ON LC898214XD-MH Af controller Datasheet

LC898214XD
CMOS LSI
AF Controller
www.onsemi.com
Overview
This LSI is AF control LSI. It consists of 1 system of feedback circuit
for AF control.
Features
 Built-in equalizer circuit using digital operation
- AF control equalize circuit
- Any coefficient can be specified by I2C I/F
WLCSP8, 1.15x2.37, 0.5P
 I2C Interface
 Built-in A/D converter
- Maximum 10-bit
- Input 2 channel
 Built-in D/A converter
- 8-bit
- Output 2-channel (Hall offset, Constant current Bias)
 Built-in Hall Sensor
- Si Hall sensor
 Built-in EEPROM
- 128 byte (8 byte/page)
 Built-in VGA
- Hall Amp
 Built-in OSC
- 48MHz
 Built-in Constant Current Driver
 Package
- WL-CSP 8-pin
- Pb-Free, Halogen Free
 Supply voltage
- VDD (2.6V to 3.6V)
* I2C Bus is a trademark of Philips Corporation.
ORDERING INFORMATION
See detailed ordering and shipping information on page 9 of this data sheet.
© Semiconductor Components Industries, LLC, 2015
January 2015 - Rev. 1
1
Publication Order Number :
LC898214XD/D
LC898214XD
Pin Description
I
INPUT
O
B
OUTPUT
BIDIRECTION
P
TYPE
Power supply,
GND
NC
■ I2C interface
I2CCK
I2CDT
B
B
I2C Clock pin
I2C Data pin
■ Hall interface
HALL
O
Hall amp output
■ Driver interface
OUT1
OUT2
O
O
Actuator output pin
Actuator output pin
■ Power supply pin
VDD
VSS
P
P
Power supply
GND
O
Test pin
NOT CONNECT
■ Test pin
TEST
*Process when pins are not used
PIN TYPE “O” – Ensure that it is set to OPEN.
PIN TYPE “I” – OPEN is inhibited. Ensure that it is connected to the VDD or VSS even when it is unused.
(Please contact ON Semiconductor for more information about selection of VDD or VSS.)
PIN TYPE “B” – If you are unsure about processing method on the pin description of pin layout table,
please contact us.
Note that incorrect processing of unused pins may result in defects.
www.onsemi.com
2
LC898214XD
Pin Layout
Circuit Name
Analog
Logic
Number of Pins
4
2
Circuit Name
Driver
Number of Pins
2
Backside pin layout diagram (Top View from the mold side)
4
TEST
HALL
3
I2CDT
I2CCK
2
VSS
VDD
1
OUT2
OUT1
A
B
Block Diagram
I2CDT
I2CCK
I2C I/F
VDD
EEPROM
DA
+
-
Hall
Driver
VDD
+
-
Constant
Current
Driver
Hall
OUT1
OUT2
VGA
AD
Control
logic
EQ
VDD
Temp
VDD
OSC
POR
LDO
TEST
VSS
HALL
0.01uF
www.onsemi.com
3
LC898214XD
Package Dimensions
unit : mm
WLCSP8, 1.15x2.37, 0.5P
CASE 567KL
ISSUE A
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. COPLANARITY APPLIES TO THE SPHERICAL
CROWNS OF SOLDER BALLS.
A B
E
PIN A1
REFERENCE
D
DIM
A
A1
b
D
E
e
TOP VIEW
0.10 C
A
0.08 C
A1
NOTE 3
C
SIDE VIEW
MILLIMETERS
MIN
MAX
0.33
0.27
0.04 REF
0.12
0.22
1.12
1.18
2.34
2.40
0.50 BSC
RECOMMENDED
SOLDERING FOOTPRINT*
SEATING
PLANE
PACKAGE
OUTLINE
A1
0.50
PITCH
e/2
e/2
e
e
8X
0.17
B
0.50
PITCH
A
1
2
3
4
BOTTOM VIEW
8X
b
0.05 C A B
0.03 C
DIMENSIONS: MILLIMETERS
*For additional information on our Pb-Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
www.onsemi.com
4
LC898214XD
Electrical Characteristics
1) Absolute maximum rating at VSS = 0V
Item
Symbol
Condition
Rating
Unit
Supply voltage
VDD33 max
Ta ≤25°C
0.3 to 4.6
V
Input/output voltage
VI33,VO33
Ta ≤25°C
0.3 to VDD33+0.3
V
55 to 125
°C
Storage ambient temperature
Tstg
Operating ambient temperature
Topr
Continuous output current
Iomax
30 to 70
°C
150
mA
OUT1,OUT2
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed,
damage may occur and reliability may be affected.
