TI1 BQ2016DBQG4 Gas gauge ic for high discharge rate Datasheet

bq2016
GAS GAUGE IC FOR
HIGH DISCHARGE RATES
SLUS475A – JANUARY 2001 – REVISED NOVEMBER 2002
D Provides Accurate Measurement of
D
D
D
D
D
D
D
TSSOP PACKAGE
(TOP VIEW)
Available Capacity in Nicd or NiMH
Batteries
Measures a Wide Dynamic-Current Range
Requires ≤ 1 Square Inch of PCB Space for
Easy Pack Integration
Measures Charge Flow Using a Low-Offset
V-to-F Converter
Automatically Compensates Measurements
for Rate and Temperature
Supports 5 LEDs for Remaining Capacity
Indication
Provides a 1-Wire HDQ Communication
Interface
Packaging: 28-Pin SSOP
HDQ
NC
NC
RBI
REG
NC
VCC
VSS
DISP
LED1
LED2
LED3
LED4
LED5
description
1
28
2
27
3
26
4
25
5
24
6
23
7
22
8
21
9
20
10
19
11
18
12
17
13
16
14
15
NC
NC
SB
PROG
VPFC
NC
SR1
SR2
SRC
TS
THON
CVON
NC
NC
NC — Do not connect
The bq2016 gas gauge IC for battery pack or in-system installation maintains an accurate record of available
battery capacity. To integrate charge and discharge activity of the battery, the IC monitors a voltage drop across
a sense resistor connected in series with the cells of the battery. The bq2016 compensates for battery
temperature, charge/discharge rate, and battery self-discharge to the charge counter to provide availablecapacity information across a wide range of operating conditions. The bq2016 works with NiCd or NiMH battery
packs that have a capacity of 1 to 4.5 Ah and that are designed for high discharge rate applications such as
power tools.
The VPFC input sets the initial full charge reference of the battery pack. The bq2016 learns the true discharge
capacity of the battery pack and automatically updates the full-charge reference during the course of a
discharge cycle from full to empty. The remaining capacity is reported as the ratio between the actual discharge
capacity and the full-charge capacity. The bq2016 communicates available capacity using 5 LEDs or the 1-wire
communications port.
The 1-wire serial communication port (5Kb/s) allows an external processor to read and write the internal
registers of the bq2016. Communication with the bq2016 is useful for pack testing or host processing of the
available battery information. The internal registers include available battery capacity, voltage, temperature,
current, and battery status. The RBI input maintains the register set in the event of pack voltage collapse due
to a high discharge pulse.
The bq2016 circuit can operate from the cells in the pack. The REG output and an external FET provide a simple,
inexpensive voltage regulator to supply power to the circuit from the cells
OPTIONS
TJ
28-PIN SSOP PACKAGE
–20°C to 70°C
bq2016DBQ
bq2016DBQR
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  2002, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
bq2016
GAS GAUGE IC FOR
HIGH DISCHARGE RATES
SLUS475A– JANUARY 2001 – REVISED NOVEMBER 2002
Terminal Functions
TERMINAL
NAME
NO.
I/O
DESCRIPTION
HDQ
1
I/O
RBI
4
I
Register backup input provides backup potential to the bq2016 registers during periods of low operating
voltage. RBI accepts a storage capacitor or a battery input.
REG
5
O
Regulator output provides a reference to control an n-JFET for VCC regulation to the bq2016 from the
battery potential.
VCC
VSS
7
I
Supply voltage input
LED1–LED5
8
Serial communication input/output. Open-drain bidirectional communications port.
Ground
10–14
O
LED display segment outputs that each may drive an external LED.
CVON
17
O
Cell voltage divider control. Output to connect the voltage divider on the voltage input during
measurement.
VPFC
24
I
Program capacity input. 16-level input to program the initial battery full-charge reference.
SB
26
I
Battery voltage input. Input connection to monitor battery–pack voltage.
21,22
I
Sense resistor inputs. Input connections for a small value sense resistor to monitor the battery charge and
discharge current flow.
SRC
20
I
Current sense voltage input to monitor instantaneous current.
DISP
9
I
Display activation input that activates the LED drivers LED1–LED5.
TS
19
I
Temperature sense input connects to an external thermistor or should be grounded when using the internal
thermistor. The function depends on the state of the PROG input.
PROG
25
I
Program input defines the temperature measurement thermistor (internal or external).
THON
18
O
Thermistor bias control output to control a switch in series with an optional external thermistor.
SR2–SR1
NC
2
2, 3, 6, 15,
16, 23, 27,
28
Do not connect. For proper device operation, these pins should not be connected.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
bq2016
GAS GAUGE IC FOR
HIGH DISCHARGE RATES
SLUS475A– JANUARY 2001 – REVISED NOVEMBER 2002
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Relative to VSS: VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 6 V
VIN (All other pins) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 6 V
Operating temperature, TOPR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –20°C to 70°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
dc electrical characteristics
PARAMETER
VCC
ICC
Supply voltage
VOLS
VOLS
Sink voltage: LED1–LED5
VIL
VIH
Input voltage low DISP
VOL
VILS
Output voltage low HDQ
VIHS
VAI
Input voltage high HDQ
IRB
VRBI
RBI data-retention input current
ZAI1
ZAI2
Input impedance: SR1, SR2
Input impedance: SB, SRC
TEST CONDITIONS
MIN
TYP
2.7
Operating current
MAX
3.3
3.7
V
180
235
µA
0.4
V
IOLS = 5 mA
IOLS = 1 mA
Sink voltage: TI ION, CVON
0.36
V
–0.3
0.8
V
2.0
VCC + 0.3
V
0.4
V
0.8
V
1.7
6.0
V
VSS–0.3
VCC + 0.3
50
V
Input voltage high DISP
IOL = 1 mA
Input voltage low HDQ
–0.3
Input voltage range SB, PROG, VPFC, TS
UNIT
VRBI > 3 V, VCC < 2 V
RBI data-retention voltage
10
nA
1.3
V
0–1.25V
10
MΩ
0–1.25V
5
MΩ
5
MΩ
ZAI3
Input impedance: PROG, VPFC
0–VCC
NOTE: ZAI specifications are reference numbers based on process data.
