TI1 LMK62E2-156M25SIAR High-performance low jitter oscillator Datasheet

Order
Now
Product
Folder
Support &
Community
Tools &
Software
Technical
Documents
LMK62E2-156M, LMK62E0-156M, LMK62A2-100M, LMK62A2-150M
LMK62A2-156M, LMK62A2-200M, LMK62A2-266M
SNAS691B – DECEMBER 2016 – REVISED JUNE 2017
LMK62XX High-Performance Low Jitter Oscillator
1 Features
3 Description
•
The LMK62XX device is a low jitter oscillator that
generates a commonly used reference clock. The
device is pre-programmed in factory to support any
reference clock frequency; supported output formats
are LVPECL, LVDS and HCSL up to 400 MHz.
Internal power conditioning provide excellent power
supply ripple rejection (PSRR), reducing the cost and
complexity of the power delivery network. The device
operates from a single 3.3-V ±5% supply.
1
•
•
•
•
•
Low Noise, High Performance
– Jitter: 150 fs RMS typical Fout > 100 MHz
– PSRR: –60 dBc, Robust Supply Noise
Immunity
Supported Output Format
– LVPECL, LVDS and HCSL up to 400 MHz
Total Frequency Tolerance of ±50 ppm
(LMK62X2) and ±25 ppm (LMK62X0)
3.3-V Operating Voltage
Industrial Temperature Range (–40ºC to +85ºC)
5-mm × 3.2-mm 6-pin Package That is PinCompatible With Industry Standard 5032 XO
Package
Device Information(1)
PART NUMBER
PACKAGE
BODY SIZE (NOM)
LMK62E2-156M
QFM (6)
5.00 mm × 3.20 mm
LMK62E0-156M
QFM (6)
5.00 mm × 3.20 mm
LMK62A2-100M
QFM (6)
5.00 mm × 3.20 mm
LMK62A2-150M
QFM (6)
5.00 mm × 3.20 mm
2 Applications
LMK62A2-156M
QFM (6)
5.00 mm × 3.20 mm
•
LMK62A2-200M
QFM (6)
5.00 mm × 3.20 mm
LMK62A2-266M
QFM (6)
5.00 mm × 3.20 mm
•
•
•
•
High-Performance Replacement for Crystal-,
SAW-, or Silicon-based Oscillators
Switches, Routers, Network Line Cards, Base
Band Units (BBU), Servers, Storage/SAN
Test and Measurement
Medical Imaging
FPGA, Processor Attach
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Output Frequency Options
PART NUMBER
OUTPUT FREQ
(MHz) AND FORMAT
TOTAL FREQ
STABILITY (ppm)
LMK62E2-156M
156.25 LVPECL
±50
LMK62E0-156M
156.25 LVPECL
±25
LMK62A2-100M
100 LVDS
±50
LMK62A2-150M
150 LVDS
±50
LMK62A2-156M
156.25 LVDS
±50
LMK62A2-200M
200 LVDS
±50
LMK62A2-266M
266.66 LVDS
±50
Pinout
6
OE
1
6
VDD
NC
2
5
OUTN
GND
3
4
OUTP
1
2
5
4
3
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LMK62E2-156M, LMK62E0-156M, LMK62A2-100M, LMK62A2-150M
LMK62A2-156M, LMK62A2-200M, LMK62A2-266M
SNAS691B – DECEMBER 2016 – REVISED JUNE 2017
www.ti.com
Table of Contents
1
2
3
4
5
6
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
3
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
6.10
3
3
4
4
4
4
5
5
5
5
Absolute Maximum Ratings ......................................
ESD Ratings ............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics - Power Supply .................
LVPECL Output Characteristics................................
LVDS Output Characteristics ....................................
HCSL Output Characteristics....................................
OE Input Characteristics ...........................................
Frequency Tolerance Characteristics .....................
6.11
6.12
6.13
6.14
Power-On/Reset Characteristics (VDD)..................
PSRR Characteristics .............................................
PLL Clock Output Jitter Characteristics ..................
Additional Reliability and Qualification ....................
