TI MC3550 Quad differential line receiver Datasheet

MC3450, MC3452, MC3550, MC3552
QUAD DIFFERENTIAL LINE RECEIVERS
SLLS012B – FEBRUARY 1986 – REVISED FEBRUARY 1993
D
D
D
D
D
D
MC3450, MC3452 . . . D OR N PACKAGE
MC3550, MC3552 . . . J PACKAGE
(TOP VIEW)
Four Independent Receivers With Common
Enable Input
High Input Sensitivity . . . 25 mV Max
High Input Impedance
MC3450 and MC3550 Have 3-State Outputs
MC3452 Has Open-Collector Outputs
Glitch-Free Power-Up/Power-Down
Operation
1B
1A
1Y
EN
2Y
2A
2B
GND
description
The MC3450, MC3550, MC3452, and MC3552
are quad differential line receivers designed for
use in balanced and unbalanced digital data
transmission. The MC34/3550 and MC34/3552
are the same except that the MC3450 and
MC3550 have 3-state outputs whereas the
MC3452 and MC3552 have open-collector
outputs, which permit the wire-AND function with
similar output devices. The 3-state and opencollector outputs permit connection directly to a
bus-organized system.
1
16
2
15
3
14
4
13
5
12
6
11
7
10
8
9
VCC +
4B
4A
4Y
VCC –
3Y
3A
3B
1A
1B
NC
VCC+
4B
MC3550, MC3552 . . . FK PACKAGE
(TOP VIEW)
1Y
EN
NC
2Y
2A
3 2 1 20 19
18
5
17
6
16
7
15
8
14
9 10 11 12 13
4A
4Y
NC
VCC –
3Y
2B
GND
NC
3B
3A
The MC3450, MC3550, MC3452, and MC3550
are designed for optimum performance when
used with either the MC3453 or MC3553 quad
differential line driver or SN75109A, SN75110A,
and SN75112 dual differential drivers.
4
NC – No internal connection
The MC3450 and MC3452 are characterized for
operation from 0°C to 70°C. The MC3550 and
MC3552 are characterized for operation over the
full military temperature range of – 55°C
to 125°C.
THE MC3452 IS NOT
RECOMMENDED FOR NEW DESIGN
FUNCTION TABLE
DIFFERENTIAL INPUTS
ENABLE
OUTPUT
A–B
EN
Y
VID ≥ 25 mV
L
H
– 25 mV < VID < 25 mV
L
?
VID ≤ 25 mV
L
L
X
H
Z
H = high level, L = low level,
X = impedance (off)
? = indeterminate,
Copyright  1993, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
MC3450, MC3452, MC3550, MC3552
QUAD DIFFERENTIAL LINE RECEIVERS
SLLS012B – FEBRUARY 1986 – REVISED FEBRUARY 1993
logic symbols†
MC3452/MC3552
MC3450/MC3550
EN
1A
1B
2A
2B
3A
3B
4A
4B
4
EN
4
EN
2
3
1
6
5
7
10
11
9
14
13
15
1Y
2Y
3Y
4Y
2
1A
1
1B
6
2A
7
2B
10
3A
9
3B
14
4A
15
4B
† These symbols are in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12.
logic diagram (positive logic)
EN
1A
1B
2A
2B
3A
3B
4A
4B
2
4
2
1
6
3
5
7
10
2Y
11
3Y
9
14
15
POST OFFICE BOX 655303
1Y
13
4Y
• DALLAS, TEXAS 75265
EN
3
5
11
13
1Y
2Y
3Y
4Y
MC3450, MC3452, MC3550, MC3552
QUAD DIFFERENTIAL LINE RECEIVERS
SLLS012B – FEBRUARY 1986 – REVISED FEBRUARY 1993
schematics of inputs and outputs
EQUIVALENT OF
A OR B INPUT
EQUIVALENT OF
ENABLE INPUT
TYPICAL OF MC3450
OUTPUT
VCC +
VCC +
1 kΩ
NOM
Input
TYPICAL OF MC3452
OUTPUT
VCC
140 Ω
NOM
3 kΩ
NOM
Output
Input
Output
200 Ω
NOM
VCC –
GND
GND
VCC –
GND
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage, VCC + (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Supply voltage, VCC – . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 7 V
Differential input voltage (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 6 V
Common-mode input voltage (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 5 V
Enable input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Continuous total dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating free-air temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
Case temperature for 60 seconds: FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: D or N package . . . . . . . . . . . . . . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: J package . . . . . . . . . . . . . . . . . . . . . 300°C
NOTES: 1. All voltage values, except differential input voltage, are with respect to network ground terminal.
