AD AD5553CRMZ Current output/serial input, 16-/14-bit dac Datasheet

Current Output/Serial Input,
16-/14-Bit DACs
AD5543/AD5553
Data Sheet
FEATURES
FUNCTIONAL BLOCK DIAGRAM
16-bit resolution AD5543
14-bit resolution AD5553
±1 LSB DNL
±1 LSB INL
Low noise: 12 nV/√Hz
Low power: IDD = 10 µA
0.5 µs settling time
4Q multiplying reference input
2 mA full-scale current ± 20%, with VREF = 10 V
Built-in RFB facilitates voltage conversion
3-wire interface
Ultracompact 8-lead MSOP and 8-lead SOIC packages
AD5543/AD5553
VREF
16 OR 14
CLK
GND
02917-001
16-BIT/14-BIT SHIFT
REGISTER
SDI
Figure 1.
1.0
0.8
0.6
INL (LSB)
0.4
0.2
0
–0.2
–0.4
–0.6
65,536
CODE
02917-002
61,440
57,344
53,248
49,152
45,056
40,960
36,864
32,768
28,672
24,575
20,480
16,384
8152
12,288
0
–1.0
4096
–0.8
The applied external reference, VREF, determines the full-scale
output current. An internal feedback resistor (RFB) facilitates the
R-2R and temperature tracking for voltage conversion when
combined with an external op amp.
Figure 2. Integral Nonlinearity
A serial-data interface offers high speed, 3-wire microcontrollercompatible inputs using serial data in (SDI), clock (CLK), and
chip select (CS).
2
0
–2
–4
GAIN (dB)
The AD5543/AD5553 are packaged in ultracompact (3 mm ×
4.7 mm) 8-lead MSOP and 8-lead SOIC packages.
DAC
REGISTER
CONTROL
LOGIC
CS
Automatic test equipment
Instrumentation
Digitally controlled calibration
Industrial control PLCs
The AD5543/AD5553 are precision 16-/14-bit, low power,
current output, small form factor digital-to-analog converters
(DACs). They are designed to operate from a single 5 V supply
with a ±10 V multiplying reference.
IOUT
DAC
16 OR 14
APPLICATIONS
GENERAL DESCRIPTION
RFB
VDD
–6
–8
–10
–14
10k
100k
1M
10M
FREQUENCY (Hz)
100M
02917-025
–12
Figure 3. Reference Multiplying Bandwidth
Rev. F
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©2002–2012 Analog Devices, Inc. All rights reserved.
AD5543/AD5553
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Applications Information .............................................................. 11
Applications ....................................................................................... 1
Stability ........................................................................................ 11
General Description ......................................................................... 1
Positive Voltage Output ............................................................. 11
Functional Block Diagram .............................................................. 1
Bipolar Output ............................................................................ 11
Revision History ............................................................................... 2
Programmable Current Source ................................................ 12
Specifications..................................................................................... 3
Reference Selection .................................................................... 12
Timing Diagrams.......................................................................... 4
Amplifier Selection .................................................................... 12
Absolute Maximum Ratings............................................................ 5
Evaluation Board ............................................................................ 14
ESD Caution .................................................................................. 5
System Development Platform ................................................. 14
Pin Configuration and Function Descriptions ............................. 6
AD5543/AD5553 to SPORT Interface .................................... 14
Typical Performance Characteristics ............................................. 7
Waveform Generator ................................................................. 14
Circuit Operation ............................................................................. 9
Operating the Evaluation Board .............................................. 14
DAC Section .................................................................................. 9
Bill of Materials ........................................................................... 18
Serial Data Interface ....................................................................... 10
Outline Dimensions ....................................................................... 19
ESD Protection Circuits............................................................. 10
Ordering Guide .......................................................................... 20
PCB Layout and Power Supply Bypassing .............................. 10
REVISION HISTORY
1/12—Rev. E to Rev. F
Added Figure 15, Renumbered Sequentially ................................ 8
Change to Table 9 ........................................................................... 13
Changes to Figure 27 ...................................................................... 15
Changes to Figure 28 ...................................................................... 16
Replaced Figure 29, Figure 30, and Figure 31 ............................. 17
2/11—Rev. D to Rev. E
Added Evaluation Board Section ................................................. 14
Updated Outline Dimensions ....................................................... 20
Changes to Ordering Guide .......................................................... 21
4/10—Rev. C to Rev. D
Changes to Figure 3 .......................................................................... 1
Changes to Table 1 ............................................................................ 3
Moved Timing Diagrams Section .................................................. 4
Moved Table 4 ................................................................................... 6
Delete Figure 13; Renumbered Sequentially ................................. 8
Changes to Figure 14 ........................................................................ 8
Changes to Figure 18 ........................................................................ 9
Moved Table 5 and Table 6 ............................................................ 10
Added Reference Selection Section and Amplifier Selection
Section .............................................................................................. 12
Added Table 7, Table 8, and Table 9;
Renumbered Sequentially.............................................................. 13
10/09—Rev. B to Rev. C
Updated Outline Dimensions..................................................... 14
Changes to Ordering Guide .......................................................... 15
7/09—Rev. A to Rev. B
Updated Format .................................................................. Universal
Change to Features Section ..............................................................1
Updated Outline Dimensions ....................................................... 14
Changes to Ordering Guide .......................................................... 15
2/03—Rev. 0 to Rev. A
Changes to Ordering Guide .............................................................3
12/02—Revision 0: Initial Version
Rev. F | Page 2 of 20
Data Sheet
AD5543/AD5553
SPECIFICATIONS
VDD = 5 V ± 10%, VSS = 0 V, IOUT = virtual GND, GND = 0 V, VREF = 10 V, TA = full operating temperature range, unless otherwise noted.