6
6
6
6
7
Parameter Measurement Information .................. 7
8
9
Power Supply Recommendations........................ 9
Layout ..................................................................... 9
7.1 Device Output Configurations ................................... 7
9.1 Layout Guidelines ..................................................... 9
10 Device and Documentation Support ................. 11
10.1
10.2
10.3
10.4
10.5
Receiving Notification of Documentation Updates
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
11
11
11
11
11
11 Mechanical, Packaging, and Orderable
Information ........................................................... 11
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision A (April 2017) to Revision B
•
Page
Added the LMK62E0-156M, LMK62A2-100M, LMK62A2-150M, LMK62A2-156M, LMK62A2-200M, and LMK62A2266M to device list.................................................................................................................................................................. 1
Changes from Original (December 2016) to Revision A
•
2
Page
Updated advanced information data sheet to production data .............................................................................................. 1
Submit Documentation Feedback
Copyright © 2016–2017, Texas Instruments Incorporated
Product Folder Links: LMK62E2-156M LMK62E0-156M LMK62A2-100M LMK62A2-150M LMK62A2-156M LMK62A2200M LMK62A2-266M
LMK62E2-156M, LMK62E0-156M, LMK62A2-100M, LMK62A2-150M
LMK62A2-156M, LMK62A2-200M, LMK62A2-266M
www.ti.com
SNAS691B – DECEMBER 2016 – REVISED JUNE 2017
5 Pin Configuration and Functions
SIA Package
6-pin QFM
Top View
OE
1
6
VDD
NC
2
5
OUTN
GND
3
4
OUTP
Pin Functions
PIN
NAME
I/O
NO.
DESCRIPTION
POWER
GND
3
Ground
Device ground
VDD
6
Analog
3.3-V power supply
4, 5
Universal
OUTPUT BLOCK
OUTP,
OUTN
Differential output pair (LVPECL, LVDS or HCSL).
DIGITAL CONTROL / INTERFACES
NC
2
N/A
OE
1
LVCMOS
No connect
Output enable (internal pullup). When set to low, output pair is disabled and set at high
impedance.
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1)
MIN
MAX
UNIT
VDD
Device supply voltage
–0.3
3.6
V
VIN
Output voltage for logic inputs
–0.3
VDD + 0.3
V
VOUT
Output voltage for clock outputs
–0.3
VDD + 0.3
V
TJ
Junction temperature
150
°C
Tstg
Storage temperature
125
°C
(1)
–40
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute maximum-rated conditions for extended periods may affect device reliability.
6.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Electrostatic
discharge
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1)
±2000
Charged-device model (CDM), per JEDEC specification JESD22-C101 (2)
±500
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
Copyright © 2016–2017, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LMK62E2-156M LMK62E0-156M LMK62A2-100M LMK62A2-150M LMK62A2-156M LMK62A2200M LMK62A2-266M
3
LMK62E2-156M, LMK62E0-156M, LMK62A2-100M, LMK62A2-150M
LMK62A2-156M, LMK62A2-200M, LMK62A2-266M
SNAS691B – DECEMBER 2016 – REVISED JUNE 2017
www.ti.com
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
VDD
Device supply voltage
TA
Ambient temperature
TJ
Junction temperature
tRAMP
VDD power-up ramp time
MIN
NOM
MAX
3.135
3.3
3.465
V
–40
25
85
°C
0.1
UNIT
105
°C
100
ms
6.4 Thermal Information
LMK62XX
(2) (3) (4)
SIA (QFM )
THERMAL METRIC (1)
UNIT
6 PINS
Airflow (LFM) 0
RθJA
Junction-to-ambient thermal resistance
94.5
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
65.1
°C/W
RθJB
Junction-to-board thermal resistance
59
°C/W
ψJT
Junction-to-top characterization parameter
23.3
°C/W
ψJB
Junction-to-board characterization parameter
64.1
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
n/a
°C/W
(1)
(2)
(3)
(4)
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
The package thermal resistance is calculated on a 4-layer JEDEC board.
Connected to GND with 2 thermal vias (0.3-mm diameter).
ψJB (junction to board) is used when the main heat flow is from the junction to the GND pad. Please refer to Thermal Considerations
section for more information on ensuring good system reliability and quality.
6.5 Electrical Characteristics - Power Supply (1)
VDD = 3.3 V ± 5%, TA = –40°C to 85°C
PARAMETER
IDD
Device current consumption
Device current consumption
when output is disabled
IDD-PD
(1)
(2)
(3)
TEST CONDITIONS
TYP
MAX
LVPECL (2)
MIN
95
110
LVDS
85
100
HCSL (3)
90
105
OE = GND
70
UNIT
mA
mA
Refer to Parameter Measurement Information for relevant test conditions.
