GWSEMI FRF1605CT 16.0 amp fast recovery rectifier Datasheet

FRF1601CT
THRU
FRF1606CT
16.0 AMP FAST RECOVERY RECTIFIERS
VOLTAGE RANGE
50 to 800 Volts
CURRENT
16.0 Amperes
FEATURES
* Low forward voltage drop
* High current capability
* High reliability
* High surge current capability
ITO-220(FULLY INSULATED)
.108
(2.75)
.248
(6.3)
MECHANICAL DATA
* Case: Molded plastic
* Epoxy: UL 94V-0 rate flame retardant
* Lead: Lead solderable per MIL-STD-202,
method 208 guranteed
* Polarity: As Marked
* Mounting position: Any
.189
MAX.
(4.8)
.122
MAX.
(3.1)
3.4 f MAX.
HOLE THRU
.412
(10.5)
MAX.
.610
(15.5)
MAX.
.550
(14.0)
.158
(4.0) MIN.
MAX.
.060 MAX.
(1.5)
.035 MAX.
(0.9)
.100
(2.54)
.114(2.9)
.098(2.5)
PIN 1
+
PIN 3
CASE
PIN 2
Dimensions in inches and (millimeters)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating 25 C ambient temperature uniess otherwies specified.
Single phase half wave, 60Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
TYPE NUMBER
FRF
1601CT
FRF
1602CT
50
35
50
100
70
100
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Voltage
Maximum DC Blocking Voltage
Maximum Average Forward Rectified Current
FRF
1603CT
FRF
1604CT
200
140
200
400
280
400
FRF
1605CT
600
420
600
FRF
1606CT UNITS
800
560
800
V
V
V
at Tc=75 C
Peak Forward Surge Current, 8.3 ms single half sine-wave
16.0
A
superimposed on rated load (JEDEC method)
Maximum Instantaneous Forward Voltage at 8.0A
Maximum DC Reverse Current
Tc=25 C
150
1.3
10.0
A
V
A
200
at Rated DC Blocking Voltage
Tc=100 C
Maximum Reverse Recovery Time (Note 1)
Typical Junction Capacitance (Note 2)
Operating and Storage Temperature Range TJ, TSTG
250
150
-65
NOTES:
1. Reverse Recovery Time test condition: IF=0.5A, IR=1.0A, IRR=0.25A
2. Measured at 1MHz and applied reverse voltage of 4.0V D.C.
196
65
+150
500
A
nS
pF
C
RATING AND CHARACTERISTIC CURVES (FRF1601CT THRU FRF1606CT)
FIG.1-TYPICAL FORWARD
FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE
AVERAGE FORWARD CURRENT,(A)
CHARACTERISTICS
100
40
10
24
20
16
Single Phase
12
Half Wave 60Hz
Resistive Or Inductive Load
8
4
0
0
20
40
60
Tj=25 C
80
100
120
140
160
180
200
CASE TEMPERATURE ( C)
Pulse Width 300us
1% Duty Cycle
1
0.1
.6
.8
1.0
1.2
1.4
1.6
1.8
2.0
FORWARD VOLTAGE,(V)
FIG.3- TEST CIRCUIT DIAGRAM AND REVERSE
RECOVERY TIME CHARACTERISTICS
50W
NONINDUCTIVE
10W
NONINDUCTIVE
( )
(+)
D.U.T.
25Vdc
(approx.)
PEAK FORWARD SURGE CURRENT,(A)
FIG.4-MAXIMUM NON-REPETITIVE FORWARD
SURGE CURRENT
PULSE
GENERATOR
(NOTE 2)
( )
250
200
150
Sine Wave
100
JEDEC method
50
1
5
(+)
1W
NONINDUCTIVE
2. Rise Time= 10ns max., Source Impedance= 50 ohms.
|
|
|
|
|
|
|
|
0
-0.25A
100
FIG.5-TYPICAL JUNCTION CAPACITANCE
NOTES: 1. Rise Time= 7ns max., Input Impedance= 1 megohm.22pF.
+0.5A
50
10
NUMBER OF CYCLES AT 60Hz
OSCILLISCOPE
(NOTE 1)
trr
8.3ms Single Half
Tj=25 C
0
140
JUNCTION CAPACITANCE,(pF)
INSTANTANEOUS FORWARD CURRENT,(A)
500
120
100
80
60
40
20
0
-1.0A
1cm
.01
SET TIME BASE FOR
.05
.1
.5
1
REVERSE VOLTAGE,(V)
50 / 10ns / cm
197
5
10
50
100
Similar pages