AD AD7863ARS-2REEL7 Simultaneous sampling dual 175 ksps 14-bit adc Datasheet

Simultaneous Sampling
Dual 175 kSPS 14-Bit ADC
AD7863
FUNCTIONAL BLOCK DIAGRAM
FEATURES
VREF
VA1
VB1
VA2
VB2
SIGNAL
SCALING
MUX
TRACK/
HOLD
SIGNAL
SCALING
TRACK/
HOLD
SIGNAL
SCALING
SIGNAL
SCALING
MUX
14-BIT
ADC
OUTPUT
LATCH
14-BIT
ADC
DB0
DB13
CS
RD
CONVERSION
CONTROL LOGIC
A0
BUSY CONVST
CLOCK
AGND
AGND
DGND
Figure 1.
The AD7863 is a high speed, low power, dual 14-bit analog-todigital converter that operates from a single 5 V supply.
A single conversion start signal (CONVST) simultaneously places
both track/holds into hold and initiates conversion on both
channels. The BUSY signal indicates the end of conversion and at
this time the conversion results for both channels are available to be
read. The first read after a conversion accesses the result from VA1
or VB1, and the second read accesses the result from VA2 or VB2,
depending on whether the multiplexer select (A0) is low or high,
respectively. Data is read from the part via a 14-bit parallel data bus
with standard CS and RD signals. In addition to the traditional dc
accuracy specifications such as linearity, gain, and offset errors, the
part is also specified for dynamic performance parameters
including harmonic distortion and signal-to-noise ratio.
2.5V
REFERENCE
AD7863
GENERAL DESCRIPTION
The part contains two 5.2 μs successive approximation ADCs, two
track/hold amplifiers, an internal 2.5 V reference and a high speed
parallel interface. Four analog inputs are grouped into two channels
(A and B) selected by the A0 input. Each channel has two inputs
(VA1 and VA2 or VB1 and VB2) that can be sampled and converted
simultaneously, thus preserving the relative phase information of
the signals on both analog inputs. The part accepts an analog input
range of ±10 V (AD7863-10), ±2.5 V (AD7863-3), and 0 V to
2.5 V (AD7863-2). Overvoltage protection on the analog inputs
for the part allows the input voltage to go to ±17 V, ±7 V, or +7 V
respectively, without causing damage.
VDD
2kΩ
06411-001
Two fast 14-bit ADCs
Four input channels
Simultaneous sampling and conversion
5.2 μs conversion time
Single supply operation
Selection of input ranges
±10 V for AD7863-10
±2.5 V for AD7863-3
0 V to 2.5 V for AD7863-2
High speed parallel interface
Low power, 70 mW typical
Power saving mode, 105 μW maximum
Overvoltage protection on analog inputs
14-bit lead compatible upgrade to AD7862
process that combines precision bipolar circuits with low power
CMOS logic. It is available in 28-lead SOIC_W and SSOP.
PRODUCT HIGHLIGHTS
1.
2.
3.
4.
5.
The AD7863 features two complete ADC functions
allowing simultaneous sampling and conversion of two
channels. Each ADC has a two-channel input mux. The
conversion result for both channels is available 5.2 μs after
initiating conversion.
The AD7863 operates from a single 5 V supply and
consumes 70 mW typical. The automatic power-down
mode, where the part goes into power-down once
conversion is complete and wakes up before the next
conversion cycle, makes the AD7863 ideal for batterypowered or portable applications.
The part offers a high speed parallel interface for easy
connection to microprocessors, microcontrollers, and
digital signal processors.
The part is offered in three versions with different analog
input ranges. The AD7863-10 offers the standard industrial
input range of ±10 V; the AD7863-3 offers the common
signal processing input range of ±2.5 V, while the AD7863-2
can be used in unipolar 0 V to 2.5 V applications.
The part features very tight aperture delay matching
between the two input sample and hold amplifiers.
The AD7863 is fabricated in the Analog Devices, Inc. linear
compatible CMOS (LC2MOS) process, a mixed technology
Rev. B
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2006 Analog Devices, Inc. All rights reserved.
AD7863* PRODUCT PAGE QUICK LINKS
Last Content Update: 02/23/2017
COMPARABLE PARTS
DISCUSSIONS
View a parametric search of comparable parts.
View all AD7863 EngineerZone Discussions.
DOCUMENTATION
SAMPLE AND BUY
Data Sheet
Visit the product page to see pricing options.
• AD7863: Simultaneous Sampling Dual 175 kSPS 14-Bit
ADC Data Sheet
TECHNICAL SUPPORT
REFERENCE MATERIALS
Submit a technical question or find your regional support
number.
Technical Articles
• MS-2210: Designing Power Supplies for High Speed ADC
DOCUMENT FEEDBACK
Submit feedback for this data sheet.
DESIGN RESOURCES
• AD7863 Material Declaration
• PCN-PDN Information
• Quality And Reliability
• Symbols and Footprints
This page is dynamically generated by Analog Devices, Inc., and inserted into this data sheet. A dynamic change to the content on this page will not
trigger a change to either the revision number or the content of the product data sheet. This dynamic page may be frequently modified.
AD7863
TABLE OF CONTENTS
Features .............................................................................................. 1
Effective Number of Bits ........................................................... 14
General Description ......................................................................... 1
Total Harmonic Distortion (THD) .......................................... 15
Functional Block Diagram .............................................................. 1
Intermodulation Distortion ...................................................... 15
Product Highlights ........................................................................... 1
Peak Harmonic or Spurious Noise........................................... 15
Revision History ............................................................................... 2
DC Linearity Plot ....................................................................... 15
Specifications..................................................................................... 3
Power Considerations................................................................ 16
Timing Characteristics ................................................................ 5
Microprocessor Interfacing........................................................... 17
Absolute Maximum Ratings............................................................ 6
AD7863 to ADSP-2100 Interface ............................................. 17
ESD Caution.................................................................................. 6
AD7863 to ADSP-2101/ADSP-2102 Interface ....................... 17
Pin Configuration and Function Descriptions............................. 7
AD7863 to TMS32010 Interface .............................................. 17
Terminology ...................................................................................... 8
AD7863 to TMS320C25 Interface............................................ 17
Converter Details.............................................................................. 9
AD7863 to MC68000 Interface ................................................ 18
Track-and-Hold Section .............................................................. 9
AD7863 to 80C196 Interface .................................................... 18
Reference Section ......................................................................... 9
Vector Motor Control ................................................................ 18
Circuit Description......................................................................... 10
Multiple AD7863s ...................................................................... 19
Analog Input Section ................................................................. 10
Applications Hints.......................................................................... 20
Offset and Full-Scale Adjustment ............................................ 10
PC Board Layout Considerations............................................. 20
Timing and Control ................................................................... 11
Ground Planes ............................................................................ 20
Operating Modes ............................................................................ 13
Power Planes ............................................................................... 20
Mode 1 Operation ...................................................................... 13
Supply Decoupling ..................................................................... 20
Mode 2 Operation ...................................................................... 13
Outline Dimensions ....................................................................... 21
AD7863 Dynamic Specifications ............................................. 14
Ordering Guide .......................................................................... 22
Signal-to-Noise Ratio (SNR)..................................................... 14
REVISION HISTORY
11/06—Rev. A to Rev. B
Updated Format..................................................................Universal
Deleted Applications ........................................................................ 1
Changes to Specifications ................................................................ 3
Changes to Absolute Maximum Ratings ....................................... 6
Updated Outline Dimensions ....................................................... 21
Changes to Ordering Guide .......................................................... 22
5/99—Rev. 0 to Rev. A
Rev. B | Page 2 of 24
AD7863
SPECIFICATIONS
VDD = 5 V ± 5%, AGND = DGND = 0 V, REF = Internal. All specifications TMIN to TMAX, unless otherwise noted.
Table 1.