On-chip power dissipation should exclude 40 mW, dissipated in the 150-Ω termination resistors, from total power dissipation.
Excludes load current.
6.6 LVPECL Output Characteristics (1)
VDD = 3.3 V ± 5%, TA = –40°C to 85°C
PARAMETER
fOUT
Output frequency (2)
VOD
Output voltage swing (VOH – VOL) (2)
VOUT, DIFF, PP
Differential output peak-to-peak swing
VOS
Output common-mode voltage
tR / tF
Output rise/fall time (20% to 80%) (3)
ODC
Output duty cycle (3)
(1)
(2)
(3)
4
TEST CONDITIONS
MIN
TYP
700
950
MAX
UNIT
400
MHz
1200
mV
2 × |VOD|
V
VDD – 1.45
260
45%
V
350
ps
55%
Refer to Parameter Measurement Information for relevant test conditions.
An output frequency over fOUT max spec is possible, but output swing may be less than VOD min spec.
Ensured by characterization.
Submit Documentation Feedback
Copyright © 2016–2017, Texas Instruments Incorporated
Product Folder Links: LMK62E2-156M LMK62E0-156M LMK62A2-100M LMK62A2-150M LMK62A2-156M LMK62A2200M LMK62A2-266M
LMK62E2-156M, LMK62E0-156M, LMK62A2-100M, LMK62A2-150M
LMK62A2-156M, LMK62A2-200M, LMK62A2-266M
www.ti.com
SNAS691B – DECEMBER 2016 – REVISED JUNE 2017
6.7 LVDS Output Characteristics (1)
VDD = 3.3 V ± 5%, TA = –40°C to 85°C
PARAMETER
TEST CONDITIONS
MIN
TYP
300
390
(1)
fOUT
Output frequency
VOD
Output voltage swing (VOH - VOL) (1)
UNIT
400
MHz
480
mV
2x
|VOD|
VOUT, DIFF, PP
Differential output peak-to-peak swing
VOS
Output common-mode voltage
1.2
tR / tF
Output rise/fall time (20% to 80%) (2)
260
ODC
Output duty cycle (2)
ROUT
Differential output impedance
(1)
(2)
MAX
V
V
350
45%
ps
55%
107
Ω
An output frequency over fOUT max spec is possible, but output swing may be less than VOD min spec.
Ensured by characterization.
6.8 HCSL Output Characteristics (1)
VDD = 3.3 V ± 5%, TA = –40°C to 85°C
PARAMETER
fOUT
Output frequency
VOH
Output high voltage
VOL
Output low voltage
VCROSS
Absolute crossing voltage (2) (3)
TEST CONDITIONS
VCROSS-DELTA Variation of VCROSS (2) (3)
dV/dt
Slew rate (4)
ODC
Output duty cycle (4)
(1)
(2)
(3)
(4)
MIN
TYP
MAX
UNIT
400
MHz
660
900
mV
–100
100
mV
250
475
mV
0
140
mV
1
3
V/ns
45%
55%
Refer to Parameter Measurement Information for relevant test conditions.
Measured from -150 mV to +150 mV on the differential waveform with the 300 mVpp measurement window centered on the differential
zero crossing.
Ensured by design.
Ensured by characterization.
6.9 OE Input Characteristics
VDD = 3.3 V ± 5%, TA = –40°C to 85°C
PARAMETER
TEST CONDITIONS
MIN
VIH
Input high voltage
VIL
Input low voltage
IIH
Input high current
VIH = VDD
–40
IIL
Input low current
VIL = GND
–40
CIN
Input capacitance
TYP
MAX
UNIT
1.4
V
0.6
V
40
µA
40
µA
2
pF
6.10 Frequency Tolerance Characteristics (1)
VDD = 3.3 V ± 5%, TA = –40°C to 85°C
PARAMETER
fT
(1)
Total frequency tolerance
TEST CONDITIONS
MIN
LMK62X2: All output formats, frequency
bands and device junction temperature up to
105°C; includes initial freq tolerance,
temperature & supply voltage variation, solder
reflow and 5-year aging at 40°C
LMK62X0: All output formats, frequency
bands and device junction temperature up to
105°C; includes initial freq tolerance,
temperature & supply voltage variation, solder
reflow and 5-year aging at 40°C
TYP
MAX
UNIT
–50
50
ppm
–25
25
ppm
Ensured by characterization.
