TI1 LP3853ES-5.0/NOPB Lp3853/lp3856 3a fast response ultra low dropout linear regulator Datasheet

LP3853, LP3856
www.ti.com
SNVS173G – FEBRUARY 2003 – REVISED APRIL 2013
LP3853/LP3856 3A Fast Response Ultra Low Dropout Linear Regulators
Check for Samples: LP3853, LP3856
FEATURES
DESCRIPTION
•
•
•
•
•
•
•
•
•
•
•
•
The LP3853/LP3856 series of fast ultra low-dropout
linear regulators operate from a +2.5V to +7.0V input
supply. Wide range of preset output voltage options
are available. These ultra low dropout linear
regulators respond very quickly to step changes in
load, which makes them suitable for low voltage
microprocessor applications. The LP3853/LP3856 are
developed on a CMOS process which allows low
quiescent current operation independent of output
load current. This CMOS process also allows the
LP3853/LP3856 to operate under extremely low
dropout conditions.
1
2
Ultra Low Dropout Voltage
Stable with Selected Ceramic Capacitors
Low Ground Pin Current
Load Regulation of 0.08%
10nA Quiescent Current in Shutdown Mode
Ensured Output Current of 3A DC
Available in TO-263 and TO-220 Packages
Output Voltage Accuracy ± 1.5%
Error Flag Indicates Output Status
Sense Option Improves Load Regulation
Overtemperature/overcurrent Protection
−40°C to +125°C Junction Temperature Range
Ground Pin Current: Typically 4mA at 3A load
current.
APPLICATIONS
•
•
•
•
•
•
•
•
•
Dropout Voltage: Ultra low dropout voltage; typically
39mV at 300mA load current and 390mV at 3A load
current.
Microprocessor Power Supplies
Stable with Ceramic Output Capacitors
GTL, GTL+, BTL, and SSTL Bus Terminators
Power Supplies for DSPs
SCSI Terminator
Post Regulators
High Efficiency Linear Regulators
Battery Chargers
Other Battery Powered Applications
Shutdown Mode: Typically 10nA quiescent current
when the shutdown pin is pulled low.
Error Flag:Error flag goes low when the output
voltage drops 10% below nominal value.
SENSE: Sense pin improves regulation at remote
loads.
Precision Output Voltage: Multiple output voltage
options are available ranging from 1.8V to 5.0V with a
ensured accuracy of ±1.5% at room temperature, and
±3.0% over all conditions (varying line, load, and
temperature).
Typical Application Circuits
INPUT
3.3V ± 10%
VIN
CIN*
10 PF
VOUT
COUT*
LP3853-1.8
SD**
SD
ERROR
GND
ERROR**
VOUT
1.8V, 3.0A
10 PF
* TANTALUM OR
CERAMIC
**SD and ERROR pins must be pulled high through a 10kΩ pull-up resistor. Connect the ERROR pin to ground if this
function is not used. See Application Hints for more information.
INPUT
3.3V ± 10%
VIN
CIN*
10 PF
VOUT
LP3856-1.8
SD**
SD
SENSE
GND
COUT*
VOUT
1.8V, 3.0A
10 PF
* TANTALUM OR
CERAMIC
**SD pin must be pulled high through a 10kΩ pull-up resistor. See Application Hints for more information.
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2003–2013, Texas Instruments Incorporated
LP3853, LP3856
SNVS173G – FEBRUARY 2003 – REVISED APRIL 2013
www.ti.com
Connection Diagram
Figure 1. Top View
TO220-5 Package
Bent, Staggered Leads
Figure 2. Top View
TO263-5 Package
Table 1. Pin Description for TO220-5 and TO263-5 Packages
Pin #
LP3853
Name
LP3856
Function
Name
Function
1
SD
Shutdown
SD
Shutdown
2
VIN
Input Supply
VIN
Input Supply
3
GND
Ground
GND
Ground
4
VOUT
Output Voltage
VOUT
Output Voltage
5
ERROR
ERROR Flag
SENSE
Remote Sense Pin
Block Diagram
LP3853
Figure 3.
2
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LP3853 LP3856
LP3853, LP3856
www.ti.com
SNVS173G – FEBRUARY 2003 – REVISED APRIL 2013
LP3856
Figure 4.
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings
(1)
−65°C to +150°C
Storage Temperature Range
Lead Temperature
(Soldering, 5 sec.)
ESD Rating
260°C
(2)
Power Dissipation
2 kV
(3)
Internally Limited
−0.3V to +7.5V
Input Supply Voltage (Survival)
−0.3V to 7.5V
Shutdown Input Voltage (Survival)
Output Voltage (Survival),
(4) (5)
−0.3V to +6.0V
,
IOUT (Survival)
Short Circuit Protected
Maximum Voltage for ERROR Pin
VIN
Maximum Voltage for SENSE Pin
VOUT
(1)
(2)
(3)
(4)
(5)
Absolute maximum ratings indicate limits beyond which damage to the device may occur. Operating ratings indicate conditions for which
the device is intended to be functional, but does not ensure specific performance limits. For ensured specifications and test conditions,
see Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may
degrade when the device is not operated under the listed test conditions.
