Freescale MCF547X Mcf547x integrated microprocessor electrical characteristic Datasheet

Freescale Semiconductor
Data Sheet
MCF5475EC
Rev. 2, 10/2004
MCF547x Integrated
Microprocessor Electrical
Characteristics
Applies to the MCF5470, MCF5471, MCF5472, MCF5473,
MCF5474, and MCF5475
This chapter contains electrical specification tables and
reference timing diagrams for the MCF547x
microprocessor. This section contains detailed
information on power considerations, DC/AC electrical
characteristics, and AC timing specifications of the
MCF547x.
NOTE
The parameters specified
in this MPU document
supersede any values
found in the module
specifications.
1
Maximum Ratings
Table 1 lists maximum and minimum ratings for supply
and operating voltages and storage temperature.
Operating outside of these ranges may cause erratic
behavior or damage to the processor.
© Freescale Semiconductor, Inc., 2004. All rights reserved.
Table of Contents
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Maximum Ratings................................................1
Thermal Characteristics ......................................2
DC Electrical Specifications ................................3
Supply Voltage Sequencing and Separation
Cautions ..............................................................5
Output Driver Capability and Loading .................6
PLL Timing Specifications ...................................7
Reset Timing Specifications ................................8
FlexBus................................................................8
SDRAM Bus ......................................................11
PCI Bus .............................................................17
Fast Ethernet AC Timing Specifications ............18
General Timing Specifications...........................21
I2C Input/Output Timing Specifications .............21
JTAG and Boundary Scan Timing .....................23
DSPI Electrical Specifications ...........................26
Timer Module AC Timing Specifications............26
Thermal Characteristics
Table 1. Absolute Maximum Ratings
Rating
Symbol
Value
Units
External (I/O pads) supply voltage (3.3-V power pins)
EVDD
–0.3 to +4.0
V
Internal logic supply voltage
IVDD
–0.5 to +2.0
V
Memory (I/O pads) supply voltage (2.5-V power pins)
SD VDD
–0.3 to +4.0 SDR Memory
–0.3 to +2.8 DDR Memory
V
PLL supply voltage
PLL VDD
–0.5 to +2.0
V
Internal logic supply voltage, input voltage level
Vin
–0.5 to +3.6
V
Storage temperature range
Tstg
–55 to +150
2
Thermal Characteristics
2.1
Operating Temperatures
o
C
Table 2 lists junction and ambient operating temperatures.
Table 2. Operating Temperatures
Characteristic
Symbol
Value
Units
Maximum operating junction temperature
Tj
105
oC
Maximum operating ambient temperature
TAmax
<701
oC
Minimum operating ambient temperature
TAmin
–0
oC
NOTES:
1 This published maximum operating ambient temperature should be used only as a system design guideline. All
device operating parameters are guaranteed only when the junction temperature lies within the specified range.
2.2
Thermal Resistance
Table 3 lists thermal resistance values.
Table 3. Thermal Resistance
Characteristic
Symbol
Value
Unit
324 pin TEPBGA — Junction to ambient, natural Four layer board (2s2p)
convection
θJMA
22–241,2
°C/W
388 pin TEPBGA — Junction to ambient, natural Four layer board (2s2p)
convection
θJMA
20–221,2
°C/W
Junction to ambient (@200 ft/min)
θJMA
231,2
°C/W
Junction to board
θJB
153
°C/W
Junction to case
θJC
104
°C/W
Ψjt
21,5
°C/W
Junction to top of package
Four layer board (2s2p)
Natural convection
MCF547x Integrated Microprocessor Electrical Characteristics, Rev. 2
2
Freescale Semiconductor
DC Electrical Specifications
NOTES:
1
θJA and Ψjt parameters are simulated in accordance with EIA/JESD Standard 51-2 for natural convection.
Freescale recommends the use of θJA and power dissipation specifications in the system design to prevent device
junction temperatures from exceeding the rated specification. System designers should be aware that device
junction temperatures can be significantly influenced by board layout and surrounding devices. Conformance to the
device junction temperature specification can be verified by physical measurement in the customer’s system using
the Ψjt parameter, the device power dissipation, and the method described in EIA/JESD Standard 51-2.
2
Per JEDEC JESD51-6 with the board horizontal.
3
Thermal resistance between the die and the printed circuit board per JEDEC JESD51-8. Board temperature is
measured on the top surface of the board near the package.
4
Thermal resistance between the die and the case top surface as measured by the cold plate method (MIL
SPEC-883 Method 1012.1).
5 Thermal characterization parameter indicating the temperature difference between package top and the junction
temperature per JEDEC JESD51-2. When Greek letters are not available, the thermal characterization parameter
is written as Psi-JT.
3
DC Electrical Specifications
Table 4 lists DC electrical operating temperatures. This table is based on an operating voltage of
EVDD = 3.3 VDC ± 0.3 VDC and IVDD of 1.5 ± 0.07 VDC.
Table 4. DC Electrical Specifications
Characteristic
Symbol
Min
Max
Units
EVDD
3.0
3.6
V
SD VDD
2.30
2.70
V
IVDD
1.43
1.58
V
PLL VDD
1.43
1.58
V
USB_OSVDD
3.0
3.6
V
USBVDD
3.0
3.6
V
USB_PHYVDD
3.0
3.6
V
USB_OSCAVDD
1.43
1.58
V
USB_PLLVDD
1.43
1.58
V
Input high voltage SSTL 3.3V (SDR DRAM)
VIH
2.0
3.6
V
Input low voltage SSTL 3.3V (SDR DRAM)
VIL
–0.5
0.8
V
Input high voltage SSTL 2.5V (DDR DRAM)
VIH
2.0
2.8
V
Input low voltage SSTL 2.5V (DDR DRAM)
VIL
–0.5
0.8
V
Output high voltage IOH = 8 mA, 16 mA,24 mA
VOH
2.4
—
V
Output low voltage IOL = 8 mA, 16 mA,24 mA5
VOL
—
0.5
V
CIN
—
TBD
pF
External (I/O pads) operation voltage range
Memory (I/O pads) operation voltage range (DDR Memory)
Internal logic operation voltage range 1
PLL Analog operation voltage range
1
USB oscillator operation voltage range
USB digital logic operation voltage range
USB PHY operation voltage range
USB oscillator analog operation voltage range
USB PLL operation voltage range
Capacitance
2,
Vin = 0 V, f = 1 MHz
NOTES:
1
IVDD and PLL VDD should be at the same voltage. PLL VDD should have a filtered input. Please see Figure 1 for an
example circuit. Note: There are three PLL VDD inputs. A filter circuit should used on each PLL VDD input.