Copyright © 2016–2017, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LMK62E2-156M LMK62E0-156M LMK62A2-100M LMK62A2-150M LMK62A2-156M LMK62A2200M LMK62A2-266M
5
LMK62E2-156M, LMK62E0-156M, LMK62A2-100M, LMK62A2-150M
LMK62A2-156M, LMK62A2-200M, LMK62A2-266M
SNAS691B – DECEMBER 2016 – REVISED JUNE 2017
www.ti.com
6.11 Power-On/Reset Characteristics (VDD)
VDD = 3.3 V ± 5%, TA = –40°C to 85°C
PARAMETER
TEST CONDITIONS
MIN
(1)
VTHRESH
Threshold voltage
VDROOP
Allowable voltage droop (2)
TYP
MAX
2.85
(1)
UNIT
3
V
0.1
V
Time elapsed from VDD at 3.135 V to
output enabled
10
ms
tSTARTUP
Start-up time
tOE-EN
Output enable time (2)
Time elapsed from OE at VIH to
output enabled
50
µs
tOE-DIS
Output disable time (2)
Time elapsed from OE at VIL to
output disabled
50
µs
(1)
(2)
Ensured by characterization.
Ensured by design.
6.12 PSRR Characteristics (1)
VDD = 3.3 V, TA = 25°C
PARAMETER
PSRR
(1)
(2)
(3)
Spurs induced by 50-mV
power supply ripple (2) (3) at
156.25-MHz output, all
output types
TEST CONDITIONS
MIN
TYP
Sine wave at 50 kHz
–60
Sine wave at 100 kHz
–60
Sine wave at 500 kHz
–60
Sine wave at 1 MHz
–60
MAX
UNIT
dBc
Refer to Parameter Measurement Information for relevant test conditions.
Measured max spur level with 50 mVpp sinusoidal signal between 50 kHz and 1 MHz applied on VDD pin
DJSPUR (ps, pk-pk) = [2*10(SPUR/20) / (π*fOUT)]*1e6, where PSRR or SPUR in dBc and fOUT in MHz.
6.13 PLL Clock Output Jitter Characteristics (1) (2)
VDD = 3.3 V ± 5%, TA = –40°C to 85°C
PARAMETER
RJ
(1)
(2)
(3)
RMS phase jitter (3)
(12 kHz – 20 MHz)
TEST CONDITIONS
fOUT ≥ 100 MHz, all output types
MIN
TYP
MAX
UNIT
150
250
fs RMS
Refer to Parameter Measurement Information for relevant test conditions.
Phase jitter measured with Agilent E5052 signal source analyzer using a differential-to-single ended converter (balun or buffer).
Ensured by characterization.
6.14 Additional Reliability and Qualification
6
PARAMETER
CONDITION / TEST METHOD
Mechanical Shock
MIL-STD-202, Method 213
Mechanical Vibration
MIL-STD-202, Method 204
Moisture Sensitivity Level
J-STD-020, MSL3
Submit Documentation Feedback
Copyright © 2016–2017, Texas Instruments Incorporated
Product Folder Links: LMK62E2-156M LMK62E0-156M LMK62A2-100M LMK62A2-150M LMK62A2-156M LMK62A2200M LMK62A2-266M
LMK62E2-156M, LMK62E0-156M, LMK62A2-100M, LMK62A2-150M
LMK62A2-156M, LMK62A2-200M, LMK62A2-266M
www.ti.com
SNAS691B – DECEMBER 2016 – REVISED JUNE 2017
7 Parameter Measurement Information
7.1 Device Output Configurations
High impedance differential probe
LMK62XX
LVPECL
150
Oscilloscope
150
Copyright © 2017, Texas Instruments Incorporated
Figure 1. LVPECL Output DC Configuration During Device Test
High impedance differential probe
LMK62XX
LVDS
Oscilloscope
Copyright © 2017, Texas Instruments Incorporated
Figure 2. LVDS Output DC Configuration During Device Test
High impedance differential probe
HCSL
LMK62XX
50
Oscilloscope
50
Copyright © 2017, Texas Instruments Incorporated
Figure 3. HCSL Output DC Configuration During Device Test
LMK62XX
Balun/
Buffer
LVPECL
150
(1)
Phase Noise/
Spectrum
Analyzer
150
Copyright © 2017, Texas Instruments Incorporated
Figure 4. LVPECL Output AC Configuration During Device Test
(1)
Also compatible with 85 Ω termination
Copyright © 2016–2017, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LMK62E2-156M LMK62E0-156M LMK62A2-100M LMK62A2-150M LMK62A2-156M LMK62A2200M LMK62A2-266M
7
LMK62E2-156M, LMK62E0-156M, LMK62A2-100M, LMK62A2-150M
LMK62A2-156M, LMK62A2-200M, LMK62A2-266M
