Emcore MAFA-PA-1014-FC1-E-2 Optical preamplifier Datasheet

MAFA 1014-PA Optical Preamplifier
Erbium Doped Fiber Preamplifier
DATASHEET | SEPTEMBER 2013
FIBER OPTICS
EMCORE’s MAFA 1014-PA Optical Preamplifier Erbium Doped Fiber Gain Block Module is
an ideal building block for system integrators to extend the fiber link for long-haul signal
transport. The MAFA 1014-PA Optical Preamplifier series gain blocks are designed to meet
the most demanding noise performance requirements of fiber optic communications and
control systems and performs all the functions required of an optical preamplifier for system
integration.
The MAFA 1014-PA Optical Preamplifier provides output optical isolation for stable, low
noise operation. The output optical signal power level is detected for monitoring and
control. The very low level input optical signal is amplified with active output power control
for constant current mode operation.
Applications
The compact mechanical footprint of the MAFA 1014-PA Optical Preamplifier allows using
this unit to be installed in small space environments.
CATV Systems
Long Distance RF/Microwave Fiber
Optic Communication Links
Sensing and Control Systems
General and Mechanical Specifications
High-Performance Supertrunking Links
High Power Distribution Networks
Parameter
Min
Typ
Max
Units
1532
-
1565
nm
Standard
0
-
50
°C
Standard*
Storage Temperature
-40
-
85
°C
Standard
Operating Humidity
20
-
85
%
Non-condensing
-
+12/+5/+3.3
-
VDC
All Versions**
Redundant Ring Architectures
Operating Wavelength
FTTx Networks
Operating Case Temperature
Features
Voltage Supply Range
Comments
Full Function Fiber Optic pre-Amplifier
Optical Connectors
-
SC; FC; E2000
-
-
User Specified
Low Noise Figure (NF Typ < 3.3 dB)
Dimensions (mm)
-
70 x 90 x 15
-
Mm
All Versions
Pin > -45 dBm
Pout (saturated): ≈ +14 dBm
Small Signal Gain > 37 dB
Low Electrical Power Consumption
* - Extended temperature range of – 40ºC to +75ºC is also possible
** Transient Pulse to +X.X VDC + 5% for < 100 msec
Electrical power must be applied to the unit only after launching input optical
Output Isolation > 40 dB
Polarization Dependant Gain < 0.1 dB
Polarization Mode Dispersion < 0.2 ps
Output Return Losses < -40 dB
Output Residual Pump Power < -40 dBm
| REV 2013.09
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
MAFA 1014-PA Optical Preamplifier
Erbium Doped Fiber Preamplifier
FIBER OPTICS
DATASHEET | SEPTEMBER 2013
Optical/Electrical Characteristics1
Property
Model 1400
Comments (Note 1)
Max
0
-
Min
-45
-
Pout (dBm)
Nominal
14 +/- .25
(Notes 2,3)
NF (dB)
Max
3.3 dB
(Note 4)
(dB)
Max
+/- 0.1
(Note 5)
Psys(W)
Max
2
70°C Case
Unit
Limit
Operating Input Power
Pin (dBm)
Operating Input Power
Pin (dBm)
Saturated Output Power
Noise Figure
Output Power Stability
Power Consumption
(Steady state)
Notes:
1. Unless stated otherwise, all specifications apply over the full operating temperature and humidity ranges
2. Measurement variations
3. Measured @ 1550 nm and Pin = -4 dBm
4. Measure @ 1550 nm and Pin = -30 dBm
5. Over polarization and temperature
Outline Drawing (dimensions in mm)
| REV 2013.09
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
MAFA 1014-PA Optical Preamplifier
Erbium Doped Fiber Preamplifier
FIBER OPTICS
DATASHEET | SEPTEMBER 2013
Compliance and Reliability Information
FCC: Subpart B. Part 15 class “A”: Unintentional Radiators
EN 55013: Sound and Television Broadcast receivers and associated equipment – Radio disturbance characteristics- limits and methods
of measurements – Electric Field Radiation Emissions (2001)
Fit Rate: 90% level of confidence - 290 @ 25°C
Electrical Connector Pinout
PIN #
Designation
PIN #
Designation
1
+12 VDC/+5 VDC/+3.3 VDC
16
LED_Laser_ON
2
+12 VDC/+5 VDC/+3.3 VDC
17
N/A
3
+12 VDC/+5 VDC/+3.3 VDC
18
Pump_Bias_Alarm *
4
+12 VDC/+5 VDC/+3.3 VDC
19
Loss_Input_Power *
5
GND
20
Loss_Output_Power *
6
GND
21
N/A
7
RS232_Rx
22
N/A
8
RS232_Tx
23
N/A
9
GND
24
N/A
10
GND
25
N/A
11
LED_Comm
26
N/A
12
EDFA_Reset
27
N/A
13
EDFA_Disable
28
N/A
14
Pout_Mute
29
N/A
15
EDFA_Temp_Alarm *
30
N/A
* - software adjustable parameters; logic levels (low / high) TBD
Ordering Information
MAFA-PA-1014 -
-
-
Connector Option
Temp Options
Voltage Options
SC1 - SC/APC
S – Standard
1 - +12 VDC
S21 - SC/PC
E – Extended
2 - +5 VDC
FC1- FC/APC
-
3 - +3.3 VDC
FC2- FC/PC
-
-
EC1-E2000/APC
-
-
Example:
MAFA-PA-1014-SC1-S-2: 14 dBm pre-amp gain block with SC/APC optical connectors, standard temperature range, +5 VDC power
supply
| REV 2013.09
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
MAFA 1014-PA Optical Preamplifier
Erbium Doped Fiber Preamplifier
DATASHEET | SEPTEMBER 2013
FIBER OPTICS
Laser Safety Information
This component product does not meet the applicable requirements of 21 CFR 1010 & 1040 and is classified as a Class IIIb laser product
based on the maximum optical output power defined below. During use as intended, the laser energy is fully contained within the fiber
network such that there is no accessible laser radiation and would meet the requirements for a Class I laser product.
Wavelength = 1532 ~ 1565 nm (dependent on input source)
Maximum Output Power = 200 mW
| REV 2013.09
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.
Similar pages