Parameter
SAMPLE AND HOLD
−3 dB Small Signal Bandwidth
Aperture Delay 2
Aperture Jitter2
Aperture Delay Matching2
DYNAMIC PERFORMANCE 3
Signal-to-(Noise + Distortion) Ratio 4
@ 25°C
TMIN to TMAX
Total Harmonic Distortion4
Peak Harmonic or Spurious Noise4
Intermodulation Distortion4
Second Order Terms
Third Order Terms
Channel-to-Channel Isolation4
DC ACCURACY
Resolution
Minimum Resolution for Which No
Missing Codes are Guaranteed
Relative Accuracy4
Differential Nonlinearity4
AD7863-10, AD7863-3
Positive Gain Error4
Positive Gain Error Match4
Negative Gain Error4
Negative Gain Error Match4
Bipolar Zero Error
Bipolar Zero Error Match
AD7863-2
Positive Gain Error4
Positive Gain Error Match4
Unipolar Offset Error
Unipolar Offset Error Match
ANALOG INPUTS
AD7863-10
Input Voltage Range
Input Resistance
AD7863-3
Input Voltage Range
Input Resistance
AD7863-2
Input Voltage Range
Input Current
A Version 1
B Version1
Unit
7
35
50
350
7
35
50
350
MHz typ
ns max
ps typ
ps max
Test Conditions/Comments
fIN = 80.0 kHz, fS = 175 kSPS
78
77
−82
−82
78
77
−82
−82
dB min
dB min
dB max
dB max
−93
−89
−86
−93
−89
−86
dB typ
dB typ
dB typ
14
14
Bits
14
±2.5
+2 to −1
14
±2
+2 to −1
Bits
LSB max
LSB max
±10
10
±10
10
±10
8
±8
10
±8
10
±8
6
LSB max
LSB max
LSB max
LSB max
LSB max
LSB max
±14
16
±14
10
LSB max
LSB max
LSB max
LSB max
±10
9
±10
9
V
kΩ typ
±2.5
3
±2.5
3
V
kΩ typ
2.5
100
2.5
100
V
nA max
Rev. B | Page 3 of 24
−87 dB typ
−90 dB typ
fa = 49 kHz, fb = 50 kHz
fIN = 50 kHz sine wave
Any channel
AD7863
Parameter
REFERENCE INPUT/OUTPUT
REF IN Input Voltage Range
REF IN Input Current
REF OUT Output Voltage
REF OUT Error @ 25°C
REF OUT Error TMIN to TMAX
REF OUT Temperature Coefficient
LOGIC INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IIN
Input Capacitance, CIN 5
LOGIC OUTPUTS
Output High Voltage, VOH
Output Low Voltage, VOL
DB11 to DB0
Floating-State Leakage Current
Floating-State Capacitance5
Output Coding
AD7863-10, AD7863-3
AD7863-2
CONVERSION RATE
Conversion Time
Mode 1 Operation
Mode 2 Operation 6
Track/Hold Acquisition Time4, 7
POWER REQUIREMENTS
VDD
IDD
Normal Mode (Mode 1)
AD7863-10
AD7863-3
AD7863-2
Power-Down Mode (Mode 2)
IDD @ 25°C 8
Power Dissipation
Normal Mode (Mode 1)
AD7863-10
AD7863-3
AD7863-2
Power-Down Mode @ 25°C
A Version 1
B Version1
Unit
Test Conditions/Comments
2.375 to 2.625
±100
2.5
±10
±20
25
2.375 to 2.625
±100
2.5
±10
±20
25
V
μA max
V nom
mV max
mV max
ppm/°C typ
2.5 V ± 5%
2.4
0.8
±10
10
2.4
0.8
±10
10
V min
V max
μA max
pF max
VDD = 5 V ± 5%
VDD = 5 V ± 5%
4.0
0.4
4.0
0.4
V min
V max
ISOURCE = 200 μA
ISINK = 1.6 mA
±10
10
±10
10
μA max
pF max
Twos complement
Straight (natural) binary
5.2
10.0
0.5
5.2
10.0
0.5
μs max
μs max
μs max
For both channels
For both channels
5
5
V nom
±5% for specified performance
18
16
11
18
16
11
mA max
mA max
mA max
20
20
μA max
40 nA typ. Logic inputs = 0 V or VDD
94.50
84
57.75
105
94.50
84
57.75
105
mW max
mW max
mW max
μW max
VDD = 5.25 V, 70 mW typ
VDD = 5.25 V, 70 mW typ
VDD = 5.25 V, 45 mW typ
210 nW typ, VDD = 5.25 V
1
Temperature ranges are as follows: A Version and B Version, −40°C to +85°C.
Sample tested during initial release.
Applies to Mode 1 operation. See Operating Modes section.
4
See Terminology section.
5
Sample tested @ 25°C to ensure compliance.
6
This 10 μs includes the wake-up time from standby. This wake-up time is timed from the rising edge of CONVST, whereas conversion is timed from the falling edge of
CONVST, for a narrow CONVST pulse width the conversion time is effectively the wake-up time plus conversion time, 10 μs. This can be seen from Figure 6. Note that if
the CONVST pulse width is greater than 5.2 μs, the effective conversion time increases beyond 10 μs.
7
Performance measured through full channel (multiplexer, SHA, and ADC).
8
For best dynamic performance of the AD7863, ATE device testing has to be performed with power supply decoupling in place. In the AD7863 power-down mode of
operation, the leakage current associated with these decoupling capacitors is greater than that of the AD7863 supply current. Therefore, the 40 nA typical figure
shown is characterized and guaranteed by design figure, which reflects the supply current of the AD7863 without decoupling in place. The maximum figure shown in
the Conditions/Comments column reflects the AD7863 with supply decoupling in place—0.1 μF in parallel with 10 μF disc ceramic capacitors on the VDD pin and
2 × 0.1 μF disc ceramic capacitors on the VREF pin, in both cases to the AGND plane.
2
3
Rev. B | Page 4 of 24
AD7863
TIMING CHARACTERISTICS
VDD = 5 V ± 5%, AGND = DGND = 0 V, REF = Internal. All specifications TMIN to TMAX, unless otherwise noted.
Table 2.
Parameter 1, 2
tCONV
tACQ
Parallel Interface
t1
t2
t3
t4
t5 3
t6 4
t7
t8
A, B Versions
5.2
0.5
Unit
μs max
μs max
Test Conditions/Comments
Conversion time
Acquisition time
0
0
35
45
30
5
30
10
400
ns min
ns min
ns min
ns min
ns min
ns min
ns max
ns min
ns min
CS to RD setup time
CS to RD hold time
CONVST pulse width
RD pulse width
Data access time after falling edge of RD
Bus relinquish time after rising edge of RD
Time between consecutive reads
Quiet time
1
Sample tested at 25°C to ensure compliance. All input signals are measured with tr = tf = 1 ns (10% to 90% of 5 V) and timed from a voltage level of 1.6 V.
See Figure 2.
3
Measured with the load circuit of Figure 3 and defined as the time required for an output to cross 0.8 V or 2.0 V.
4
These times are derived from the measured time taken by the data outputs to change 0.5 V when loaded with the circuit of Figure 3. The measured number is then
extrapolated back to remove the effects of charging or discharging the 50 pF capacitor. This means that the times quoted in the timing characteristics are the true bus
relinquish times of the part and as such are independent of external bus loading capacitances.
2
tACQ
t8
CONVST
t3
BUSY
tCONV = 5.2µs
A0
CS
t1
t7
t2
t4
RD
t5
VA2
VB1
Figure 2. Timing Diagram
1.6mA
TO OUTPUT
PIN
50pF
200µA
Figure 3. Load Circuit for Access Time and Bus Relinquish Time
Rev. B | Page 5 of 24
VB2
06411-002
VA1
06411-003
DATA
t6
AD7863
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 3.
Parameter
VDD to AGND
VDD to DGND
Analog Input Voltage to AGND
AD7863-10
AD7863-3
AD7863-2
Reference Input Voltage to AGND
Digital Input Voltage to DGND
Digital Output Voltage to DGND
Operating Temperature Range
Commercial (A Version and B Version)
Storage Temperature Range
Junction Temperature
SOIC Package, Power Dissipation
θJA Thermal Impedance
θJC Thermal Impedance
Lead Temperature, Soldering
Vapor Phase (60 sec)
Infrared (15 sec)
SSOP Package, Power Dissipation
θJA Thermal Impedance
θJC Thermal Impedance
Lead Temperature, Soldering
Vapor Phase (60 sec)
Infrared (15 sec)
Ratings
−0.3 V to +7 V
−0.3 V to +7 V
±17 V
±7 V
7V
−0.3 V to VDD + 0.3 V
−0.3 V to VDD + 0.3 V
−0.3 V to VDD + 0.3 V
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
−40°C to +85°C
−65°C to +150°C
150°C
450 mW
71.40°C/W
23.0°C/W
215°C
220°C
450 mW
109°C/W
39.0°C/W
215°C
220°C
Rev. B | Page 6 of 24
AD7863
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
DB12
1
28
DB13
DB11
2
27
AGND
DB10
3
26
VB1
DB9
4
25
VA1
DB8
5
24
VDD
DB7
6
23
BUSY
DGND
7
DB6
TOP VIEW 22 RD
8 (Not to Scale) 21 CS
A0
9
20
DB5 10
19
VREF
DB4 11
18
VA2
DB3 12
17
VB2
DB2 13
16
AGND
DB1 14
15
DB0
06411-004
CONVST
AD7863
Figure 4. Pin Configuration
Table 4. Pin Function Descriptions
Pin
No.
