AD ADAU1372BCPZ Low power codec Datasheet

Quad ADC, Dual DAC, Low Latency,
Low Power Codec
ADAU1372
Data Sheet
FEATURES
APPLICATIONS
Low latency, 24-bit ADCs and DACs
102 dB SNR (through PGA and ADC with A-weighted filter)
107 dB dynamic range (through DAC and headphone with
A-weighted filter)
Serial port sample rates from 8 kHz to 192 kHz
4 single-ended analog inputs, configurable as microphone or
line inputs
Dual stereo digital microphone inputs
Stereo analog audio output, single-ended or differential,
configurable as either line output or headphone driver
PLL supporting any input clock rate from 8 MHz to 27 MHz
Full-duplex, asynchronous sample rate converters (ASRCs)
Power supplies
Analog and digital input/output of 1.8 V to 3.3 V
Low power (15.5 mW)
I2C and SPI control interfaces for flexibility
5 multipurpose pins supporting dual stereo digital
microphone inputs, mute, push-button volume controls
Handsets, headsets, and headphones
Bluetooth® handsets, headsets, and headphones
Personal navigation devices
Digital still and video cameras
GENERAL DESCRIPTION
The ADAU1372 is a codec with four inputs and two outputs, which
incorporates asynchronous sample rate converters. Optimized
for low latency and low power, the ADAU1372 is ideal for headsets,
handsets, and headphones. The ADAU1372 has built-in programmable gain amplifiers (PGAs); thus, with the addition of just a
few passive components and a crystal, the ADAU1372 provides
a solution for headset audio needs, microphone preamplifiers,
ADCs, DACs, headphone amplifiers, and serial ports for
connections to an external DSP.
Note that throughout this data sheet, multifunction pins, such as
SCL/SCLK, are referred to either by the entire pin name or by a
single function of the pin, for example, SCLK, when only that
function is relevant.
MICBIAS1
MICROPHONE
BIAS GENERATORS
ADAU1372
POWER
MANAGEMENT
IOVDD
AVDD
AVDD
AVDD
DVDD
PD
MICBIAS0
REG_OUT
FUNCTIONAL BLOCK DIAGRAM
LDO
REGULATOR
ADC_SDATA1/CLKOUT/MP6
PLL
AIN0REF
PGA
CLOCK
OSCILLATOR
XTALI/MCLKIN
XTALO
Σ-Δ ADC
AIN0
DECIMATOR
AIN1REF
PGA
AIN1
Σ-Δ ADC
DECIMATOR
DMIC0_1/MP4
DMIC2_3/MP5
HPOUTLP/LOUTLP
Σ-Δ
DACs
HPOUTRP/LOUTRP
HPOUTLN/LOUTLN
INPUT/OUTPUT
SIGNAL ROUTING
DIGITAL
MICROPHONE
INPUTS
AIN2REF
Σ-Δ
DACs
HPOUTRN/LOUTRN
DECIMATOR
PGA
Σ-Δ ADC
AIN2
BIDIRECTIONAL
ASRCS
AIN3REF
DECIMATOR
PGA
AIN3
SERIAL I/O PORT
Σ-Δ ADC
I2C/SPI CONTROL
INTERFACE
12702-001
SDA/MISO
SCL/SCLK
ADDR0/SS
ADDR1/MOSI
DAC_SDATA/MP0
ADC_SDATA0/MP1
BCLK
LRCLK
AGND
AGND
AGND
DGND
DGND
CM
Figure 1.
Rev. 0
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
©2014 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
ADAU1372* PRODUCT PAGE QUICK LINKS
Last Content Update: 02/23/2017
COMPARABLE PARTS
DESIGN RESOURCES
View a parametric search of comparable parts.
• ADAU1372 Material Declaration
• PCN-PDN Information
EVALUATION KITS
• Quality And Reliability
• ADAU1372 Evaluation Board
• Symbols and Footprints
DOCUMENTATION
DISCUSSIONS
Data Sheet
View all ADAU1372 EngineerZone Discussions.
• ADAU1372: Quad ADC, Dual DAC, Low Latency, Low
Power Codec
SAMPLE AND BUY
User Guides
Visit the product page to see pricing options.
• UG-807: Evaluating the ADAU1372 Quad ADC, Dual DAC,
Low Latency, Low Power Codec
TOOLS AND SIMULATIONS
TECHNICAL SUPPORT
Submit a technical question or find your regional support
number.
• ADAU1372 IBIS Model
DOCUMENT FEEDBACK
Submit feedback for this data sheet.
This page is dynamically generated by Analog Devices, Inc., and inserted into this data sheet. A dynamic change to the content on this page will not
trigger a change to either the revision number or the content of the product data sheet. This dynamic page may be frequently modified.
ADAU1372
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Push-Button Volume Controls ................................................. 35
Applications ....................................................................................... 1
Mute ............................................................................................. 35
General Description ......................................................................... 1
Talkthrough Mode ..................................................................... 35
Functional Block Diagram .............................................................. 1
Serial Data Input/Output Ports .................................................... 36
Revision History ............................................................................... 3
Serial Port Initialization ............................................................ 36
Specifications..................................................................................... 4
Tristating Unused Channels...................................................... 37
Analog Performance Specifications ........................................... 4
Applications Information .............................................................. 39
Crystal Amplifier Specifications................................................. 7
Power Supply Bypass Capacitors .............................................. 39
Digital Input/Output Specifications........................................... 8
Layout .......................................................................................... 39
Power Supply Specifications........................................................ 8
Grounding ................................................................................... 39
Typical Power Consumption....................................................... 9
Exposed Pad PCB Design ......................................................... 39
Digital Filters ................................................................................. 9
System Block Diagram............................................................... 40
Digital Timing Specifications ................................................... 10
Register Summary: Low Latency Codec ..................................... 41
Absolute Maximum Ratings.......................................................... 13
Register Details: Low Latency Codec .......................................... 43
Thermal Resistance .................................................................... 13
Clock Control Register .............................................................. 43
ESD Caution ................................................................................ 13
PLL Denominator MSB Register .............................................. 44
Pin Configuration and Function Descriptions ........................... 14
PLL Denominator LSB Register ............................................... 44
Typical Performance Characteristics ........................................... 17
PLL Numerator MSB Register .................................................. 44
Theory of Operation ...................................................................... 24
PLL Numerator LSB Register.................................................... 44
System Clocking and Power-Up ................................................... 25
PLL Integer Setting Register ..................................................... 45
Initialization ................................................................................ 25
PLL Lock Flag Register .............................................................. 46
Clock Initialization ..................................................................... 25
CLKOUT Setting Selection Register ........................................ 46
PLL ............................................................................................... 25
Regulator Control Register ....................................................... 47
Clock Output............................................................................... 26
DAC Input Select Register ........................................................ 47
Power Sequencing ...................................................................... 26
Serial Data Output 0/Serial Data Output 1 Input Select
Register ........................................................................................ 48
Signal Routing ................................................................................. 27
Input Signal Paths ........................................................................... 28
Analog Inputs .............................................................................. 28
Digital Microphone Input ......................................................... 29
Analog-to-Digital Converters ................................................... 29
Serial Data Output 2/Serial Data Output 3 Input Select
Register ........................................................................................ 49
Serial Data Output 4/Serial Data Output 5 Input Select
Register ........................................................................................ 50
Output Signal Paths ........................................................................ 30
Serial Data Output 6/Serial Data Output 7 Input Select
Register ........................................................................................ 51
Analog Outputs........................................................................... 30
ADC_SDATA0/ADC_SDATA1 Channel Select Register ..... 53
Digital-to-Analog Converters ................................................... 30
Output ASRC0/Output ASRC1 Source Register .................... 53
Asynchronous Sample Rate Converters .................................. 30
Output ASRC2/Output ASRC3 Source Register .................... 54
Control Port..................................................................................... 31
Input ASRC Channel Select Register ....................................... 56
Burst Mode Communication .................................................... 31
ADC Control 0 Register ............................................................ 56
2
I C Port ........................................................................................ 31
ADC Control 1 Register ............................................................ 57
SPI Port ........................................................................................ 34
ADC Control 2 Register ............................................................ 58
Burst Mode Communication .................................................... 34
ADC Control 3 Register ............................................................ 59
Multipurpose Pins .......................................................................... 35
ADC0 Volume Control Register .............................................. 60
Rev. 0 | Page 2 of 92
Data Sheet
ADAU1372
ADC1 Volume Control Register ...............................................60
MP1 Function Setting Register ................................................. 75
ADC2 Volume Control Register ...............................................61
MP4 Function Setting Register ................................................. 76
ADC3 Volume Control Register ...............................................61
MP5 Function Setting Register ................................................. 77
PGA Control 0 Register..............................................................62
MP6 Function Setting Register ................................................. 78
PGA Control 1 Register..............................................................62
Push-Button Volume Settings Register .................................... 79
PGA Control 2 Register..............................................................63
Push-Button Volume Control Assignment Register .............. 80
PGA Control 3 Register..............................................................64
Debounce Modes Register ......................................................... 81
PGA Slew Control Register........................................................64
Headphone Line Output Select Register .................................. 81
PGA 10 dB Gain Boost Register................................................65
Decimator Power Control Register .......................................... 82
Input and Output Capacitor Charging Register .....................66
ADC to DAC Talkthrough Bypass Path Register....................67
ASRC Interpolator and DAC Modulator Power Control
Register ......................................................................................... 83
Talkthrough Bypass Gain for ADC0 Register .........................67
Analog Bias Control 0 Register ................................................. 84
Talkthrough Bypass Gain for ADC1 Register .........................67
Analog Bias Control 1 Register ................................................. 85
MICBIAS Control Register ........................................................68
Digital Pin Pull-Up Control 0 Register .................................... 86
DAC Control 1 Register .............................................................69
Digital Pin Pull-Up Control 1 Register .................................... 87
DAC0 Volume Control Register................................................69
Digital Pin Pull-Down Control 2 Register .............................. 88
DAC1 Volume Control Register................................................70
Digital Pin Pull-Down Control 3 Register .............................. 89
Headphone Output Mutes Register ..........................................70
Digital Pin Drive Strength Control 4 Register ........................ 90
Serial Port Control 0 Register ....................................................71
Digital Pin Drive Strength Control 5 Register ........................ 91
Serial Port Control 1 Register ....................................................72
Outline Dimensions ........................................................................ 92
TDM Output Channel Disable Register ..................................73
Ordering Guide ........................................................................... 92
MP0 Function Setting Register .................................................74
REVISION HISTORY
12/14—Revision 0: Initial Version
Rev. 0 | Page 3 of 92
ADAU1372
Data Sheet
SPECIFICATIONS
Master clock = 12.288 MHz, serial input sample rate = 48 kHz, measurement bandwidth = 20 Hz to 20 kHz, word width = 24 bits,
ambient temperature = 25°C, outputs line loaded with 10 kΩ.
ANALOG PERFORMANCE SPECIFICATIONS
Supply voltages AVDD = IOVDD = 1.8 V, DVDD = 1.1 V, unless otherwise noted, PLL disabled, direct master clock.
Table 1.
Parameter
ANALOG-TO-DIGITAL CONVERTERS (ADCs)
ADC Resolution
Digital Attenuation Step
Digital Attenuation Range
INPUT RESISTANCE
Single-Ended Line Input
PGA Inputs
SINGLE-ENDED LINE INPUT
Full-Scale Input Voltage
Dynamic Range 1
With A-Weighted Filter (RMS)
With Flat 20 Hz to 20 kHz Filter
Signal-to-Noise Ratio (SNR) 2
With A-Weighted Filter (RMS)
With Flat 20 Hz to 20 kHz Filter
Interchannel Gain Mismatch
Total Harmonic Distortion + Noise (THD + N)
Offset Error
Gain Error
Interchannel Isolation
Power Supply Rejection Ratio (PSRR)
SINGLE-ENDED PGA INPUT
Full-Scale Input Voltage
Dynamic Range1
With A-Weighted Filter (RMS)
With Flat 20 Hz to 20 kHz Filter
Test Conditions/Comments
All ADCs
Gain settings do not include 10 dB gain from
PGA_x_BOOST settings; this additional gain does not
affect input impedance; PGA_POP_DISx = 1
0 dB gain
−12 dB gain
0 dB gain
+35.25 dB gain
PGA_ENx = 0, PGA_x_BOOST = 0, PGA_POP_DISx = 1
Scales linearly with AVDD
AVDD = 1.8 V
AVDD = 1.8 V
AVDD = 3.3 V
AVDD = 3.3 V
20 Hz to 20 kHz, −60 dB input
AVDD = 1.8 V
AVDD = 3.3 V
AVDD = 1.8 V
AVDD = 3.3 V
AVDD = 1.8 V
AVDD = 3.3 V
AVDD = 1.8 V
AVDD = 3.3 V
20 Hz to 20 kHz, −1 dBFS input
AVDD = 1.8 V
AVDD = 3.3 V
CM capacitor = 22 µF
CM capacitor = 22 µF, 100 mV p-p at 1 kHz
PGA_ENx = 1, PGA_x_BOOST = 0
Scales linearly with AVDD
AVDD = 1.8 V
AVDD = 1.8 V
AVDD = 3.3 V
AVDD = 3.3 V
20 Hz to 20 kHz, −60 dB input
AVDD = 1.8 V
AVDD = 3.3 V
AVDD = 1.8 V
AVDD = 3.3 V
Rev. 0 | Page 4 of 92
Min
Typ
Max
Unit
24
0.375
95
Bits
dB
dB
14.3
32.0
20
0.68
kΩ
kΩ
kΩ
kΩ
AVDD/3.63
0.49
1.38
0.90
2.54
V rms
V rms
V p-p
V rms
V p-p
97
102
94
99
dB
dB
dB
dB
98
103
96
100
40
dB
dB
dB
dB
mdB
−90
−94
±0.1
±0.2
100
55
dB
dB
mV
dB
dB
dB
AVDD/3.63
0.49
1.38
0.90
2.54
V rms
V rms
V p-p
V rms
V p-p
96
102
94
99
dB
dB
dB
dB
Data Sheet
Parameter
THD + N
SNR2
With A-Weighted Filter (RMS)
With Flat 20 Hz to 20 kHz Filter
PGA Gain Variation
With −12 dB Setting
With +35.25 dB Setting
PGA Boost
PGA Mute Attenuation
Interchannel Gain Mismatch
Offset Error
Gain Error
Interchannel Isolation
PSRR
MICROPHONE BIAS
Bias Voltage
0.65 × AVDD
0.90 × AVDD
Bias Current Source
Output Impedance
MICBIASx Isolation
Noise in the Signal Bandwidth 3
AVDD = 1.8 V
ADAU1372
Test Conditions/Comments
20 Hz to 20 kHz, −1 dBFS input
AVDD = 1.8 V
AVDD = 3.3 V
Min
Typ
Max
Unit
−88
−90
dB
dB
AVDD = 1.8 V
AVDD = 3.3 V
AVDD = 1.8 V
AVDD = 3.3 V
96
102
94
99
dB
dB
dB
dB
Standard deviation
Standard deviation
PGA_x_BOOST
PGA_MUTEx
0.05
0.15
10
−65
0.005
0
±0.2
83
63
dB
dB
dB
dB
dB
mV
dB
dB
dB
1.16
2.12
1.63
2.97
1
95
99
V
V
V
V
mA
Ω
dB
dB
MIC_GAINx = 0
MIC_GAINx = 1
27
16
nV/√Hz
nV/√Hz
MIC_GAINx = 0
MIC_GAINx = 1
35
19
nV/√Hz
nV/√Hz
All DACs
24
0.375
95
Bits
dB
dB
AVDD/3.4
0.53
1.50
0.97
2.74
−72
V rms
V rms
V p-p
V rms
V p-p
dB
100
104
97
101
dB
dB
dB
dB
100
104
dB
dB
CM capacitor = 22 µF, 100 mV p-p at 1 kHz
MIC_ENx = 1
AVDD = 1.8 V, MIC_GAINx = 1
AVDD = 3.3 V, MIC_GAINx = 1
AVDD = 1.8 V, MIC_GAINx = 0
AVDD = 3.3 V, MIC_GAINx = 0
3
MIC_GAINx = 0
MIC_GAINx = 1
20 Hz to 20 kHz
AVDD = 3.3 V
DIGITAL-TO-ANALOG CONVERTERS (DACs)
DAC Resolution
Digital Attenuation Step
Digital Attenuation Range
DAC SINGLE-ENDED OUTPUT
Full-Scale Output Voltage
Mute Attenuation
Line Output Mode
Dynamic Range1
With A-Weighted Filter (RMS)
With Flat 20 Hz to 20 kHz Filter
SNR2
With A-Weighted Filter (RMS)
Single-ended operation, HPOUTLP/LOUTLP and
HPOUTRP/LOUTRP pins
Scales linearly with AVDD
AVDD = 1.8 V
AVDD = 1.8 V, 0 dBFS
AVDD = 3.3 V
AVDD = 3.3 V, 0 dBFS
20 Hz to 20 kHz, −60 dB input
AVDD = 1.8 V
AVDD = 3.3 V
AVDD = 1.8 V
AVDD = 3.3 V
20 Hz to 20 kHz
AVDD = 1.8 V
AVDD = 3.3 V
Rev. 0 | Page 5 of 92
ADAU1372
Parameter
With Flat 20 Hz to 20 kHz Filter
Interchannel Gain Mismatch
THD + N
Gain Error
Headphone Mode
Dynamic Range1
With A-Weighted Filter (RMS)
With Flat 20 Hz to 20 kHz Filter
SNR2
With A-Weighted Filter (RMS)
With Flat 20 Hz to 20 kHz Filter
Interchannel Gain Mismatch
THD + N
32 Ω Load
24 Ω Load
16 Ω Load
Gain Error
Headphone Output Power
32 Ω Load
24 Ω Load
16 Ω Load
Offset Error
Interchannel Isolation
PSRR
DAC DIFFERENTIAL OUTPUT
Full-Scale Output Voltage
Mute Attenuation
Line Output Mode
Dynamic Range1
With A-Weighted Filter (RMS)
With Flat 20 Hz to 20 kHz Filter
SNR2
With A-Weighted Filter (RMS)
With Flat 20 Hz to 20 kHz Filter
Data Sheet
Test Conditions/Comments
AVDD = 1.8 V
AVDD = 3.3 V
20 Hz to 20 kHz, −1 dBFS input
AVDD = 1.8 V
AVDD = 3.3 V
20 Hz to 20 kHz, −60 dB input
AVDD = 1.8 V
AVDD = 3.3 V
AVDD = 1.8 V
AVDD = 3.3 V
20 Hz to 20 kHz
AVDD = 1.8 V
AVDD = 3.3 V
AVDD = 1.8 V
AVDD = 3.3 V
20 Hz to 20 kHz, −1 dBFS input
AVDD = 1.8 V, output power = 6.7 mW
AVDD = 3.3 V, output power = 22.4 mW
AVDD = 1.8 V, output power = 8.9 mW
AVDD = 3.3 V, output power = 30 mW
AVDD = 1.8 V, output power = 13 mW
AVDD = 3.3 V, output power = 44 mW
AVDD = 1.8 V, <0.1% THD + N
AVDD = 3.3 V, <0.1% THD + N
AVDD = 1.8 V, <0.1% THD + N
AVDD = 3.3 V, <0.1% THD + N
AVDD = 1.8 V, <0.1% THD + N
AVDD = 3.3 V, <0.1% THD + N
1 kHz, 0 dBFS input signal
CM capacitor = 22 µF, 100 mV p-p at 1 kHz
Differential operation
Scales linearly with AVDD
AVDD = 1.8 V
AVDD = 1.8 V, 0 dBFS input
AVDD = 3.3 V
AVDD = 3.3 V, 0 dBFS input
20 Hz to 20 kHz, −60 dB input
AVDD = 1.8 V
AVDD = 3.3 V
AVDD = 1.8 V
AVDD = 3.3 V
20 Hz to 20 kHz
AVDD = 1.8 V
AVDD = 3.3 V
AVDD = 1.8 V
AVDD = 3.3 V
Interchannel Gain Mismatch
Rev. 0 | Page 6 of 92
Min
Typ
98
102
20
Max
−93
−94
±0.1
Unit
dB
dB
mdB
dB
dB
dB
dB
100
104
97
101
dB
dB
dB
dB
100
104
98
102
50
dB
dB
dB
dB
mdB
−77
−80
−76
−79
−74
−77
±0.1
dB
dB
dB
dB
dB
dB
dB
8.4
28.1
11.2
37.4
16.25
55.8
±0.1
100
70
mW
mW
mW
mW
mW
mW
mV
dB
dB
AVDD/1.7
1.06
3.00
1.94
5.49
−72
V rms
V rms
V p-p
V rms
V p-p
dB
104
107
101
105
dB
dB
dB
dB
105
108
102
105
20
dB
dB
dB
dB
mdB
Data Sheet
Parameter
THD + N
Gain Error
Headphone Mode
Dynamic Range1
With A-Weighted Filter (RMS)
With Flat 20 Hz to 20 kHz Filter
SNR2
With A-Weighted Filter (RMS)
With Flat 20 Hz to 20 kHz Filter
Interchannel Gain Mismatch
THD + N
32 Ω Load
24 Ω Load
16 Ω Load
Gain Error
Headphone Output Power
32 Ω Load
24 Ω Load
16 Ω Load
Offset Error
Interchannel Isolation
PSRR
CM REFERENCE
Common-Mode Reference Output
Common-Mode Source Impedance
REGULATOR
Line Regulation
Load Regulation
1
2
3
ADAU1372
Test Conditions/Comments
20 Hz to 20 kHz, −1 dBFS input
AVDD = 1.8 V
AVDD = 3.3 V
Line output mode
Min
−96
−96
±0.25
Unit
dB
dB
dB
dB
104
107
102
104
dB
dB
dB
dB
105
108
103
106
75
dB
dB
dB
dB
mdB
−1 dBFS, AVDD = 1.8 V, output power = 27 mW
−1 dBFS, AVDD = 3.3 V, output power = 90 mW
−2 dBFS, AVDD = 1.8 V, output power = 28 mW
−1 dBFS, AVDD = 3.3 V, output power = 118 mW
−3 dBFS, AVDD = 1.8 V, output power = 33 mW
−1 dBFS, AVDD = 3.3 V, output power = 175 mW
−75
−83
−75
−77
−75
−83
±0.25
dB
dB
dB
dB
dB
dB
dB
AVDD = 1.8 V, <0.1% THD + N
AVDD = 3.3 V, <0.1% THD + N
AVDD = 1.8 V, <0.1% THD + N
AVDD = 3.3 V, <0.1% THD + N
AVDD = 1.8 V, <0.1% THD + N
AVDD = 3.3 V, <0.1% THD + N
32.5
111.8
37.6
148.3
41.5
189.2
±0.1
100
73
mW
mW
mW
mW
mW
mW
mV
dB
dB
AVDD/2
5
V
kΩ
1
6
mV/V
mV/mA
20 Hz to 20 kHz, −60 dB input
AVDD = 1.8 V
AVDD = 3.3 V
AVDD = 1.8 V
AVDD = 3.3 V
20 Hz to 20 kHz
AVDD = 1.8 V
AVDD = 3.3 V
AVDD = 1.8 V
AVDD = 3.3 V
1 kHz, 0 dBFS input signal
CM capacitor = 22 µF, 100 mV p-p at 1 kHz
CM pin
Typ
Max
Dynamic range is the ratio of the sum of the noise and harmonic power in the band of interest with a −60 dBFS signal present to the full-scale power level in decibels.
SNR is the ratio of the sum of all noise power in the band of interest with no signal present to the full-scale power level in decibels.