Table 1.
Parameter
STATIC PERFORMANCE 1
Resolution
Symbol
Condition
5 V ± 10%
Unit
N
1 LSB = VREF/216 = 153 µV when VREF = 10 V (AD5543)
1 LSB = VREF/214 = 610 µV when VREF = 10 V (AD5553)
Grade: AD5553C
Grade: AD5543C
Grade: AD5543B
Monotonic
Data = 0x0000, TA = 25°C
Data = 0x0000, TA = TA maximum
Data = 0xFFFF
16
14
±1
±1
±2
±1
10
20
±1/±4
1
Bits
Bits
LSB max
LSB max
LSB max
LSB max
nA max
nA max
mV typ/max
ppm/°C typ
−15/+15
5
5
V min/max
kΩ typ 3
pF typ
2
mA typ
200
pF typ
0.8
2.4
10
10
V max
V min
µA max
pF max
50
10
10
0
10
5
10
MHz
ns min
ns min
ns min
ns min
ns min
ns min
4.5/5.5
10
0.055
0.006
V min/max
µA max
mW max
%/% max
Relative Accuracy
INL
Differential Nonlinearity
Output Leakage Current
DNL
IOUT
Full-Scale Gain Error
Full-Scale Temperature Coefficient 2
REFERENCE INPUT
VREF Range
Input Resistance
Input Capacitance2
ANALOG OUTPUT
Output Current
GFSE
TCVFS
Output Capacitance2
LOGIC INPUTS AND OUTPUT
Logic Input Low Voltage
Logic Input High Voltage
Input Leakage Current
Input Capacitance2
INTERFACE TIMING2, 4
Clock Input Frequency
Clock Width High
Clock Width Low
CS to Clock Setup
Clock to CS Hold
Data Setup
Data Hold
SUPPLY CHARACTERISTICS
Power Supply Range
Positive Supply Current
Power Dissipation
Power Supply Sensitivity
COUT
VREF
RREF
CREF
IOUT
Data = 0xFFFF for AD5543
Data = 0x3FFF for AD5553
Code dependent
VIL
VIH
IIL
CIL
See Figure 4 and Figure 5
fCLK
tCH
tCL
tCSS
tCSH
tDS
tDH
VDD RANGE
IDD
PDISS
PSS
Logic inputs = 0 V
Logic inputs = 0 V
ΔVDD = ±5%
Rev. F | Page 3 of 20
AD5543/AD5553
Data Sheet
Parameter
AC CHARACTERISTICS4
Output Voltage Settling Time
Reference Multiplying Bandwidth
DAC Glitch Impulse
Feedthrough Error
Digital Feedthrough
Total Harmonic Distortion
Output Spot Noise Voltage
Symbol
Condition
5 V ± 10%
Unit
tS
To ±0.1% of full scale,
Data = 0x0000 to 0xFFFF to 0x0000 for AD5543
Data = 0x0000 to 0x3FFF to 0x0000 for AD5553
VREF = 100 mV rms, data = 0xFFFF
VREF = 0 V, data = 0x7FFF to 0x8000 for AD5543
Data = 0x0000, VREF = 100 mV rms, same channel
CS = 1 and fCLK = 1 MHz
VREF = 5 V p-p, data = 0xFFFF, f = 1 kHz
f = 1 kHz, BW = 1 Hz
0.5
µs typ
6.6
7
−83
7
−103
12
MHz typ
nV-sec
dB
nV-sec
dB typ
nV/√Hz
BW
Q
VOUT/VREF
Q
THD
eN
All static performance tests (except IOUT) are performed in a closed-loop system using an external precision OP177 I-to-V converter amplifier. The AD5543 RFB terminal is
tied to the amplifier output. The +IN op amp is grounded, and the DAC IOUT is tied to the −IN op amp. Typical values represent average readings measured at 25°C.
2
These parameters are guaranteed by design and are not subject to production testing.
3
All ac characteristic tests are performed in a closed-loop system using an AD8038 I-to-V converter amplifier except for THD where an AD8065 was used.
4
All input control signals are specified with tR = tF = 2.5 ns (10% to 90% of 3 V) and timed from a voltage level of 1.5 V.
1
TIMING DIAGRAMS
SDI
D15
D14
D13
D12
D11
D10
D9
D8
D1
D0
CLK
tDS
tDH
tCH
tCL
tCSS
tCSH
02917-016
CS
Figure 4. AD5543 Timing Diagram
SDI
D13
D12
D11
D10
D9
D8
D7
D6
D1
D0
CLK
tDS
tDH
tCH
tCL
tCSS
tCSH
02917-017
CS
Figure 5. AD5553 Timing Diagram
Rev. F | Page 4 of 20
Data Sheet
AD5543/AD5553
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter
VDD to GND
VREF to GND
Logic Inputs to GND
V(IOUT) to GND
Input Current to Any Pin Except Supplies
Package Power Dissipation
Thermal Resistance, θJA
8-Lead Surface Mount (MSOP)
8-Lead Surface Mount (SOIC)
Maximum Junction Temperature (TJ Max)
Operating Temperature Range
Model B and Model C
Storage Temperature Range
Lead Temperature
R-8, RM-8 (Vapor Phase, 60 sec)
R-8, RM-8 (Infrared, 15 sec)
Rating
−0.3 V to +8 V
−18 V to +18 V
−0.3 V to +8 V
−0.3 V to VDD + 0.3 V
±50 mA
(TJ Max − TA )/θJA
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
150°C/W
100°C/W
150°C
−40°C to +85°C
−65°C to +150°C
215°C
220°C
Rev. F | Page 5 of 20
AD5543/AD5553
Data Sheet
CLK 1
AD5543/
AD5553
SDI 2
RFB 3
VREF 4
TOP VIEW
(Not to Scale)
8
CS
7
VDD
6
GND
5
IOUT
02917-004
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Figure 6. Pin Configuration
Table 3. Pin Function Descriptions
Pin No.
