7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER 5 4 3 2 20 REVISION 2151011 -1 DESCRIPTION F 2151011 -2 FINE CRIMP HEIGHT ADJUST F 2151011 -5 SERVO LATCH PLATE SMART APPLICATOR MECHANICAL FEED PNEUMATIC SERVO LATCH PLATE SMART APPLICATOR MECHANICAL FEED FINE CRIMP HEIGHT ADJUST SERVO LATCH PLATE 12 F NON-CRIMP HEIGHT ADJUST 2151011 -7 F FINE CRIMP HEIGHT ADJUST A PNEUMATIC FEED SERVO LATCH PLATE 2151011 -6 7- 2151011 -7 CONVERT TO MECHANICAL FINE CRIMP HEIGHT ADJUST F APPLICATOR STYLE CONVERSION CHART FEED TYPE 4 NONE CRIMP TOOLING KIT - 4 PNEUMATIC FEED - CRIMP WIRE INSUL SIZE 2119950-1 1338685-1 2161326-1 - 2119951-1 - 2119949-1 - - - 5-18022-5 1338685-1 - - - 8- 2151011 -4 1338685-1 2119950-1 8- 2151011 -4 8- 2151011 -5 - 2119949-1 2119799-1 5-18022-5 - 2161326-1 2119641-1 8- 2151011 -5 1338685-1 2119951-1 5-18022-5 5-18022-5 - - - - - 2119653-1 1901094-3 - 2119653-1 2119641-1 - - - 2168400-6 2168400-6 - 2119799-1 - (QUANTITY 2) - - - (QUANTITY 2) - - - - - 2063440-1 - - - - - - - - - - - - - - 1901094-3 - - 6 - TYPE 1.78 mm [.070] APPLICATOR INSTRUCTIONS 408-10389 - - - TE TERMINAL TERMINAL DATA: RECEPTACLE, CST-100 TERMINAL NAME: WIRE STRIP LENGTH 2.54-3.18 mm [.100-.125 IN] C TERMINAL APPLICATION SPECIFICATION n 114-13036 - - TE CRIMP SPECIFICATION - INSULATION DIAMETER RANGE - 0.89-1.65 mm [.035-.065 IN] - - - - - - 6 TERMINALS APPLIED TE TERMINAL 1375819-1 TE TERMINAL 1375819-2 C1__DWG_PN_1_0 C1__DWG_PN_1_1 C1__DWG_PN_2_0 C1__DWG_PN_2_1 TE TERMINAL 1375819-3 C1__DWG_PN_3_0 C1__DWG_PN_3_1 TE TERMINAL 647607-1 - C1__DWG_PN_4_0 - C1__DWG_PN_4_1 - WIRE SIZE 22 AWG 24 AWG 26 AWG B CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 0.86+/-0.05 [.034+/-.002] 0.81+/-0.05 [.032+/-.002] 0.76+/-0.05 [.030+/-.002] 1 RECOMMENDED SPARE PARTS 2 GREASE BEARING SURFACES LIGHTLY CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 - 9 8.4 8.9 9.4 - W1__FA_SETTING_1 - W1__FA_SETTING_2 - W1__FA_SETTING_3 - *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. 6 APPLICATOR SPECIFIC DATA TO BE ENTERED INTO BLANK MEMORY CHIP AT ASSEMBLY. SEE BELOW FOR PART NUMBER: MECHANICAL FEED WITH "SMART APPLICATOR" CONVERSION: 8PNEUMATIC FEED WITH "SMART APPLICATOR" CONVERSION: 8SERVO FEED WITH "FINE CRIMP HEIGHT ADJUST": 8SERVO FEED WITH "NON-CRIMP HEIGHT ADJUST": 8- 7 8 9 10 11 2151011 2151011 2151011 2151011 - -4 -4 -5 -6 - A 12 - APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEMS 62. APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEMS 242. FOR -6 ONLY APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 37. 1 GREASE THREADS, GROOVE AND O-RING ON ITEMS 35 & 252. 1 1 MAGNET, ITEM 166 MUST BE ORIENTED CORRECTLY IN ORDER TO PROPERLY ACTUATE THE COUNTER. 