TI1 BQ2002GSNTRG4 Nicd/nimh fast-charge management ic Datasheet

bq2002E/G
NiCd/NiMH Fast-Charge Management ICs
Features
General Description
➤
The bq2002E and bq2002G FastCharge ICs are low-cost CMOS battery-charge controllers providing reliable charge termination for both NiCd
and NiMH battery applications. Controlling a current-limited or constant-current supply allows t h e
bq2002E/G to be the basis for a costeffective stand-alone or system-integrated charger. The bq2002E/G integrates fast charge with optional top-off
and pulsed- trickle control in a single
IC for charging one or more NiCd or
NiMH battery cells.
➤
➤
Fast charge of nickel cadmium
or nickel-metal hydride batteries
Direct LED output displays
charge status
Fast-charge termination by -∆V,
maximum voltage, maximum
temperature, and maximum
time
➤
Internal band-gap voltage reference
➤
Optional top-off charge
➤
Selectable pulse trickle charge
rates
➤
Low-power mode
➤
8-pin 300-mil DIP or 150-mil
SOIC
Pin Connections
Fast charge is initiated on application
of the charging supply or battery replacement. For safety, fast charge is
inhibited if the battery temperature
and voltage are outside configured
limits.
Fast charge is terminated by any of
the following:
n
Peak voltage detection (PVD)
n
Negative delta voltage (-∆V)
n
Maximum voltage
n
Maximum temperature
n
Maximum time
After fast charge, the bq2002E/G optionally tops-off and pulse-trickles the
battery per the pre-configured limits.
Fast charge may be inhibited using
the INH pin. The bq2002E/G may
also be placed in low-standby-power
mode to reduce system power consumption.
T h e bq2002E differs from t h e
bq2002G only in that a slightly different set of fast-charge and top-off
time limits is available. All differences between the two ICs are illustrated in Table 1.
Pin Names
TM
1
8
CC
LED
2
7
INH
BAT
3
6
VCC
VSS
4
5
TS
TM
Timer mode select input
TS
Temperature sense input
LED
Charging status output
VCC
Supply voltage input
BAT
Battery voltage input
INH
Charge inhibit input
VSS
System ground
CC
Charge control output
8-Pin DIP or
Narrow SOIC
PN-200201.eps
bq2002E/G Selection Guide
TCO
HTF
LTF
bq2002E 0.175 ∗
VCC
Part No.
LBAT
0.5 ∗
VCC
0.6 ∗
VCC
None
bq2002G 0.175 ∗
VCC
0.5 ∗
VCC
0.6 ∗
VCC
None
-∆V PVD
✔
✔
✔
✔
✔
✔
SLUS132 - FEBRUARY 1999
1
Fast Charge
tMTO
Top-Off
Maintenance
C/2
1C
2C
C/2
1C
2C
200
80
40
160
80
40
None
C/16
None
None
C/16
None
C/32
C/32
C/32
C/32
C/32
C/32
bq2002E/G
sumes operation at the point where initially
suspended.
Pin Descriptions
TM
Timer mode input
Charge control output
CC
A three-level input that controls the settings
for the fast charge safety timer, voltage termination mode, top-off, pulse-trickle, and
voltage hold-off time.
LED
An open-drain output used to control the
charging current to the battery. CC switching to high impedance (Z) enables charging
current to flow, and low to inhibit charging
current. CC is modulated to provide top-off,
if enabled, and pulse trickle.
Charging output status
Open-drain output that indicates the charging
status.
BAT
Functional Description
Battery input voltage
Figure 2 shows a state diagram and Figure 3 shows a
block diagram of the bq2002E/G.
The battery voltage sense input. The input to
this pin is created by a high-impedance resistor divider network connected between
the positive and negative terminals of the
battery.
VSS
System ground
TS
Temperature sense input
Battery Voltage and Temperature
Measurements
Battery voltage and temperature are monitored for
maximum allowable values. The voltage presented on
the battery sense input, BAT, should represent a
single-cell potential for the battery under charge. A
resistor-divider ratio of
Input for an external battery temperature
monitoring thermistor.
