TI1 DAC5652AIPFBG4 Dual, 10-bit 275 msps digital-to-analog converter Datasheet

DAC5652A
www.ti.com
SLAS535D – SEPTEMBER 2007 – REVISED AUGUST 2012
DUAL, 10-BIT 275 MSPS DIGITAL-TO-ANALOG CONVERTER
Check for Samples: DAC5652A
FEATURES
APPLICATIONS
•
•
1
•
•
•
•
•
•
•
•
•
•
10-Bit Dual Transmit Digital-to-Analog
Converter (DAC)
275 MSPS Update Rate
Single Supply: 3.0 V to 3.6 V
High Spurious-Free Dynamic Range (SFDR):
80 dBc at 5 MHz
High Third-Order Two-Tone Intermodulation
(IMD3): 78 dBc at 15.1 MHz and 16.1 MHz
Independent or Single Resistor Gain Control
Dual or Interleaved Data
On-Chip 1.2-V Reference
Low Power: 290 mW
Power-Down Mode: 9 mW
Package: 48-Pin Thin-Quad Flat Pack (TQFP)
•
•
•
•
Cellular Base Transceiver Station Transmit
Channel
– CDMA: W-CDMA, CDMA2000, IS-95
– TDMA: GSM, IS-136, EDGE/UWC-136
Medical/Test Instrumentation
Arbitrary Waveform Generators (ARB)
Direct Digital Synthesis (DDS)
Cable Modem Termination System (CMTS)
DESCRIPTION
The DAC5652A is a monolithic, dual-channel, 10-bit, high-speed DAC with on-chip voltage reference.
Operating with update rates of up to 275 MSPS, the DAC5652A offers exceptional dynamic performance, tightgain, and offset matching characteristics that make it suitable in either I/Q baseband or direct IF communication
applications.
Each DAC has a high-impedance, differential-current output, suitable for single-ended or differential analogoutput configurations. External resistors allow scaling of the full-scale output current for each DAC separately or
together, typically between 2 mA and 20 mA. An accurate on-chip voltage reference is temperature-compensated
and delivers a stable 1.2-V reference voltage. Optionally, an external reference may be used.
The DAC5652A has two, 10-bit, parallel input ports with separate clocks and data latches. For flexibility, the
DAC5652A also supports multiplexed data for each DAC on one port when operating in the interleaved mode.
The DAC5652A has been specifically designed for a differential transformer-coupled output with a 50-Ω doublyterminated load. For a 20-mA full-scale output current, both a 4:1 impedance ratio (resulting in an output power
of 4 dBm) and 1:1 impedance ratio transformer (–2 dBm output power) are supported.
The DAC5652A is available in a 48-pin TQFP package. Pin compatibility between family members provides 10bit (DAC5652A), 12-bit (DAC5662), and 14-bit (DAC5672) resolution. Furthermore, the DAC5652A is pin
compatible to the DAC2900 and AD9763 dual DACs. The device is characterized for operation over the industrial
temperature range of –40°C to 85°C.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2007–2012, Texas Instruments Incorporated
DAC5652A
SLAS535D – SEPTEMBER 2007 – REVISED AUGUST 2012
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
FUNCTIONAL BLOCK DIAGRAM
WRTB
WRTA
CLKB
CLKA
DEMUX
IOUTA1
Latch A
10−b DAC
IOUTA2
DA[9:0]
BIASJ_A
IOUTB1
Latch B
DB[9:0]
10−b DAC
IOUTB2
MODE
BIASJ_B
GSET
1.2 V Reference
EXTIO
SLEEP
DVDD
DGND
AVDD
AGND
AVAILABLE OPTIONS
PACKAGED DEVICES
48-Pin TQFP
TA
DAC5652AIPFB
–40°C to 85°C
DAC5652AIPFBR
THERMAL INFORMATION
THERMAL METRIC (1) (2)
DAC5652A
PFB (48 PINS)
θJA
Junction-to-ambient thermal resistance
65.3
θJCtop
Junction-to-case (top) thermal resistance
16.4
θJB
Junction-to-board thermal resistance
28.6
ψJT
Junction-to-top characterization parameter
0.4
ψJB
Junction-to-board characterization parameter
28.4
θJCbot
Junction-to-case (bottom) thermal resistance
n/a
(1)
(2)
2
UNITS
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
For thermal estimates of this device based on PCB copper area, see the TI PCB Thermal Calculator.
Submit Documentation Feedback
Copyright © 2007–2012, Texas Instruments Incorporated
Product Folder Links: DAC5652A
DAC5652A
www.ti.com
SLAS535D – SEPTEMBER 2007 – REVISED AUGUST 2012
MODE
AVDD
IOUTA1
IOUTA2
BIASJ_A
EXTIO
GSET
BIASJ_B
IOUTB2
IOUTB1
AGND
SLEEP
DEVICE INFORMATION
1
48 47 46 45 44 43 42 41 40 39 38 37
36
2
35
3
34
4
33
5
32
Top View
48-Pin TQFP
PFB Package
6
7
31
30
8
29
9
28
10
27
11
26
25
12
13 14 15 16 17 18 19 20 21 22 23 24
NC
NC
NC
NC
DB0 (LSB)
DB1
DB2
DB3
DB4
DB5
DB6
DB7
NC
NC
DGND
DVDD
WRTA/WRTIQ
CLKA/CLKIQ
CLKB/RESETIQ
WRTB/SELECTIQ
DGND
DVDD
DB9 (MSB)
DB8
DA9 (MSB)
DA8
DA7
DA6
DA5
DA4
DA3
DA2
DA1
DA0 (LSB)
NC
NC
PIN FUNCTIONS
PIN
I/O
DESCRIPTION
NAME
NO.