1 CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. WHEN ASSEMBLING -6 NON-CRIMP HEIGHT ADJUST APPLICATOR USE SHIM PACK 2119957-2 TO ALIGN APPLICATOR'S MAXIMUM WIRE CRIMP HEIGHT AT NORMAL TERMINATOR SHUT HEIGHT 1 - - 1 -77 -7 1 - -6 1 -5 1 -2 1 2119957-2 8-21084-0 -1 PART NO - APPLICATOR SHIM PACK O-RING, .676 ID, .070 DIA. MAT. DESCRIPTION 1 2119957-2 1 8-21084-0_GATD 260 252 1 1 1 1 ITEM NO - 1 1 1 1 1 1 1 REF 1 1 1 1 2 1 3 1 4 2 1 1 1 - - 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - - - 1 66 P LTR DESCRIPTION DATE ECR-16-002768 - - 1 - - mm MATERIAL - -1 PART NO - 2 1 1 - - - 1 - - 1 - 1 1 1 1 - - - 1 1 - - - 1 1 2 - 1 1 1 2 1 1 1 1 - 1 1 1 1 - 1 1 1 1 - 1 - 1 1 1 - 1 1 2119640-1 2079988-1 2119641-1 2119798-1 1-22279-3 2119758-1 2119082-9 2079764-1 2119083-1 7-18023-7 2168400-6 2119580-1 2063440-1 2119740-2 1901094-3 21045-3 994969-1 994970-2 240638-1 3-23627-7 2119799-1 SEE NOTE 4 1633743-1 1-18028-2 2119944-1 455888-5 2119956-1 2119740-1 2168078-1 2119793-1 992763-5 2079383-4 5-18022-5 1338685-1 2168400-1 2168083-3 5018030-1 811242-5 690753-2 18023-9 2119652-1 2119653-1 2119656-9 2119370-1 2079383-7 2119645-1 2119957-1 2119644-1 2119085-1 2119092-1 1752356-5 2079383-5 2161328-1 1320908-2 2119959-1 1-455888-0 1320928-2 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 462006-6 1338689-1 2119757-8 238011-7 2-2119582-0 455888-8 456401-7 - - 1 1 REF REF REF REF - - - 1 - - 1 - 1 1 1 1 1 1 -6 1 1 1 1 - 1 1 1 - - 1 1 1 - - 1 1 1 - 1 1 1 1 - 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 - 1 - 1 1 2 - - - 1 1 - 1 1 1 - - 1 1 1 - 2 1 1 - 4 2 1 1 1 4 2 1 1 1 4 1 1 1 - 2 3 1 - 4 1 3 1 - 2 1 3 - 1 2 1 1 1 1 2 - 1 1 - - - 1 1 2 1 - 1 - - 1 REF REF 1 - - 1 1 - - 1 1 - 1 REF REF 1 - 1 1 -5 -2 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: & 4 of 4) - -77 -7 ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 AMP 4805 REV 31MAR2000 - - SPARE FEED CAM STORAGE LOCATION REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. TO CONVERT THE APPLICATOR TO A NON-CARRIER CUTTING STYLE, REMOVE ITEM 13 AND ATTACH TO THE LOCATION ON THE BACK SIDE OF THE HOUSING. REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. - 5. ADJUSTMENT OF THE STRIPPER MAY BE REQUIRED WHEN MOVING THE APPLICATOR BETWEEN BENCH AND LEADMAKER APPLICATIONS. 6 - 3. LUBRICATE DAILY PER THE APPLICATOR INSTRUCTION SHEET SUPPLIED WITH THE APPLICATOR. 4 A DWN APVD XZ 24FEB2016 TE 2063440-1 F F 1.07 mm [.042] REVISIONS DIST F - APPLICATOR DATA 1 PART NUMBERS REQUIRED - - LOC SET UP GAUGE 2119599-1 ALL RIGHTS RESERVED. PART NUMBER D 6 TOLERANCES UNLESS OTHERWISE SPECIFIED: FINISH DWN 03NOV2011 CHK 04NOV2011 APVD 04NOV2011 HOFFNER T.ELBIN T.ELBIN - WEIGHT NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 1 2119641-1 1 2119798-1 1 1-22279-3_SIMP 1 2119758 1 2119082-9 1 2079764 1 2119083 1 7-18023-7 2 2168400-6 1 2119580-1 1 2063440-1 1 2119740-2 .. 1 1901094-3 2 21045-3 1 994969-1_GATD 1 COUNTER_994970 1 240638 1 3-23627-7 1 2119799 1 1901689_EMPTY_OCEAN_SF .. 