VFC characteristics, VCC = 3.1–3.5 V, TOPR = 0°C to 70°C (unless otherwise noted)
PARAMETER
VSR
VSROS
VSRCOS
INL
TEST CONDITIONS
Input voltage range, VSR2 and VSR1
VSR input offset
Calibrated offset
Integral nonlinearity error
VSR = VSR2 – VSR1
VSR2 = VSR1, autocorrection disabled
After autocorrection
MIN
TYP
–0.25
–300
–50
–16
TOPR = 0°C to 50°C
MAX
UNIT
0.25
V
300
µV
16
V
0.21%
REG characteristics
PARAMETER
VRO
REG controlled output voltage
IREG
REG output current
TEST CONDITIONS
JFET: Rds(on) < 150 Ω
Vgs (off) < –3 V at 10 µA
MIN
3.1
1
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TYP
3.3
MAX
3.5
UNIT
V
µA
3
bq2016
GAS GAUGE IC FOR
HIGH DISCHARGE RATES
SLUS475A– JANUARY 2001 – REVISED NOVEMBER 2002
serial communication timing parameters
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
µs
t(CYCH)
t(CYCB)
Cycle time, host to bq2016 (write)
190
Cycle time, bq2016 to host (read)
190
t(STRH)
t(STRB)
Start hold, host to bq2016 (write)
5
Start hold, bq2016 to host (read)
32
t(DSU)
t(DSUB)
Data setup time
50
µs
Data setup time
50
µs
t(DH)
t(DV)
Data hold time
90
µs
Data valid time
80
µs
t(SSU)
t(SSUB)
Stop setup time
145
µs
Stop setup time
145
µs
t(RSPS)
t(B)
Response time, bq2016 to host
320
µs
Break
190
µs
t(BR)
Break recovery
40
µs
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
205
250
µs
ns
µs
bq2016
GAS GAUGE IC FOR
HIGH DISCHARGE RATES
SLUS475A– JANUARY 2001 – REVISED NOVEMBER 2002
timing requirements
t(BR)
t(B)
Figure 1. Break Timing
Write 1
Write 0
t(STRH)
t(DSU)
t(DH)
t(SSU)
t(CYCH)
Figure 2. Host to bq2016
Read 1
Read 0
t(STRB)
t(DSUB)
t(DV)
t(SSUB)
t(CYCB)
Figure 3. bq2016 to Host
Received by Host from bq2016
Written by Host to bq2016
CMDR = 03h
Data (NAC) = 65h
LSB
Break
0
1
MSB
LSB
1
1
2
0
3
0
4
0
5
0
6
0
MSB
LSB
7
0
0
1
t(RSPS)
MSB
1
0
MSB
2
1
3
0
4
0
5
1
6
1
7
0
LSB
65h = 0 1 1 0 0 1 0 1
03h = 00000011
Figure 4. Typical Communication With the bq2016
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
bq2016
GAS GAUGE IC FOR
HIGH DISCHARGE RATES
SLUS475A– JANUARY 2001 – REVISED NOVEMBER 2002
functional description
general operation
The bq2016 determines battery capacity by monitoring the amount of charge input to or removed from a
rechargeable battery. The bq2016 measures charge and discharge currents, estimates self-discharge, and
monitors the battery for low voltage and capacity thresholds. The bq2016 automatically compensates charge
and discharge currents for rate and temperature to adjust for battery efficiency under different conditions.
The bq2016 is configured to display capacity in a relative display mode. The display mode uses the last
measured discharge or learned capacity of the battery as the battery-full reference. The LED display can be
activated by a push-button connected to the DISP input or when the bq2016 detects a charge or discharge rate.
measurements
The bq2016 uses a fully differential, dynamically balanced voltage-to-frequency converter (VFC) for charge
measurement and a delta sigma analog-to-digital converter (ADC) for battery voltage, current, and temperature
measurement.
charge and discharge counting
The VFC measures the charge and discharge flow of the battery by monitoring a small-value sense resistor
between the SR1 and SR2. The VFC measures bipolar signals up to 250 mV in magnitude. The bq2016 detects
charge activity when VSR = VSR2 – VSR1 is positive and a discharge activity when VSR = VSR2 – VSR1 is negative.
The bq2016 integrates the signal over time using an internal counter. The bq2016 accumulates charge or
discharge at the rate of 3.125 µVh.
digital filter and VFC calibration
The bq2016 does not integrate charge or discharge counts below the digital filter threshold. The digital filter
threshold is set at 300 µV until a VFC calibration is performed. The calibration is performed after the first valid
charge after initialization. It takes up to 20 minutes to begin the calibration and up to 60 minutes to complete
the VFC calibration. The bq2016 suspends VFC calibration while it detects charge or discharge activity during
this period. After successful VFC calibration, the digital filter threshold is set to 100 µV.
voltage monitoring and thresholds
In conjunction with monitoring SR1 and SR2 for charge and discharge currents, the bq2016 monitors the battery
pack potential through the SB pin. The bq2016 measures the pack voltage and reports the result in the battery
voltage (VSBH:L) register. The bq2016 converts the signals at the SB input every 2 seconds.
The SB input is divided down from the cells using 1% tolerance resistors. To reduce current consumption from
the battery, the CVON output can switch the divider to the cells only during measurement period. CVON is high
impedance when the cells are measured, and driven low otherwise. The full-scale input for the SB pin is 1.25 V.