1 to 6
7
8
Mnemonic
DB12 to DB7
DGND
CONVST
9 to 15
16
17
DB6 to DB0
AGND
VB2
18
VA2
19
VREF
20
A0
21
22
CS
RD
23
BUSY
24
25
VDD
VA1
26
VB1
27
28
AGND
DB13
Description
Data Bit 12 to Data Bit 7. Three-state TTL outputs.
Digital Ground. Ground reference for digital circuitry.
Convert Start Input. Logic input. A high-to-low transition on this input puts both track/holds into their hold mode
and starts conversion on both channels.
Data Bit 6 to Data Bit 0. Three-state TTL outputs.
Analog Ground. Ground reference for mux, track/hold, reference, and DAC circuitry.
Input Number 2 of Channel B. Analog input voltage ranges of ±10 V (AD7863-10), ±2.5 V (AD7863-3), and 0 V to
2.5 V (AD7863-2).
Input Number 2 of Channel A. Analog input voltage ranges of ±10 V (AD7863-10), ±2.5 V (AD7863-3), and 0 V to
2.5 V (AD7863-2).
Reference Input/Output. This pin is connected to the internal reference through a series resistor and is the output
reference source for the analog-to-digital converter. The nominal reference voltage is 2.5 V, and this appears at the pin.
Multiplexer Select. This input is used in conjunction with CONVST to determine on which pair of channels the
conversion is to be performed. If A0 is low when the conversion is initiated, then channels VA1 and VA2 are
selected. If A0 is high when the conversion is initiated, channels VB1 and VB2 are selected.
Chip Select Input. Active low logic input. The device is selected when this input is active.
Read Input. Active low logic input. This input is used in conjunction with CS low to enable the data outputs and
read a conversion result from the AD7863.
Busy Output. The busy output is triggered high by the falling edge of CONVST and remains high until conversion
is completed.
Analog and Digital Positive Supply Voltage, 5.0 V ± 5%.
Input Number 1 of Channel A. Analog input voltage ranges of ±10 V (AD7863-10), ±2.5 V (AD7863-3), and 0 V to
2.5 V (AD7863-2).
Input Number 1 of Channel B. Analog input voltage ranges of ±10 V (AD7863-10), ±2.5 V (AD7863-3), and 0 V to
2.5 V (AD7863-2).
Analog Ground. Ground reference for mux, track/hold, reference, and DAC circuitry.
Data Bit 13 (MSB). Three-state TTL output. Output coding is twos complement for the AD7863-10 and AD7863-3.
Output coding is straight (natural) binary for the AD7863-2.
Rev. B | Page 7 of 24
AD7863
TERMINOLOGY
Signal-to-(Noise + Distortion) Ratio
This is the measured ratio of signal to (noise + distortion) at the
output of the analog-to-digital converter. The signal is the rms
amplitude of the fundamental. Noise is the rms sum of all nonfundamental signals up to half the sampling frequency (fS/2),
excluding dc. The ratio is dependent upon the number of
quantization levels in the digitization process; the more levels,
the smaller the quantization noise. The theoretical signal-to(noise + distortion) ratio for an ideal N-bit converter with a sine
wave input is given by
Signal to (Noise + Distortion) = (6.02N + 1.76) dB
For a 14-bit converter, this is 86.04 dB.
Total Harmonic Distortion
Total harmonic distortion (THD) is the ratio of the rms sum of
harmonics to the fundamental. For the AD7863 it is defined as
THD (dB ) = 20 log
V2 + V3 + V4 + V5
2
2
2
2
V1
where:
V1 is the rms amplitude of the fundamental.
V2, V3, V4, and V5 are the rms amplitudes of the second through
the fifth harmonics.
Peak Harmonic or Spurious Noise
Peak harmonic or spurious noise is defined as the ratio of the
rms value of the next largest component in the ADC output
spectrum (up to fS/2 and excluding dc) to the rms value of the
fundamental. Normally, the value of this specification is
determined by the largest harmonic in the spectrum, but for
parts where the harmonics are buried in the noise floor, it is
a noise peak.
Intermodulation Distortion
With inputs consisting of sine waves at two frequencies, fa and
fb, any active device with nonlinearities creates distortion
products at sum and difference frequencies of mfa ± nfb where
m, n = 0, 1, 2, 3. Intermodulation terms are those for which
neither m nor n is equal to zero. For example, the second order
terms include (fa + fb) and (fa − fb), and the third order terms
include (2fa + fb), (2fa − fb), (fa + 2fb), and (fa − 2fb).
The AD7863 is tested using two input frequencies. In this case,
the second and third order terms are of different significance.
The second order terms are usually distanced in frequency from
the original sine waves, and the third order terms are usually at
a frequency close to the input frequencies. As a result, the
second and third order terms are specified separately. The
calculation of the intermodulation distortion is as per the THD
specification where it is the ratio of the rms sum of the
individual distortion products to the rms amplitude of the
fundamental, expressed in decibels (dB).
Channel-to-Channel Isolation
Channel-to-channel isolation is a measure of the level of
crosstalk between channels. It is measured by applying a fullscale 50 kHz sine wave signal to all nonselected channels and
determining how much that signal is attenuated in the selected
channel. The figure given is the worst case across all channels.
Relative Accuracy
Relative accuracy or endpoint nonlinearity is the maximum
deviation from a straight line passing through the endpoints of
the ADC transfer function.
Differential Nonlinearity
This is the difference between the measured and the ideal 1 LSB
change between any two adjacent codes in the ADC.
Positive Gain Error (AD7863-10, ±10 V, AD7863-3, ±2.5 V)
This is the deviation of the last code transition (01 . . . 110 to
01 . . . 111) from the ideal 4 × VREF − 1 LSB (AD7863-10, ±10 V
range) or VREF − 1 LSB (AD7863-3, ±2.5 V range), after the
bipolar offset error has been adjusted out.
Positive Gain Error (AD7863-2, 0 V to 2.5 V)
This is the deviation of the last code transition (11 . . . 110 to
11 . . . 111) from the ideal VREF − 1 LSB, after the unipolar offset
error has been adjusted out.
Bipolar Zero Error (AD7863-10, ±10 V, AD7863-3, ±2.5 V)
This is the deviation of the midscale transition (all 0s to all 1s)
from the ideal 0 V (AGND).
Unipolar Offset Error (AD7863-2, 0 V to 2.5 V)
This is the deviation of the first code transition (00 . . . 000 to
00 . . . 001) from the ideal AGND + 1 LSB.
Negative Gain Error (AD7863-10, ±10 V, AD7863-3, ±2.5 V)
This is the deviation of the first code transition (10 . . . 000 to
10 . . . 001) from the ideal −4 × VREF + 1 LSB (AD7863-10, ±10 V
range) or –VREF + 1 LSB (AD7863-3, ±2.5 V range), after bipolar
zero error has been adjusted out.
Track-and-Hold Acquisition Time
Track-and-hold acquisition time is the time required for the
output of the track/hold amplifier to reach its final value, with
±½ LSB, after the end of conversion (the point at which the
track-and-hold returns to track mode). It also applies to
situations where a change in the selected input channel takes
place or where there is a step input change on the input voltage
applied to the selected VAX/BX input of the AD7863. It means
that the user must wait for the duration of the track-and-hold
acquisition time after the end of conversion or after a channel
change/step input change to VAX/BX before starting another
conversion, to ensure that the part operates to specification.
Rev. B | Page 8 of 24
AD7863
CONVERTER DETAILS
The AD7863 is a high speed, low power, dual 14-bit analog-todigital converter that operates from a single 5 V supply. The
part contains two 5.2 μs successive approximation ADCs, two
track-and-hold amplifiers, an internal 2.5 V reference, and a
high speed parallel interface. Four analog inputs are grouped
into two channels (A and B) selected by the A0 input. Each
channel has two inputs (VA1 and VA2 or VB1 and VB2) that can be
sampled and converted simultaneously, thus preserving the
relative phase information of the signals on both analog inputs.