1 1633743-1 1 1-18028-2 1 2119944-1 1 455888-5 1 2119956-1 1 2119740-1 2 2168078-1 1 2119793 3 992763-5 1 2079383-4 1 5-18022-5 1 1338685-1 4 2168400-1 2 2168083-3 1 5018030-1 1 811242-5_OLD 1 690753-2 3 18023-9 1 2119652 1 2119653 1 2119656-9 1 2119370 1 2079383-7 1 2119645 1 2119957-1 1 2119644-1 1 2119085 1 2119092-1 1 1752356-5 2 2079383-5 1 2161328 1 1320908-2 1 2119959-1 1 1-455888-0 1 1320928-2 1 2168083-2 1 1-18028-2 1 2119533-1 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 462006-6 1 1338689-1 .. 1 ITEM_7 .. 1 ITEM_6 1 2119757-8 1 238011-7 1 2-2119582-0 1 455888-8 1 456401-7 250 249 248 247 246 245 244 243 242 241 240 239 238 213 198 172 166 164 163 137 136 135 133 119 117 82 71 67 66 63 62 60 59 56 54 53 52 51 50 49 48 47 46 44 41 40 39 38 37 35 34 33 32 30 29 28 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 ITEM NO Harrisburg, PA 17105-3608 - 1 2079988_GATD TE Connectivity APPLICATION SPEC - 1 2119640-1 DESCRIPTION PRODUCT SPEC - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES PUSH ROD, AIR FEED BUSHING, LCH5-12, MISUMI FEED CAM, AIR FEED DETENT PIN SPRING, COMPRESSION RAM, AMP STYLE, SIDE FEED, NON-ADJ. CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 SHCS, LOW HEAD, RoHS, M5 X 16 MECHANICAL FEED ASSEMBLY AIR FEED MODULE TAG,IDENTIFICATION SPACER, FEEDER RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER PIN, RETAIN, GRVD, 3/16 X .854 HOLDER,FEED FINGER, AF MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM WASHER, FLAT, REG M4 FEED FINGER ASSEMBLY,SF SPACER, CRIMPER DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE POINT, M3 x 4.0 SCR, BHSC, RoHS (M4 X 8) SCR, HEX HD CAP, M4 X 6.0 PAWL, FEED SHCS, LOW HEAD, RoHS, M4 X 12 SCR, SKT HD CAP, RoHS, M4 X 12.0 NUT, HEX, REG, RoHS, M3 BUMPER, HOLD DOWN SPACER, TONKER SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM, AMP STYLE, SIDE FEED SCR, BHSC, RoHS (M8 X 25) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION FA HEAD, ATLANTIC STYLE BOLT, ADJUSTMENT SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) HEX HEAD, FLANGED, M5 x 8mm LONG SPACER, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION .042 DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION F PREMIUM SPACER, CRIMPER CRIMPER, WIRE .042 F PREMIUM Ocean Side Feed Applicator - DRAWING NO 2151011 SCALE 1:2 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV F D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR - FEED TYPE MECHANICAL A D 6 37 6 62 59 38 56 39 250 247 246 260 44 7 252 245 35 244 2 7 249 63 A 166 242 1 53 2 2 2 2 6 0.0 34 REF 2 3 52 C 1 51 56 REF 1 50 172 4 SERVO LATCH PLATE TERMINAL SUPPORT LOCATION 28 5 41 135 198 66 2 164 A 67 11 213 33 24 SERVO FEEDER NOT INCLUDED B - D 8 82 137 4 - - 2 163 136 133 APVD 8 59 240 SEE SHEET 1 DWN 243 238 C DATE 40 239 PNEUMATIC DESCRIPTION 10 A 19 30 117 REF B 20 9 21 29 1 12 ITEM 30 LOCATED AT FRONT HOLES 241 13 CAM POSITIONS 30mm STROKE 30mm STROKE 30mm STROKE 47 46 32 34 54 8 1 60 54 10 1 119 1 30 REF 29 REF 11 11 FEED TRACK POSITION GUIDE BY INSULATION BARREL 248 48 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 40mm STROKE MECHANICAL PRE FEED 49 40mm STROKE AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: FINISH 03NOV2011 CHK 04NOV2011 APVD 04NOV2011 HOFFNER T.ELBIN T.ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES DWN - APPLICATION SPEC - - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean Side Feed Applicator - DRAWING NO 2151011 SCALE 1:2 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV F 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 5 4 3 2 20 SET UP GAUGE 2119599-1 ALL RIGHTS RESERVED. PART NUMBER REVISION 2- 2151011 -1 DESCRIPTION F 2- 2151011 -2 D 6 FEED TYPE FINE CRIMP HEIGHT ADJUST F FINE CRIMP HEIGHT ADJUST F FINE CRIMP HEIGHT ADJUST 2- 2151011 -7 F FINE CRIMP HEIGHT ADJUST NONE CRIMP TOOLING KIT PNEUMATIC FEED SERVO LATCH PLATE SMART APPLICATOR MECHANICAL FEED PNEUMATIC 2- 2151011 -5 A CONVERT TO MECHANICAL SERVO LATCH PLATE 7- 2151011 -7 APPLICATOR STYLE CONVERSION CHART - SERVO LATCH PLATE SMART APPLICATOR MECHANICAL FEED 4 PNEUMATIC FEED - - CRIMP WIRE INSUL SIZE 2119950-1 1338685-1 2161326-1 - 2119951-1 2119949-1 2119951-1 2161326-1 2119949-1 2119950-1 - - 1338685-1 - - 1338685-1 1338685-1 - 5-18022-5 8- 2151011 -5 8- 2151011 -4 5-18022-5 8- 2151011 -5 8- 2151011 -4 5-18022-5 5-18022-5 - 2119641-2 2119799-1 - - 1901094-3 2119653-2 1901094-3 - 2119653-2 2119641-2 - - - 2168400-6 2168400-6 - 2119799-1 - (QUANTITY 2) - - - - - (QUANTITY 2) - - - - - 2063440-1 - 6 - - - - - - TYPE APPLICATOR INSTRUCTIONS 408-10389 - - - TE TERMINAL TERMINAL DATA: RECEPTACLE, CST-100 TERMINAL NAME: WIRE STRIP LENGTH 2.54-3.18 mm [.100-.125 IN] C TERMINAL APPLICATION SPECIFICATION n 114-13036 - - TE CRIMP SPECIFICATION - INSULATION DIAMETER RANGE - 0.89-1.65 mm [.035-.065 IN] - - - - - TERMINALS APPLIED TE TERMINAL 1375819-1 TE TERMINAL C1__DWG_PN_1_0 1375819-2 C1__DWG_PN_1_1 C1__DWG_PN_2_0 TE TERMINAL C1__DWG_PN_2_1 C1__DWG_PN_3_0 1375819-3 C1__DWG_PN_3_1 TE TERMINAL - C1__DWG_PN_4_0 647607-1 - C1__DWG_PN_4_1 - WIRE SIZE 22 AWG 24 AWG 26 AWG CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 0.86+/-0.05 [.034+/-.002] 0.81+/-0.05 [.032+/-.002] 0.76+/-0.05 [.030+/-.002] CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 8.4 8.9 9.4 - 9 - 6 - W1__FA_SETTING_1 - W1__FA_SETTING_2 - W1__FA_SETTING_3 - 1 B 2 - *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. RECOMMENDED SPARE PARTS - GREASE BEARING SURFACES LIGHTLY - 3. LUBRICATE DAILY PER THE APPLICATOR INSTRUCTION SHEET SUPPLIED WITH THE APPLICATOR. 4 APPLICATOR SPECIFIC DATA TO BE ENTERED INTO BLANK MEMORY CHIP AT ASSEMBLY. SEE BELOW FOR PART NUMBER: MECHANICAL FEED WITH "SMART APPLICATOR" CONVERSION: 8PNEUMATIC FEED WITH "SMART APPLICATOR" CONVERSION: 8SERVO FEED WITH "FINE CRIMP HEIGHT ADJUST": 8- - 2151011 -4 2151011 -4 2151011 -5 - 5. ADJUSTMENT OF THE STRIPPER MAY BE REQUIRED WHEN MOVING THE APPLICATOR BETWEEN BENCH AND LEADMAKER APPLICATIONS. 