These specifications are tested with a 4.7 µF decoupling capacitor and 5.0 kΩ load on the MICBIASx pins.
CRYSTAL AMPLIFIER SPECIFICATIONS
Supply voltages AVDD = IOVDD = 1.8 V, DVDD = 1.1 V, unless otherwise noted.
Table 2.
Parameter
Jitter
Frequency Range
Load Capacitance
Min
8
Rev. 0 | Page 7 of 92
Typ
270
Max
500
27
20
Unit
ps
MHz
pF
ADAU1372
Data Sheet
DIGITAL INPUT/OUTPUT SPECIFICATIONS
−40°C < TA < +85°C, IOVDD = 3.3 V ± 10% and 1.8 V − 5%/+10%.
Table 3.
Parameter
INPUT/OUTPUT
Input Voltage
High (VIH)
Low (VIL)
Input Leakage
Output Voltage
High (VOH)
Low Drive Strength
High Drive Strength
Low (VOL)
Low Drive Strength
High Drive Strength
Input Capacitance
Test Conditions/Comments
Min
Typ
IOVDD = 3.3 V
IOVDD = 1.8 V
IOVDD = 3.3 V
IOVDD = 1.8 V
IOVDD = 3.3 V, IIH at VIH = 2.0 V
IIL at VIL = 0.8 V
IOVDD = 1.8 V, IIH at VIH = 1.1 V
IIL at VIL = 0.45 V
2.0
1.1
IOH = 1 mA
IOH = 3 mA
IOVDD − 0.6
IOVDD − 0.6
Max
Unit
0.8
0.45
10
10
10
10
V
V
V
V
µA
µA
µA
µA
V
V
IOL = 1 mA
IOL = 3 mA
0.4
0.4
5
V
V
pF
POWER SUPPLY SPECIFICATIONS
Supply voltages AVDD = IOVDD = 1.8 V, DVDD = 1.1 V, unless otherwise noted, PLL disabled, direct master clock.
Table 4.
Parameter
SUPPLIES
AVDD Voltage
DVDD Voltage
IOVDD Voltage
Digital Input/Output Current with IOVDD = 1.8 V
Slave Mode
Master Mode
Power-Down
Digital Input/Output Current with IOVDD = 3.3 V
Slave Mode
Master Mode
Power-Down
Analog Current (AVDD)
Power-Down
Test Conditions/Comments
Crystal oscillator enabled
fS = 8 kHz
fS = 48 kHz
fS = 192 kHz
fS = 8 kHz
fS = 48 kHz
fS = 192 kHz
Crystal oscillator enabled
fS = 8 kHz
fS = 48 kHz
fS = 192 kHz
fS = 8 kHz
fS = 48 kHz
fS = 192 kHz
See Table 5
AVDD = 1.8 V
AVDD = 3.3 V
Rev. 0 | Page 8 of 92
Min
Typ
Max
Unit
1.71
1.045
1.71
1.8
1.1
1.8
3.63
1.98
3.63
V
V
V
0.32
0.35
0.49
0.35
0.53
1.18
0
mA
mA
mA
mA
mA
mA
µA
1.99
2.05
2.28
2.05
2.4
3.62
7
mA
mA
mA
mA
mA
mA
µA
0.6
13.6
µA
µA
Data Sheet
ADAU1372
Parameter
DISSIPATION
Operation
All Supplies
Digital Input/Output Supply
Analog Supply
Power-Down, All Supplies
Test Conditions/Comments
Min
Typ
Max
Unit
fS = 192 kHz (see conditions in Table 5)
15.5
0.7
14.8
1
Includes regulated DVDD current
mW
mW
mW
µW
TYPICAL POWER CONSUMPTION
Unless otherwise noted, IOVDD = 1.8 V, AVDD = 1.8 V, master clock = 12.288 MHz, fS = 192 kHz; on-board regulator enabled and set to
1.2 V, PLL enabled, two ADCs with PGA enabled and two ADCs configured for line input, no input signal. ADC0 and ADC1 are routed
to ADC_SDATA0 and ADC_SDATA0 is externally routed back into the DAC_SDATA input. The serial port is set to slave. Two DACs are
configured for differential line output operation; DAC outputs are unloaded. Both MICBIAS0 and MICBIAS1 are enabled. For total
power consumption, add IOVDD at the 8 kHz slave current listed in Table 4.
Table 5.
Operating Voltage
AVDD = IOVDD = 3.3 V
AVDD = IOVDD = 1.8 V
Power Management Setting
Normal (default)
Extreme power saving
Power saving
Enhanced performance
Normal (default)
Extreme power saving
Power saving
Enhanced performance
Typical AVDD Power Consumption (mA)
11.5
9.4
9.8
12.65
9.37
7.40
7.78
10.4
Typical ADC
THD + N (dB)
−93
−93
−93
−93
−86
−84.5
−84.5
−86
Typical HP Output
THD + N (dB)
−87.5
−86.5
−86.5
−90.5
−91
−87
−87.5
−94.5
DIGITAL FILTERS
Table 6.
Parameter
SAMPLE RATE CONVERTER
Pass Band
Pass-Band Ripple
Test Conditions/Comments
Min
LRCLK < 63 kHz
63 kHz < LRCLK <130 kHz
LRCLK > 130 kHz
Upsampling, 96 kHz
Upsampling, 192 kHz
Downsampling, 96 kHz
Downsampling, 192 kHz
0
0
0
−0.27
−0.06
0
0
8
Input/Output Frequency Range
Dynamic Range
THD + N
Startup Time
Typ
Max
Unit
0.475 × fS
0.4286 × fS
0.4286 × fS
+0.05
+0.05
0.07
0.07
192
kHz
kHz
kHz
dB
dB
dB
dB
kHz
dB
dB
ms
100
−90
15
Rev. 0 | Page 9 of 92
ADAU1372
Data Sheet
DIGITAL TIMING SPECIFICATIONS
−40°C < TA < +85°C, IOVDD = 1.71 V to 3.63 V, DVDD = 1.045 V to 1.98 V.
Table 7. Digital Timing
Parameter
MASTER CLOCK
tMP
tMCLK
SERIAL PORT
tBL
tBH
tLS
tLH
tSS
tSH
tTS
tSOD
tSOTD
tSOTX
SPI PORT
fSCLK
tCCPL
tCCPH
tCLS
tCLH
tCLPH
tCDS
tCDH
tCOD
I2C PORT
fSCL
tSCLH
tSCLL
tSCS
tSCR
tSCH
tDS
tSCF
tSDF
tBFT
MULTIPURPOSE AND POWERDOWN PINS
tGIL
tRLPW
DIGITAL MICROPHONE
tCF
tCR
tDS
tDE
tMIN
tMAX
Unit
Description
37
77
125
82
ns
ns
MCLKIN period; 8 MHz to 27 MHz input clock using PLL
Internal MCLK period; direct MCLK and PLL output divided by 2
10
34
30
ns
ns
ns
ns
ns
ns
ns
ns
ns
30
ns
BCLK low pulse width (master and slave modes)
BCLK high pulse width (master and slave modes)
LRCLK setup; time to BCLK rising (slave mode)
LRCLK hold; time from BCLK rising (slave mode)
DAC_SDATA setup; time to BCLK rising (master and slave modes)
DAC_SDATA hold; time from BCLK rising (master and slave modes)
BCLK falling to LRCLK timing skew (master mode)
ADC_SDATAx delay; time from BCLK falling (master and slave modes)
BCLK falling to ADC_SDATAx driven in time-division multiplexing (TDM)
tristate mode
BCLK falling to ADC_SDATAx tristate in TDM tristate mode
6.25
MHz
ns
ns
ns
ns
ns
ns
ns
ns
SCLK frequency
SCLK pulse width low
SCLK pulse width high
SS setup; time to SCLK rising
SS hold; time from SCLK rising
SS pulse width high
MOSI setup; time to SCLK rising
MOSI hold; time from SCLK rising
MISO delay; time from SCLK falling
kHz
µs
µs
µs
ns
µs
ns
ns
ns
µs
SCL frequency
SCL high
SCL low
SCL rise setup time (to SDA falling), relevant for repeated start condition
SCL and SDA rise time, CLOAD = 400 pF
SCL fall hold time (from SDA falling), relevant for start condition
SDA setup time (to SCL rising)
SCL fall time; CLOAD = 400 pF
SDA fall time; CLOAD = 400 pF; not shown in Figure 5
SCL rise setup time (to SDA rising), relevant for stop condition
1.5 × 1/fS
µs
ns
MPx input latency; time until high or low value is read
PD low pulse width
20
20
ns
ns
0
ns
Digital microphone clock fall time
Digital microphone clock rise time
Digital microphone valid data start time
Digital microphone valid data end time
40
40
10
10
5
5
0
80
80
5
100
80
10
10
101
400
0.6
1.3
0.6
250
0.6
100
250
250
0.6
20
40
Rev. 0 | Page 10 of 92
Data Sheet
ADAU1372
Digital Timing Diagrams
tBH
BCLK
tBL
tLH
tLS
LRCLK
tSS
DAC_SDATA
LEFT JUSTIFIED
MODE
MSB
MSB – 1
tSH
tSS
DAC_SDATA
I2S MODE
MSB
tSH
tSS
tSS
DAC_SDATA
RIGHT JUSTIFIED
MODE
LSB
MSB
tSH
tSH
8-BIT CLOCKS
(24-BIT DATA)
12-BIT CLOCKS
(20-BIT DATA)
12702-002
14-BIT CLOCKS
(18-BIT DATA)
16-BIT CLOCKS
(16-BIT DATA)
Figure 2. Serial Input Port Timing
tLH
tBH
tTS
BCLK
tBL
tLS
LRCLK
ADC_SDATAx
LEFT JUSTIFIED
MODE
tSOD
MSB
MSB – 1
tSOD
ADC_SDATAx
I2S MODE
tSOTX
tSOTD
HIGH-Z
HIGH-Z
LSB
MSB
tSOD
ADC_SDATAx
RIGHT JUSTIFIED
MODE
MSB
LSB
8-BIT CLOCKS
(24-BIT DATA)
12-BIT CLOCKS
(20-BIT DATA)
14-BIT CLOCKS
(18-BIT DATA)
12702-003
ADC_SDATAx
WITH TRISTATE
MSB
16-BIT CLOCKS
(16-BIT DATA)
Figure 3. Serial Output Port Timing
Rev. 0 | Page 11 of 92
ADAU1372
Data Sheet
tCLH
tCLS
tCLPH
tCCPL
tCCPH
SS
SCLK
MOSI
tCDH
12702-004
tCDS
MISO
tCOD
Figure 4. SPI Port Timing
tDS
tSCH
tSCH
SDA
SCL
tSCLL
tBFT
tSCS
tSCF
12702-005
tSCLH
tSCR
Figure 5. I2C Port Timing
CLKOUT
tDS
tCF
tDS
tDE
tDE
DMIC0_1/DMIC2_3
VALID LEFT SAMPLE
VALID RIGHT SAMPLE
Figure 6. Digital Microphone Timing
Rev. 0 | Page 12 of 92
VALID LEFT SAMPLE
12702-006
tCR
Data Sheet
ADAU1372
ABSOLUTE MAXIMUM RATINGS
THERMAL RESISTANCE
Table 8.
Parameter
Power Supplies (AVDD, IOVDD)
Digital Supply (DVDD)
Input Current (Except Supply Pins)
Analog Input Voltage (Signal Pins)
Digital Input Voltage (Signal Pins)
Operating Temperature Range (Case)
Storage Temperature Range
Rating
−0.3 V to +3.63 V
−0.3 V to +1.98 V
±20 mA
−0.3 V to AVDD + 0.3 V
−0.3 to IOVDD + 0.3 V
−40°C to +85°C
−65°C to +150°C
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
θJA represents the junction-to-ambient thermal resistance; θJC
represents the junction-to-case thermal resistance. Thermal
numbers are simulated on a 4-layer JEDEC printed circuit
board (PCB) with the exposed pad soldered to the PCB. θJC is
simulated at the exposed pad on the bottom of the package.
Table 9. Thermal Resistance
Package Type
40-Lead LFCSP
ESD CAUTION
Rev. 0 | Page 13 of 92
θJA
29
θJC
1.8
Unit
°C/W
ADAU1372
Data Sheet
40
39
38
37
36
35
34
33
32
31
IOVDD
XTALI/MCLKIN
XTALO
DMIC0_1/MP4
DMIC2_3/MP5
ADC_SDATA1/CLKOUT/MP6
ADC_SDATA0/MP1
DAC_SDATA/MP0
BCLK
LRCLK
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
ADAU1372
TOP VIEW
(Not to Scale)
30
29
28
27
26
25
24
23
22
21
DGND
DVDD
REG_OUT
PD
HPOUTRP/LOUTRP
HPOUTRN/LOUTRN
AVDD
AGND
HPOUTLP/LOUTLP
HPOUTLN/LOUTLN
NOTES
1. THE EXPOSED PAD IS CONNECTED INTERNALLY TO THE ADAU1372
GROUNDS. FOR INCREASED RELIABILITY OF THE SOLDER JOINTS AND
MAXIMUM THERMAL CAPABILITY, IT IS RECOMMENDED THAT THE PAD
BE SOLDERED TO THE GROUND PLANE. SEE THE EXPOSED PAD PCB
DESIGN SECTION FOR MORE INFORMATION.
12702-007
AGND
CM
AIN1REF
AIN1
AIN2REF
AIN2
AIN3REF
AIN3
AVDD
AGND
11
12
13
14
15
16
17
18
19
20
SDA/MISO 1
SCL/SCLK 2
ADDR1/MOSI 3
ADDR0/SS 4
DGND 5
MICBIAS0 6
MICBIAS1 7
AIN0REF 8
AIN0 9
AVDD 10
Figure 7. Pin Configuration
Table 10. Pin Function Descriptions
Pin
No.
1
Mnemonic
SDA/MISO
Type 1
D_IO
2
SCL/SCLK
D_IN
3
ADDR1/MOSI
D_IN
4
ADDR0/SS
D_IN
5
6
7
8
9
10
11
DGND
MICBIAS0
MICBIAS1
AIN0REF
AIN0
AVDD
AGND
PWR
A_OUT
A_OUT
A_IN
A_IN
PWR
PWR
Description
I2C Data (SDA). This pin is a bidirectional open-collector. The line connected to this pin must
have a 2.0 kΩ pull-up resistor.
SPI Data Output (MISO). This SPI data output reads back registers. It is tristated when an SPI
read is not active.
I2C Clock (SCL). This pin is always an open-collector input when the device is in I2C control
mode. The line connected to this pin must have a 2.0 kΩ pull-up resistor in I2C mode.
SPI Clock (SCLK). This pin can either run continuously or be gated off between SPI
transactions.
I2C Address 1 (ADDR1).
SPI Data Input (MOSI).
I2C Address 0 (ADDR0).
SPI Latch Signal (SS). This pin must go low at the beginning of an SPI transaction and high at
the end of a transaction. Each SPI transaction can take a different number of SCLK cycles to
complete, depending on the address and the read/write bit sent at the beginning of the SPI
transaction.
Digital Ground. Tie the AGND and DGND pins directly together in a common ground plane.
Bias Voltage for Electret Microphone. Decouple with a 1 µF capacitor.
Bias Voltage for Electret Microphone. Decouple with a 1 µF capacitor.
ADC0 Input Reference. AC couple this reference pin to ground with a 10 µF capacitor.
ADC0 Input.
1.8 V to 3.3 V Analog Supply. Decouple this pin to AGND with a 0.1 µF capacitor.
Analog Ground. Tie the AGND and DGND pins directly together in a common ground plane.
Decouple AGND to AVDD with a 0.1 µF capacitor.
Rev. 0 | Page 14 of 92
Data Sheet
ADAU1372
Pin
No.
12
Mnemonic
CM
Type 1
A_OUT
13
14
15
16
17
18
19
20
21
AIN1REF
AIN1
AIN2REF
AIN2
AIN3REF
AIN3
AVDD
AGND
HPOUTLN/LOUTLN
A_IN
A_IN
A_IN
A_IN
A_IN
A_IN
PWR
PWR
A_OUT
22
HPOUTLP/LOUTLP
A_OUT
23
24
AGND
AVDD
PWR
PWR
25
HPOUTRN/LOUTRN
A_OUT
26
HPOUTRP/LOUTRP
A_OUT
27
PD
D_IN
28
REG_OUT
A_OUT
29
DVDD
PWR
30
31
32
33
DGND
LRCLK
BCLK
DAC_SDATA/MP0
PWR
D_IO
D_IO
D_IO
34
ADC_SDATA0/MP1
D_IO
35
ADC_SDATA1/CLKOUT/MP6
D_IO
36
DMIC2_3/MP5
D_IN
37
DMIC0_1/MP4
D_IN
38
XTALO
A_OUT
39
XTALI/MCLKIN
D_IN
Description
AVDD/2 V Common-Mode Reference. Connect a 10 µF to 47 µF decoupling capacitor
between this pin and ground to reduce crosstalk between the ADCs and DACs. The material
of the capacitors is not critical. This pin can be used to bias external analog circuits, as long
as they are not drawing current from CM (for example, the noninverting input of an
operational amplifier).
ADC1 Input Reference. AC couple this reference pin to ground with a 10 µF capacitor.
ADC1 Input.
ADC2 Input Reference. AC couple this reference pin to ground with a 10 µF capacitor.
ADC2 Input.
ADC3 Input Reference. AC couple this reference pin to ground with a 10 µF capacitor.
ADC3 Input.
1.8 V to 3.3 V Analog Supply. Decouple this pin to AGND with a 0.1 µF capacitor.
Analog Ground. See the Grounding section.
Left Headphone Inverted (HPOUTLN).
Line Output Inverted (LOUTLN).
Left Headphone Noninverted (HPOUTLP).
Line Output Noninverted, Single-Ended Line Output (LOUTLP).
Headphone Amplifier Ground. See the Grounding section.
Headphone Amplifier Power, 1.8 V to 3.3 V Analog Supply. Decouple this pin to AGND with a
0.1 µF capacitor. The PCB trace to this pin must be able to supply the higher current necessary for
driving the headphone outputs.
Right Headphone Inverted (HPOUTRN).
Line Output Inverted (LOUTRN).
Right Headphone Noninverted (HPOUTRP).
Line Output Noninverted, Single-Ended Line Output (LOUTRP).
Active Low Power-Down. All digital and analog circuits are powered down. There is an
internal pull-down resistor on this pin; therefore, the ADAU1372 is held in power-down
mode if its input signal is floating while power is applied to the supply pins.
Regulator Output Voltage. Connect this pin to DVDD if the internal voltage regulator is
generating the DVDD voltage.
Digital Core Supply. The digital supply can be generated from an on-board regulator or
supplied directly from an external supply. In each case, decouple DVDD to DGND with a
0.1 µF capacitor.
Digital Ground. See the Grounding section.
Serial Data Port Frame Clock.
Serial Data Port Bit Clock.
DAC Serial Input Data (DAC_SDATA).
General-Purpose Input (MP0).
ADC Serial Data Output 0 (ADC_SDATA0).
General-Purpose Input (MP1).
Serial Data Output 1 (ADC_SDATA1).
Master Clock Output/Clock for the Digital Microphone Input (CLKOUT).
General-Purpose Input (MP6).
Digital Microphone Stereo Input 2 and Digital Microphone Stereo Input 3 (DMIC2_3).
General-Purpose Input (MP5).
Digital Microphone Stereo Input 0 and Digital Microphone Stereo Input 1 (DMIC0_1).
General-Purpose Input (MP4).
Crystal Clock Output. This pin is the output of the crystal amplifier and must not be used to
provide a clock to other ICs in the system. If a master clock output is needed, use CLKOUT
(Pin 35).
Crystal Clock Input (XTALI).
Master Clock Input (MCLKIN).
Rev. 0 | Page 15 of 92
ADAU1372
Pin
No.
40
Mnemonic
IOVDD
EP
1
Data Sheet
Type 1
PWR
Description
Supply for Digital Input and Output Pins. The digital output pins are supplied from IOVDD,
and IOVDD sets the highest input voltage that can be present on the digital input pins. The
current draw of this pin is variable because it is dependent on the loads of the digital
outputs. Decouple IOVDD to DGND with a 0.1 µF capacitor.
Exposed Pad. The exposed pad is connected internally to the ADAU1372 grounds. For
increased reliability of the solder joints and maximum thermal capability, it is
recommended that the pad be soldered to the ground plane. See the Exposed Pad PCB
Design section for more information.
D_IO is digital input/output, D_IN is digital input, A_OUT is analog output, PWR is power, and A_IN is analog input.