2 Capacitance C is periodically sampled rather than 100% tested.
IN
MCF547x Integrated Microprocessor Electrical Characteristics, Rev. 2
Freescale Semiconductor
3
DC Electrical Specifications
3.1
PLL Power Filtering
To further enhance noise isolation, an external filter is strongly recommended for PLL analog VDD pins.
The filter shown in Figure 1 should be connected between the board VDD and the PLL VDD pins. The
resistor and capacitors should be placed as close to the dedicated PLL VDD pin as possible.
10 W
Board VDD
PLL VDD Pin
10 µF
0.1 µF
GND
Figure 1. System PLL VDD Power Filter
3.2
USB Power Filtering
To minimize noise, a external filters are required for each of the USB power pins. The filter shown in
Figure 2 should be connected between the board EVDD or IVDD and each of the USB VDD pins. The
resistor and capacitors should be placed as close to the dedicated USB VDD pin as possible. A separate
filter circuit should be included for each USB VDD pin, a total of five circuits.
R
Board EVDD/IVDD
USB VDD Pin
10 µF
0.1 µF
GND
Figure 2. USB VDD Power Filter
NOTE
In addition to the above filter circuitry, a 0.01 F capacitor is also
recommended in parallel with those shown.
Table 5 lists the resistor values and supply voltages to be used in the circuit for each of the USB VDD pins.
Table 5. USB Filter Circuit Values
USB VDD Pin
Nominal Voltage
Resistor Value (R)
USB_OSCVDD
3.3V
0Ω
USBVDD
3.3V
0Ω
USB_PHYVDD
3.3V
0Ω
USB_OSCAVDD
1.5V
0Ω
USB_PLLVDD
1.5V
10Ω
MCF547x Integrated Microprocessor Electrical Characteristics, Rev. 2
4
Freescale Semiconductor
Supply Voltage Sequencing and Separation Cautions
4
Supply Voltage Sequencing and Separation
Cautions
DC Power Supply Voltage
Figure 3 shows situations in sequencing the I/O VDD (EVDD), SDRAM VDD (SD VDD), PLL VDD (PLL
VDD), and Core VDD (IVDD).
EVDD, SD VDD (3.3V)
3.3V
Supplies Stable
2.5V
1.5V
SD VDD (2.5V)
IVDD, PLL VDD
1
2
0
Time
NOTES:
1. IVDD should not exceed EVDD, SD VDD or PLL VDD by more than
0.4V at any time, including power-up.
2. Recommended that IVDD/PLL VDD should track EVDD/SD VDD up to
0.9V, then separate for completion of ramps.
3. Input voltage must not be greater than the supply voltage (EVDD, SD VDD,
IVDD, or PLL VDD) by more than 0.5V at any time, including during power-up.
4. Use 1 microsecond or slower rise time for all supplies.
Figure 3. Supply Voltage Sequencing and Separation Cautions
The relationship between SD VDD and EVDD is non-critical during power-up and power-down sequences.
Both SD VDD (2.5V or 3.3V) and EVDD are specified relative to IVDD.
4.1
Power Up Sequence
If EVDD/SD VDD are powered up with the IVDD at 0V, then the sense circuits in the I/O pads will cause
all pad output drivers connected to the EVDD/SD VDD to be in a high impedance state. There is no limit
on how long after EVDD/SD VDD powers up before IVDD must power up. IVDD should not lead the EVDD,
SD VDD or PLL VDD by more than 0.4V during power ramp up, or there will be high current in the internal
ESD protection diodes. The rise times on the power supplies should be slower than 1 microsecond to avoid
turning on the internal ESD protection clamp diodes.
MCF547x Integrated Microprocessor Electrical Characteristics, Rev. 2
Freescale Semiconductor
5
Output Driver Capability and Loading
The recommended power up sequence is as follows:
1. Use 1 microsecond or slower rise time for all supplies.
2. IVDD/PLL VDD and EVDD/SD VDD should track up to 0.9V, then separate for the completion of
ramps with EVDD/SD VDD going to the higher external voltages. One way to accomplish this is to
use a low drop-out voltage regulator.
4.2
Power Down Sequence
If IVDDPLL VDD are powered down first, then sense circuits in the I/O pads will cause all output drivers
to be in a high impedance state. There is no limit on how long after IVDD and PLL VDD power down before
EVDD or SD VDD must power down. IVDD should not lag EVDD, SD VDD, or PLL VDD going low by
more than 0.4V during power down or there will be undesired high current in the ESD protection diodes.
There are no requirements for the fall times of the power supplies.
The recommended power down sequence is as follows:
1. Drop IVDD/PLL VDD to 0V
2. Drop EVDD/SD VDD supplies
5
Output Driver Capability and Loading
Table 6 lists values for drive capability and output loading.