6 7 8 9 10 A 11 - 1 APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEMS 62. APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEMS 242. - 1 GREASE THREADS, GROOVE AND O-RING ON ITEMS 139 & 152. - 1 1 1 MAGNET MUST BE ORIENTED CORRECTLY IN ORDER TO PROPERLY ACTUATE THE COUNTER. - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. - - SPARE FEED CAM STORAGE LOCATION REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. TO CONVERT THE APPLICATOR TO A NON-CARRIER CUTTING STYLE, REMOVE ITEM 13 AND ATTACH TO THE LOCATION ON BACK SIDE OF THE HOUSING. REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. 1 1 1 1 - 1 1 - 1 P LTR DESCRIPTION DATE SEE SHEET 1 - - 1 - 1 1 - 2 1 REF - - - 1 - - 1 - 1 1 1 - - - - - 1 - - - 1 1 2 - 1 1 1 - 1 1 1 1 1 1 1 1 - 1 1 1 - 1 1 2119782-1 2119640-1 2079988-1 1-22279-3 2119082-9 2079764-1 2119083-1 7-18023-7 2168400-6 2119580-1 2063440-1 2119740-2 1901094-3 21045-3 994969-1 994970-2 240638-1 8-21084-1 2119641-2 2119798-2 2079383-8 2168400-5 2119653-2 1-2119656-0 2119650-1 2119092-2 3-23627-7 2119799-1 SEE NOTE 4 1633743-1 1-18028-2 2119944-1 455888-5 2119956-1 2119740-1 2168078-1 2119793-1 992763-5 5-18022-5 1338685-1 2168083-3 5018030-1 811242-5 690753-2 18023-9 2119652-1 2079383-7 2119645-1 2119957-1 2119644-1 1752356-5 2079383-5 2161328-1 1320908-2 2119959-1 1-455888-0 1320928-2 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 462006-6 1338689-1 2119757-8 238011-7 2-2119582-0 455888-8 456401-7 1 - 1 1 REF REF REF - - 1 1 1 - 1 - 1 1 1 1 1 1 1 1 1 - 1 1 1 - - 1 1 1 - - 1 1 1 - - 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 2 - 1 1 1 1 - 1 1 1 - - 1 1 1 - 2 1 1 1 1 2 1 1 1 1 2 1 3 1 - 2 1 3 - - 2 1 3 - 1 2 1 3 1 1 2 1 1 1 - 2 - 1 1 1 1 - 1 1 - 1 REF 1 - - 1 - - - 1 1 - 1 REF - 1 1 - - 1 1 - - 1 1 1 - 1 1 1 1 4 - 1 1 1 4 - 1 1 1 4 - - 1 1 4 1 1 1 1 - 1 1 1 1 1 1 DWN APVD - - THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - FINISH DWN 03NOV2011 CHK 04NOV2011 APVD 04NOV2011 HOFFNER T.ELBIN T.ELBIN - WEIGHT NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 1 2079988_GATD 1 1-22279-3_SIMP 1 2119082-9 1 2079764 1 2119083 1 7-18023-7 2 2168400-6 1 2119580-1 1 2063440-1 1 2119740-2 .. 1 1901094-3 2 21045-3 1 994969-1_GATD 1 COUNTER_994970 1 240638 1 8-21084-1_GATD 1 2119641-2 1 2119798-2 1 2079383-8 4 2168400-5 1 2119653-2 1 1-2119656-0 1 2119650 1 2119092-2 1 3-23627-7 1 2119799 1 1901689_EMPTY_OCEAN_SF .. 1 1633743-1 1 1-18028-2 1 2119944-1 1 455888-5 1 2119956-1 1 2119740-1 2 2168078-1 1 2119793 3 992763-5 1 5-18022-5 1 1338685-1 2 2168083-3 1 5018030-1 1 811242-5_OLD 1 690753-2 3 18023-9 1 2119652 1 2079383-7 1 2119645 1 2119957-1 1 2119644-1 1 1752356-5 2 2079383-5 1 2161328 1 1320908-2 1 2119959-1 1 1-455888-0 1 1320928-2 1 2168083-2 1 1-18028-2 1 2119533-1 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 462006-6 1 1338689-1 .. 1 ITEM_7 .. 