The bq2016 monitors the voltage at SB for the end-of-discharge voltage (EDV) and maximum voltage (MCV)
thresholds. The bq2016 uses the EDV threshold level to determine when the battery has reached an empty
state, and the MCV threshold level to detect a fault condition during charge. The EDV and MCV input levels are
set at:
EDV = 0.45 V
MCV = 1.00 V
The bq2016 disables EDV monitoring if VSR is greater than the overload threshold. If the bq2016 detects an
overload threshold, the bq2016 sets the OLVD flag in the secondary status flags (FLAGS2) register. The bq2016
resumes EDV detection after VSR drops back below the overload threshold. The overload threshold is a function
of battery capacity and is defined in the PFC table.
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
bq2016
GAS GAUGE IC FOR
HIGH DISCHARGE RATES
SLUS475A– JANUARY 2001 – REVISED NOVEMBER 2002
functional description (continued)
current
The SRC input of the bq2016 measures battery charge and discharge current. The SRC ADC input converts
the current signal from the series sense resistor every 2 seconds and stores the result in the current scale
register (VSRH:L). The full scale input range to SRC is limited to ±250 mV as shown in Table 1.
Table 1. SRC Input Range
SENSE RESISTOR
(mΩ)
FULL SCALE INPUT
(±A)
5
50
7.5
33
10
25
temperature
The bq2016 measures temperature, either with its internal thermistor or with an external thermistor, depending
on the state of the PROG input. The bq2016 accepts an external NTC thermistor on the TS input. The bq2016
samples the TS input voltage every 2 seconds and stores the voltage in the TS Input Voltage (TEMPVH:L)
register and the actual temperature in the temperature (TEMP) register. With an external thermistor, the bq2016
develops the temperature value for the temperature register on the basis of a Semitec 103AT (10K) NTC model.
The bq2016 reports the temperature in 1°C steps with an accuracy of 4°C or 6°C for an external and internal
thermistor, respectively. The temperature reading is used to adapt remaining capacity for charge and discharge
efficiency and to adjust for the battery’s self discharge.
If an internal thermistor is selected for temperature measurement, the TS input should be grounded.
THON may be used to connect the bias source to the thermistor when the bq2016 samples the TS input. THON
is high impedance when the temperature is measured, and driven low otherwise.
gas gauge operation
general
The operational overview diagram in Figure 5 illustrates the operation of the bq2016. The bq2016 accumulates
a measure of charge and discharge currents and estimates self-discharge. The bq2016 compensates the
charge and discharge currents for rate and temperature efficiencies. It also adjusts the self-discharge estimation
for temperature variation. The bq2016 stores the compensated charge accumulation in the nominal available
capacity (NAC) register. For LED indication, the bq2016 adjusts NAC for the battery pack operating
temperature.
The discharge count register (DCR) tracks discharge activity of the battery. The last measured discharge (LMD)
represents the discharge capacity or learned full capacity of the battery in the application. The bq2016 transfers
the value in DCR to LMD when a qualified discharge occurs.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
bq2016
GAS GAUGE IC FOR
HIGH DISCHARGE RATES
SLUS475A– JANUARY 2001 – REVISED NOVEMBER 2002
functional description (continued)
Inputs
Charge
Current
Discharge
Current
Self-Discharge
Timer
Rate and
Temperature
Compensation
Rate and
Temperature
Compensation
Temperature
Compensation
–
+
Main Counters and
Capacity Reference (LMD)
–
Nominal
Available
Charge
(NAC)
+
≤
Last
Measured
Discharge
(LMD)
Qualified
Transfer
+
Discharge
Count
Register
(DCR)
Temperature, Voltage,
Other Data
Temperature
Translation
Outputs
Chip-Controlled
Available Charge
LED Display
Serial
Port
Figure 5. Operational Overview Diagram
main gas gauge registers
programmed full count (PFC)
The programmed full count (PFC) register stores the user-specified battery full capacity. The 8-bit PFC registers
stores the full capacity in mVh scaled as shown in Table 2. The VPFC input sets the PFC value and the counting
scale on a bq2016 initialization (power on reset).
nominal available capacity (NAC)
The main counter, NAC, represents the available battery capacity at any given time. Battery charging
increments the NAC register, while battery discharging and self-discharge decrement the NAC register. The
bq2016 compensates the charge and discharge inputs to NAC for rate and temperature efficiencies.
NAC counts up during charge to a maximum value of LMD and down during discharge and self-discharge to
0. The bq2016 resets NAC to 0 on initialization and when the bq2016 sets the EDV bit on discharge. To prevent
overstatement of charge during periods of overcharge, NAC stops incrementing when NAC = LMD.
8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
bq2016
GAS GAUGE IC FOR
HIGH DISCHARGE RATES
SLUS475A– JANUARY 2001 – REVISED NOVEMBER 2002
main gas gauge registers (continued)
NAC calibration
The bq2016 sets NAC to 85% of LMD when it detects a transition from fast-charge to a trickle charge provided
that 85% ≥ NAC > 80% of LMD when the bq2016 detects the transition. For this determination, fast-charge
detection (FCDT) corresponds to the FCDT value set by the PROG pin. Fast-charge detection occurs when the
FCDT condition is met for 30s after the CHGS bit is set in FLGS1. Once fast-charge activity is qualified, a
transition of the SRC signal below the FCDT threshold enables trickle-charge detection. The bq2016 verifies
trickle charge by continuing to sample the SRC input for signals above the trickle-charge threshold and below
the fast-charge threshold. This sampling can take up to 3 minutes. Once a trickle-charge is verified, the bq2016
adjusts NAC up to 85% of LMD if NAC was between 80% and 85% of LMD. If NAC was greater then 85% of
LMD, NAC is unchanged upon transition detection.
last measured discharge (LMD)
Last measured discharge is the most recent measured discharge capacity of the battery. On initialization, the
bq2016 sets LMD = PFC. When a valid charge is detected following a valid discharge, the bq2016 updates LMD
with the current value in DCR. During subsequent discharges, the bq2016 updates LMD with the current value
in DCR. (The DCR value represents the measured discharge capacity of the battery from full to the EDV
threshold.) The bq2016 limits the adjustment of LMD down to 75% of its previous value. A qualified discharge
is necessary for a capacity transfer from DCR to the LMD register. The LMD register also serves as the 100%
reference threshold used by the display mode.
discharge count register (DCR)
The discharge count register (DCR) is used to update the last measured discharge register only if a complete
battery discharge from full to empty occurs without any partial battery charges. In this way, the bq2016 adapts
its capacity determination based on the actual conditions of discharge.