The part accepts an analog input range of ±10 V (AD7863-10),
±2.5 V (AD7863-3), and 0 V to 2.5 V (AD7863-2). Overvoltage
protection on the analog inputs for the part allows the input
voltage to go to ±17 V, ±7 V, or +7 V, respectively, without
causing damage. The AD7863 has two operating modes, the high
sampling mode and the auto sleep mode, where the part automatically goes into sleep after the end of conversion. These modes
are discussed in more detail in the Timing and Control section.
Conversion is initiated on the AD7863 by pulsing the CONVST
input. On the falling edge of CONVST, both on-chip track-andholds are simultaneously placed into hold and the conversion
sequence is started on both channels. The conversion clock for
the part is generated internally using a laser-trimmed clock
oscillator circuit. The BUSY signal indicates the end of
conversion and at this time the conversion results for both
channels are available to be read. The first read after a conversion accesses the result from VA1 or VB1, and the second read
accesses the result from VA2 or VB2, depending on whether the
multiplexer select A0 is low or high, respectively, before the
conversion is initiated. Data is read from the part via a 14-bit
parallel data bus with standard CS and RD signals.
Conversion time for the AD7863 is 5.2 μs in the high sampling
mode (10 μs for the auto sleep mode), and the track/hold
acquisition time is 0.5 μs. To obtain optimum performance
from the part, the read operation should not occur during the
conversion or during the 400 ns prior to the next conversion.
This allows the part to operate at throughput rates up to 175 kHz
and achieve data sheet specifications.
TRACK-AND-HOLD SECTION
The track-and-hold amplifiers on the AD7863 allow the ADCs
to accurately convert an input sine wave of full-scale amplitude
to 14-bit accuracy. The input bandwidth of the track-and-hold
is greater than the Nyquist rate of the ADC, even when the
ADC is operated at its maximum throughput rate of 175 kHz
(that is, the track-and hold can handle input frequencies in
excess of 87.5 kHz).
The track-and-hold amplifiers acquire input signals to 14-bit
accuracy in less than 500 ns. The operation of the track-andholds is essentially transparent to the user. The two track-and-hold
amplifiers sample their respective input channels simultaneously,
on the falling edge of CONVST. The aperture time for the
track-and-holds (that is, the delay time between the external
CONVST signal and the track-and-hold actually going into
hold) is well-matched across the two track-and-holds on one
device and also well-matched from device to device. This allows
the relative phase information between different input channels
to be accurately preserved. It also allows multiple AD7863s to
simultaneously sample more than two channels. At the end of
conversion, the part returns to its tracking mode. The acquisition
time of the track-and-hold amplifiers begins at this point.
REFERENCE SECTION
The AD7863 contains a single reference pin, labeled VREF, that
provides access to the part’s own 2.5 V reference. Alternatively,
an external 2.5 V reference can be connected to this pin, thus
providing the reference source for the part. The part is specified
with a 2.5 V reference voltage. Errors in the reference source
result in gain errors in the AD7863 transfer function and add to
the specified full-scale errors on the part. On the AD7863-10
and AD7863-3, it also results in an offset error injected in the
attenuator stage.
The AD7863 contains an on-chip 2.5 V reference. To use this
reference as the reference source for the AD7863, connect two
0.1 μF disc ceramic capacitors from the VREF pin to AGND. The
voltage that appears at this pin is internally buffered before
being applied to the ADC. If this reference is required for use
external to the AD7863, it should be buffered because the part
has a FET switch in series with the reference output resulting in
a source impedance for this output of 5.5 kΩ nominal. The
tolerance on the internal reference is ±10 mV at 25°C with a
typical temperature coefficient of 25 ppm/°C and a maximum
error over temperature of ±25 mV.
If the application requires a reference with a tighter tolerance or
the AD7863 needs to be used with a system reference, the user
has the option of connecting an external reference to this VREF
pin. The external reference effectively overdrives the internal
reference and thus provides the reference source for the ADC.
The reference input is buffered before being applied to the ADC
with a maximum input current of ±100 μA. A suitable reference
source for the AD7863 is the AD780 precision 2.5 V reference.
Rev. B | Page 9 of 24
AD7863
CIRCUIT DESCRIPTION
ANALOG INPUT SECTION
The AD7863 is offered as three part types: the AD7863-10,
which handles a ±10 V input voltage range, the AD7863-3,
which handles input voltage range ±2.5 V and the AD7863-2,
which handles a 0 V to 2.5 V input voltage range.
2.5V
REFERENCE
AD7863-10/AD7863-3
VREF
VAX
R1
TO ADC
REFERENCE
CIRCUITRY
R2
TO INTERNAL
COMPARATOR
MUX
R3
AGND
Table 6. Ideal Input/Output Code (AD7863-2)
TRACK/
HOLD
06411-005
2kΩ
Figure 5. AD7863-10/AD7863-3 Analog Input Structure
Analog Input1
+FSR − 1 LSB2
+FSR − 2 LSB
+FSR − 3 LSB
GND + 3 LSB
GND + 2 LSB
GND + 1 LSB
Digital Output Code Transition
111 . . . 110 to 111 . . . 111
111 . . . 101 to 111 . . . 110
111 . . . 100 to 111 . . . 101
000 . . . 010 to 000 . . . 011
000 . . . 001 to 000 . . . 010
000 . . . 000 to 000 . . . 001
1
FSR is full-scale range = 2.5 V for AD7863-2 with VREF = 2.5 V.
1 LSB = FSR/16,384 = 0.15 mV for AD7863-2 with VREF = 2.5 V.
2
Figure 5 shows the analog input section for the AD7863-10 and
AD7863-3. The analog input range of the AD7863-10 is ±10 V
into an input resistance of typically 9 kΩ. The analog input
range of the AD7863-3 is ±2.5 V into an input resistance of
typically 3 kΩ. This input is benign, with no dynamic charging
currents because the resistor stage is followed by a high input
impedance stage of the track-and-hold amplifier. For the
AD7863-10, R1 = 8 kΩ, R2 = 2 kΩ and R3 = 2 kΩ. For the
AD7863-3, R1 = R2 = 2 kΩ and R3 is open circuit.
For the AD7863-10 and AD7863-3, the designed code
transitions occur on successive integer LSB values (that is, 1 LSB,
2 LSBs, 3 LSBs . . .). Output coding is twos complement binary
with 1 LSB = FS/16,384. The ideal input/output transfer
function for the AD7863-10 and AD7863-3 is shown in Table 5.
Table 5. Ideal Input/Output Code (AD7863-10/AD7863-3)
Analog Input1
+FSR/2 − 1 LSB2
+FSR/2 − 2 LSBs
+FSR/2 − 3 LSBs
GND + 1 LSB
GND
GND − 1 LSB
−FSR/2 + 3 LSBs
−FSR/2 + 2 LSBs
−FSR/2 + 1 LSB
input current of less than 100 nA. This input is benign, with no
dynamic charging currents. Once again, the designed code
transitions occur on successive integer LSB values. Output
coding is straight (natural) binary with 1 LSB = FS/16,384 =
2.5 V/16,384 = 0.15 mV. Table 6 shows the ideal input/output
transfer function for the AD7863-2.
Digital Output Code Transition
011 . . . 110 to 011 . . . 111
011 . . . 101 to 011 . . . 110
011 . . . 100 to 011 . . . 101
000 . . . 000 to 000 . . . 001
111 . . . 111 to 000 . . . 000
111 . . . 110 to 111 . . . 111
100 . . . 010 to 100 . . . 011
100 . . . 001 to 100 . . . 010
100 . . . 000 to 100 . . . 001
OFFSET AND FULL-SCALE ADJUSTMENT
In most digital signal processing (DSP) applications, offset and
full-scale errors have little or no effect on system performance.
Offset error can always be eliminated in the analog domain by
ac coupling. Full-scale error effect is linear and does not cause
problems as long as the input signal is within the full dynamic
range of the ADC. Invariably, some applications require that the
input signal span the full analog input dynamic range. In such
applications, offset and full-scale error have to be adjusted to zero.
Figure 6 shows a typical circuit that can be used to adjust the
offset and full-scale errors on the AD7863 (VA1 on the
AD7863-10 version is shown for example purposes only).
Where adjustment is required, offset error must be adjusted
before full-scale error. This is achieved by trimming the offset
of the op amp driving the analog input of the AD7863 while the
input voltage is ½ LSB below analog ground. The trim
procedure is as follows: apply a voltage of −0.61 mV (−½ LSB)
at V1 in Figure 6 and adjust the op amp offset voltage until the
ADC output code flickers between 11 1111 1111 1111 and
00 0000 0000 0000.