AGND
38
I
Analog ground
AVDD
47
I
Analog supply voltage
BIASJ_A
44
O
Full-scale output current bias for DACA
BIASJ_B
41
O
Full-scale output current bias for DACB
CLKA/CLKIQ
18
I
Clock input for DACA, CLKIQ in interleaved mode
CLKB/RESETIQ
19
I
Clock input for DACB, RESETIQ in interleaved mode
DA[9:0]
1-10
I
Data port A. DA9 is MSB and DA0 is LSB. Internal pulldown.
DB[9:0]
23-32
I
Data port B. DB9 is MSB and DB0 is LSB. Internal pulldown.
DGND
15, 21
I
Digital ground
DVDD
16, 22
I
Digital supply voltage
EXTIO
43
I/O
GSET
42
I
Gain-setting mode: H – 1 resistor, L – 2 resistors. Internal pullup.
IOUTA1
46
O
DACA current output. Full-scale with all bits of DA high.
IOUTA2
45
O
DACA complementary current output. Full-scale with all bits of DA low.
IOUTB1
39
O
DACB current output. Full-scale with all bits of DB high.
IOUTB2
40
O
DACB complementary current output. Full-scale with all bits of DB low.
MODE
48
I
Mode Select: H – Dual Bus, L – Interleaved. Internal pullup.
11-14, 33-36
-
Factory use only. Pins must be connected to DGND or left unconnected.
SLEEP
37
I
Sleep function control input: H – DAC in power-down mode, L – DAC in operating mode.
Internal pulldown.
WRTA/WRTIQ
17
I
Input write signal for PORT A (WRTIQ in interleaving mode)
WRTB/SELECTIQ
20
I
Input write signal for PORT B (SELECTIQ in interleaving mode)
NC
Internal reference output (bypass with 0.1 μF to AGND) or external reference input
Submit Documentation Feedback
Copyright © 2007–2012, Texas Instruments Incorporated
Product Folder Links: DAC5652A
3
DAC5652A
SLAS535D – SEPTEMBER 2007 – REVISED AUGUST 2012
www.ti.com
ABSOLUTE MAXIMUM RATINGS
over TA (unless otherwise noted) (1)
UNIT
AVDD
Supply voltage range
(2)
–0.5 V to 4 V
DVDD (3)
–0.5 V to 4 V
Voltage between AGND and DGND
–0.5 V to 0.5 V
Voltage between AVDD and DVDD
–4 V to 4 V
DA[9:0] and DB[9:0]
(3)
–0.5 V to DVDD + 0.5 V
MODE, SLEEP, CLKA, CLKB, WRTA, WRTB (3)
Supply voltage range
–0.5 V to DVDD + 0.5 V
IOUTA1, IOUTA2, IOUTB1, IOUTB2 (2)
EXTIO, BIASJ_A, BIASJ_B, GSET
–1 V to AVDD + 0.5 V
(2)
–0.5 V to AVDD + 0.5 V
Peak input current (any input)
20 mA
Peak total input current (all inputs)
–30 mA
Operating free-air temperature range
–40°C to 85°C
Storage temperature range
–65°C to 150°C
(1)
(2)
(3)
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings
only and functional operation of these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
Measured with respect to AGND.
Measured with respect to DGND.
ELECTRICAL CHARACTERISTICS
over TA, AVDD = DVDD = 3.3 V, I(OUTFS) = 20 mA, independent gain set mode (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
DC Specifications
Resolution
DC Accuracy
10
Bits
(1)
INL
Integral nonlinearity
DNL
Differential nonlinearity
1 LSB = I(OUTFS)/210, TMIN to TMAX
–1
±0.25
1
LSB
–0.5
±0.16
0.5
LSB
Analog Output
Offset error
Midscale value (internal reference)
±0.05
%FSR
Offset mismatch
Midscale value (internal reference)
±0.03
%FSR
Gain error
With internal reference
±0.75
%FSR
Minimum full-scale output current
(2)
2
Maximum full-scale output current (2)
Gain mismatch
With internal reference
Output voltage compliance range (3)
RO
Output resistance
CO
Output capacitance
mA
20
–2
0.2
–1
mA
2
1.25
%FSR
V
300
kΩ
5
pF
Reference Output
Reference voltage
1.14
Reference output current (4)
1.2
1.26
100
V
nA
Reference Input
V(EXTIO)
Input voltage
RI
Input resistance
0.1
Small signal bandwidth
(1)
(2)
(3)
(4)
4
1.25
V
1
MΩ
300
kHz
Measured differentially through 50 Ω to AGND.
Nominal full-scale current, I(OUTFS), equals 32x the I(BIAS) current.
The lower limit of the output compliance is determined by the CMOS process. Exceeding this limit may result in transistor breakdown,
resulting in reduced reliability of the DAC5652A device. The upper limit of the output compliance is determined by the load resistors and
full-scale output current. Exceeding the upper limit adversely affects distortion performance and integral nonlinearity.
Use an external buffer amplifier with high-impedance input to drive any external load.