VCC
RB1
=N-1
RB2
Supply voltage input
is recommended to maintain the battery voltage within
the valid range, where N is the number of cells, RB1 is
the resistor connected to the positive battery terminal,
and RB2 is the resistor connected to the negative battery terminal. See Figure 1.
5.0V ± 20% power input.
INH
Charge inhibit input
When high, INH suspends the fast charge in
progress. When returned low, the IC re-
Note: This resistor-divider network input impedance to
end-to-end should be at least 200kΩ and less than 1 MΩ.
VCC
PACK +
RT
RB1
VCC
R3
BAT
bq2002E/G
TM
RB2
TS
N
T
C
bq2002E/G
R4
VSS
VSS
BAT pin connection
Mid-level
setting for TM
Thermistor connection
NTC = negative temperature coefficient thermistor.
Fg2002E/G01.eps
Figure 1. Voltage and Temperature Monitoring and TM Pin Configuration
2
bq2002E/G
Chip on
4.0V
VCC
Battery Voltage
too High?
VBAT > 2V
VBAT < 2V
Battery Voltage
too Low?
VBAT < 0.175 VCC
0.175 VCC < VBAT
VTS > 0.6
(PVD or - V or
Maximum Time Out)
and TM = Low
VCC
Battery
Temperature?
VTS < 0.6
VCC
Charge
Pending
Fast
LED =
Low
VBAT > 2V or
VTS < VCC/2 or
((PVD or - V or
Maximum Time Out)
Low)
and TM
Top-off
LED = Z
VBAT > 0.175 VCC,
VBAT < 2V, and
VTS > VCC/2
Trickle
LED =
Flash
VBAT > 2V
VBAT
2V
Trickle
LED = Z
VBAT
2V or
VTS
VCC/2 or
Maximum Time Out
SD2002C.eps
Figure 2. State Diagram
Clock
Phase
Generator
OSC
TM
Timing
Control
Sample
History
Voltage
Reference
PVD, - V
ALU
A to D
Converter
INH
Charge-Control
State Machine
LBAT
Check
HTF TCO
Check Check
Power-On
Reset
CC
LED
TS
Power
Down
VCC
MCV
Check
BAT
VSS
Bd2002CEG.eps
Figure 3. Block Diagram
3
bq2002E/G
VCC = 0
Fast Charging
Top-Off
(optional)
See Table 1
73ms
CC Output
Fast Charging
Pulse-Trickle
1.17s
1.17s
Charge initiated by application of power
Charge initiated by battery replacement
LED
TD2002EG.eps
Figure 4. Charge Cycle Phases
A ground-referenced negative temperature coefficient thermistor placed near the battery may be used as a low-cost
temperature-to-voltage transducer. The temperature
sense voltage input at TS is developed using a resistorthermistor network between VCC and VSS. See Figure 1.
1. Application of power to VCC or
Starting A Charge Cycle
If the battery is within the configured temperature and
voltage limits, the IC begins fast charge. The valid battery voltage range is VLBAT < VBAT < VMCV, where
2. Voltage at the BAT pin falling through the maximum
cell voltage VMCV where
VMCV = 2V ±5%.
Either of two events starts a charge cycle (see Figure 4):
Table 1. Fast-Charge Safety Time/Hold-Off/Top-Off Table
Typical FastCharge and
Top-Off
Time Limits
(minutes)
Top-Off
Rate
PulseTrickle
Rate
PulseTrickle
Width
(ms)
Maximum
Synchronized
Sampling
Period
(seconds)
300
Disabled
C/32
73
18.7
80
150
C/16
C/32
37
18.7
40
75
Disabled
C/32
18
9.4
Typical PVD
and -∆V
Hold-Off Time
bq2002E bq2002G
(seconds)
Corresponding
Fast-Charge
Rate
TM
Termination
C/2
Mid
PVD
200
160
1C
Low
PVD
80
2C
High
-∆V
40
Notes:
Typical conditions = 25°C, VCC = 5.0V
Mid = 0.5 * VCC ± 0.5V
Tolerance on all timing is ± 12%.
