Finisar FTLX3912M335 High link budget, multi-rate, dwdm xfp optical transceiver Datasheet

Finisar
Product Specification
High Link Budget, Multi-Rate, DWDM XFP
Optical Transceiver
FTLX3912M3xx
PRODUCT FEATURES

Supports 8.5Gb/s* to 11.3Gb/s
bit rates

100GHz channel spacing on the
ITU C-band

Hot-pluggable XFP footprint

RoHS-6 Compliant (lead-free)

Temperature-stabilized 1550nm
EML transmitter

Supports -300ps/nm to +800ps/nm

3.3V and 5V power supplies
required

Point-to-Point & OSNR optimized
versions

Power dissipation < 3.5W

Commercial temperature range:
0°C to 70°C

Reference clock not required
APPLICATIONS

SONET OC-192 IR-2 Transmitter w/APD
SDH STM S-64.2b Transmitter w/APD
SDH STM S-64.3b Transmitter w/APD
ITU-T G.709 Transmitter w/APD

10GBASE-ER/EW Transmitter w/APD
10GBASE-ER/EW + FEC Tx w/APD

40km 10G Fibre Channel Transmitter
w/APD
Finisar’s 40km DWDM FTLX3912M3xx Small Form Factor 10Gb/s XFP transceivers
comply with the current XFP Multi-Source Agreement (MSA) Specification1. The
transmitter specification is based upon SONET OC-192 IR-2, OC-192 IR-3, SDH STM
S-64.2b, STM S-64.3b and 10-Gigabit Ethernet 10GBASE-ER/EW per IEEE 802.3ae but
uses an APD ROSA for additional link budget. Digital diagnostics functions are available
via a 2-wire serial interface, as specified in the XFP MSA. The transceiver is RoHS
compliant and lead free per Directive 2002/95/EC3, and Finisar Application Note AN20384.
PRODUCT SELECTION
FTLX3912M3xx
xx: 100GHz ITU Grid wavelength (see next page)
 Finisar Corporation September 18, 2013
Rev C4
Page 1
FTLX3912M3xx High Link Budget, DWDM XFP – Product Specification
Finisar
Part Numbers for Amplified (OSNR) Applications:
Channel #
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
Product Code
FTLX3912M317
FTLX3912M318
FTLX3912M319
FTLX3912M320
FTLX3912M321
FTLX3912M322
FTLX3912M323
FTLX3912M324
FTLX3912M325
FTLX3912M326
FTLX3912M327
FTLX3912M328
FTLX3912M329
FTLX3912M330
FTLX3912M331
FTLX3912M332
FTLX3912M333
FTLX3912M334
FTLX3912M335
FTLX3912M336
FTLX3912M337
FTLX3912M338
FTLX3912M339
FTLX3912M340
FTLX3912M341
FTLX3912M342
FTLX3912M343
FTLX3912M344
FTLX3912M345
FTLX3912M346
FTLX3912M347
FTLX3912M348
FTLX3912M349
FTLX3912M350
FTLX3912M351
FTLX3912M352
FTLX3912M353
FTLX3912M354
FTLX3912M355
FTLX3912M356
FTLX3912M357
FTLX3912M358
FTLX3912M359
FTLX3912M360
FTLX3912M360
 Finisar Corporation September 18, 2013
Frequency (THz)
191.7
191.8
191.9
192.0
192.1
192.2
192.3
192.4
192.5
192.6
192.7
192.8
192.9
193.0
193.1
193.2
193.3
193.4
193.5
193.6
193.7
193.8
193.9
194.0
194.1
194.2
194.3
194.4
194.5
194.6
194.7
194.8
194.9
195.0
195.1
195.2
195.3
195.4
195.5
195.6
195.7
195.8
195.9
196.0
196.0
Rev C4
Center Wavelength (nm)
1563.86
1563.05
1562.23
1561.42
1560.61
1559.79
1558.98
1558.17
1557.36
1556.55
1555.75
1554.94
1554.13
1553.33
1552.52
1551.72
1550.92
1550.12
1549.32
1548.51
1547.72
1546.92
1546.12
1545.32
1544.53
1543.73
1542.94
1542.14
1541.35
1540.56
1539.77
1538.98
1538.19
1537.40
1536.61
1535.82
1535.04
1534.25
1533.47
1532.68
1531.90
1531.12
1530.33
1529.55
1528.77
Page 2
FTLX3912M3xx High Link Budget, DWDM XFP – Product Specification
Finisar
Part Numbers for Point-to-Point (maximum Link Budget) Applications:
Channel #
17*
18*
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
Product Code
FTLX3912M317P
FTLX3912M318P
FTLX3912M319P
FTLX3912M320P
FTLX3912M321P
FTLX3912M322P
FTLX3912M323P
FTLX3912M324P
FTLX3912M325P
FTLX3912M326P
FTLX3912M327P
FTLX3912M328P
FTLX3912M329P
FTLX3912M330P
FTLX3912M331P
FTLX3912M332P
FTLX3912M333P
FTLX3912M334P
FTLX3912M335P
FTLX3912M336P
FTLX3912M337P
FTLX3912M338P
FTLX3912M339P
FTLX3912M340P
FTLX3912M341P
FTLX3912M342P
FTLX3912M343P
FTLX3912M344P
FTLX3912M345P
FTLX3912M346P
FTLX3912M347P
FTLX3912M348P
FTLX3912M349P
FTLX3912M350P
FTLX3912M351P
FTLX3912M352P
FTLX3912M353P
FTLX3912M354P
FTLX3912M355P
FTLX3912M356P
FTLX3912M357P
FTLX3912M358P
FTLX3912M359P
FTLX3912M360P
FTLX3912M361P
 Finisar Corporation September 18, 2013
Frequency (THz)
191.7
191.8
191.9
192.0
192.1