The DCR counts up during discharge independent of NAC and can continue to increase after NAC decrements
to 0. Before NAC = 0 (empty battery), both discharge and self-discharge increment the DCR. After NAC = 0,
only discharge increments the DCR. The DCR resets to 0 when the VDQ bit in the primary status flags register
(FLAGS1) is set on charge. The bq2016 sets VDQ=1 on a fast charge-to-trickle detection if NAC is greater than
80% of LMD or when NAC=LMD. The DCR does not roll over but stops counting when it reaches ffffh. The DCR
value becomes the new LMD value on the first valid charge after a discharge to EDV threshold if the bq2016
detects a qualified discharge. A valid charge is a minimum of one (maximum of two) NAC increments. A qualified
discharge occurs if
D No valid charge initiations occurred during the period between when VDQ gets set on charge and when the
bq2016 detects EDV on discharge.
D The self-discharge count is not more than 10% of PFC.
D The temperature is greater than or equal to 0°C when the EDV level is reached during discharge.
D The EDV bit gets set.
The VDQ bit set to a one indicates whether the present discharge is valid for LMD update.
programming the bq2016
The bq2016 is programmed with the VPFC and the PROG pins. During power-up or initialization, the bq2016
reads the state of these multilevel inputs and latches in the programmable configuration settings. Resistor
divider networks for VPFC and PROG should target the nominal thresholds as defined in the programming
tables.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
bq2016
GAS GAUGE IC FOR
HIGH DISCHARGE RATES
SLUS475A– JANUARY 2001 – REVISED NOVEMBER 2002
programmable configuration settings
design capacity
The battery’s rated design capacity or programmed full count (PFC) is programmed with the VPFC pin as shown
in Table 2, and represents the battery’s full reference. The VPFC pin is a 16-level input.
Table 2. PFC Selections
PFC
LEVEL
LOWER
1
0/32
NOMINAL
THRESHOLD
(VCC)
≤ 1/32 <
UPPER
PFC
(COUNT)
SCALE
(mVh/
COUNT)
CAPACITY
(mVh)
OVERLOAD
THRESHOLD
(mV)
Rv
(kΩ)
2
2/32
≤ 3/32 <
2/32
30720
1/2560
12.0
50
Open
0
NiCd
4/32
25344
1/2560
9.9
50
1000
102
3
4/32
≤ 5/32 <
NiCd
6/32
41472
1/5120
8.1
50
1000
187
NiCd
4
6/32
5
8/32
≤ 7/32 <
8/32
33792
1/5120
6.6
50
1000
280
NiCd
≤ 9/32 <
10/32
27648
1/5120
5.4
30
1000
392
NiCd
6
7
10/32
≤ 11/32 <
12/32
46080
1/10240
4.5
30
1000
523
NiCd
12/32
≤ 13/32 <
14/32
36864
1/10240
3.6
30
1000
681
NiCd
8
14/32
≤ 15/32 <
16/32
30720
1/10240
3.0
30
1000
887
NiCd
Rg
(kΩ)
CHEMISTRY
9
16/32
≤ 17/32 <
18/32
39936
1/10240
3.9
30
887
1000
NiMH
10
18/32
≤ 19/32 <
20/32
46080
1/10240
4.5
30
681
1000
NiMH
11
20/32
≤ 21/32 <
22/32
27648
1/5120
5.4
30
523
1000
NiMH
12
22/32
≤ 23/32 <
24/32
33792
1/5120
6.6
30
392
1000
NiMH
13
24/32
≤ 25/32 <
26/32
39936
1/5120
7.8
50
280
1000
NiMH
14
26/32
≤ 27/32 <
28/32
47616
1/5120
9.3
50
187
1000
NiMH
15
28/32
≤ 29/32 <
30/32
28416
1/2560
11.1
50
102
1000
NiMH
16
30/32
≤ 31/32 ≤
32/32
33792
1/2560
13.2
50
0
Open
NiMH
The correct PFC may be determined by multiplying the rated battery capacity in mAh by the sense-resistor
value:
Battery capacity (mAh) × sense resistor (Ω) = PFC (mVh)
Selecting a PFC slightly less than the rated capacity provides a conservative capacity reference. The bq2016
stores the selected PFC in the PFC register.
10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
bq2016
GAS GAUGE IC FOR
HIGH DISCHARGE RATES
SLUS475A– JANUARY 2001 – REVISED NOVEMBER 2002
programmable configuration settings (continued)
internal or external thermistor
The PROG pin programs whether the bq2016 uses an internal or external thermistor according to the following
table. It also defines the fast charge and trickle-rate detection thresholds for NAC calibration.