4
bq2002E/G
VLBAT = 0.175 ∗ VCC ±20%
The response of the IC to pulses less than 100ns in
width or between 3.5ms and 12ms is indeterminate. Tolerance on all timing is ±12%.
The valid temperature range is VTS > VHTF where
VHTF = 0.6 ∗ VCC ±5%.
Voltage Termination Hold-off
If the battery voltage or temperature is outside of these
limits, the IC pulse-trickle charges until the next new
charge cycle begins.
A hold-off period occurs at the start of fast charging.
During the hold-off time, the PVD and -∆V terminations
are disabled. This avoids premature termination on the
voltage spikes sometimes produced by older batteries
when fast-charge current is first applied. Maximum
voltage and temperature terminations are not affected
by the hold-off period.
If VMCV < VBAT < VPD (see “Low-Power Mode”) when a
new battery is inserted, a delay of 0.35 to 0.9s is imposed
before the new charge cycle begins.
Fast charge continues until termination by one or more of
the five possible termination conditions:
n
Peak voltage detection (PVD)
n
Negative delta voltage (-∆V)
n
Maximum voltage
n
Maximum temperature
n
Maximum time
Maximum Voltage, Temperature, and Time
Any time the voltage on the BAT pin exceeds the maximum cell voltage,VMCV, fast charge or optional top-off
charge is terminated.
Maximum temperature termination occurs anytime the
voltage on the TS pin falls below the temperature cut-off
threshold VTCO where
VTCO = 0.5 ∗ VCC ± 5%.
PVD and -∆V Termination
Maximum charge time is configured using the TM pin.
Time settings are available for corresponding charge
rates of C/2, 1C, and 2C. Maximum time-out termination is enforced on the fast-charge phase, then reset, and
enforced again on the top-off phase, if selected. There is
no time limit on the trickle-charge phase.
There are two modes for voltage termination, depending
on the state of TM. For -∆V (TM = high), if VBAT is lower
than any previously measured value by 12mV ±3mV, fast
charge is terminated. For PVD (TM = low or mid), a decrease of 2.5mV ±2.5mV terminates fast charge. The PVD
and -∆V tests are valid in the range 1V < VBAT < 2V.
Top-off Charge
Synchronized Voltage Sampling
An optional top-off charge phase may be selected to
follow fast charge termination for 1C and C/2 rates.
This phase may be necessary on NiMH or other battery chemistries that have a tendency to terminate
charge before reaching full capacity. With top-off enabled, ch arging continues a t a r educed r ate after
fast-charge termination for a period of time selected
by the TM pin. (See Table 1.) During top-off, the CC
pin is modulated at a duty cycle of 73ms active for
every 1097ms inactive. This modulation results in an
average rate 1/16th that of the fast charge rate. Maximum voltage, time, and temperature are the only termination methods enabled during top-off.
Voltage sampling at the BAT pin for PVD and -∆V termination may be synchronized to an external stimulus using the INH input. Low-high-low input pulses between
100ns and 3.5ms in width must be applied at the INH
pin with a frequency greater than the “maximum synchronized sampling period” set by the state of the TM
pin as shown in Table 1. Voltage is sampled on the falling edge of such pulses.
If the time between pulses is greater than the synchronizing period, voltage sampling “free-runs” at once every
17 seconds. A sample is taken by averaging together
voltage measurements taken 57µs apart. The IC takes
32 measurements in PVD mode and 16 measurements
in -∆V mode. The resulting sample periods (9.17 and
18.18ms, respectively) filter out harmonics centered
around 55 and 109Hz. This technique minimizes the effect of any AC line ripple that may feed through the
power supply from either 50 or 60Hz AC sources.
