PAIRUI LPU-120C Constant current led driver Datasheet

Constant current LED Drivers
For outdoor use
LPU-120C Series, 120Watt
FEATURES:
Constant current output
Input voltage range 100-277Vac
Short circuit, over current, over voltage and over
temperature protections
Designed to worldwide safety standards for lighting
Active power factor correction
IP67 for outdoor use
Multiple dimming
5 year warranty
Model
Input voltage
(Vac)
Output voltage
(Vdc)
Output current
(mA)
Min.
Max.
Output power
(W)
LPU120-C350
350
172
343
120
LPU120-C530
530
113
226
119.8
LPU120-C700
700
86
171
119.7
LPU120-C1050
1050
57
114
119.7
LPU120-C1400
1400
43
86
120.4
1750
35
69
120.75
LPU120-C2100
2100
29
57
119.7
LPU120-C2800
2800
22
43
120.4
LPU120-C3500
3500
17
34
119
LPU120-C5000
5000
12
24
120
LPU120-C1750
100-277
Note:
You may request for the models with different dimming functions, plus “D/P/T/A” in the suffix: e.g. LPU120-C350D.
Blank
A
—Without Dimming
—3 in 1 Programmable Dimming
D
—0-10V or Resistor Dimming
—PWM Dimming
—
P
T Timer Dimming
ELECTRICAL
Input
Parameters
Symbols
Test Conditions / Comment
Min.
Typ.
Max.
Units
Input Voltage
Vin
---
100
--
277
Vac
Input Frequency
Fline
---
47
--
63
Hz
Iin
Vin=100Vac
Full Load, Vin=220Vac
Full Load, Vin=277Vac
--
Cold Start, Vin =230Vac
--
1.2
Full Load,
Input Current
Inrush Current
www.pairuigroup.com
Iinrush
Page:
1/8
--
0.56
A
0.45
--
50
A
Date: 04/29/2014
Constant current LED Drivers
For outdoor use
LPU-120C Series, 120Watt
ELECTRICAL
Input
Parameters
Power Factor
Total Harmonic
Distortion
Symbols
PF
Test Conditions / Comment
Min.
70% ~100% Load, Vin =100Vac
0.98
70% ~100% Load, Vin =220Vac
0.95
70% ~100% Load, Vin =277Vac
0.90
Typ.
Max.
Units
--
--
PF
70% ~100% Load, Vin =100Vac
THD
70% ~100% Load, Vin =220Vac
10
--
--
70% ~100% Load, Vin =277Vac
20
%
25
Efficiency
η
Full voltage, full load
88
91
93
%
Leakage Current
Ileakage
Vin =277Vac/ 60Hz
--
--
0.5
mA
LPU120-C350
332
350
368
mA
LPU120-C530
503
530
557
mA
LPU120-C700
665
700
735
mA
LPU120-C1050
997
1050
1102
mA
LPU120-C1400
1330
1400
1470
mA
LPU120-C1750
1663
1750
1837
mA
LPU120-C2100
1995
2100
2205
mA
LPU120-C2800
2660
2800
2940
mA
LPU120-C3500
3325
3500
3675
mA
LPU120-C5000
4750
5000
5250
mA
LPU120-C350
172
--
343
V
LPU120-C530
113
--
226
V
LPU120-C700
86
--
171
V
LPU120-C1050
57
--
114
V
LPU120-C1400
43
--
86
V
LPU120-C1750
35
--
69
V
LPU120-C2100
29
--
57
V
LPU120-C2800
22
--
43
V
LPU120-C3500
17
--
34
V
LPU120-C5000
12
--
24
V
Output
Output Current
Output Voltage
Iout
Vout
Line Regulation
Iout-line
Vin from 100Vac to 277Vac
--
--
1
%
Load Regulation
Iout-load
Vout from min. to max.
--
--
1
%
Turn-On Delay Time
Ton_delay
Cold Start, Power ON
--
1
1.5
S
www.pairuigroup.com
Page:
2/8
Date: 04/29/2014
Constant current LED Drivers
For outdoor use
LPU-120C Series, 120Watt
ELECTRICAL
Output
Parameters
Symbols
Test Conditions / Comment
Min.