INPUT RANGE = ±10V
V1
R1
10kΩ
R2
500Ω
VA1
1
The analog input section for the AD7863-2 contains no biasing
resistors and the VAX/BX pin drives the input directly to the
multiplexer and track-and-hold amplifier circuitry. The analog
input range is 0 V to 2.5 V into a high impedance stage with an
Rev. B | Page 10 of 24
R3
10kΩ
R4
10kΩ
AD7863*
R5
10kΩ
AGND
*ADDITIONAL PINS OMITTED FOR CLARITY.
Figure 6. Full-Scale Adjust Circuit
06411-006
FSR is full-scale range = 20 V (AD7863-10) and = 5 V (AD7863-3) with VREF = 2.5 V.
2
1 LSB = FSR/16,384 = 1.22 mV (AD7863-10) and 0.3 mV (AD7863-3) with
VREF = 2.5 V.
AD7863
signal indicates the end of conversion and at this time the
conversion results for both channels are available to be read. A
second conversion is then initiated. If the multiplexer select (A0)
is low, the first and second read pulses after the first conversion
accesses the result from Channel A (VA1 and VA2, respectively).
The third and fourth read pulses, after the second conversion
and A0 high, accesses the result from Channel B (VB1 and VB2,
respectively). The state of A0 can be changed any time after the
CONVST goes high, that is, track-and-holds into hold and 500 ns
prior to the next falling edge of CONVST. Note that A0 should
not be changed during conversion if the nonselected channels
have negative voltages applied to them, which are outside the
input range of the AD7863, because this affects the conversion
in progress. Data is read from the part via a 14-bit parallel data
bus with standard CS and RD signal, that is, the read operation
consists of a negative going pulse on the CS pin combined with
two negative going pulses on the RD pin (while the CS is low),
accessing the two 14-bit results. Once the read operation has
taken place, a further 400 ns should be allowed before the next
falling edge of CONVST to optimize the settling of the trackand-hold amplifier before the next conversion is initiated.
The achievable throughput rate for the part is 5.2 μs (conversion
time) plus 100 ns (read time) plus 0.4 μs (quiet time). This
results in a minimum throughput time of 5.7 μs (equivalent to
a throughput rate of 175 kHz).
Gain error can be adjusted at either the first code transition (ADC
negative full scale) or the last code transition (ADC positive full
scale). The trim procedures for both cases are as follows:
Positive Full-Scale Adjust (−10 Version)
Apply a voltage of 9.9927 V (FS/2 – 1 LSBs) at V1. Adjust R2
until the ADC output code flickers between 01 1111 1111 1110
and 01 1111 1111 1111.
Negative Full-Scale Adjust (−10 Version)
Apply a voltage of −9.9976 V (−FS + 1 LSB) at V1. Adjust R2
until the ADC output code flickers between 10 0000 0000 0000
and 10 0000 0000 0001.
An alternative scheme for adjusting full-scale error in systems
that use an external reference is to adjust the voltage at the VREF
pin until the full-scale error for any of the channels is adjusted
out. The good full-scale matching of the channels ensures small
full-scale errors on the other channels.
TIMING AND CONTROL
Figure 7 shows the timing and control sequence required to
obtain optimum performance (Mode 1) from the AD7863. In
the sequence shown, a conversion is initiated on the falling edge
of CONVST. This places both track-and-holds into hold
simultaneously and new data from this conversion is available
in the output register of the AD7863 5.2 μs later. The BUSY
tACQ
t8
CONVST
t3
BUSY
tCONV = 5.2µs
A0
CS
t1
t7
t2
t4
RD
t5
VA1
VA2
VB1
VB2
Figure 7. Mode 1 Timing Operation Diagram for High Sampling Performance
Rev. B | Page 11 of 24
06411-007
DATA
t6
AD7863
Read Options
CS
RD
DATA
CS
VA2
VA1
Figure 9. Read Option B (A0 is Low)
A0
VA1
VA2
06411-008
RD
CS
Figure 8. Read Option A (A0 is Low)
RD
DATA
VA1
VA2
Figure 10. Read Option C
Rev. B | Page 12 of 24
06411-010
DATA
VA1
06411-009
Apart from the read operation previously described and displayed
in Figure 7, other CS and RD combinations can result in different
channels/inputs being read in different combinations. Suitable
combinations are shown in Figure 8, Figure 9, and Figure 10.
AD7863
OPERATING MODES
MODE 1 OPERATION
Normal Power, High Sampling Performance
The timing diagram in Figure 7 is for optimum performance in
operating Mode 1 where the falling edge of CONVST starts
conversion and puts the track-and-hold amplifiers into their
hold mode. This falling edge of CONVST also causes the BUSY
signal to go high to indicate that a conversion is taking place.
The BUSY signal goes low when the conversion is complete,
which is 5.2 μs max after the falling edge of CONVST and new
data from this conversion is available in the output latch of the
AD7863. A read operation accesses this data. If the multiplexer
select A0 is low, the first and second read pulses after the first
conversion accesses the result from Channel A (VA1 and VA2,
respectively). The third and fourth read pulses, after the second
conversion and A0 high, access the result from Channel B (VB1
and VB2, respectively). Data is read from the part via a 14-bit
parallel data bus with standard CS and RD signals. This data
read operation consists of a negative going pulse on the CS pin
combined with two negative going pulses on the RD pin (while
the CS is low), accessing the two 14-bit results. For the fastest
throughput rate the read operation takes 100 ns. The read
operation must be complete at least 400 ns before the falling
edge of the next CONVST and this gives a total time of 5.7 μs
for the full throughput time (equivalent to 175 kHz). This mode
of operation should be used for high sampling applications.
MODE 2 OPERATION
Power-Down, Auto-Sleep After Conversion
The timing diagram in Figure 11 is for optimum performance
in operating Mode 2 where the part automatically goes into
sleep mode once BUSY goes low after conversion and wakes up
before the next conversion takes place. This is achieved by
keeping CONVST low at the end of the second conversion,
whereas it was high at the end of the second conversion for
Mode 1 operation.
The operation shown in Figure 11 shows how to access data
from both Channel A and Channel B, followed by the auto sleep
mode. One can also set up the timing to access data from
Channel A only or Channel B only (see the Read Options
section) and then go into auto sleep mode. The rising edge of
CONVST wakes up the part. This wake-up time is 4.8 μs when
using an external reference and 5 ms when using the internal
reference, at which point the track-and-hold amplifiers go into
their hold mode, provided the CONVST has gone low. The
conversion takes 5.2 μs after this giving a total of 10 μs (external
reference, 5.005 ms for internal reference) from the rising edge
of CONVST to the conversion being complete, which is
indicated by the BUSY going low.
Note that because the wake-up time from the rising edge of
CONVST is 4.8 μs, if the CONVST pulse width is greater than
5.2 μs the conversion takes more than the 10 μs (4.8 μs wake-up
time + 5.2 μs conversion time) shown in Figure 11 from the
rising edge of CONVST. This is because the track-and-hold
amplifiers go into their hold mode on the falling edge of
CONVST and the conversion does not complete for a further
5.2 μs. In this case, the BUSY is the best indicator of when the
conversion is complete. Even though the part is in sleep mode,
data can still be read from the part.
The read operation is identical to that in Mode 1 operation and
must also be complete at least 400 ns before the falling edge of
the next CONVST to allow the track-and-hold amplifiers to
have enough time to settle. This mode is very useful when the
part is converting at a slow rate because the power consumption
is significantly reduced from that of Mode 1 operation.
4.8µs*/5ms**
WAKE-UP TIME
tACQ
t8
CONVST
t3
t3
BUSY
tCONV = 5.2µs
tCONV = 5.2µs
A0
CS
RD
VA1
VB1
VA2
VB2
* WHEN USING AN EXTERNAL REFERENCE, WAKE-UP TIME = 4.8µs.
** WHEN USING AN INTERNAL REFERENCE, WAKE-UP TIME = 5ms.
Figure 11. Mode 2 Timing Diagram Where Automatic Sleep Function Is Initiated
Rev. B | Page 13 of 24
06411-011
DATA
AD7863
The AD7863 is specified and tested for dynamic performance as
well as traditional dc specifications such as integral and
differential nonlinearity. These ac specifications are required for
the signal processing applications such as phased array sonar,
adaptive filters, and spectrum analysis. These applications
require information on the ADC’s effect on the spectral content
of the input signal. Hence, the parameters for which the
AD7863 is specified include SNR, harmonic distortion,
intermodulation distortion, and peak harmonics. These terms
are discussed in more detail in the following sections.
frequency of 175 kHz. The SNR obtained from this graph is
−80.72 dB. It should be noted that the harmonics are taken into
account when calculating the SNR.