192.2
192.3
192.4
192.5
192.6
192.7
192.8
192.9
193.0
193.1
193.2
193.3
193.4
193.5
193.6
193.7
193.8
193.9
194.0
194.1
194.2
194.3
194.4
194.5
194.6
194.7
194.8
194.9
195.0
195.1
195.2
195.3
195.4
195.5
195.6
195.7
195.8
195.9
196.0
196.0
Rev C4
Center Wavelength (nm)
1563.86
1563.05
1562.23
1561.42
1560.61
1559.79
1558.98
1558.17
1557.36
1556.55
1555.75
1554.94
1554.13
1553.33
1552.52
1551.72
1550.92
1550.12
1549.32
1548.51
1547.72
1546.92
1546.12
1545.32
1544.53
1543.73
1542.94
1542.14
1541.35
1540.56
1539.77
1538.98
1538.19
1537.40
1536.61
1535.82
1535.04
1534.25
1533.47
1532.68
1531.90
1531.12
1530.33
1529.55
1528.77
Page 3
FTLX3912M3xx High Link Budget, DWDM XFP – Product Specification
I.
Finisar
Pin Descriptions
Pin
1
2
3
Logic
LVTTL-I
4
LVTTL-O
5
6
7
8
9
10
11
LVTTL-I
Symbol
GND
VEE5
Mod-Desel
Interrupt
TX_DIS
VCC5
GND
VCC3
VCC3
SCL
SDA
12
LVTTL-I
LVTTLI/O
LVTTL-O
Mod_Abs
13
LVTTL-O
Mod_NR
14
15
16
17
18
19
20
21
LVTTL-O
LVTTL-I
RX_LOS
GND
GND
RDRD+
GND
VCC2
P_Down/RST
22
23
24
PECL-I
VCC2
GND
RefCLK+
25
PECL-I
RefCLK-
26
27
28
29
30
CML-O
CML-O
CML-I
CML-I
GND
GND
TDTD+
GND
Name/Description
Module Ground
Optional –5.2 Power Supply – Not required
Module De-select; When held low allows the module to
respond to 2-wire serial interface commands
Interrupt (bar); Indicates presence of an important condition
which can be read over the serial 2-wire interface
Transmitter Disable; Transmitter laser source turned off
+5 Power Supply
Module Ground
+3.3V Power Supply
+3.3V Power Supply
Serial 2-wire interface clock
Serial 2-wire interface data line
Ref.
1
Module Absent; Indicates module is not present. Grounded
in the module.
Module Not Ready; Finisar defines it as a logical OR
between RX_LOS and Loss of Lock in TX/RX.
Receiver Loss of Signal indicator
Module Ground
Module Ground
Receiver inverted data output
Receiver non-inverted data output
Module Ground
+1.8V Power Supply – Not Required
Power Down; When high, places the module in the low
power stand-by mode and on the falling edge of P_Down
initiates a module reset
Reset; The falling edge initiates a complete reset of the
module including the 2-wire serial interface, equivalent to a
power cycle.
+1.8V Power Supply – Not Required
Module Ground
Reference Clock non-inverted input, AC coupled on the
host board – Not required
Reference Clock inverted input, AC coupled on the host
board – Not required
Module Ground
Module Ground
Transmitter inverted data input
Transmitter non-inverted data input
Module Ground
2
2
1
2
2
2
2
1
1
1
1
1
1
1
Notes:
1. Module circuit ground is isolated from module chassis ground within the module.
2. Open collector; should be pulled up with 4.7k – 10kohms on host board to a voltage between 3.15V
and 3.6V.
 Finisar Corporation September 18, 2013
Rev C4
Page 4
Finisar
FTLX3912M3xx High Link Budget, DWDM XFP – Product Specification
Diagram of Host Board Connector Block Pin Numbers and Names
II.
Absolute Maximum Ratings
Parameter
Maximum Supply Voltage 1
Maximum Supply Voltage 2
Storage Temperature
Case Operating Temperature
SBS Threshold
Symbol
Vcc3
Vcc5
TS
TOP
TxSBS
 Finisar Corporation September 18, 2013
Min
-0.5
-0.5
-40
0
8
Rev C4
Typ
Max
4.0
6.0
85
70
Unit
V
V
C
C
dBm
Ref.
Page 5
Finisar
FTLX3912M3xx High Link Budget, DWDM XFP – Product Specification
III.
Electrical Characteristics (TOP = 0 to 70 C, VCC5 = 4.75 to 5.25 Volts)
Parameter
Main Supply Voltage
Supply Voltage #2
Supply Current – Vcc5 supply
Supply Current – Vcc3 supply
Module total power
Transmitter
Input differential impedance
Differential data input swing
Transmit Disable Voltage
Transmit Enable Voltage
Transmit Disable Assert Time
Receiver
Differential data output swing
Data output rise time
Data output fall time
LOS Fault
LOS Normal
Power Supply Rejection
Symbol
Vcc5
Vcc3
Icc5
Icc3
P
Rin
Vin,pp
VD
VEN
Vout,pp
tr
tf
VLOS fault
VLOS norm
PSR
Min
4.75
3.13
Typ
Max
5.25
3.45
450
750
3.5
100
120
2.0
GND
340
Vcc – 0.5
GND
820
Vcc
GND+ 0.8
10
650
850
38
38
VccHOST
GND+0.5
See Note 6 below
Unit
V
V
mA
mA
W


