Fujitsu FTR-LYAA048VNIL Power relay 1 pole - 6a slim type (medium load control) Datasheet

FTR-K1 SERIES
POWER RELAY
1 POLE - 6A Slim Type (Medium Load Control)
FTR-LY Series
n FEATURES
Slim 15.0mm (h) x 5.0 mm (w) x 28.0mm (l)
1 form C and right angle type available
2
l Mounting space: 140mm , weight: 5.0g
l High insulation in small package
Insulation distance (between coil and contacts): 8mm
(creepage/clearance)
Dielectric strength: 4,000 VAC
Surge strength: 6,000V
l Plastic sealed type RTIII
l UL, CSA, VDE, SEMKO, FIMKO, DEMKO, NEMKO
compliance
l Socket type available
l RoHS compliant
Please see page 7 for more information
l
l
n
PARTNUMBER INFORMATION
[Example]
(a)
FTR-LY
(a)
A
(b)
Relay type
(b)
Contact configuration
(c)
Coil type
A
(c)
005 Y - SK
(d) (e)
(f )
FTR-LY : FTR-LY-Series
A
C
P
R
: 1 form A
: 1 form C
: 1 form A (right angle type)
: 1 form C (right angle type)
A
: Standard type (170mW)
(d)
Coil rated voltage
005
: 5.....60 VDC
Coil rating table at page 3
(e)
Contact material
E
Y
V
: AgNi
: AgSnO2
: AgSnO2 + Au (0.3µm)
Nil
SK
: PCB mounting type
: Socket mounting type (only contact configuration A and C
(f)
Special type
Actual marking does not carry the type name : "FTR" and "SK"
E.g.: Ordering code: FTR-LYAA005Y-SK Actual marking: LYAA005Y
1
FTR-K1
SERIES
FTR-LY
SERIES
n SPECIFICATION
Item
Contact Data
Life
Coil Data
Timing Data
Insulation
LY (C,R) A ( ) (Y,E,V)
LY (A,P) A ( ) (Y,E,V)
Configuration
1 form C (SPDT)
1 form A (SPST-NO)
Construction
Single
Material
Y: AgSnO2 / E: AgNi / V: AgSnO2 + Au 0.3μm
Resistance (initial)
Y, E: Max. 100 mΩ at 6 VDC, 1 A
V: Max. 30 mΩ at 6 VDC, 1A
Contact rating
6A, 250VAC / 24VDC
Max. carrying current
6A
Max. switching voltage
250VAC
Max. switching power
1,500VA / 144W
Min. switching load *
Y, E: 100 mA 5 VDC
V: 10mA 5 VDC
Mechanical
Min. 10 x 106 operations
Electrical
Min. 50 x 103 operations (N.O.)
Min. 30 x 103 operations (N.C.) at 6A, 250VAC / 30VDC
resistive
Rated power
170 to 217 mW
Operate power
74 to 76 mW
Operating temperature range
-40 °C to +85 °C (no frost)
Operate (at nominal voltage)
Max. 8ms (no diode, without bounce)
Release (at nominal voltage)
Max. 4ms (no diode, without bounce)
Resistance (initial)
Min. 1,000MΩ at 500VDC
Dielectric strength
Surge strength
1,000VAC (50/60Hz) 1min.,10mA detection current
Contacts to coil
4,000VAC (50/60Hz) 1min.,10mA detection current
Coil to contacts
6,000V / 1.2 x 50µs standard wave
Clearance
8 mm
Creepage
8 mm
EN61810-1, VDE0435
Other
Open contacts
Vibration resistance
Shock
Voltage
250V
Pollution degree
3
Material group
III a
Category
C / 250V
Misoperation
10 to 55Hz double amplitude 1.0mm
Endurance
10 to 55Hz double amplitude 1.5mm
Misoperation
Min. 50m/s² (11 ± 1ms)
Endurance
Min. 1,000m/s² (6 ± 1ms)
Weight
Approximately 5 g
Sealing
Plastic sealed RTIII
Min. 100m/s² (11 ± 1ms)
* Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual
load before production since reference values may vary according to switching frequencies, environmental conditions
and expected reliability levels.
2
FTR-K1
SERIES
FTR-LY
SERIES
n COIL RATING
Coil
Code
Rated Coil
Voltage
(VDC)
Coil Resistance
+/- 10% (Ohm)
Must Operate
Voltage
(VDC) *
Must ReleaseVoltage
(VDC) *
Max. Coil Voltage
(VDC)
005
5
147
3.3
0.25
11.5
006
6
211
4
0.3
13.8
009
9
476
5.9
0.45
20.7
012
12
847
7.9
0.6
27.6
018
18
1,910
11.9
0.9
41.4
024
24
3,390
15.9
1.2
55.2
048
48
10,600
31.7
2.4
110.4
217
060
60
20,570
39.6
3
138
175
Rated Power
(mW)
170
Note: All values in the table are valid for 20°C and zero contact current.