2. Differential input voltage is measured at the noninverting input with respect to the corresponding inverting input.
3. Common-mode input voltage is the average of the voltages at the A and B inputs.
DISSIPATION RATING TABLE
PACKAGE
TA ≤ 25°C
POWER RATING
OPERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 125°C
POWER RATING
D
950 mW
7.6 mW/°C
608 mW
—
FK
1375 mW
11.0 mW/°C
880 mW
275 mW
J
1375 mW
11.0 mW/°C
880 mW
275 mW
N
1150 mW
9.2 mW/°C
736 mW
—
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
MC3450, MC3452, MC3550, MC3552
QUAD DIFFERENTIAL LINE RECEIVERS
SLLS012B – FEBRUARY 1986 – REVISED FEBRUARY 1993
recommended operating conditions
Supply voltage
voltage, VCC +
TA ≥ 25°C
TA < 25°C
Supply voltage,
voltage VCC –
TA ≥ 25°C
TA < 25°C
High-level enable input voltage, VIH
MIN
NOM
MAX
4.5
5
5.5
4.75
5
5.5
– 4.5
–5
– 5.5
– 4.75
–5
– 5.5
2
Low-level enable input voltage, VIL
Low-level output current, IOL
UNIT
V
V
V
0.8
V
– 16
mA
5
V
Common-mode input voltage, VIC (see Note 4)
–5†
–3†
3
V
Input voltage range, any different input to GND
–5†
3
V
MC3450, MC3452
0
70
MC3550, MC3552
– 55
125
Differential input voltage, VID (see Note 4)
Operating free-air
free air temperature,
temperature TA
°C
† The algebraic convention, in which the less positive (more negative) limit is designated minimum, is used in this data sheet for common-mode
input voltage.
NOTE 4: The recommended combinations of input voltages fall within the shaded area of Figure 1.
RECOMMENDED COMBINATIONS OF INPUT VOLTAGES
Input A to GND Voltage – V
3
2
1
0
–1
–2
–3
–4
–5
1
2
–5 –4 –3 –2 –1 0
Input B to GND Voltage – V
3
Figure 1
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MC3450, MC3452, MC3550, MC3552
QUAD DIFFERENTIAL LINE RECEIVERS
SLLS012B – FEBRUARY 1986 – REVISED FEBRUARY 1993
electrical characteristics over recommended operating free-air temperature range, VCC ± = MAX
(unless otherwise noted)
PARAMETER
VOH
High-level
output voltage
g
g
VOL
Low-level output voltage
g
IOH
High-level output current
A inputs
B inputs
High-level
g
input current
IIH
A inputs
Low-level
L
l
l
in
ut current
input
MIN
VCC ± = ± 4.75 V,
EN at 0.8 V,
VIC = – 3 V to 3 V
VID = 25 mV,
IOH = – 400 µA,
µ
VCC ± = ± 4.75 V,
EN at 2 V,
VIC = – 3 V to 3 V
VCC ± = ± 4.75 V,
VID = –25
25 mV,
IOL = 16 mA,
B inputs
EN
IOZ
High-impedance
g
state
output current
IOS
Short circuit output current‡
Short-circuit
ICCH +
Supply
y current from VCC +,
outputs high
ICCH –
Supply
y current from VCC – ,
outputs high
MC3452, MC3552
TYP†
MAX
MIN
2.4
0.5
VOH = 5.25 V
VID = – 2 V
VID = – 2 V
UNIT
V
0.5
V
250
µA
30
75
30
75
30
75
30
75
µA
40
40
µA
1
1
mA
VID = 2 V
VID = 2 V
– 10
–10
– 10
–10
VIL = 0.4 V
VO = 2.4 V
–1.6
–1.6
VO = 0.4 V
– 40
VIH = 2.4 V
VIH = 5.25 V
EN
IIL
MC3450, MC3550
TYP†
MAX
TEST CONDITIONS
40
VID = 25 mV,
EN at 0.8 V
VO = 0,
A inputs at GND,
EN at 3 V
B inputs at 3 V,
– 18
µA
mA
µA
– 70
mA
60
60
mA
– 30
– 30
mA
MC3450, MC3550
MIN TYP†
MAX
MC3452, MC3552
MIN TYP†
MAX
† All typical values are at VCC + = 5 V, VCC – = – 5 V, TA = 25°C.
‡ Not more than one output should be shorted at a time.
