Hirose HNC-2.5S-D-B 2.5mm pitch connector for discrete wire connection Datasheet

2.5mm Pitch Connector for Discrete Wire Connection
HNC Series
■Features
1. Full Lock Mechanism
The connector is equipped with the full lock mechanism so as not be removed, unless locks are reset on both sides. This mechanism is
activated effectively to prevent cable hooking or mis-insertion.
2. Thin Type Connector
Mounting height when the connector is used at the right angle :
4.5mm
3. Mechanism to Prevent Mis-insertion
This thin type connector is equipped with the mechanism to prevent misinsertion.
4. Tin Plating and Gold Plating Variation
Two kinds of tin plating and gold plating types are available, and can be
chosen according to application. The tin plating is also set to a light operating
touch.
■Applications
Various business equipment, financial terminals
Thickness
4.5mm
Mechanism
to prevent
false-insertion
Full lock
mechanism
B139
■Product Specifications
AWG 22 : 3A
AWG 24 : 3A
Current rating
Rating
AWG 26 : 2A
(Note1)
AWG 28 : 1A
AWG 30 : 0.5A
Voltage rating
250V AC
Item
Operating Temperature Range
-25 to +85ç (Note2)
Operating Moisture Range
-40 to 80%
Storage Temperature Range
-10 to +60ç (Note3)
Storage Moisture Range
-40 to 70% (Note3)
Specification
Condition
1. Insulation Resistance
1000M ohms min.
500V DC
2. Withstanding voltage
No flashover or insulation breakdown.
1000V AC/1 minute
3. Contact Resistance
30m ohms Max
1A
4. Insertor/Extraction Force 0.4N (40gf) min.,4.4N (450gf) max.
Measure at the square steel pin of 0.635±0.002mm
5. Vibration
Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 2 hours in each of the 3 directions.
No electrical discontinuity of 1µs or more
6. Humidity (Steady state) Contact resistance: 10m ohms max.Insulation resistance: 1000M ohms min. 96 hours at temperature of 40ç and humidity of 90% to 95%
7. Temperature Cycle
Contact resistance: 10m ohms max:Insulation resistance: 1000M ohms min.
(-85ç: 30 minutes ➝ 5 to 35ç: 10 minutes) 5 cycles
Tin plating
8. Durability (Mating/un-mating) Contact resistance: 20m ohms max.
9. Resistance to Soldering heat
(-25ç: 30 minutes ➝ 5 to 35ç: 10 minutes
: 30 cycles
Gold plating : 50 cycles
Flow: 250ç for 5 seconds
No deformation of components affecting performance.
Manual soldering: 300ç for 2 seconds
Note 1: The rated current will be changed according to cable sizes for use. The header rating only t is 3A.
Note 2: Includes temperature rise caused by current flow.
Note 3: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range
and Humidity range covers non conducting condition of installed connectors in storage, shipment or during transportation.
■Material
Product
Crimping Socket
Contact
Pin Header
Part
Insulator
Contact
Insulator
Contact
Material
Polyamide
Phosphor Copper
Polyamide
Brass
Finish
Black
Tin plated or gold plated
Black
Tin plated or gold plated
■Ordering Information
●Crimping Plug
HNC 2 - 2.5 P - * DSL
q
q Series Name
w Series No.
e Contact Pitch
r Connector Type
S : Socket
P : Pin Header
●Contact
w
e
: HNC
: 2, 1
: 2.5mm
t
y
t Number of Contacts : 2 to 16, 18, 20
y Contact Type
None : Crimping socket
DS
: Straight
DSL : Right angle
HNC2 - 2.5S - C - A
q
q Type: 2.5mm pitch socket
w Packaging Type
C : Reel
PC : Bag
B140
r
w
e
e Applicable cable size
A
: AWG22 to 26
B
: AWG26 to 30
Remarks
UL94V-0
–––––
UL94V-0
–––––
■Crimping Socket
[Figure 1]
[Figure 2]
Unit: mm
Part Number
CL No.