Submit Documentation Feedback
Copyright © 2007–2012, Texas Instruments Incorporated
Product Folder Links: DAC5652A
DAC5652A
www.ti.com
SLAS535D – SEPTEMBER 2007 – REVISED AUGUST 2012
ELECTRICAL CHARACTERISTICS (continued)
over TA, AVDD = DVDD = 3.3 V, I(OUTFS) = 20 mA, independent gain set mode (unless otherwise noted)
PARAMETER
CI
TEST CONDITIONS
MIN
Input capacitance
TYP
MAX
UNIT
100
pF
Temperature Coefficients
Offset drift
With external reference
Gain drift
With internal reference
Reference voltage drift
2
ppm of
FSR/°C
±20
ppm of
FSR/°C
±40
ppm of
FSR/°C
±20
ppm/°C
ELECTRICAL CHARACTERISTICS
over TA, AVDD = DVDD = 3.3 V, I(OUTFS) = 20 mA, fDATA = 200 MSPS, fOUT = 1 MHz, independent gain set mode (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Power Supply
AVDD
Analog supply voltage
3
3.3
3.6
V
DVDD
Digital supply voltage
3
3.3
3.6
V
Including output current through load
resistor
75
90
Sleep mode with clock
2.5
Sleep mode without clock
2.5
I(AVDD)
I(DVDD)
Supply current, analog
Supply current, digital
Sleep mode with clock
Sleep mode without clock
12
20
11.3
18
mA
0.6
290
Power dissipation
mA
Sleep mode with clock
360
45.5
Sleep mode without clock
9.2
fDATA = 275 MSPS, fOUT = 20 MHz
310
mW
APSRR
Analog power supply rejection ratio
–0.2
–0.01
0.2
%FSR/V
DPSRR
Digital power supply rejection ratio
–0.2
0
0.2
%FSR/V
TA
Operating free-air temperature
–40
85
°C
Submit Documentation Feedback
Copyright © 2007–2012, Texas Instruments Incorporated
Product Folder Links: DAC5652A
5
DAC5652A
SLAS535D – SEPTEMBER 2007 – REVISED AUGUST 2012
www.ti.com
ELECTRICAL CHARACTERISTICS
AC specifications over TA, AVDD = DVDD = 3.3 V, I(OUTFS) = 20 mA, independent gain set mode, differential 1:1 impedance
ratio transformer coupled output, 50-Ω doubly terminated load (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Analog Output
fclk
Maximum output update
rate (1)
ts
Output settling time to 0.1%
(DAC)
tr
tf
275
20
ns
Output rise time 10% to 90%
(OUT)
1.4
ns
Output fall time 90% to 10%
(OUT)
1.5
ns
Output noise
Mid-scale transition
MSPS
I(OUTFS) = 20 mA
55
I(OUTFS) = 2 mA
30
1st Nyquist zone, TA = 25°C,
fDATA = 50 MSPS, fOUT = 1 MHz, I(OUTFS) = 0 dB
79
1st Nyquist zone, TA = 25°C,
fDATA = 50 MSPS, fOUT = 1 MHz, I(OUTFS) = –6 dB
78
1st Nyquist zone, TA = 25°C,
fDATA = 50 MSPS, fOUT = 1 MHz, I(OUTFS) = –12 dB
73
1st Nyquist zone, TA = 25°C,
fDATA = 100 MSPS, fOUT = 5 MHz, I(OUTFS) = 0 dB
80
1st Nyquist zone, TA = 25°C,
fDATA = 100 MSPS, fOUT = 20 MHz, I(OUTFS) = 0 dB
76
pA/√Hz
AC Linearity
SFDR
Spurious-free dynamic range
1st Nyquist zone, TMIN to TMAX,
fDATA = 200 MSPS, fOUT = 20 MHz, I(OUTFS) = 0 dB
SNR
IMD3
IMD
Signal-to-noise ratio
Third-order two-tone
intermodulation
Four-tone intermodulation
Channel isolation
(1)
6
dBc
61
70
1st Nyquist zone, TA = 25°C,
fDATA = 200 MSPS, fOUT = 41 MHz, I(OUTFS) = 0 dB
67
1st Nyquist zone, TA = 25°C,
fDATA = 275 MSPS, fOUT = 20 MHz
70
1st Nyquist zone, TA = 25°C,
fDATA = 100 MSPS, fOUT = 5 MHz, I(OUTFS) = 0 dB
63
1st Nyquist zone, TA = 25°C,
fDATA = 160 MSPS, fOUT = 20 MHz, I(OUTFS) = 0 dB
62
Each tone at –6 dBFS, TA = 25°C,
fDATA = 200 MSPS, fOUT = 45.4 MHz and 46.4 MHz
61
Each tone at –6 dBFS, TA = 25°C,
fDATA = 100 MSPS, fOUT = 15.1 MHz and 16.1 MHz
78
Each tone at –12 dBFS, TA = 25°C
fDATA = 100 MSPS, fOUT = 15.6, 15.8, 16.2, and
16.4 MHz
76
Each tone at –12 dBFS, TA = 25°C
fDATA = 165 MSPS, fOUT = 19.0, 19.1, 19.3, and
19.4 MHz
55
Each tone at –12 dBFS, TA = 25°C
fDATA = 165 MSPS, fOUT = 68.8, 69.6, 71.2, and
72.0 MHz
70
TA = 25°C, fDATA = 165 MSPS
fOUT (CH1) = 20 MHz, fOUT (CH2) = 21 MHz
90
dB
dB
dBc
dBc
dBc
Specified by design and bench characterization. Not production tested.
