ON ENA2016 Bidirectional motor driver Datasheet

Ordering number : ENA2016
LB1846MC
Monolithic Digital IC
Low-Voltage/Low Saturation Voltage Type
Bidirectional Motor Driver
http://onsemi.com
Overview
The LB1846MC is 2-channel low-voltage, low saturation voltage type bidirectional motor driver IC that is optimal for
use as 2-phase stepping motor drivers in printers, cameras and other portable equipment. The output circuits are of the
bipolar type, with PNP transistors in the upper side and NPN transistors in the lower side, and they achieve low
saturation output and low power characteristics despite being provided in a miniature package.
The LB1846MC products can directly control a motor from signals from a microcontroller. The LB1846MC is optimal
for 1-2 phase excitation drive for 2-phase stepping motors using 4-input logic (IN1, IN2, IN3 and IN4).
Another point is that these IC include built-in thermal shutdown circuits so that IC scorching or burning is prevented in
advance even if the IC output is shorted.
Functions
• Optimal for 1-2 phase excitation drive for 2-phase stepping motors
• Standby current: Zero
• Low saturation voltage. VO (sat) = 0.55V typical at IO = 400mA
• Thermal shutdown circuit
• No limitations on the magnitude relationship between the power supply voltage (VCC) and the input voltage (VIN)
Specifications
Absolute Maximum Ratings at Ta = 25°C
Parameter
Maximum supply voltage
Symbol
Conditions
Ratings
Unit
VCC max
-0.3 to +8.0
V
Output voltage
VOUT
VCC + VSF
V
Input voltage
VIN
-0.3 to +8.0
Ground pin outflow current
IGND
Per channel
Allowable power dissipation
Pd max
When mounted*
Operating temperature
Topr
-20 to +75
°C
Storage temperature
Tstg
-40 to +150
°C
V
800
mA
870
mW
*1: When mounted on the specified printed circuit board (114.3mm × 76.2mm × 1.5mm), glass epoxy board
Caution 1) Absolute maximum ratings represent the value which cannot be exceeded for any length of time.
Caution 2) Even when the device is used within the range of absolute maximum ratings, as a result of continuous usage under high temperature, high current,
high voltage, or drastic temperature change, the reliability of the IC may be degraded. Please contact us for the further details.
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating
Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability.
Semiconductor Components Industries, LLC, 2013
June, 2013
30712 SY 20120112-S00002 No.A2016-1/4
LB1846MC
Allowable Operating Ranges at Ta = 25°C
Parameter
Symbol
Conditions
Ratings
Unit
Supply voltage
VCC
2.5 to 7.5
Input high-level voltage
VIH
2.5 to 7.5
V
V
Input low-level voltage
VIL
-0.3 to +0.7
V
Electrical Characteristics at Ta = 25°C, VCC = 5V
Parameter
Symbol
Current drain
Output saturation voltage
Input current
Ratings
Conditions
min
typ
Unit
max
ICC0
IN1, 2, 3, 4 = 0V
0.1
10
µA
ICC1
IN1, 3 = 3V, IN2, 4 = 0V
30
40
mA
VOUT1
VIN = 3V or 0V, VCC = 3 to 7.5V, IOUT = 200mA
0.27
0.4
V
VOUT2
VIN = 3V or 0V, VCC = 4 to 7.5V, IOUT = 400mA
0.55
0.8
V
IIN
VIN = 5V
150
200
µA
30
µA
1.7
V
Spark Killer Diode
Reverse current
IS (leak)
Forward voltage
VSF
IOUT = 400mA
Package Dimensions
unit : mm (typ)
3420
5.0
Allowable power dissipation, Pdmax - mW
0.5
4.4
6.2
10
1
2
1.0
0.15
0.35
0.05 (1.5)
1.55
0.8 MAX
Pd max -- Ta
1000
870
800
600
522
400
200
0
--20
0
SANYO : MFP10SK(225mil)
20
40
60
80
100
Ambient temperature, Ta - C
Pin Assignment
VCC
1
10 OUT4
IN4
2
9
OUT3
IN3
3
8
OUT1
IN1
4
7
OUT2
IN2
5
6
GND
LB1846MC
Top view
No.A2016-2/4
LB1846MC
Block Diagram
VCC
IN1
OUT1
Stepping
Motor
OUT2
IN3
Thermal shutdown circuit
Control block
IN2
IN4
OUT3
OUT4
GND
Truth Tables
IN1
IN2
IN3
IN4
OUT1
OUT2
OUT3
OUT4
Note
L
L
L
L
OFF
OFF
OFF
OFF
Standby
H
L
L
L
H
L
OFF
OFF
L
H
L
H
L
H
L
H
L
L
H
L
OFF
OFF
H
L
L
H
H
L
L
H
H
L
L
H
L
L
L
H
OFF
OFF
L
H
L
H
L
H
L
H
L
L
L
H
OFF
OFF
L
H
H
L
L
H
H
L
L
H
H
H
-
-
-
-
H
H
1-2 phase excitation
The logic output for the first high-level input is
produced. *2
Note: *1 "-" indicates a "don‛t care" input.
*2 If two high levels (H/H) are input to the IN1/IN2 pins with the timing shown in (1) in the figure below, then the IN2 input that arrived later will be
ignored and the IC will function as though an H/L combination is applied to the IN1/IN2 pins. Similarly, the timing shown in (2) results in a L/H
combination on the IN1/IN2 pins.
(1)
(2)
IN1(IN3)
L
H
H
IN1(IN3)
L
L
H
IN2(IN4)
L
L
H
IN2(IN4)
L
H
H
No.A2016-3/4
LB1846MC
ICC - VCC Characterstics
50
IIN -- VIN
280
VCC=5V
VCC=VIN, IN1 / 2 / 3 / 4=H / L / H / L
240
Input current, IIN - μA
Current drain, ICC - mA
40
30
20
200
160
120
80
10
40
0
0
0
1
2
3
4
5
6
7
8
9
Power-supply voltage, VCC - V
1
2
3
4
5
6
7
8
9
Input voltage, VIN - V
VOUT -- IOUT
1.0
Output saturation voltage, VOUT - V
0
VCC=VIN=4.0V
0.8
0.6
0.4
0.2
0
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
Input current, IOUT - A
ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number
of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at
www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no
warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the
application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental
damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual
performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical
experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use
as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in
which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for
any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors
harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or
death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the
part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PS No.A2016-4/4
Similar pages