0
–10
–50
–60
–70
–80
–90
–100
–110
SNR is the measured signal-to-noise ratio at the output of the
ADC. The signal is the rms magnitude of the fundamental.
Noise is the rms sum of all the nonfundamental signals up to
half the sampling frequency (fS/2), excluding dc; SNR is
dependent upon the number of quantization levels used in the
digitization process; the more levels, the smaller the
quantization noise. The theoretical signal-to-noise ratio for a
sine wave input is given by
–130
(1)
where N is the number of bits.
–140
–150
4000
13.0
3000
12.5
06411-012
750
751
752
753
754
70
80
90
(2)
6.02
755
CODE
12.0
11.5
11.0
10.5
06411-014
749
60
Figure 14 shows a typical plot of effective numbers of bits vs.
frequency for an AD7863-2 with a sampling frequency of
175 kHz. The effective number of bits typically falls between
13.11 and 11.05 corresponding to SNR figures of 80.68 dB
and 68.28 dB.
13.5
748
50
The effective number of bits for a device can be calculated
directly from its measured SNR.
5000
747
40
SNR − 1.76
14.0
1000
30
The formula given in Equation 1 relates the SNR to the number
of bits. Rewriting the formula, as in Equation 2, it is possible to
obtain a measure of performance expressed in effective number
of bits (N).
6000
2000
20
EFFECTIVE NUMBER OF BITS
ENOB
COUNTS
7000
10
Figure 13. AD7863 FFT Plot
N=
8000
0
FREQUENCY (kHz)
Thus for an ideal 14-bit converter, SNR = 86.04 dB.
Figure 12 shows a histogram plot for 8192 conversions of a dc
input using the AD7863 with 5 V supply. The analog input was
set at the center of a code transition. It can be seen that the
codes appear mainly in the one output bin, indicating very good
noise performance from the ADC.
06411-013
–120
SNR = (6.02N + 1.76) dB
746
SNR = +80.72dB
THD = –92.96dB
–40
SIGNAL-TO-NOISE RATIO (SNR)
0
fSAMPLE = 175kHz
fIN = 10kHz
–20
–30
(dB)
AD7863 DYNAMIC SPECIFICATIONS
Figure 12. Histogram of 8192 Conversions of a DC Input
10.0
The output spectrum from the ADC is evaluated by applying
a sine wave signal of very low distortion to the VAX/BX input,
which is sampled at a 175 kHz sampling rate. A fast fourier
transform (FFT) plot is generated from which the SNR data can
be obtained. Figure 13 shows a typical 8192 point FFT plot of
the AD7863 with an input signal of 10 kHz and a sampling
Rev. B | Page 14 of 24
0
200
400
600
800
FREQUENCY (kHz)
Figure 14. Effective Numbers of Bits vs. Frequency
1000
AD7863
TOTAL HARMONIC DISTORTION (THD)
PEAK HARMONIC OR SPURIOUS NOISE
Total harmonic distortion (THD) is the ratio of the rms sum of
harmonics to the rms value of the fundamental. For the
AD7863, THD is defined as
Harmonic or spurious noise is defined as the ratio of the rms
value of the next largest component in the ADC output
spectrum (up to fS/2 and excluding dc) to the rms value of the
fundamental. Normally, the value of this specification is
determined by the largest harmonic in the spectrum, but for
parts where the harmonics are buried in the noise floor, the
peak is a noise peak.
V2 + V3 + V4 + V5
2
2
2
2
(3)
V1
where:
DC LINEARITY PLOT
V1 is the rms amplitude of the fundamental.
V2, V3, V4, and V5 are the rms amplitudes of the second through
the fifth harmonic.
Figure 16 and Figure 17 show typical DNL and INL plots for
the AD7863.
1.0
THD is also derived from the FFT plot of the ADC output
spectrum.
In this case, the second and third order terms are of different
significance. The second order terms are usually distanced in
frequency from the original sine waves while the third order
terms are usually at a frequency close to the input frequencies.
As a result, the second and third order terms are specified
separately. The calculation of the intermodulation distortion is
as per the THD specification where it is the ratio of the rms
sum of the individual distortion products to the rms amplitude
of the fundamental expressed in dBs. In this case, the input
consists of two equal amplitude, low distortion sine waves.
Figure 15 shows a typical IMD plot for the AD7863.
0
2048
4096
6144
8192
10240
12288
14336
16383
12288
14336
16383
ADC CODE
Figure 16. DC DNL Plot
1.0
0.5
0
–40
–1.0
IMD
2ND ORDER TERM
–98.21dB
3RD ORDER TERM
–93.91dB
–50
–60
–70
–90
–110
–120
06411-015
10
20
30
40
50
60
70
80
2048
4096
6144
8192
10240
Figure 17. DC INL Plot
–100
0
0
ADC CODE
–80
–130
06411-017
INPUT FREQUENCIES
F1 = 50.13kHz
F2 = 49.13kHz
fSAMPLE = 175kHz
–20
–30
(dB)
–1.0
–0.5
0
–10
–140
–150
0
–0.5
INL ERROR (LSB)
With inputs consisting of sine waves at two frequencies, fa and
fb, any active device with nonlinearities creates distortion
products at sum and difference frequencies of mfa ± nfb where
m, n = 0, 1, 2, 3 . . . Intermodulation terms are those for which
neither m nor n is equal to zero. For example, the second order
terms include (fa + fb) and (fa − fb) and the third order terms
include (2fa + fb), (2fa − fb), (fa + 2fb), and (fa − 2fb).
DNL ERROR (LSB)
0.5
INTERMODULATION DISTORTION
06411-016
THD (dB ) = 20 log
90
FREQUENCY (kHz)
Figure 15. IMD Plot
Rev. B | Page 15 of 24
AD7863
POWER CONSIDERATIONS
In the automatic power-down mode the part can be operated at
a sample rate that is considerably less than 175 kHz. In this case,
the power consumption is reduced and depends on the sample
rate. Figure 18 shows a graph of the power consumption vs.
sampling rates from 1 Hz to 100 kHz in the automatic powerdown mode. The conditions are 5 V supply at 25°C.
50
45
40
30
25
20
15
10
06411-018
POWER (mW)
35
5
0
0
10
20
30
40
50
60
70
FREQUENCY (kHz)
80
90
100
Figure 18. Power vs. Sample Rate in Auto Power-Down
Rev. B | Page 16 of 24
AD7863
MICROPROCESSOR INTERFACING
The AD7863 high speed bus timing allows direct interfacing to
DSP processors as well as modern 16-bit microprocessors.
Suitable microprocessor interfaces are shown in Figure 19
through Figure 23.
AD7863 TO ADSP-2100 INTERFACE
Figure 19 shows an interface between the AD7863 and the
ADSP-2100. The CONVST signal can be supplied from the
ADSP-2100 or from an external source. The AD7863 BUSY line
provides an interrupt to the ADSP-2100 when conversion is
completed on both channels. The two conversion results can
then be read from the AD7863 using two successive reads to the
same memory address. The following instruction reads one of
the two results:
AD7863 TO TMS32010 INTERFACE
An interface between the AD7863 and the TMS32010 is shown
in Figure 20. Once again the CONVST signal can be supplied
from the TMS32010 or from an external source, and the
TMS32010 is interrupted when both conversions have been
completed. The following instruction is used to read the
conversion results from the AD7863:
IN D, ADC
where:
D is data memory address.
ADC is the AD7863 address.
PA0
where:
TMS32010
MEN
MR0 is the ADSP-2100 MR0 register.
ADC is the AD7863 address.
EN
AD7863*
DB13
DB0
CS CONVST
A0
D15
D0
AD7863*
BUSY
DMRD (RD)
A0
RD
ADDRESS BUS
ADDR
DECODE
CS CONVST
BUSY
DEN
OPTIONAL
IRQn
DATA BUS
*ADDITIONAL PINS OMITTED FOR CLARITY.
Figure 20. AD7863 to TMS32010 Interface
RD
AD7863 TO TMS320C25 INTERFACE
DB13
DB0
06411-019
DMD15
DMD0
ADDRESS
DECODE
EN
06411-020
ADSP-2100
(ADSP-2101/
ADSP-2102) DMS
ADDRESS BUS
INT
DMA13
DMA0
OPTIONAL
PA2
MR0 = DM (ADC)
DATA BUS
*ADDITIONAL PINS OMITTED FOR CLARITY.