Table 6. I/O Driver Capability
Signal
Drive
Output
Capability Load (CL)
SDRAMC (SDADDR[12:0], SDDATA[31:0], RAS, CAS, SDDM[3:0],
SDWE, SDBA[1:0]
24 mA
15 pF
SDRAMC DQS and clocks (SDDQS[3:0], SDRDQS, SDCLK[1:0],
SDCLK[1:0], SDCKE)
24 mA
15 pF
SDRAMC chip selects (SDCS[3:0])
24 mA
15 pF
FlexBus (AD[31:0], FBCS[5:0], ALE, R/W, BE/BWE[3:0], OE)
16 mA
20 pF
FEC (EnMDIO, EnMDC, EnTXEN, EnTXD[3:0], EnTXER
8 mA
15 pF
Timer (TOUT[3:0])
8 mA
50 pF
DACK[1:0]
8 mA
30 pF
PSC (PSCnTXD[3:0], PSCnRTS/PSCnFSYNC,
8 mA
30 pF
DSPI (DSPISOUT, DSPICS0/SS, DSPICS[2:3], DSPICS5/PCSS)
24 mA
50 pF
PCI (PCIAD[31:0], PCIBG[4:1], PCIBG0/PCIREQOUT, PCIDEVSEL,
PCICXBE[3:0], PCIFRM, PCIPERR, PCIRESET, PCISERR, PCISTOP,
PCIPAR, PCITRDY, PCIIRDY
16 mA
50 pF
I2C (SCL, SDA)
8 mA
50 pF
BDM (PSTCLK, PSTDDATA[7:0], DSO/TDO,
8 mA
25 pF
RSTO
8 mA
50 pF
MCF547x Integrated Microprocessor Electrical Characteristics, Rev. 2
6
Freescale Semiconductor
PLL Timing Specifications
6
PLL Timing Specifications
The specifications in Table 7 are for the CLKIN pin.
Table 7. Clock Timing Specification
Num Characteristic
Min
Max
Units
15.15
33.3
ns
C1
Cycle time
C2
Rise time (20% of Vdd to 80% of vdd)
—
2
ns
C3
Fall time (80% of Vdd to 20% of Vdd)
—
2
ns
C4
Duty cycle (at 50% of Vdd)
40
60
%
C1
CLKIN
C4
C4
C2
C3
Input Clock Timing Diagram
Table 8 shows the supported PLL encodings.
Table 8. MCF547X Divide Ratio Encodings
CLKIN—PCI and FlexBus
Clock Ratio
Frequency Range
(MHz)
AD[12:8]1
Internal XLB, SDRAM
Bus, and PSTCLK
Frequency Range
(MHz)
Core Frequency Range
(MHz)
00011
1:2
41.6–66.66
83.33–133.33
166.66–266.66
00101
1:2
25.0–44.4
50.0–88.8
100.0–177.66
01111
1:4
25.0–33.3
100–133.33
200–266.66
NOTES:
1 All other values of AD[12:8] are reserved.
Figure 4 correlates CLKIN, internal bus, and core clock frequencies for the 1x–4x multipliers.
CLKIN
Internal Clock
Core Clock
2x
25.0
2x
50.0
66.66
4x
50
100.0
70
266.66
2x
25.0 33.33
25
100.0
133.33
30
CLKIN (MHz)
50
70
90
110
Internal Clock (MHz)
133.33
130
266.66
200.0
60
80
100
120
140
160
180
200
220
240
260
Core Clock (MHz)
Figure 4. CLKIN, Internal Bus, and Core Clock Ratios
MCF547x Integrated Microprocessor Electrical Characteristics, Rev. 2
Freescale Semiconductor
7
Reset Timing Specifications
7
Reset Timing Specifications
Table 9 lists specifications for the reset timing parameters shown in Figure 5
Table 9. Reset Timing Specification
66 MHz CLKIN
Num
Characteristic
Units
Min
Max
R1 1
Valid to CLKIN (setup)
8
—
nS
R2
CLKIN to invalid (hold)
1.0
—
nS
R3
RSTI to invalid (hold)
1.0
—
nS
NOTES:
1 RSTI and FlexBus data lines are synchronized internally. Setup and hold
times must be met only if recognition on a particular clock is required.
Figure 5 shows reset timing for the values in Table 9.
CLKIN
R1
RSTI
R2
Mode Select
FlexBus
R1
R3
NOTE:
Mode selects are registered on the rising clock edge before
the cycle in which RSTI is recognized as being negated.
Figure 5. Reset Timing
8
FlexBus
A multi-function external bus interface called FlexBus is provided on the MCF5472 with basic
functionality to interface to slave-only devices up to a maximum bus frequency of 66 MHz. It can be
directly connected to asynchronous or synchronous devices such as external boot ROMs, flash memories,
gate-array logic, or other simple target (slave) devices with little or no additional circuitry. For
asynchronous devices, a simple chip-select based interface can be used. The FlexBus interface has six
general purpose chip-selects (FBCS[5:0]). Chip-select FBCS0 can be dedicated to boot ROM access and
can be programmed to be byte (8 bits), word (16 bits), or longword (32 bits) wide. Control signal timing
is compatible with common ROM / flash memories.
MCF547x Integrated Microprocessor Electrical Characteristics, Rev. 2
8
Freescale Semiconductor
FlexBus
8.1
FlexBus AC Timing Characteristics
The following timing numbers indicate when data will be latched or driven onto the external bus, relative
to the system clock.
Table 10. FlexBus AC Timing Specifications
Num
Characteristic
Frequency of Operation
Min
Max
Unit
Notes
30
66
Mhz
1
15.15
33.33
ns
2
FB1
Clock Period (CLKIN)
FB2
Address, Data, and Control Output Valid (AD[31:0], FBCS[5:0],
R/W, ALE, TSIZ[1:0], BE/BWE[3:0], OE, and TBST)
—
7.0
ns
3
FB3
Address, Data, and Control Output Hold ((AD[31:0], FBCS[5:0],
R/W, ALE, TSIZ[1:0], BE/BWE[3:0], OE, and TBST)
1
—
ns
3, 4
FB4
Data Input Setup
3.5
—
ns
FB5
Data Input Hold
0
—
ns
FB6
Transfer Acknowledge (TA) Input Setup
4
—
ns
FB7
Transfer Acknowledge (TA) Input Hold
0
—
ns
FB8
Address Output Valid (PCIAD[31:0])
—
7.0
ns
5
FB9
Address Output Hold (PCIAD[31:0])
0
—
ns
5
NOTES:
1 The frequency of operation is the same as the PCI frequency of operation. The MCF547X supports a single
external reference clock (CLKIN). This signal defines the frequency of operation for both FlexBus and PCI.