mV
V
V
us

mV
ps
ps
V
V
Ref.
1
2
3
4
5
5
6
6
7
Notes:
1. Maximum total power value is specified across the full temperature and voltage range.
2. After internal AC coupling.
3. Or open circuit.
4. Into 100 ohms differential termination.
5. 20 – 80 %
6. Loss Of Signal is open collector to be pulled up with a 4.7k – 10kohm resistor to 3.15 – 3.6V. Logic 0
indicates normal operation; logic 1 indicates no signal detected.
7. Per Section 2.7.1. in the XFP MSA Specification1.
 Finisar Corporation September 18, 2013
Rev C4
Page 6
Finisar
FTLX3912M3xx High Link Budget, DWDM XFP – Product Specification
IV.
Optical Characteristics (TOP = 0 to 70C, VCC5 = 4.75 to 5.25 Volts)
Please note that the Transmitter of the FTLX3912M3xx becomes operational within 5 seconds of powerup. This is due to the time required for the EML to reach its optimum operating temperature.
Parameter
Symbol
Min
Typ
Max
Unit
Ref.
Transmitter

Output Opt. Pwr: 9/125 SMF
POUT
-1
+3
dBm
Optical Extinction Ratio
ER
8.2
dB
Center Wavelength Spacing
100
GHz