Submit Documentation Feedback
Copyright © 2007–2012, Texas Instruments Incorporated
Product Folder Links: DAC5652A
DAC5652A
www.ti.com
SLAS535D – SEPTEMBER 2007 – REVISED AUGUST 2012
ELECTRICAL CHARACTERISTICS
Digital specifications over TA, AVDD = DVDD = 3.3 V, I(OUTFS) = 20 mA (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Digital Input
VIH
High-level input voltage
VIL
Low-level input voltage
2
V
IIH
High-level input current
±50
µA
IIL
Low-level input current
±10
µA
IIH(GSET)
High-level input current, GSET pin
7
µA
IIL(GSET)
Low-level input current, GSET pin
–80
µA
IIH(MODE)
High-level input current, MODE pin
–30
µA
IIL(MODE)
Low-level input current, MODE pin
–80
µA
CI
Input capacitance
5
pF
0.8
V
SWITCHING CHARACTERISTICS
Digital specifications over TA, AVDD = DVDD = 3.3 V, I(OUTFS) = 20 mA (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Timing - Dual Bus Mode
tsu
Input setup time
1
th
Input hold time
1
tLPH
Input clock pulse high time
tLAT
Clock latency (WRTA/B to outputs)
tPD
Propagation delay time
ns
ns
1
ns
4
4
clk
1.5
ns
0.5
ns
Timing - Single Bus Interleaved Mode
tsu
Input setup time
th
Input hold time
tLAT
Clock latency (WRTA/B to outputs)
tPD
Propagation delay time
0.5
ns
4
4
1.5
clk
ns
TYPICAL CHARACTERISTICS
INL − Integral Nonlinearity Error − LSB
INTEGRAL NONLINEARITY
vs
INPUT CODE
0.5
0.4
0.3
0.2
0.1
0.0
−0.1
−0.2
−0.3
−0.4
−0.5
0
100
200
300
400
500
600
Input Code
700
800
900
1000
G001
Figure 1.
Submit Documentation Feedback
Copyright © 2007–2012, Texas Instruments Incorporated
Product Folder Links: DAC5652A
7
DAC5652A
SLAS535D – SEPTEMBER 2007 – REVISED AUGUST 2012
www.ti.com
TYPICAL CHARACTERISTICS (continued)
DNL − Differential Nonlinearity Error − LSB
DIFFERENTIAL NONLINEARITY
vs
INPUT CODE
0.25
0.20
0.15
0.10
0.05
0.00
−0.05
−0.10
−0.15
−0.20
−0.25
0
100
200
300
400
500
600
700
800
900
1000
Input Code
G002
Figure 2.
SPURIOUS-FREE DYNAMIC RANGE
vs
OUTPUT FREQUENCY
SPURIOUS-FREE DYNAMIC RANGE
vs
OUTPUT FREQUENCY
100
SFDR − Spurious-Free Dynamic Range − dBc
SFDR − Spurious-Free Dynamic Range − dBc
100
fdata = 52 MSPS
Dual Bus Mode
95
90
85
−6 dBfS
0 dBfS
80
75
−12 dBfS
70
65
60
fdata = 78 MSPS
Dual Bus Mode
95
90
85
−6 dBfS
80
75
−12 dBfS
70
0 dBfS
65
60
0
4
8
12
16
fout − Output Frequency − MHz
20
0
G003
Figure 3.
8
5
10
15
20
fout − Output Frequency − MHz
25
30
G004
Figure 4.
Submit Documentation Feedback
Copyright © 2007–2012, Texas Instruments Incorporated
Product Folder Links: DAC5652A
DAC5652A
www.ti.com
SLAS535D – SEPTEMBER 2007 – REVISED AUGUST 2012
TYPICAL CHARACTERISTICS (continued)
SPURIOUS-FREE DYNAMIC RANGE
vs
OUTPUT FREQUENCY
SPURIOUS-FREE DYNAMIC RANGE
vs
OUTPUT FREQUENCY
100
SFDR − Spurious-Free Dynamic Range − dBc
SFDR − Spurious-Free Dynamic Range − dBc
100
fdata = 100 MSPS
Dual Bus Mode
95
90
85
−6 dBfS
80
0 dBfS
75
−12 dBfS
70
65
60
fdata = 165 MSPS
Dual Bus Mode
95
90
85
80
0 dBfS
−6 dBfS
75
70
−12 dBfS
65
60
0
5
10
15
20
25
30
fout − Output Frequency − MHz
35
0
5
10 15 20 25 30 35 40 45 50 55 60
fout − Output Frequency − MHz
G005
Figure 5.
SINGLE-TONE SPECTRUM
SINGLE-TONE SPECTRUM
0
0
fdata = 165 MSPS
fOUT = 30.1 MHz
Dual Bus Mode
fdata = 78 MSPS
fOUT = 15 MHz
Dual Bus Mode
−20
Power − dBm
Power − dBm
−20
−40
−60
−40
−60
−80
−80
−100
0.0
G006
Figure 6.
7.8
15.6
23.4
31.2
39.0
−100
0.0
16.5
33.0
49.5
66.0
82.5
f − Frequency − MHz
f − Frequency − MHz
G008
G007
Figure 7.
Figure 8.