2 Max cycle rate is determined by CLKIN and how the user has the system PLL configured.
3 Timing for chip selects only applies to the FBCS[5:0] signals. Please see Section 9.2, “DDR SDRAM AC
Timing Characteristics” for SDCS[3:0] timing.
4
The FlexBus supports programming an extension of the address hold. Please consult the MCF547X
specification manual for more information.
5
These specs are used when the PCIAD[31:0] signals are configured as 32-bit, non-muxed FlexBus address
signals.
MCF547x Integrated Microprocessor Electrical Characteristics, Rev. 2
Freescale Semiconductor
9
FlexBus
CLKIN
FB1
FB3
AD[X:0]
A[X:0]
FB2
AD[31:Y]
FB5
A[31:Y]
DATA
R/W
FB4
ALE
TSIZ[1:0]
TSIZ[1:0]
FBCSn, BE/BWEn
FB7
OE
FB6
TA
Figure 6. FlexBus Read Timing
MCF547x Integrated Microprocessor Electrical Characteristics, Rev. 2
10
Freescale Semiconductor
SDRAM Bus
CLKIN
FB1
FB3
AD[X:0]
A[X:0]
FB2
AD[31:Y]
FB3
A[31:Y]
DATA
R/W
ALE
TSIZ[1:0]
TSIZ[1:0]
FBCSn, BE/BWEn
FB7
OE
FB6
TA
Figure 7. FlexBus Write Timing
9
SDRAM Bus
The SDRAM controller supports accesses to main SDRAM memory from any internal master. It supports
either standard SDRAM or double data rate (DDR) SDRAM, but it does not support both at the same time.
The SDRAM controller uses SSTL2 and SSTL3 I/O drivers. Both SSTL drive modes are programmable
for either Class I or Class II drive strength.
9.1
SDR SDRAM AC Timing Characteristics
The following timing numbers indicate when data will be latched or driven onto the external bus, relative
to the memory bus clock, when operating in SDR mode on write cycles and relative to SDR_DQS on read
cycles. The MCF547x SDRAM controller is a DDR controller that has an SDR mode. Because it is
designed to support DDR, a DQS pulse must still be supplied to the MCF547x for each data beat of an
SDR read. The MCF547x accomplishes this by asserting a signal called SDR_DQS during read cycles.
Care must be taken during board design to adhere to the following guidelines and specs with regard to the
SDR_DQS signal and its usage.
MCF547x Integrated Microprocessor Electrical Characteristics, Rev. 2
Freescale Semiconductor
11
SDRAM Bus
Table 11. SDR Timing Specifications
Symbol
Characteristic
Frequency of Operation
Min
Max
Unit
Notes
83
133
Mhz
1
7.52
12
ns
2
SD1
Clock Period (tCK)
SD2
Clock Skew (tSK)
SD3
Pulse Width High (tCKH)
0.45
0.55
SDCLK
3
SD4
Pulse Width Low (tCKL)
0.45
0.55
SDCLK
4
SD5
Address, CKE, CAS, RAS, WE, BA, CS - Output Valid (tCMV)
0.5 × SDCLK +
1.0ns
ns
SD6
Address, CKE, CAS, RAS, WE, BA, CS - Output Hold (tCMH)
SD7
SDRDQS Output Valid (tDQSOV)
SD8
SDDQS[3:0] input setup relative to SDCLK (tDQSIS)
SD9
SDDQS[3:0] input hold relative to SDCLK (tDQSIH)
SD10
Data Input Setup relative to SDCLK (reference only) (tDIS)
0.25 × SDCLK
ns
SD11
Data Input Hold relative to SDCLK (reference only) (tDIH)
1.0
ns
SD12
Data and Data Mask Output Valid (tDV)
SD13
Data and Data Mask Output Hold (tDH)
TBD
2.0
0.25 × SDCLK
ns
Self timed
ns
5
0.40 × SDCLK
ns
6
Does not apply. 0.5 SDCLK fixed width.
0.75 × SDCLK
+0.500ns
1.5
7
8
ns
ns
NOTES:
1 The frequency of operation is either 2x or 4x the CLKIN frequency of operation. The MCF547X supports a single external
reference clock (CLKIN). This signal defines the frequency of operation for both FlexBus and PCI, but SDRAM clock
operates at the same frequency as the internal bus clock. Please see the PLL chapter of the MCF547X Specification for
more information on setting the SDRAM clock rate.
2
SDCLK is one SDRAM clock in (ns).
3
Pulse width high plus pulse width low cannot exceed min and max clock period.
4
Pulse width high plus pulse width low cannot exceed min and max clock period.
5 SDR_DQS is designed to pulse 0.25 clock before the rising edge of the memory clock. This is a guideline only. Subtle
variation from this guideline is expected. SDR_DQS will only pulse during a read cycle and one pulse will occur for each
data beat.
6 SDR_DQS is designed to pulse 0.25 clock before the rising edge of the memory clock. This spec is a guideline only. Subtle
variation from this guideline is expected. SDR_DQS will only pulse during a read cycle and one pulse will occur for each
data beat.
7 The SDR_DQS pulse is designed to be 0.5 clock in width. The timing of the rising edge is most important. The falling edge
does not affect the memory controller.
8 Since a read cycle in SDR mode still uses the DQS circuit within the MCF547X, it is most critical that the data valid window
be centered 1/4 clk after the rising edge of DQS. Ensuring that this happens will result in successful SDR reads. The input
setup spec is just provided as guidance.