Table 3. PROG Selections
FAST CHARGE
DETECTION THRESHOLD
(FCDT)
PROG LEVEL
LOW
NOM (VCC)
HI
T
TRICKLE RATE
1
0/12
≤ 1/12 <
2/12
I
VDMF < VSR < 2 mV
0
2/12
≤ 3/12 <
4/12
I
VDMF < CRate < C/8
VSR > 2 mV for 30s
CRate > C/5 for 30s
Open
2
1000
332
3
4/12
≤ 5/12 <
6/12
I
—
—
1000
715
4
6/12
≤ 7/12 <
8/12
E
VDMF < VSR < 2 mV
> 2 mV for 30s
715
1000
332
1000
0
Open
5
8/12
≤ 9/12 <
10/12
E
VDMF < CRate < C/8
6
10/12
≤ 11/12 ≤
12/12
E
—
CRate > C/5 for 30s
—
Rv (k)
Rg (k)
NOTE: The bq2016 does not perform NAC calibration on charge with options 3 and 6. VDMF = 300 µV uncalibrated or 100 µV calibrated.
programming example
Given:
Sense resistor = 0.003 Ω
Chemistry = NiCd
Capacity = 2000 mAh
Discharge current range = 1 A to 10 A
Charge current = 200 mA to 4 A
Voltage drop over sense resistor = –30 mV to 12 mV
Internal thermistor with 2 mV FCDT
Therefore
2000 mAh × 0.003 = 6 mVh
Select
VPFC level = 5
PROG level = 1
TS pin = grounded
The initial full battery capacity is 5.4 mVh (1800 mAh) until the bq2016 learns a new capacity with a qualified
discharge from full to EDV.
charge and discharge count counting
charge counting
The bq2016 detects charge activity when VSR = VSR2 – VSR1 is greater than the digital filter threshold. If charge
activity is detected, the bq2016 increments NAC at a rate proportional to VSR and activates the LED display
if VSR > 2 mV. Charge actions increment the NAC after compensation for charge rate and temperature. Charge
counting continues until VSR drops below VDMF.
discharge counting
The bq2016 detects discharge activity when VSR = VSR2 – VSR1 is more negative than the digital filter threshold.
If discharge activity is detected, the bq2016 decrements NAC and increments DCR at a rate proportional to
VSR and activates the LED display if VSR < –2 mV. Discharge actions decrement NAC and increment DCR after
compensation for discharge rate and temperature. Discharge counting continues until VSR rises above –VDMF.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
bq2016
GAS GAUGE IC FOR
HIGH DISCHARGE RATES
SLUS475A– JANUARY 2001 – REVISED NOVEMBER 2002
charge and discharge count counting (continued)
self-discharge estimation
The bq2016 continuously decrements NAC and increments DCR for self-discharge based on time and
temperature. The self-discharge count rate is programmed to be a nominal 1/80 NAC rate per day for NiCd
and a nominal 1/60 × NAC for NiMH. This is the rate for a battery whose temperature is between 20°C–30°C.
The self-discharge rate doubles every 10°C increase in temperature.
count compensations
The bq2016 compensates charge and discharge counting for temperature and rate before updating the NAC
and/or DCR. The bq2016 compensates self-discharge estimation for temperature before updating the NAC or
DCR.
charge compensations
The bq2016 compensates for charge efficiencies at a quick-charge and fast-charge rate at two different
temperature thresholds. The bq2016 applies the NiCd or NiMH factors based on the VPFC setting. For charge
compensation, quick charge is defined as a C/5 charge rate or less and fast charge is defined as a rate greater
than C/5.
The charge-compensation factors are shown in Tables 4 and 5.
charge compensations
Table 4. Charge Compensation for NiCd
CHARGE TEMPERATURE
QUICK CHARGE
( ≤ C / 5 ) COMPENSATION
FAST CHARGE
( > C / 5 ) COMPENSATION
<40C
0.80
0.95
≥ 40
0.75
0.90
Table 5. Charge Compensation for NiMH
CHARGE TEMPERATURE
QUICK CHARGE
( ≤ C / 5 ) COMPENSATION
FAST CHARGE
( > C / 5 ) COMPENSATION
<40C
0.80
0.90
≥ 40
0.75
0.85
discharge compensation
The bq2016 corrects for the rate of discharge by adjusting an internal discharge-compensation factor. The
discharge factor is based on the calculated discharge rate determined from the VSR potential and the PFC
setting. The table below shows the compensation factors for NiCd and NiMH during discharge:
DISCHARGE RATE
DISCHARGE EFFICIENCY
( FDE ) (%)
≤1C
100
>3C
100
>6C
95
>9C
95
>12C
90
NOTE: The C Rate determination is made from LMD.
12
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
bq2016
GAS GAUGE IC FOR
HIGH DISCHARGE RATES
SLUS475A– JANUARY 2001 – REVISED NOVEMBER 2002
discharge compensation (continued)
The bq2016 adjusts the discharge-compensation efficiency for temperature. At lower temperatures, the
discharge-efficiency factor decreases by 5% for each 10°C temperature step below 10°C.
FDE (new) = FDE – (5% × N)
where N = number of 10°C steps below 10°C.
For example at a 1C discharge,
T > 10°C:
0°C < T < 10°C:
–10°C < T < 0°C:
–20°C < T < –10°C:
–20°C < T < –30°C:
N = 0 and FDE(NEW) = 100%
N = 1 and FDE(NEW) = 95%
N = 2 and FDE(NEW) = 90%
N = 3 and FDE(NEW) = 85%
N = 4 and FDE(NEW) = 80%
error summary
capacity inaccurate
The LMD is susceptible to error on initialization or if no updates occur. On initialization, the LMD value includes
the error between the programmed full capacity and the actual capacity. This error is present until a valid
discharge occurs and LMD is updated. The other cause of LMD error is battery wear-out. As the battery ages,
the measured capacity must be adjusted to account for changes in actual battery capacity. The bq2016
increments the capacity inaccurate count (CPI) register each time a valid charge occurs and is reset whenever
LMD is updated from the DCR. The counter does not wrap around but stops counting at 255. The capacity
inaccurate flag (CI) is set if LMD has not been updated following 64 valid charges.
display
The bq2016 can directly display capacity information using low-power LEDs. The bq2016 displays the battery
charge as a percentage of the LMD.