The human body model is a 100pF capacitor discharged through a 1.5kΩ resistor into each pin.
At elevated temperatures, devices must be derated based on package thermal resistance. The devices in TO220 package must be
derated at θjA = 50°C/W (with 0.5in2, 1oz. copper area), junction-to-ambient (with no heat sink). The devices in the TO263 surfacemount package must be derated at θjA = 60°C/W (with 0.5in2, 1oz. copper area), junction-to-ambient. See Application Hints.
If used in a dual-supply system where the regulator load is returned to a negative supply, the output must be diode-clamped to ground.
The output PMOS structure contains a diode between the VIN and VOUT terminals. This diode is normally reverse biased. This diode will
get forward biased if the voltage at the output terminal is forced to be higher than the voltage at the input terminal. This diode can
typically withstand 200mA of DC current and 1Amp of peak current.
Operating Ratings
(1)
2.5V to 7.0V
Shutdown Input Voltage
−0.3V to 7.0V
Input Supply Voltage
Maximum Operating Current (DC)
3A
−40°C to +125°C
Junction Temperature
(1)
The minimum operating value for VIN is equal to either [VOUT(NOM) + VDROPOUT] or 2.5V, whichever is greater.
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LP3853 LP3856
3
LP3853, LP3856
SNVS173G – FEBRUARY 2003 – REVISED APRIL 2013
www.ti.com
Electrical Characteristics
LP3853/LP3856
Limits in standard typeface are for TJ = 25°C, and limits in boldface type apply over the full operating temperature range.
Unless otherwise specified: VIN = VO(NOM) + 1V, IL = 10 mA, COUT = 10µF, VSD = 2V.
Symbol
VO
ΔV OL
ΔVO/ ΔIOUT
VIN - VOUT
IGND
Parameter
Output Voltage Tolerance
(3)
Output Voltage Line Regulation
(3)
Output Voltage Load Regulation
(3)
Dropout Voltage
Conditions
Typ
(1)
LP3853/6
Min
Max
-1.5
-3.0
+1.5
+3.0
Units
VOUT +1V ≤ VIN ≤ 7.0V
10 mA ≤ IL ≤ 3A
0
VOUT +1V ≤ VIN ≤ 7.0V
0.02
0.06
%
10 mA ≤ IL ≤ 3A
0.08
0.14
%
IL = 300 mA
39
50
65
IL = 3A
390
450
600
IL = 300 mA
4
9
10
IL = 3A
4
9
10
0.01
10
(4)
Ground Pin Current In Normal
Operation Mode
(2)
IGND
Ground Pin Current In Shutdown
Mode
VSD ≤ 0.3V
IO(PK)
Peak Output Current
VO ≥ VO(NOM) - 4%
-40°C ≤ TJ ≤ 85°C
50
%
mV
mA
µA
4.5
A
6
A
Short Circuit Protection
ISC
Short Circuit Current
Shutdown Input
VSDT
Shutdown Threshold
VSDT Rising from 0.3V until
Output = ON
1.3
VSDT Falling from 2.0V until
Output = OFF
1.3
2
V
0.3
TdOFF
Turn-off delay
IL = 3A
20
µs
TdON
Turn-on delay
IL = 3A
25
µs
SD Input Current
VSD = VIN
1
nA
ISD
Error Flag
Threshold
(5)
VTH
Threshold Hysteresis
(5)
VEF(Sat)
Error Flag Saturation
VT
(4)
(5)
4
5
5
2
0.02
16
%
8
%
0.1
V
Td
Flag Reset Delay
1
µs
Ilk
Error Flag Pin Leakage Current
1
nA
1
mA
Imax
(1)
(2)
(3)
Isink = 100µA
10
Error Flag Pin Sink Current
VError = 0.5V
Typical numbers are at 25°C and represent the most likely parametric norm.
Limits are ensured by testing, design, or statistical correlation.
Output voltage line regulation is defined as the change in output voltage from the nominal value due to change in the input line voltage.
Output voltage load regulation is defined as the change in output voltage from the nominal value due to change in load current. The line
and load regulation specification contains only the typical number. However, the limits for line and load regulation are included in the
output voltage tolerance specification.
Dropout voltage is defined as the minimum input to output differential voltage at which the output drops 2% below the nominal value.
Dropout voltage specification applies only to output voltages of 2.5V and above. For output voltages below 2.5V, the drop-out voltage is
nothing but the input to output differential, since the minimum input voltage is 2.5V.
Error Flag threshold and hysteresis are specified as percentage of regulated output voltage. See Application Hints.
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LP3853 LP3856
LP3853, LP3856
www.ti.com
SNVS173G – FEBRUARY 2003 – REVISED APRIL 2013
Electrical Characteristics
LP3853/LP3856 (continued)
Limits in standard typeface are for TJ = 25°C, and limits in boldface type apply over the full operating temperature range.
Unless otherwise specified: VIN = VO(NOM) + 1V, IL = 10 mA, COUT = 10µF, VSD = 2V.