Submit Documentation Feedback
Copyright © 2007–2012, Texas Instruments Incorporated
Product Folder Links: DAC5652A
9
DAC5652A
SLAS535D – SEPTEMBER 2007 – REVISED AUGUST 2012
www.ti.com
TYPICAL CHARACTERISTICS (continued)
TWO-TONE IMD3
vs
OUTPUT FREQUENCY
TWO-TONE IMD3
vs
OUTPUT FREQUENCY
95
100
95
90
Two-Tone IMD3 − dBc
Two-Tone IMD3 − dBc
90
85
80
75
70
85
80
75
70
65
60
fdata = 78 MSPS
Dual Bus Mode
fout2 = fout1 + 1 MHz
65
60
50
0
5
10
15
20
25
30
fout1 − Output Frequency − MHz
−10
35
0
20
30
G009
Figure 10.
TWO-TONE SPECTRUM
TWO-TONE SPECTRUM
50
G010
fdata = 165 MSPS
−10 fout1 = 30.1 MHz
fout2 = 31.1 MHz
Dual Bus Mode
Power − dBm
−30
−50
−70
−90
−50
−70
−90
19.5
20.0
20.5
21.0
21.5
−110
29.0
22.0
f − Frequency − MHz
29.5
30.0
30.5
31.0
31.5
32.0
f − Frequency − MHz
G011
Figure 11.
10
40
Figure 9.
fdata = 78 MSPS
fout1 = 20.1 MHz
fout2 = 21.1 MHz
Dual Bus Mode
−110
19.0
10
fout1 − Output Frequency − MHz
−30
Power − dBm
fdata = 165 MSPS
Dual Bus Mode
fout2 = fout1 + 1 MHz
55
G012
Figure 12.
Submit Documentation Feedback
Copyright © 2007–2012, Texas Instruments Incorporated
Product Folder Links: DAC5652A
DAC5652A
www.ti.com
SLAS535D – SEPTEMBER 2007 – REVISED AUGUST 2012
Digital Inputs and Timing
Digital Inputs
The data input ports of the DAC5652A accept a standard positive coding with data bits DA9 and DB9 being the
most significant bits (MSB). The converter outputs support a clock rate of up to 275 MSPS. The best
performance is typically achieved with a symmetric duty cycle for write and clock; however, the duty cycle may
vary as long as the timing specifications are met. Similarly, the setup and hold times may be chosen within their
specified limits.
All digital inputs of the DAC5652A are CMOS compatible. Figure 13 and Figure 14 show schematics of the
equivalent CMOS digital inputs of the DAC5652A. The pullup and pulldown circuitry is approximately equivalent
to 100kΩ. The 10-bit digital data input follows the offset positive binary coding scheme. The DAC5652A is
designed to operate with a digital supply (DVDD) of 3 V to 3.6 V.
DVDD
DA[9:0]
DB[9:0]
SLEEP
CLKA/B
WRTA/B
400W
Internal
Digital In
100kW
DGND
Figure 13. CMOS/TTL Digital Equivalent Input With Internal Pulldown Resistor
DVDD
100kW
GSET
MODE
400W
Internal
Digital In
DGND
Figure 14. CMOS/TTL Digital Equivalent Input With Internal Pullup Resistor
Input Interfaces
The DAC5652A features two operating modes selected by the MODE pin, as shown in Table 1.
• For dual-bus input mode, the device essentially consists of two separate DACs. Each DAC has its own
separate data input bus, clock input, and data write signal (data latch-in).
• In single-bus interleaved mode, the data must be presented interleaved at the A-channel input bus. The Bchannel input bus is not used in this mode. The clock and write input are now shared by both DACs.
Submit Documentation Feedback
Copyright © 2007–2012, Texas Instruments Incorporated
Product Folder Links: DAC5652A
11
DAC5652A
SLAS535D – SEPTEMBER 2007 – REVISED AUGUST 2012
www.ti.com
Table 1. Operating Modes
MODE Pin
MODE pin connected to DGND
MODE pin connected to DVDD
Bus input
Single-bus interleaved mode, clock and write input equal for both DACs
Dual-bus mode, DACs operate independently
Dual-Bus Data Interface and Timing
In dual-bus mode, the MODE pin is connected to DVDD. The two converter channels within the DAC5652A
consist of two independent, 10-bit, parallel data ports. Each DAC channel is controlled by its own set of write
(WRTA, WRTB) and clock (CLKA, CLKB) lines. The WRTA/B lines control the channel input latches and the
CLKA/B lines control the DAC latches. The data is first loaded into the input latch by a rising edge of the
WRTA/B line.
The internal data transfer requires a correct sequence of write and clock inputs, since essentially two clock
domains having equal periods (but possibly different phases) are input to the DAC5652A. This is defined by a
minimum requirement of the time between the rising edge of the clock and the rising edge of the write inputs.
This essentially implies that the rising edge of CLKA/B must occur at the same time or before the rising edge of
the WRTA/B signal. A minimum delay of 2 ns must be maintained if the rising edge of the clock occurs after the
rising edge of the write. Note that these conditions are satisfied when the clock and write inputs are connected
externally. Note that all specifications were measured with the WRTA/B and CLKA/B lines connected together.