The capacity display is also adjusted for the present battery temperature. The temperature adjustment reflects
the available capacity at a given temperature but does not affect the NAC register. Tables 6 and 7 show the
temperature adjustments:
Table 6. Temperature Translation for NiCd
TEMPERATURE
(C)
TEMPERATURE TRANSLATION
(%)
T ≥ 10
100
10 > T ≥ 0
100
0 > T ≥ –10
90
–10 > T ≥ –20
75
T < –20
50
Table 7. Temperature Translation for NiMH
TEMPERATURE
(C)
TEMPERATURE TRANSLATION
(%)
T ≥ 10
100
10 > T ≥ 0
75
0 > T ≥ –10
40
–10 > T ≥ –20
0
T < –20
0
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
bq2016
GAS GAUGE IC FOR
HIGH DISCHARGE RATES
SLUS475A– JANUARY 2001 – REVISED NOVEMBER 2002
error summary (continued)
The display becomes active during charge if the NAC registers are counting at a rate equivalent to VSR > 2 mV
or discharge if the NAC registers are counting at a rate equivalent to VSR < –2 mV. When DISP is pulled low,
the segment output becomes active for 4 seconds. LED1 blinks at a 4-Hz rate whenever NAC is less than 6%
of LMD or VSB ≤ VEDV.
Table 8. Display Mode
LED1
LED2
LED3
LED4
LED5
NAC / LMD
ON
ON
ON
ON
ON
80 – 100%
ON
ON
ON
ON
OFF
60 – < 80%
ON
ON
ON
OFF
OFF
40 – < 60%
ON
ON
OFF
OFF
OFF
20 – < 40%
6 < 20%
ON
OFF
OFF
OFF
OFF
BLINK
OFF
OFF
OFF
OFF
< 6%
BLINK
OFF
OFF
OFF
OFF
VSB ≤ VEDV
RBI input
The RBI input pin should be used with a storage capacitor or external supply to provide backup potential to the
internal bq2016 registers when VCC drops below 3.0 V. VCC is output on RBI when VCC is above 3.0 V. If an
external supply (such as the bottom series cell) is the backup source, then an external diode is required for
isolation.
initialization
The bq2016 can be initialized by removing VCC and grounding the RBI pin for 5 seconds or by a command over
the serial port. The HDQ port reset command requires writing 78h to register CMDWD.
microregulator
A REG output is provided to regulate an external low-threshold JFET to supply power to the bq2016 based circuit
from the series cells. The REG output maintains VCC to the bq2016 at 3.3 V.
communicating with the bq2016
The bq2016 includes a simple single-pin (HDQ referenced to Vss) serial data interface. A host processor uses
the interface to access various bq2016 registers. By adding a single contact to the battery pack, the host can
easily monitor the battery characteristics. The open-drain HDQ pin on the bq2016 should be pulled up by the
host system or pulled down to ground.
The interface uses a command-based protocol, in which the host processor sends a command byte to the
bq2016. The command directs the bq2016 to either store the next eight bits of data received to a register
specified by the command byte or output the eight bits of data specified by the command byte. The
communication protocol is asynchronous return-to-one. Command and data bytes consist of a stream of eight
bits that have a maximum transmission rate of 5K bits/s. The least-significant bit of a command or data byte
is transmitted first. The protocol is simple enough that it can be implemented by most host processors using
either polled or interrupt processing. Data input from the bq2016 may be sampled using the pulse-width capture
timers available on some microcontrollers.
If a communication error occurs (e.g., tCYCB > 250µs), the bq2016 should be sent a BREAK to reinitiate the serial
interface. A BREAK is detected when the HDQ pin is driven to a logic-low state for a time tB or greater. The HDQ
pin should then be returned to its normal ready-high logic state for a time tBR. The bq2016 is now ready to
receive a command from the host processor.
14
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
bq2016
GAS GAUGE IC FOR
HIGH DISCHARGE RATES
SLUS475A– JANUARY 2001 – REVISED NOVEMBER 2002
communicating with the bq2016 (continued)
The return-to-one data bit frame consists of three distinct sections. The first section is used to start the
transmission by either the host or the bq2016 taking the HDQ pin to a logic-low state for a period tSTRH;B. The
next section is the actual data transmission, where the data should be valid by a period tDSU;B, after the negative
edge used to start communication. The data should be held for a period tDH;DV, to allow the host or bq2016 to
sample the data bit.
The final section is used to stop the transmission by returning the HDQ pin to a logic-high state by at least a
period tSSU;B, after the negative edge used to start communication. The final logic-high state should continue
during a period tCYCH;B, to allow time to ensure that the bit transmission was stopped properly. The timings for
data and break communication are given in the serial communication timing specification and illustration
sections.
In communication with the bq2016 the least-significant bit is always transmitted first.
command code and registers
The bq2016 status registers are listed in Table 9 and are described below.
command code
The bq2016 latches the command code when eight valid command bits have been received by the bq2016. The
command code contains two fields:
D W/R bit
D Command address
The W/R bit of the command code determines whether the received command is for a read or a write function.
command code (continued)
W/R is:
0
1
The bq2016 outputs the requested register contents specified by the address portion of command code.
The host writes to the register specified by the address portion of the command code.
The lower seven-bit field of the command code contains the address portion of the register to be accessed. The
bq2016 ignores writes to invalid addresses.
registers
FLAGS1 (0x01) – Primary Status Flags
The FLAGS1 register provides bq2016 status information. The 8-bit register includes the following status bits:
7
6
5
4
3
2
1
0
CHGS
BRP
MCV
CI
VDQ
RSVD
EDV
OCE
CHGS
The bq2016 set the CHGS bit when it detects charge activity. The bq2016 clears the CHGS bit on discharge.
Bit = Condition
0
The bq2016 detects discharge.
1
The bq2016 detects charge.