Symbol
Parameter
Conditions
Typ
(1)
LP3853/6
Min
(2)
Max
Units
AC Parameters
PSRR
Ripple Rejection
ρn(l/f
Output Noise Density
en
Output Noise Voltage
VIN = VOUT + 1V
COUT = 10uF
VOUT = 3.3V, f = 120Hz
73
VIN = VOUT + 0.5V
COUT = 10uF
VOUT = 3.3V, f = 120Hz
57
f = 120Hz
0.8
BW = 10Hz – 100kHz
VOUT = 2.5V
150
BW = 300Hz – 300kHz
VOUT = 2.5V
100
dB
µV
µV (rms)
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LP3853 LP3856
5
LP3853, LP3856
SNVS173G – FEBRUARY 2003 – REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics
Unless otherwise specified: TJ = 25°C, COUT = 10µF, CIN = 10µF, S/D pin is tied to VIN, VOUT = 2.5V,
VIN = VO(NOM) + 1V, IL = 10 mA.
Ground Current
vs
Output Load Current
VOUT = 5V
Dropout Voltage
vs
Output Load Current
600
o
12
5
4.9
C
o
25
400
300
o
-40
GROUND PIN CURRENT (mA)
DROPOUT VOLTAGE (mV)
500
C
C
200
100
0
0
1
2
3
4.85
4.8
4.75
4.7
125oC
4.65
25oC
4.6
4.55
-40oC
4.5
4.45
4.4
LOAD CURRENT (A)
0
0.5
1
1.5
2
2.5
3
OUTPUT LOAD CURRENT (A)
Figure 5.
Figure 6.
Ground Current
vs
Output Voltage
IL = 3A
Shutdown IQ
vs
Junction Temperature
10
5
1
SHUTDOWN IQ (PA)
GROUND PIN CURRENT (mA)_
6
4
3
2
0.1
0.01
1
0
1.8
2.3
2.8
3.3
3.8
4.3
0.001
-40 -20
5.0
0
20
40
60
80
100 125
TEMPERATURE (oC)
Figure 7.
Figure 8.
Errorflag Threshold
vs
Junction Temperature
DC Load Reg.
vs
Junction Temperature
14
3
12
2.5
DC LOAD REGULATION (mV/A)
ERROR THRESHOLD (% of VOUT)
OUTPUT VOLTAGE (V)
10
8
6
4
2
2
1.5
1
0.5
0
-40 -20
0
20
40
60
80 100 125
0
-40
-20
0
20
40
60
80
100 125
o
JUNCTION TEMPERATURE ( C)
o
JUNCTION TEMPERATURE ( C)
Figure 9.
6
Figure 10.
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LP3853 LP3856
LP3853, LP3856
www.ti.com
SNVS173G – FEBRUARY 2003 – REVISED APRIL 2013
Typical Performance Characteristics (continued)
Unless otherwise specified: TJ = 25°C, COUT = 10µF, CIN = 10µF, S/D pin is tied to VIN, VOUT = 2.5V,
VIN = VO(NOM) + 1V, IL = 10 mA.
VIN
vs
VOUT Over Temperature
3
3.0
2.5
2.5
2
2.0
VOUT (V)
' VOUT/VOLT CHANGE in VIN (mV)
DC Line Regulation
vs
Temperature
1.5
1.5
-40oC
1
1.0
0.5
0.5
0
-40
25oC
125oC
0.0
-20
0
20
40
60
80
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
100 125
VIN (V)
o
JUNCTION TEMPERATURE ( C)
Figure 11.
Figure 12.
Noise
vs
Frequency
Load Transient Response
CIN = COUT = 10µF, OSCON
3.000
VOUT
100mV/DIV
2.500
MAGNITUDE
NOISE (PV/ Hz
(
IL = 100mA
CIN = COUT = 10PF
2.000
1.500
1.000
ILOAD
1A/DIV
0.500
0.000
100
1k
10k
TIME (50Ps/DIV)
100k
FREQUENCY (Hz)
Figure 13.
Figure 14.
Load Transient Response
CIN = COUT = 100µF, OSCON
Load Transient Response
CIN = COUT = 100µF, POSCAP
VOUT
100mV/DIV
MAGNITUDE
MAGNITUDE
VOUT
100mV/DIV
ILOAD
1A/DIV
ILOAD
1A/DIV
TIME (50Ps/DIV)
TIME (50Ps/DIV)
Figure 15.
Figure 16.
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LP3853 LP3856
7
LP3853, LP3856
SNVS173G – FEBRUARY 2003 – REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics (continued)
Unless otherwise specified: TJ = 25°C, COUT = 10µF, CIN = 10µF, S/D pin is tied to VIN, VOUT = 2.5V,
VIN = VO(NOM) + 1V, IL = 10 mA.
Load Transient Response
CIN = COUT = 10µF, TANTALUM
Load Transient Response
CIN = COUT = 100µF, TANTALUM
VOUT
100mV/DIV
MAGNITUDE
MAGNITUDE
VOUT
100mV/DIV
ILOAD
1A/DIV
ILOAD
1A/DIV
TIME (50Ps/DIV)
TIME (50Ps/DIV)
Figure 17.
Figure 18.
