90
–90
–100
10
1000
100
FREQUENCY (MHz)
–110
1
1000
Figure 35. ADV3229 Crosstalk, All Hostile, RTO
1M
100k
100k
10k
10k
IMPEDANCE (Ω)
1M
1k
100
10
1k
100
1
10
100
1000
FREQUENCY (MHz)
10000
Figure 33. ADV3228 Input Impedance
1
0.1
1
10
100
1000
FREQUENCY (MHz)
Figure 36. ADV3229 Input Impedance
Rev. A | Page 15 of 24
10000
09318-034
10
09318-031
IMPEDANCE (Ω)
100
FREQUENCY (MHz)
Figure 32. ADV3228 Crosstalk, All Hostile, RTO
1
0.1
10
09318-033
1
09318-030
–110
–100
Data Sheet
1M
1M
100k
100k
10k
10k
IMPEDANCE (Ω)
1k
100
1k
100
1000
100
1
0.1
FREQUENCY (MHz)
10
IMPEDANCE (Ω)
10
IMPEDANCE (Ω)
100
1
1000
FREQUENCY (MHz)
0.1
0.1
1
100
10
Figure 41. ADV3229 Output Impedance, Enabled
2.0
UPDATE
3.5
2.0
3.0
1.5
3.5
UPDATE
3.0
VOUT RISING EDGE
VOUT RISING EDGE
2.5
1.0
2.5
0.5
2.0
0.5
2.0
0
1.5
0
1.5
1.0
–0.5
VOUT (V)
UPDATE (V)
1.0
1.0
–0.5
VOUT FALLING EDGE
–1.0
0.5
–1.0
–1.5
0
–1.5
–0.5
–2.0
–20
–2.0
–20
–15
–10
–5
0
5
10
15
20
TIME (ns)
25
30
09318-037
VOUT (V)
1000
FREQUENCY (MHz)
Figure 38. ADV3228 Output Impedance, Enabled
1.5
1000
1
09318-036
100
10
100
Figure 40. ADV3229 Output Impedance, Disabled
100
1
10
FREQUENCY (MHz)
Figure 37. ADV3228 Output Impedance, Disabled
0.1
0.1
1
09318-039
10
Figure 39. ADV3228 Switching Time
VOUT FALLING EDGE
0.5
0
–15
–10
–5
0
5
10
15
20
TIME (ns)
Figure 42. ADV3229 Switching Time
Rev. A | Page 16 of 24
UPDATE (V)
1
09318-035
1
0.1
09318-038
10
10
25
–0.5
30
09318-040
IMPEDANCE (Ω)
ADV3228/ADV3229
Data Sheet
ADV3228/ADV3229
3.5
0.0500
3.5
0.100
UPDATE
3.0
0.075
3.0
0.0250
2.5
0.050
2.5
2.0
0.025
1.5
–0.0125
1.0
–0.0250
–0.0375
–0.0500
–15
–10
–5
0
5
10
15
20
25
2.0
VOUT
0
1.5
–0.025
1.0
0.5
–0.050
0.5
0
–0.075
0
–0.5
–0.100
–15
30
TIME (ns)
–10
0
5
10
15
20
–0.5
30
25
TIME (ns)
Figure 43. ADV3228 Switching Glitch
Figure 46. ADV3229 Switching Glitch
4
4
3.5
UPDATE
3
–5
09318-044
0
VOUT (V)
VOUT (V)
VOUT
09318-041
0.0125
UPDATE (V)
0.0375
UPDATE (V)
UPDATE
2
3.0
3
2.5
2
3.5
UPDATE
3.0
2.5
2.0
0
1.5
VOUT FALLING EDGE
1
1.0
2
0.5
–2
0.5
3
0
–3
0
0.5
–4
–20
4
–20
–15
–10
–5
0
5
10
15
20
25
30
–1
TIME (ns)
–15
–10
–5
0
5
10
15
20
25
1.0
–0.5
30
09318-045
1.5
VOUT FALLING EDGE
VOUT (V)
0
1
UPDATE (V)
2.0
VOUT RISING EDGE
09318-042
VOUT (V)
1
UPDATE (V)
VOUT RISING EDGE
TIME (ns)
Figure 44. ADV3228 Enable Time
Figure 47. ADV3229 Enable Time
0.0045
0.014
0.0040
DIFFERENTIAL GAIN ERROR (%)
0.0030
0.0025
0.0020
0.0015
0.0010
0.0005
0.010
0.008
0.006
0.004
0.002
–0.0005
–0.8
–0.6
–0.4
–0.2
0
0.2
0.4
INPUT DC OFFSET (V)
0.6
0.8
Figure 45. ADV3228 Differential Gain Error
0
–0.7 –0.6 –0.5 –0.4 –0.3 –0.2 –0.1 0
0.1 0.2 0.3 0.4 0.5 0.6 0.7
INPUT DC OFFSET (V)
Figure 48. ADV3229 Differential Gain Error