Typ.
Max.
Units
Ripple Current
Iout-ripple
Full Load, (pk-to-pk)/Average
--
--
20
%
Iovershoot
Turning Power ON
--
--
10
%
11
12
13
V
0
--
100
mA
--
--
1.2
W
Output Current
Overshoot
+12V Auxiliary Output (Optional)
12V Output Voltage
VAUX
12V Output Current
IAUX
A +12V auxiliary output provides
power for active LED cooler or other
active equipment.
Auxiliary Power
PAUX
0-10V or Resistor Dimming
The 0-10V or resistor dimming is a dimming manner that can be used to dim the output current via a standard commercial
wall dimmer (0-10Vdc or 1-10Vdc) or an external control voltage source (0-10Vdc or 1-10Vdc) or external resistor.
Iout to 5% Iout. When VDIM is 9-10Vdc, the output current maintains 100%Iout, and when
VDIM is 1V, the output current is 5% Iout.
When VDIM below 0.7V, the driver will shut down and it will recovery when VDIM goes above 1V.
The dimming range is 100%
See “0-10V Dimming Curve” for detailed information.
Absolute Maximum
Voltage on 0-10V pin
Source Current on
0-10V Dimming Pin
VDIM Voltage for
Full Bright
Minimum Output
Current
VDIMVoltage When
The Driver Shut Down
VDIM
---
2
--
15
V
IDIM
---
50
75
100
μA
VDIM-MAX
---
9
--
--
V
IOUT-MIN
VDIM=1V
--
5%
--
% of Iout
VDIM-SHUT
---
0.6
0.7
0.8
V
VDIM -recovery
---
0.9
1
1.1
V
--
20
--
KΩ
VDIM Voltage When
the Driver Recovery
After Shut Down
External Resistor
Value at Full Bright
www.pairuigroup.com
RExternal-MAX
See “External Resistor Dimming
Curve (D Type)” for details
Page:
3/8
Date: 04/29/2014
Constant current LED Drivers
For outdoor use
LPU-120C Series, 120Watt
ELECTRICAL
PWM Dimming
The PWM dimming is a dimming manner that can be used to dim the output current via the duty cycle of PWM signal.
The dimming range is 100% Iout to 5% Iout . When the duty cycle is 100%, the output current reaches 100% Iout, and the
output current maintains 5% Iout when the duty cycle below 5%.
When the PWM signal is low the driver will shut down and it will recovery when the duty cycle goes above 5%.
See “PWM Dimming Curve” for detailed information.
Parameters
Symbols
Test Conditions / Comment
Min.
Typ.
Max.
Units
PWM Frequency
FPWM
---
0.1
--
2
KHz
VPWM-High
---
4
--
1.2
V
VPWM-Low
---
0
--
1
V
IOUT-MIN
When duty cycle below 5%
--
5
--
% of Iout
High Level Voltage of
PWM Signal
Lower Level Voltage
of PWM Signal
Minimum Output
Current
Timer Dimming
The Timer Dimming is designed with time controlled dimming function, it will dim to 50% of rated output current after
operating six hours.
See “ T Type Dimming Curve” for detailed information.
Full Load Operated
TFULL-LOAD-TTY
Time
The
dimming
time
and
dimming current can be customized
PE
Dim Output Current
Note1,
5.5
6
6.5
Hrs
45
50
55
% of Iout
Note2, Timing shut down function
IOUT-MIN-TTYPE
can be customized
LED Board Temperature Detection(Optional)
The LED board temperature detection input can be connected to a thermistor (NTC) to realize a LED Board Over Temperature
Protection and prevent the LED lamp from damage or luminous decay at high temperature.
The thermistor should be located on the LED assembly to monitor its temperature. If the temperature exceeds the
predetermined LED OTP point, the output current of the driver is automatically reduced to regulate the temperature of the
LED board at a safe level.
See “LED OTP Current Reduction Curve” for detailed information.