Load Transient Response
CIN = COUT = 10µF, OSCON
Load Transient Response
CIN = COUT = 100µF, OSCON
VOUT
100mV/DIV
MAGNITUDE
MAGNITUDE
VOUT
100mV/DIV
ILOAD
3A/DIV
ILOAD
3A/DIV
TIME (50Ps/DIV)
TIME (50Ps/DIV)
Figure 19.
Figure 20.
Load Transient Response
CIN = COUT = 100µF, POSCAP
Load Transient Response
CIN = COUT = 10µF, TANTALUM
VOUT
100mV/DIV
MAGNITUDE
MAGNITUDE
VOUT
100mV/DIV
ILOAD
3A/DIV
8
ILOAD
3A/DIV
TIME (50Ps/DIV)
TIME (50Ps/DIV)
Figure 21.
Figure 22.
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LP3853 LP3856
LP3853, LP3856
www.ti.com
SNVS173G – FEBRUARY 2003 – REVISED APRIL 2013
Typical Performance Characteristics (continued)
Unless otherwise specified: TJ = 25°C, COUT = 10µF, CIN = 10µF, S/D pin is tied to VIN, VOUT = 2.5V,
VIN = VO(NOM) + 1V, IL = 10 mA.
Load Transient Response
CIN = COUT = 100µF, TANTALUM
Load Transient Response
CIN = 4 x 10µF CERAMIC, COUT = 3 x 10µF CERAMIC
VOUT
100 mV/DIV
VOUT
100mV/DIV
VOUT = 2.5V
1
MAGNITUDE
T
IOUT
1A/DIV
ILOAD
3A/DIV
T
2
TIME (50Ps/DIV)
TIME (5 Ps/DIV)
Figure 23.
Figure 24.
Load Transient Response
CIN = 4 x 10µF CERAMIC, COUT = 3 x 10µF CERAMIC
Load Transient Response
CIN = 2 x 10µF CERAMIC, COUT = 2 x 10µF CERAMIC
VOUT
100 mV/DIV
VOUT
100 mV/DIV
VOUT = 2.5V
T
1
IOUT
1A/DIV
T
VOUT = 2.5V
1
T
IOUT
1A/DIV
T
IOUT
@ 1A
2
2
TIME (2 Ps/DIV)
TIME (1 Ps/DIV)
Figure 25.
Figure 26.
Load Transient Response
CIN = 2 x 10µF CERAMIC, COUT = 2 x 10µF CERAMIC
1
VOUT
@ 2.5V
T
IOUT
@ 1A
T
2
TIME (1 Ps/DIV)
Figure 27.
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LP3853 LP3856
9
LP3853, LP3856
SNVS173G – FEBRUARY 2003 – REVISED APRIL 2013
www.ti.com
APPLICATION INFORMATION
Application Hints
EXTERNAL CAPACITORS
Like any low-dropout regulator, external capacitors are required to assure stability. These capacitors must be
correctly selected for proper performance.
INPUT CAPACITOR: An input capacitor of at least 10µF is required. Ceramic or Tantalum may be used, and
capacitance may be increased without limit
OUTPUT CAPACITOR: An output capacitor is required for loop stability. It must be located less than 1 cm from
the device and connected directly to the output and ground pins using traces which have no other currents
flowing through them (see PCB Layout section).
The minimum amount of output capacitance that can be used for stable operation is 10µF. For general usage
across all load currents and operating conditions, the part was characterized using a 10µF Tantalum input
capacitor. The minimum and maximum stable ESR range for the output capacitor was then measured which kept
the device stable, assuming any output capacitor whose value is greater than 10µF (see Figure 28 below).
10
STABLE REGION
COUT > 10PF
COUT ESR (:)
1.0
0.1
.01
.001
0
1
2
3
LOAD CURRENT (A)
Figure 28. ESR Curve for COUT (with 10µF Tantalum Input Capacitor)
It should be noted that it is possible to operate the part with an output capacitor whose ESR is below these limits,
assuming that sufficient ceramic input capacitance is provided. This will allow stable operation using ceramic
output capacitors (see next section).
OPERATION WITH CERAMIC OUTPUT CAPACITORS
LP385X voltage regulators can operate with ceramic output capacitors if the values of input and output
capacitors are selected appropriately. The total ceramic output capacitance must be equal to or less than a
specified maximum value in order for the regulator to remain stable over all operating conditions. This maximum
amount of ceramic output capacitance is dependent upon the amount of ceramic input capacitance used as well
as the load current of the application. This relationship is shown in Figure 29, which graphs the maximum stable
value of ceramic output capacitance as a function of ceramic input capacitance for load currents of 1A, 2A, and
3A. For example, if the maximum load current is 1A, a 10µF ceramic input capacitor will allow stable operation
for values of ceramic output capacitance from 10µF up to about 500µF.
10
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LP3853 LP3856
LP3853, LP3856
www.ti.com
SNVS173G – FEBRUARY 2003 – REVISED APRIL 2013
CERAMIC INPUT CAPACITANCE (PF)
100
3A
2A
1A
10
10
100
1000
MAX. ALLOWABLE CERAMIC
OUTPUT CAPACITANCE (PF)
Figure 29. Maximum Ceramic Output Capacitance vs Ceramic Input Capacitance
If the maximum load current is 2A and a 10µF ceramic input capacitor is used, the regulator will be stable with
ceramic output capacitor values from 10µF up to about 50µF. At 3A of load current, the ratio of input to output
capacitance required approaches 1:1, meaning that whatever amount of ceramic output capacitance is used
must also be provided at the input for stable operation. For load currents between 1A, 2A, and 3A, interpolation
may be used to approximate values on the graph. When calculating the total ceramic output capacitance present
in an application, it is necessary to include any ceramic bypass capacitors connected to the regulator output.