Pulse-Trickle Charge
Pulse-trickle is used to compensate for self-discharge
while the battery is idle in the charger. The battery is
pulse-trickle charged by driving the CC pin active once
every 1.17s for the period specified in Table 1. This results in a trickle rate of C/32.
If the INH input remains high for more than 12ms, the
voltage sample history kept by the IC and used for PVD
and -∆V termination decisions is erased and a new history is started. Such a reset is required when transitioning from free-running to synchronized voltage sampling.
TM Pin
The TM pin is a three-level pin used to select the
charge timer, top-off, voltage termination mode, trickle
5
bq2002E/G
rate, and voltage hold-off period options. Table 1 describes the states selected by the TM pin. The midlevel selection input is developed by a resistor divider between VCC and ground that fixes the voltage
on TM at VCC/2 ± 0.5V. See Figure 4.
Low-Power Mode
Charge Status Indication
Both the CC pin and the LED pin are driven to the
high-Z state. The operating current is reduced to less
than 1µA in this mode. When VBAT returns to a value
below VPD, the IC pulse-trickle charges until the next
new charge cycle begins.
The IC enters a low-power state when VBAT is driven
above the power-down threshold (VPD) where
VPD = VCC - (1V ±0.5V)
A fast charge in progress is uniquely indicated when the
LED pin goes low. The LED pin is driven to the high-Z
state for all conditions other than fast charge. Figure 2
outlines the state of the LED pin during charge.
Charge Inhibit
Fast charge and top-off may be inhibited by using the
INH pin. When high, INH suspends all fast charge and
top-off activity and the internal charge timer. INH
freezes the current state of LED until inhibit is removed.
Temperature monitoring is not affected by the INH pin.
During charge inhibit, the bq2002E/G continues to
pulse-trickle charge the battery per the TM selection.
When INH returns low, charge control and the charge
timer resume from the point where INH became active.
6
bq2002E/G
Absolute Maximum Ratings
Symbol
Parameter
Minimum
Maximum
Unit
VCC
VCC relative to VSS
-0.3
+7.0
V
VT
DC voltage applied on any pin
excluding VCC relative to VSS
-0.3
+7.0
V
TOPR
Operating ambient temperature
TSTG
Storage temperature
TSOLDER
Soldering temperature
TBIAS
Temperature under bias
Note:
+70
°C
+85
°C
-
+260
°C
-40
+85
°C
Commercial
10 sec max.
Permanent device damage may occur if Absolute Maximum Ratings are exceeded. Functional operation should be limited to the Recommended DC Operating Conditions detailed in this data sheet. Exposure to conditions beyond the operational limits for extended periods of time may affect device reliability.
DC Thresholds
Symbol
0
-40
Notes
(TA = 0 to 70°C; VCC ± 20%)
Parameter
Rating
Tolerance
Unit
Notes
VTCO
Temperature cutoff
0.5 * VCC
± 5%
V
VTS ≤ VTCO inhibits/terminates
fast charge and top-off
VHTF
High temperature fault
0.6 ∗ VCC
±5%
V
VTS < VHTF inhibits fast charge
start
VMCV
Maximum cell voltage
2
± 5%
V
VBAT ≥ VMCV inhibits/terminates
fast charge and top-off
VLBAT
Minimum cell voltage
0.175 ∗ VCC
±20%
V
VBAT < VLBAT inhibits fast charge
start
-∆V
BAT input change for
-∆V detection
-12
±3
mV
PVD
BAT input change for
PVD detection
-2.5
±2.5
mV
7
bq2002E/G
Recommended DC Operating Conditions (TA = 0 to 70°C)
Symbol
Condition
Minimum
Typical
Maximum
Unit
4.0
5.0
6.0
V
Notes
VCC
Supply voltage
VDET
-∆V, PVD detect voltage
1
-
2
V
VBAT
Battery input
0
-
VCC
V
VTS
Thermistor input
0.5
-
VCC
V
VTS < 0.5V prohibited
VIH
Logic input high
0.5
-
-
V
INH
Logic input high
VCC - 0.5
-
-
V
TM
Logic input mid
VCC
-
+ 0.5
V
TM
VIM
2
VIL
- 0.5
VCC
2
Logic input low
-
-
0.1
V
INH
Logic input low
-
-
0.5
V
TM
VOL
Logic output low
-
-
0.8
V
LED, CC, IOL = 10mA
VPD
Power down
VCC - 1.5
-
VCC - 0.5
V
VBAT ≥ VPD max. powers
down bq2002E/G;
VBAT < VPD min. =
normal operation.