switching characteristics, VCC ± – ± 5 V, TA = 25°C
FROM
TO
(INPUT)
(OUTPUT)
tPLH
A and B
Y
tPHL
A and B
Y
tPZH
tPZL
EN
Y
EN
Y
tPHZ
tPLZ
EN
Y
EN
Y
tPLH
tPHL
EN
EN
PARAMETER
TEST CONDITIONS
17
CL = 50 pF,
See Figure 2
CL = 15 pF,
See Figure 2
CL = 50 pF,
See Figure 2
CL = 15 pF,
See Figure 2
CL = 50 pF,
pF
See Figure 2
CL = 15 pF,
pF
See Figure 3
Y
CL = 15 pF,
See Figure 4
25
ns
Y
CL = 15 pF,
See Figure 4
25
ns
17
25
UNIT
19
25
19
25
25
21
ns
ns
ns
27
18
ns
29
† All typical values are at VCC + = 5 V, VCC – = – 5 V, TA = 25°C.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
MC3450, MC3452, MC3550, MC3552
QUAD DIFFERENTIAL LINE RECEIVERS
SLLS012B – FEBRUARY 1986 – REVISED FEBRUARY 1993
PARAMETER MEASUREMENT INFORMATION
Output
5V
390 Ω
Generator
(see Note A)
5V
390 Ω
50 Ω
For MC3452
or MC3552
100 mV
CL
(see Note B)
For MC3450 or MC3552
(see Note C)
TEST CIRCUIT
200 mV
Input
100 mV
100 mV
0V
tPLH
tPHL
VOH
1.5 V
1.5 V
Output
VOL
VOLTAGE WAVEFORMS
NOTES: A. The input pulse is supplied by a generator having the following characteristics: PRR ≤ 1 MHz, duty cycle = 50%, tr ≤ 6 ns,
tf ≤ 6 ns.
B. CL includes probe and jig capacitance.
C. All diodes are 1N916 or equivalent.
Figure 2. Test Circuit and Voltage Waveforms
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MC3450, MC3452, MC3550, MC3552
QUAD DIFFERENTIAL LINE RECEIVERS
SLLS012B – FEBRUARY 1986 – REVISED FEBRUARY 1993
PARAMETER MEASUREMENT INFORMATION
A
B
S1
S2
tPZH
tPZL
100 mV
GND
Open
Closed
GND
100 mV
Closed
Open
tPHZ
tPLZ
100 mV
GND
Closed
Closed
GND
100 mV
Closed
Closed
Output
A
390 Ω
5V
B
(see Note C)
1 kΩ
Generator
(see Note A)
S1
CL
(see Note B)
50 Ω
S2
TEST CIRCUIT
3V
EN
3V
EN
1.5 V
1.5 V
0V
0V
tPZL
tPZH
VOH
Output
Output
1.5 V
1.5 V
0V
VOL
3V
3V
1.5 V
EN
5V
EN
0V
0V
tPHZ
tPLZ
≈ 1.5 V
VOH
Output
VOH – 0.5 V
Output
VOL + 0.5 V
≈ 1.5 V
VOL
VOLTAGE WAVEFORMS
NOTES: A. The input pulse is supplied by a generator having the following characteristics: PRR ≤ 1 MHz, duty cycle = 50%, tr ≤ 6 ns, tf ≤ 6 ns.
B. CL includes probe and jig capacitance.
C. All diodes are 1N916 or equivalent.
Figure 3. MC3450 and MC3550 Test Circuit and Voltage Waveforms
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
MC3450, MC3452, MC3550, MC3552
QUAD DIFFERENTIAL LINE RECEIVERS
SLLS012B – FEBRUARY 1986 – REVISED FEBRUARY 1993
PARAMETER MEASUREMENT INFORMATION
5V
390 Ω
–100 mV
Output
CL
(see Note B)
Generator
(see Note A)
50 Ω
TEST CIRCUIT
3V
EN
1.5 V
1.5 V
0V
tPLH
tPHL
VOH
1.5 V
1.5 V
Output
VOL
VOLTAGE WAVEFORMS
NOTES: A. The input pulse is supplied by a generator having the following characteristics: PRR ≤ 1 MHz, duty cycle = 50%, tr ≤ 6 ns, tf ≤ 6 ns.
B. CL includes probe and jig capacitance.
Figure 4. MC3452 and MC3552 Test Circuit and Voltage Waveforms
8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments (TI) reserves the right to make changes to its products or to discontinue any semiconductor
product or service without notice, and advises its customers to obtain the latest version of relevant information
to verify, before placing orders, that the information being relied on is current and complete.
TI warrants performance of its semiconductor products and related software to the specifications applicable at
the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are
utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each
device is not necessarily performed, except those mandated by government requirements.
Certain applications using semiconductor products may involve potential risks of death, personal injury, or
severe property or environmental damage (“Critical Applications”).
TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORIZED, OR WARRANTED
TO BE SUITABLE FOR USE IN LIFE-SUPPORT APPLICATIONS, DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS.
Inclusion of TI products in such applications is understood to be fully at the risk of the customer. Use of TI
products in such applications requires the written approval of an appropriate TI officer. Questions concerning
potential risk applications should be directed to TI through a local SC sales office.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards should be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance, customer product design, software performance, or
infringement of patents or services described herein. Nor does TI warrant or represent that any license, either
express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property
right of TI covering or relating to any combination, machine, or process in which such semiconductor products
or services might be or are used.
Copyright  1998, Texas Instruments Incorporated
Similar pages