SELECTING A CAPACITOR
It is important to note that capacitance tolerance and variation with temperature must be taken into consideration
when selecting a capacitor so that the minimum required amount of capacitance is provided over the full
operating temperature range. In general, a good Tantalum capacitor will show very little capacitance variation
with temperature, but a ceramic may not be as good (depending on dielectric type). Aluminum electrolytics also
typically have large temperature variation of capacitance value.
Equally important to consider is a capacitor's ESR change with temperature: this is not an issue with ceramics,
as their ESR is extremely low. However, it is very important in Tantalum and aluminum electrolytic capacitors.
Both show increasing ESR at colder temperatures, but the increase in aluminum electrolytic capacitors is so
severe they may not be feasible for some applications (see Capacitor Characteristics Section).
CAPACITOR CHARACTERISTICS
CERAMIC: For values of capacitance in the 10 to 100 µF range, ceramics are usually larger and more costly
than tantalums but give superior AC performance for bypassing high frequency noise because of very low ESR
(typically less than 10 mΩ). However, some dielectric types do not have good capacitance characteristics as a
function of voltage and temperature.
Z5U and Y5V dielectric ceramics have capacitance that drops severely with applied voltage. A typical Z5U or
Y5V capacitor can lose 60% of its rated capacitance with half of the rated voltage applied to it. The Z5U and Y5V
also exhibit a severe temperature effect, losing more than 50% of nominal capacitance at high and low limits of
the temperature range.
X7R and X5R dielectric ceramic capacitors are strongly recommended if ceramics are used, as they typically
maintain a capacitance range within ±20% of nominal over full operating ratings of temperature and voltage. Of
course, they are typically larger and more costly than Z5U/Y5U types for a given voltage and capacitance.
TANTALUM: Solid Tantalum capacitors are typically recommended for use on the output because their ESR is
very close to the ideal value required for loop compensation.
Tantalums also have good temperature stability: a good quality Tantalum will typically show a capacitance value
that varies less than 10-15% across the full temperature range of 125°C to −40°C. ESR will vary only about 2X
going from the high to low temperature limits.
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LP3853 LP3856
11
LP3853, LP3856
SNVS173G – FEBRUARY 2003 – REVISED APRIL 2013
www.ti.com
The increasing ESR at lower temperatures can cause oscillations when marginal quality capacitors are used (if
the ESR of the capacitor is near the upper limit of the stability range at room temperature).
ALUMINUM: This capacitor type offers the most capacitance for the money. The disadvantages are that they are
larger in physical size, not widely available in surface mount, and have poor AC performance (especially at
higher frequencies) due to higher ESR and ESL.
Compared by size, the ESR of an aluminum electrolytic is higher than either Tantalum or ceramic, and it also
varies greatly with temperature. A typical aluminum electrolytic can exhibit an ESR increase of as much as 50X
when going from 25°C down to −40°C.
It should also be noted that many aluminum electrolytics only specify impedance at a frequency of 120 Hz, which
indicates they have poor high frequency performance. Only aluminum electrolytics that have an impedance
specified at a higher frequency (between 20 kHz and 100 kHz) should be used for the LP385X. Derating must be
applied to the manufacturer's ESR specification, since it is typically only valid at room temperature.
Any applications using aluminum electrolytics should be thoroughly tested at the lowest ambient operating
temperature where ESR is maximum.
TURN-ON CHARACTERISTICS FOR OUTPUT VOLTAGES PROGRAMMED TO 2.0V OR BELOW
As Vin increases during start-up, the regulator output will track the input until Vin reaches the minimum operating
voltage (typically about 2.2V). For output voltages programmed to 2.0V or below, the regulator output may
momentarily exceed its programmed output voltage during start up. Outputs programmed to voltages above 2.0V
are not affected by this behavior.
PCB LAYOUT
Good PC layout practices must be used or instability can be induced because of ground loops and voltage drops.
The input and output capacitors must be directly connected to the input, output, and ground pins of the regulator
using traces which do not have other currents flowing in them (Kelvin connect).
The best way to do this is to lay out CIN and COUT near the device with short traces to the VIN, VOUT, and ground
pins. The regulator ground pin should be connected to the external circuit ground so that the regulator and its
capacitors have a "single point ground".
It should be noted that stability problems have been seen in applications where "vias" to an internal ground plane
were used at the ground points of the IC and the input and output capacitors. This was caused by varying ground
potentials at these nodes resulting from current flowing through the ground plane. Using a single point ground
technique for the regulator and it's capacitors fixed the problem.
Since high current flows through the traces going into VIN and coming from VOUT, Kelvin connect the capacitor
leads to these pins so there is no voltage drop in series with the input and output capacitors.