SNAS691B – DECEMBER 2016 – REVISED JUNE 2017
www.ti.com
Device Output Configurations (continued)
LMK62XX
Balun/
Buffer
LVDS
Phase Noise/
Spectrum
Analyzer
Copyright © 2017, Texas Instruments Incorporated
Figure 5. LVDS Output AC Configuration During Device Test
LMK62XX
Balun/
Buffer
HCSL
50
Phase Noise/
Spectrum
Analyzer
50
Copyright © 2017, Texas Instruments Incorporated
Figure 6. HCSL Output AC Configuration During Device Test
Sine wave
Modulator
Power Supply
LMK62XX
Balun
150 (LVPECL)
Open (LVDS)
50 (HCSL)
Phase Noise/
Spectrum
Analyzer
150 (LVPECL)
Open (LVDS)
50 (HCSL)
Copyright © 2017, Texas Instruments Incorporated
Figure 7. PSRR Test Setup
OUT_P
VOD
OUT_N
80%
VOUT,DIFF,PP = 2 x VOD
0V
20%
tR
tF
Figure 8. Differential Output Voltage and Rise/Fall Time
8
Submit Documentation Feedback
Copyright © 2016–2017, Texas Instruments Incorporated
Product Folder Links: LMK62E2-156M LMK62E0-156M LMK62A2-100M LMK62A2-150M LMK62A2-156M LMK62A2200M LMK62A2-266M
LMK62E2-156M, LMK62E0-156M, LMK62A2-100M, LMK62A2-150M
LMK62A2-156M, LMK62A2-200M, LMK62A2-266M
www.ti.com
SNAS691B – DECEMBER 2016 – REVISED JUNE 2017
8 Power Supply Recommendations
For best electrical performance of LMK62XX, TI recommends using a combination of 10 µF, 1 µF, and 0.1 µF on
the power-supply bypass network of the device. TI also recommends using component side mounting of the
power-supply bypass capacitors and it is best to use 0201 or 0402 body size capacitors to facilitate signal
routing. Keep the connections between the bypass capacitors and the power supply on the device as short as
possible. Ground the other side of the capacitor using a low impedance connection to the ground plane. Figure 9
shows the layout recommendation for power supply decoupling of LMK62XX.
9 Layout
9.1 Layout Guidelines
The following sections provides recommendations for board layout, solder reflow profile and power supply
bypassing when using LMK62XX to ensure good thermal / electrical performance and overall signal integrity of
entire system.
9.1.1 Ensuring Thermal Reliability
The LMK62XX is a high-performance device. Therefore, pay careful attention to the device configuration and
printed-circuit board (PCB) layout with respect to power consumption. The ground pin must be connected to the
ground plane of the PCB through three vias or more, as shown in Figure 9, to maximize thermal dissipation out
of the package.
Equation 1 shows the relationship between the PCB temperature around the LMK62XX and the junction
temperature.
TB = TJ – ΨJB × P
where
•
•
•
•
TB: PCB temperature around the LMK62XX
TJ: Junction temperature of LMK62XX
ΨJB: Junction-to-board thermal resistance parameter of LMK62XX (64.1°C/W without airflow)
P: On-chip power dissipation of LMK62XX
(1)
To ensure that the maximum junction temperature of LMK62XX is below 105°C, it can be calculated that the
maximum PCB temperature without airflow should be at 81°C or below when the device is optimized for best
performance, resulting in maximum on-chip power dissipation of 0.36 W.
9.1.2 Best Practices for Signal Integrity
For best electrical performance and signal integrity of entire system with LMK62XX, TI recommends routing vias
into decoupling capacitors and then into the LMK62XX. TI also recommends increasing the via count and width
of the traces wherever possible. These steps ensure lowest impedance and shortest path for high frequency
current flow. Figure 9 shows the layout recommendation for LMK62XX.