1
2
3
4
5
Mnemonic
CLK
SDI
RFB
VREF
IOUT
6
7
8
GND
VDD
CS
Description
Clock Input. Positive-edge triggered, clocks data into shift register.
Serial Register Input. Data loads directly into the shift register MSB first. Extra leading bits are ignored.
Internal Matching Feedback Resistor. This pin connects to an external op amp for voltage output.
DAC Reference Input Pin. Establishes DAC full-scale voltage. Constant input resistance vs. code.
DAC Current Output. This pin connects to the inverting terminal of the external precision I-to-V op amp for
voltage output.
Analog and Digital Ground.
Positive Power Supply Input. Specified range of operation at 5 V ± 10%.
Chip Select. Active low digital input. Transfers shift-register data to DAC register on rising edge.
See Table 4 for operation.
Table 4. Control-Logic Truth Table
CLK
X
↑+ 1
X1
X1
1
CS
H
L
H
↑+1
Serial Shift Register Function
No effect
Shift register data advanced one bit
No effect
Shift register data transferred to DAC register
↑+ = positive logic transition; X = don't care.
Rev. F | Page 6 of 20
DAC Register
Latched
Latched
Latched
New data loaded from serial register
Data Sheet
AD5543/AD5553
1.0
0.8
0.8
0.6
0.6
0.4
0.4
0.2
0.2
DNL (LSB)
1.0
0
–0.2
0
–0.4
–0.4
–0.6
–0.6
–0.8
–0.8
–1.0
0
8192
16,384 24,576 32,768 40,960 49,152 57,344 65,536
CODE (Decimal)
–1.0
0
2048
Figure 7. AD5543 Integral Nonlinearity Error
4096
6144
8192 10,240 12,288 14,336 16,384
CODE (Decimal)
02917-008
–0.2
02917-005
INL (LSB)
TYPICAL PERFORMANCE CHARACTERISTICS
Figure 10. AD5553 Differential Nonlinearity Error
1.5
1.0
VREF = 2.5V
TA = 25°C
0.8
1.0
0.2
0
–0.2
–0.4
–0.6
0.5
INL
0
DNL
–0.5
–1.0
GE
–0.8
0
8192
16,384 24,576 32,768 40,960 49,152 57,344 65,536
CODE (Decimal)
–1.5
02917-006
–1.0
2
4
Figure 8. AD5543 Differential Nonlinearity Error
10
Figure 11. Linearity Error vs. VDD
5
1.0
VDD = 5V
TA = 25°C
0.8
4
SUPPLY CURRENT IDD (mA)
0.6
0.4
0.2
0
–0.2
–0.4
3
2
1
–0.6
–0.8
–1.0
0
2048
4096
6144
8192 10,240 12,288 14,336 16,384
CODE (Decimal)
02917-007
INL (LSB)
6
8
SUPPLY VOLTAGE VDD (V)
0
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
LOGIC INPUT VOLTAGE VIH (V)
Figure 12. Supply Current vs. Logic Input Voltage
Figure 9. AD5553 Integral Nonlinearity Error
Rev. F | Page 7 of 20
5.0
02917-010
DNL (LSB)
0.4
02917-009
LINEARITY ERROR (LSB)
0.6
AD5543/AD5553
Data Sheet
3.0
SUPPLY CURRENT (mA)
2.5
A2
–5V
5V
2V
DLY
67.72µs
2.0
0x5555
1.5
0x8000
1.0
0xFFFF
0x0000
100k
100M
1M
10M
CLOCK FREQUENCY (Hz)
136ns
Figure 16. Settling Time
Figure 13. AD5543 Supply Current vs. Clock Frequency
–3.65
90
VDD = 5V ± 10%
VREF = 10V
80
–3.70
70
–3.75
60
–3.80
VOUT (V)
PSRR (dB)
02917-014
0
10k
02917-011
0.5
50
40
–3.85
–3.90
30
–3.95
20
100
10k
1k
FREQUENCY (Hz)
100k
1M
–4.05
–20
02917-012
0
10
0
–40
–60
–80
–100
–120
–140
10
15
20
FREQUENCY (kHz)
25
02917-200
POWER SPECTRUM (dB)
–20
5
10
20
30
Figure 17. Midscale Transition and Digital Feedthrough
20
0
0
TIME (ns)
Figure 14. Power Supply Rejection Ratio (PSRR) vs. Frequency
–160
–10
Figure 15. AD5543/AD5553 Analog THD
Rev. F | Page 8 of 20
40
02917-026
–4.00
10
Data Sheet
AD5543/AD5553
CIRCUIT OPERATION
Note that a matching switch is used in series with the internal
5 kΩ feedback resistor. If users attempt to measure RFB, power
must be applied to VDD to achieve continuity.
DAC SECTION
VDD
The DAC architecture uses a current steering R-2R ladder
design. Figure 18 shows the typical equivalent DAC structure.