MCF547x Integrated Microprocessor Electrical Characteristics, Rev. 2
12
Freescale Semiconductor
SDRAM Bus
SD2
SD3
SD1
SDCLK0
SD4
SD2
SDCLK1
SD6
SDCSn,SDWE,
RAS, CAS
CMD
SD5
SDADDR,
SDBA[1:0]
ROW
COL
SD12
SDDM
SD13
SDDATA
WD1
WD2
WD3
WD4
Figure 8. SDR Write Timing
MCF547x Integrated Microprocessor Electrical Characteristics, Rev. 2
Freescale Semiconductor
13
SDRAM Bus
SD1
SD2
SDCLK0
SD2
SDCLK1
SD6
SDCSn,SDWE,
RAS, CAS
CMD
3/4 MCLK
Reference
SD5
SDADDR,
SDBA[1:0]
ROW
COL
tDQS
SDDM
SD7
SDRQS
(Measured at Output Pin)
Board Delay
SDDQS
SD9
(Measured at Input Pin)
Board Delay
SD8
Delayed
SDCLK
SD10
SDDATA
form
Memories
WD1
NOTE: Data driven from memories relative
to delayed memory clock.
WD2
WD3
WD4
SD11
Figure 9. SDR Read Timing
9.2
DDR SDRAM AC Timing Characteristics
When using the DDR SDRAM controller, the following timing numbers must be followed to properly
latch or drive data onto the memory bus. All timing numbers are relative to the four DQS byte lanes.
Table 12shows the DDR clock crossover specifications.
Table 12. DDR Clock Crossover Specifications
Symbol
Characteristic
Min
Max
Unit
VMP
Clock output mid-point voltage
1.05
1.45
V
VOUT
Clock output voltage level
–0.3
SD_VDD + 0.3
V
VID
Clock output differential voltage (peak to peak swing)
0.7
SD_VDD + 0.6
V
1.05
1.45
V
VIX
Clock crossing point
voltage1
NOTES:
1 The clock crossover voltage is only guaranteed when using the highest drive strength option for the
SDCLK[1:0] and SDCLK[1:0] signals.
MCF547x Integrated Microprocessor Electrical Characteristics, Rev. 2
14
Freescale Semiconductor
SDRAM Bus
SDCLK
VIX
VMP
VIX
VID
SDCLK
Figure 10. DDR Clock Timing Diagram
Table 13. DDR Timing Specifications
Symbol
Characteristic
Frequency of Operation
Min
Max
Unit
Notes
83
133
MHz
1
DD1
Clock Period (tCK)
7.52
12
ns
2
DD2
Pulse Width High (tCKH)
0.45
0.55
SDCLK
3
DD3
Pulse Width Low (tCKL)
0.45
0.55
SDCLK
4
DD4
Address, SDCKE, CAS, RAS, WE, SDBA, SDCS—Output
Valid (tCMV)
—
0.5 × SDCLK
+ 1.0 ns
ns
5
DD5
Address, SDCKE, CAS, RAS, WE, SDBA, SDCS—Output Hold
(tCMH)
2.0
—
ns
DD6
Write Command to first DQS Latching Transition (tDQSS)
—
1.25
SDCLK
DD7
Data and Data Mask Output Setup (DQ−>DQS) Relative to
DQS (DDR Write Mode) (tQS)
1.0
—
ns
DD8
Data and Data Mask Output Hold (DQS−>DQ) Relative to DQS
(DDR Write Mode) (tQH)
1.0
DD9
Input Data Skew Relative to DQS (Input Setup) (tIS)
DD10
Input Data Hold Relative to DQS (tIH)
DD11
6
7
—
ns
8
1
ns
9
0.25 × SDCLK
+ 0.5ns
—
ns
10
DQS falling edge to SDCLK rising (output setup time) (tDSS)
0.5
—
ns
DD12
DQS falling edge from SDCLK rising (output hold time) (tDSH)
0.5
—
ns
DD13
DQS input read preamble width (tRPRE)
0.9
1.1
SDCLK
DD14
DQS input read postamble width (tRPST)
0.4
0.6
SDCLK
DD15
DQS output write preamble width (tWPRE)
0.25
—
SDCLK
DD16
DQS output write postamble width (tWPST)
0.4
0.6
SDCLK
NOTES:
1 The frequency of operation is either 2x or 4x the CLKIN frequency of operation. The MCF547X supports a single external
reference clock (CLKIN). This signal defines the frequency of operation for both FlexBus and PCI, but SDRAM clock
operates at the same frequency as the internal bus clock. Please see Section 2.2.6, “Reset Configuration Pins.”
2 SDCLK is one memory clock in (ns).
3
Pulse width high plus pulse width low cannot exceed max clock period.
4
Pulse width high plus pulse width low cannot exceed max clock period.
5 Command output valid should be 1/2 the memory bus clock (SDCLK) plus some minor adjustments for process,
temperature, and voltage variations.
6 This specification relates to the required input setup time of today’s DDR memories. SDDATA[31:24] is relative to
SDDQS3, SDDATA[23:16] is relative to SDDQS2, SDDATA[15:8] is relative to SDDQS1, and SDDATA[7:0] is relative
SDDQS0.
7
The first data beat will be valid before the first rising edge of SDDQS and after the SDDQS write preamble. The remaining
data beats will be valid for each subsequent SDDQS edge.
MCF547x Integrated Microprocessor Electrical Characteristics, Rev. 2
Freescale Semiconductor
15
SDRAM Bus
8
This specification relates to the required hold time of today’s DDR memories. SDDATA[31:24] is relative to SDDQS3,
SDDATA[23:16] is relative to SDDQS2, SDDATA[15:8] is relative to SDDQS1, and SDDATA[7:0] is relative SDDQS0.
9
Data input skew is derived from each SDDQS clock edge. It begins with a SDDQS transition and ends when the last data
line becomes valid. This input skew must include DDR memory output skew and system level board skew (due to routing
or other factors).
10 Data input hold is derived from each SDDQS clock edge. It begins with a SDDQS transition and ends when the first data
line becomes invalid.