Thermistor Resistance
Value that Start
Current
Reduction
www.pairuigroup.com
When the thermistor resistance less
RLEDOTP
than this value the output current
--
4
--
KΩ
start reduce.
Page:
4/8
Date: 04/29/2014
Constant current LED Drivers
For outdoor use
LPU-120C Series, 120Watt
ELECTRICAL
Protection
Parameters
Symbols
Test Conditions / Comment
Min.
Typ.
Max.
Units
Over Voltage
VOVP
---
--
110%
150%
Vout
Short Circuit
Hiccup mode, it will recover automatically after fault conditions remove
If the temperature exceeds OTP
Over Temperature
VOVP
point, the output current of the
90
95
100
℃
driver is automatically reduced.
Environment
Storage
Temperature
Ambient Operating
Temperature
Maximum Case
Temperature
Operating Relative
Humidity
Tstorage
Humidity: 5% RH to 95% RH
-40
--
+85
℃
Ta
Startup at rated voltage
-40
--
+70
℃
TC
Hot-spot on case
--
--
+90
℃
Ha
Non condensing
10
--
95
%
50
--
--
kHrs
200
--
--
kHrs
--
790
--
g
Life Time
TLife
MTBF
TMTBF
Net Weight
WNBT
℃
Full load, case temperature 55
Full load, 220Vac input,
℃ Ambient temperature
25
---
Dimension(LxWxH)
192 x 70 x 34mm
EMC Compliance
EN55015
EN61000-3-2 Class C
EN61000-3-3
FCC Part 15 Class B
EN61547
Conducted Emission & Radiated Emission
Harmonic Current Emission
Voltage fluctuations and flicker
Conducted and Radiated Emission Measurement
Equipment for general lighting purposes: EMC Immunity Requirements
EN61000-4-2
Electrostatic Discharge (ESD). Air Discharge: 15kV; Contact Discharge: 8kV
EN61000-4-3
Radiated Radio-Frequency electromagnetic field
EN61000-4-4
Electrical Fast Transient / burst
EN61000-4-5
Surge Immunity Test: L-N 6KV, L/N-GND 6KV
EN61000-4-6
Conducted disturbances induced by Radio-Frequency fields
EN61000-4-8
Power Frequency Magnetic Field Test
www.pairuigroup.com
Page:
5/8
Date: 04/29/2014
Constant current LED Drivers
For outdoor use
LPU-120C Series, 120Watt
ELECTRICAL
EMC Compliance
EN61000-4-11
Voltage Dips, short interruptions and Voltage Variations
Note: Unless otherwise specified, all the above parameters are measured at ambient temperature of 25
100Vac to 277Vac.
℃
and Vin =
TYPICAL APPLICATION
Timer Dimming
LPU-120C
Series
Versatile control features:
A Temperature sensor(NTC thermistor) protects the LED from over temperature;
12V/100mA Auxiliary output can be used to power auxiliary loads such as active cooler or external dimming controller;
Accepts various manner to dim the output current and the dimming range is 5% to 100%Iout;
Support shut down functions at dimming applications.
TYPICAL CHARACTERISTICS CURVE
Power Factor VS. Load
www.pairuigroup.com
Efficiency VS. Load
Page:
6/8
Date: 04/29/2014
Constant current LED Drivers
For outdoor use
LPU-120C Series, 120Watt
TYPICAL CHARACTERISTICS CURVE
Output Current VS. Dimming Voltage
Output Current VS. External Resistor
Output current VS. Duty Cycle of PWM Signal
Output Current VS. Running Time
Current Reduction VS. Thermistor Resistance Value
www.pairuigroup.com
Page:
7/8
Date: 04/29/2014
Constant current LED Drivers
For outdoor use
LPU-120C Series, 120Watt
MECHANICAL
No Dimming & Timer Dimming Version
Unit: mm
0~10Vdc or Resistor Dimming & PWM Dimming Version
Unit: mm
www.pairuigroup.com
Page:
8/8
Date: 04/29/2014
Similar pages