The DAC contains a matching feedback resistor for use with an
external op amp (see Figure 19). With RFB and IOUT terminals
connected to the op amp output and inverting node, respectively,
a precision voltage output is achieved as
VOUT = −VREF × D/65,536 (AD5543)
(1)
VOUT = −VREF × D/16,384 (AD5553)
(2)
Note that the output voltage polarity is the opposite of the VREF
polarity for dc reference voltages.
These DACs are designed to operate with either negative or
positive reference voltages. The VDD power pin is only used
by the internal logic to drive the on and off states of the DAC
switches.
VDD
R
R
R
RFB
VREF
2R
2R
2R
R
S2
5kΩ
S1
IOUT
DIGITAL INTERFACE CONNECTIONS OMITTED FOR CLARITY;
SWITCHES S1 AND S2 ARE CLOSED, VDD MUST BE POWERED.
02917-018
GND
R2
VREF
VREF
R1
C1
RFB
VDD
AD5543/
AD5553
IOUT1
A1
GND
VOUT = 0 TO –VREF
SYNC SCLK SDIN
AGND
µCONTROLLER
NOTES
1. R1 AND R2 USED ONLY IF GAIN ADJUSTMENT IS REQUIRED.
2. C1 PHASE COMPENSATION (4pF TO 6pF) MAY BE REQUIRED
IF A1 IS A HIGH SPEED AMPLIFIER.
02917-019
The AD5543/AD5553 contain 16-/14-bit current output, DACs,
serial input registers, and DAC registers. Both converters use a
3-wire serial data interface.
Figure 19. Voltage Output Configuration
These DACs are also designed to accommodate ac reference
input signals. The AD5543 accommodates input reference
voltages in the range of −12 V to +12 V. The reference voltage
inputs exhibit a constant nominal input resistance value of 5 kΩ
± 30%. The DAC output (IOUT) is code dependent, producing
various resistances and capacitances. External amplifier choice
should take into account the variation in impedance generated
by the AD5543 on the inverting input node of the amplifier.
The feedback resistance, in parallel with the DAC ladder
resistance, dominates output voltage noise. To maintain good
analog performance, power supply bypassing of 0.01 µF to 0.1 µF
ceramic or chip capacitors, in parallel with a 1 µF tantalum
capacitor, is recommended. Due to degradation of PSRR in
frequency, users must avoid using switching power supplies.
Figure 18. Equivalent R-2R DAC Circuit
Rev. F | Page 9 of 20
AD5543/AD5553
Data Sheet
SERIAL DATA INTERFACE
VDD
The AD5543/AD5553 use a 3-wire (CS, SDI, CLK) serial data
interface. New serial data is clocked into the serial input register
in a 16-bit data-word format for the AD5543. The MSB is loaded
first. Table 5 defines the 16 data-word bits. Data is placed on the
SDI pin and clocked into the register on the positive clock edge
of CLK, subject to the data setup-and-hold time requirements
that are specified in the interface timing specifications. Only the
last 16 bits clocked into the serial register are interrogated when
the CS pin is strobed to transfer the serial register data to the DAC
register. Because most microcontrollers output serial data in 8bit bytes, two data bytes can be written to the AD5543/AD5553.
After loading the serial register, the rising edge of CS transfers
the serial register data to the DAC register; during this strobe,
the CLK should not be toggled. For the AD5553, with 16-bit
clock cycles, the two LSBs are ignored.
DIGITAL
INPUTS
02917-020
5kΩ
DGND
Figure 20. Equivalent ESD Protection Circuits
PCB LAYOUT AND POWER SUPPLY BYPASSING
It is a good practice to employ compact, minimum lead length
PCB layout design. The leads to the input should be as short as
possible to minimize IR drop and stray inductance.
It is also essential to bypass the power supplies with quality
capacitors for optimum stability. Supply leads to the device
should be bypassed with 0.01 μF to 0.1 μF disc or chip ceramic
capacitors. Low ESR 1 μF to 10 μF tantalum or electrolytic
capacitors should also be applied at the supplies to minimize
transient disturbance and filter out low frequency ripple.
ESD PROTECTION CIRCUITS
All logic input pins contain back-biased ESD protection Zener
diodes that are connected to ground (DGND) and VDD, as
shown in Figure 20.
The PCB metal traces between VREF and RFB should also be
matched to minimize gain error.
Table 5. AD5543 Serial Input Register Data Format; Data Loaded MSB-First Format
B15 (MSB)
D15
B14
D14
B13
D13
B12
D12
B11
D11
B10
D10
B9
D9
B8
D8
B7
D7
B6
D6
B5
D5
B4
D4
B3
D3
B2
D2
B1
D1
B0 (LSB)
D0
Table 6. AD5553 Serial Input Register Data Format; Data Loaded MSB-First Format
B13 (MSB)1
D13
1
B12
D12
B11
D11
B10
D10
B9
D9
B8
D8
B7
D7
B6
D6
B5
D5
B4
D4
B3
D3
B2
D2
B1
D1
B0 (LSB)
D0
A full 16-bit data-word can be loaded into the AD5553 serial input register, but only the last 14 bits entered are transferred to the DAC register when CS returns to
logic high.
Rev. F | Page 10 of 20
Data Sheet
AD5543/AD5553
APPLICATIONS INFORMATION
STABILITY
BIPOLAR OUTPUT
VDD
RFB
VDD
IOUT
VREF
VO
AD8628
GND
AD5543/AD5553
02917-021
VREF
The AD5543/AD5553 are inherently 2-quadrant multiplying
DACs. That is, they can easily be set up for unipolar output
operation. The full-scale output polarity is the inverse of the
reference input voltage.
