SiGe AATIAN26 850khz 1a buck regulator Datasheet

EV-103
AAT1152 EVAL
850kHz 1A Buck Regulator
Introduction
The AAT1152 MSOP evaluation board demonstrates performance, along with the suggested size and placement of external components, for the AAT1152 integrated buck regulator. The external components are selected for minimum size and optimum operation up to 1A output current. Please refer to the AAT1152 datasheet
for more details about this product.
Layout
As with all switching power supplies, board layout for the AAT1152 is critical (see Figure 1). Special care has
been taken with the placement of the external components. The input capacitor (C1) placement is critical and
it must be located immediately adjacent to the AAT1152. As shown in Figure 2, the LX node trace has been
routed under C1 in order to facilitate placement of C1 close to the IC. The output voltage feedback trace has
been routed on the portion of backside of the board which has a ground plane on the top side (see Figure 3).
The trace is routed to avoid the LX node and associated noise. Please refer to Table 1 for AAT1152 evaluation board specifications.
R5
100k
U1
AAT1152
VIN+
5
C1
10µF
POK
R1 100
4
R2
3
100k
C2
0.1µF
2
VP
FB
VCC
EN
POK
LX
SGND PGND
1
7
6
8
VO+
R3
R4
10k 1%
L1
4.1µH
C3-C5
3x 22µF
6.3V X5R
VO-
EN
Figure 1: AAT1152 Evaluation Board Schematic.
Specification
Input Voltage
Output Error Voltage
Output Current
Test Conditions
Min
Typ
Max
Units
2.7
3.6
±3
5.5
V
%
A
0
1.0
Table 1: AAT1152 Evaluation Board Specification.
EV-103.2005.07.1.1
1
EV-103
AAT1152 EVAL
850kHz 1A Buck Regulator
Figure 2. AAT1152 Evaluation Board
PCB Top Side.
Figure 3. AAT1152 Evaluation Board
PCB Bottom Side.
Test Equipment
1. 6.0V 2.0A laboratory power supply: HP33401A or equivalent.
2. DC 0A to 1.0A load capable of operation down to 1.0V: Keithley 2400 or equivalent.
When using the Keithley 2400, set the meter to 0V in voltage source mode and set the load current by
varying the current compliance (maximum current) of the meter.
3. DC voltmeter: HP34401A or equivalent.
4. Oscilloscope: Tektronix TDS744A or equivalent.
Setup and Test
A: Load and Line Regulation (see connection diagram in Figure 4)
1. Apply a DC power supply and DC voltmeter across input voltage terminals: VIN+ (positive terminal) and
GND (negative terminal or return).
2. Apply a DC load and DC voltmeter to output terminals: VO+ and GND.
3. Vary the load from 0A to 1.0A and the input voltage from 2.7V to 5.5V while monitoring the output voltage.
4. The output voltage as measured at the output terminals of the evaluation board should not vary by more
than ±3% of the nominal voltage.
B: Short-Circuit and Over-Temperature Protection
1. Raise the input voltage to 5.5V
2. Apply a short from VO+ to GND at the evaluation board terminals.
3. Remove the short and verify that output returns to its initial value.
C: Enable Input
1. Short the enable pin to GND. The output should decay to zero and the Power OK output should go low.
2. Remove the short applied to the enable pin. The output should recover to its initial value and the power
OK output should return to the input voltage.
2
EV-103.2005.07.1.1
EV-103
AAT1152 EVAL
850kHz 1A Buck Regulator
1.500V
Voltmeter
Load
0-1A
Power Supply
3.650V
0.147A
3.600V
Voltmeter
Figure 4: AAT1152 Connection Diagram.
Component
U1
U1
U1
U1
C3, C4, C5
C1
C2
R1
R2
L1
Part Number
Description
AAT1152IKS-1.0-T1
AAT1152IKS-1.8-T1
AAT1152IKS-2.5-T1
AAT1152IKS-3.3-T1
GRM21BR60J226KE19
GRM319R60J106KE01
GRM155R61A104KA01
Chip Resistor
Chip Resistor
CDRH5D18-4R1
1.0V 1A Buck Converter
1.8V 1A Buck Converter
2.5V 1A Buck Converter
3.3V 1A Buck Converter
22µF, 6.3V, X5R, 10%, 0805
10µF, 6.3V, X5R, 10%, 1206
0.1µF, 25V, X5R, 10%, 0402
100kΩ, 5%, 1/16W; 0402
100kΩ, 5%, 1/16W; 0402
4.1µH, 57mΩ, 1.95A Shielded
AAT1152KS-1.0-T1
Table 3, 1%, 1/16W; 0402
AAT1152IKS-1.8-T1
0Ω, 0402
AAT1152IKS-2.5-T1
0Ω, 0402
AAT1152IKS-3.3-T1
0Ω, 0402
10kΩ, 1%, 1/16W; 0402 (required with
AAT1152IKS-1.0-T1 when output is >1.0V only)
R3
Chip Resistor
R4
Chip Resistor
Manufacturer
AnalogicTech
AnalogicTech
AnalogicTech
AnalogicTech
MuRata
MuRata
MuRata
Vishay
Vishay
Sumida
Vishay
Vishay
Vishay
Vishay
Vishay
Table 2: AAT1152 EVAL Bill of Materials.
EV-103.2005.07.1.1
3
EV-103
AAT1152 EVAL
850kHz 1A Buck Regulator
Output Voltage
For an adjustable output, set R4 to 10kΩ and select R3 according to Table 3 using the AAT1152IKS-1.0-T1.
VO (V)
Ω)
R3 (kΩ
1.0
1.1
1.2
1.25
1.3
1.4
1.5
1.6
1.7
1.8
1.85
1.9
2.0
2.1
2.2
2.3
2.4
2.5
3.3
0.00 (short)
1.00
2.00
2.55
3.01
4.02
4.99
6.04
6.98
8.06
8.45
9.09
10.0
11.0
12.1
13.0
14.0
15.0
23.2
Ω).
Table 3: Resistor Selection for Adjustable Output Voltage (R4 = 10kΩ
AnalogicTech cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in an AnalogicTech product. No circuit patent licenses, copyrights, mask work
rights, or other intellectual property rights are implied.
AnalogicTech reserves the right to make changes to their products or specifications or to discontinue any product or service without notice, and advise customers to obtain the latest
version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale
supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability.
AnalogicTech warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with AnalogicTech’s standard warranty. Testing and
other quality control techniques are utilized to the extent AnalogicTech deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed.
Advanced Analogic Technologies, Inc.
830 E. Arques Avenue, Sunnyvale, CA 94085
Phone (408) 737-4600
Fax (408) 737-4611
4
EV-103.2005.07.1.1
Similar pages