Rev. 0 | Page 16 of 92
Data Sheet
ADAU1372
TYPICAL PERFORMANCE CHARACTERISTICS
0.04
300
0.02
280
260
0
240
220
GROUP DELAY (µs)
–0.04
–0.06
–0.08
–0.10
–0.12
180
160
140
120
100
80
–0.14
60
–0.16
40
–0.18
20
1k
100
0
12702-008
–0.20
10k
FREQUENCY (Hz)
0
2
4
6
8
10
12
14
16
18
20
FREQUENCY (kHz)
Figure 8. Relative Level vs. Frequency,
fS = 48 kHz, Signal Path = AIN0 to ASRC to ADC_SDATA0
Figure 11. Group Delay vs. Frequency,
fS = 48 kHz, Signal Path = AIN0 to ASRC to ADC_SDATA0
10
200
100
0
0
–10
–100
–20
PHASE (Degrees)
–200
PHASE (Degrees)
200
12702-011
RELATIVE LEVEL (dB)
–0.02
–300
–400
–500
–600
–700
–800
–30
–40
–50
–60
–70
–900
–80
–90
–1200
–100
2
4
6
8
10
12
14
16
18
FREQUENCY (kHz)
20
0
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
FREQUENCY (kHz)
Figure 9. Phase vs. Frequency, 20 kHz Bandwidth,
fS = 48 kHz, Signal Path = AIN0 to ASRC to ADC_SDATA0
Figure 12. Phase vs. Frequency, 2 kHz Bandwidth,
fS = 48 kHz, Signal Path = AIN0 to ASRC to ADC_SDATA0
0.4
300
0.2
280
0
260
240
–0.2
220
GROUP DELAY (µs)
–0.4
–0.6
–0.8
–1.0
–1.2
–1.4
200
180
160
140
120
100
80
–1.6
60
–1.8
40
–2.0
20
–2.2
100
1k
10k
FREQUENCY (Hz)
12702-010
RELATIVE LEVEL (dB)
0.2
Figure 10. Relative Level vs. Frequency,
fS = 96 kHz, Signal Path = AIN0 to ASRC to ADC_SDATA0
0
0
4
8
12
16
20
24
28
32
36
FREQUENCY (kHz)
Figure 13. Group Delay vs. Frequency,
fS = 96 kHz, Signal Path = AIN0 to ASRC to ADC_SDATA0
Rev. 0 | Page 17 of 92
40
12702-013
0
12702-009
–1100
12702-012
–1000
Data Sheet
PHASE (Degrees)
0
4
8
12
16
20
24
28
32
36
40
FREQUENCY (kHz)
0
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
Figure 17. Phase vs. Frequency, 2 kHz Bandwidth,
fS = 96 kHz, Signal Path = AIN0 to ASRC to ADC_SDATA0
2
300
0
280
260
–2
240
–4
220
GROUP DELAY (µs)
–6
–8
–10
–12
–14
200
180
160
140
120
100
80
–16
60
–18
40
–20
1k
0
12702-015
100
10k
FREQUENCY (Hz)
0
10
0
5
0
–400
–5
PHASE (Degrees)
–200
–600
–800
–1000
–1600
–35
–1800
60
70
FREQUENCY (kHz)
80
12702-016
–30
50
60
70
80
–20
–25
40
50
–15
–1400
30
40
–10
–1200
20
30
Figure 18. Group Delay vs. Frequency,
fS = 192 kHz, Signal Path = AIN0 to ASRC to ADC_SDATA0
200
10
20
FREQUENCY (kHz)
Figure 15. Relative Level vs. Frequency,
fS = 192 kHz, Signal Path = AIN0 to ASRC to ADC_SDATA0
0
10
12702-018
20
–22
Figure 16. Phase vs. Frequency, 80 kHz Bandwidth,
fS = 192 kHz, Signal Path = AIN0 to ASRC to ADC_SDATA0
–40
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
FREQUENCY (kHz)
Figure 19. Phase vs. Frequency, 2 kHz Bandwidth,
fS = 192 kHz, Signal Path = AIN0 to ASRC to ADC_SDATA0
Rev. 0 | Page 18 of 92
2.0
12702-019
RELATIVE LEVEL (dB)
0.2
FREQUENCY (kHz)
Figure 14. Phase vs. Frequency, 40 kHz Bandwidth,
fS = 96 kHz, Signal Path = AIN0 to ASRC to ADC_SDATA0
PHASE (Degrees)
5
0
–5
–10
–15
–20
–25
–30
–35
–40
–45
–50
–55
–60
–65
–70
12702-017
10
200
100
0
–100
–200
–300
–400
–500
–600
–700
–800
–900
–1000
–1100
–1200
–1300
–1400
–1500
12702-014
PHASE (Degrees)
ADAU1372
Data Sheet
ADAU1372
0.02
300
0.01
280
260
0
240
220
GROUP DELAY (µs)
–0.02
–0.03
–0.04
–0.05
–0.06
180
160
140
120
100
80
–0.07
60
–0.08
40
–0.09
0
12702-020
1k
100
10k
FREQUENCY (Hz)
0
2
4
6
8
10
12
14
16
18
20
FREQUENCY (kHz)
Figure 20. Relative Level vs. Frequency,
fS = 48 kHz, Signal Path = DAC_SDATA to ASRC to LOUTLx
12702-023
20
–0.10
Figure 23. Group Delay vs. Frequency,
fS = 48 kHz, Signal Path = DAC_SDATA to ASRC to LOUTLx
10
200
100
0
0
–10
–100
–20
–200
–300
PHASE (Degrees)
PHASE (Degrees)
200
–400
–500
–600
–700
–800
–30
–40
–50
–60
–70
–80
–900
–90
–1000
–1100
–100
–1200
–110
0
2
4
6
8
10
12
14
16
18
FREQUENCY (kHz)
20
–120
12702-021
–1300
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
FREQUENCY (kHz)
Figure 21. Phase vs. Frequency, 20 kHz Bandwidth,
fS = 48 kHz, Signal Path = DAC_SDATA to ASRC to LOUTLx
12702-024
RELATIVE LEVEL (dB)
–0.01
Figure 24. Phase vs. Frequency, 2 kHz Bandwidth,
fS = 48 kHz, Signal Path = DAC_SDATA to ASRC to LOUTLx
0.2
300
280
0.1
220
GROUP DELAY (µs)
240
–0.1
–0.2
–0.3
–0.4
–0.5
200
180
160
140
120
100
–0.6
80
–0.7
60
40
–0.8
100
1k
10k
FREQUENCY (Hz)
Figure 22. Relative Level vs. Frequency,
fS = 96 kHz, Signal Path = DAC_SDATA to ASRC to LOUTLx
0
0
4
8
12
16
20
24
28
32
36
FREQUENCY (kHz)
Figure 25. Group Delay vs. Frequency,
fS = 96 kHz, Signal Path = DAC_SDATA to ASRC to LOUTLx
Rev. 0 | Page 19 of 92
40
12702-025
20
–0.9
12702-022
RELATIVE LEVEL (dB)
260
0
PHASE (Degrees)
200
100
0
–100
–200
–300
–400
–500
–600
–700
–800
–900
–1000
–1100
–1200
–1300
–1400
–1500
–1600
–1700
4
8
12
16
20
24
28
32
36
40
FREQUENCY (kHz)
0
0.8
1.0
1.2
1.4
1.6
1.8
2.0
300
280
260
240
GROUP DELAY (µs)
220
200
180
160
140
120
100
80
60
40
1k
10k
0
FREQUENCY (Hz)
0
10
0
5
–200
0
–400
–5
–600
–10
PHASE (Degrees)
–800
–1000
–1200
–1400
–1600
–1800
–55
–2800
80
12702-028
–50
–2600
FREQUENCY (kHz)
80
–35
–45
70
70
–30
–2400
60
60
–25
–40
50
50
–20
–2200
40
40
–15
–2000
30
30
Figure 30. Group Delay vs. Frequency,
fS = 192 kHz, Signal Path = DAC_SDATA to ASRC to LOUTLx
200
20
20
FREQUENCY (kHz)
Figure 27. Relative Level vs. Frequency,
fS = 192 kHz, Signal Path = DAC_SDATA to ASRC to LOUTLx
10
10
12702-030
20
12702-027
RELATIVE LEVEL (dB)
0.6
Figure 29. Phase vs. Frequency, 2 kHz Bandwidth,
fS = 96 kHz, Signal Path = DAC_SDATA to ASRC to LOUTLx
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
–2.5
–3.0
–3.5
–4.0
–4.5
–5.0
–5.5
–6.0
–6.5
–7.0
–7.5
–8.0
100
PHASE (Degrees)
0.4
FREQUENCY (kHz)
Figure 26. Phase vs. Frequency, 40 kHz Bandwidth,
fS = 96 kHz, Signal Path = DAC_SDATA to ASRC to LOUTLx
0
0.2
Figure 28. Phase vs. Frequency, 80 kHz Bandwidth,
fS = 192 kHz, Signal Path = DAC_SDATA to ASRC to LOUTLx
–60
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
FREQUENCY (kHz)
Figure 31. Phase vs. Frequency, 2 kHz Bandwidth,
fS = 192 kHz, Signal Path = DAC_SDATA to ASRC to LOUTLx
Rev. 0 | Page 20 of 92
12702-031
0
10
5
0
–5
–10
–15
–20
–25
–30
–35
–40
–45
–50
–55
–60
–65
–70
–75
–80
12702-029
Data Sheet
12702-026
PHASE (Degrees)
ADAU1372
Data Sheet
ADAU1372
35
2
0
25
MAGNITUDE (dBFS)
20
15
10
–2
–4
–6
–8
5
–6
0
6
12
18
24
30
36
PGA GAIN SETTING (dB)
–10
12702-032
0
–12
0
5
10
15
FREQUENCY (kHz)
12702-035
INPUT IMPEDANCE (kΩ)
30
20
Figure 35. Decimation Pass Band Response, fS = 192 kHz
Figure 32. Input Impedance vs. PGA Gain Setting
(See the Input Impedance Section)
2
0
–20
MAGNITUDE (dBFS)
–2
–4
–6
–40
–60
–80
–100
–8
–120
0
5
10
15
0
12702-033
–10
20
FREQUENCY (kHz)
Figure 33. Decimation Pass Band Response, fS = 96 kHz
10
20
30
40
50
60
FREQUENCY (kHz)
70
80
90
100
12702-036
MAGNITUDE (dBFS)
0
Figure 36. Total Decimation Response, fs = 192 kHz,
Serial Port fS = 48 kHz
2
0
1
MAGNITUDE (dBFS)
–40
–60
–80
–100
0
–1
–2
–120
0
10
20
30
40
50
60
70
80
90
FREQUENCY (kHz)
100
Figure 34. Total Decimation Response, fS = 96 kHz,
Serial Port fS = 48 kHz
–4
0
5
10
15
FREQUENCY (kHz)
20
Figure 37. Interpolation Pass Band Response, fS = 96 kHz
Rev. 0 | Page 21 of 92
12702-037
–3
12702-034
MAGNITUDE (dBFS)
–20
ADAU1372
Data Sheet
3
0
2
MAGNITUDE (dBFS)
1
0
–1
–2
–40
–60
–80
–100
0
5
10
15
25
30
35
40
–120
12702-038
–3
45
FREQUENCY (kHz)
0
20
40
60
80
100
120
140
FREQUENCY (kHz)
12702-041
MAGNITUDE (dBFS)
–20
Figure 41. Total Decimation Response, fS = 96 kHz,
Serial Port fS = 192 kHz
Figure 38. Decimation Pass Band Response, fS = 96 kHz,
Serial Port fS = 96 kHz
3
0
2
MAGNITUDE (dBFS)
–40
–60
–80
–100
0
–1
–2
0
10
20
30
40
50
60
80
70
90
100
FREQUENCY (kHz)
–3
12702-039
–120
1
0
5
10
15
20
25
30
35
40
12702-042
MAGNITUDE (dBFS)
–20
45
FREQUENCY (kHz)
Figure 42. Decimation Pass Band Response, fS = 192 kHz,
Serial Port fS = 96 kHz
Figure 39. Total Decimation Response, fS = 96 kHz,
Serial Port fS = 96 kHz
10
0
8
MAGNITUDE (dBFS)
–20
4
2
0
–2
–4
–6
–40
–60
–80
–100
–10
–120
0
10
20
30
40
50
60
70
80
90
FREQUENCY (kHz)
0
10
20
30
40
50
60
80
90
FREQUENCY (kHz)
Figure 43. Total Decimation Response, fS = 192 kHz,
Serial Port fS = 96 kHz
Figure 40. Decimation Pass Band Response, fS = 96 kHz,
Serial Port fS = 192 kHz
Rev. 0 | Page 22 of 92
100
12702-043
–8
12702-040
MAGNITUDE (dBFS)
6
Data Sheet
ADAU1372
10
2
8
1
4
MAGNITUDE (dBFS)
MAGNITUDE (dBFS)
6
2
0
–2
–4
–6
0
–1
–2
–3
–8
10
20
30
40
50
60
70
80
90
–4
FREQUENCY (kHz)
0
0
0
–20
–20
MAGNITUDE (dBFS)
20
–40
–60
–80
–40
–60
–80
–100
40
60
80
100
120
140
FREQUENCY (kHz)
–120
12702-045
20
0
0
–20
–40
–60
–80
–120
30
40
50
60
70
FREQUENCY (kHz)
80
90
100
12702-046
–100
20
30
40
50
60
70
80
90
Figure 48. Total Interpolation Response, fS = 192 kHz
0
10
20
FREQUENCY (kHz)
Figure 45. Total Decimation Response, fS = 192 kHz,
Serial Port fS = 192 kHz
0
10
Figure 46. Total Interpolation Response, fS = 96 kHz
Rev. 0 | Page 23 of 92
100
12702-048
MAGNITUDE (dBFS)
15
Figure 47. Interpolation Pass Band Response, fS = 192 kHz
–100
MAGNITUDE (dBFS)
10
FREQUENCY (kHz)
Figure 44. Decimation Pass Band Response, fS = 192 kHz,
Serial Port fS = 192 kHz
–120
5
12702-047
0
12702-044
–10
ADAU1372
Data Sheet
THEORY OF OPERATION
The ADAU1372 is a low power audio codec that is ideal for
portable applications that require high quality audio, low power,
small size, and low latency. The four ADC and two DAC channels
each have an SNR of at least 94 dB and a THD + N of at least
−88 dB. The serial data port is compatible with I2S, left justified,
right justified, and TDM modes, with tristating for interfacing
to digital audio data. The operating voltage range is 1.8 V to 3.3 V,
with an on-board regulator generating the internal digital
supply voltage. If desired, the regulator can be powered down
and the voltage can be supplied externally.
The input signal path includes flexible configurations that can
accept single-ended analog microphone inputs as well as up to
four channels of digital microphone inputs. Two microphone bias
pins provide seamless interfacing to electret microphones. Each
input signal has its own PGA for volume adjustment.
The ADCs and DACs are high quality, 24-bit Σ-Δ converters
that operate at a selectable 192 kHz or 96 kHz sampling rate.
The ADCs have an optional high-pass filter with a cutoff
frequency of 1 Hz, 4 Hz, or 8 Hz. The ADCs and DACs also
include very fine step digital volume controls.
The stereo DAC output can differentially drive a headphone
earpiece speaker with 16 Ω impedance or higher. One side of
the differential output can be powered down if single-ended
operation is required. There is also the option to change to line
output mode when the output is lightly loaded.
The SigmaStudio™ software can be used to control the registers
through the control port. SigmaStudio allows an easy graphical
interface to control the signal flow; the tool can be used to
configure all of the ADAU1372 registers.
The ADAU1372 can generate its internal clocks from a wide range
of input clocks by using the on-board fractional PLL. The PLL
accepts inputs from 8 MHz to 27 MHz. For standalone operation,
the clock can be generated using the on-board crystal oscillator.
The ADAU1372 is provided in a small, 40-lead, 6 mm × 6 mm
LFCSP with an exposed bottom pad.
Rev. 0 | Page 24 of 92
Data Sheet
ADAU1372
SYSTEM CLOCKING AND POWER-UP
PLL Enabled Setup
The ADAU1372 must be powered up and initialized in the
proper sequence. The power-up details are outlined in the
Power Sequencing section. After power up, the clocks must be
properly configured and applied before writing to any registers
addresses above Register 0x06. See the Clock Initialization section
for details.
After the clocks are enabled, the ADCs, DACs, and multifunction
pins can be set up for the desired operation.
Finally, the serial ports and ASRCs must be set up and initialized.
See the Serial Port Initialization section for more details.
CLOCK INITIALIZATION
The ADAU1372 can generate its clocks either from an externally
provided clock or from a crystal oscillator. In both cases, the onboard PLL can be used or the clock can be fed directly to the
internal blocks. When a crystal oscillator is used, it is desirable
to use a 12.288 MHz crystal, and the crystal oscillator function
must be enabled in the MCLK_EN bit (Register 0x00, Bit 0). If
the PLL is used, it must always be set to output 24.576 MHz.
The PLL can be bypassed if a clock of 12.288 MHz or 24.576 MHz
is available in the system. Bypassing the PLL saves system power.
Set the CC_MDIV bit (Register 0x00, Bit 1) such that the internal
master clock is always 12.288 MHz; for example, when using a
24.576 MHz external source clock or if using the PLL, it is
necessary to use the internal divide by 2 (see Table 11).
The CC_MDIV bit must not be changed after setup; however,
the CLKSRC bit (Register 0x00, Bit 3) can be switched while the
internal master clock is enabled.
Table 11. Clock Configuration Settings
CC_MDIV
1
0
Description
Divide the PLL/external clock by 1. Use this setting
for a 12.288 MHz direct input clock source.
Divide the PLL/external clock by 2. Use this setting
for a 24.576 MHz direct input clock source or if using
the PLL.
PLL Bypass Setup
On power up, the ADAU1372 exits an internal reset after 12 ms.
The rate of the internal master clock must be set properly using
the CC_MDIV bit in the clock control register. When bypassing
the PLL, the clock fed into the MCLKIN pin must be either
12.288 MHz or 24.576 MHz. The internal master clock of the
ADAU1372 is disabled and no register writes can be performed
above Register 0x06 until the MCLK_EN bit is asserted.
The internal master clock of the ADAU1372 is disabled by the
default setting of the MCLK_EN bit and must remain disabled
during the PLL lock acquisition period. The user can poll the
lock bit (Register 0x06, Bit 0) to determine when the PLL has
locked. After lock is acquired, the ADAU1372 can be started by
asserting the MCLK_EN bit. This bit enables the master clock for
all the internal blocks of the ADAU1372.
To program the PLL during initialization or reconfiguration of
the codec, the following procedure must be followed:
1.
2.
3.
4.
5.
Ensure that PLL_EN (Register 0x00, Bit 7) is set low.
Set or reset the PLL control registers (Register 0x01 to
Register 0x05).
Enable the PLL using the PLL_EN bit.
Poll the PLL lock bit (Register 0x06, Bit 0).
Set the MCLK_EN bit in Register 0x00 after PLL lock is
acquired.
Control Port Access During Initialization
During the lock acquisition period, only Register 0x00 to
Register 0x06 are accessible through the control port. A read or
write to any other register is prohibited until the master clock
enable bit and the lock bit are both asserted.
PLL
The PLL uses the MCLKIN signal as a reference to generate
the internal master clock (MCLK). The PLL settings are set in
Register 0x00 to Register 0x05. Depending on the MCLK
frequency, the PLL must be set for either integer or fractional
mode. The PLL can accept input frequencies in the range of
8 MHz to 27 MHz.
TO PLL
CLOCK DIVIDER
MCLK
÷X
× (R + N/M)
12702-050
INITIALIZATION
Figure 49. PLL Block Diagram
Input Clock Divider
Before reaching the PLL, the input clock signal goes through an
integer clock divider to ensure that the clock frequency is within
a suitable range for the PLL. The X bits in the PLL_CTRL4 register
(Register 0x05, Bits[2:1]) set the PLL input clock divide ratio.
Integer Mode
Integer mode is used when the clock input is an integer multiple
of the PLL output.
For example, if MCLKIN = 12.288 MHz and (X + 1) = 1, and
fS = 48 kHz, then
PLL Required Output = 24.576 MHz
R/2 = 24.576 MHz/12.288 MHz = 2
where R/2 = 2 or R = 4.
Rev. 0 | Page 25 of 92
ADAU1372
Data Sheet
the input clock was previously divided by 2 using the
CC_MDIV bit. Note that the CLKOUT function is multiplexed
with the ADC_SDATA1 serial port output. Therefore, using the
CLKOUT function disables the ADC_SDATA1 serial port output.
In integer mode, the values set for N and M are ignored.
Table 12 lists common integer PLL parameter settings for
48 kHz sampling rates.
Fractional Mode
POWER SEQUENCING
Fractional mode is used when the clock input is a fractional
multiple of the PLL output.
AVDD and IOVDD can each be set to any voltage between 1.8 V
and 3.3 V, and DVDD can be set between 1.1 V and 1.8 V or
between 1.1 V and 1.2 V if using the on-board regulator.
For example, if MCLKIN = 13 MHz, (X + 1) = 1, and fS =
48 kHz,
PLL Required Output = 24.576 MHz
(1/2) × (R + (N/M)) = 24.576 MHz/13 MHz = (1/2) × (3 +
(1269/1625))
where:
R=3
N = 1269
M = 1625
On power-up, AVDD must be powered up before or at the same
time as IOVDD. IOVDD must not be powered up when power is
not applied to AVDD.
Enabling the PD pin powers down all analog and digital circuits.
Before enabling PD (that is, setting it low), mute the outputs to
avoid any pops when the IC is powered down.
PD can be tied directly to IOVDD for normal operation.
Table 13 lists common fractional PLL parameter settings for
48 kHz sampling rates. When the PLL is used in fractional
mode, the N/M fraction must be kept in the range of 0.1 to 0.9
to ensure correct operation of the PLL.
Power-Down Considerations
The PLL output clock must be in the range of 20.5 MHz to
27 MHz, which must be taken into account when calculating PLL
values and MCLK frequencies.
CLOCK OUTPUT
The CLKOUT pin can be used as a master clock output to clock
other ICs in the system or as the clock for the digital microphone
inputs. This clock can be generated from the 12.288 MHz master
clock of the ADAU1372 by factors of 2, 1, ½, ¼, and ⅛. If PDM
mode is enabled, only ½, ¼, and ⅛ settings produce a clock signal
on CLKOUT. The factor of 2 multiplier works properly only if
When powering down the ADAU1372, mute the outputs before
AVDD power is removed; otherwise, pops or clicks may be heard.
The easiest way to achieve this is to use a regulator that has a
power-good (PGOOD) signal to power the ADAU1372 or
generate a power-good signal using additional circuitry external
to the regulator itself. Typically, on such regulators the power-good
signal changes state when the regulated voltage drops below ~90%
of its target value. Connect this power-good signal to one of the
ADAU1372 multipurpose pins and mute the DAC outputs by
setting the multipurpose pin functionality to mute both DACs
in Register 0x38 to Register 0x3E. This ensures that the outputs
are muted before power is completely removed.
Table 12. Integer PLL Parameter Settings for PLL Output = 24.576 MHz
MCLK Input (MHz)
12.288
24.576
Input Divider
(X + 1)
1
1
Integer (R)
4
2
Denominator (M)
Don’t care
Don’t care
Numerator (N)
Don’t care
Don’t care
PLL_CTRL4 Settings
(Register 0x05)
0x20
0x10
Table 13. Fractional PLL Parameter Settings for PLL Output = 24.576 MHz
MCLK
Input
(MHz)
8
13
14.4
19.2
26
27
Input
Divider
(X + 1)
1
1
2
2
2
2
Integer
(R)
6
3
6
5
3
3
Denominator
(M)
125
1625
75
25
1625
1125
Numerator
(N)
18
1269
62
3
1269
721
PLL_CTRL4
(Reg. 0x05)
0x31
0x19
0x33
0x2B
0x1B
0x1B
PLL Parameter Register Settings
(Register 0x05 to Register 0x01)
PLL_CTRL3
PLL_CTRL2
PLL_CTRL1
(Reg. 0x04)
(Reg. 0x03)
(Reg. 0x02)
0x12
0x00
0x7D
0xF5
0x04
0x59
0x3E
0x00
0x4B
0x03
0x00
0x19
0xF5
0x04
0x59
0xD1
0x02
0x65
Rev. 0 | Page 26 of 92
PLL_CTRL0
(Reg. 0x01)
0x00
0x06
0x00
0x00
0x06
0x04
Data Sheet
ADAU1372
SIGNAL ROUTING
Figure 50 details the possible signal routing paths. The DAC
outputs can derive their inputs only from the DAC_SDATA
serial digital input. It is not possible to directly route the ADCs
to the DACs, with the exception of talkthrough mode; see the
Talkthrough Mode section for further details. However, the
DAC_SDATA input can be merged with the ADC data into a
AIN0
AIN1REF
AIN1
DMIC0_1/MP4
DMIC2_3/MP5
AIN2REF
AIN2
AIN3REF
AIN3
DAC_SDATA
PGA
PGA
ADC
MODULATOR
ADC
MODULATOR
ADC
DECIMATOR
QUAD
OUTPUT
ASRCS
ADC
DECIMATOR
SERIAL
OUTPUT
PORT
DIGITAL
MICROPHONE
INPUTS
PGA
PGA
ADC
MODULATOR
ADC
MODULATOR
ADC_SDATA0
ADC_SDATA1
ADC
DECIMATOR
ADC
DECIMATOR
SERIAL
INPUT PORT
STEREO INPUT
ASRC
DAC
OUTPUT
SELECTION
DAC
DAC
HPOUTLP/LOUTLP
HPOUTLN/LOUTLN
HPOUTRP/LOUTRP
HPOUTRN/LOUTRN
12702-051
AIN0REF
TDM serial output stream. This allows the daisy-chaining of
two ADAU1372 devices into one 8-channel TDM (TDM8) serial
data stream. The placement of where each data-word appears in
the TDM data stream is selected using Register 0x13 through
Register 0x16.
Figure 50. Input and Output Signal Routing
Rev. 0 | Page 27 of 92
ADAU1372
Data Sheet
INPUT SIGNAL PATHS
ANALOG INPUTS
The ADAU1372 can accept both line level and microphone inputs.
Each of the four analog input channels can be configured in a
single-ended mode or a single-ended with PGA mode. There
are also inputs for up to four digital microphones. The analog
inputs are biased at AVDD/2. Connect unused input pins to the
CM pin or ac-couple them to ground.