DD1
DD2
SDCLK0
DD3
SDCLK1
SDCLK0
SDCLK1
DD5
SDCSn,SDWE,
RAS, CAS
CMD
DD4
SDADDR,
SDBA[1:0]
DD6
ROW
COL
DD7
SDDM
DD8
SDDQS
DD7
SDDATA
WD1 WD2 WD3 WD4
DD8
Figure 11. DDR Write Timing
MCF547x Integrated Microprocessor Electrical Characteristics, Rev. 2
16
Freescale Semiconductor
PCI Bus
DD1
DD2
SDCLK0
DD3
SDCLK1
SDCLK0
SDCLK1
CL=2
DD5
SDCSn,SDWE,
RAS, CAS
CMD
CL=2.5
DD4
SDADDR,
SDBA[1:0]
ROW
COL
DQS Read
Preamble
SDDQS
DD9
DQS Read
Postamble
DD10
SDDATA
WD1 WD2 WD3 WD4
DQS Read
DQS Read
Preamble
Postamble
SDDQS
WD1 WD2 WD3 WD4
SDDATA
Figure 12. DDR Read Timing
10
PCI Bus
The PCI bus on the MCF547x is PCI 2.2 compliant. The following timing numbers are mostly from the
PCI 2.2 spec. Please refer to the PCI 2.2 spec for a more detailed timing analysis.
Table 14. PCI Timing Specifications
Num
Characteristic
Frequency of Operation
Min
Max
Unit
Notes
30
66
MHz
1
15.15
33.33
ns
2
P1
Clock Period (tCK)
P2
Address, Data, and Command (33< PCI ≤ 66 Mhz)—Input Setup (tIS)
3.0
—
ns
P3
Address, Data, and Command (0 < PCI ≤ 33 Mhz)—Input Setup (tIS)
7.0
—
ns
P4
Address, Data, and Command (33-66 Mhz) - Output Valid (tDV)
—
6.0
ns
P5
Address, Data, and Command (0 -33 Mhz) - Output Valid (tDV)
—
11.0
ns
3
MCF547x Integrated Microprocessor Electrical Characteristics, Rev. 2
Freescale Semiconductor
17
Fast Ethernet AC Timing Specifications
Table 14. PCI Timing Specifications (continued)
Num
Characteristic
Min
Max
Unit
Notes
4
P6
PCI signals (0 - 66 Mhz) - Output Hold (tDH)
0
—
ns
P7
PCI signals (0 - 66 Mhz) - Input Hold (tIH)
0
—
ns
5
P8
PCI REQ/GNT (33 < PCI ≤ 66Mhz) - Output valid (tDV)
—
6
ns
6
P9
PCI REQ/GNT (0 < PCI ≤ 33Mhz) - Output valid (tDV)
—
12
ns
P10
PCI REQ/GNT (33 < PCI ≤ 66Mhz) - Input Setup (tIS)
—
5
ns
P11
PCI REQ (0 < PCI ≤ 33Mhz) - Input Setup (tIS)
12
—
ns
P12
PCI GNT (0 < PCI ≤ 33Mhz) - Input Setup (tIS)
10
—
ns
NOTES:
Please see Section 2.2.6, “Reset Configuration Pins,” for more information on setting the PCI clock rate. Also
specific guidelines may need to be followed when operating the system PLL below certain frequencies.
2 Max cycle rate is determined by CLKIN and how the user has the system PLL configured.
3
All signals defined as PCI bused signals. Does not include PTP (point-to-point) signals.
4 PCI 2.2 spec does not require an output hold time. Although the MCF547X may provide a slight amount of hold, it
is not required or guaranteed.
5 PCI 2.2 spec requires zero input hold.
6 These signals are defined at PTP (Point-to-point) in the PCI 2.2 spec.
1
P1
CLKIN
P4
Output
Valid/Hold
P6
Output Valid
P2
Input
Setup/Hold
Input Valid
P7
Figure 13. PCI Timing
11
Fast Ethernet AC Timing Specifications
11.1 MII/7-WIRE Interface Timing Specs
The following timing specs are defined at the chip I/O pin and must be translated appropriately to arrive
at timing specs/constraints for the EMAC_10_100 I/O signals.
The following timing specs meet the requirements for both MII and 7-Wire style interfaces for a range of
transceiver devices. If this interface is to be used with a specific transceiver device the timing specs may
be altered to match that specific transceiver.
MCF547x Integrated Microprocessor Electrical Characteristics, Rev. 2
18
Freescale Semiconductor
Fast Ethernet AC Timing Specifications
Table 15. MII Receive Signal Timing
Num
Characteristic
Min
Max
Unit
M1
RXD[3:0], RXDV, RXER to RXCLK setup
5
—
ns
M2
RXCLK to RXD[3:0], RXDV, RXER hold
5
—
ns
M3
RXCLK pulse width high
35%
65%
RXCLK period
M4
RXCLK pulse width low
35%
65%
RXCLK period
Min
Max
Unit
M3
RXCLK (Input)
M1
M4
RXD[3:0] (Inputs)
RXDV,
RXER
M2
Figure 14. MII Receive Signal Timing Diagram
11.2 MII Transmit Signal Timing
Table 16. MII Transmit Signal Timing
Num
Characteristic
M5
TXCLK to TXD[3:0], TXEN, TXER invalid
0
—
ns
M6
TXCLK to TXD[3:0], TXEN, TXER valid
—
25
ns
M7
TXCLK pulse width high
35%
65%
TXCLK period
M8
TXCLK pulse width low
35%
65%
TXCLK period
M7
TXCLK (Input)
M5
M8
TXD[3:0] (Outputs)
TXEN,
TXER
M6
Figure 15. MII Transmit Signal Timing Diagram
MCF547x Integrated Microprocessor Electrical Characteristics, Rev. 2
Freescale Semiconductor
19
Fast Ethernet AC Timing Specifications
11.3 MII Async Inputs Signal Timing (CRS, COL)
Table 17. MII Transmit Signal Timing
Num
M9
Characteristic
CRS, COL minimum pulse width
Min
Max
Unit
1.5
—
TX_CLK period
CRS, COL
M9
Figure 16. MII Async Inputs Timing Diagram
11.4 MII Serial Management Channel Timing (MDIO,MDC)
Table 18. MII Serial Management Channel Signal Timing
Num
Characteristic
Min
Max
Unit
M10
MDC falling edge to MDIO output invalid
(min prop delay)
0
—
ns
M11
MDC falling edge to MDIO output valid
(max prop delay)
—
25
ns
M12
MDIO (input) to MDC rising edge setup
10
—
ns
M13
MDIO (input) to MDC rising edge hold
0
—
ns
M14
MDC pulse width high
40%
60%
MDC period
M15
MDC pulse width low
40%
60%
MDC period
M14
M15
MDC (Output)
M10
MDIO (Output)
M12
M11
MDIO (Input)
M13
Figure 17. MII Serial Management Channel TIming Diagram
MCF547x Integrated Microprocessor Electrical Characteristics, Rev. 2
20
Freescale Semiconductor
General Timing Specifications
12
General Timing Specifications
Table 19 lists timing specifications for the GPIO, PSC, DREQ, DACK, and external interrupts.