Rev. A | Page 17 of 24
09318-046
0
09318-043
DIFFERENTIAL GAIN ERROR (%)
0.012
0.0035
ADV3228/ADV3229
Data Sheet
0.002
0
–0.001
–0.002
–0.003
–0.004
–0.005
–0.007
–0.7 –0.6 –0.5 –0.4 –0.3 –0.2 –0.1 0
0.1 0.2 0.3 0.4 0.5 0.6 0.7
INPUT VOLTAGE (V)
–0.002
–0.004
–0.006
–0.008
–0.010
–0.012
–0.014
–0.7 –0.6 –0.5 –0.4 –0.3 –0.2 –0.1 0
09318-047
–0.006
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7
INPUT VOLTAGE (V)
Figure 49. ADV3228 Differential Phase Error
09318-048
DIFFERENTIAL PHASE ERROR (Degrees)
DIFFERENTIAL PHASE ERROR (Degrees)
0.001
Figure 52. ADV3229 Differential Phase Error
5
5
4
4
3
VIN = 8.5V p-p
3
VIN = 8.5V p-p
2
VOLTAGE (V)
1
0
–1
–2
1
0
–1
–2
–3
–3
VOUT AT VIN = 8.5V p-p
VOUT AT VIN = 8.5V p-p
–4
–4
0
10
20
30
40
50
60
70
80
90
–5
09318-053
–5
100
TIME (ns)
0
10
30
40
50
60
70
80
90
100
TIME (ns)
Figure 53. ADV3229 Overdrive Recovery
Figure 50. ADV3228 Overdrive Recovery
22
20
09318-055
VOLTAGE (V)
2
40
REF: 50Ω
REF: 50Ω
18
16
14
12
30
25
20
15
10
5
RL = 100Ω
10
10
100
1000
INPUT FREQUENCY (MHz)
RL = 100Ω
TONE SPACING: 1MHz
0
10
100
INPUT FREQUENCY (MHz)
Figure 54. ADV3229 Third-Order Intercept, 100 Ω Load
Figure 51. ADV3229 1 dB Gain Compression, 100 Ω Load
Rev. A | Page 18 of 24
1000
09318-056
THIRD-ORDER INTERCEPT (dBm)
20
09318-054
1dB GAIN COMPRESSION (dBm)
35
Data Sheet
–20
REF: 50Ω
HARMONIC DISTORTION (dBc)
SECOND-ORDER INTERCEPT (dBm)
45
40
35
30
25
20
15
09318-057
100
1000
INPUT FREQUENCY (MHz)
Figure 55. ADV3229 Second-Order Intercept, 100 Ω Load
35
30
25
20
15
10
–16
–12
–8
–4
0
4
8
12
16
20
INPUT OFFSET VOLTAGE (mV)
09318-059
5
–20
HD2, 0dBm
–50
–60
HD3, 0dBm
–70
–80
HD3, 10dBm
–90
–110
10
RL = 100Ω
100
INPUT FREQUENCY (MHz)
Figure 57. ADV3229 Harmonic Distortion,100 Ω Load
40
0
–40
–100
RL = 100Ω
TONE SPACING: 1MHz
10
10
NUMBER OF HITS
HD2, 10dBm
–30
50
Figure 56. ADV3228 and ADV3229, Input VOS Distribution
Rev. A | Page 19 of 24
1000
09318-058
55
ADV3228/ADV3229
ADV3228/ADV3229
Data Sheet
CIRCUIT DIAGRAMS
INx
1.8pF
Figure 58. Analog Input
09318-064
09318-060
OUTx
2.4pF
Figure 62. Analog Output Disabled
OUTx
DVCC
20kΩ
1kΩ
DGND
Figure 59. Analog Output Enabled
AVCC
09318-065
09318-061
RESET
Figure 63. Reset Input
DVCC
DVCC
CLK, RESET,
SER/PAR, CE,
UPDATE,
DATAIN,
DATAOUT,
A[2:0], D[4:0]
AGND
DGND
DGND
Figure 64. Logic Output
Figure 60. ESD Map
1kΩ
DGND
09318-063
A[2:0], CE, CLK,
D[4:0], DATAIN,
SER/PAR, UPDATE
Figure 61. Logic Input
Rev. A | Page 20 of 24
09318-066
AGND
DATAOUT
09317-062
INx, OUTx
Data Sheet
ADV3228/ADV3229
THEORY OF OPERATION
The ADV3228 (G = +1) and ADV3229 (G = +2) are crosspoint
arrays with eight outputs, each of which can be connected to