RFI/EMI SUSCEPTIBILITY
RFI (radio frequency interference) and EMI (electromagnetic interference) can degrade any integrated circuit's
performance because of the small dimensions of the geometries inside the device. In applications where circuit
sources are present which generate signals with significant high frequency energy content (> 1 MHz), care must
be taken to ensure that this does not affect the IC regulator.
If RFI/EMI noise is present on the input side of the regulator (such as applications where the input source comes
from the output of a switching regulator), good ceramic bypass capacitors must be used at the input pin of the IC.
If a load is connected to the IC output which switches at high speed (such as a clock), the high-frequency current
pulses required by the load must be supplied by the capacitors on the IC output. Since the bandwidth of the
regulator loop is less than 100 kHz, the control circuitry cannot respond to load changes above that frequency.
This means the effective output impedance of the IC at frequencies above 100 kHz is determined only by the
output capacitor(s).
In applications where the load is switching at high speed, the output of the IC may need RF isolation from the
load. It is recommended that some inductance be placed between the output capacitor and the load, and good
RF bypass capacitors be placed directly across the load.
12
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LP3853 LP3856
LP3853, LP3856
www.ti.com
SNVS173G – FEBRUARY 2003 – REVISED APRIL 2013
PCB layout is also critical in high noise environments, since RFI/EMI is easily radiated directly into PC traces.
Noisy circuitry should be isolated from "clean" circuits where possible, and grounded through a separate path. At
MHz frequencies, ground planes begin to look inductive and RFI/EMI can cause ground bounce across the
ground plane.
In multi-layer PCB applications, care should be taken in layout so that noisy power and ground planes do not
radiate directly into adjacent layers which carry analog power and ground.
OUTPUT NOISE
Noise is specified in two waysSpot Noise or Output noise density is the RMS sum of all noise sources, measured at the regulator output, at
a specific frequency (measured with a 1Hz bandwidth). This type of noise is usually plotted on a curve as a
function of frequency.
Total output Noise or Broad-band noise is the RMS sum of spot noise over a specified bandwidth, usually
several decades of frequencies.
Attention should be paid to the units of measurement. Spot noise is measured in units µV/√Hz or nV/√Hz and
total output noise is measured in µV(rms).
The primary source of noise in low-dropout regulators is the internal reference. In CMOS regulators, noise has a
low frequency component and a high frequency component, which depend strongly on the silicon area and
quiescent current. Noise can be reduced in two ways: by increasing the transistor area or by increasing the
current drawn by the internal reference. Increasing the area will decrease the chance of fitting the die into a
smaller package. Increasing the current drawn by the internal reference increases the total supply current
(ground pin current). Using an optimized trade-off of ground pin current and die size, LP3853/LP3856 achieves
low noise performance and low quiescent current operation.
The total output noise specification for LP3853/LP3856 is presented in the Electrical Characteristics table. The
Output noise density at different frequencies is represented by a curve under typical performance characteristics.
SHORT-CIRCUIT PROTECTION
The LP3853 and LP3856 are short circuit protected and in the event of a peak over-current condition, the shortcircuit control loop will rapidly drive the output PMOS pass element off. Once the power pass element shuts
down, the control loop will rapidly cycle the output on and off until the average power dissipation causes the
thermal shutdown circuit to respond to servo the on/off cycling to a lower frequency. Please refer to the section
on thermal information for power dissipation calculations.
ERROR FLAG OPERATION
The LP3853/LP3856 produces a logic low signal at the Error Flag pin when the output drops out of regulation
due to low input voltage, current limiting, or thermal limiting. This flag has a built in hysteresis. The timing
diagram in Figure 30 shows the relationship between the ERROR flag and the output voltage. In this example,
the input voltage is changed to demonstrate the functionality of the Error Flag.
The internal Error flag comparator has an open drain output stage. Hence, the ERROR pin should be pulled high
through a pull up resistor. Although the ERROR flag pin can sink current of 1mA, this current is energy drain
from the input supply. Hence, the value of the pull up resistor should be in the range of 10kΩ to 1MΩ. The
ERROR pin must be connected to ground if this function is not used. It should also be noted that when the
shutdown pin is pulled low, the ERROR pin is forced to be invalid for reasons of saving power in shutdown
mode.
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LP3853 LP3856
13
LP3853, LP3856
SNVS173G – FEBRUARY 2003 – REVISED APRIL 2013
www.ti.com
Figure 30. Error Flag Operation
SENSE PIN
In applications where the regulator output is not very close to the load, LP3856 can provide better remote load
regulation using the SENSE pin. Figure 31 depicts the advantage of the SENSE option. LP3853 regulates the
voltage at the output pin. Hence, the voltage at the remote load will be the regulator output voltage minus the
drop across the trace resistance. For example, in the case of a 3.3V output, if the trace resistance is 100mΩ, the
voltage at the remote load will be 3V with 3A of load current, ILOAD. The LP3856 regulates the voltage at the
sense pin. Connecting the sense pin to the remote load will provide regulation at the remote load, as shown in
Figure 31. If the sense option pin is not required, the sense pin must be connected to the VOUT pin.