Table 19. General AC Timing Specifications
Name
Characteristic
Min
Max
Unit
G1
CLKIN high to signal output valid
—
2
PSTCLK
G2
CLKIN high to signal invalid (output hold)
0
—
ns
G3
Signal input pulse width
2
—
PSTCLK
13
I2C Input/Output Timing Specifications
Table 20 lists specifications for the I2C input timing parameters shown in Figure 18.
Table 20. I2C Input Timing Specifications between SCL and SDA
Num
Characteristic
Min
Max
Units
I1
Start condition hold time
2
—
Bus clocks
I2
Clock low period
8
—
Bus clocks
I3
SCL/SDA rise time (VIL = 0.5 V to VIH = 2.4 V)
—
1
mS
I4
Data hold time
0
—
ns
I5
SCL/SDA fall time (VIH = 2.4 V to VIL = 0.5 V)
—
1
mS
I6
Clock high time
4
—
Bus clocks
I7
Data setup time
0
—
ns
I8
Start condition setup time (for repeated start condition only)
2
—
Bus clocks
I9
Stop condition setup time
2
—
Bus clocks
Table 21 lists specifications for the I2C output timing parameters shown in Figure 18.
MCF547x Integrated Microprocessor Electrical Characteristics, Rev. 2
Freescale Semiconductor
21
I2C Input/Output Timing Specifications
Table 21. I2C Output Timing Specifications between SCL and SDA
Num
Characteristic
Min
Max
Units
I11
Start condition hold time
6
—
Bus clocks
I2 1
Clock low period
10
—
Bus clocks
I3
2
SCL/SDA rise time (VIL = 0.5 V to VIH = 2.4 V)
—
—
µS
I4
1
Data hold time
7
—
Bus clocks
I5
3
SCL/SDA fall time (VIH = 2.4 V to VIL = 0.5 V)
—
3
ns
I6
1
Clock high time
10
—
Bus clocks
I7
1
Data setup time
2
—
Bus clocks
I8
1
Start condition setup time (for repeated start
condition only)
20
—
Bus clocks
Stop condition setup time
10
—
Bus clocks
I9 1
NOTES:
1
Note: Output numbers depend on the value programmed into the IFDR; an IFDR programmed
with the maximum frequency (IFDR = 0x20) results in minimum output timings as shown in
Table 21. The I2C interface is designed to scale the actual data transition time to move it to the
middle of the SCL low period. The actual position is affected by the prescale and division values
programmed into the IFDR; however, the numbers given in Table 21 are minimum values.
2 Because SCL and SDA are open-collector-type outputs, which the processor can only actively
drive low, the time SCL or SDA take to reach a high level depends on external signal
capacitance and pull-up resistor values.
3
Specified at a nominal 50-pF load.
Figure 18 shows timing for the values in Table 20 and Table 21.
I2
I6
I5
SCL
I1
I3
I7
I4
I8
I9
SDA
Figure 18. I2C Input/Output Timings
MCF547x Integrated Microprocessor Electrical Characteristics, Rev. 2
22
Freescale Semiconductor
JTAG and Boundary Scan Timing
14
JTAG and Boundary Scan Timing
Table 22. JTAG and Boundary Scan Timing
Characteristics1
Num
Symbol
Min
Max
Unit
J1
TCLK Frequency of Operation
fJCYC
DC
10
MHz
J2
TCLK Cycle Period
tJCYC
2
—
tCK
J3
TCLK Clock Pulse Width
tJCW
15.15
—
ns
J4
TCLK Rise and Fall Times
tJCRF
0.0
3.0
ns
J5
Boundary Scan Input Data Setup Time to TCLK Rise
tBSDST
5.0
—
ns
J6
Boundary Scan Input Data Hold Time after TCLK Rise
tBSDHT
24.0
—
ns
J7
TCLK Low to Boundary Scan Output Data Valid
tBSDV
0.0
15.0
ns
J8
TCLK Low to Boundary Scan Output High Z
tBSDZ
0.0
15.0
ns
J9
TMS, TDI Input Data Setup Time to TCLK Rise
tTAPBST
5.0
—
ns
J10
TMS, TDI Input Data Hold Time after TCLK Rise
tTAPBHT
10.0
—
ns
J11
TCLK Low to TDO Data Valid
tTDODV
0.0
15.0
ns
J12
TCLK Low to TDO High Z
tTDODZ
0.0
15.0
ns
J13
TRST Assert Time
tTRSTAT
100.0
—
ns
J14
TRST Setup Time (Negation) to TCLK High
tTRSTST
10.0
—
ns
NOTES:
1 MTMOD is expected to be a static signal. Hence, it is not associated with any timing
J2
J3
TCLK (Input)
J3
VIH
VIL
J4
J4
Figure 19. Test Clock Input Timing
MCF547x Integrated Microprocessor Electrical Characteristics, Rev. 2
Freescale Semiconductor
23
JTAG and Boundary Scan Timing
TCLK
VIH
VIL
5
Data Inputs
6
Input Data Valid
7
Output Data Valid
Data Outputs
8
Data Outputs
7
Data Outputs
Output Data Valid
Figure 20. Boundary Scan (JTAG) Timing
TCLK
VIH
VIL
9
TDI, TMS, BKPT
10
Input Data Valid
11
TDO
Output Data Valid
12
TDO
11
TDO
Output Data Valid
Figure 21. Test Access Port Timing
TCLK
14
TRST
13
Figure 22. TRST Timing Debug AC Timing Specifications
MCF547x Integrated Microprocessor Electrical Characteristics, Rev. 2
24
Freescale Semiconductor
JTAG and Boundary Scan Timing
Table 23 lists specifications for the debug AC timing parameters shown in Figure 24.