any one of eight inputs. Organized by output row, eight switchable
input transconductance stages are connected to each output buffer
to form 8-to-1 multiplexers. There are eight of these multiplexers,
each with its inputs wired in parallel, for a total array of 64 transconductance stages forming a multicast-capable crosspoint
switch. Each input is buffered and is not loaded by the outputs,
simplifying the construction of larger arrays using the ADV3228
or ADV3229 as a building block.
A series of internal amplifiers drives internal nodes such that a
wideband high impedance is presented at the disabled output,
even while the output bus is under large signal swings. To keep
these internal amplifiers in their linear range of operation when
the outputs are disabled and driven externally, do not allow the
voltage applied to them to exceed the valid output swing range
for the ADV3228/ADV3229. If the disabled outputs are left
floating, they may exhibit high enable glitches. If necessary,
the disabled output can be kept from drifting out of range by
applying an output load resistor to ground.
Decoding logic for each output selects one (or none) of the
transconductance stages to drive the output stage. The enabled
transconductance stage drives the output stage, and feedback
forms a closed-loop amplifier. A mask programmable feedback
network sets the closed-loop signal gain. For the ADV3228, this
gain is +1, and for the ADV3229, this gain is +2.
The connection of the ADV3228/ADV3229 is controlled by a
flexible TTL-compatible logic interface. Either parallel or serial
loading into a first rank of latches preprograms each output. A
global update signal moves the programming data into the second
rank of latches, simultaneously updating all outputs. In serial
mode, a serial output pin allows devices to be daisy-chained
together for single pin programming of multiple ICs. A poweron reset pin is available to avoid bus conflicts by disabling all
outputs. This power-on reset clears the second rank of latches
but does not clear the first rank of latches. In serial mode, preprogramming individual inputs is not possible, and the entire
shift register must be flushed.
The output stage of the ADV3228 or ADV3229 is designed for
low differential gain and phase error when driving composite
video signals. It also provides slew current for a fast pulse response
when driving component video signals. Unlike many multiplexer
designs, these requirements are balanced such that large signal
bandwidth is very similar to small signal bandwidth. The design
load is 150 Ω, but provisions are made to drive loads as low as
100 Ω when on-chip power dissipation limits are not exceeded.