Number of Contacts
A
B
C
HNC2-2.5S- 2(**)
218-0011-1-**
2
12.4
6
2.5
HNC2-2.5S- 3(**)
218-0022-8-**
3
14.9
8.5
5
HNC2-2.5S- 4(**)
218-0039-0-**
4
17.4
11
HNC2-2.5S- 5(**)
218-0027-1-**
5
19.9
13.5
10
HNC2-2.5S- 6(**)
218-0042-5-**
6
22.4
16
12.5
HNC2-2.5S- 7(**)
218-0030-6-**
7
24.9
18.5
15
HNC2-2.5S- 8(**)
218-0014-0-**
8
27.4
21
17.5
HNC2-2.5S-10(**)
218-0017-8-**
10
32.4
26
22.5
HNC1-2.5S-12(**)
218-0008-7-**
12
37
31
27.5
Dimensions
[Specific No.] –* *, (* *)
Blank :Bag packaging
7.5
Figure 1
Figure 2
Figure 1
15
44.9 38.5 35
HNC2-2.5S-15(**)
218-0045-3-**
Note1: Please order a quantity multiplied by 100 pcs. (Not per bag, but per pcs.)
Note2: The series name of 12 contacts connector is HNC1, and partially will be changed in the
style.
B141
■Straight Pin Header
[Figure 3]
+
●Board Through-hole Diameter: ø1.1+00.1
[Figure 4]
Unit: mm
Part Number
CL No.
Number of Contacts
A
HNC2-2.5P- 2DS(**)
218-0012-4-**
2
12.5
HNC2-2.5P- 3DS(**)
218-0023-0-**
3
15
10.4
HNC2-2.5P- 4DS(**)
218-0040-0-**
4
17.5
12.9
HNC2-2.5P- 5DS(**)
218-0028-4-**
5
20
15.4
10
HNC2-2.5P- 6DS(**)
218-0043-8-**
6
22.5
17.9
HNC2-2.5P- 7DS(**)
218-0031-9-**
7
25
HNC2-2.5P- 8DS(**)
218-0015-2-**
8
HNC2-2.5P-10DS(**)
218-0018-0-**
10
HNC1-2.5P-12DS(**)
218-0009-0-**
12
B
C
7.8
Specific No.
Gold plating
2.5
Blank
02
5
Blank
02
7.5
Blank
01
Blank
02
12.5
Blank
01
20.4
15
Blank
02
27.5
22.8
17.5
Blank
02
32.5
27.8
22.5
Blank
02
35.5
32.8
27.5
Blank
02
Figure 4
01
Figure 3
40.4 35
Blank
15
45
HNC2-2.5P-15DS(**) 218-0046-6-**
Note1: Please order a quantity multiplied by 100 pcs. (Not per bag, but per piece)
Note2: The series name of the 12 contacts connector is HNC1 and the style will be partially changed.
B142
Dimensions
Tin plating
Figure 3
■Right Angle Pin Header
[Figure 5]
+
●Board Through-hole Diameter: ø1.1+00.1
[Figure 6]
Unit: mm
Part Number
CL No.
Number of Contacts
A
HNC2-2.5P- 2DSL(**)
218-0013-7-**
2
12.5
HNC2-2.5P- 3DSL(**)
218-0024-3-**
3
15
10.4
B
C
7.8
Specific No.
