Anaren BD2327N50100AHF Ultra low profile 0404 balun Datasheet

Model BD2327N50100AHF
Rev D
Ultra Low Profile 0404 Balun
50Ω to 100Ω Balanced
Description
The BD2327N50100AHF is a low cost, low profile sub-miniature unbalanced
to balanced transformer designed for differential inputs and output locations on
modern chipsets in an easy to use surface mount package. The
BD2327N50100AHF is ideal for high volume manufacturing and delivers higher
performance than traditional ceramic baluns. The BD2327N50100AHF has an
unbalanced port impedance of 50Ω and a 100Ω balanced port impedance. This
transformation enables single ended signals to be applied to differential ports on
modern integrated chipsets. The output ports have equal amplitude (-3dB) with 180
degree phase differential. The BD2327N50100AHF is available on tape and reel for
pick and place high volume manufacturing.
Detailed Electrical Specifications: Specifications subject to change without notice.
Features:
•
•
•
•
•
•
•
•
•
•
•
•
•
2300 – 2700 MHz
0.5 mm Height Profile
50 Ohm to 2 x 50 Ohm
Low Insertion Loss
WiMax
802.11 b+g
MIMO b+g
Bluetooth
Zigbee
Surface Mountable
Tape & Reel
RoHS Compliant
Halogen Free
ROOM (25°°C)
Parameter
Min.
Frequency
Unbalanced Port Impedance
Balanced Port Impedance
Return Loss
Insertion Loss*
Amplitude Balance
Phase Balance
CMRR
Power Handling @85C
Power Handling @105C
Operating Temperature
2300
Typ.
50
100
24
0.6
0.4
1
32
17
Max
Unit
2700
MHz
Ω
Ω
dB
dB
dB
Degrees
dB
Watts
Watts
ºC
0.8
1.0
7
1.0
0.6
+105
-55
* Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC)
Outline Drawing
Top View (Near-side)
Side View
Bottom View (Far-side)
.24
.51±.05
1.04±.10
3x .27
1
2
.24
3x .27
.30
.30
1.04±.10
.50
3x .25
3
4
3x .25
Pin Designation
GND / DC Feed
1
+ RF GND
Dimensions are in Millimeters
Mechanical Outline
2 Unbalanced Port
3 Balanced Port
4 Balanced Port
Visit us at
www.anaren.com
.50
Tolerances are Non-Cumulative
USA/Canada:
Toll Free:
Europe:
Asia:
(315) 432-8909
(800) 411-6596
+44 2392-232392
+86 512-62749282
Model BD2327N50100AHF
Rev D
Typical Performance:2200 MHz. to 2800 MHz.
Insertion Loss
-3
-0.3
-6
-0.6
-9
-0.9
-12
-1.2
-15
-1.5
2800
2800
2550
2500
2450
2400
2350
2300
-20
2800
-2
2750
-15
2700
-1.5
2650
-10
2600
-1
2250
0
-5
2200
0
-0.5
2550
2750
5
2500
2750
0.5
2450
2700
10
2400
2700
1
2350
2650
15
deg
2
1.5
2300
2650
Phase Balance
20
2250
2600
Amplitude Balance
2200
2600
Frequency [MHz]
Frequency [MHz]
[dB]
2550
2200
2800
2750
2700
2650
2600
2550
2500
2450
2400
-3.6
2350
-36
2300
-3.3
2250
-3
-33
2500
-2.7
-30
2450
-2.4
-27
2400
-2.1
-24
2350
-1.8
-21
2300
-18
2250
[dB]
0
2200
[dB]
Return Loss - Input
0
Frequency [MHz]
Frequency [MHz]
CM RR
0
-3
-6
-9
-12
-18
-21
-24
-27
-30
-33
2800
2750
2700
2650
2600
2550
2500
2450
2400
2350
2300
2250
-36
2200
[dB]
-15
Frequency [MHz]
Visit us at
www.anaren.com
USA/Canada:
Toll Free:
Europe:
Asia:
(315) 432-8909
(800) 411-6596
+44 2392-232392
+86 512-62749282
Model BD2327N50100AHF
Rev D
Wide Band Performance: 500 MHz. to 8500 MHz.
Insertion Loss
-3
-0.3
-6
-0.6
-9
-0.9
-12
-1.2
-15
-1.5
7000
7500
8000
8500
8000
8500
5500
5500
5000
4500
4000
3500
3000
2500
2000
1500
8500
8000
7500
7000
-20
6500
-2
6000
-15
5500
-1.5
5000
-10
4500
-1
500
0
-5
1000
0
-0.5
4000
7500
5
3500
6500
0.5
3000
7000
10
2500
6500
1
2000
6000
15
deg
2
1.5
1500
5000
Phase Balance
20
1000
6000
Amplitude Balance
500
4500
Frequency [MHz]
Frequency [MHz]
[dB]
4000
500
8500
8000
7500
7000
6500
6000
5500
5000
4500
4000
3500
3000
2500
-3.6
2000
-36
1500
-3.3
1000
-3
-33
3500
-2.7
-30
3000
-2.4
-27
2500
-2.1
-24
2000
-1.8
-21
1500
-18
1000
[dB]
0
500
[dB]
Return Loss - Input
0
Frequency [MHz]
Frequency [MHz]
CMRR
0
-3
-6
-9
-12
-18
-21
-24
-27
-30
-33
8500
8000
7500
7000
6500
6000
5500
5000
4500
4000
3500
3000
2500
2000
1500
1000
-36
500
[dB]
-15
Frequency [MHz]
Visit us at
www.anaren.com
USA/Canada:
Toll Free:
Europe:
Asia:
(315) 432-8909
(800) 411-6596
+44 2392-232392
+86 512-62749282
Model BD2327N50100AHF
Rev D
Mounting Configuration:
In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be
used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet
published specifications.
All of the Xinger components are constructed from organic PTFE based composites which possess excellent
electrical and mechanical stability. Xinger components are compliant to a variety of ROHS and Green standards and
ready for Pb-free soldering processes. Pads are Gold plated with a Nickel barrier.
An example of the PCB footprint used in the testing of these parts is shown below. An example of a DC-biased
footprint is also shown below. In specific designs, the transmission line widths need to be adjusted to the unique
dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances.
With No DC Bias
With DC Bias
Plated thru
hole to
ground
.33
3x Transmission
Line
Plated thru
hole to
ground
3x .29
3x Transmission
Line
3x .29
.33
3x .29
.33
3x .29
.22
.50
.22
.50
.22
.50
.22
.50
Circuit Pattern
Circuit Pattern
Footprint Pad (s)
Solder Resist
Footprint Pad (s)
Dimensions are in Millimeters
Mounting Footprint
Solder Resist
Visit us at
www.anaren.com
Dimensions are in Millimeters
Mounting Footprint
USA/Canada:
Toll Free:
Europe:
Asia:
(315) 432-8909
(800) 411-6596
+44 2392-232392
+86 512-62749282
Model BD2327N50100AHF
Rev D
Packaging and Ordering Information
Parts are available in reel and are packaged per EIA 481-D. Parts are oriented in tape and reel as shown below.
Minimum order quantities are 4000 per reel.
Visit us at
www.anaren.com
USA/Canada:
Toll Free:
Europe:
Asia:
(315) 432-8909
(800) 411-6596
+44 2392-232392
+86 512-62749282
Similar pages