The outputs of the ADV3228/ADV3229 can be disabled to
minimize on-chip power dissipation. When disabled, there is no
feedback network loading the output. This high disabled output
impedance allows multiple ICs to be bussed together without
additional buffering. Take care to reduce output capacitance,
which results in more overshoot and frequency domain peaking.
To easily interface to ground-referenced video signals, the
ADV3228/ADV3229 operate on split ±5 V supplies. The logic
inputs and output run on a single 5 V supply, and the logic
inputs switch at approximately 1.6 V for compatibility with a
variety of logic families. The serial output buffer is a rail-to-rail
output stage with 5 mA of drive capability.
Rev. A | Page 21 of 24
ADV3228/ADV3229
Data Sheet
APPLICATIONS INFORMATION
The ADV3228/ADV3229 have two options for changing the
programming of the crosspoint matrix. In the first option, a
serial word of 40 bits can be provided, which updates the entire
matrix each time the 40-bit word is shifted into the device. The
second option allows for changing the programming of a single
output via a parallel interface. The serial option requires fewer
signals but more time (clock cycles) for changing the programming, whereas the parallel programming technique requires
more signals but can change a single output at a time and requires
fewer clock cycles to complete the programming.
SERIAL PROGRAMMING
The serial programming mode uses the CE, CLK, DATAIN,
UPDATE, and SER/PAR pins. The first step is to assert a low
on SER/PAR to enable the serial programming mode. CE for
the chip must be low to allow data to be clocked into the device.
The CE signal can be used to address an individual device when
devices are connected in parallel.
The UPDATE signal should be high during the time that data is
shifted into the serial port of the device. Although the data still shifts
in when UPDATE is low, the transparent, asynchronous latches
allow the shifting data to reach the matrix, which causes the matrix
to try to update to every intermediate state as defined by the
shifting data.
The data at DATAIN is clocked in at every falling edge of CLK, and
a total of 40 bits must be shifted in to fill the register, and thereby,
complete the programming. For each of the eight outputs there are
five bits in the shift register; the position of these bits in the register
determines the output to which they apply (see Figure 6). Three of
the bits (D0 to D2) determine the source of the input that connects
to the output that pertains to the position in the register; the MSB is
shifted in first. The fourth bit (reserved) is a reserved enable bit and
must be shifted in as a logic high prior to D0 to D2 in all cases (in
parallel programming mode this bit is internally set high). The fifth
bit (D3) precedes these four bits and determines the enabled state
of the output. If D3 is low (output disabled), the four associated
bits do not matter because no input switches to that output.
The most significant output address data is shifted in first, and the
remaining addresses follow in sequence until the least significant
output address data is shifted in. At this point, UPDATE can be
taken low, which programs the device according to the data that
was just shifted in. The update registers are asynchronous, and
when UPDATE is low (and CE is low), they are transparent.
If more than one ADV3228/ADV3229 device is to be serially
programmed in a system, the DATAOUT signal from one device
can be connected to the DATAIN of the next device to form a serial
chain. Connect all of the CLK, CE, UPDATE, and SER/PAR pins in
parallel and operate them as described previously in this section.
The serial data is input to the DATAIN pin of the first device of
the chain, and it ripples through to the last. Therefore, the data for
the last device in the chain should come at the beginning of the
programming sequence. The length of the programming sequence
(40 bits) is multiplied by the number of devices in the chain.
PARALLEL PROGRAMMING
When using the parallel programming mode, it is not necessary
to reprogram the entire device when making changes to the matrix.
Parallel programming allows the modification of a single output
at a time. Because this takes only one CLK/UPDATE cycle, significant time savings can be realized by using parallel programming.
An important consideration in using parallel programming is
that the RESET signal does not reset all registers in the ADV3228/
ADV3229. When taken low, the RESET signal sets each output
to the disabled state. This is helpful during power-up to ensure
that two parallel outputs are not active at the same time.