ADAU1372
PGA
AINx
2kΩ
–12dB TO
+35.25dB
Figure 51. Single-Ended Microphone Configuration
Analog Line Inputs
Line level signals can be input on the AINx pins of the analog
inputs. Figure 52 shows a single-ended line input using the
AINx pins. Tie the AINxREF pins to the CM pin. When using a
single-ended line input, disable the PGA using the PGA_ENx
bits and disable the corresponding PGA pop suppression bit
using the POP_SUPPRESS register (Register 0x29).
ADAU1372
Signals routed through the PGAs are inverted. As a result, signals
input through the PGA are output from the ADCs with a polarity
that is opposite that of the input. Single-ended inputs are not
inverted. The ADCs are noninverting.
LINE INPUT 0
AIN0
LINE INPUT 1
AIN1
LINE INPUT 2
AIN2
LINE INPUT 3
AIN3
Figure 52. Single-Ended Line Inputs
Precharging Input Capacitors
The input impedance of the analog inputs varies with the gain of
the PGA. This impedance ranges from 0.68 kΩ at the +35.25 dB
gain setting to 32.0 kΩ at the −12 dB setting. The input impedance
on each pin, RIN, can be calculated as follows:
R IN 
CM
MICBIASx
Signal Polarity
Input Impedance
AINxREF
12702-052
MICROPHONE
12702-053
Four input paths, from either an ADC or a digital microphone,
can be routed to the quad output ASRC. The input sources (ADC
or digital microphone) must be configured in pairs (for example, 0
and 1 or 2 and 3), but each channel can be routed individually.
The serial input data can also be routed to the serial output port
which allows the daisy-chaining of two ADAU1372 devices to
combine eight channels of ADC inputs onto one TDM8 stream.
The DAC_SDATA serial inputs can also be routed to the quad
output ASRCs, but it is not recommended. The output ASRCs add
2.5 dB of gain; the sample rate does not need to be converted,
and there are only four channels of ASRC.
40
kΩ
10 ( Gain / 20 )  1
where Gain is set by PGA_GAINx.
The optional 10 dB PGA boost set in the PGA_x_BOOST bits
does not affect the input impedance. This is an alternative way of
increasing gain without decreasing input impedance; however, it
causes some degradation in performance.
Analog Microphone Inputs
For microphone signals, the ADAU1372 analog inputs can be
configured as single-ended with PGA mode.
The PGA settings are controlled in Register 0x23 to Register 0x26.
The PGA is enabled by setting the PGA_ENx bits.
Connect the AINxREF pins to the CM pin and connect the
microphone signal to the inverting inputs of the PGAs (AINx),
as shown in Figure 51.
Precharge amplifiers are enabled by default to charge large
series capacitors quickly on the inputs and outputs. Precharging
these capacitors prevents pops in the audio signal. The precharge
circuits are powered up by default on startup and can be disabled
in the POP_SUPPRESS register. The precharge amplifiers are automatically disabled when the PGA or headphone amplifiers are
enabled. For unused PGAs and headphone outputs, disable
these precharge amplifiers using the POP_SUPPRESS register.
The precharging time is dependent on the input/output series
capacitors. The impedance looking into the pin is 500 Ω in this
mode. However, at startup, the impedance looking into the pin
is dominated by the time constant of the CM pin because the
precharge amplifiers reference the CM voltage.
Microphone Bias
The ADAU1372 includes two microphone bias outputs: MICBIAS0
and MICBIAS1. These pins provide a voltage reference for electret
analog microphones. The MICBIASx pins also cleanly supply
voltage to digital or analog MEMS microphones with separate
power supply pins. The MICBIASx voltage is set in the microphone
bias control register (Register 0x2D). Using this register, the
MICBIAS0 or MICBIAS1 output can be enabled or disabled.
The gain options provide two possible voltages: 0.65 × AVDD
or 0.90 × AVDD.
Rev. 0 | Page 28 of 92
Data Sheet
ADAU1372
Many applications require enabling only one of the two bias
outputs. When many microphones are used in the system or
when the positioning of the microphones on the PCB does not
allow one pin to bias all microphones, enable both of the two
bias outputs.
DIGITAL MICROPHONE INPUT
When using a digital microphone connected to the DMIC0_1/MP4
and DMIC2_3/MP5 pins, the DCM_0_1 and DCM_2_3 bits in
Register 0x1D and Register 0x1E must be set to enable the digital
microphone signal paths. The pin functions must also be set to
digital microphone input in the corresponding pin mode registers
(Register 0x3C and Register 0x3D). The DMIC0/DMIC2 and
DMIC1/DMIC3 channels can be swapped (left/right swap) by
writing to the DMIC_SW0 and DMIC_SW1 bits in the ADC_
CONTROL2 and ADC_CONTROL3 registers (Register 0x1D
and Register 0x1E, respectively). In addition, the microphone
polarity can be reversed by setting the DMIC_POLx bits, which
reverses the phase of the incoming audio by 180°.
The digital microphone inputs are clocked from the CLKOUT pin.
The digital microphone data stream must be clocked by this pin
and not by a clock from another source, such as another audio IC,
even if the other clock is of the same frequency as the CLKOUT
pin. Note that the CLKOUT function is multiplexed with the
ADC_SDATA1 serial port output. Therefore, using the CLKOUT
function disables the ADC_SDATA1 serial port output.
The digital microphone signal bypasses the analog input path
and the ADCs and is routed directly into the decimation filters.
The digital microphone and the ADCs share digital filters and,
therefore, both cannot be used simultaneously. The digital microphone inputs are enabled in pairs. The ADAU1372 inputs can be
set for either four analog inputs, four digital microphone inputs, or
two analog inputs and two digital microphone inputs. Figure 53
depicts the digital microphone interface and signal routing.
Figure 53 shows two digital microphones connected to the
DMIC0_1 pin. These microphones can also be connected to
DMIC2_3 if that signal path is to be used for digital microphones.
If more than two digital microphones are to be used in a system,
then up to two microphones can be connected to both DMIC0_ 1
and DMIC2_3 and the CLKOUT signal is fanned out to the clock
input of all of the microphones.
ANALOG-TO-DIGITAL CONVERTERS
The ADAU1372 includes four 24-bit, Σ-Δ ADCs with a selectable
sample rate of 192 kHz or 96 kHz.
ADC Full-Scale Level
The full-scale input to the ADCs (0 dBFS) scales linearly with
AVDD. At AVDD = 3.3 V, the full-scale input level is 0.90 V rms.
Signal levels greater than the full-scale value cause the ADCs to
clip.
Digital ADC Volume Control
The volume setting of each ADC can be digitally attenuated in the
ADCx_VOLUME registers (Register 0x1F to Register 0x22). The
volume can be set between 0 dB and −95.625 dB in 0.375 dB steps.
The ADC volume can also be digitally muted in the ADC_
CONTROL0 and ADC_CONTROL1 registers (Register 0x1B and
Register 0x1C).
High-Pass Filter
A high-pass filter is available on the ADC path to remove dc offsets;
this filter can be enabled or disabled using the HP_x_x_EN bits
in Register 0x1D and Register 0x1E. At fS = 192 kHz, the corner
frequency of this high-pass filter can be set to 1 Hz, 4 Hz, or 8 Hz.
1.8V TO 3.3V
CLK
VDD
0.1µF
DATA
DIGITAL
MICROPHONE
ADAU1372
L/R SELECT GND
CLKOUT
CLK
DATA
DIGITAL
MICROPHONE
DMIC0_1
L/R SELECT GND
12702-054
VDD
0.1µF
Figure 53. Digital Microphone Interface Block Diagram
Rev. 0 | Page 29 of 92
ADAU1372
Data Sheet
OUTPUT SIGNAL PATHS
Pop and Click Suppression
Data from the serial input port can be routed to the serial
output port or to the stereo DAC.
On power-up, the precharge circuitry is enabled on all four
analog output pins to suppress pops and clicks. After power-up,
the precharge circuitry can be set to a low power mode using
the HP_POP_DISx bits in the POP_SUPRRESS register
(Register 0x29).
The analog outputs of the ADAU1372 can be configured as
differential or single-ended outputs. The analog output pins can
drive headphone or earpiece speakers. The line outputs can
drive a load of at least 10 kΩ or can be put into headphone
mode to drive headphones or earpiece speakers. The analog
output pins are biased at AVDD/2.
ANALOG OUTPUTS
Headphone Output
The output pins can be driven by either a line output driver or a
headphone driver by setting the HP_EN_L and HP_EN_R bits
in the headphone line output select register (Register 0x43). The
headphone outputs can drive a load of at least 16 Ω.
The precharge time depends on the value of the capacitor
connected to the CM pin and the RC time constant of the load
on the output pin. For a typical line output load, the precharge
time is between 2 ms and 3 ms. After this precharge time, the
HP_POP_DISx bits can be set to low power mode.
To avoid clicks and pops, mute all analog outputs that are in use
while changing any register settings that may affect the signal path.
These outputs can then be unmuted after the changes are made.
Headphone Output Power-Up Sequencing
Line Outputs
To prevent pops when turning on the headphone outputs, wait
at least 6 ms to unmute these outputs after enabling the headphone
output using the HP_EN_x bits. Waiting 6 ms allows an internal
capacitor to charge before these outputs are used. Figure 54
illustrates the headphone output power-up sequencing.
The analog output pins (HPOUTLP/LOUTLP, HPOUTLN/
LOUTLN, HPOUTRP/LOUTRP, and HPOUTRN/LOUTRN)
drive both differential and single-ended loads. In their default
settings, these pins can drive typical line loads of 10 kΩ or
greater.
When the line output pins are used in single-ended mode, use
the HPOUTLP/LOUTLP and HPOUTRP/LOUTRP pins to
output the signals, and power down the HPOUTLN/LOUTLN
and HPOUTRN/LOUTRN pins.
USER
DEFINED
6ms
HP_EN_L AND HP_EN_R
1 = HEADPHONE
DIGITAL-TO-ANALOG CONVERTERS
HP_MUTE_R AND HP_MUTE_L
00 = UNMUTE
12702-055
The ADAU1372 includes two 24-bit, Σ-Δ DACs.
INTERNAL
PRECHARGE
Figure 54. Headphone Output Power-Up Timing
Ground Centered Headphone Configuration
The headphone outputs can also be configured as ground
centered outputs by connecting coupling capacitors in series
with the output pins. Ground centered headphones must use
the AGND pin as the ground reference.
When the headphone outputs are configured as ground centered,
the capacitors create a high-pass filter on the outputs. The corner
frequency of this filter, which has an attenuation of 3 dB, is
calculated by the following formula:
f3dB = 1/(2π × R × C)
where :
R is the impedance of the headphones.
C is the capacitor value.
For a typical headphone impedance of 32 Ω and a 220 µF
capacitor, the corner frequency is 23 Hz.
DAC Full-Scale Level
The full-scale output from the DACs (0 dBFS) scales linearly with
AVDD. At AVDD = 3.3 V, the full-scale output level is 1.94 V rms
for a differential output or 0.97 V rms for a single-ended output.
Digital DAC Volume Control
The volume of each DAC can be digitally attenuated using the
DACx_VOLUME registers (Register 0x2F and Register 0x30). The
volume can be set to be between 0 dB and −95.625 dB in
0.375 dB steps.
ASYNCHRONOUS SAMPLE RATE CONVERTERS
The ADAU1372 includes asynchronous sample rate converters
(ASRCs) to enable synchronous full duplex operation of the serial
ports. One quad ASRC is available for the digital outputs, and one
stereo ASRC is available for the digital input signals.
The ASRCs can convert serial output data from the ADC rate to
192 kHz back down to 8 kHz. All intermediate frequencies and
ratios are also supported.
Rev. 0 | Page 30 of 92
Data Sheet
ADAU1372
CONTROL PORT
The ADAU1372 has both a 4-wire SPI control port and a 2-wire
I2C bus control port. Each can be used to set the registers. The
IC defaults to I2C mode but can be set to SPI control mode by
pulling the SS pin low three times. The SPI control mode can be
entered at any time after initialization. The ADAU1372 exits SPI
mode only when the PD pin is pulled low or the IC is powered
down. To prevent the device from entering SPI mode, tie the
ADDR0/SS pin high or low and do not connect it to a controller.
All addresses can be accessed in single address mode or burst
mode. The first byte (Byte 0) of a control port write contains the
7-bit address plus the R/W bit. The next two bytes (Byte 1 and
Byte 2) are the 16-bit subaddress of the register location within the
ADAU1372. All subsequent bytes, starting with Byte 3, contain
the data and the address automatically increments. Each register
is only one byte long. The exact formats for specific types of writes
are shown in Figure 57 and Figure 58.
Registers and bits shown as reserved in the register map read back
zeroes. When writing to these registers and bits, such as during a
burst write across a reserved register, or when writing to
reserved bits in a register with other used bits, write zeroes.
The control port pins are multifunctional, depending on the
mode in which the device is operating. Table 14 details these
multiple functions.
Table 14. Control Port Pin Functions
Pin
SCL/SCLK
SDA/MISO
ADDR1/MOSI
ADDR0/SS
I2C Mode
SCL, input
SDA, open-collector output
I2C Address Bit 1, input
I2C Address Bit 0, input
SPI Mode
SCLK, input
MISO, output
MOSI, input
SS, input
BURST MODE COMMUNICATION
Use burst mode addressing, in which the subaddresses are
automatically incremented, to write to several registers that are
in contiguous locations. This increment occurs automatically
after a single word write unless the control port communication
is stopped; that is, a stop condition is issued for I2C mode, or SS
is brought high for SPI mode.
I2C PORT
The ADAU1372 supports a 2-wire serial (I2C-compatible)
microprocessor bus driving multiple peripherals. I2C uses two
pins—serial data (SDA) and serial clock (SCL)—to carry data
between the ADAU1372 and the system I2C master controller.
In I2C mode, the ADAU1372 is always a slave on the bus.
Each slave device is recognized by a unique 7-bit address. The
ADAU1372 I2C address format is shown in Table 15. The LSB of
this first byte sent from the I2C master sets either a read or write
operation. Logic Level 1 corresponds to a read operation, and
Logic Level 0 corresponds to a write operation.
The ADDR0 pin and the ADDR1 pin set the LSBs of the I2C
address (see Table 16); therefore, each ADAU1372 can be set to
one of four unique addresses. This allows multiple ICs to exist
on the same I2C bus without address contention. The 7-bit I2C
addresses are shown in Table 16.
An I2C data transfer is always terminated by a stop condition.
Both SDA and SCL must have 2.0 kΩ pull-up resistors on the
lines connected to them. The voltage on these signal lines must
not be higher than IOVDD.
Table 15. I2C Address Format
Bit 6
0
Bit 5
1
Bit 4
1
Bit 3
1
Bit 2
1
Bit 1
ADDR1
Bit 0
ADDR0
Table 16. I2C Addresses
ADDR1
0
0
1
1
ADDR0
0
1
0
1
Slave Address
0x3C
0x3D
0x3E
0x3F
Addressing
Initially, each device on the I2C bus is in an idle state and
monitoring the SDA and SCL lines for a start condition and
the proper address. The I2C master initiates a data transfer by
establishing a start condition, defined by a high to low transition on
SDA while SCL remains high. This condition indicates that an
address/data stream follows. All devices on the bus respond to
the start condition and shift the next eight bits (the 7-bit address
plus the R/W bit) MSB first. The device that recognizes the
transmitted address responds by pulling the data line low during
the ninth clock pulse. This ninth bit is an acknowledge bit. All
other devices withdraw from the bus at this point and return to
the idle condition.
The R/W bit determines the direction of the data. A Logic 0 on
the LSB of the first byte indicates that the master is writing information to the peripheral, whereas a Logic 1 indicates that the
master is reading information from the peripheral after writing
the subaddress and repeating the start address. A data transfer
takes place until a stop condition is encountered. A stop condition
occurs when SDA transitions from low to high while SCL is held
high. Figure 55 shows the timing of an I2C write, and Figure 56
shows the timing of an I2C read.
Rev. 0 | Page 31 of 92
ADAU1372
Data Sheet
Stop and start conditions can be detected at any stage during the
data transfer. If these conditions are asserted out of sequence with
normal read and write operations, the ADAU1372 immediately
jumps to the idle condition. During a given SCL high period,
the user must only issue one start condition, one stop condition, or
a single stop condition followed by a single start condition. If
the user issues an invalid subaddress, the ADAU1372 does not
issue an acknowledge and returns to the idle condition. If the
user exceeds the highest subaddress while in auto-increment mode,
one of two actions is taken. In read mode, the ADAU1372 outputs
the highest subaddress register contents until the master device
issues a no acknowledge, indicating the end of a read. A no
acknowledge condition is where the SDA line is not pulled low
on the ninth clock pulse on SCL. If the highest subaddress location
is reached while in write mode, the data for the invalid byte is
not loaded into any subaddress register, a no acknowledge is
issued by the ADAU1372, and the device returns to the idle
condition.
SCL
0
SDA
1
1
START BY
MASTER
1
1
ADDR1 ADDR0
R/W
ACKNOWLEDGE
BY ADAU1372
FRAME 1
CHIP ADDRESS BYTE
ACKNOWLEDGE
BY ADAU1372
FRAME 2
SUBADDRESS BYTE 1
SCL
(CONTINUED)
FRAME 3
SUBADDRESS BYTE 2
ACKNOWLEDGE
BY ADAU1372
ACKNOWLEDGE
BY ADAU1372
FRAME 4
DATA BYTE 1
STOP BY
MASTER
12702-056
SDA
(CONTINUED)
Figure 55. I2C Write to the ADAU1372 Clocking and Data Format
SCL
SDA
0
1
1
1
1
ADDR1 ADDR0
R/W
ACKNOWLEDGE
BY ADAU1372
ACKNOWLEDGE
BY ADAU1372
START BY
MASTER
FRAME 1
CHIP ADDRESS BYTE
FRAME 2
SUBADDRESS BYTE 1
SCL
(CONTINUED)
SDA
(CONTINUED)
0
FRAME 3
SUBADDRESS BYTE 2
ACKNOWLEDGE
BY ADAU1372
1
REPEATED
START BY MASTER
1
1
1
ADDR1
ADDR0
R/W
ACKNOWLEDGE
BY ADAU1372
FRAME 4
CHIP ADDRESS BYTE
SCL
(CONTINUED)
ACKNOWLEDGE
BY ADAU1372
ACKNOWLEDGE STOP BY
BY ADAU1372
MASTER
FRAME 6
READ DATA BYTE 2
FRAME 5
READ DATA BYTE 1
Figure 56. I2C Read from the ADAU1372 Clocking and Data Format
Rev. 0 | Page 32 of 92
12702-057
SDA
(CONTINUED)
Data Sheet
ADAU1372
I2C Read and Write Operations
This command causes the ADAU1372 SDA pin to reverse and
begin driving data back to the master. The master then responds
every ninth pulse with an acknowledge pulse to the ADAU1372.
Figure 57 shows the format of a single-word write operation.
Every ninth clock pulse, the ADAU1372 issues an acknowledge
by pulling SDA low.
Figure 60 shows the format of a burst mode read sequence.
Figure 58 shows the format of a burst mode write sequence. The
timing of a single word read operation is shown in Figure 59. Note
that the first R/W bit is 0, indicating a write operation. This is
because the subaddress still must be written to set up the internal
address. After the ADAU1372 acknowledges the receipt of the
subaddress, the master must issue a repeated start command
followed by the chip address byte with the R/W set to 1 (read).
I2C ADDRESS,
R/W = 0
AS
SUBADDRESS HIGH
S = start bit
P = stop bit
AM = acknowledge by master
AS = acknowledge by slave
AS
SUBADDRESS LOW
AS
DATA BYTE 1
12702-058
S
Figure 57 to Figure 60 use the following abbreviations:
P
I2C ADDRESS,
R/W = 0
S
SUBADDRESS
HIGH
AS
AS
SUBADDRESS
LOW
AS
DATA BYTE 1
AS
DATA BYTE 2
AS
...
12702-059
Figure 57. Single-Word I2C Write Format
P
I2C ADDRESS,
R/W = 0
S
AS
SUBADDRESS
HIGH
AS
SUBADDRESS
LOW
AS
I2C ADDRESS,
R/W = 1
S
AS
DATA BYTE 1
P
12702-060
Figure 58. Burst Mode I2C Write Format
S
I2C ADDRESS,
R/W = 0
AS
SUBADDRESS
HIGH
AS
SUBADDRESS
LOW
AS
S
I2C ADDRESS,
R/W = 1
AS
Figure 60. Burst Mode I2C Read Format
Rev. 0 | Page 33 of 92
DATA BYTE 1
AM
DATA BYTE 2
AM
...
P
12702-061
Figure 59. Single Word I2C Read Format
ADAU1372
Data Sheet
SPI PORT
Subaddress
By default, the ADAU1372 is in I2C mode, but it can be put into
SPI control mode by pulling SS low three times. This can be accomplished by issuing three SPI writes, which are in turn ignored by the
ADAU1372. The next (fourth) SPI write is then latched into the
SPI port. The SPI control mode can be entered at any time after
initialization. The ADAU1372 exits SPI mode only when the PD
pin is pulled low or the IC is powered down.
The 16-bit subaddress word is decoded into a location of one of the
registers. This subaddress is the location of the appropriate register.
Data Bytes
The number of data bytes varies according to the type of write,
single or burst. During a single mode write, the subaddress is
written followed by the data for a single register location.
During a burst mode write, an initial subaddress is written
followed by a continuous sequence of data for consecutive
register locations.
The SPI port uses a 4-wire interface—consisting of the SS, SCLK,
MOSI, and MISO signals—and is always a slave port. The SS
signal goes low at the beginning of a transaction and high at the
end of a transaction. The SCLK signal latches MOSI on a low to
high transition. MISO data is shifted out of the ADAU1372 on the
falling edge of SCLK and must be clocked into a receiving device,
such as a microcontroller, on the SCLK rising edge. The MOSI
signal carries the serial input data, and the MISO signal is the
serial output data. The MISO signal remains tristated until a read
operation is requested. This allows other SPI-compatible
peripherals to share the same readback line.
A sample clocking diagram for a burst write mode SPI operation is
shown in Figure 61. A sample clocking diagram of a burst read
mode SPI operation is shown in Figure 62. The MISO pin goes
from tristate to being driven at the beginning of Byte 3. In this
example, Byte 0 to Byte 2 contain the addresses and the R/W bit
and the subsequent bytes carry the data.
BURST MODE COMMUNICATION
Burst mode addressing, in which the subaddresses are automatically incremented, can be used for writing to several registers that
are in contiguous locations. This increment occurs automatically
after a single word write unless the control port communication
is stopped (that is, a stop condition is issued for I2C, or SS is
brought high for SPI).
All SPI transactions have the same basic format shown in Table 17.
Timing diagrams are shown in Figure 61 and Figure 62. All data
must be written MSB first.
Read/Write
The first byte of an SPI transaction indicates whether the
communication is a read or a write with the R/W bit. The LSB
of this first byte determines whether the SPI transaction is a read
(Logic Level 1) or a write (Logic Level 0).
Table 17. Generic SPI Word Format
Byte 0
0000000, R/W
Byte 2
Register/memory address [7:0]
Byte 3
Data
Byte 4 1
Data
Continues to end of data.