Figure 19. AD7863 to ADSP-2100 Interface
AD7863 TO ADSP-2101/ADSP-2102 INTERFACE
The interface outlined in Figure 19 also forms the basis for an
interface between the AD7863 and the ADSP-2101/ADSP-2102.
The READ line of the ADSP-2101/ADSP-2102 is labeled RD. In
this interface, the RD pulse width of the processor can be
programmed using the data memory wait state control register.
The instruction used to read one of the two results is as outlined
for the ADSP-2100.
Figure 21 shows an interface between the AD7863 and the
TMS320C25. As with the two previous interfaces, conversion
can be initiated from the TMS320C25 or from an external
source, and the processor is interrupted when the conversion
sequence is completed. The TMS320C25 does not have a
separate RD output to drive the AD7863 RD input directly. This
has to be generated from the processor STRB and R/W outputs
with the addition of some logic gates. The RD signal is OR
gated with the MSC signal to provide the one WAIT state
required in the read cycle for correct interface timing.
Conversion results are read from the AD7863 using the
following instruction:
IN D, ADC
where:
D is data memory address.
ADC is the AD7863 address.
Rev. B | Page 17 of 24
AD7863
OPTIONAL
A15
A0
INTn
CS CONVST
A0
MC68000
AD7863*
BUSY
STRB
ADDRESS
DECODE
EN
CONVST
CS
DTACK
AD7863*
RD
AS
R/W
R/W
RD
READY
DB13
MSC
DB0
D15
DB0
D0
DATA BUS
*ADDITIONAL PINS OMITTED FOR CLARITY.
06411-021
DB13
DMD15
DMD0
A0
Figure 22. AD7863 to MC68000 Interface
AD7863 TO 80C196 INTERFACE
Figure 21. AD7863 to TMS320C25 Interface
Some applications may require that the conversion be initiated
by the microprocessor rather than an external timer. One
option is to decode the AD7863 CONVST from the address bus
so that a write operation starts a conversion. Data is read at the
end of the conversion sequence as before. Figure 23 shows an
example of initiating conversion using this method. Note that
for all interfaces, it is preferred that a read operation not be
attempted during conversion.
Figure 23 shows an interface between the AD7863 and the
80C196 microprocessor. Here, the microprocessor initiates
conversion. This is achieved by gating the 80C196 WR signal
with a decoded address output (different from the AD7863 CS
address). The AD7863 BUSY line is used to interrupt the
microprocessor when the conversion sequence is completed.
A15
A1
AD7863 TO MC68000 INTERFACE
80C196
An interface between the AD7863 and the MC68000 is shown
in Figure 22. As before, conversion can be supplied from the
MC68000 or from an external source. The AD7863 BUSY line
can be used to interrupt the processor or, alternatively, software
delays can ensure that conversion has been completed before a
read to the AD7863 is attempted. Because of the nature of its
interrupts, the MC68000 requires additional logic (not shown
in Figure 23) to allow it to be interrupted correctly. For further
information on MC68000 interrupts, consult the MC68000
users manual.
The MC68000 AS and R/W outputs are used to generate a
separate RD input signal for the AD7863. CS is used to drive
the MC68000 DTACK input to allow the processor to execute
a normal read operation to the AD7863. The conversion results
are read using the following MC68000 instruction:
MOVE.W ADC, D0
where:
D0 is the 68000 D0 register.
ADC is the AD7863 address.
DATA BUS
*ADDITIONAL PINS OMITTED FOR CLARITY.
06411-022
IS
A0
ADDRESS
DECODE
EN
ADDRESS BUS
ADDRESS BUS
ADDRESS
DECODE
EN
CS
A0
AD7863*
BUSY
WR
RD
RD
DB13
DB0
D15
D0
DATA BUS
*ADDITIONAL PINS OMITTED FOR CLARITY.
06411-023
TMS320C25
OPTIONAL
A15
ADDRESS BUS
Figure 23. AD7863–80C196 Interface
VECTOR MOTOR CONTROL
The current drawn by a motor can be split into two components:
one produces torque and the other produces magnetic flux.
For optimal performance of the motor, these two components
should be controlled independently. In conventional methods of
controlling a three-phase motor, the current (or voltage)
supplied to the motor and the frequency of the drive are the
basic control variables. However, both the torque and flux are
functions of current (or voltage) and frequency. This coupling
effect can reduce the performance of the motor because, for
example, if the torque is increased by increasing the frequency,
the flux tends to decrease.
Rev. B | Page 18 of 24
AD7863
MULTIPLE AD7863S
A block diagram of a vector motor control application using the
AD7863 is shown in Figure 24. The position of the field is
derived by determining the current in each phase of the motor.
Only two phase currents need to be measured because the third
can be calculated if two phases are known. VA1 and VA2 of the
AD7863 are used to digitize this information.
Figure 25 shows a system where a number of AD7863s can be
configured to handle multiple input channels. This type of
configuration is common in applications such as sonar and
radar. The AD7863 is specified with typical limits on aperture
delay. This means that the user knows the difference in the
sampling instant between all channels. This allows the user to
maintain relative phase information between the different
channels.
VA1
VB1
VA2
IC
DAC
DAC
DAC
IB
DRIVE
CIRCUITRY
IA
TORQUE
SETPOINT
VB
VA1
VA
VA1
VA2
AD7863
(2)
VB2
CS
VREF
VA1
VB1
VA2
VB2
VA2
AD7863*
VB1
VB2
VOLTAGE
ATTENUATORS
06411-024
*ADDITIONAL PINS
OMITTED FOR CLARITY.
RD
VB1
VREF
ADDRESS
DECODE
ADDRESS
RD
AD7863
(n)
CS
A common read signal from the microprocessor drives the RD
input of all AD7863s. Each AD7863 is designated a unique
address selected by the address decoder. The reference output of
AD7863 Number 1 is used to drive the reference input of all
other AD7863s in the circuit shown in Figure 25. One VREF can
be used to provide the reference to several other AD7863s.
Alternatively, an external or system reference can be used to
drive all VREF inputs. A common reference ensures good fullscale tracking between all channels.
THREE
PHASE
MOTOR
ISOLATION
AMPLIFIERS
TRANSFORMATION
TO TORQUE AND
FLUX CURRENT
COMPONENTS
CS
VREF
Figure 25. Multiple AD7863s in Multichannel System
DSP
MICROPROCESSOR
FLUX
SETPOINT
RD
(1)
VB2
Simultaneous sampling is critical to maintaining the relative
phase information between the two channels. A current sensing
isolation amplifier, transformer, or Hall effect sensor is used
between the motor and the AD7863. Rotor information is
obtained by measuring the voltage from two of the inputs to the
motor. VB1 and VB2 of the AD7863 are used to obtain this
information. Once again the relative phase of the two channels
is important. A DSP microprocessor is used to perform the
mathematical transformations and control loop calculations on
the information fed back by the AD7863.
TORQUE AND FLUX
CONTROL LOOP
CALCULATIONS AND
TWO TO THREE
PHASE
INFORMATION
RD
AD7863
06411-025
Vector control of an ac motor involves controlling the phase in
addition to drive and current frequency. Controlling the phase
of the motor requires feedback information on the position of
the rotor relative to the rotating magnetic field in the motor.
Using this information, a vector controller mathematically
transforms the three phase drive currents into separate torque
and flux components. The AD7863 is ideally suited for use in
vector motor control applications.
Figure 24. Vector Motor Control Using the AD7863
Rev. B | Page 19 of 24
AD7863
APPLICATIONS HINTS
Fair-Rite 274300111 or Murata BL01/02/03) should be located
within three inches of the AD7863.
PC BOARD LAYOUT CONSIDERATIONS
The AD7863 is optimally designed for lowest noise performance,
both radiated and conducted noise. To complement the
excellent noise performance of the AD7863 it is imperative that
great care be given to the PC board layout. Figure 26 shows a
recommended connection diagram for the AD7863.
The PCB power plane (VCC) should provide power to all digital
logic on the PC board, and the analog power plane (VDD) should
provide power to all AD7863 power pins, voltage reference
circuitry and any input amplifiers, if needed. A suitable low
noise amplifier for the AD7863 is the AD797, one for each
input. Ensure that the +VS and the −VS supplies to each
amplifier are individually decoupled to AGND.
GROUND PLANES
The AD7863 and associated analog circuitry should have a
separate ground plane, referred to as the analog ground plane
(AGND). This analog ground plane should encompass all
AD7863 ground pins (including the DGND pin), voltage
reference circuitry, power supply bypass circuitry, the analog
input traces, and any associated input/buffer amplifiers.