C1
U2
Figure 21. Optional Compensation Capacitor for Gain Peaking Prevention
In the I-to-V configuration, the IOUT of the DAC and the inverting
node of the op amp must be connected as close as possible to
each other, and proper PCB layout technique must be employed.
Because every code change corresponds to a step function, gain
peaking may occur if the op amp has limited GBP and there is
excessive parasitic capacitance at the inverting node.
An optional compensation capacitor, C1, can be added for
stability, as shown in Figure 21. C1 should be found empirically,
but 20 pF is generally adequate for the compensation.
POSITIVE VOLTAGE OUTPUT
To achieve the positive voltage output, an applied negative
reference to the input of the DAC is preferred over the output
inversion through an inverting amplifier because of the tolerance
errors of the resistors. To generate a negative reference, the
reference can be level-shifted by an op amp such that the VOUT
and GND pins of the reference become the virtual ground and
−2.5 V, respectively (see Figure 22).
In some applications, it may be necessary to generate the full
4-quadrant multiplying capability or a bipolar output swing,
which is easily accomplished by using an additional U4 external
amplifier configured as a summing amplifier (see Figure 23). In
this circuit, the second amplifier, U4, provides a gain of 2 that
increases the output span magnitude to 5 V. Biasing the external
amplifier with a 2.5 V offset from the reference voltage results in a
full 4-quadrant multiplying circuit. The transfer equation of this
circuit shows that both negative and positive output voltages are
created as the input data (D) is incremented from code zero
(VOUT = −2.5 V) to midscale (VOUT = 0 V) to full-scale (VOUT =
+2.5 V).
VOUT = (D/32,768 − 1) × VREF (AD5543)
(3)
VOUT = (D/16,384 − 1) × VREF (AD5553)
(4)
For the AD5543, the resistance tolerance becomes the dominant
error of which users should be aware.
R1
C2
U4 +5V
+5V
ADR03
+5V
ADR03
+5V
VOUT VIN
+5V
V+
1/2AD8620
V–
VDD
U3
U1
VDD
VOUT VIN
VREF
GND
GND
5kΩ ± 0.01%
R3
RFB
C1
VREF
AD5553 ONLY
C1
RFB
IOUT
1/2AD8620
1/2AD8628
GND
–5V
AD5543/AD5553
U2
0V < VO < +2.5V
Figure 22. Positive Voltage Output Configuration
Rev. F | Page 11 of 20
VO
–5V
–2.5V < VO < +2.5V
U2
Figure 23. 4-Quadrant Multiplying Application Circuit
VO
–2.5V
V+
1/2AD8620
V–
IOUT
U3
U1
GND
02917-022
U4
R2
10kΩ ± 0.01% 10kΩ ± 0.01%
02917-023
U1
AD5543/AD5553
Data Sheet
PROGRAMMABLE CURRENT SOURCE
REFERENCE SELECTION
Figure 24 shows a versatile V-I conversion circuit using an
improved Howland current pump. In addition to the precision
current conversion it provides, this circuit enables a bidirectional
current flow and high voltage compliance. This circuit can be used
in 4 mA to 20 mA current transmitters with up to 500 Ω of load. In
Figure 24, it can be shown that if the resistor network is matched,
the load current is
When selecting a reference for use with the AD55xx series of
current output DACs, pay attention to the output voltage,
temperature coefficient specification of the reference. Choosing
a precision reference with a low output temperature coefficient
minimizes error sources. Table 7 lists some of the references
available from Analog Devices, Inc., that are suitable for use
with this range of current output DACs.
IL =
(R2 + R3)/ R1
R3
× V REF × D
(5)
R3 in theory can be made small to achieve the current needed
within the U3 output current driving capability. This circuit is
versatile such that AD8510 can deliver ±20 mA in both directions
and the voltage compliance approaches 15 V, which is limited
mainly by the supply voltages of U3. However, users must pay
attention to the compensation. Without C1, it can be shown
that the output impedance becomes
ZO =
R1' R3(R1 + R2 )
(6)
R1(R2' + R3' ) − R1' (R2 + R3 )
If the resistors are perfectly matched, ZO is infinite, which is
desirable, and behaves as an ideal current source. On the other
hand, if they are not matched, ZO can be either positive or negative.
Negative can cause oscillation. As a result, C1 is needed to prevent
the oscillation. For critical applications, C1 could be found
empirically but typically falls in the range of a few picofarads (pF).
VDD
U1
VDD
VREF
VREF
GND
AD8628
R1'
R2'
150kΩ 15kΩ
C1
10pF
AD5543/AD5553
U2
VDD
V+
U3
R3'
50Ω
The input bias current of an op amp also generates an offset at
the voltage output because of the bias current flowing in the
feedback resistor, RFB.
Common-mode rejection of the op amp is important in voltageswitching circuits because it produces a code-dependent error
at the voltage output of the circuit.
Analog Devices offers a wide range of amplifiers for both
precision dc and ac applications, as listed in Table 8 and Table 9.
AD8510
V–
The primary requirement for the current-steering mode is an
amplifier with low input bias currents and low input offset
voltage. Because of the code-dependent output resistance of the
DAC, the input offset voltage of an op amp is multiplied by the
variable gain of the circuit. A change in this noise gain between
two adjacent digital fractions produces a step change in the
output voltage due to the amplifier’s input offset voltage. This
output voltage change is superimposed upon the desired change
in output between the two codes and gives rise to a differential
linearity error, which, if large enough, can cause the DAC to be
nonmonotonic.