Copyright © 2016–2017, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LMK62E2-156M LMK62E0-156M LMK62A2-100M LMK62A2-150M LMK62A2-156M LMK62A2200M LMK62A2-266M
9
LMK62E2-156M, LMK62E0-156M, LMK62A2-100M, LMK62A2-150M
LMK62A2-156M, LMK62A2-200M, LMK62A2-266M
SNAS691B – DECEMBER 2016 – REVISED JUNE 2017
www.ti.com
Layout Guidelines (continued)
Figure 9. LMK62XX Layout Recommendation for Power Supply and Ground
9.1.3 Recommended Solder Reflow Profile
TI recommends following the recommendations set by the solder paste supplier to optimize flux activity and to
achieve proper melting temperatures of the alloy within the guidelines of J-STD-20. Processing LMK62XX with
the lowest peak temperature possible while also remaining below the components peak temperature rating as
listed on the MSL label is preferred. The exact temperature profile would depend on several factors including
maximum peak temperature for the component as rated on the MSL label, board thickness, PCB material type,
PCB geometries, component locations, sizes, densities within PCB, as well as the recommended soldering
profile from the manufacturer, and capability of the reflow equipment to as confirmed by the SMT assembly
operation.
10
Submit Documentation Feedback
Copyright © 2016–2017, Texas Instruments Incorporated
Product Folder Links: LMK62E2-156M LMK62E0-156M LMK62A2-100M LMK62A2-150M LMK62A2-156M LMK62A2200M LMK62A2-266M
LMK62E2-156M, LMK62E0-156M, LMK62A2-100M, LMK62A2-150M
LMK62A2-156M, LMK62A2-200M, LMK62A2-266M
www.ti.com
SNAS691B – DECEMBER 2016 – REVISED JUNE 2017
10 Device and Documentation Support
10.1 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
10.2 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
10.3 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
10.4 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
10.5 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
11 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2016–2017, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LMK62E2-156M LMK62E0-156M LMK62A2-100M LMK62A2-150M LMK62A2-156M LMK62A2200M LMK62A2-266M
11
LMK62E2-156M, LMK62E0-156M, LMK62A2-100M, LMK62A2-150M
LMK62A2-156M, LMK62A2-200M, LMK62A2-266M
SNAS691B – DECEMBER 2016 – REVISED JUNE 2017
www.ti.com
PACKAGE OUTLINE
SIA0006B
QFM - 1.1 mm max height
SCALE 3.000
QUAD FLAT MODULE
3.3
3.1
B
A
PIN 1 INDEX
AREA
5.1
4.9
C
1.1 MAX
0.1 C
SEATING PLANE
2.1
6X (0.1)
3
4
2X
2.54
SYMM
4X
1.27
6
1
6X
SYMM
6X
0.67
0.61
0.1
0.05
C A B
C
0.93
0.87
4223058/A 06/2016
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
www.ti.com
12
Submit Documentation Feedback
Copyright © 2016–2017, Texas Instruments Incorporated
Product Folder Links: LMK62E2-156M LMK62E0-156M LMK62A2-100M LMK62A2-150M LMK62A2-156M LMK62A2200M LMK62A2-266M
LMK62E2-156M, LMK62E0-156M, LMK62A2-100M, LMK62A2-150M
LMK62A2-156M, LMK62A2-200M, LMK62A2-266M
www.ti.com
SNAS691B – DECEMBER 2016 – REVISED JUNE 2017
EXAMPLE BOARD LAYOUT
SIA0006B
QFM - 1.1 mm max height
QUAD FLAT MODULE
SYMM
6X (0.9)
6X (0.64) 1
6
SYMM
4X (1.27)
4
3
(R0.05) TYP
(2.1)
LAND PATTERN EXAMPLE
1:1 RATIO WITH PACKAGE SOLDER PADS
SCALE:15X
0.07 MIN
ALL AROUND
0.07 MAX
ALL AROUND
SOLDER MASK
OPENING
METAL
SOLDER MASK
OPENING
NON SOLDER MASK
DEFINED
METAL UNDER
SOLDER MASK
SOLDER MASK
DEFINED
SOLDER MASK DETAILS
NOT TO SCALE
4223058/A 06/2016
NOTES: (continued)