SS
SCLK
MOSI
BYTE 1
BYTE 0
BYTE 2
BYTE 3
12702-062
Figure 61. SPI Write to the ADAU1372 Clocking and Data Format (Burst Write Mode)
SS
SCLK
MOSI
MISO
BYTE 0
BYTE 1
HIGH-Z
DATA
DATA
Figure 62. SPI Read from the ADAU1372 Clocking and Data Format (Burst Read Mode)
Rev. 0 | Page 34 of 92
DATA
HIGH-Z
12702-063
1
Byte 1
Register/memory address [15:8]
Data Sheet
ADAU1372
MULTIPURPOSE PINS
The ADAU1372 has five multipurpose pins that can be used for
serial data input/output, clock outputs, and control in a system
without a microcontroller. Each pin can be individually set to either
its default or multipurpose setting. The functions include pushbutton volume controls, ADC to DAC bypass mode, and
muting the outputs.
When the ADC and/or DAC volumes are controlled with the
push-buttons, the corresponding volume control registers no
longer allow control of the volume from the control port.
Therefore, writing to these volume control registers has no
effect on the codec volume level.
The function of each of these pins is set in Register 0x38 to
Register 0x3E. By default, each pin is configured as an input.
The MPx pins can be put into a mode to mute the ADCs or DACs.
When in this mode, mute is enabled when an MPx pin is set low.
The full combination of possible mutes for ADCs and DACs
using MPx pins are set in Register 0x38 to Register 0x3E.
MUTE
Table 18. Multipurpose Pin Functions
36
37
Secondary Pin Functions
Multipurpose control inputs
ADC_SDATA0, multipurpose
control inputs
ADC_SDATA1, CLKOUT, multipurpose control inputs
Multipurpose control inputs
Multipurpose control inputs
TALKTHROUGH MODE
When talkthrough mode is enabled, a direct path from the
ADC outputs to the DACs is set up to enable bypassing of any
signal processing being performed with an external DSP. The
talkthrough path is enabled by setting an MPx pin low. Figure 63
shows the ADC to DAC bypass path disabled, and Figure 64
shows the talkthrough path enabled by pressing the push-button
switch. The talkthrough feature works for both analog and
digital microphone inputs.
PUSH-BUTTON VOLUME CONTROLS
Talkthrough is enabled when a switch connected to an MPx pin
that is set to talkthrough mode is closed and the MPx pin signal
is pulled low. Pressing and holding the switch closed enables the
talkthrough signal path as defined in the talkthrough register
(Register 0x2A). The DAC volume control setting is switched
from the default gain setting to the new TALKTHROUGH_
GAINx_VAL register setting (Register 0x2B and Register 0x2C).
ADC to DAC bypass is enabled only on ADC0 and ADC1. The
ADC to DAC bypass signal path is from the output of ADCx to
the input of the DAC(s).
The ADC and DAC volume controls can be controlled with two
push-buttons: one for volume up and one for volume down. The
volume setting can either be changed with a click of the button or
be ramped by holding the button. The volume settings change
when the signal on the pin from the button goes from low to
high.
When in push-button mode, the initial volume level is set with
the PB_VOL_INIT_VAL bits (Register 0x3F, Bits[7:3]). By
default, MP1 acts as the push-button volume up and MP6 acts
as the push-button volume down; however, any of the MPx pins
can be set to act as the push-button up and push-button down
volume controls.
MPx
When talkthrough is enabled, the current DAC volume setting
is ramped down to −95.625 dB and the talkthrough bypass volume
setting is ramped up to avoid pops when switching paths.
ADAU1372
10kΩ
AINxREF
DAC AND HP
AMPLIFIER
PGA AND ADC
AINx
NORMAL
SETTING
HPOUTxP
HPOUTxN
SERIAL
PORTS
12702-064
35
Default Pin Function
DAC_SDATA
MP1 acts as push-button
volume up
MP6 acts as pushbutton volume down
DMIC2_3
DMIC0_1
Figure 63. Talkthrough Path Disabled
MPx
ADAU1372
10kΩ
AINxREF
DAC AND HP
AMPLIFIER
PGA AND ADC
AINx
TALKTHROUGH
SETTING
SERIAL
PORTS
Figure 64. Talkthrough Path Enabled
Rev. 0 | Page 35 of 92
HPOUTxP
HPOUTxN
12702-077
Pin
No.
33
34
ADAU1372
Data Sheet
SERIAL DATA INPUT/OUTPUT PORTS
The serial data input and output ports of the ADAU1372 can be set
to accept or transmit data in a 2-channel format or in a 4-channel
or 8-channel TDM stream mode to interface to external ADCs,
DACs, DSPs, and systems on chip (SOCs). Data is processed in
twos complement, MSB first format. The left channel data field
always precedes the right channel data field in the 2-channel
streams. In 8-channel TDM mode, the data channels are output
sequentially, starting with the channel set by the ADC_SDATA0_ST
and ADC_SDATA1_ST bits. The serial modes and the position
of the data in the frame are set in the serial data port (SAI_0,
SAI_1) and serial output control registers (SOUT_SOURCE_x_x,
Register 0x13 to Register 0x16).
The serial data clocks do not need to be synchronous with the
ADAU1372 master clock input, but the LRCLK and BCLK
clocks must be synchronous to each other. The LRCLK and
BCLK pins both clock the serial input and output ports. The
ADAU1372 can be set to be either the master or the slave in a
system. Because there is only one set of serial data clocks, the input
and output ports must always both be either master or slave.
The serial data control registers allow control of the clock polarity
and the data input modes. The valid data formats are I2S, left
justified, right justified (24- or 16-bit), PCM, and TDM. In all
modes except for the right justified modes, the serial port inputs
an arbitrary number of bits up to a limit of 24. Extra bits do not
cause an error, but they are truncated internally.
SERIAL PORT INITIALIZATION
After the clock initialization is complete and the MCLK_EN bit
in Register 0x00 is enabled, the serial ports can be initialized
and set up for the desired operational mode. See the System
Clocking and Power-Up section for more details on clock
initialization.
To initialize the ADC to serial data outputs ADC_SDATA0
and/or ADC_SDATA1, follow this procedure:
6.
7.
8.
9.
10.
11.
12.
13.
The serial port can operate with an arbitrary number of BCLK
transitions in each LRCLK frame. The LRCLK in TDM mode can
be input to the ADAU1372 either as a 50% duty cycle clock or as a
1 bit wide pulse. Table 19 lists the modes in which the serial
input/output port can function. When using low IOVDD (1.8 V)
with a high BCLK rate (12.288 MHz), a sample rate of 192 kHz,
or a TDM8 mode operating at a sample rate of 48 kHz, it is
recommended to use the high drive settings on the serial port
pins. The high drive strength effectively speeds up the transition
times of the waveforms, thereby improving the signal integrity
of the clock and data lines. These can be set in the
PAD_CONTROL4 register (Register 0x4C).
14.
Table 19. Serial Input/Output Port Master/Slave Mode
Capabilities
5.
Serial
Port fS
(kHz)
48
96
192
2-Channel Modes
(I2S, Left Justified,
Right Justified)
Yes
Yes
Yes
4-Channel
TDM
Yes
Yes
No
8-Channel
TDM
Yes
No
No
Set the MODE_MP1 register (Register 0x39) to 0x00 to
enable Serial Output 0.
Set the MODE_MP6 register (Register 0x3E) to 0x00 to
enable Serial Output 1.
Write 0xFF to the DECIM_PWR_MODES register
(Register 0x44) to enable all the ASRCs and the sync filters.
Enable ADC0 and ADC1 in the ADC_CONTROL2 register
(Register 0x1D).
Enable ADC2 and ADC3 in the ADC_CONTROL3 register
(Register 0x1E).
Enable the output ASRCs in the ASRC_MODE register
(Register 0x1A).
Select a source for the quad ASRCs using the ASRCO_
SOURCE_0_1 register (Register 0x18) and the ASRCO_
SOURCE_2_3 register (Register 0x19).
Unmute ADC0 and ADC1 in the ADC_CONTROL0 register
(Register 0x1B).
Unmute ADC2 and ADC3 in the ADC_CONTROL1 register
(Register 0x1C).
To initialize the serial data inputs to appear at the DAC outputs,
follow this procedure:
1.
2.
3.
4.
6.
7.
Table 20 describes the proper serial port settings for standard
audio data formats. More information about the settings in this
table can be found in the Serial Port Control 0 register and the
Serial Port Control 1 register (Register 0x32 and Register 0x33,
respectively) descriptions.
Rev. 0 | Page 36 of 92
Enable ASRC and DAC modulator power using the
INTERP_PWR_MODES register (Register 0x45).
Enable the input ASRCs in the ASRC_MODE register
(Register 0x1A).
Select DAC0 and DAC1 as the source for the input ASRCs
in the DAC_SOURCE_0_1 register (Register 0x11).
Enable the DACs in the DAC_CONTROL1 register
(Register 0x2E).
Enable the power to the HPOUTLP/LOUTLP output and
the HPOUTLN/LOUTLN output in the OP_STAGE_CTRL
register (Register 0x43).
Unmute the DACs using the DAC_CONTROL1 register
(Register 0x2E)
Unmute the headphone/line outputs using the
OP_STAGE_MUTES register (Register 0x31).
Data Sheet
ADAU1372
TRISTATING UNUSED CHANNELS
The tristating of inactive channels is set in the SAI_1 register
(Register 0x33), which offers the option of tristating or driving
the inactive channel.
Unused outputs can be tristated so that multiple ICs can drive a
single TDM line. This function is available only when the serial
ports of the ADAU1372 are operating in TDM mode. Inactive
channels can be set in the SOUT_CONTROL0 register
(Register 0x34).
In a 32-bit TDM frame with 24-bit data, the eight unused bits
are tristated. Inactive channels are also tristated for the full frame.
Table 20. Serial Port Data Format Settings
LRCLK Polarity
(LR_POL)
0
1
1
1
1
1
Format
I2S (See Figure 65)
Left Justified (See Figure 66)
Right Justified (See Figure 67 and Figure 68)
TDM (See Figure 69 and Figure 70)
PCM/DSP Short Frame Sync (See Figure 71)
PCM/DSP Long Frame Sync (See Figure 72)
1
LRCLK Type
(LR_MODE)
0
0
0
0 or 1
1
0
BCLK Polarity
(BCLKEDGE)1
0
0
0
0
X
X
MSB Position
(SDATA_FMT)
00
01
10 or 11
00
00
01
X means don’t care.
LRCLK
2
1
4
3
24
25
26
32
33
35
34
36
56
58
57
64
I2S (24-BIT)
MSB
MSB
LSB
12702-066
BCLK (64 × fS)
LSB
RIGHT CHANNEL
LEFT CHANNEL
Figure 65. I2S Mode, 16 Bits to 24 Bits per Channel
LRCLK
1
2
3
23
24
25
32
33
34
35
55
56
57
64
LEFT JUSTIFIED
(24-BIT)
MSB
MSB
LSB
12702-067
BCLK (64 × fS)
LSB
RIGHT CHANNEL
LEFT CHANNEL
Figure 66. Left Justified Mode, 16 Bits to 24 Bits per Channel
LRCLK
1
2
9
10
11
12
31
32
33
34
41
42
43
44
63
64
RIGHT JUSTIFIED
(24-BIT)
MSB
LSB
MSB
LSB
LEFT CHANNEL
RIGHT CHANNEL
12702-068
BCLK (64 × fS)
Figure 67. Right Justified Mode, 24 Bits per Channel
LRCLK
1
2
17
18
19
20
31
32
33
34
49
50
51
52
63
64
RIGHT JUSTIFIED
(24-BIT)
MSB
LSB
MSB
LEFT CHANNEL
LSB
RIGHT CHANNEL
Figure 68. Right Justified Mode, 16 Bits per Channel
Rev. 0 | Page 37 of 92
12702-069
BCLK (64 × fS)
ADAU1372
Data Sheet
LRCLK
256 BCLKs
BCLK
32 BCLKs
DATA
SLOT 1
SLOT 2
SLOT 3
SLOT 4
SLOT 5
SLOT 6
SLOT 7
SLOT 8
MSB
MSB – 1
MSB – 2
12702-070
LRCLK
BCLK
DATA
Figure 69. 8-Channel TDM Mode
LRCLK
BCLK
MSB TDM
DATA
MSB TDM
CH
0
8TH
CH
SLOT 1
SLOT 2
SLOT 3
SLOT 4
SLOT 5
SLOT 6
SLOT 7
12702-071
SLOT 0
32
BCLKs
Figure 70. 8-Channel TDM Mode, Pulse LRCLK
LRCLK
1
2
3
4
16
17
18
19
20
32
33
34
PCM (24-BIT)
MSB
LSB
MSB
12702-072
BCLK (64 × fS)
LSB
LEFT CHANNEL
RIGHT CHANNEL
Figure 71. PCM/DSP Mode, 16 Bits per Channel, Short Frame Sync
LRCLK
1
2
3
4
16
17
LSB
MSB
18
19
20
32
33
34
PCM (24-BIT)
MSB
LSB
RIGHT CHANNEL
LEFT CHANNEL
Figure 72. PCM/DSP Mode, 16 Bits per Channel, Long Frame Sync
Rev. 0 | Page 38 of 92
12702-073
BCLK (64 × fS)
Data Sheet
ADAU1372
APPLICATIONS INFORMATION
POWER SUPPLY BYPASS CAPACITORS
EXPOSED PAD PCB DESIGN
Bypass each analog and digital power supply pin to its nearest
appropriate ground pin with a single 0.1 µF capacitor. The connections to each side of the capacitor must be as short as possible,
and the trace must be routed on a single layer with no vias. For
maximum effectiveness, locate the capacitor equidistant from
the power and ground pins or slightly closer to the power pin if
equidistant placement is not possible. Make thermal connections
to the ground planes on the far side of the capacitor.
The ADAU1372 has an exposed pad on the underside of the
LFCSP. This pad couples the package to the PCB for heat
dissipation. When designing a board for the ADAU1372, give
special consideration to the following:
Bypass each supply signal on the board with a single bulk
capacitor (10 µF to 47 µF).
•
GND
A copper layer equal in size to the exposed pad must be on
all layers of the board, from top to bottom, and must
connect somewhere to a dedicated copper board layer (see
Figure 74).
Place vias to connect all layers of copper, allowing efficient
heat and energy conductivity. For an example, see Figure 75,
which has nine vias arranged in a 3 via × 3 via grid in the pad
area.
TOP
GROUND
POWER
BOTTOM
CAPACITOR
VIAS
TO VDD
12702-075
VDD
•
COPPER SQUARES
TO GND
12702-074
Figure 74. Exposed Pad Layout Example, Side View (Not to Scale)
Figure 73. Recommended Power Supply Bypass Capacitor Layout
LAYOUT
Pin 24 is the AVDD supply for the headphone amplifiers. If the
headphone amplifiers are enabled, the PCB trace to this pin must
be wider than traces to other pins to increase the current carrying
capacity. A wider trace must also be used for the headphone
output lines.
Use a single ground plane in the application layout. Place
components in an analog signal path away from digital signals.
12702-076
GROUNDING
Figure 75. Exposed Pad Layout Example, Top View (Not to Scale)
Rev. 0 | Page 39 of 92
ADAU1372
Data Sheet
SYSTEM BLOCK DIAGRAM
10µF
DC VOLTAGE SOURCE:
1.8V TO 3.3V
+
0.10µF
10µF
0.10µF
+
0.10µF
0.10µF
14
47µF
13
LEFT_AUDIO
16
10µF
15
AIN1REF
LRCLK
BCLK
DAC_SDATA/MP0
ADC_SDATA0/MP1
ADC_SDATA1/CLKOUT/MP6
AIN2REF
SYSTEM
CONTROLLER
31
32
33
34
35
SERIAL PORT AND
CONTROL INTERFACE
SWITCHES
AGND
XTALI/MCLKIN
CM
38
39
100Ω
22pF
22pF
12702-049
0.10µF
XTALO
PD
DGND
+
1
2
3
4
AIN3REF
11
10µF
24
AIN2
30
12
AVDD
SDA/MISO
SCL/SCLK
ADDR1/MOSI
ADDR0/SS
AIN1
DGND
27
AVDD
ADAU1372
18 AIN3
17
RIGHT HEADPHONE
AIN0
AIN0REF
RIGHT_AUDIO
10µF
LEFT HEADPHONE
EP
8
EP
9
47µF
19
10
AVDD
40
IOVDD
29
26
HPOUTRP/LOUTRP
25
HPOUTRN/LOUTRN
6
MICBIAS0
7 MICBIAS1
LEFT
MICROPHONE
RIGHT
MICROPHONE
DMIC2_3/MP5
AGND
2kΩ
22
HPOUTLP/LOUTLP
21
HPOUTLN/LOUTLN
DMIC0_1/MP4
20 AGND
2kΩ
36
5
1.0µF
37
23
CONTROL
INTERFACE
SWITCHES
DVDD
REG_OUT
28
0.10µF
Figure 76. ADAU1372 System Block Diagram with Analog Microphones
Rev. 0 | Page 40 of 92
Data Sheet
ADAU1372
REGISTER SUMMARY: LOW LATENCY CODEC
Table 21. Register Summary
Reg.
Name
Bits
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
0x00
CLK_CONTROL
[7:0]
PLL_EN
RESERVED
SPK_FLT_DIS
XTAL_DIS
CLKSRC
RESERVED
CC_MDIV
MCLK_EN
0x00
R/W
0x01
PLL_CTRL0
[7:0]
M_MSB
0x00
R/W
0x02
PLL_CTRL1
[7:0]
M_LSB
0x00
R/W
0x03
PLL_CTRL2
[7:0]
N_MSB
0x00
R/W
0x04
PLL_CTRL3
[7:0]
N_LSB
0x00
R/W
0x05
PLL_CTRL4
[7:0]
0x06
PLL_CTRL5
[7:0]
0x07
CLKOUT_SEL
[7:0]
0x08
REGULATOR
[7:0]
0x00
R/W
0x11
DAC_SOURCE_0_1
[7:0]
DAC_SOURCE1
DAC_SOURCE0
0x10
R/W
0x13
SOUT_SOURCE_0_1
[7:0]
SOUT_SOURCE1
SOUT_SOURCE0
0x54
R/W
0x14
SOUT_SOURCE_2_3
[7:0]
SOUT_SOURCE3
SOUT_SOURCE2
0x76
R/W
0x15
SOUT_SOURCE_4_5
[7:0]
SOUT_SOURCE5
SOUT_SOURCE4
0x54
R/W
0x16
SOUT_SOURCE_6_7
[7:0]
SOUT_SOURCE7
SOUT_SOURCE6
0x76
R/W
0x17
ADC_SDATA_CH
[7:0]
RESERVED
0x04
R/W
0x18
ASRCO_SOURCE_0_1 [7:0]
ASRC_OUT_SOURCE1
0x10
R/W
0x19
ASRCO_SOURCE_2_3 [7:0]
ASRC_OUT_SOURCE3
0x32
R/W
ASRC_IN_EN 0x00
R/W
RESERVED
R
X
RESERVED
RESERVED
PLL_TYPE
0x00
R/W
LOCK
0x00
R/W
0x00
R/W
CLKOUT_FREQ
RESERVED
REG_PD
REGV
ADC_SDATA1_ST
ADC_SDATA0_ST
ASRC_OUT_SOURCE0
ASRC_OUT_SOURCE2
RESERVED
ASRC_IN_CH
ASRC_OUT_EN
RW
0x1A ASRC_MODE
[7:0]
0x1B
ADC_CONTROL0
[7:0]
RESERVED
RESERVED
ADC1_MUTE
ADC0_MUTE
RESERVED
ADC_0_1_FS
0x19
R/W
0x1C ADC_CONTROL1
[7:0]
RESERVED
RESERVED
ADC3_MUTE
ADC2_MUTE
RESERVED
ADC_2_3_FS
0x19
R/W
0x1D ADC_CONTROL2
[7:0]
RESERVED
HP_0_1_EN
DMIC_POL0
DMIC_SW0
DCM_0_1
ADC_1_EN
ADC_0_EN
0x00
R/W
0x1E
ADC_CONTROL3
[7:0]
RESERVED
HP_2_3_EN
DMIC_POL1
DMIC_SW1
DCM_2_3
ADC_3_EN
ADC_2_EN
0x00
R/W
0x1F
ADC0_VOLUME
[7:0]
ADC_0_VOL
0x00
R/W
0x20
ADC1_VOLUME
[7:0]
ADC_1_VOL
0x00
R/W
0x21
ADC2_VOLUME
[7:0]
ADC_2_VOL
0x00
R/W
0x22
ADC3_VOLUME
[7:0]
0x00
R/W
0x23
PGA_CONTROL_0
[7:0]
PGA_EN0
PGA_MUTE0
ADC_3_VOL
PGA_GAIN0
0x40
R/W
0x24
PGA_CONTROL_1
[7:0]
PGA_EN1
PGA_MUTE1
PGA_GAIN1
0x40
R/W
0x25
PGA_CONTROL_2
[7:0]
PGA_EN2
PGA_MUTE2
PGA_GAIN2
0x40
R/W
0x26
PGA_CONTROL_3
[7:0]
PGA_EN3
PGA_MUTE3
0x27
PGA_STEP_CONTROL [7:0]
0x28
PGA_10DB_BOOST
[7:0]
0x29
POP_SUPPRESS
[7:0]
0x2A TALKTHROUGH
[7:0]
0x2B
TALKTHROUGH_
GAIN0
[7:0]
0x2C TALKTHROUGH_
GAIN1
[7:0]
0x2D MIC_BIAS
[7:0]
RESERVED
MIC_EN1
MIC_EN0
RESERVED
RESERVED
MIC_GAIN1
MIC_GAIN0
0x00
R/W
0x2E
DAC_CONTROL1
[7:0]
RESERVED
DAC_POL
DAC1_MUTE
DAC0_MUTE
RESERVED
DAC1_EN
DAC0_EN
0x18
R/W
0x2F
DAC0_VOLUME
[7:0]
0x00
R/W
0x30
DAC1_VOLUME
[7:0]
0x31
OP_STAGE_MUTES
[7:0]
0x32
SAI_0
[7:0]
0x33
SAI_1
[7:0]
TDM_TS
0x34
SOUT_CONTROL0
[7:0]
TDM7_DIS TDM6_DIS
0x38
MODE_MP0
[7:0]
0x40
R/W
SLEW_PD3
PGA_GAIN3
SLEW_PD2
SLEW_PD1
SLEW_PD0
0x00
R/W
PGA_3_BOOST
PGA_2_BOOST
PGA_1_BOOST
PGA_0_
BOOST
0x00
R/W
HP_POP_DIS1 HP_POP_DIS0 PGA_POP_DIS3 PGA_POP_DIS2
PGA_POP_DIS1
PGA_POP_
DIS0
0x3F
R/W
0x00
R/W
TALKTHROUGH_GAIN0_VAL
0x00
R/W
TALKTHROUGH_GAIN1_VAL
0x00
R/W
RESERVED
SLEW_RATE
RESERVED
RESERVED
RESERVED
TALKTHROUGH_PATH
DAC_0_VOL
DAC_1_VOL
RESERVED
SDATA_FMT
BCLK_TDMC
HP_MUTE_R
SAI
HP_MUTE_L
SER_PORT_FS
0x00
R/W
0x0F
R/W
0x00
R/W
LR_MODE
LR_POL
SAI_MSB
BCLKRATE
BCLKEDGE
SAI_MS
0x00
R/W
TDM5_DIS
TDM4_DIS
TDM3_DIS
TDM2_DIS
TDM1_DIS
TDM0_DIS
0x00
R/W
0x00
R/W
RESERVED
MODE_MP0_VAL
Rev. 0 | Page 41 of 92
ADAU1372
Data Sheet
Reg.