Provided that the DAC switches are driven from true wideband
low impedance sources (VIN and AGND), they settle quickly.
Consequently, the slew rate and settling time of a voltageswitching DAC circuit is determined largely by the output op
amp. To obtain minimum settling time in this configuration,
minimize capacitance at the VREF node (the voltage output node
in this application) of the DAC. This is done by using low input
capacitance buffer amplifiers and careful board design.
RFB
IOUT
AMPLIFIER SELECTION
R3
50Ω
VSS
VL
R1
150kΩ
R2
15kΩ
IL
02917-024
LOAD
Figure 24. Programmable Current Source with Bidirectional Current Control
and High Voltage Compliance Capabilities
Rev. F | Page 12 of 20
Data Sheet
AD5543/AD5553
Table 7. Suitable Analog Devices Precision References
Part No.
ADR01
ADR01
ADR02
ADR02
ADR03
ADR03
ADR06
ADR06
ADR420
ADR421
ADR423
ADR425
ADR431
ADR435
ADR391
ADR395
Output Voltage (V)
10
10
5.0
5.0
2.5
2.5
3.0
3.0
2.048
2.50
3.00
5.00
2.500
5.000
2.5
5.0
Maximum Temperature
Drift (ppm/°C)
3
9
3
9
3
9
3
9
3
3
3
3
3
3
9
9
Initial Tolerance (%)
0.05
0.05
0.06
0.06
0.1
0.1
0.1
0.1
0.05
0.04
0.04
0.04
0.04
0.04
0.16
0.10
ISS (mA)
1
1
1
1
1
1
1
1
0.5
0.5
0.5
0.5
0.8
0.8
0.12
0.12
Output Noise (μV p-p)
20
20
10
10
6
6
10
10
1.75
1.75
2
3.4
3.5
8
5
8
Package(s)
SOIC-8
TSOT-5, SC70-5
SOIC-8
TSOT-5, SC70-5
SOIC-8
TSOT-5, SC70-5
SOIC-8
TSOT-5, SC70-5
SOIC-8, MSOP-8
SOIC-8, MSOP-8
SOIC-8, MSOP-8
SOIC-8, MSOP-8
SOIC-8, MSOP-8
SOIC-8, MSOP-8
TSOT-5
TSOT-5
Table 8. Suitable Analog Devices Precision Op Amps
Part No.
OP97
OP1177
AD8675
AD8671
ADA4004-1
AD8603
AD8607
AD8605
AD8615
AD8616
Supply Voltage (V)
±2 to ±20
±2.5 to ±15
±5 to ±18
±5 to ±15
±5 to ±15
1.8 to 5
1.8 to 5
2.7 to 5
2.7 to 5
2.7 to 5
VOS Maximum
(μV)
25
60
75
75
125
50
50
65
65
65
IB Maximum
(nA)
0.1
2
2
12
90
0.001
0.001
0.001
0.001
0.001
0.1 Hz to 10 Hz
Noise (μV p-p)
0.5
0.4
0.1
0.077
0.1
2.3
2.3
2.3
2.4
2.4
Supply Current (μA)
600
500
2300
3000
2000
40
40
1000
2000
2000
Package(s)
SOIC-8 , PDIP-8
MSOP-8, SOIC-8
MSOP-8, SOIC-8
MSOP-8, SOIC-8
SOIC-8, SOT-23-5
TSOT-5
MSOP-8, SOIC-8
WLCSP-5, SOT-23-5
TSOT-5
MSOP-8, SOIC-8
Table 9. Suitable Analog Devices High Speed Op Amps
Part No.
AD8065
AD8066
AD8021
AD8038
ADA4899-1
AD8057
AD8058
AD8061
AD8062
AD9631
Supply Voltage (V)
5 to 24
5 to 24
5 to 24
3 to 12
5 to 12
3 to 12
3 to 12
2.7 to 8
2.7 to 8
±3 to ±6
BW @ ACL (MHz)
145
145
490
350
600
325
325
320
320
320
Slew Rate (V/μs)
180
180
120
425
310
1000
850
650
650
1300
Rev. F | Page 13 of 20
VOS (Max) (μV)
1500
1500
1000
3000
35
5000
5000
6000
6000
10,000
IB (Max) (nA)
0.006
0.006
10,500
750
100
500
500
350
350
7000
Package(s)
SOIC-8, SOT-23-5
SOIC-8, MSOP-8
SOIC-8, MSOP-8
SOIC-8, SC70-5
LFCSP-8, SOIC-8
SOT-23-5, SOIC-8
SOIC-8, MSOP-8
SOT-23-5, SOIC-8
SOIC-8, MSOP-8
SOIC-8, PDIP-8
AD5543/AD5553
Data Sheet
EVALUATION BOARD
SPORT_TFS
CS
SPORT_TSCLK
SCLK
SPORT_DTO
SDIN
SYSTEM DEVELOPMENT PLATFORM
02917-124
The EVAL-AD5543/EVAL-AD5553 is used in conjunction with
an SDP1Z system development platform board available from
Analog Devices, which is purchased separately from the
evaluation board. The USB-to-SPI communication to the
AD5543 is completed using this Blackfin-based development
board. The software offers a waveform generator.
The system development platform (SDP) is a hardware and
software evaluation tool for use in conjunction with product
evaluation boards. The SDP board is based on the Blackfin
BF527 processor with USB connectivity to the PC through a
USB 2.0 high speed port. For more information about this
device, see the system development platform web page.