Figure 31. Improving remote load regulation using LP3856
14
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LP3853 LP3856
LP3853, LP3856
www.ti.com
SNVS173G – FEBRUARY 2003 – REVISED APRIL 2013
SHUTDOWN OPERATION
A CMOS Logic low level signal at the Shutdown (SD) pin will turn-off the regulator. Pin SD must be actively
terminated through a 10kΩ pull-up resistor for a proper operation. If this pin is driven from a source that actively
pulls high and low (such as a CMOS rail to rail comparator), the pull-up resistor is not required. This pin must be
tied to Vin if not used.
The Shutdown (SD) pin threshold has no voltage hysteresis. If the Shutdown pin is actively driven, the voltage
transition must rise and fall cleanly and promptly.
DROPOUT VOLTAGE
The dropout voltage of a regulator is defined as the minimum input-to-output differential required to stay within
2% of the nominal output voltage. For CMOS LDOs, the dropout voltage is the product of the load current and
the Rds(on) of the internal MOSFET.
REVERSE CURRENT PATH
The internal MOSFET in LP3853 and LP3856 has an inherent parasitic diode. During normal operation, the input
voltage is higher than the output voltage and the parasitic diode is reverse biased. However, if the output is
pulled above the input in an application, then current flows from the output to the input as the parasitic diode gets
forward biased. The output can be pulled above the input as long as the current in the parasitic diode is limited to
200mA continuous and 1A peak.
POWER DISSIPATION/HEATSINKING
LP3853 and LP3856 can deliver a continuous current of 3A over the full operating temperature range. A heatsink
may be required depending on the maximum power dissipation and maximum ambient temperature of the
application. Under all possible conditions, the junction temperature must be within the range specified under
operating conditions. The total power dissipation of the device is given by:
PD = (VIN−VOUT)IOUT+ (VIN)IGND
where IGND is the operating ground current of the device (specified under Electrical Characteristics).
The maximum allowable temperature rise (TRmax) depends on the maximum ambient temperature (TAmax) of the
application, and the maximum allowable junction temperature (TJmax):
TRmax = TJmax− TAmax
The maximum allowable value for junction to ambient Thermal Resistance, θJA, can be calculated using the
formula:
θJA = TRmax / PD
LP3853 and LP3856 are available in TO-220 and TO-263 packages. The thermal resistance depends on amount
of copper area or heat sink, and on air flow. If the maximum allowable value of θJA calculated above is ≥ 60 °C/W
for TO-220 package and ≥ 60 °C/W for TO-263 package no heatsink is needed since the package can dissipate
enough heat to satisfy these requirements. If the value for allowable θJA falls below these limits, a heat sink is
required.
HEATSINKING TO-220 PACKAGE
The thermal resistance of a TO220 package can be reduced by attaching it to a heat sink or a copper plane on a
PC board. If a copper plane is to be used, the values of θJA will be same as shown in next section for TO263
package.
The heatsink to be used in the application should have a heatsink to ambient thermal resistance,
θHA≤ θJA − θCH − θJC.
In this equation, θCH is the thermal resistance from the case to the surface of the heat sink and θJC is the thermal
resistance from the junction to the surface of the case. θJC is about 3°C/W for a TO220 package. The value for
θCH depends on method of attachment, insulator, etc. θCH varies between 1.5°C/W to 2.5°C/W. If the exact value
is unknown, 2°C/W can be assumed.
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LP3853 LP3856
15
LP3853, LP3856
SNVS173G – FEBRUARY 2003 – REVISED APRIL 2013
www.ti.com
HEATSINKING TO-263 PACKAGE
The TO-263 package uses the copper plane on the PCB as a heatsink. The tab of these packages are soldered
to the copper plane for heat sinking. Figure 32 shows a curve for the θJA of TO-263 package for different copper
area sizes, using a typical PCB with 1 ounce copper and no solder mask over the copper area for heat sinking.
Figure 32. θJA vs Copper (1 Ounce) Area for TO-263 package
As shown in the figure, increasing the copper area beyond 1 square inch produces very little improvement. The
minimum value for θJA for the TO-263 package mounted to a PCB is 32°C/W.
Figure 33 shows the maximum allowable power dissipation for TO-263 packages for different ambient
temperatures, assuming θJA is 35°C/W and the maximum junction temperature is 125°C.