After initial power-up, the internal registers in the device generally
contain random data, even though the RESET signal was asserted.
If parallel programming is used to program one output, that
output is properly programmed, but the rest of the device has a
random program state depending on the internal register content
at power-up. Therefore, when using parallel programming, it is
essential that all outputs be programmed to a desired state after
power-up to ensure that the programming matrix is always in a
known state. From this point, parallel programming can be used
to modify either a single output or multiple outputs at one time.
Similarly, if both CE and UPDATE are taken low after initial
power-up, the random power-up data in the shift register is
programmed into the matrix. Therefore, to prevent programming
the crosspoint into an unknown state, do not apply low logic levels
to both CE and UPDATE after power is initially applied. To eliminate
the possibility of programming the matrix to an unknown state,
after initial power-up, program the full shift register one time to
a desired state using either serial or parallel programming.
To change the programming of an output via parallel programming,
take the SER/PAR and UPDATE pins high, and take the CE pin
low. The CLK signal should be in the high state. Place the 3-bit
address of the output to be programmed on A0 to A2. The first
three data bits (D0 to D2) contain the information that identifies
the input that is programmed to the addressed output. A fourth bit,
reserved, is a reserved enable bit and is internally connected to a
logic high level in parallel programming mode. The fifth data bit
(D3) determines the enabled state of the output. If D3 is low
(output disabled), the data bits on D0 to D2 do not matter.
After the address and data signals are established, they can be
latched into the shift register by pulling the CLK signal low;
however, the matrix is not programmed until the UPDATE signal
is taken low. In this way, it is possible to latch in new data for
several or all of the outputs first via successive negative transitions
of CLK while UPDATE is held high and then have all the new data
take effect when UPDATE goes low. Use this technique when
programming the device for the first time after power-up when
Rev. A | Page 22 of 24
Data Sheet
ADV3228/ADV3229
POWER-ON RESET
When powering up the ADV3228/ADV3229, it is usually desirable
to have the outputs come up in the disabled state. When taken
low, the RESET pin causes all outputs to be in the disabled state.
However, the RESET signal does not reset all registers in the
ADV3228/ADV3229. This is important when operating in the
parallel programming mode. Refer to the Parallel Programming
section for information about programming internal registers
after power-up. Serial programming programs the entire matrix
each time; therefore, no special considerations apply.
Because the data in the shift register is random after power-up,
it should not be used to program the matrix, or the matrix can
enter unknown states. To prevent the matrix from entering
unknown states, do not apply logic low signals to both CE and
UPDATE initially after power-up. Instead, first load the shift
register with the data and then take UPDATE low to program
the device.
of outputs. Nonblocking requires that the programming of a given
input to one or more outputs not restrict the availability of that input
to be a source for any other outputs. Some nonblocking crosspoint
architectures require more than this minimum. In addition, there
are blocking architectures that can be constructed with fewer
devices than this minimum. These systems have connectivity
available on a statistical basis that is determined when designing
the overall system.
The basic concept in constructing larger crosspoint arrays is to
connect inputs in parallel in a horizontal direction and to wire-OR
the outputs together in the vertical direction. The wire-OR
connection can be viewed as a tristate multiplex of the two outputs,
in that only one output is enabled and the other is in a high-Z state.
The meaning of horizontal and vertical can best be understood
by referring to Figure 65, which illustrates this concept for a 32 × 8
crosspoint array that uses four ADV3228 or ADV3229 devices.
ADV3228
8
IN00 TO IN07
8
RTERM
8
The RESET pin has a 20 kΩ pull-up resistor to DVCC that can
be used to create a simple power-up reset circuit. A capacitor from
RESET to ground holds the RESET pin low for a period during
which the rest of the device stabilizes. The low condition causes
all of the outputs to be disabled. The capacitor then charges
through the pull-up resistor to the high state, thereby, allowing
full programming capability of the device.