WAVEFORM GENERATOR
AD5543/AD5553 TO SPORT INTERFACE
OPERATING THE EVALUATION BOARD
The Analog Devices SDP has one SPORT serial port. The
SPORT interface is used to control the AD5543/AD5553,
allowing clock frequencies up to 30 MHz.
The evaluation board requires ±12 V and +5 V supplies. The
+12 V VDD and VSS are used to power the output amplifier, while
the +5 V is used to power the DAC (VDD1).
AD5543/AD5553
ADSP-BF527
Figure 25. AD5543/AD5553 to SPORT Interface
02917-125
The evaluation board software offers a waveform generator to
show every change introduced and transmitted to the output.
Figure 26. Evaluation Board Software—Waveform Generator
Rev. F | Page 14 of 20
Rev. F | Page 15 of 20
Figure 27. Schematic of AD5543/AD5553 Evaluation Board
C8
10uF
+
4
U2
ADR435
C9 5 TRIM
0.1uF
GND
VOUT
8
/CS
2
2
/CS
SDIN
+ VIN
SDIN
J1-3
J1-4
J1-5
1
SCLK
DGND
SCLK
VDD
VSS
VDD
J1-2
6
CS
C1
AGND
0.1uF
C10
AGND
6
LK1
VREF
IOUT
RFB
C2
AD5543_53
SDIN
SCLK
U1
7
VDD
DVDD
4
5
3
0.1uF
10uF
OP AMP + REFERENCE SUPPLY
DAC + VIN FOR SDP
+
J1-1
J3
U3
+ DIS
8
-
VDD
3
2
VREF
C3
5.6pF
VSS
C6
V- 4
OP
V+ 7
C5
C4
C7
+
10uF
6
0.1uF
10uF
0.1uF
+
DVDD
VOUT
J4
VOUT
Data Sheet
AD5543/AD5553
02917-126
AD5543/AD5553
Data Sheet
BMODE1: PULL UP WITH A 10k RESISTOR TO SET SDP TO BOOT FROM A SPI FLASH ON THE DAUGHTER BOARD
J2
VIN: USE THIS PIN TO POWER THE SDP
REQUIRES 4-7V 200mA
RESET_IN
BMODE1
UART_TX
UART_RX
GND
GND
NC
NC
SDP
NC
NC
STANDARD
NC
NC
CONNECTOR
NC
NC
NC
NC
GND
GND
NC
NC
NC
NC
TMR_D
TMR_C *
TIMERS
TMR_B
TMR_A
GPIO7
GPIO6
GND
GND
GENERAL
GPIO5
GPIO4
INPUT/OUTPUT
GPIO3
GPIO2
GPIO1
GPIO0
SCL_0
SCL_1
I2C
SDA_0
SDA_1
GND
GND
SPI_CLK
SPI_SEL1/SPI_SS
SPI_MISO
SPI_SEL_C
SPI
SPI_MOSI
SPI_SEL_B
SPI_SEL_A
GND
GND
SPORT_INT
SPORT_TSCLK
SPORT_DT3 *
*
SPORT_DT0
SPORT_DT2
SPORT
SPORT_TFS
SPORT_DT1
SPORT_RFS
SPORT_DR1
SPORT_DR0
SPORT_DR2 *
SPORT_RSCLK
SPORT_DR3 *
GND
GND
PAR_CLK
PAR_FS1
PAR_FS2
PAR_FS3
PAR_A0
PAR_A1
PAR_A2
PAR_A3
GND
GND
PAR_INT
PAR_CS
PAR_WR
PAR_RD
PAR_D0
PAR_D1
PARALLEL
PAR_D2
PAR_D3
PORT
PAR_D4
PAR_D5
GND
GND
PAR_D6
PAR_D7
PAR_D8
PAR_D9
PAR_D10
PAR_D11
PAR_D12
PAR_D13
GND
PAR_D14
PAR_D15
GND
*
*
PAR_D16
PAR_D17
* PAR_D18
PAR_D19 *
* PAR_D20
PAR_D21 *
* PAR_D22
PAR_D23 *
GND
GND
VIO(+3.3V)
USB_VBUS
GND
GND
GND
GND
NC
NC
*NC ON BLACKFIN SDP
NC
VIN
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
BOARD ID EEPROM (24LC64) MUST BE ON I2C BUS 0, ADDRESS IS AT USER DISCRETION
3.3V_BF
U4
1
2 A0
3 A1
4 A2
VSS
24LC64
STATUS
START
MAIN I2C BUS (CONNECTED TO BLACKFIN TWI - PULL UP RESISTORS NOT REQUIRED)
I2C BUS 1 IS COMMON ACROSS BOTH CONNECTORS ON SDP - PULL UP RESISTORS REQUIRED
(CONNECTED TO BLACKFIN GPIO - USE I2C_0 FIRST)
Figure 28. Schematic of SDP Interface
Rev. F | Page 16 of 20
8
VCC 7
WP 6
SCL 5
SDA
SCLK
SDIN
/CS
3.3V_BF
VIO: USE TO SET IO VOLTAGE MAX DRAW 20mA
02917-127
USB_VBUS
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
AD5543/AD5553
02917-128
Data Sheet
02917-129
Figure 29. Silkscreen—Component Side View (Top Layer)
02917-130
Figure 30 Component Side Artwork
Figure 31. Solder Side Artwork
Rev. F | Page 17 of 20
AD5543/AD5553
Data Sheet
BILL OF MATERIALS
Table 10.