BRP
The bq2016 sets the BRP bit when it performs a full reset.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
15
bq2016
GAS GAUGE IC FOR
HIGH DISCHARGE RATES
SLUS475A– JANUARY 2001 – REVISED NOVEMBER 2002
registers (continued)
MCV
The bq2016 sets the MCV bit when it detects that the maximum cell voltage threshold is being exceeded.
Bit = Condition
0
Cell voltage is below the threshold.
1
Cell voltage is above the threshold.
CI
The bq2016 sets the CI bit on reset and when the CPI register exceeds 64.
Bit = Condition
0
An LMD update has occurred.
1
The bq2016 has been reset or the CPI register exceeds 64.
VDQ
The bq2016 sets the VDQ bit when the present discharge cycle is considered valid for an LMD update.
Bit = Condition
0
The present discharge cycle is not valid for an LMD update.
1
The present discharge cycle is valid for an LMD update.
Bit 2 is reserved.
EDV
The bq2016 sets the EDV bit when the battery voltage drops below the EDV threshold. The bit is latched and
remains set until valid charge activity is detected.
Bit = Condition
0
The battery voltage is greater than the EDV threshold.
1
The battery voltage is less than the EDV threshold.
OCE
The bq2016 sets the OCE bit when an VFC offset calibration has been performed.
Bit = Condition
0
Offset calibration not completed
1
Offset calibration completed
TEMP (0x02) – Temperature
The TEMP register contains the battery temperature as computed using the internal temperature sensor of the
bq2016. It is represented in degrees C. The data is an 8-bit signed integer. For example, –10°C is represented
as F6h.
NAC (0x03) – Nominal Available Capacity
NAC is an 8-bit register that contains the present remaining capacity of the battery pack. The NAC contents are
compensated for rate and temperature. The data is represented in the same units as PFC.
LMD (0x05) – Last Measured Discharge
LMD stores the learned discharge capacity of the battery pack and represents the full charge reference. The
8-bit register presents data in the same units as PFC.
FLAGS2 (0x06) – Second Status Flags
The FLAGS2 register provides bq2016 status information. The 8-bit register includes the following status bits:
16
7
6
5
4
3
2
1
0
RSVD
DR2
DR1
DR0
RSVD
RSVD
RSVD
OVLD
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
bq2016
GAS GAUGE IC FOR
HIGH DISCHARGE RATES
SLUS475A– JANUARY 2001 – REVISED NOVEMBER 2002
registers (continued)
DR2–0
The DR2–0 bits represent the present discharge rate of the battery according to the following code:
DISCHARGE RATE INDICATION
DISCHARGE RATE (R)
DR2
DR1
DR0
R ≤ 1C
0
0
0
1C < R ≤ 3C
0
0
1
3C < R ≤ 6C
0
1
0
6C < R ≤ 9C
0
1
1
9C < R ≤ 12C
1
0
0
R > 12C
1
0
1
OVLD
The bq2016 set the OVLD bit when it detects that the present discharge rate exceeds the programmed overload
threshold.
Bit = Condition
0
Discharge rate is below the overload threshold.
1
Discharge rate is above the overload threshold.
VPFC (0x07) – VPFC Pin Input Level
VPFC stores the input level at the VPFC programming pin. The voltage at the VPFC (VVPFC) pin is calculated
by
VVPFC (mV) = Vcc × (VPFC/256)
VPROG (0x08) – VPROG Pin Input Level
VPROG stores the input level at the VPROG programming pin. The voltage at the VPROG (VPROG) pin is
calculated by:
VVPROG (mV) = Vcc × (VPROG/256)
CPI (0x09) – Capacity Input Level
CPI stores the number of valid charge actions since the last LMD update.
OCTL (0x0a) – Output Control
OCTL provides a means of testing LED functionality. The register consists of:
7
6
5
4
3
2
1
0
RSVD
RSVD
OCTL5
OCTL4
OCTL3
OCTL2
OCTL1
Enable
When Enable is low, the bq2016 writes the data in OCTL5–1 to the LED5–1 pins. A one in OCTL5–1 turns the
corresponding LED on. This function overrides the LED indication as a representation of capacity.
FULCNT (0x0b) – Full Count Register
FULCNT store the number of times the battery has been charged to full (NAC=LMD) in 16 count increments.
CMDWD (0x0c) – Command Word
The CMDWD register can be used to reset the bq2016 or initiate a VFC offset calibration.
To reset the bq2016, 0x78 must be written to this location. When reset, the bq2016 sets the following values:
NAC = 0
LMD = PFC
CPI = 0
FULCNT = 0
DCR = 0
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
17
bq2016
GAS GAUGE IC FOR
HIGH DISCHARGE RATES
SLUS475A– JANUARY 2001 – REVISED NOVEMBER 2002
To calibrate the VFC, 0x68 must be written to this location. During VFC offset calibration, the bq2016 deselects
the SR1 and SR2 inputs and disables the LEDs. When the bq2016 successfully completes VFC calibration, it
sets the OCE bit in FLAGS1. The command 0x60 terminates a VFC calibration. The bq2016 automatically
performs VFC calibration after trickle detection and initial power-up, and when NAC = LMD.
PFC (0x0f) – Programmed Full Count
The PFC register stores the battery design capacity as defined by the VPFC input.
VSB (0x10 and 0x11) – Battery Voltage
VSBH (0x11) and VSBL (0x10) form the 16-bit register that contains the voltage present at the SB input pin in
mV.
VSR (0x12 and 0x13) – Current Scale
VSRH (0x13) and VSBL (0x12) form the 16-bit register that contains the voltage present across the SR inputs
pin in mV.
TEMPV (0x14 and 0x15) – Thermistor Voltage
TEMPVH (0x15) and TEMPVL (0x14) form the 16-bit register that contains the voltage present at the TS inputs
pin in mV.