3. For more information, see Texas Instruments literature number SLUA271 (www.ti.com/lit/slua271).
www.ti.com
Copyright © 2016–2017, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: LMK62E2-156M LMK62E0-156M LMK62A2-100M LMK62A2-150M LMK62A2-156M LMK62A2200M LMK62A2-266M
13
LMK62E2-156M, LMK62E0-156M, LMK62A2-100M, LMK62A2-150M
LMK62A2-156M, LMK62A2-200M, LMK62A2-266M
SNAS691B – DECEMBER 2016 – REVISED JUNE 2017
www.ti.com
EXAMPLE STENCIL DESIGN
SIA0006B
QFM - 1.1 mm max height
QUAD FLAT MODULE
SYMM
6X (0.9)
6X (0.64)
(R0.05)
6
1
SYMM
4X (1.27)
4
3
(2.1)
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
PRINTED SOLDER COVERAGE BY AREA
ALL PADS: 100%
SCALE:15X
4223058/A 06/2016
NOTES: (continued)
4. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
www.ti.com
14
Submit Documentation Feedback
Copyright © 2016–2017, Texas Instruments Incorporated
Product Folder Links: LMK62E2-156M LMK62E0-156M LMK62A2-100M LMK62A2-150M LMK62A2-156M LMK62A2200M LMK62A2-266M
PACKAGE OPTION ADDENDUM
www.ti.com
11-Jul-2017
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LMK62A2-100M00SIAR
ACTIVE
QFM
SIA
6
2500
Green (RoHS
& no Sb/Br)
NIAU
Level-3-260C-168 HR
-40 to 85
62A2
10000
LMK62A2-100M00SIAT
ACTIVE
QFM
SIA
6
250
Green (RoHS
& no Sb/Br)
NIAU
Level-3-260C-168 HR
-40 to 85
62A2
10000
LMK62A2-150M00SIAR
ACTIVE
QFM
SIA
6
2500
Green (RoHS
& no Sb/Br)
NIAU
Level-3-260C-168 HR
-40 to 85
62A2
15000
LMK62A2-150M00SIAT
ACTIVE
QFM
SIA
6
250
Green (RoHS
& no Sb/Br)
NIAU
Level-3-260C-168 HR
-40 to 85
62A2
15000
LMK62A2-156M25SIAR
ACTIVE
QFM
SIA
6
2500
Green (RoHS
& no Sb/Br)
NIAU
Level-3-260C-168 HR
-40 to 85
62A2
15625
LMK62A2-156M25SIAT
ACTIVE
QFM
SIA
6
250
Green (RoHS
& no Sb/Br)
NIAU
Level-3-260C-168 HR
-40 to 85
62A2
15625
LMK62A2-200M00SIAR
ACTIVE
QFM
SIA
6
2500
Green (RoHS
& no Sb/Br)
NIAU
Level-3-260C-168 HR
-40 to 85
62A2
20000
LMK62A2-200M00SIAT
ACTIVE
QFM
SIA
6
250
Green (RoHS
& no Sb/Br)
NIAU
Level-3-260C-168 HR
-40 to 85
62A2
20000
LMK62A2-266M66SIAR
ACTIVE
QFM
SIA
6
2500
Green (RoHS
& no Sb/Br)
NIAU
Level-3-260C-168 HR
-40 to 85
62A2
26666
LMK62A2-266M66SIAT
ACTIVE
QFM
SIA
6
250
Green (RoHS
& no Sb/Br)
NIAU
Level-3-260C-168 HR
-40 to 85
62A2
26666
LMK62E0-156M25SIAR
ACTIVE
QFM
SIA
6
2500
Green (RoHS
& no Sb/Br)
NIAU
Level-3-260C-168 HR
-40 to 85
62E0
15625
LMK62E0-156M25SIAT
ACTIVE
QFM
SIA
6
250
Green (RoHS
& no Sb/Br)
NIAU
Level-3-260C-168 HR
-40 to 85
62E0
15625
LMK62E2-156M25SIAR
ACTIVE
QFM
SIA
6
2500
Green (RoHS
& no Sb/Br)
NIAU
Level-3-260C-168 HR
-40 to 85
62E2
15625
LMK62E2-156M25SIAT
ACTIVE
QFM
SIA
6
250
Green (RoHS
& no Sb/Br)
NIAU
Level-3-260C-168 HR
-40 to 85
62E2
15625
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
11-Jul-2017
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s noncompliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2017, Texas Instruments Incorporated
Similar pages