DA[9:0]/DB[9:0]
Valid Data
tsu
th
tLPH
WRTA/WRTB
CLKA/CLKB
ts
tPD
tLAT
IOUT
or
IOUT
Figure 15. Dual-Bus Mode Operation
Single-Bus Interleaved Data Interface and Timing
In single-bus interleaved mode, the MODE pin is connected to DGND. Figure 16 shows the timing diagram. In
interleaved mode, the A- and B-channels share the write input (WRTIQ) and update clock (CLKIQ and internal
CLKDACIQ). Multiplexing logic directs the input word at the A-channel input bus to either the A-channel input
latch (SELECTIQ is high) or to the B-channel input latch (SELECTIQ is low). When SELECTIQ is high, the data
value in the B-channel latch is retained by presenting the latch output data to its input again. When SELECTIQ is
low, the data value in the A-channel latch is retained by presenting the latch output data to its input.
In interleaved mode, the A-channel input data rate is twice the update rate of the DAC core. As in dual-bus
mode, it is important to maintain a correct sequence of write and clock inputs. The edge-triggered flip-flops latch
the A- and B-channel input words on the rising edge of the write input (WRTIQ). This data is presented to the Aand B-DAC latches on the following falling edge of the write inputs. The DAC5652A clock input is divided by a
factor of two before it is presented to the DAC latches.
12
Submit Documentation Feedback
Copyright © 2007–2012, Texas Instruments Incorporated
Product Folder Links: DAC5652A
DAC5652A
www.ti.com
SLAS535D – SEPTEMBER 2007 – REVISED AUGUST 2012
Correct pairing of the A- and B-channel data is done by RESETIQ. In interleaved mode, the clock input CLKIQ is
divided by two, which would translate to a non-deterministic relation between the rising edges of the CLKIQ and
CLKDACIQ. RESETIQ ensures, however, that the correct position of the rising edge of CLKDACIQ with respect
to the data at the input of the DAC latch is determined. CLKDACIQ is disabled (low) when RESETIQ is high.
DA[9:0]
Valid Data
tsu
th
SELECTIQ
WRTIQ
CLKIQ
RESETIQ
ts
tPD
tLAT
IOUT
or
IOUT
Figure 16. Single-Bus Interleaved Mode Operation
Submit Documentation Feedback
Copyright © 2007–2012, Texas Instruments Incorporated
Product Folder Links: DAC5652A
13
DAC5652A
SLAS535D – SEPTEMBER 2007 – REVISED AUGUST 2012
www.ti.com
APPLICATION INFORMATION
Theory of Operation
The architecture of the DAC5652A uses a current steering technique to enable fast switching and high update
rate. The core element within the monolithic DAC is an array of segmented current sources that are designed to
deliver a full-scale output current of up to 20 mA. An internal decoder addresses the differential current switches
each time the DAC is updated and a corresponding output current is formed by steering all currents to either
output summing node, IOUT1 or IOUT2. The complementary outputs deliver a differential output signal, which
improves the dynamic performance through reduction of even-order harmonics, common-mode signals (noise),
and double the peak-to-peak output signal swing by a factor of two, as compared to single-ended operation.
The segmented architecture results in a significant reduction of the glitch energy and improves the dynamic
performance (SFDR) and DNL. The current outputs maintain a very high output impedance of greater
than 300 kΩ.
When pin 42 (GSET) is high (simultaneous gain set mode), the full-scale output current for both DACs is
determined by the ratio of the internal reference voltage (1.2 V) and an external resistor (RSET) connected to
BIASJ_A. When GSET is low (independent gain set mode), the full-scale output current for each DAC is
determined by the ratio of the internal reference voltage (1.2 V) and separate external resistors (RSET) connected
to BIASJ_A and BIASJ_B. The resulting IREF is internally multiplied by a factor of 32 to produce an effective DAC
output current that can range from 2 mA to 20 mA, depending on the value of RSET.
The DAC5652A is split into a digital and an analog portion, each of which is powered through its own supply pin.
The digital section includes edge-triggered input latches and the decoder logic, while the analog section
comprises both the current source array with its associated switches, and the reference circuitry.
DAC Transfer Function
Each of the DACs in the DAC5652A has a set of complementary current outputs, IOUT1 and IOUT2. The fullscale output current, IOUTFS, is the summation of the two complementary output currents:
I
+I
)I
OUTFS
OUT1
OUT2
(1)
The individual output currents depend on the DAC code and can be expressed as:
I
I
OUT1
+I
OUTFS
OUT2
+I
OUTFS
Ǔ
ǒCode
1024
* CodeǓ
ǒ10231024
(2)
(3)
where Code is the decimal representation of the DAC data input word. Additionally, IOUTFS is a function of the
reference current IREF, which is determined by the reference voltage and the external setting resistor (RSET).
V
REF
I
+ 32 I
+ 32
OUTFS
REF
R
SET
(4)
In most cases, the complementary outputs drive resistive loads or a terminated transformer. A signal voltage
develops at each output according to:
V
+I
R
OUT1
OUT1
LOAD
(5)
V
+I
R
OUT2
OUT2
LOAD
(6)
The value of the load resistance is limited by the output compliance specification of the DAC5652A. To maintain
specified linearity performance, the voltage for IOUT1 and IOUT2 must not exceed the maximum allowable
compliance range.
14
Submit Documentation Feedback
Copyright © 2007–2012, Texas Instruments Incorporated
Product Folder Links: DAC5652A
DAC5652A
www.ti.com
SLAS535D – SEPTEMBER 2007 – REVISED AUGUST 2012
The total differential output voltage is:
V
+V
*V
OUTDIFF
OUT1
OUT2
(2 Code * 1023)
V
+
OUTDIFF
1024
(7)
I
OUTFS
R
LOAD
(8)
Analog Outputs
The DAC5652A provides two complementary current outputs, IOUT1 and IOUT2. The simplified circuit of the
analog output stage representing the differential topology is shown in Figure 17. The output impedance of IOUT1
and IOUT2 results from the parallel combination of the differential switches, along with the current sources and
associated parasitic capacitances.