2) Acceptable operation range at Ta = 30 to 70 °C, VSS = 0V
3V power supply (VDD)
Item
Supply voltage
Symbol
Min
Std
VDD33
2.6
2.8
3.6
V
VIN
0
-
VDD33
V
Input voltage range
Max
Unit
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended
Operating Ranges limits may affect device reliability.
3) DC characteristics : Input/output level at VSS = 0V, VDD = 2.6V to 3.6V, Ta = 30 to 70 °C
Item
Symbol
Condition
Min
High-level input voltage
VIH
1.4
Low-level input voltage
VIL
CMOS compliant
Schmidt
Low-level output voltage
VOL
IOL= 2mA
Std
Max
Unit
V
0.4
V
0.4
V
Applicable pins
I2CCK, I2CDT,
I2CDT
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be
indicated by the Electrical Characteristics if operated under different conditions.
4) Driver output (OUT1, OUT2) at VSS = 0V, VDD = 2.8V, Ta = 25 °C
Item
Maximum current
Output ON resistance
Symbol
Condition
Min
Ifull
Ronu
Compliance voltage
Vcomp
Output leak current
Ioleak
Std
108
Io=120mA Pch
Max
Unit
137
mA
2.8
Ω
1
A
0.9
V
0.5
Diode forward voltage
VD
ID=120mA
Actuator resistance (Ract) = (VM-(Ronu*Io+Vcomp)) / Io [Ω]
V
Applicable pins
OUT1, OUT2
5) Non-volatile Memory Characteristics
Item
Symbol
Endurance
EN
Data retention
RT
Condition
Min
10
www.onsemi.com
5
Std
Max
Unit
1000
Cycles
Years
Applicable pins
E2PROM
LC898214XD
Hall element position
Figure 1 : Hall element position
Please refer to package diagram for each dimension.
www.onsemi.com
6
LC898214XD
AC Characteristics
VDD supply timing
Figure 2 : VDD supply timing
It is available to use I2C 2ms later for Power On Reset of VDD.
Item
VDD turn on time
2
Symbol
Min
t1
Typ
Max
Unit
3
ms
I C start time from VDD on
t2
2
ms
VDD off time
t3
10
ms
www.onsemi.com
7
LC898214XD
AC specification
Figure 2 shows interface timing definition and Table 1 shows electric characteristics.
Figure 3 : I2C interface timing definition
Table 1 : Electric characteritics for I2C interface (AC characteristics)
Item
I2CCK clock frequency
START condition
hold time
I2CCK clock
Low period
I2CCK clock
High period
Setup time for repetition
START condition
Pin
name
Symbol
Unit
400
kHz
I2CCK
tHD,STA
0.6
s
tLOW
I2CCK
1.3
s
tHIGH
I2CCK
0.6
s
0.6
s
tSU,STA
Data setup time
tSU,DAT
Bus free time between STOP
and START
Max
I2CCK
I2CDT
tHD,DAT
STOP condition setup time
Typ
Fi2cck
Data hold time
I2CDT, I2CCK
rising time
I2CDT, I2CCK
falling time
Min
tr
tf
tSU,STO
tBUF
I2CCK
I2CDT
I2CCK
I2CDT
I2CCK
I2CDT
I2CCK
I2CDT
I2CCK
I2CDT
I2CCK
I2CDT
I2CCK
I2CDT
0 (*)
0.9
100
s
ns
300
ns
300
ns
0.6
s
1.3
s
* : Although the I2C specification defines a condition that 300 ns of hold time is required internally, LC898214XD is
designed for a condition with typ. 20 ns of hold time. If I2CDT signal is unstable around falling point of I2CCK
signal, please implement an appropriate treatment on board, such as inserting a resistor.
www.onsemi.com
8
LC898214XD
ORDERING INFORMATION
Device
LC898214XD-MH
Package
WLCSP8, 1.15x2.37, 0.5P
(Pb-Free / Halogen Free)
Shipping (Qty / Packing)
5000 / Tape & Reel
ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States
and/or other countries. SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of
SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf . SCILLC reserves the right to make changes without
further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose,
nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including
without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can
and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are
not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or
sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers,
employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was
negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all
applicable copyright laws and is not for resale in any manner.
www.onsemi.com
9
Similar pages