ADV3228
8
IN08 TO IN15
8
RTERM
ADV3228
8
IN16 TO IN23
8
The 8 × 8 crosspoints come in two versions, depending on
the gain of the analog circuit path. The ADV3228 device is unity
gain and can be used for analog logic switching and other
applications where unity gain is desired. The ADV3228 outputs
have very high impedance when their outputs are disabled.
RTERM
The first consideration in constructing a larger crosspoint is to
determine the minimum number of devices that is required. The 8
× 8 architecture of the ADV3228/ADV3229 contains 64 points,
which is a factor of 16 greater than a 4 × 1 crosspoint (or multiplexer).
The benefits realized in printed circuit board (PCB) area used,
power consumption, and design effort are readily apparent when
compared to using multiples of these smaller 4 × 1 devices.
To obtain the minimum number of required points for a nonblocking crosspoint, multiply the number of inputs by the number
OR
ADV3229
8
ADV3228
8
IN24 TO IN31
8
The ADV3229 can be used for devices that drive a terminated
cable with its outputs. This device has a built-in gain of +2 that
eliminates the need for a gain of +2 buffer to drive a video line. Its
high output disabled impedance minimizes signal degradation
when paralleling additional outputs of other crosspoint devices.
The ADV3228/ADV3229 are high density building blocks for
creating crosspoint arrays of dimensions larger than 8 × 8. Various
features, such as output disable, chip enable, and gain of +1 and
gain of +2 options, are useful for creating larger arrays.
OR
ADV3229
8
GAIN SELECTION
CREATING LARGER CROSSPOINT ARRAYS
OR
ADV3229
RTERM
OR
ADV3229
8
8
OUT00 TO OUT07
09318-007
using parallel programming. In parallel mode, the CLK pin is
level sensitive, whereas in serial mode, it is edge triggered.
Figure 65. A 32 × 8 Nonblocking Crosspoint Switch Array
Each input is uniquely assigned to each of the eight inputs of the
four devices and terminated appropriately; the outputs are wiredOR’ed together. The output from only one wire-OR’ed connection
can be enabled at any given time, and care must be exercised to
minimize load capacitance at the wired-OR’ed connections. The
device programming software must be properly written to prevent
multiple connected outputs from being enabled at the same time.
More expansion options are possible using the ADV3226 and
ADV3227 wideband 16 × 16 arrays, and ADV3224 and ADV3225
16 × 8 arrays. Also available are 32 × 16 arrays in a single package:
AD8104, AD8105, ADV3202, and ADV3203. For a complete
32 × 32 array in a single device, use the AD8117 and AD8118 for
wide bandwidth or the ADV3200 and ADV3201 for less bandwidth.
Rev. A | Page 23 of 24
ADV3228/ADV3229
Data Sheet
OUTLINE DIMENSIONS
10.10
10.00 SQ
9.90
0.60
0.42
0.24
0.60
0.42
0.24
0.30
0.23
0.18
55
54
72
1
PIN 1
INDICATOR
PIN 1
INDICATOR
9.85
9.75 SQ
9.65
0.50
BSC
0.50
0.40
0.30
18
19
37
36
TOP VIEW
BOTTOM VIEW
0.80 MAX
0.65 TYP
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
SEATING
PLANE
0.25 MIN
8.50 REF
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-220-VNND-4
06-15-2012-A
12° MAX
1.00
0.85
0.80
4.70
BSC SQ
EXPOSED
PAD
Figure 66. 72-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
10 mm × 10 mm Body, Very Thin Quad (CP-72-1)
Dimensions shown in millimeters
ORDERING GUIDE
Model1
ADV3228ACPZ
ADV3228-EVALZ
ADV3229ACPZ
ADV3229-EVALZ
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
Package Description
72-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
Evaluation Board
72-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
Evaluation Board
Z = RoHS Compliant Part.
©2010–2016 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D09318-0-1/16(A)
Rev. A | Page 24 of 24
Package Option
CP-72-1
CP-72-1