1 ITEM_6 1 2119757-8 1 238011-7 1 2-2119582-0 1 455888-8 1 456401-7 251 250 249 246 244 243 242 241 240 239 238 213 198 172 166 164 163 152 151 145 144 143 142 141 140 139 137 136 135 133 119 117 82 71 67 66 63 62 59 56 53 52 51 50 49 48 41 40 39 38 34 33 32 30 29 28 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 ITEM NO Harrisburg, PA 17105-3608 - 1 2119640-1 TE Connectivity APPLICATION SPEC - 1 2119782 DESCRIPTION PRODUCT SPEC - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINE ADJUST HEAD ASM, PACIFIC STYLE PUSH ROD, AIR FEED BUSHING, LCH5-12, MISUMI SPRING, COMPRESSION CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 SHCS, LOW HEAD, RoHS, M5 X 16 MECHANICAL FEED ASSEMBLY AIR FEED MODULE TAG,IDENTIFICATION SPACER, FEEDER RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER O-RING, .801 ID, .070 DIA. MAT. FEED CAM, AIR FEED DETENT PIN SCR, BHSC, RoHS (M4 X 16) SHCS, LOW HEAD, RoHS, M4 X 20 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM, ASIAN STYLE, SIDE FEED BOLT, ADJUSTMENT PIN, RETAIN, GRVD, 3/16 X .854 HOLDER,FEED FINGER, AF MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM WASHER, FLAT, REG M4 FEED FINGER ASSEMBLY,SF SPACER, CRIMPER DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE POINT, M3 x 4.0 SCR, HEX HD CAP, M4 X 6.0 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 12.0 NUT, HEX, REG, RoHS, M3 BUMPER, HOLD DOWN SPACER, TONKER SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) HEX HEAD, FLANGED, M5 x 8mm LONG SPACER, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION .042 DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION F PREMIUM SPACER, CRIMPER CRIMPER, WIRE .042 F PREMIUM PART NO -77 -27 -25 -22 -21 PACIFIC VERSION AMP 4805 REV 31MAR2000 66 2063440-1 - 1.78 mm [.070] A PART NUMBERS REQUIRED F F 1.07 mm [.042] REVISIONS DIST - - APPLICATOR DATA LOC 1 Ocean Side Feed Applicator - DRAWING NO 2151011 SCALE 1:2 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV F D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 20 6 1 REVISIONS DIST 66 P LTR DESCRIPTION SEE SHEET 1 - FEED TYPE DWN APVD - - - 251 MECHANICAL 62 6 40 A D DATE 145 38 239 246 39 59 7 56 140 152 2 D 2 2 244 7 139 243 PNEUMATIC 250 2 8 249 242 2 6 63 238 A 166 8 0.0 REF 163 34 59 1 50 137 C 82 53 136 1 TERMINAL SUPPORT LOCATION 2 52 172 3 51 56 REF C 1 4 28 SERVO LATCH PLATE 5 41 240 133 4 135 198 164 66 2 A 33 SERVO FEEDER NOT INCLUDED 213 A 24 B 67 11 19 10 30 20 117 REF B 21 9 29 1 12 241 13 1 11 151 REF REF 29 119 30mm STROKE 30mm STROKE 142 11 30 CAM POSITIONS 30mm STROKE ITEM 30 LOCATED AT FRONT HOLES 141 32 34 143 8 1 144 143 10 1 FEED TRACK POSITION GUIDE BY INSULATION BARREL 48 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. PACIFIC VERSION 49 MECHANICAL POST FEED 49 MECHANICAL PRE FEED 49 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: FINISH 03NOV2011 CHK 04NOV2011 APVD 04NOV2011 HOFFNER T.ELBIN T.ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES DWN - APPLICATION SPEC - - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean Side Feed Applicator - DRAWING NO 2151011 SCALE 1:2 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV F