PHILIPS ACT108-600D Ac thyristor power switch Datasheet

TO
-92
ACT108-600D
AC Thyristor power switch
20 August 2014
Product data sheet
1. General description
AC Thyristor power switch in a SOT54 plastic package with self-protective capabilities
against low and high energy transients
2. Features and benefits
•
•
•
•
•
•
•
Exclusive negative gate triggering
Full cycle AC conduction
High noise immunity
Remote gate separates the gate driver from the effects of the load current
Very sensitive gate for lowest gate trigger current
Safe clamping of low energy over-voltage transients
Self-protective turn-on during high energy voltage transients
3. Applications
•
•
•
Fan motor circuits
Pump motor circuits
Lower-power highly inductive, resistive and safety loads
4. Quick reference data
Table 1.
Quick reference data
Symbol
Parameter
VDRM
Conditions
Min
Typ
Max
Unit
repetitive peak offstate voltage
-
-
600
V
ITSM
non-repetitive peak on- full sine wave; Tj(init) = 25 °C;
state current
tp = 20 ms; Fig. 2; Fig. 3
-
-
8
A
IT(RMS)
RMS on-state current
full sine wave; Tlead ≤ 71 °C; Fig. 1
-
-
0.8
A
VPP
peak pulse voltage
Tj = 25 °C; non-repetitive, off-state;
-
-
2
kV
0.5
-
5
mA
0.5
-
5
mA
650
-
-
V
Fig. 4
Static characteristics
IGT
gate trigger current
VD = 12 V; IT = 100 mA; LD+ G-;
Tj = 25 °C; Fig. 6
VD = 12 V; IT = 100 mA; LD- G-;
Tj = 25 °C; Fig. 6
VCL
clamping voltage
ICL = 0.1 mA; tp = 1 ms; Tj ≤ 125 °C
Scan or click this QR code to view the latest information for this product
ACT108-600D
NXP Semiconductors
AC Thyristor power switch
5. Pinning information
Table 2.
Pinning information
Pin
Symbol Description
1
CM
common
2
G
gate
3
LD
load
Simplified outline
Graphic symbol
LD
G
CM
321
001aaj924
TO-92 (SOT54)
6. Ordering information
Table 3.
Ordering information
Type number
Package
Name
Description
Version
ACT108-600D
TO-92
plastic single-ended leaded (through hole) package; 3 leads
SOT54
ACT108-600D/DG
TO-92
plastic single-ended leaded (through hole) package; 3 leads
SOT54
ACT108-600D
Product data sheet
All information provided in this document is subject to legal disclaimers.
20 August 2014
© NXP Semiconductors N.V. 2014. All rights reserved
2 / 12
ACT108-600D
NXP Semiconductors
AC Thyristor power switch
7. Limiting values
Table 4.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).
Symbol
Parameter
Conditions
VDRM
repetitive peak off-state voltage
IT(RMS)
RMS on-state current
ITSM
non-repetitive peak on-state
current
Min
Max
Unit
-
600
V
full sine wave; Tlead ≤ 71 °C; Fig. 1
-
0.8
A
full sine wave; Tj(init) = 25 °C;
-
8.8
A
-
8
A
tp = 16.7 ms
full sine wave; Tj(init) = 25 °C;
tp = 20 ms; Fig. 2; Fig. 3
I t
I2t for fusing
tp = 10 ms; SIN
-
0.32
A s
dIT/dt
rate of rise of on-state current
IT = 1 A; IG = 10 mA; dIG/dt = 0.2 A/µs
-
50
A/µs
IGM
peak gate current
t = 20 μs
-
1
A
VGM
peak gate voltage
-
15
V
PG(AV)
average gate power
-
0.1
W
Tstg
storage temperature
-40
150
°C
Tj
junction temperature
-
125
°C
VPP
peak pulse voltage
-
2
kV
2
over any 20 ms period
Tj = 25 °C; non-repetitive, off-state;
2
Fig. 4
003aac803
1.0
Ptot
(W)
α = 180°
α
0.8
α
0.6
0.4
0.2
0
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
IT(RMS) (A)
0.8
α = conduction angle
Fig. 1.
Total power dissipation as a function of RMS on-state current; maximum values
ACT108-600D
Product data sheet
All information provided in this document is subject to legal disclaimers.
20 August 2014
© NXP Semiconductors N.V. 2014. All rights reserved
3 / 12
ACT108-600D
NXP Semiconductors
AC Thyristor power switch
003aac804
10
ITSM
(A)
8
6
4
ITSM
IT
t
2
1/f
Tj(init) = 25 °C max
0
1
102
10
103
number of cycles
f = 50 Hz
Fig. 2.
Non-repetitive peak on-state current as a function of the number of sinusoidal current cycles; maximum
values
003aac805
103
ITSM
IT
ITSM
(A)
t
tp
102
Tj(init) = 25 °C max
10
1
10- 5
10- 4
10- 3
tp (s)
10- 2
tp ≤ 20 ms
Fig. 3.
Non-repetitive peak on-state current as a function of pulse width; maximum values
IEC 61000-4-5 Standards
Surge Generator
Open Circuit Voltage
1.2 µs/50 µs waveform
RGen
2Ω
Surge pulse
R
L
150 Ω
5 µH
Load Model
RG
DUT
220 Ω
003aad077
Fig. 4.
Test circuit for inductive and resistive loads with conditions equivalent to IEC 61000-4-5
ACT108-600D
Product data sheet
All information provided in this document is subject to legal disclaimers.
20 August 2014
© NXP Semiconductors N.V. 2014. All rights reserved
4 / 12
ACT108-600D
NXP Semiconductors
AC Thyristor power switch
8. Thermal characteristics
Table 5.
Thermal characteristics
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
Rth(j-lead)
thermal resistance
from junction to lead
full cycle with heatsink compound;
Fig. 5
-
-
60
K/W
Rth(j-a)
thermal resistance
from junction to
ambient
full cycle; printed-circuit board
mounted; lead length 4 mm
-
150
-
K/W
003aad294
102
Zth(j-lead)
(K/W)
10
1
P
10- 1
tp
10- 2
10- 5
Fig. 5.
10- 4
10- 3
10- 2
10- 1
1
tp (s)
t
10
Transient thermal impedance from junction to lead as a function of pulse width
ACT108-600D
Product data sheet
All information provided in this document is subject to legal disclaimers.
20 August 2014
© NXP Semiconductors N.V. 2014. All rights reserved
5 / 12
ACT108-600D
NXP Semiconductors
AC Thyristor power switch
9. Characteristics
Table 6.
Characteristics
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
VD = 12 V; IT = 100 mA; LD+ G-;
0.5
-
5
mA
0.5
-
5
mA
-
-
25
mA
-
-
25
mA
Static characteristics
IGT
gate trigger current
Tj = 25 °C; Fig. 6
VD = 12 V; IT = 100 mA; LD- G-;
Tj = 25 °C; Fig. 6
IL
latching current
VD = 12 V; IG = 100 mA; LD+ G-;
Tj = 25 °C; Fig. 7
VD = 12 V; IG = 100 mA; LD- G-;
Tj = 25 °C; Fig. 7
IH
holding current
VD = 12 V; Tj = 25 °C; Fig. 8
-
-
20
mA
VT
on-state voltage
IT = 1.1 A; Tj = 25 °C; Fig. 9
-
-
1.3
V
VGT
gate trigger voltage
VD = 400 V; IT = 100 mA; Tj = 125 °C
0.15
-
-
V
VD = 12 V; IT = 100 mA; Tj = 25 °C
-
-
0.9
V
VD = 600 V; Tj = 25 °C
-
-
2
µA
VD = 600 V; Tj = 125 °C
-
-
0.2
mA
ICL = 0.1 mA; tp = 1 ms; Tj ≤ 125 °C
650
-
-
V
VDM = 402 V; Tj = 125 °C; (VDM = 67%
300
-
-
V/µs
0.15
-
-
A/ms
ID
VCL
off-state current
clamping voltage
Dynamic charateristics
dVD/dt
rate of rise of off-state
voltage
of VDRM); exponential waveform; gate
open circuit; Fig. 10
dIcom/dt
rate of change of
commutating current
VD = 400 V; Tj = 125 °C; IT(RMS) 1 A;
dVcom/dt = 15 V/µs; gate open circuit;
Fig. 11; Fig. 12
ACT108-600D
Product data sheet
All information provided in this document is subject to legal disclaimers.
20 August 2014
© NXP Semiconductors N.V. 2014. All rights reserved
6 / 12
ACT108-600D
NXP Semiconductors
AC Thyristor power switch
003aac809
3
IGT
IGT(25°C)
2
003aac811
3
IL
IL(25°C)
(1)
2
(2)
1
1
(2)
(1)
0
- 50
50
0
100
Tj (°C)
(1) LD+ G(2) LD- GFig. 6.
0
- 50
150
Fig. 7.
003aac810
50
100
Tj (°C)
150
Normalized latching current as a function of
junction temperature
Normalized gate trigger current as a function of
junction temperature
3
0
003aaf722
2.0
IT
(A)
IH
IH(25°C)
1.5
2
1.0
(1)
1
(2)
(3)
0.5
0
- 50
Fig. 8.
0
50
100
Tj (°C)
0.0
0.0
150
0.5
1.0
1.5
VT (V)
2.0
Vo = 0.758 V; Rs = 0.263 Ω
Normalized holding current as a function of
junction temperature
(1) Tj = 125 °C; typical values
(2) Tj = 125 °C; maximum values
(3) Tj = 25 °C; maximum values
Fig. 9.
ACT108-600D
Product data sheet
On-state current as a function of on-state
voltage
All information provided in this document is subject to legal disclaimers.
20 August 2014
© NXP Semiconductors N.V. 2014. All rights reserved
7 / 12
ACT108-600D
NXP Semiconductors
AC Thyristor power switch
A
B
003aac813
12
003aac814
12
A
B
10
8
8
6
4
4
2
0
25
50
75
100
Tj (°C)
0
125
25
50
75
100
Tj (°C)
A = dVD/dt at condition Tj °C
A = dIcom/dt at condition Tj °C
B = dVD/dt at condition Tj [125] °C
B = dIcom/dt at condition Tj [125] °C
Fig. 10. Normalized rate of rise of off-state voltage as a
function of junction temperature
125
VD = 400 V
Fig. 11. Normalized critical rate of rise of commutating
current as a function of junction temperature
003aac815
2.0
A [B]
A [spec]
1.5
1.0
0.5
0
10- 1
1
10
B (V/µs)
102
A [B] = dIcom/dt at condition B, dVcom/dt
A [spec] is the data sheet value for dIcom/dt
turn-off time is less than 20 ms
Fig. 12. Normalized critical rate of change of commutating current as a function of critical rate of change of
commutating voltage; minimum values
ACT108-600D
Product data sheet
All information provided in this document is subject to legal disclaimers.
20 August 2014
© NXP Semiconductors N.V. 2014. All rights reserved
8 / 12
ACT108-600D
NXP Semiconductors
AC Thyristor power switch
10. Package outline
Plastic single-ended leaded (through hole) package; 3 leads
SOT54
c
E
d
A
L
b
1
e1
2
D
e
3
b1
L1
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
b
b1
c
D
d
E
e
e1
L
L1(1)
mm
5.2
5.0
0.48
0.40
0.66
0.55
0.45
0.38
4.8
4.4
1.7
1.4
4.2
3.6
2.54
1.27
14.5
12.7
2.5
max.
Note
1. Terminal dimensions within this zone are uncontrolled to allow for flow of plastic and terminal irregularities.
OUTLINE
VERSION
SOT54
REFERENCES
IEC
JEDEC
JEITA
TO-92
SC-43A
EUROPEAN
PROJECTION
ISSUE DATE
04-06-28
04-11-16
Fig. 13. Package outline TO-92 (SOT54)
ACT108-600D
Product data sheet
All information provided in this document is subject to legal disclaimers.
20 August 2014
© NXP Semiconductors N.V. 2014. All rights reserved
9 / 12
ACT108-600D
NXP Semiconductors
AC Thyristor power switch
In no event shall NXP Semiconductors be liable for any indirect, incidental,
punitive, special or consequential damages (including - without limitation lost profits, lost savings, business interruption, costs related to the removal
or replacement of any products or rework charges) whether or not such
damages are based on tort (including negligence), warranty, breach of
contract or any other legal theory.
11. Legal information
11.1 Data sheet status
Notwithstanding any damages that customer might incur for any reason
whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards
customer for the products described herein shall be limited in accordance
with the Terms and conditions of commercial sale of NXP Semiconductors.
Document
status [1][2]
Product
status [3]
Objective
[short] data
sheet
Development This document contains data from
the objective specification for product
development.
Preliminary
[short] data
sheet
Qualification
This document contains data from the
preliminary specification.
Product
[short] data
sheet
Production
This document contains the product
specification.
[1]
[2]
[3]
Definition
Right to make changes — NXP Semiconductors reserves the right to
make changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
Please consult the most recently issued document before initiating or
completing a design.
The term 'short data sheet' is explained in section "Definitions".
The product status of device(s) described in this document may have
changed since this document was published and may differ in case of
multiple devices. The latest product status information is available on
the Internet at URL http://www.nxp.com.
11.2 Definitions
Preview — The document is a preview version only. The document is still
subject to formal approval, which may result in modifications or additions.
NXP Semiconductors does not give any representations or warranties as to
the accuracy or completeness of information included herein and shall have
no liability for the consequences of use of such information.
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences
of use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is
intended for quick reference only and should not be relied upon to contain
detailed and full information. For detailed and full information see the
relevant full data sheet, which is available on request via the local NXP
Semiconductors sales office. In case of any inconsistency or conflict with the
short data sheet, the full data sheet shall prevail.
Product specification — The information and data provided in a Product
data sheet shall define the specification of the product as agreed between
NXP Semiconductors and its customer, unless NXP Semiconductors and
customer have explicitly agreed otherwise in writing. In no event however,
shall an agreement be valid in which the NXP Semiconductors product
is deemed to offer functions and qualities beyond those described in the
Product data sheet.
11.3 Disclaimers
Limited warranty and liability — Information in this document is believed
to be accurate and reliable. However, NXP Semiconductors does not give
any representations or warranties, expressed or implied, as to the accuracy
or completeness of such information and shall have no liability for the
consequences of use of such information. NXP Semiconductors takes no
responsibility for the content in this document if provided by an information
source outside of NXP Semiconductors.
ACT108-600D
Product data sheet
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in life support, life-critical or
safety-critical systems or equipment, nor in applications where failure or
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors and its suppliers accept no liability for
inclusion and/or use of NXP Semiconductors products in such equipment or
applications and therefore such inclusion and/or use is at the customer’s own
risk.
Quick reference data — The Quick reference data is an extract of the
product data given in the Limiting values and Characteristics sections of this
document, and as such is not complete, exhaustive or legally binding.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and operation of their
applications and products using NXP Semiconductors products, and NXP
Semiconductors accepts no liability for any assistance with applications or
customer product design. It is customer’s sole responsibility to determine
whether the NXP Semiconductors product is suitable and fit for the
customer’s applications and products planned, as well as for the planned
application and use of customer’s third party customer(s). Customers should
provide appropriate design and operating safeguards to minimize the risks
associated with their applications and products.
NXP Semiconductors does not accept any liability related to any default,
damage, costs or problem which is based on any weakness or default
in the customer’s applications or products, or the application or use by
customer’s third party customer(s). Customer is responsible for doing all
necessary testing for the customer’s applications and products using NXP
Semiconductors products in order to avoid a default of the applications
and the products or of the application or use by customer’s third party
customer(s). NXP does not accept any liability in this respect.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) will cause permanent
damage to the device. Limiting values are stress ratings only and (proper)
operation of the device at these or any other conditions above those
given in the Recommended operating conditions section (if present) or the
Characteristics sections of this document is not warranted. Constant or
repeated exposure to limiting values will permanently and irreversibly affect
the quality and reliability of the device.