Name
Bits
0x39
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
RW
MODE_MP1
[7:0]
RESERVED
MODE_MP1_VAL
0x10
R/W
0x3C MODE_MP4
[7:0]
RESERVED
MODE_MP4_VAL
0x00
R/W
0x3D MODE_MP5
[7:0]
RESERVED
MODE_MP5_VAL
0x00
R/W
0x3E
MODE_MP6
[7:0]
RESERVED
MODE_MP6_VAL
0x11
R/W
0x3F
PB_VOL_SET
[7:0]
0x40
PB_VOL_CONV
[7:0]
0x41
DEBOUNCE_MODE
[7:0]
0x43
OP_STAGE_CTRL
[7:0]
0x44
DECIM_PWR_MODES [7:0]
0x45
INTERP_PWR_MODES
[7:0]
0x46
BIAS_CONTROL0
[7:0]
0x47
BIAS_CONTROL1
[7:0]
RESERVED CBIAS_DIS
0x48
PAD_CONTROL0
[7:0]
RESERVED DMIC2_3_PU DMIC0_1_PU
LRCLK_PU
BCLK_PU
ADC_SDATA1_PU
ADC_SDATA0_PU
0x49
PB_VOL_INIT_VAL
GAINSTEP
RAMPSPEED
HOLD
0x00
R/W
PB_VOL_CONV_VAL
0x87
R/W
DEBOUNCE
0x05
R/W
0x0F
R/W
RESERVED
RESERVED
DEC_3_EN DEC_2_EN
HP_EN_R
HP_EN_L
DEC_1_EN
DEC_0_EN
RESERVED
HP_IBIAS
HP_PDN_R
HP_PDN_L
SYNC_3_EN
SYNC_2_EN
SYNC_1_EN
SYNC_0_EN
0x00
R/W
MOD_1_EN
MOD_0_EN
INT_1_EN
INT_0_EN
0x00
R/W
R/W
AFE_IBIAS01
ADC_IBIAS23
ADC_IBIAS01
0x00
AFE_IBIAS23
MIC_IBIAS
DAC_IBIAS
0x00
R/W
DAC_
SDATA_PU
0x7F
R/W
PAD_CONTROL1
[7:0]
RESERVED
RESERVED
SCL_PU
SDA_PU
ADDR1_PU
ADDR0_PU
0x1F
R/W
0x4A PAD_CONTROL2
[7:0]
RESERVED DMIC2_3_PD DMIC0_1_PD
LRCLK_PD
BCLK_PD
ADC_SDATA1_PD
ADC_SDATA0_PD
DAC_
SDATA_PD
0x00
R/W
0x4B
RESERVED
RESERVED
SCL_PD
SDA_PD
ADDR1_PD
ADDR0_PD
0x00
R/W
LRCLK_DRV
BCLK_DRV
ADC_SDATA1_DRV ADC_SDATA0_DRV RESERVED
0x00
R/W
RESERVED
SCL_DRV
SDA_DRV
0x00
R/W
PAD_CONTROL3
[7:0]
0x4C PAD_CONTROL4
[7:0]
0x4D PAD_CONTROL5
[7:0]
RESERVED RESERVED
RESERVED
RESERVED
Rev. 0 | Page 42 of 92
RESERVED
RESERVED
Data Sheet
ADAU1372
REGISTER DETAILS: LOW LATENCY CODEC
CLOCK CONTROL REGISTER
Address: 0x00, Reset: 0x00, Name: CLK_CONTROL
This register enables the internal clocks.
Table 22. Bit Descriptions for CLK_CONTROL
Bits
Bit Name
7
PLL_EN
Settings
Description
Reset
Access
Enable PLL. When this bit is set to 0, the PLL is powered down and the PLL output
clock is disabled. The PLL must not be enabled until after all the PLL control settings
(Register PLL_CTRL0 to Register PLL_CTRL5) have been set. The PLL clock output is
active when both PLL_EN = 1 and MCLK_EN = 1.
0x0
R/W
0
PLL disabled.
1
PLL enabled.
6
RESERVED
Reserved.
0x0
R/W
5
SPK_FLT_DIS
Disable I C spike filter. By default, the SDA and SCL inputs have a 50 ns spike
suppression filter. When the control interface is in SPI mode, this filter is disabled
regardless of this setting.
0x0
R/W
0x0
R/W
0x0
R/W
4
3
2
0
I2C spike filter enabled.
1
I2C spike filter disabled.
XTAL_DIS
Disable crystal oscillator.
0
Crystal oscillator enabled.
1
Crystal oscillator disabled.
CLKSRC
Main clock source.
0
External pin drives main clock.
1
PLL drives main clock. This bit must only be set after LOCK in Register PLL_CTRL5
has gone high.
2
RESERVED
Reserved.
0x0
R/W
1
CC_MDIV
MCLK divider control. The internal master clock (MCLK) of the IC is used by all digital
logic. It must run at 12.288 MHz.
0x0
R/W
0x0
R/W
0
0
Divide by 2: divide PLL/external clock by 2.
1
Divide by 1: divide PLL/external clock by 1.
MCLK_EN
Master clock enable. When MCLK_EN = 0, it is only possible to write to this register and
the PLL control registers (PLL_CTRL0 to PLL_CTRL5). This control also enables the PLL
clock. If using the PLL, do not set MCLK_EN = 1 until LOCK in Register PLL_CTRL5 is 1.
0
Main clock disabled.
1
Main clock enabled.
Rev. 0 | Page 43 of 92
ADAU1372
Data Sheet
PLL DENOMINATOR MSB REGISTER
Address: 0x01, Reset: 0x00, Name: PLL_CTRL0
This register must only be written when PLL_EN = 0 in Register CLK_CONTROL.
Table 23. Bit Descriptions for PLL_CTRL0
Bits
Bit Name
[7:0]
M_MSB
Settings
Description
Reset
Access
PLL denominator MSB
0x0
R/W
Description
Reset
Access
PLL denominator LSB
0x0
R/W
Description
Reset
Access
PLL numerator MSB
0x0
R/W
Description
Reset
Access
PLL numerator LSB
0x0
R/W
PLL DENOMINATOR LSB REGISTER
Address: 0x02, Reset: 0x00, Name: PLL_CTRL1
This register must only be written when PLL_EN = 0 in Register CLK_CONTROL.
Table 24. Bit Descriptions for PLL_CTRL1
Bits
Bit Name
[7:0]
M_LSB
Settings
PLL NUMERATOR MSB REGISTER
Address: 0x03, Reset: 0x00, Name: PLL_CTRL2
This register must only be written when PLL_EN = 0 in Register CLK_CONTROL.
Table 25. Bit Descriptions for PLL_CTRL2
Bits
Bit Name
[7:0]
N_MSB
Settings
PLL NUMERATOR LSB REGISTER
Address: 0x04, Reset: 0x00, Name: PLL_CTRL3
This register must only be written when PLL_EN = 0 in Register CLK_CONTROL.
Table 26. Bit Descriptions for PLL_CTRL3
Bits
Bit Name
[7:0]
N_LSB
Settings
Rev. 0 | Page 44 of 92
Data Sheet
ADAU1372
PLL INTEGER SETTING REGISTER
Address: 0x05, Reset: 0x00, Name: PLL_CTRL4
This register must only be written when PLL_EN = 0 in Register CLK_CONTROL.
Table 27. Bit Descriptions for PLL_CTRL4
Bits
Bit Name
7
[6:3]
[2:1]
0
Settings
Description
Reset
Access
RESERVED
Reserved.
0x0
R/W
R
PLL integer setting.
0x0
R/W
0x0
R/W
0x0
R/W
0000
Reserved.
0001
Reserved.
0010
2.
0011
3.
0100
4.
0101
5.
0110
6.
0111
7.
1000
8.
X
PLL input clock divide ratio.
00
Pin clock input/1.
01
Pin clock input/2.
10
Pin clock input/3.
11
Pin clock input/4.
PLL_TYPE
PLL type.
0
Integer.
1
Fractional.
Rev. 0 | Page 45 of 92
ADAU1372
Data Sheet
PLL LOCK FLAG REGISTER
Address: 0x06, Reset: 0x00, Name: PLL_CTRL5
Table 28. Bit Descriptions for PLL_CTRL5
Bits
Bit Name
Description
Reset
Access
[7:1]
RESERVED
Settings
Reserved.
0x0
R/W
0
LOCK
Flag to indicate if the PLL is locked. This bit is read only.
0x0
R
0
PLL unlocked.
1
PLL locked.
CLKOUT SETTING SELECTION REGISTER
Address: 0x07, Reset: 0x00, Name: CLKOUT_SEL
When Pin ADC_SDATA1/CLKOUT/MP6 is set to clock output mode, the frequency of the output clock is set here. CLKOUT can be used
to provide a master clock to another IC or the clock for digital microphones. The 12 MHz/24 MHz setting is used when clocking another
IC, 1.5 MHz/3 MHz when clocking digital microphones. The CLKOUT frequency is derived from the master clock frequency. The master
clock must always be 12.288 MHz.
Table 29. Bit Descriptions for CLKOUT_SEL
Bits
Bit Name
[7:3]
RESERVED
[2:0]
CLKOUT_FREQ
Settings
Description
Reset
Access
Reserved.
0x0
R/W
CLKOUT pin frequency.
0x0
R/W
000
Master clock × 2 (24.576 MHz).
001
Master clock (12.288 MHz).
010
Master clock/2 (6.144 MHz).
011
Master clock/4 (3.072 MHz).
100
Master clock/8 (1.536 MHz).
111
Clock output off = 0.
Rev. 0 | Page 46 of 92
Data Sheet
ADAU1372
REGULATOR CONTROL REGISTER
Address: 0x08, Reset: 0x00, Name: REGULATOR
Table 30. Bit Descriptions for REGULATOR
Bits
Bit Name
[7:3]
2
Settings
Description
Reset
Access
RESERVED
Reserved.
0x0
R/W
REG_PD
Powers down LDO regulator.
0x0
R/W
0x0
R/W
0
1
[1:0]
REGV
Regulator active.
Regulator powered down.
Set regulator output voltage.
00
1.2 V.
01
1.1 V.
10
Reserved.
11
Reserved.
DAC INPUT SELECT REGISTER
Address: 0x11, Reset: 0x10, Name: DAC_SOURCE_0_1
Table 31. Bit Descriptions for DAC_SOURCE_0_1
Bits
Bit Name
[7:4]
DAC_SOURCE1
Settings
Description
Reset
Access
DAC1 input source.
0x1
R/W
0000
Reserved.
0001
Reserved.
0010
Reserved.
0011
Reserved.
0100
Reserved.
0101
Reserved.
0110
Reserved.
0111
Reserved.
1000
Reserved.
1001
Reserved.
1010
Reserved.
1011
Reserved.
1100
Input ASRC Channel 0.
1101
Input ASRC Channel 1.
Rev. 0 | Page 47 of 92
ADAU1372
Bits
Bit Name
[3:0]
DAC_SOURCE0
Data Sheet
Settings
Description
Reset
Access
DAC0 input source.
0x0
R/W
0000
Reserved.
0001
Reserved.
0010
Reserved.
0011
Reserved.
0100
Reserved.
0101
Reserved.
0110
Reserved.
0111
Reserved.
1000
Reserved.
1001
Reserved.
1010
Reserved.
1011
Reserved.
1100
Input ASRC Channel 0.
1101
Input ASRC Channel 1.
SERIAL DATA OUTPUT 0/SERIAL DATA OUTPUT 1 INPUT SELECT REGISTER
Address: 0x13, Reset: 0x54, Name: SOUT_SOURCE_0_1
Table 32. Bit Descriptions for SOUT_SOURCE_0_1
Bits
Bit Name
[7:4]
SOUT_SOURCE1
Settings
Description
Reset
Access
Serial Data Output Channel 1 source select.
0x5
R/W
0000
Reserved.
0001
Reserved.
0010
Reserved.
0011
Reserved.
0100
Output ASRC Channel 0.
0101
Output ASRC Channel 1.
0110
Output ASRC Channel 2.
0111
Output ASRC Channel 3.
1000
Serial Input 0.
1001
Serial Input 1.
1010
Serial Input 2.
1011
Serial Input 3.
1100
Serial Input 4.
1101
Serial Input 5.
1110
Serial Input 6.
Rev. 0 | Page 48 of 92
Data Sheet
Bits
Bit Name
ADAU1372
Settings
1111
[3:0]
SOUT_SOURCE0
Description
Reset
Access
0x4
R/W
Serial Input 7.
Serial Data Output Channel 0 source select.
0000
Reserved.
0001
Reserved.
0010
Reserved.
0011
Reserved.
0100
Output ASRC Channel 0.
0101
Output ASRC Channel 1.
0110
Output ASRC Channel 2.
0111
Output ASRC Channel 3.
1000
Serial Input 0.
1001
Serial Input 1.
1010
Serial Input 2.
1011
Serial Input 3.
1100
Serial Input 4.
1101
Serial Input 5.
1110
Serial Input 6.
1111
Serial Input 7.
SERIAL DATA OUTPUT 2/SERIAL DATA OUTPUT 3 INPUT SELECT REGISTER
Address: 0x14, Reset: 0x76, Name: SOUT_SOURCE_2_3
Table 33. Bit Descriptions for SOUT_SOURCE_2_3
Bits
Bit Name
[7:4]
SOUT_SOURCE3
Settings
Description
Reset
Access
Serial Data Output Channel 3 source select.
0x7
R/W
0000
Reserved.
0001
Reserved.
0010
Reserved.
0011
Reserved.
0100
Output ASRC Channel 0.
0101
Output ASRC Channel 1.
0110
Output ASRC Channel 2.
0111
Output ASRC Channel 3.
1000
Serial Input 0.
1001
Serial Input 1.
1010
Serial Input 2.
Rev. 0 | Page 49 of 92
ADAU1372
Bits
[3:0]
Bit Name
Data Sheet
Settings
Description
Reset
Access
0x6
R/W
Description
Reset
Access
Serial Data Output Channel 5 source select.
0x5
R/W
1011
Serial Input 3.
1100
Serial Input 4.
1101
Serial Input 5.
1110
Serial Input 6.
1111
Serial Input 7.
SOUT_SOURCE2
Serial Data Output Channel 2 source select.
0000
Reserved.
0001
Reserved.
0010
Reserved.
0011
Reserved.
0100
Output ASRC Channel 0.
0101
Output ASRC Channel 1.
0110
Output ASRC Channel 2.
0111
Output ASRC Channel 3.
1000
Serial Input 0.
1001
Serial Input 1.
1010
Serial Input 2.
1011
Serial Input 3.
1100
Serial Input 4.
1101
Serial Input 5.
1110
Serial Input 6.
1111
Serial Input 7.
SERIAL DATA OUTPUT 4/SERIAL DATA OUTPUT 5 INPUT SELECT REGISTER
Address: 0x15, Reset: 0x54, Name: SOUT_SOURCE_4_5
Table 34. Bit Descriptions for SOUT_SOURCE_4_5
Bits
Bit Name
[7:4]
SOUT_SOURCE5
Settings
0000
Reserved.
0001
Reserved.
0010
Reserved.
0011
Reserved.
0100
Output ASRC Channel 0.
0101
Output ASRC Channel 1.
0110
Output ASRC Channel 2.
Rev. 0 | Page 50 of 92
Data Sheet
Bits
[3:0]
Bit Name
ADAU1372
Settings
Description
0111
Output ASRC Channel 3.
1000
Serial Input 0.
1001
Serial Input 1.
1010
Serial Input 2.
1011
Serial Input 3.
1100
Serial Input 4.
1101
Serial Input 5.
1110
Serial Input 6.
1111
Serial Input 7.
SOUT_SOURCE4
Serial Data Output Channel 4 source select.
0000
Reserved.
0001
Reserved.
0010
Reserved.
0011
Reserved.
0100
Output ASRC Channel 0.
0101
Output ASRC Channel 1.
0110
Output ASRC Channel 2.
0111
Output ASRC Channel 3.
1000
Serial Input 0.
1001
Serial Input 1.
1010
Serial Input 2.
1011
Serial Input 3.
1100
Serial Input 4.
1101
Serial Input 5.
1110
Serial Input 6.
1111
Serial Input 7.
SERIAL DATA OUTPUT 6/SERIAL DATA OUTPUT 7 INPUT SELECT REGISTER
Address: 0x16, Reset: 0x76, Name: SOUT_SOURCE_6_7
Rev. 0 | Page 51 of 92
Reset
Access
0x4
R/W
ADAU1372
Data Sheet
Table 35. Bit Descriptions for SOUT_SOURCE_6_7
Bits
Bit Name
[7:4]
SOUT_SOURCE7
[3:0]
Settings
Description
Reset
Access
Serial Data Output Channel 7 source select.
0x7
R/W
0x6
R/W
0000
Reserved.
0001
Reserved.
0010
Reserved.
0011
Reserved.
0100
Output ASRC Channel 0.
0101
Output ASRC Channel 1.
0110
Output ASRC Channel 2.
0111
Output ASRC Channel 3.
1000
Serial Input 0.
1001
Serial Input 1.
1010
Serial Input 2.
1011
Serial Input 3.
1100
Serial Input 4.
1101
Serial Input 5.
1110
Serial Input 6.
1111
Serial Input 7.
SOUT_SOURCE6
Serial Data Output Channel 6 source select.
0000
Reserved.
0001
Reserved.
0010
Reserved.
0011
Reserved.
0100
Output ASRC Channel 0.
0101
Output ASRC Channel 1.
0110
Output ASRC Channel 2.
0111
Output ASRC Channel 3.
1000
Serial Input 0.
1001
Serial Input 1.
1010
Serial Input 2.
1011
Serial Input 3.
1100
Serial Input 4.
1101
Serial Input 5.
1110
Serial Input 6.
1111
Serial Input 7.
Rev. 0 | Page 52 of 92
Data Sheet
ADAU1372
ADC_SDATA0/ADC_SDATA1 CHANNEL SELECT REGISTER
Address: 0x17, Reset: 0x04, Name: ADC_SDATA_CH
Table 36. Bit Descriptions for ADC_SDATA_CH
Bits
Bit Name
[7:4]
[3:2]
[1:0]
Settings
Description
Reset
Access
RESERVED
Reserved.
0x0
R/W
ADC_SDATA1_ST
SDATA1 output channel output select. Selects the output channel at which
ADC_SDATA1 starts to output data. The output port sequentially outputs data
following this start channel according to the setting of Bit SAI.
0x1
R/W
0x0
R/W
Description
Reset
Access
Output ASRC Channel 1 source select.
0x1
R/W
00
Channel 0.
01
Channel 2.
10
Channel 4.
11
Channel 6.
ADC_SDATA0_ST
SDATA0 output channel output select. Selects the output channel at which
ADC_SDATA0 starts to output data. The output port sequentially outputs data
following this start channel according to the setting of Bit SAI.
00
Channel 0.
01
Channel 2.
10
Channel 4.
11
Channel 6.
OUTPUT ASRC0/OUTPUT ASRC1 SOURCE REGISTER
Address: 0x18, Reset: 0x10, Name: ASRCO_SOURCE_0_1
Table 37. Bit Descriptions for ASRCO_SOURCE_0_1
Bits
Bit Name
[7:4]
ASRC_OUT_SOURCE1
Settings
0000
Reserved.
0001
Reserved.
0010
Reserved.
0011
Reserved.
0100
ADC0.
0101
ADC1.
0110
ADC2.
0111
ADC3.
Rev. 0 | Page 53 of 92
ADAU1372
Bits
[3:0]
Bit Name
Data Sheet
Settings
Description
Reset
Access
0x0
R/W
Description
Reset
Access
Output ASRC Channel 3 source select.
0x3
R/W
1000
Serial Input 0.
1001
Serial Input 1.
1010
Serial Input 2.
1011
Serial Input 3.
1100
Serial Input 4.
1101
Serial Input 5.
1110
Serial Input 6.
1111
Serial Input 7.
ASRC_OUT_SOURCE0
Output ASRC Channel 0 source select.
0000
Reserved.
0001
Reserved.
0010
Reserved.
0011
Reserved.
0100
ADC0.
0101
ADC1.
0110
ADC2.
0111
ADC3.
1000
Serial Input 0.
1001
Serial Input 1.
1010
Serial Input 2.
1011
Serial Input 3.
1100
Serial Input 4.
1101
Serial Input 5.
1110
Serial Input 6.
1111
Serial Input 7.
OUTPUT ASRC2/OUTPUT ASRC3 SOURCE REGISTER
Address: 0x19, Reset: 0x32, Name: ASRCO_SOURCE_2_3
Table 38. Bit Descriptions for ASRCO_SOURCE_2_3
Bits
Bit Name
[7:4]
ASRC_OUT_SOURCE3
Settings
0000
Reserved.
0001
Reserved.
0010
Reserved.
0011
Reserved.
0100
ADC0.
Rev. 0 | Page 54 of 92
Data Sheet
Bits
[3:0]
Bit Name
ADAU1372
Settings
Description
0101
ADC1.
0110
ADC2.
0111
ADC3.
1000
Serial Input 0.
1001
Serial Input 1.
1010
Serial Input 2.
1011
Serial Input 3.
1100
Serial Input 4.
1101
Serial Input 5.
1110
Serial Input 6.
1111
Serial Input 7.
ASRC_OUT_SOURCE2
Output ASRC Channel 2 source select.
0000
Reserved.
0001
Reserved.
0010
Reserved.
0011
Reserved.
0100
ADC0.
0101
ADC1.
0110
ADC2.
0111
ADC3.
1000
Serial Input 0.
1001
Serial Input 1.
1010
Serial Input 2.
1011
Serial Input 3.
1100
Serial Input 4.
1101
Serial Input 5.
1110
Serial Input 6.
1111
Serial Input 7.
Rev. 0 | Page 55 of 92
Reset
Access
0x2
R/W
ADAU1372
Data Sheet
INPUT ASRC CHANNEL SELECT REGISTER
Address: 0x1A, Reset: 0x00, Name: ASRC_MODE
Table 39. Bit Descriptions for ASRC_MODE
Bits
Bit Name
[7:4]
[3:2]
1
0
Settings
Description
Reset
Access
RESERVED
Reserved.
0x0
R/W
ASRC_IN_CH
Input ASRC channel select.
0x0
R/W
0x0
R/W
0x0
R/W
00
Serial Input Port Channel 0/Serial Input Port Channel 1.
01
Serial Input Port Channel 2/Serial Input Port Channel 3.
10
Serial Input Port Channel 4/Serial Input Port Channel 5.
11
Serial Input Port Channel 6/Serial Input Port Channel 7.
ASRC_OUT_EN
Output ASRC enable.
0
Disabled.
1
Enabled.
ASRC_IN_EN
Input ASRC enable.
0
Disabled.
1
Enabled.
ADC CONTROL 0 REGISTER
Address: 0x1B, Reset: 0x19, Name: ADC_CONTROL0
Table 40. Bit Descriptions for ADC_CONTROL0
Bits
Bit Name
[7:6]
Settings
Description
Reset
Access
RESERVED
Reserved.
0x0
R/W
5
RESERVED
Reserved.
0x0
R/W
4
ADC1_MUTE
Mute ADC1. Muting is accomplished by setting the volume control to maximum
attenuation. This bit has no effect if volume control is bypassed.
0x1
R/W
0
Unmuted.
1
Muted.
Rev. 0 | Page 56 of 92
Data Sheet
Bits
Bit Name
3
ADC0_MUTE
2
RESERVED
[1:0]
ADC_0_1_FS
ADAU1372
Settings
Description
Reset
Access
Mute ADC0. Muting is accomplished by setting the volume control to maximum
attenuation. This bit has no effect if volume control is bypassed.
0x1
R/W
Reserved.
0x0
R/W
Sets ADC sample rate.
0x1
R/W
Description
Reset
Access
0
Unmuted.