The PCB power (VCC) and ground (DGND) should not overlay
portions of the analog power plane (VDD). Keeping the VCC
power and the DGND planes from overlaying the VDD contributes
to a reduction in plane-to-plane noise coupling.
SUPPLY DECOUPLING
The regular PCB ground plane (referred to as the DGND for
this discussion) area should encompass all digital signal traces,
excluding the ground pins, leading up to the AD7863.
Noise on the analog power plane (VDD) can be further reduced
by use of multiple decoupling capacitors (Figure 26).
POWER PLANES
Optimum performance is achieved by the use of disc ceramic
capacitors. The VDD and reference pins (whether using an
external or an internal reference) should be individually
decoupled to the analog ground plane (AGND). This should be
done by placing the capacitors as close as possible to the
AD7863 pins with the capacitor leads as short as possible, thus
minimizing lead inductance.
The PC board layout should have two distinct power planes,
one for analog circuitry and one for digital circuitry. The analog
power plane should encompass the AD7863 (VDD) and all
associated analog circuitry. This power plane should be
connected to the regular PCB power plane (VCC) at a single
point, if necessary through a ferrite bead, as illustrated in
Figure 26. This bead (part numbers for reference:
L
(FERRITE BEAD)
VIN
TEMP
0.1µF
0.1µF
10µF
47µF
ANALOG
SUPPLY
+5V
AD780
VOUT
VDD
VREF
+15V
0.1µF
0.1µF
0.1µF
AGND
DGND
+VS
AGND
VA1
VA1
AD7863
VB1
VB1
VA2
VA2
VB2
VB2
4 × AD797s
0.1µF
ANALOG
SUPPLY
–15V
06411-026
–VS
Figure 26. Typical Connections Diagram Including the Relevant Decoupling
Rev. B | Page 20 of 24
AD7863
OUTLINE DIMENSIONS
18.10 (0.7126)
17.70 (0.6969)
15
28
7.60 (0.2992)
7.40 (0.2913)
1
10.65 (0.4193)
10.00 (0.3937)
14
0.75 (0.0295)
0.25 (0.0098)
2.65 (0.1043)
2.35 (0.0925)
0.30 (0.0118)
0.10 (0.0039)
COPLANARITY
0.10
1.27 (0.0500)
BSC
0.51 (0.0201)
0.31 (0.0122)
SEATING
PLANE
45°
8°
0°
0.33 (0.0130)
0.20 (0.0079)
1.27 (0.0500)
0.40 (0.0157)
060706-A
COMPLIANT TO JEDEC STANDARDS MS-013-AE
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 27. 28-Lead Standard Small Outline Package [SOIC_W]
Wide Body
(RW-28)
Dimensions shown in millimeters and (inches)
10.50
10.20
9.90
15
28
5.60
5.30
5.00
1
8.20
7.80
7.40
14
0.65 BSC
0.38
0.22
SEATING
PLANE
8°
4°
0°
COMPLIANT TO JEDEC STANDARDS MO-150-AH
Figure 28. 28-Lead Shrink Small Outline Package [SSOP]
(RS-28)
Dimensions shown in millimeters
Rev. B | Page 21 of 24
0.95
0.75
0.55
060106-A
0.05 MIN
COPLANARITY
0.10
0.25
0.09
1.85
1.75
1.65
2.00 MAX
AD7863
ORDERING GUIDE
Model
AD7863AR-10
AD7863AR-10REEL
AD7863AR-10REEL7
AD7863ARZ-101
AD7863ARZ-10REEL1
AD7863ARZ-10REEL71
AD7863ARS-10
AD7863ARS-10REEL
AD7863ARS-10REEL7
AD7863ARSZ-101
AD7863ARSZ-10REEL1
AD7863ARSZ-10REEL71
AD7863BR-10
AD7863BR-10REEL
AD7863BR-10REEL7
AD7863BRZ-10 1
AD7863AR-3
AD7863AR-3REEL
AD7863AR-3REEL7
AD7863ARZ-31
AD7863ARS-3
AD7863ARS-3REEL
AD7863ARS-3REEL7
AD7863ARSZ-31
AD7863ARSZ-3REEL1
AD7863ARSZ-3REEL71
AD7863BR-3
AD7863BR-3REEL
AD7863BR-3REEL7
AD7863BRZ-31
AD7863AR-2
AD7863AR-2REEL
AD7863AR-2REEL7
AD7863ARZ-21
AD7863ARZ-2REEL1
AD7863ARZ-2REEL71
AD7863ARS-2
AD7863ARS-2REEL
AD7863ARS-2REEL7
AD7863ARSZ-21
AD7863ARSZ-2REEL1
AD7863ARSZ-2REEL71
EVAL-AD7863CB
1
Input Range
±10 V
±10 V
±10 V
±10 V
±10 V
±10 V
±10 V
±10 V
±10 V
±10 V
±10 V
±10 V
±10 V
±10 V
±10 V
±10 V
±2.5 V
±2.5 V
±2.5 V
±2.5 V
±2.5 V
±2.5 V
±2.5 V
±2.5 V
±2.5 V
±2.5 V
±2.5 V
±2.5 V
±2.5 V
±2.5 V
0 V to 2.5 V
0 V to 2.5 V
0 V to 2.5 V
0 V to 2.5 V
0 V to 2.5 V
0 V to 2.5 V
0 V to 2.5 V
0 V to 2.5 V
0 V to 2.5 V
0 V to 2.5 V
0 V to 2.5 V
0 V to 2.5 V
Relative Accuracy
±2.5 LSB
±2.5 LSB
±2.5 LSB
±2.5 LSB
±2.5 LSB
±2.5 LSB
±2.5 LSB
±2.5 LSB
±2.5 LSB
±2.5 LSB
±2.5 LSB
±2.5 LSB
±2.0 LSB
±2.0 LSB
±2.0 LSB
±2.0 LSB
±2.5 LSB
±2.5 LSB
±2.5 LSB
±2.5 LSB
±2.5 LSB
±2.5 LSB
±2.5 LSB
±2.5 LSB
±2.5 LSB
±2.5 LSB
±2.0 LSB
±2.0 LSB
±2.0 LSB
±2.0 LSB
±2.5 LSB
±2.5 LSB
±2.5 LSB
±2.5 LSB
±2.5 LSB
±2.5 LSB
±2.5 LSB
±2.5 LSB
±2.5 LSB
±2.5 LSB
±2.5 LSB
±2.5 LSB
Temperature Range
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
Z = Pb-free part.
Rev. B | Page 22 of 24
Package Description
28-Lead SOIC_W
28-Lead SOIC_W
28-Lead SOIC_W
28-Lead SOIC_W
28-Lead SOIC_W
28-Lead SOIC_W
28-Lead SSOP
28-Lead SSOP
28-Lead SSOP
28-Lead SSOP
28-Lead SSOP
28-Lead SSOP
28-Lead SOIC_W
28-Lead SOIC_W
28-Lead SOIC_W
28-Lead SOIC_W
28-Lead SOIC_W
28-Lead SOIC_W
28-Lead SOIC_W
28-Lead SOIC_W
28-Lead SSOP
28-Lead SSOP
28-Lead SSOP
28-Lead SSOP
28-Lead SSOP
28-Lead SSOP
28-Lead SOIC_W
28-Lead SOIC_W
28-Lead SOIC_W
28-Lead SOIC_W
28-Lead SOIC_W
28-Lead SOIC_W
28-Lead SOIC_W
28-Lead SOIC_W
28-Lead SOIC_W
28-Lead SOIC_W
28-Lead SSOP
28-Lead SSOP
28-Lead SSOP
28-Lead SSOP
28-Lead SSOP
28-Lead SSOP
Evaluation Board
Package Option
RW-28
RW-28
RW-28
RW-28
RW-28
RW-28
RS-28
RS-28
RS-28
RS-28
RS-28
RS-28
RW-28
RW-28
RW-28
RW-28
RW-28
RW-28
RW-28
RW-28
RS-28
RS-28
RS-28
RS-28
RS-28
RS-28
RW-28
RW-28
RW-28
RW-28
RW-28
RW-28
RW-28
RW-28
RW-28
RW-28
RS-28
RS-28
RS-28
RS-28
RS-28
RS-28
AD7863
NOTES
Rev. B | Page 23 of 24
AD7863
NOTES
©2006 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D06411-0-11/06(B)
Rev. B | Page 24 of 24
Similar pages