AVDD
S(1)
IOUT1
RLOAD
S(1)C
IOUT2
S(2)
S(2)C
S(N)
S(N)C
Current Source Array
RLOAD
Figure 17. Analog Outputs
The signal voltage swing that may develop at the two outputs, IOUT1 and IOUT2, is limited by a negative and
positive compliance. The negative limit of –1 V is given by the breakdown voltage of the CMOS process and
exceeding it compromises the reliability of the DAC5652A (or even causes permanent damage). With the fullscale output set to 20 mA, the positive compliance equals 1.2 V. Note that the compliance range decreases to
about 1 V for a selected output current of I(OUTFS) = 2 mA. Care must be taken that the configuration of
DAC5652A does not exceed the compliance range to avoid degradation of the distortion performance and
integral linearity.
Best distortion performance is typically achieved with the maximum full-scale output signal limited to
approximately 0.5 VPP. This is the case for a 50-Ω doubly-terminated load and a 20-mA full-scale output current.
A variety of loads can be adapted to the output of the DAC5652A by selecting a suitable transformer while
maintaining optimum voltage levels at IOUT1 and IOUT2. Furthermore, using the differential output configuration
in combination with a transformer is instrumental for achieving excellent distortion performance. Common-mode
errors, such as even-order harmonics or noise, can be substantially reduced. This is particularly the case with
high output frequencies.
For those applications requiring the optimum distortion and noise performance, it is recommended to select a fullscale output of 20 mA. A lower full-scale range of 2 mA may be considered for applications that require low
power consumption, but can tolerate a slight reduction in performance level.
Output Configurations
The current outputs of the DAC5652A allow for a variety of configurations. As mentioned previously, utilizing the
converter’s differential outputs yield the best dynamic performance. Such a differential output circuit may consist
of an RF transformer or a differential amplifier configuration. The transformer configuration is ideal for most
applications with ac coupling, while op amps are suitable for a dc-coupled configuration.
Submit Documentation Feedback
Copyright © 2007–2012, Texas Instruments Incorporated
Product Folder Links: DAC5652A
15
DAC5652A
SLAS535D – SEPTEMBER 2007 – REVISED AUGUST 2012
www.ti.com
The single-ended configuration may be considered for applications requiring a unipolar output voltage.
Connecting a resistor from either one of the outputs to ground converts the output current into a groundreferenced voltage signal. To improve on the dc linearity by maintaining a virtual ground, an I-to-V or op-amp
configuration may be considered.
Differential With Transformer
Using an RF transformer provides a convenient way of converting the differential output signal into a singleended signal while achieving excellent dynamic performance. The appropriate transformer must be carefully
selected based on the output frequency spectrum and impedance requirements.
The differential transformer configuration has the benefit of significantly reducing common-mode signals, thus
improving the dynamic performance over a wide range of frequencies. Furthermore, by selecting a suitable
impedance ratio (winding ratio) the transformer can provide optimum impedance matching while controlling the
compliance voltage for the converter outputs.
Figure 18 and Figure 19 show 50-Ω doubly-terminated transformer configurations with 1:1 and 4:1 impedance
ratios, respectively. Note that the center tap of the primary input of the transformer has to be grounded to enable
a dc-current flow. Applying a 20-mA full-scale output current would lead to a 0.5-VPP output for a 1:1 transformer
and a 1-VPP output for a 4:1 transformer. In general, the 1:1 transformer configuration has a better output
distortion, but the 4:1 transformer has 6 dB higher output power.
50 Ω
1:1
IOUT1
100 Ω
RLOAD
50 Ω
AGND
IOUT2
50 Ω
Figure 18. Driving a Doubly-Terminated 50-Ω Cable Using a 1:1 Impedance Ratio Transformer
100 Ω
4:1
IOUT1
AGND
RLOAD
50 Ω
IOUT2
100 Ω
Figure 19. Driving a Doubly-Terminated 50-Ω Cable Using a 4:1 Impedance Ratio Transformer
16
Submit Documentation Feedback
Copyright © 2007–2012, Texas Instruments Incorporated
Product Folder Links: DAC5652A
DAC5652A
www.ti.com
SLAS535D – SEPTEMBER 2007 – REVISED AUGUST 2012
Single-Ended Configuration
Figure 20 shows the single-ended output configuration, where the output current IOUT1 flows into an equivalent
load resistance of 25 Ω. Node IOUT2 must be connected to AGND or terminated with a resistor of 25 Ω to
AGND. The nominal resistor load of 25 Ω gives a differential output swing of 1 VPP when applying a 20-mA fullscale output current.
IOUT1
RLOAD
50 Ω
IOUT2
50 Ω
25 Ω
AGND
Figure 20. Driving a Doubly-Terminated 50-Ω Cable Using a Single-Ended Output
Reference Operation
Internal Reference
The DAC5652A has an on-chip reference circuit which comprises a 1.2-V bandgap reference and two control
amplifiers, one for each DAC. The full-scale output current, I(OUTFS), of the DAC5652A is determined by the
reference voltage, VREF, and the value of resistor RSET. I(OUTFS) is calculated by:
V
REF
I
+ 32 I
+ 32
OUTFS
REF
R
SET
(9)
The reference control amplifier operates as a V-to-I converter producing a reference current, IREF, which is
determined by the ratio of VREF and RSET (see Equation 9). The full-scale output current, I(OUTFS), results from
multiplying IREF by a fixed factor of 32.