1
Muted.
00
96 kHz.
01
192 kHz.
10
Reserved.
11
Reserved.
ADC CONTROL 1 REGISTER
Address: 0x1C, Reset: 0x19, Name: ADC_CONTROL1
Table 41. Bit Descriptions for ADC_CONTROL1
Bits
Bit Name
Settings
[7:6]
RESERVED
Reserved.
0x0
R/W
5
RESERVED
Reserved.
0x0
R/W
4
ADC3_MUTE
Mute ADC3. Muting is accomplished by setting the volume control to maximum
attenuation. This bit has no effect if volume control is bypassed.
0x1
R/W
0x1
R/W
0
1
3
ADC2_MUTE
Unmuted.
Muted.
Mute ADC2. Muting is accomplished by setting the volume control to maximum
attenuation. This bit has no effect if volume control is bypassed.
0
Unmuted.
1
Muted.
2
RESERVED
Reserved.
0x0
R/W
[1:0]
ADC_2_3_FS
Sets ADC sample rate.
0x1
R/W
00
96 kHz.
01
192 kHz.
10
Reserved.
11
Reserved.
Rev. 0 | Page 57 of 92
ADAU1372
Data Sheet
ADC CONTROL 2 REGISTER
Address: 0x1D, Reset: 0x00, Name: ADC_CONTROL2
Table 42. Bit Descriptions for ADC_CONTROL2
Bits
Bit Name
Description
Reset
Access
7
RESERVED
Reserved.
0x0
R/W
[6:5]
HP_0_1_EN
High-pass filter settings.
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
4
3
2
1
0
Settings
00
Off.
01
1 Hz.
10
4 Hz.
11
8 Hz.
DMIC_POL0
Selects microphone polarity.
0
0 positive, 1 negative.
1
1 positive, 0 negative.
DMIC_SW0
Digital microphone swap.
0
Channel swap off (left channel on rising edge, right channel on falling edge)
1
Swap left and right.
DCM_0_1
Sets the input source to ADCs or digital microphones.
0
Decimator source set to ADC.
1
Decimator source set to digital microphones.
ADC_1_EN
Enable ADC1. This bit must be set in conjunction with the SYNC_1_EN bit in the
DECIM_PWR_MODES register to fully enable or disable the ADC
0
Disable.
1
Enable.
ADC_0_EN
Enable ADC0. This bit must be set in conjunction with the SYNC_0_EN bit in the
DECIM_PWR_MODES register to fully enable or disable the ADC
0
Disable.
1
Enable.
Rev. 0 | Page 58 of 92
Data Sheet
ADAU1372
ADC CONTROL 3 REGISTER
Address: 0x1E, Reset: 0x00, Name: ADC_CONTROL3
Table 43. Bit Descriptions for ADC_CONTROL3
Bits
Bit Name
Description
Reset
Access
7
RESERVED
Reserved.
0x0
R/W
[6:5]
HP_2_3_EN
High-pass filter settings.
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
4
3
2
1
0
Settings
00
Off.
01
1 Hz.
10
4 Hz.
11
8 Hz.
DMIC_POL1
Microphone polarity.
0
0 positive, 1 negative.
1
1 positive, 0 negative.
DMIC_SW1
Digital microphone swap.
0
Channel swap off (left channel on rising edge, right channel on falling edge)
1
Swap left and right.
DCM_2_3
Sets the input source to ADCs or digital microphones.
0
Decimator source set to ADC.
1
Decimator source set to digital microphone.
ADC_3_EN
Enable ADC3. This bit must be set in conjunction with the SYNC_3_EN bit in the
DECIM_PWR_MODES register to fully enable or disable the ADC.
0
Disable.
1
Enable.
ADC_2_EN
Enable ADC2. This bit must be set in conjunction with the SYNC_2_EN bit in the
DECIM_PWR_MODES register to fully enable or disable the ADC.
0
Disable.
1
Enable.
Rev. 0 | Page 59 of 92
ADAU1372
Data Sheet
ADC0 VOLUME CONTROL REGISTER
Address: 0x1F, Reset: 0x00, Name: ADC0_VOLUME
When SYNC_0_EN is set, the volume starts to ramp from −95.625 dB to the value in this register. The volume ramp time is (number of
steps) × 16/fS, where there are 256 steps between 0 dB and −95.625 dB. For example, with fS = 192 kHz, the volume ramps from
−95.625 dB to 0 dB in 21 ms.
Table 44. Bit Descriptions for ADC0_VOLUME
Bits
Bit Name
[7:0]
ADC_0_VOL
Settings
Description
Reset
Access
ADC0 volume setting.
0x0
R/W
00000000
0 dB.
00000001
−0.375 dB.
11111111
−95.625 dB.
ADC1 VOLUME CONTROL REGISTER
Address: 0x20, Reset: 0x00, Name: ADC1_VOLUME
When SYNC_1_EN is set, the volume starts to ramp from −95.625 dB to the value in this register. The volume ramp time is (number of
steps) × 16/fS, where there are 256 steps between 0 dB and −95.625 dB. For example, with fS = 192 kHz, the volume ramps from
−95.625 dB to 0 dB in 21 ms.
Table 45. Bit Descriptions for ADC1_VOLUME
Bits
Bit Name
[7:0]
ADC_1_VOL
Settings
Description
Reset
Access
ADC1 volume setting.
0x0
R/W
00000000
0 dB.
00000001
−0.375 dB.
11111111
−95.625 dB.
Rev. 0 | Page 60 of 92
Data Sheet
ADAU1372
ADC2 VOLUME CONTROL REGISTER
Address: 0x21, Reset: 0x00, Name: ADC2_VOLUME
When SYNC_2_EN is set, the volume starts to ramp from −95.625 dB to the value in this register. The volume ramp time is (number of
steps) × 16/fS, where there are 256 steps between 0 dB and −95.625 dB. For example, with fS = 192 kHz, the volume ramps from
−95.625 dB to 0 dB in 21 ms.
Table 46. Bit Descriptions for ADC2_VOLUME
Bits
Bit Name
[7:0]
ADC_2_VOL
Settings
Description
Reset
Access
ADC2 volume setting.
0x0
R/W
00000000
0 dB.
00000001
−0.375 dB.
11111111
−95.625 dB.
ADC3 VOLUME CONTROL REGISTER
Address: 0x22, Reset: 0x00, Name: ADC3_VOLUME
When SYNC_3_EN is set, the volume starts to ramp from −95.625 dB to the value in this register. The volume ramp time is (number of
steps) × 16/fS, where there are 256 steps between 0 dB and −95.625 dB. For example, with fS = 192 kHz, the volume ramps from
−95.625 dB to 0 dB in 21 ms.
Table 47. Bit Descriptions for ADC3_VOLUME
Bits
Bit Name
[7:0]
ADC_3_VOL
Settings
Description
Reset
Access
ADC3 volume setting.
0x0
R/W
00000000
0 dB.
00000001
−0.375 dB.
11111111
−95.625 dB.
Rev. 0 | Page 61 of 92
ADAU1372
Data Sheet
PGA CONTROL 0 REGISTER
Address: 0x23, Reset: 0x40, Name: PGA_CONTROL_0
This register controls the PGA connected to AIN0.
Table 48. Bit Descriptions for PGA_CONTROL_0
Bits
Bit Name
7
PGA_EN0
6
[5:0]
Settings
Description
Reset
Access
Select line or microphone input. Note that the PGA inverts the signal going
through it.
0x0
R/W
0x1
R/W
0x0
R/W
Description
Reset
Access
Select line or microphone input. Note that the PGA inverts the signal going
through it.
0x0
R/W
0
AIN0 used as a single-ended line input. PGA powered down.
1
AIN0 used as a single-ended microphone input. PGA powered up with slewing.
PGA_MUTE0
Enable PGA mute. When PGA is muted, PGA_GAIN0 is ignored.
0
Unmuted.
1
Muted.
000000
−12 dB.
000001
−11.25 dB.
010000
0 dB.
111110
+34.5 dB.
111111
+35.25 dB.
PGA_GAIN0
Set the gain of PGA0.
PGA CONTROL 1 REGISTER
Address: 0x24, Reset: 0x40, Name: PGA_CONTROL_1
This register controls the PGA connected to AIN1.
Table 49. Bit Descriptions for PGA_CONTROL_1
Bits
Bit Name
7
PGA_EN1
Settings
0
AIN1 used as a single-ended line input. PGA powered down.
1
AIN1 used as a single-ended microphone input. PGA powered up with slewing.
Rev. 0 | Page 62 of 92
Data Sheet
Bits
Bit Name
6
PGA_MUTE1
[5:0]
ADAU1372
Settings
Description
Reset
Access
Enable PGA1 mute. When PGA is muted, PGA_GAIN1 is ignored.
0x1
R/W
0x0
R/W
Description
Reset
Access
Select line or microphone input. Note that the PGA inverts the signal going
through it.
0x0
R/W
0x1
R/W
0x0
R/W
0
Unmuted.
1
Muted.
PGA_GAIN1
Set the gain of PGA1.
000000
−12 dB.
000001
−11.25 dB.
010000
0 dB.
111110
+34.5 dB.
111111
+35.25 dB.
PGA CONTROL 2 REGISTER
Address: 0x25, Reset: 0x40, Name: PGA_CONTROL_2
This register controls the PGA connected to AIN2.
Table 50. Bit Descriptions for PGA_CONTROL_2
Bits
Bit Name
7
PGA_EN2
Settings
0
1
6
[5:0]
PGA_MUTE2
AIN2 used as a single-ended line input. PGA powered down.
AIN2 used as a single-ended microphone input. PGA powered up with slewing.
Enable PGA2 mute. When PGA is muted, PGA_GAIN2 is ignored.
0
Unmuted.
1
Muted.
PGA_GAIN2
Set the gain of PGA2.
000000
−12 dB.
000001
−11.25 dB.
010000
0 dB.
111110
+34.5 dB.
111111
+35.25 dB.
Rev. 0 | Page 63 of 92
ADAU1372
Data Sheet
PGA CONTROL 3 REGISTER
Address: 0x26, Reset: 0x40, Name: PGA_CONTROL_3
This register controls the PGA connected to AIN3.
Table 51. Bit Descriptions for PGA_CONTROL_3
Bits
Bit Name
7
PGA_EN3
6
[5:0]
Settings
Description
Reset
Access
Select line or microphone input. Note that the PGA inverts the signal going
through it.
0x0
R/W
0x1
R/W
0x0
R/W
0
AIN3 used as a single-ended line input. PGA powered down.
1
AIN3 used as a single-ended microphone input. PGA powered up with slewing.
PGA_MUTE3
Enable PGA3 mute. When PGA is muted, PGA_GAIN3 is ignored.
0
Unmuted.
1
Muted.
000000
−12 dB.
000001
−11.25 dB.
010000
0 dB.
111110
+34.5 dB.
111111
+35.25 dB.
PGA_GAIN3
Set the gain of PGA3.
PGA SLEW CONTROL REGISTER
Address: 0x27, Reset: 0x00, Name: PGA_STEP_CONTROL
If PGA slew is disabled with the SLEW_PDx controls, the SLEW_RATE parameter is ignored for that PGA block.
Table 52. Bit Descriptions for PGA_STEP_CONTROL
Bits
Bit Name
Description
Reset
Access
[7:6]
RESERVED
Settings
Reserved.
0x0
R/W
[5:4]
SLEW_RATE
Controls how fast the PGA is slewed when changing gain.
0x0
R/W
00
21.5 ms.
01
42.5 ms.
10
85 ms.
Rev. 0 | Page 64 of 92
Data Sheet
Bits
Bit Name
3
SLEW_PD3
2
1
0
ADAU1372
Settings
Description
Reset
Access
PGA3 slew disable.
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
Description
Reset
Access
Reserved.
0x0
R/W
Boost control for PGA3.
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
0
PGA slew enabled.
1
PGA slew disabled.
SLEW_PD2
PGA2 slew disable.
0
PGA slew enabled.
1
PGA slew disabled.
0
PGA slew enabled.
1
PGA slew disabled.
SLEW_PD1
PGA1 slew disable.
SLEW_PD0
PGA0 slew disable.
0
PGA slew enabled.
1
PGA slew disabled.
PGA 10 dB GAIN BOOST REGISTER
Address: 0x28, Reset: 0x00, Name: PGA_10DB_BOOST
Each PGA can have an additional 10 dB gain added, making the PGA gain range −2 dB to +46 dB.
Table 53. Bit Descriptions for PGA_10DB_BOOST
Bits
Bit Name
[7:4]
RESERVED
3
PGA_3_BOOST
2
Settings
0
Default PGA gain set in Register PGA_CONTROL_3.
1
Additional 10 dB gain above setting in Register PGA_CONTROL_3.
PGA_2_BOOST
Boost control for PGA2.
0
1
1
0
PGA_1_BOOST
Default PGA gain set in Register PGA_CONTROL_2.
Additional 10 dB gain above setting in Register PGA_CONTROL_2.
Boost control for PGA1.
0
Default PGA gain set in Register PGA_CONTROL_1.
1
Additional 10 dB gain above setting in Register PGA_CONTROL_1.
PGA_0_BOOST
Boost control for PGA0.
0
Default PGA gain set in Register PGA_CONTROL_0.
1
Additional 10 dB gain above setting in Register PGA_CONTROL_0.
Rev. 0 | Page 65 of 92
ADAU1372
Data Sheet
INPUT AND OUTPUT CAPACITOR CHARGING REGISTER
Address: 0x29, Reset: 0x3F, Name: POP_SUPPRESS
Table 54. Bit Descriptions for POP_SUPPRESS
Bits
Bit Name
[7:6]
RESERVED
5
HP_POP_DIS1
4
Settings
1
0
Access
Reserved.
0x0
R/W
Disable pop suppression on Headphone Output 1.
0x1
R/W
0x1
R/W
0x1
R/W
0x1
R/W
0x1
R/W
0x1
R/W
Enabled.
1
Disabled.
HP_POP_DIS0
Disable pop suppression on Headphone Output 0.
1
2
Reset
0
0
3
Description
PGA_POP_DIS3
Enabled.
Disabled.
Disable pop suppression on PGA3 input.
0
Enabled.
1
Disabled.
PGA_POP_DIS2
Disable pop suppression on PGA2 input.
0
Enabled.
1
Disabled.
PGA_POP_DIS1
Disable pop suppression on PGA1 input.
0
Enabled.
1
Disabled.
PGA_POP_DIS0
Disable pop suppression on PGA0 input.
0
Enabled.
1
Disabled.
Rev. 0 | Page 66 of 92
Data Sheet
ADAU1372
ADC TO DAC TALKTHROUGH BYPASS PATH REGISTER
Address: 0x2A, Reset: 0x00, Name: TALKTHROUGH
Table 55. Bit Descriptions for TALKTHROUGH
Bits
Bit Name
[7:2]
[1:0]
Settings
Description
Reset
Access
RESERVED
Reserved.
0x0
R/W
TALKTHROUGH_PATH
Signal path when ADC to DAC Talkthrough bypass mode is enabled
0x0
R/W
Description
Reset
Access
Sets the DAC0 volume when talkthrough bypass mode is enabled.
0x0
R/W
Description
Reset
Access
Sets the DAC1 volume when talkthrough bypass mode is enabled.
0x0
R/W
00
No bypass, normal mode.
01
ADC0 to DAC0.
10
ADC1 to DAC1.
11
ADC0 and ADC1 to DAC0 and DAC1.
TALKTHROUGH BYPASS GAIN FOR ADC0 REGISTER
Address: 0x2B, Reset: 0x00, Name: TALKTHROUGH_GAIN0
Table 56. Bit Descriptions for TALKTHROUGH_GAIN0
Bits
Bit Name
[7:0]
TALKTHROUGH_GAIN0_VAL
Settings
TALKTHROUGH BYPASS GAIN FOR ADC1 REGISTER
Address: 0x2C, Reset: 0x00, Name: TALKTHROUGH_GAIN1
Table 57. Bit Descriptions for TALKTHROUGH_GAIN1
Bits
Bit Name
[7:0]
TALKTHROUGH_GAIN1_VAL
Settings
Rev. 0 | Page 67 of 92
ADAU1372
Data Sheet
MICBIAS CONTROL REGISTER
Address: 0x2D, Reset: 0x00, Name: MIC_BIAS
Table 58. Bit Descriptions for MIC_BIAS
Bits
Bit Name
[7:6]
5
4
Settings
Description
Reset
Access
RESERVED
Reserved.
0x0
R/W
MIC_EN1
MICBIAS1 output enable.
0x0
R/W
0x0
R/W
0
Disabled.
1
Enabled.
MIC_EN0
MICBIAS0 output enable.
0
Disabled.
1
Enabled.
3
RESERVED
Reserved.
0x0
R/W
2
RESERVED
Reserved.
0x0
R/W
1
MIC_GAIN1
Level of the MICBIAS1 output.
0x0
R/W
0x0
R/W
0
0
0.9 × AVDD.
1
0.65 × AVDD.
MIC_GAIN0
Level of the MICBIAS0 output.
0
0.9 × AVDD.
1
0.65 × AVDD.
Rev. 0 | Page 68 of 92
Data Sheet
ADAU1372
DAC CONTROL 1 REGISTER
Address: 0x2E, Reset: 0x18, Name: DAC_CONTROL1
Table 59. Bit Descriptions for DAC_CONTROL1
Bits
Bit Name
Description
Reset
Access
[7:6]
RESERVED
Reserved.
0x0
R/W
5
DAC_POL
Invert input polarity.
0x0
R/W
0x1
R/W
0x1
R/W
4
3
Settings
0
Normal.
1
Inverted.
DAC1_MUTE
Mute DAC1.
0
Unmuted.
1
Muted.
DAC0_MUTE
Mute DAC0.
0
Unmuted.
1
Muted.
2
RESERVED
Reserved.
0x0
R/W
1
DAC1_EN
Enable DAC1.
0x0
R/W
0x0
R/W
Description
Reset
Access
DAC0 volume setting.
0x0
R/W
0
0
Disable DAC1.
1
Enable DAC1.
DAC0_EN
Enable DAC0.
0
Disable DAC0.
1
Enable DAC0.
DAC0 VOLUME CONTROL REGISTER
Address: 0x2F, Reset: 0x00, Name: DAC0_VOLUME
Table 60. Bit Descriptions for DAC0_VOLUME
Bits
Bit Name
[7:0]
DAC_0_VOL
Settings
00000000
0 dB.
00000001
−0.375 dB.
11111111
−95.625 dB.
Rev. 0 | Page 69 of 92
ADAU1372
Data Sheet
DAC1 VOLUME CONTROL REGISTER
Address: 0x30, Reset: 0x00, Name: DAC1_VOLUME
Table 61. Bit Descriptions for DAC1_VOLUME
Bits
Bit Name
[7:0]
DAC_1_VOL
Settings
Description
Reset
Access
DAC1 volume setting.
0x0
R/W
00000000
0 dB.
00000001
−0.375 dB.
11111111
−95.625 dB.
HEADPHONE OUTPUT MUTES REGISTER
Address: 0x31, Reset: 0x0F, Name: OP_STAGE_MUTES
Table 62. Bit Descriptions for OP_STAGE_MUTES
Bits
Bit Name
[7:4]
[3:2]
[1:0]
Settings
Description
Reset
Access
RESERVED
Reserved.
0x0
R/W
HP_MUTE_R
Mute the right output pins. When a pin is muted, it can be used as a commonmode output.
0x3
R/W
0x3
R/W
00
Outputs unmuted.
01
HPOUTRP/LOUTRP muted, HPOUTRN/LOUTRN unmuted.
10
HPOUTRP/LOUTRP unmuted, HPOUTRN/LOUTRN muted.
11
Both output pins muted.
HP_MUTE_L
Mute the left output pins. When a pin is muted, it can be used as a common-mode
output.
00
Outputs unmuted.
01
HPOUTLP/LOUTLP muted, HPOUTLN/LOUTLN unmuted.
10
HPOUTLP/LOUTLP unmuted, HPOUTLN/LOUTLN muted.
11
Both output pins muted.
Rev. 0 | Page 70 of 92
Data Sheet
ADAU1372
SERIAL PORT CONTROL 0 REGISTER
Address: 0x32, Reset: 0x00, Name: SAI_0
Using 16-bit serial I/O limits device performance.
Table 63. Bit Descriptions for SAI_0
Bits
Bit Name
[7:6]
SDATA_FMT
[5:4]
[3:0]
Settings
Description
Reset
Access
Serial data format.
0x0
R/W
0x0
R/W
0x0
R/W
00
TDM, I S—data delayed from edge of LRCLK by 1 BCLK cycle.
01
TDM, left justified—data synchronized to edge of LRCLK.
10
Right justified, 24-bit data.
11
Right justified, 16-bit data.
SAI
2
Serial port mode.
00
Stereo (I S, left justified, right justified).
01
TDM2.
10
TDM4.
11
TDM8.
SER_PORT_FS
2
Sampling rate on the serial ports.
0000
48 kHz.
0001
8 kHz.
0010
12 kHz.
0011
16 kHz.
0100
24 kHz.
0101
32 kHz.
0110
96 kHz.
0111
192 kHz.
Rev. 0 | Page 71 of 92
ADAU1372
Data Sheet
SERIAL PORT CONTROL 1 REGISTER
Address: 0x33, Reset: 0x00, Name: SAI_1
Using 16-bit serial I/O limits device performance.
Table 64. Bit Descriptions for SAI_1
Bits
Bit Name
7
TDM_TS
6
Settings
3
2
1
0
Access
Select whether to tristate unused TDM channels or to actively drive these data
slots.
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
Unused outputs driven.
1
Unused outputs tristated.
BCLK_TDMC
Bit width in TDM mode.
1
4
Reset
0
0
5
Description
LR_MODE
24-bit data in each TDM channel.
16-bit data in each TDM channel.
Sets LRCLK mode.
0
50% duty cycle clock.
1
Pulse—LRCLK is a single BCLK cycle wide pulse.
LR_POL
Sets LRCLK polarity.
0
50%: when LRCLK goes low and then high, pulse mode is short positive pulse.
1
50%: when LRCLK goes high and then low, pulse mode is short negative pulse.
SAI_MSB
Sets data to be input/output either MSB or LSB first.
0
MSB first data.
1
LSB first data.
BCLKRATE
Sets the number of bit clock cycles per data channel.
0
32 BCLK cycles/channel.
1
16 BCLK cycles/channel.
BCLKEDGE
Sets the bit clock edge on which data changes.
0
Data changes on falling edge.
1
Data changes on rising edge.
SAI_MS
Sets the serial port into master or slave mode.
0
LRCLK/BCLK slave.
1
LRCLK/BCLK master.
Rev. 0 | Page 72 of 92
Data Sheet
ADAU1372
TDM OUTPUT CHANNEL DISABLE REGISTER
Address: 0x34, Reset: 0x00, Name: SOUT_CONTROL0
This register is for use only in TDM mode.
Table 65. Bit Descriptions for SOUT_CONTROL0
Bits
Bit Name
7
TDM7_DIS
6
5
4
Settings
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
Output channel disabled.
TDM6_DIS
Disable data in TDM Output Slot 6.
0
Output channel enabled.
1
Output channel disabled.
TDM5_DIS
Disable data in TDM Output Slot 5.
0
Output channel enabled.
1
Output channel disabled.
TDM4_DIS
Disable data in TDM Output Slot 4.
TDM3_DIS
Output channel enabled.
Output channel disabled.
Disable data in TDM Output Slot 3.
0
Output channel enabled.
1
Output channel disabled.
TDM2_DIS
Disable data in TDM Output Slot 2.