Table 23. Debug AC Timing Specification
66 MHz
Num
Characteristic
Units
Min
Max
D1
PSTDDATA to PSTCLK setup
4.5
ns
D2
PSTCLK to PSTDDATA hold
4.5
ns
D3
DSI-to-DSCLK setup
1
PSTCLKs
D4 1
DSCLK-to-DSO hold
4
PSTCLKs
DSCLK cycle time
5
PSTCLKs
D5
NOTES:
1
DSCLK and DSI are synchronized internally. D4 is measured from the
synchronized DSCLK input relative to the rising edge of CLKOUT.
Figure 23 shows real-time trace timing for the values in Table 23.
PSTCLK
D1
D2
PSTDDATA[7:0]
Figure 23. Real-Time Trace AC Timing
Figure 24 shows BDM serial port AC timing for the values in Table 23.
D5
DSCLK
D3
DSI
Current
Next
D4
DSO
Past
Current
Figure 24. BDM Serial Port AC Timing
MCF547x Integrated Microprocessor Electrical Characteristics, Rev. 2
Freescale Semiconductor
25
DSPI Electrical Specifications
15
DSPI Electrical Specifications
Table 24 lists DSPI timings.
Table 24. DSPI Modules AC Timing Specifications
Name
Characteristic
Min
Max
Unit
1 × tck
510 × tck
ns
DS1
DSPI_CS[3:0] to DSPI_CLK
DS2
DSPI_CLK high to DSPI_DOUT valid.
—
12
ns
DS3
DSPI_CLK high to DSPI_DOUT invalid. (Output hold)
2
—
ns
DS4
DSPI_DIN to DSPI_CLK (Input setup)
10
—
ns
DS5
DSPI_DIN to DSPI_CLK (Input hold)
10
—
ns
The values in Table 24 correspond to Figure 25.
DSPI_CS[3:0]
DS1
DSPI_CLK
DS2
DSPI_DOUT
DS3
DS4
DS5
DSPI_DIN
Figure 25. DSPI Timing
16
Timer Module AC Timing Specifications
Table 25 lists timer module AC timings.
Table 25. Timer Module AC Timing Specifications
0–66 MHz
Name
Characteristic
Unit
Min
Max
T1
TIN0 / TIN1 / TIN2 / TIN3 cycle time
3
—
PSTCLK
T2
TIN0 / TIN1 / TIN2 / TIN3 pulse width
1
—
PSTCLK
MCF547x Integrated Microprocessor Electrical Characteristics, Rev. 2
26
Freescale Semiconductor
THIS PAGE INTENTIONALLY LEFT BLANK
MCF547x Integrated Microprocessor Electrical Characteristics, Rev. 2
Freescale Semiconductor
27
How to Reach Us:
Home Page:
www.freescale.com
E-mail:
[email protected]
USA/Europe or Locations Not Listed:
Freescale Semiconductor
Technical Information Center, CH370
1300 N. Alma School Road
Chandler, Arizona 85224
+1-800-521-6274 or +1-480-768-2130
[email protected]
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
[email protected]
Japan:
Freescale Semiconductor Japan Ltd.
Technical Information Center
3-20-1, Minami-Azabu, Minato-ku
Tokyo 106-0047, Japan
0120 191014 or +81 3 3440 3569
[email protected]
Asia/Pacific:
Freescale Semiconductor Hong Kong Ltd.
Technical Information Center
2 Dai King Street
Tai Po Industrial Estate
Tai Po, N.T., Hong Kong
+800 2666 8080
[email protected]
For Literature Requests Only:
Freescale Semiconductor Literature Distribution Center
P.O. Box 5405
Denver, Colorado 80217
1-800-441-2447 or 303-675-2140
Fax: 303-675-2150
[email protected]
Information in this document is provided solely to enable system and
software implementers to use Freescale Semiconductor products. There are
no express or implied copyright licenses granted hereunder to design or
fabricate any integrated circuits or integrated circuits based on the
information in this document.
Freescale Semiconductor reserves the right to make changes without further
notice to any products herein. Freescale Semiconductor makes no warranty,
representation or guarantee regarding the suitability of its products for any
particular purpose, nor does Freescale Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation consequential or
incidental damages. “Typical” parameters that may be provided in Freescale
Semiconductor data sheets and/or specifications can and do vary in different
applications and actual performance may vary over time. All operating
parameters, including “Typicals”, must be validated for each customer
application by customer’s technical experts. Freescale Semiconductor does
not convey any license under its patent rights nor the rights of others.
Freescale Semiconductor products are not designed, intended, or authorized
for use as components in systems intended for surgical implant into the body,
or other applications intended to support or sustain life, or for any other
application in which the failure of the Freescale Semiconductor product could
create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended
or unauthorized application, Buyer shall indemnify and hold Freescale
Semiconductor and its officers, employees, subsidiaries, affiliates, and
distributors harmless against all claims, costs, damages, and expenses, and
reasonable attorney fees arising out of, directly or indirectly, any claim of
personal injury or death associated with such unintended or unauthorized
use, even if such claim alleges that Freescale Semiconductor was negligent
regarding the design or manufacture of the part.
Freescale™ and the Freescale logo are trademarks of Freescale
Semiconductor, Inc. All other product or service names are the property
of their respective owners.© Freescale Semiconductor, Inc. 2004. All rights
reserved.
MCF5475EC
Rev. 2
10/2004
Similar pages