Transmitter Center Wavelength – End
X-100
X
X+100
pm
c
Of Life
Transmitter Center Wavelength –
X-25
X
X+25
pm
c
Beginning Of Life
Transmitter Dispersion Penalty
TDP
2
dB
1
(@ 800 ps/nm)
Sidemode Supression ratio
SSRmin
30
dB
Tx Jitter (SONET) 20kHz-80MHz
Txj1
0.3
UI
Tx Jitter (SONET) 4MHz – 80MHz
Txj2
0.1
UI
Relative Intensity Noise
RIN
Receiver
Maximum Input Power
PMAX
-7
Rx Damage Threshold
PDAM
+5
Optical Center Wavelength
1270
C
Receiver Reflectance
Rrx
LOS De-Assert
LOSD
LOS Assert
LOSA
-37
LOS Hysteresis
0.5
Receiver Sensitivity (FTLX3912M3xx & FTLX3912M3xxP)
Data rate
(Gb/s)
BER
Dispersion (ps/nm)
-130
1600
-27
-30
Sensitivity at -300 to
+800ps/nm with
OSNR>30dB
(dB)
-22
-22
-22
-21
-24
-23
-23
Sensitivity back-toback at OSNR>30dB
(dBm)
8.5
1e-12
-300 to +800
9.95
1e-12
-300 to +800
10.3
1e-12
-300 to +800
10.7
1e-12
-300 to +800
10.7
1e-4
-300 to +800
11.1
1e-4
-300 to +800
11.3
1e-4
-300 to +800
OSNR Performance (FTLX3912M3xx ONLY)
dB/Hz

dBm
dBm
nm
dB
dBm
dBm
dB
-24
-24
-24
-24
-27
-27
-27
Data rate
(Gb/s)
BER
Dispersion (ps/nm)
Max OSNR, -300 ps/nm to +800 ps/nm at
Power: -9 to -19dBm (dB)
9.95
10.3
10.7
11.1
11.3
1e-12
1e-12
1e-4
1e-4
1e-4
-300 to +800
-300 to +800
-300 to +800
-300 to +800
-300 to +800
26
26
19
19
19
Threshold
Adjustm.
No
No
No
No
Yes
Yes
Yes
Threshold
Adjustm.
No
No
Yes
Yes
Yes
Notes:
1. 2dB spec is defined for 9.95Gb/s operation
 Finisar Corporation September 18, 2013
Rev C4
Page 7
Finisar
FTLX3912M3xx High Link Budget, DWDM XFP – Product Specification
V. General Specifications
Parameter
Bit Rate
Bit Error Ratio
Max. Supported Link Length
Symbol
BR
BER
LMAX
Min
9.95
Typ
Max
11.3
10-12
40
Units
Gb/s
km
Ref.
1
2
3
Notes:
1. SONET OC-192 IR-2, OC-192 IR-3, 10GBASE-ER/EW, 10G Fibre Channel, ITU-T G.709,
10GBASE-ER/EW + FEC, 10G Fibre Channel + FEC
2. Tested with a 231 – 1 PRBS
3. G.652 fibre
VI.
Environmental Specifications
The FTLX3912M3xx transceiver has an operating case temperature range from 0°C to
+70°C.
Parameter
Case Operating Temperature
Storage Temperature
VII.
Symbol
Top
Tsto
Min
0
-40
Typ
Max
70
85
Units
°C
°C
Ref.
Regulatory Compliance
Finisar XFP transceivers are Class 1 Laser Products. They are certified per the following
standards:
Feature
Agency
Standard
Laser Eye
Safety
Laser Eye
Safety
FDA/CDRH
CDRH 21 CFR 1040 and Laser Notice 50
TÜV
R72101686
Electrical
Safety
Electrical
Safety
TÜV
EN 60825-1: 2007, EN60825-2:2004+A1
IEC 60825-1: 2007 (2nd Edition)
IEC 60825-2: 2010 (3rd Edition)
EN 60950:2006+A11
CLASS 3862.07
CLASS 3862.87
2283290
UL/CSA
Certificate
Number
9210176-77
R72101686
Copies of the referenced certificates are available at Finisar Corporation upon request.
 Finisar Corporation September 18, 2013
Rev C4
Page 8
FTLX3912M3xx High Link Budget, DWDM XFP – Product Specification
Finisar
VIII. Digital Diagnostics Functions
As defined by the XFP MSA1, Finisar XFP transceivers provide digital diagnostic
functions via a 2-wire serial interface, which allows real-time access to the following
operating parameters:





Transceiver temperature
Laser bias current
Transmitted optical power
Received optical power
Transceiver supply voltage
It also provides a sophisticated system of alarm and warning flags, which may be used to
alert end-users when particular operating parameters are outside of a factory-set normal
range.
The operating and diagnostics information is monitored and reported by a Digital
Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed
through the 2-wire serial interface. When the serial protocol is activated, the serial clock
signal (SCL pin) is generated by the host. The positive edge clocks data into the XFP
transceiver into those segments of its memory map that are not write-protected. The
negative edge clocks data from the XFP transceiver. The serial data signal (SDA pin) is
bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to
mark the start and end of serial protocol activation. The memories are organized as a
series of 8-bit data words that can be addressed individually or sequentially. The 2-wire
serial interface provides sequential or random access to the 8 bit parameters, addressed
from 000h to the maximum address of the memory.
For more detailed information, including memory map definitions, please see the XFP
MSA documentation1.
8.5Gb/s Fibre-Channel:
To operate the FTLX3912M3xx at 8.5Gb/s Fibre-Channel, the EEPROM-Table 0, Byte
117, Bit 0 must be set as follows; .
 EEPROM Byte 117, Bit 0, value “1” for 8GFC:
 EEPROM Byte 117, Bit 0 value “0” for 10Gb/s rates:
o (It is also possible to bypass the CDRs with, Byte 111, Bit 0.)
By default, a power cycling the transceiver will return the transceiver to normal 10Gb/s
operation with the CDRs active.
 Finisar Corporation September 18, 2013
Rev C4
Page 9
Finisar
FTLX3912M3xx High Link Budget, DWDM XFP – Product Specification
IX.
Mechanical Specifications
Finisar’s XFP transceivers are compliant with the dimensions defined by the XFP MultiSourcing Agreement (MSA).
77.95
22.15
18.35
13.30
8.50
LATCHED
1.95
16.00
UNLATCHED
20.85
39.00
R1.00
XFP Transceiver (dimensions are in mm)
 Finisar Corporation September 18, 2013
Rev C4
Page 10
FTLX3912M3xx High Link Budget, DWDM XFP – Product Specification
X.
Finisar
PCB Layout and Bezel Recommendations
XFP Host Board Mechanical Layout (dimensions are in mm)
 Finisar Corporation September 18, 2013
Rev C4
Page 11
FTLX3912M3xx High Link Budget, DWDM XFP – Product Specification
Finisar
XFP Detail Host Board Mechanical Layout (dimensions are in mm)
 Finisar Corporation September 18, 2013
Rev C4
Page 12
FTLX3912M3xx High Link Budget, DWDM XFP – Product Specification
Finisar
XFP Recommended Bezel Design (dimensions are in mm)
 Finisar Corporation September 18, 2013
Rev C4
Page 13
FTLX3912M3xx High Link Budget, DWDM XFP – Product Specification
Finisar
XI.
References
1.
10 Gigabit Small Form Factor Pluggable Module (XFP) Multi-Source Agreement
(MSA), Rev 4.5 – August 2005. Documentation is currently available at
http://www.xfpmsa.org/
2.
Application Note AN-2035: “Digital Diagnostic Monitoring Interface for XFP
Optical Transceivers” – Finisar Corporation, December 2003
3.
Directive 2002/95/EC of the European Council Parliament and of the Council,
“on the restriction of the use of certain hazardous substances in electrical and
electronic equipment”. January 27, 2003.
4.
“Application Note AN-2038: Finisar Implementation Of RoHS Compliant
Transceivers”, Finisar Corporation, January 21, 2005.
XII.
Revision History
Revision
Date
Description
A1
8/31/2010

Document created.
C1
4/15/2012

Production Release Datasheet
C4
9/18/2013

Minor corrections
XIII. For More Information
Finisar Corporation
1389 Moffett Park Drive
Sunnyvale, CA 94089-1133
Tel. 1-408-548-1000
Fax 1-408-541-6138
[email protected]
www.finisar.com
 Finisar Corporation September 18, 2013
Rev C4
Page 14
Similar pages