* Specified operate values are valid for pulse wave voltage.
n
SAFETY STANDARDS
Type
Compliance
Contact rating
UL
UL 508
Flammability: UL 94-V0 (plastics)
E63614
5A, 277 VAC (resistive)
5A, 30 VDC (resistive)
1/10 HP, 277VAC /125VAC
Pilot duty: D300, C300, R300, B300
CSA
C22.2 No. 14
LR 40304
VDE
40006591
EN 61810-1 (VDE 0435-Part 201)
2004-07
250VAC; 6A / 30VDC; 6A :
- 10K ops. FTR-LY(A;P)A...(E;Y;V) -40 °C to +85 °C
- 5K ops. FTR-LY(C;R)A...(E;Y;V) -40 °C to +85 °C
EN 60730-1 (VDE 0631-Part 1)
250VAC; 6(1,5)A, 30K ops. : FTR-LY(A;P)A...(Y;V) +85 °C
250VAC; 3(1,5)A, 100K ops. : FTR-LY(A;P)A...(Y;V) +85 °C
EN 61984 (VDE 0627)
EN 60335-1 (VDE 0700-Part 1)
-
3
FTR-K1
SERIES
FTR-LY
SERIES
n
CHARACTERISTIC DATA
4
FTR-K1
SERIES
FTR-LY
SERIES
n DIMENSIONS
Straight terminal type
l
Dimensions
l
Schematics
l
PC board mounting
hole layout
(BOTTOM VIEW)
l
Schematics
l
PC board mounting
hole layout
(BOTTOM VIEW)
Right angle type
l
Dimensions
Unit: mm
* This terminal is not applicable for 1 form A type.
5
FTR-K1
SERIES
FTR-LY
SERIES
Socket type
l
Dimensions
l
Schematics
l
PC board mounting
hole layout
(BOTTOM VIEW)
JM-6N
l
Dimensions
l
Schematics
6
FTR-K1
SERIES
FTR-LY
SERIES
RoHS Compliance and Lead Free Information
1. General Information
l
l
l
l
All signal and power relays produced by Fujitsu Components are compliant with RoHS directive 2002/95EC including
amendments.
Cadmium as used in electrical contacts is exempted from the RoHS directives on October 21st, 2005.
(Amendment to Directive 2002/95/EC)
All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info for older date codes
at: http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf
Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified.
This material has been verified to be compatible with PbSn assembly process.
2. Recommended Lead Free Solder Profile
l
Recommended solder Sn-3.0Ag-0.5Cu.
Flow Solder condition:
Pre-heating:
Soldering:
maximum 120˚C
dip within 5 sec. at
260˚C solder bath
Solder by Soldering Iron:
Soldering Iron
Temperature:
Duration:
maximum 360˚C
maximum 3 sec.
We highly recommend that you confirm your actual solder conditions
3. Moisture Sensitivity
l
Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated.
4. Tin Whiskers
l
Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length
whisker was found by our in house test.
7
FTR-K1
SERIES
FTR-LY
SERIES
Fujitsu Components International Headquarter Offices
Japan
Fujitsu Component Limited
Gotanda-Chuo Building
3-5, Higashigotanda 2-chome, Shinagawa-ku
Tokyo 141, Japan
Tel: (81-3) 5449-7010
Fax: (81-3) 5449-2626
Email: [email protected]
Web: www.fcl.fujitsu.com
Europe
Fujitsu Components Europe B.V.
Diamantlaan 25
2132 WV Hoofddorp
Netherlands
Tel: (31-23) 5560910
Fax: (31-23) 5560950
Email: [email protected]
Web: emea.fujitsu.com/components/
North and South America
Fujitsu Components America, Inc.
250 E. Caribbean Drive
Sunnyvale, CA 94089 U.S.A.
Tel: (1-408) 745-4900
Fax: (1-408) 745-4970
Email: [email protected]
Web: http://us.fujitsu.com/components
Asia Pacific
Fujitsu Components Asia Ltd.
102E Pasir Panjang Road
#01-01 Citilink Warehouse Complex
Singapore 118529
Tel: (65) 6375-8560
Fax: (65) 6273-3021
Email: [email protected]
Web: http://www.fujitsu.com/sg/services/micro/components/
©2011 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners.
The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general
information purposes.
The use of the contents, data and information provided in this datasheet is at the users’ own risk.
Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive,
complete and up to date.
Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its
employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related
graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof.
Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability
for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use,
with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness,
usefulness, availability and completeness thereof. Rev. June 08, 2011
8
Similar pages