Tin plating
Gold plating
2.5
Blank
02
5
Blank
02
7.5
HNC2-2.5P- 4DSL(**)
218-0041-2-**
4
17.5
12.9
Blank
01
HNC2-2.5P- 5DSL(**)
218-0029-7-**
5
20
15.4
10
Blank
02
HNC2-2.5P- 6DSL(**)
218-0044-0-**
6
22.5
17.9
12.5
Blank
01
HNC2-2.5P- 7DSL(**)
218-0032-1-**
7
25
20.4
15
Blank
02
Dimensions
Figure 5
HNC2-2.5P- 8DSL(**)
218-0016-5-**
8
27.5
22.8
17.5
Blank
02
HNC2-2.5P-10DSL(**)
218-0019-3-**
10
32.5
27.8
22.5
Blank
02
HNC1-2.5P-12DSL(**)
218-0010-9-**
12
35.5
32.8
27.5
Blank
02
Figure 6
01
Figure 5
40.4 35
Blank
15
45
HNC2-2.5P-15DSL(**) 218-0047-9-**
Note1: Please order a quantity multiplied by 100 pcs. (Not per bag, but per piece)
Note2: The series name of the 12 contacts connector is HNC1 and the style will be partially changed.
B143
■Crimping Contact for Socket
●Applicable Cable (Tin Plated Annealing Copper Wire)
Conductor Size (Contact wire construction) Jacket Diameter
●Recommended Cable
UL1061, UL1007
AWG 22 (17pieces/0.16mm)
AWG 24 (11pieces/0.16mm)
Ø1.35 to Ø1.7mm
●Strip Length
2.8 to 3.3mm
AWG 26 (07pieces/0.16mm)
AWG 28 (07pieces/0.127mm)
AWG 30 (07pieces/0.1mm)
Ø1.0 to Ø1.35mm
Note: If other cables are used instead of the applicable
cable, please contact Hirose sales department.
Unit: mm
Part Number
CL No.
HNC-2.5S-D-A(**)
218-0037-5-**
HNC-2.5S-C-A(**)
218-0021-5-**
HNC-2.5S-D-B(**)
218-0038-8-**
HNC-2.5S-C-B(**)
218-0020-2-**
Conductor
Jacket
Size
Diameter
A
AWG 22 to 26 Ø1.35 to 1.7mm
AWG 26 to 30 Ø1.0 to 1.35mm
B
Packaging
Type
Quantity
1.8 2.6
Bag
100
1.8 2.6
Reel
10,000
1.5 1.7
Bag
100
1.5 1.7
Reel
10,000
Specific No.
Tin plating
Gold plating
Blank
02
■Applicable Crimping Tool
Type
Applicator
Press Main Unit
Manual Crimping Tool
Extraction Tool
Part Number
CL No.
Applicable Contact
AP105-HNC
901-4502-0
HNC-2.5S-C-A/HNC-2.5S-C-B
CM105
901-0005-4
––––––––––––––––––––––––
TC-HNC-B
250-0005-7
HNC-2.5S-D-B
TC-HNC-A
250-0006-0
HNC-2.5S-D-A
DF1-C-PO
550-0177-7
HNC-2.5S-C-A/HNC-2.5S-C-B
Note: If a trouble has occurred due to tools which are not designated by Hirose, Hirose won't guarantee any product.
■Application Pattern
B144
BPrecautions
1. Recommended Soldering Condition
Flow: 250ç for 3 seconds
2. Cleaning Condition
Refer to Nylon Connector Use Hand book.
Manual soldering: 290ç for 2 seconds
3. Connection Condition
Refer to Nylon Connector Use Hand book.
●Extracting Crimping Contact
To extract the crimping contact from the socket housing, observe the following extraction
procedures.
■Extraction Tool
Tool Name: DF-C-PO(550-0177-7) can be used.
(1) Extraction Method
As shown below in the figure, slightly pull the cable in the state where the DF1 extraction
tool tip or the 0.5 to 0.7mm board has been inserted in the lance fixed slot, the contact can
be easily removed.
Note: If the lance is pressed excessively, the contact body may be deformed, which could
result in contact failure. Therefore, be careful not to press the lance excessively.
(2) How to Adjust the Lance (Raise)
To re-insert the terminal which is removed from the socket housing, use a sharp edge
blade to raise the lance as shown below in the illustration, and then insert the contact.
Note: Lance regeneration is effective only once.
B145
Similar pages