ICC
Supply current
-
-
500
µA
Outputs unloaded,
VCC = 5.1V
I SB
Standby current
-
-
1
µA
VCC = 5.1V, VBAT = VPD
I OL
LED, CC sink
10
-
-
mA
@VOL = VSS + 0.8V
IL
Input leakage
-
-
±1
µA
INH, CC, V = VSS to VCC
I OZ
Output leakage in
high-Z state
-5
-
-
µA
LED, CC
Note:
All voltages relative to VSS.
8
bq2002E/G
Impedance
Symbol
Parameter
Minimum
Typical
Maximum
Unit
RBAT
Battery input impedance
50
-
-
MΩ
RTS
TS input impedance
50
-
-
MΩ
Timing
Symbol
(TA = 0 to +70°C; VCC ± 10%)
Parameter
Minimum
Typical
Maximum
Unit
dFCV
Time base variation
-12
-
12
%
t DLY
Start-up delay
0.35
-
0.9
s
Note:
Typical is at TA = 25°C, VCC = 5.0V.
9
Notes
Starting from VMCV < VBAT < VPD
bq2002E/G
8-Pin DIP (PN)
8-Pin PN (0.300" DIP)
Inches
Min.
Max.
Min.
Max.
A
0.160
0.180
4.06
4.57
A1
0.015
0.040
0.38
1.02
B
0.015
0.022
0.38
0.56
B1
0.055
0.065
1.40
1.65
C
0.008
0.013
0.20
0.33
D
0.350
0.380
8.89
9.65
E
0.300
0.325
7.62
8.26
E1
0.230
0.280
5.84
7.11
D
E1
E
A
B1
A1
L
C
B
S
e
Millimeters
Dimension
e
0.300
0.370
7.62
9.40
G
0.090
0.110
2.29
2.79
L
0.115
0.150
2.92
3.81
S
0.020
0.040
0.51
1.02
G
8-Pin SOIC Narrow (SN)
8-Pin SN (0.150" SOIC)
Inches
10
Millimeters
Dimension
Min.
Max.
Min.
Max.
A
0.060
0.070
1.52
1.78
A1
0.004
0.010
0.10
0.25
B
0.013
0.020
0.33
0.51
C
0.007
0.010
0.18
0.25
D
0.185
0.200
4.70
5.08
E
0.150
0.160
3.81
4.06
e
0.045
0.055
1.14
1.40
H
0.225
0.245
5.72
6.22
L
0.015
0.035
0.38
0.89
PACKAGE OPTION ADDENDUM
www.ti.com
7-May-2007
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
BQ2002EPN
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
BQ2002EPNE4
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
BQ2002ESN
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
BQ2002ESNG4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
BQ2002ESNTR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
BQ2002ESNTRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
BQ2002GPN
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
BQ2002GPNE4
ACTIVE
PDIP
P
8
50
Pb-Free
(RoHS)
CU NIPDAU
N / A for Pkg Type
BQ2002GSN
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
BQ2002GSNG4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
BQ2002GSNTR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
BQ2002GSNTRG4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
7-May-2007
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
19-Mar-2008
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
Diameter Width
(mm) W1 (mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
BQ2002ESNTR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
BQ2002GSNTR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
19-Mar-2008
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
BQ2002ESNTR
SOIC
D
8
2500
340.5
338.1
20.6
BQ2002GSNTR
SOIC
D
8
2500
340.5
338.1
20.6
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2008, Texas Instruments Incorporated
Similar pages