Using the internal reference, a 2-kΩ resistor value results in a full-scale output of approximately 20 mA. Resistors
with a tolerance of 1% or better should be considered. Selecting higher values, the output current can be
adjusted from 20 mA down to 2 mA. Operating the DAC5652A at lower than 20-mA output currents may be
desirable for reasons of reducing the total power consumption, improving the distortion performance, or
observing the output compliance voltage limitations for a given load condition.
It is recommended to bypass the EXTIO pin with a ceramic chip capacitor of 0.1 µF or more. The control
amplifier is internally compensated and its small signal bandwidth is approximately 300 kHz.
External Reference
The internal reference can be disabled by simply applying an external reference voltage into the EXTIO pin,
which in this case functions as an input. The use of an external reference may be considered for applications that
require higher accuracy and drift performance or to add the ability of dynamic gain control.
While a 0.1-µF capacitor is recommended to be used with the internal reference, it is optional for the external
reference operation. The reference input, EXTIO, has a high input impedance (1 MΩ) and can be driven by
various sources. Note that the voltage range of the external reference must stay within the compliance range of
the reference input.
Submit Documentation Feedback
Copyright © 2007–2012, Texas Instruments Incorporated
Product Folder Links: DAC5652A
17
DAC5652A
SLAS535D – SEPTEMBER 2007 – REVISED AUGUST 2012
www.ti.com
Gain Setting Option
The full-scale output current on the DAC5652A can be set two ways: either for each of the two DAC channels
independently or for both channels simultaneously. For the independent gain set mode, the GSET pin (pin 42)
must be low (that is, connected to AGND). In this mode, two external resistors are required — one RSET
connected to the BIASJ_A pin (pin 44) and the other to the BIASJ_B pin (pin 41). In this configuration, the user
has the flexibility to set and adjust the full-scale output current for each DAC independently, allowing for the
compensation of possible gain mismatches elsewhere within the transmit signal path.
Alternatively, bringing the GSET pin high (that is, connected to AVDD), the DAC5652A switches into the
simultaneous gain set mode. Now the full-scale output current of both DAC channels is determined by only one
external RSET resistor connected to the BIASJ_A pin. The resistor at the BIASJ_B pin may be removed; however,
this is not required since this pin is not functional in this mode and the resistor has no effect on the gain equation.
Sleep Mode
The DAC5652A features a power-down function which can reduce the total supply current to approximately 3.1
mA over the specified supply range if no clock is present. Applying a logic high to the SLEEP pin initiates the
power-down mode, while a logic low enables normal operation. When left unconnected, an internal active
pulldown circuit enables the normal operation of the converter.
18
Submit Documentation Feedback
Copyright © 2007–2012, Texas Instruments Incorporated
Product Folder Links: DAC5652A
DAC5652A
www.ti.com
SLAS535D – SEPTEMBER 2007 – REVISED AUGUST 2012
REVISION HISTORY
Changes from Revision A (May 2009) to Revision B
•
Page
Changed the non-printing µ symbols in the Digital Input section of the Electrical Characteristics table (Units column)
to the correct µ symbols recognized by the PDF processor. ................................................................................................ 7
Changes from Revision B (December 2010) to Revision C
•
Page
Added the Thermal Information Table .................................................................................................................................. 2
Changes from Revision C (June 2011) to Revision D
Page
•
Deleted the VIH MAX value of 3.3 V. .................................................................................................................................... 7
•
Deleted the VIL MIN value of 0 V. ......................................................................................................................................... 7
Submit Documentation Feedback
Copyright © 2007–2012, Texas Instruments Incorporated
Product Folder Links: DAC5652A
19
PACKAGE OPTION ADDENDUM
www.ti.com
2-Aug-2012
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
DAC5652AIPFB
ACTIVE
TQFP
PFB
48
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
DAC5652AIPFBG4
ACTIVE
TQFP
PFB
48
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
DAC5652AIPFBR
ACTIVE
TQFP
PFB
48
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
DAC5652AIPFBRG4
ACTIVE
TQFP
PFB
48
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Samples
(Requires Login)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
2-Aug-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
DAC5652AIPFBR
Package Package Pins
Type Drawing
TQFP
PFB
48
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
1000
330.0
16.4
Pack Materials-Page 1
9.6
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
9.6
1.5
12.0
16.0
Q2
PACKAGE MATERIALS INFORMATION
www.ti.com
2-Aug-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
DAC5652AIPFBR
TQFP
PFB
48
1000
367.0
367.0
38.0
Pack Materials-Page 2
MECHANICAL DATA
MTQF019A – JANUARY 1995 – REVISED JANUARY 1998
PFB (S-PQFP-G48)
PLASTIC QUAD FLATPACK
0,27
0,17
0,50
36
0,08 M
25
37
24
48
13
0,13 NOM
1
12
5,50 TYP
7,20
SQ
6,80
9,20
SQ
8,80
Gage Plane
0,25
0,05 MIN
0°– 7°
1,05
0,95
Seating Plane
0,75
0,45
0,08
1,20 MAX
4073176 / B 10/96
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-026
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
Similar pages