DCR (0x18) – Discharge Count Register
DCR stores the cumulative discharge count from the time VDQ is set on a charge. The data is represented in
the same units as PFC. The number of counts equals DRC × 256.
FLAGS3 (0x4c) – Third Status Flags
The FLAGS3 register provides bq2016 status information. The 8-bit register includes the following status bits:
7
6
5
4
3
2
1
0
RSVD
RSVD
RSVD
RSVD
VQ
CR1
CR0
RSVD
CR1–CR0
The CR1–CR0 bits represent the present charge rate of the battery according to the following code:
CHARGE RATE INDICATION
CR1
CR0
R≤C/8
CHARGE RATE (R)
0
0
C/5≥R>C/8
0
1
R>C/5
1
1
VQ
The bq2016 sets the VQ bit when it detects a valid charge condition. A valid charge is two NAC increments.
Bit = Condition
0 = No valid charge condition
1 = Valid charge condition present
18
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
bq2016
GAS GAUGE IC FOR
HIGH DISCHARGE RATES
SLUS475A– JANUARY 2001 – REVISED NOVEMBER 2002
registers (continued)
Table 9. Command and Status Registers
LOC
(HEX)
READ/
WRITE
7
6
5
Primary status flags
0x01
R
CHGS
BRP
Temperature
0x02
R
TP7
TP6
NAC
Nominal available charge
0x03
R/W
NCH7
LMD
Last measured discharge
0x05
R/W
Secondary status flags
0x06
R
VPFC
VPFC pin input level
0x07
R
VPFC7
VPFC6
VPFC5
VPFC4
VPFC3
VPFC2
VPFC1
VPFC0
VPROG
PROG pin input level
0x08
R
VPRO7
VPRO6
VPRO5
VPRO4
VPRO3
VPRO2
VPRO1
VPRO0
Capacity inaccurate count
0x09
R
CPI7
CPI6
CPI5
CPI4
CPI3
CPI2
CPI1
CPI0
OCTL
LED output control
0x0a
R/W
NA
NA
OCTL5
OCTL4
OCTL3
OCTL2
OCTL1
Enable
FCNT
Full count register
0x0b
R/W
FCNT7
FCNT6
FCNT5
FCNT4
FCNT3
FCNT2
FCNT1
FCNT0
Command word
0x0c
R/W
CMD7
CMD6
CMD5
CMD4
CMD3
CMD2
CMD1
CMD0
SYMBOL
FLAGS1
TEMP
FLAGS2
CPI
CMDWD
REGISTER NAME
4
3
2
1
0
MCV
CI
VDQ
RSVD
EDV
OCE
TP5
TP4
TP3
TP2
TP1
TP0
NCH6
NCH5
NCH4
NCH3
NCH2
NCH1
NCH0
LMD7
LMD6
LMD5
LMD4
LMD3
LMD2
LMD1
LMD0
RSVD
DR2
DR1
DR0
RSVD
RSVD
RSVD
OVLD
PFC
Program PFC
0x0f
R/W
PFC7
PFC6
PCF5
PFC4
PFC3
PFC2
PFC1
PFC0
VSBL
Battery voltage (low byte)
0x10
R
VSBL7
VSBL6
VSBL5
VSBL4
VSBL3
VSBL2
VSBL1
VSBL0
VSBH
Battery voltage (high byte)
0x11
R
VSBH7
VSBH6
VSBH5
VSBH4
VSBH3
VSBH2
VSBH1
VSBH0
VSRL
Current scale (low byte)
0x12
R
VSRL7
VSRL6
VSRL5
VSRL4
VSRL3
VSRL2
VSRL1
VSRL0
VSRH
Current scale (high byte)
0x13
R
VSRH7
VSRH6
VSRH5
VSRH4
VSRH3
VSRH2
VSRH1
VSRH0
TEMPVL
TS input voltage (low byte)
0x14
R
TPVL7
TPVL6
TPVL5
TPVL4
TPVL3
TPVL2
TPVL1
TPVL0
TEMPVH
TS input voltage (high byte)
0x15
R
TPVH7
TPVH6
TPVH5
TPVH4
TPVH3
TPVH2
TPVH1
TPVH0
Discharge count register
0x18
R
DCR7
DCR6
DCR5
DCR4
DCR3
DCR2
DCR1
DCR0
Third status flags
0x4c
R
RSVD
RSVD
RSVD
RSVD
VQ
CR1
CR0
RSVD
DCR
FLAGS3
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
19
bq2016
GAS GAUGE IC FOR
HIGH DISCHARGE RATES
SLUS475A– JANUARY 2001 – REVISED NOVEMBER 2002
APPLICATION INFORMATION
bq2016 applications schematic
PACK+
VCC
MMBT3904
HDQ
100 Ω
BZX84C5V6
1.5 MΩ
SST113
D G
S
0.01 µF
100 Ω
ZVP3306F
R1
RBI
VCC
REG
0.1 µF
Rv
VSS
SR1
DISP
SR2
LED1
SRC
330 Ω
330 Ω
20
TS
LED3
LED5
Rg
100 kΩ
0.1 µF
100 kΩ
PACK–
Rs
0.1 µF
VCC
100 kΩ
0.1 µF
LED2
LED4
Rg
VPFC
330 Ω
330 Ω
Cells
Rv
PROG
VCC
100 kΩ
Display
330 Ω
VCC
SB
HDQ
1 µF
R2
0.01 µF
U1
bq2016
VCC
THON
1 MΩ
CVON
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
2N7002
PACKAGE OPTION ADDENDUM
www.ti.com
26-Sep-2015
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
BQ2016DBQ
NRND
SSOP
DBQ
28
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
0 to 70
2016
E412
BQ2016DBQG4
NRND
SSOP
DBQ
28
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
0 to 70
2016
E412
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
26-Sep-2015
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
Similar pages