1
0
Disable data in TDM Output Slot 7.
1
0
1
Access
Output channel enabled.
1
2
Reset
0
0
3
Description
TDM1_DIS
Output channel enabled.
Output channel disabled.
Disable data in TDM Output Slot 1.
0
Output channel enabled.
1
Output channel disabled.
TDM0_DIS
Disable data in TDM Output Slot 0.
0
Output channel enabled.
1
Output channel disabled.
Rev. 0 | Page 73 of 92
ADAU1372
Data Sheet
MP0 FUNCTION SETTING REGISTER
Address: 0x38, Reset: 0x00, Name: MODE_MP0
Table 66. Bit Descriptions for MODE_MP0
Bits
Bit Name
Description
Reset
Access
[7:5]
RESERVED
Settings
Reserved.
0x0
R/W
[4:0]
MODE_MP0_VAL
Sets the function of Pin DAC_SDATA/MP0.
0x0
R/W
00000
Serial Input 0.
00001
Mute ADC0.
00010
Mute ADC1.
00011
Mute ADC2.
00100
Mute ADC3.
00101
Mute ADC0 and ADC1.
00110
Mute ADC2 and ADC3.
00111
Mute all ADCs.
01000
Mute DAC0.
01001
Mute DAC1.
01010
Mute both DACs.
01011
Reserved.
01100
Reserved.
01101
Reserved.
01110
Reserved.
01111
ADC to DAC bypass enable.
10000
Push-button volume up.
10001
Push-button volume down.
Rev. 0 | Page 74 of 92
Data Sheet
ADAU1372
MP1 FUNCTION SETTING REGISTER
Address: 0x39, Reset: 0x10, Name: MODE_MP1
Table 67. Bit Descriptions for MODE_MP1
Bits
Bit Name
Description
Reset
Access
[7:5]
RESERVED
Settings
Reserved.
0x0
R/W
[4:0]
MODE_MP1_VAL
Sets the function of Pin ADC_SDATA0/MP1
0x10
R/W
00000
Serial Output 0.
00001
Mute ADC0.
00010
Mute ADC1.
00011
Mute ADC2.
00100
Mute ADC3.
00101
Mute ADC0 and ADC1.
00110
Mute ADC2 and ADC3.
00111
Mute all ADCs.
01000
Mute DAC0.
01001
Mute DAC1.
01010
Mute both DACs.
01011
Reserved.
01100
Reserved.
01101
Reserved.
01110
Reserved.
01111
ADC to DAC bypass enable.
10000
Push-button volume up.
10001
Push-button volume down.
10010
Reserved.
Rev. 0 | Page 75 of 92
ADAU1372
Data Sheet
MP4 FUNCTION SETTING REGISTER
Address: 0x3C, Reset: 0x00, Name: MODE_MP4
Table 68. Bit Descriptions for MODE_MP4
Bits
Bit Name
[7:5]
[4:0]
Settings
Description
Reset
Access
RESERVED
Reserved.
0x0
R/W
MODE_MP4_VAL
Sets the function of Pin DMIC0_1/MP4
0x0
R/W
00000
Digital Microphone Input Channel 0/Digital Microphone Input Channel 1.
00001
Mute ADC0.
00010
Mute ADC1.
00011
Mute ADC2.
00100
Mute ADC3.
00101
Mute ADC0 and ADC1.
00110
Mute ADC2 and ADC3.
00111
Mute all ADCs.
01000
Mute DAC0.
01001
Mute DAC1.
01010
Mute both DACs.
01011
Reserved.
01100
Reserved.
01101
Reserved.
01110
Reserved.
01111
ADC to DAC bypass enable.
10000
Push-button volume up.
10001
Push-button volume down.
Rev. 0 | Page 76 of 92
Data Sheet
ADAU1372
MP5 FUNCTION SETTING REGISTER
Address: 0x3D, Reset: 0x00, Name: MODE_MP5
Table 69. Bit Descriptions for MODE_MP5
Bits
Bit Name
[7:5]
[4:0]
Settings
Description
Reset
Access
RESERVED
Reserved.
0x0
R/W
MODE_MP5_VAL
Sets the function of Pin DMIC2_3/MP5
0x0
R/W
00000
Digital Microphone Input Channel 2/Digital Microphone Input Channel 3.
00001
Mute ADC0.
00010
Mute ADC1.
00011
Mute ADC2.
00100
Mute ADC3.
00101
Mute ADC0 and ADC1.
00110
Mute ADC2 and ADC3.
00111
Mute all ADCs.
01000
Mute DAC0.
01001
Mute DAC1.
01010
Mute both DACs.
01011
Reserved.
01100
Reserved.
01101
Reserved.
01110
Reserved.
01111
ADC to DAC bypass enable.
10000
Push-button volume up.
10001
Push-button volume down.
Rev. 0 | Page 77 of 92
ADAU1372
Data Sheet
MP6 FUNCTION SETTING REGISTER
Address: 0x3E, Reset: 0x11, Name: MODE_MP6
Table 70. Bit Descriptions for MODE_MP6
Bits
Bit Name
Description
Reset
Access
[7:5]
RESERVED
Settings
Reserved.
0x0
R/W
[4:0]
MODE_MP6_VAL
Sets the function of Pin ADC_SDATA1/CLKOUT/MP6
0x11
R/W
00000
Serial Output 1.
00001
Mute ADC0.
00010
Mute ADC1.
00011
Mute ADC2.
00100
Mute ADC3.
00101
Mute ADC0 and ADC1.
00110
Mute ADC2 and ADC3.
00111
Mute all ADCs.
01000
Mute DAC0.
01001
Mute DAC1.
01010
Mute both DACs.
01011
Reserved.
01100
Reserved.
01101
Reserved.
01110
Reserved.
01111
ADC to DAC bypass enable.
10000
Push-button volume up.
10001
Push-button volume down.
10010
Clock output.
Rev. 0 | Page 78 of 92
Data Sheet
ADAU1372
PUSH-BUTTON VOLUME SETTINGS REGISTER
Address: 0x3F, Reset: 0x00, Name: PB_VOL_SET
This register must be written before the PB_VOL_CONV_VAL bits are set to something other than the default value. Otherwise, the
push-button volume control is initialized to −96 dB.
Table 71. Bit Descriptions for PB_VOL_SET
Bits
Bit Name
[7:3]
PB_VOL_INIT_VAL
[2:0]
Settings
Description
Reset
Access
Sets the initial volume of the push-button volume control. Each increment of
this register attenuates the level by 1.5 dB, from 0 dB to −46.5 dB.
0x0
R/W
0x0
R/W
00000
0.0 dB.
00001
−1.5 dB.
11111
−46.5 dB.
HOLD
Sets the length of time that the button is held before the volume ramp begins.
000
150 ms.
001
300 ms.
010
450 ms.
011
600 ms.
100
900 ms.
101
1200 ms.
Rev. 0 | Page 79 of 92
ADAU1372
Data Sheet
PUSH-BUTTON VOLUME CONTROL ASSIGNMENT REGISTER
Address: 0x40, Reset: 0x87, Name: PB_VOL_CONV
Table 72. Bit Descriptions for PB_VOL_CONV
Bits
Bit Name
[7:6]
GAINSTEP
[5:3]
[2:0]
Settings
Description
Reset
Access
Sets the gain step for each press of the volume control button.
0x2
R/W
0x0
R/W
0x7
R/W
00
0.375 dB/press.
01
1.5 dB/press.
10
3.0 dB/press.
11
4.5 dB/press.
RAMPSPEED
Sets the speed in dB/sec at which the volume control ramps when a button
is pressed.
000
60 dB/sec.
001
48 dB/sec.
010
36 dB/sec.
011
30 dB/sec.
100
24 dB/sec.
101
18 dB/sec.
110
12 dB/sec.
111
6 dB/sec.
PB_VOL_CONV_VAL
Converters controlled by push-button volume. The push-button volume
control is enabled when these bits are set to something other than the
default setting (111). When set to 111, the push-button volume is disabled
and the converter volumes are set by the ADCx_VOLUME and
DACx_VOLUME registers.
000
ADC0 and ADC1.
001
ADC2 and ADC3.
010
All ADCs.
011
DAC0 and DAC1.
100
DAC0.
101
DAC1.
110
Reserved.
111
None (default)
Rev. 0 | Page 80 of 92
Data Sheet
ADAU1372
DEBOUNCE MODES REGISTER
Address: 0x41, Reset: 0x05, Name: DEBOUNCE_MODE
Table 73. Bit Descriptions for DEBOUNCE_MODE
Bits
Bit Name
[7:3]
[2:0]
Settings
Description
Reset
Access
RESERVED
Reserved.
0x0
R/W
DEBOUNCE
The debounce time setting for the MPx inputs.
0x5
R/W
000
Debounce 300 µs.
001
Debounce 600 µs.
010
Debounce 900 µs.
011
Debounce 5 ms.
100
Debounce 10 ms.
101
Debounce 20 ms.
110
Debounce 40 ms.
111
No debounce.
HEADPHONE LINE OUTPUT SELECT REGISTER
Address: 0x43, Reset: 0x0F, Name: OP_STAGE_CTRL
Table 74. Bit Descriptions for OP_STAGE_CTRL
Bits
Bit Name
[7:6]
5
Settings
Description
Reset
Access
RESERVED
Reserved.
0x0
R/W
HP_EN_R
Sets the right channel in line output or headphone mode.
0x0
R/W
0
Right output in line output mode.
1
Right output in headphone mode.
Rev. 0 | Page 81 of 92
ADAU1372
Bits
Bit Name
4
HP_EN_L
[3:2]
[1:0]
Data Sheet
Settings
Description
Reset
Access
Sets the left channel in line output or headphone mode.
0x0
R/W
0x3
R/W
0x3
R/W
0
Left output in line output mode.
1
Left output in headphone output mode.
HP_PDN_R
Output stage power control. Powers down the right output stage, regardless of
whether the device is in line output or headphone mode. After enabling the
headphone output, wait at least 6 ms before unmuting the headphone output by
setting HP_MUTE_R in the OP_STAGE_MUTES register to 00.
00
HPOUTRN/LOUTRN and HPOUTRP/LOUTRP outputs enabled.
01
HPOUTRN/LOUTRN enabled, HPOUTRP/LOUTRP disabled.
10
HPOUTRN/LOUTRN disabled, HPOUTRP/LOUTRP enabled.
11
Right output stages powered down.
HP_PDN_L
Output stage power control. Powers down the left output stage, regardless of
whether the device is in line output or headphone mode. After enabling the
headphone output, wait at least 6 ms before unmuting the headphone output by
setting HP_MUTE_L in the OP_STAGE_MUTES register to 00.
00
HPOUTLN/LOUTLN and HPOUTLP/LOUTLP outputs enabled.
01
HPOUTLN/LOUTLN enabled, HPOUTLP/LOUTLP disabled.
10
HPOUTLN/LOUTLN disabled, HPOUTLP/LOUTLP enabled.
11
Left output stages powered down.
DECIMATOR POWER CONTROL REGISTER
Address: 0x44, Reset: 0x00, Name: DECIM_PWR_MODES
These bits enable clocks to the digital filters and ASRC decimator filters of the ADCs. These bits must be enabled for all channels that are
used in the design. To use the ADCs, these SYNC_x_EN bits must be enabled along with the appropriate ADC_x_EN bits in the
ADC_CONTROL2 and ADC_CONTROL3 registers. If the digital microphone inputs are used, the SYNC_x_EN bits can be set without
setting ADC_x_EN.
Table 75. Bit Descriptions for DECIM_PWR_MODES
Bits
Bit Name
7
DEC_3_EN
6
Settings
Description
Reset
Access
Control power to the ASRC3 decimator.
0x0
R/W
0x0
R/W
0
Powered down.
1
Powered up.
DEC_2_EN
Control power to the ASRC2 decimator.
0
Powered down.
1
Powered up.
Rev. 0 | Page 82 of 92
Data Sheet
Bits
Bit Name
5
DEC_1_EN
4
3
2
1
0
ADAU1372
Settings
Description
Reset
Access
Control power to the ASRC1 decimator.
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
Description
Reset
Access
0
Powered down.
1
Powered up.
DEC_0_EN
Control power to the ASRC0 decimator.
0
Powered down.
1
Powered up.
SYNC_3_EN
ADC3 filter power control.
0
Powered down.
1
Powered up.
SYNC_2_EN
ADC2 filter power control.
0
Powered down.
1
Powered up.
SYNC_1_EN
ADC1 filter power control.
0
Powered down.
1
Powered up.
SYNC_0_EN
ADC0 filter power control
0
Powered down.
1
Powered up.
ASRC INTERPOLATOR AND DAC MODULATOR POWER CONTROL REGISTER
Address: 0x45, Reset: 0x00, Name: INTERP_PWR_MODES
Table 76. Bit Descriptions for INTERP_PWR_MODES
Bits
Bit Name
[7:4]
RESERVED
Reserved.
0x0
R/W
3
MOD_1_EN
DAC Modulator 1 enable.
0x0
R/W
0x0
R/W
0x0
R/W
2
1
Settings
0
Powered down.
1
Powered up.
MOD_0_EN
DAC Modulator 0 enable.
0
Powered down.
1
Powered up.
INT_1_EN
ASRC Interpolator 1 enable.
0
Powered down.
1
Powered up.
Rev. 0 | Page 83 of 92
ADAU1372
Bits
Bit Name
0
INT_0_EN
Data Sheet
Settings
Description
Reset
Access
ASRC Interpolator 0 enable.
0x0
R/W
0
Powered down.
1
Powered up.
ANALOG BIAS CONTROL 0 REGISTER
Address: 0x46, Reset: 0x00, Name: BIAS_CONTROL0
Table 77. Bit Descriptions for BIAS_CONTROL0
Bits
Bit Name
[7:6]
HP_IBIAS
[5:4]
[3:2]
[1:0]
Settings
Description
Reset
Access
Headphone output bias current setting. Higher bias currents result in higher
performance.
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
00
Normal operation (default)
01
Extreme power saving.
10
Enhanced performance.
11
Power saving.
AFE_IBIAS01
Analog Front-End 0 and Analog Front-End 1 bias current setting. Higher bias
currents result in higher performance.
00
Normal operation (default)
01
Extreme power saving.
10
Enhanced performance.
11
Power saving.
ADC_IBIAS23
ADC2 and ADC3 bias current setting. Higher bias currents result in higher
performance.
00
Normal operation (default)
01
Reserved.
10
Enhanced performance.
11
Power saving.
ADC_IBIAS01
ADC0 and ADC1 bias current setting. Higher bias currents result in higher
performance.
00
Normal operation (default)
01
Reserved.
10
Enhanced performance.
11
Power saving.
Rev. 0 | Page 84 of 92
Data Sheet
ADAU1372
ANALOG BIAS CONTROL 1 REGISTER
Address: 0x47, Reset: 0x00, Name: BIAS_CONTROL1
Table 78. Bit Descriptions for BIAS_CONTROL1
Bits
Bit Name
7
RESERVED
6
CBIAS_DIS
[5:4]
[3:2]
Settings
Reset
Access
Reserved.
0x0
R/W
Central analog bias circuitry. Higher bias currents result in higher performance.
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
0
Powered up.
1
Powered down.
AFE_IBIAS23
Analog Front-End 2 and Analog Front-End 3 bias current setting. Higher bias
currents result in higher performance.
00
Normal operation (default).
01
Extreme power saving.
10
Enhanced performance.
11
Power saving.
MIC_IBIAS
Microphone input bias current setting. Higher bias currents result in higher
performance.
00
[1:0]
Description
Normal operation (default).
01
Extreme power saving.
10
Enhanced performance.
11
Power saving.
DAC_IBIAS
DAC bias current setting. Higher bias currents result in higher performance.
00
Normal operation (default).
01
Power saving.
10
Superior performance.
11
Enhanced performance.
Rev. 0 | Page 85 of 92
ADAU1372
Data Sheet
DIGITAL PIN PULL-UP CONTROL 0 REGISTER
Address: 0x48, Reset: 0x7F, Name: PAD_CONTROL0
This register enables or disables pull-up resistors on the digital input pins.
Table 79. Bit Descriptions for PAD_CONTROL0
Bits
Bit Name
7
RESERVED
6
DMIC2_3_PU
5
Settings
2
1
0
Access
Reserved.
0x0
R/W
Digital Microphone 2 and Microphone 3 Pull-up.
0x1
R/W
0x1
R/W
0x1
R/W
0x1
R/W
0x1
R/W
0x1
R/W
0x1
R/W
Pull-up enabled.
1
Pull-up disabled.
DMIC0_1_PU
Digital Microphone 0 and Microphone 1 Pull-up.
1
3
Reset
0
0
4
Description
LRCLK_PU
Pull-up enabled.
Pull-up disabled.
Left/Right Clock Pull-up.
0
Pull-up enabled.
1
Pull-up disabled.
BCLK_PU
Bit Clock Pull-up.
0
Pull-up enabled.
1
Pull-up disabled.
ADC_SDATA1_PU
ADC Serial Data 1 Pull-up.
0
Pull-up enabled.
1
Pull-up disabled.
ADC_SDATA0_PU
ADC Serial Data 0 Pull-up.
0
Pull-up enabled.
1
Pull-up disabled.
DAC_SDATA_PU
DAC Serial Data Pull-up.
0
Pull-up enabled.
1
Pull-up disabled.
Rev. 0 | Page 86 of 92
Data Sheet
ADAU1372
DIGITAL PIN PULL-UP CONTROL 1 REGISTER
Address: 0x49, Reset: 0x1F, Name: PAD_CONTROL1
This register enables or disables pull-up resistors on the digital input pins.
Table 80. Bit Descriptions for PAD_CONTROL1
Bits
Bit Name
[7:5]
Description
Reset
Access
RESERVED
Reserved.
0x0
R/W
4
RESERVED
Reserved.
0x1
R/W
3
SCL_PU
Serial Clock Pull-up.
0x1
R/W
0x1
R/W
0x1
R/W
0x1
R/W
2
1
0
Settings
0
Pull-up enabled.
1
Pull-up disabled.
SDA_PU
Serial Data Pull-up.
0
Pull-up enabled.
1
Pull-up disabled.
ADDR1_PU
Address 1 Pull-up.
0
Pull-up enabled.
1
Pull-up disabled.
ADDR0_PU
Address 0 Pull-up.
0
Pull-up enabled.
1
Pull-up disabled.
Rev. 0 | Page 87 of 92
ADAU1372
Data Sheet
DIGITAL PIN PULL-DOWN CONTROL 2 REGISTER
Address: 0x4A, Reset: 0x00, Name: PAD_CONTROL2
This register enables or disables pull-down resistors on the digital input pins.
Table 81. Bit Descriptions for PAD_CONTROL2
Bits
Bit Name
7
RESERVED
6
DMIC2_3_PD
5
Settings
2
1
0
Access
Reserved.
0x0
R/W
Digital Microphone 2 and Microphone 3 Pull-down.
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
Pull-down disabled.
1
Pull-down enabled.
DMIC0_1_PD
Digital Microphone 0 and Microphone 1 Pull-down.
1
3
Reset
0
0
4
Description
LRCLK_PD
Pull-down disabled.
Pull-down enabled.
Left/Right Clock Pull-down.
0
Pull-down disabled.
1
Pull-down enabled.
BCLK_PD
Bit Clock Pull-down.
0
Pull-down disabled.
1
Pull-down enabled.
ADC_SDATA1_PD
ADC Serial Data 1 Pull-down.
0
Pull-down disabled.
1
Pull-down enabled.
ADC_SDATA0_PD
ADC Serial Data 0 Pull-down.
0
Pull-down disabled.
1
Pull-down enabled.
DAC_SDATA_PD
DAC Serial Data Pull-down.
0
Pull-down disabled.
1
Pull-down enabled.
Rev. 0 | Page 88 of 92
Data Sheet
ADAU1372
DIGITAL PIN PULL-DOWN CONTROL 3 REGISTER
Address: 0x4B, Reset: 0x00, Name: PAD_CONTROL3
This register enables or disables pull-down resistors on the digital input pins.
Table 82. Bit Descriptions for PAD_CONTROL3
Bits
Bit Name
[7:5]
Description
Reset
Access
RESERVED
Reserved.
0x0
R/W
4
RESERVED
Reserved.
0x0
R/W
3
SCL_PD
Pull-down enable.
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
2
1
0
Settings
0
Pull-down disabled.
1
Pull-down enabled.
SDA_PD
Pull-down enable.
0
Pull-down disabled.
1
Pull-down enabled.
ADDR1_PD
Pull-down enable.
0
Pull-down disabled.
1
Pull-down enabled.
ADDR0_PD
Pull-down enable.
0
Pull-down disabled.
1
Pull-down enabled.
Rev. 0 | Page 89 of 92
ADAU1372
Data Sheet
DIGITAL PIN DRIVE STRENGTH CONTROL 4 REGISTER
Address: 0x4C, Reset: 0x00, Name: PAD_CONTROL4
Table 83. Bit Descriptions for PAD_CONTROL4
Bits
Bit Name
Description
Reset
Access
7
RESERVED
Reserved.
0x0
R/W
6
RESERVED
Reserved.
0x0
R/W
5
RESERVED
Reserved.
0x0
R/W
4
LRCLK_DRV
Drive strength control.
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
0x0
R/W
3
2
1
0
Settings
0
Low drive strength.
1
High drive strength.
BCLK_DRV
Drive strength control.
0
Low drive strength.
1
High drive strength.
ADC_SDATA1_DRV
Drive strength control.
0
Low drive strength.
1
High drive strength.
ADC_SDATA0_DRV
RESERVED
Drive strength control.
0
Low drive strength.
1
High drive strength.
Reserved.
Rev. 0 | Page 90 of 92
Data Sheet
ADAU1372
DIGITAL PIN DRIVE STRENGTH CONTROL 5 REGISTER
Address: 0x4D, Reset: 0x00, Name: PAD_CONTROL5
Table 84. Bit Descriptions for PAD_CONTROL5
Bits
Bit Name
[7:5]
Description
Reset
Access
RESERVED
Reserved.
0x0
R/W
4
RESERVED
Reserved.
0x0
R/W
3
SCL_DRV
Drive strength control.
0x0
R/W
0x0
R/W
2
Settings
0
Low drive strength.
1
High drive strength.
SDA_DRV
Drive strength control.
0
Low drive strength.
1
High drive strength.
1
RESERVED
Reserved.
0x0
R/W
0
RESERVED
Reserved.
0x0
R/W
Rev. 0 | Page 91 of 92
ADAU1372
Data Sheet
OUTLINE DIMENSIONS
6.10
6.00 SQ
5.90
31
40
30
0.50
BSC
1
TOP VIEW
0.80
0.75
0.70
PKG-003438
10
11
20
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
SEATING
PLANE
4.45
4.30 SQ
4.25
EXPOSED
PAD
21
0.45
0.40
0.35
PIN 1
INDICATOR
BOTTOM VIEW
0.25 MIN
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-220-WJJD.
05-06-2011-A
PIN 1
INDICATOR
0.30
0.23
0.18
Figure 77. 40-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
6 mm × 6 mm Body, Very Very Thin Quad
(CP-40-10)
Dimension shown in millimeters
ORDERING GUIDE
Model 1
ADAU1372BCPZ
ADAU1372BCPZRL
EVAL-ADAU1372Z
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
Package Description
40-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
40-Lead Lead Frame Chip Scale Package [LFCSP_WQ], 13" Tape and Reel
Evaluation Board
Z = RoHS Compliant Part.
©2014 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D12702-0-12/14(0)
Rev. 0 | Page 92 of 92
Package Option
CP-40-10
CP-40-10
Similar pages