Terms and conditions of commercial sale — NXP Semiconductors
products are sold subject to the general terms and conditions of commercial
sale, as published at http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an individual
agreement is concluded only the terms and conditions of the respective
agreement shall apply. NXP Semiconductors hereby expressly objects to
applying the customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
No offer to sell or license — Nothing in this document may be interpreted
or construed as an offer to sell products that is open for acceptance or the
All information provided in this document is subject to legal disclaimers.
20 August 2014
© NXP Semiconductors N.V. 2014. All rights reserved
10 / 12
ACT108-600D
NXP Semiconductors
AC Thyristor power switch
grant, conveyance or implication of any license under any copyrights, patents
or other industrial or intellectual property rights.
Export control — This document as well as the item(s) described herein
may be subject to export control regulations. Export might require a prior
authorization from competent authorities.
Non-automotive qualified products — Unless this data sheet expressly
states that this specific NXP Semiconductors product is automotive qualified,
the product is not suitable for automotive use. It is neither qualified nor
tested in accordance with automotive testing or application requirements.
NXP Semiconductors accepts no liability for inclusion and/or use of nonautomotive qualified products in automotive equipment or applications.
In the event that customer uses the product for design-in and use in
automotive applications to automotive specifications and standards,
customer (a) shall use the product without NXP Semiconductors’ warranty
of the product for such automotive applications, use and specifications, and
(b) whenever customer uses the product for automotive applications beyond
NXP Semiconductors’ specifications such use shall be solely at customer’s
own risk, and (c) customer fully indemnifies NXP Semiconductors for any
liability, damages or failed product claims resulting from customer design and
use of the product for automotive applications beyond NXP Semiconductors’
standard warranty and NXP Semiconductors’ product specifications.
Translations — A non-English (translated) version of a document is for
reference only. The English version shall prevail in case of any discrepancy
between the translated and English versions.
11.4 Trademarks
Notice: All referenced brands, product names, service names and
trademarks are the property of their respective owners.
Adelante, Bitport, Bitsound, CoolFlux, CoReUse, DESFire, EZ-HV,
FabKey, GreenChip, HiPerSmart, HITAG, I²C-bus logo, ICODE, ICODE, ITEC, Labelution, MIFARE, MIFARE Plus, MIFARE Ultralight,
MoReUse, QLPAK, Silicon Tuner, SiliconMAX, SmartXA, STARplug,
TOPFET, TrenchMOS, TriMedia and UCODE — are trademarks of NXP
Semiconductors N.V.
HD Radio and HD Radio logo — are trademarks of iBiquity Digital
Corporation.
ACT108-600D
Product data sheet
All information provided in this document is subject to legal disclaimers.
20 August 2014
© NXP Semiconductors N.V. 2014. All rights reserved
11 / 12
ACT108-600D
NXP Semiconductors
AC Thyristor power switch
12. Contents
1
General description ............................................... 1
2
Features and benefits ............................................1
3
Applications ........................................................... 1
4
Quick reference data ............................................. 1
5
Pinning information ............................................... 2
6
Ordering information ............................................. 2
7
Limiting values .......................................................3
8
Thermal characteristics .........................................5
9
Characteristics ....................................................... 6
10
Package outline ..................................................... 9
11
11.1
11.2
11.3
11.4
Legal information .................................................10
Data sheet status ............................................... 10
Definitions ...........................................................10
Disclaimers .........................................................10
Trademarks ........................................................ 11
© NXP Semiconductors N.V. 2014. All rights reserved
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
Date of release: 20 August 2014
ACT108-600D
Product data sheet
All information provided in this document is subject to legal disclaimers.
20 August 2014
© NXP Semiconductors N.V. 2014. All rights reserved
12 / 12
Similar pages