Name
CS
AGND
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C12
GL1
J1
J2
J3
J4
SCLK
SDIN
U1
U2
U3
U4
USB_VBUS
VOUT
VREF
X1
X2
Part Description
Testpoint
Testpoint
Capacitor+
Capacitor
Capacitor
Capacitor+
Capacitor
Capacitor+
Capacitor
Capacitor+
Capacitor
Capacitor
Capacitor
Capacitor
Ground link
CON\POWER5
SDP-STANDARD-CONN
SMB
SMB
Testpoint
Testpoint
AD5543/AD5553
ADR435
AD8038
24LC64
Testpoint
Testpoint
Testpoint
MTHOLE-3MM
MTHOLE-3MM
Value
10 µF
0.1 µF
5.6 pF
10 µF
0.1 µF
10 µF
0.1 µF
10 µF
0.1 µF
0.1 µF
10 µF
0.1 µF
PCB Decal
Testpoint
Testpoint
RTAJ_A
C0603
C0603
RTAJ_B
C0603
RTAJ_B
C0603
RTAJ_B
C0603
C0603
C0805
C0603
Component link
CON\POWER5
CON-120/FX8-120S-SV
SMB
SMB
Testpoint
Testpoint
SO8NB
SO8NB
SO8NB
MSO8
Testpoint
Testpoint
Testpoint
MTHOLE-3MM
MTHOLE-3MM
Rev. F | Page 18 of 20
Part Description
Red testpoint
Black testpoint
10 V SMD tantalum capacitor
50 V X7R ceramic capacitor
Multilayer ceramic capacitor
16 V tantalum capacitor
50 V X7R ceramic capacitor
16 V tantalum capacitor
50 V X7R ceramic capacitor
16 V tantalum capacitor
50 V X7R ceramic capacitor
50 V X7R ceramic capacitor
10 V 10 µF ceramic capacitor 10% X5R 0805
50 V X7R ceramic capacitor
Copper short
5-pin terminal block
120-way connector, 0.6 mm pitch, receptacle
Straight PCB mount SMB jack—50 Ω
Straight PCB mount SMB jack—50 Ω
Red testpoint
Red testpoint
Digital-to-analog converter
5 V reference
Single op amp 8-pin
64K I2C serial EEPROM MSOP8
Black testpoint
Red testpoint
Red testpoint
3 mm NPTH hole
3 mm NPTH hole
Data Sheet
AD5543/AD5553
OUTLINE DIMENSIONS
3.20
3.00
2.80
8
3.20
3.00
2.80
5.15
4.90
4.65
5
1
4
PIN 1
IDENTIFIER
0.65 BSC
0.95
0.85
0.75
15° MAX
1.10 MAX
0.80
0.55
0.40
0.23
0.09
6°
0°
0.40
0.25
10-07-2009-B
0.15
0.05
COPLANARITY
0.10
COMPLIANT TO JEDEC STANDARDS MO-187-AA
Figure 32. 8-Lead Mini Small Outline Package [MSOP]
(RM-8)
Dimensions shown in millimeters
5.00 (0.1968)
4.80 (0.1890)
1
5
6.20 (0.2441)
5.80 (0.2284)
4
1.27 (0.0500)
BSC
0.25 (0.0098)
0.10 (0.0040)
COPLANARITY
0.10
SEATING
PLANE
1.75 (0.0688)
1.35 (0.0532)
0.51 (0.0201)
0.31 (0.0122)
0.50 (0.0196)
0.25 (0.0099)
45°
8°
0°
0.25 (0.0098)
0.17 (0.0067)
1.27 (0.0500)
0.40 (0.0157)
COMPLIANT TO JEDEC STANDARDS MS-012-AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 33. 8-Lead Standard Small Outline Package [SOIC_N]
Narrow Body
(R-8)
Dimensions shown in millimeters and (inches)
Rev. F | Page 19 of 20
012407-A
8
4.00 (0.1574)
3.80 (0.1497)
AD5543/AD5553
Data Sheet
ORDERING GUIDE
Model 1, 2
AD5543CRMZ
AD5543CRMZ-REEL7
AD5543BR
AD5543BRZ
AD5543BRM
AD5543BRM-REEL7
AD5543BRMZ
AD5543BRMZ-REEL7
AD5553CRM
AD5553CRM-REEL7
AD5553CRMZ
AD5553CRMZ-REEL7
EVAL-AD5543SDZ
1
2
INL (LSB)
±1
±1
±2
±2
±2
±2
±2
±2
±1
±1
±1
±1
RES (LSB)
16
16
16
16
16
16
16
16
14
14
14
14
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
The AD5543 contains 1040 transistors. The die size measures 55 mil × 73 mil or 4,015 sq. mil.
Z = RoHS Compliant Part, # denotes RoHS-compliant product may be top or bottom marked.
©2002–2012 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D02917-0-1/12(F)
Rev. F | Page 20 of 20
Package Description
8-Lead MSOP
8-Lead MSOP
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead MSOP
8-Lead MSOP
8-Lead MSOP
8-Lead MSOP
8-Lead MSOP
8-Lead MSOP
8-Lead MSOP
8-Lead MSOP
Evaluation Board
Package Option
RM-8
RM-8
R-8
R-8
RM-8
RM-8
RM-8
RM-8
RM-8
RM-8
RM-8
RM-8
Branding
DEV
DEV
DXB
DXB
DXB#
DXB#
DUC
DUC
DUC#
DUC#
Similar pages