Figure 33. Maximum power dissipation vs ambient temperature for TO-263 package
16
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LP3853 LP3856
LP3853, LP3856
www.ti.com
SNVS173G – FEBRUARY 2003 – REVISED APRIL 2013
REVISION HISTORY
Changes from Revision F (April 2013) to Revision G
•
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 16
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LP3853 LP3856
17
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LP3853ES-1.8
NRND
DDPAK/
TO-263
KTT
5
45
TBD
Call TI
Call TI
-40 to 125
LP3853ES
-1.8
LP3853ES-1.8/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LP3853ES
-1.8
LP3853ES-2.5
NRND
DDPAK/
TO-263
KTT
5
45
TBD
Call TI
Call TI
-40 to 125
LP3853ES
-2.5
LP3853ES-2.5/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LP3853ES
-2.5
LP3853ES-3.3
NRND
DDPAK/
TO-263
KTT
5
45
TBD
Call TI
Call TI
-40 to 125
LP3853ES
-3.3
LP3853ES-3.3/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LP3853ES
-3.3
LP3853ES-5.0/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LP3853ES
-5.0
LP3853ESX-1.8/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
500
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LP3853ES
-1.8
LP3853ESX-2.5/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
500
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LP3853ES
-2.5
LP3853ESX-3.3/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
500
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LP3853ES
-3.3
LP3853ESX-5.0/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
500
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LP3853ES
-5.0
LP3853ET-1.8/NOPB
ACTIVE
TO-220
NDH
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
-40 to 125
LP3853ET
-1.8
LP3853ET-2.5/NOPB
ACTIVE
TO-220
NDH
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
-40 to 125
LP3853ET
-2.5
LP3853ET-3.3/NOPB
ACTIVE
TO-220
NDH
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
-40 to 125
LP3853ET
-3.3
LP3853ET-5.0/NOPB
ACTIVE
TO-220
NDH
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
-40 to 125
LP3853ET
-5.0
LP3856ES-1.8
NRND
DDPAK/
TO-263
KTT
5
45
TBD
Call TI
Call TI
-40 to 125
LP3856ES
-1.8
LP3856ES-1.8/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LP3856ES
-1.8
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
1-Nov-2013
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LP3856ES-2.5/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LP3856ES
-2.5
LP3856ES-3.3
NRND
DDPAK/
TO-263
KTT
5
45
TBD
Call TI
Call TI
-40 to 125
LP3856ES
-3.3
LP3856ES-3.3/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LP3856ES
-3.3
LP3856ES-5.0
NRND
DDPAK/
TO-263
KTT
5
45
TBD
Call TI
Call TI
-40 to 125
LP3856ES
-5.0
LP3856ES-5.0/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LP3856ES
-5.0
LP3856ESX-1.8/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
500
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LP3856ES
-1.8
LP3856ESX-2.5/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
500
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LP3856ES
-2.5
LP3856ESX-3.3/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
500
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LP3856ES
-3.3
LP3856ESX-5.0/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
500
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LP3856ES
-5.0
LP3856ET-1.8/NOPB
ACTIVE
TO-220
NDH
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
-40 to 125
LP3856ET
-1.8
LP3856ET-2.5/NOPB
ACTIVE
TO-220
NDH
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
-40 to 125
LP3856ET
-2.5
LP3856ET-3.3/NOPB
ACTIVE
TO-220
NDH
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
-40 to 125
LP3856ET
-3.3
LP3856ET-5.0/NOPB
ACTIVE
TO-220
NDH
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
-40 to 125
LP3856ET
-5.0
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Addendum-Page 2
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
LP3853ESX-1.8/NOPB
DDPAK/
TO-263
KTT
5
500
330.0
24.4
10.75
14.85
5.0
16.0
24.0
Q2
LP3853ESX-2.5/NOPB
DDPAK/
TO-263
KTT
5
500
330.0
24.4
10.75
14.85
5.0
16.0
24.0
Q2
LP3853ESX-3.3/NOPB
DDPAK/
TO-263
KTT
5
500
330.0
24.4
10.75
14.85
5.0
16.0
24.0
Q2
LP3853ESX-5.0/NOPB
DDPAK/
TO-263
KTT
5
500
330.0
24.4
10.75
14.85
5.0
16.0
24.0
Q2
LP3856ESX-1.8/NOPB
DDPAK/
TO-263
KTT
5
500
330.0
24.4
10.75
14.85
5.0
16.0
24.0
Q2
LP3856ESX-2.5/NOPB
DDPAK/
TO-263
KTT
5
500
330.0
24.4
10.75
14.85
5.0
16.0
24.0
Q2
LP3856ESX-3.3/NOPB
DDPAK/
TO-263
KTT
5
500
330.0
24.4
10.75
14.85
5.0
16.0
24.0
Q2
LP3856ESX-5.0/NOPB
DDPAK/
TO-263
KTT
5
500
330.0
24.4
10.75
14.85
5.0
16.0
24.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LP3853ESX-1.8/NOPB
DDPAK/TO-263
KTT
5
500
367.0
367.0
45.0
LP3853ESX-2.5/NOPB
DDPAK/TO-263
KTT
5
500
367.0
367.0
45.0
LP3853ESX-3.3/NOPB
DDPAK/TO-263
KTT
5
500
367.0
367.0
45.0
LP3853ESX-5.0/NOPB
DDPAK/TO-263
KTT
5
500
367.0
367.0
45.0
LP3856ESX-1.8/NOPB
DDPAK/TO-263
KTT
5
500
367.0
367.0
45.0
LP3856ESX-2.5/NOPB
DDPAK/TO-263
KTT
5
500
367.0
367.0
45.0
LP3856ESX-3.3/NOPB
DDPAK/TO-263
KTT
5
500
367.0
367.0
45.0
LP3856ESX-5.0/NOPB
DDPAK/TO-263
KTT
5
500
367.0
367.0
45.0
Pack Materials-Page 2
MECHANICAL DATA
NDH0005D
www.ti.com
MECHANICAL DATA
KTT0005B
TS5B (Rev D)
BOTTOM SIDE OF PACKAGE
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
Similar pages