ON NCP45521IMNTWG-L Advanced load management Datasheet

NCP45520, NCP45521
ecoSWITCHt
Advanced Load Management
Controlled Load Switch with Low RON
The NCP4552x series of load switches provide a component and
area-reducing solution for efficient power domain switching with
inrush current limit via soft start. In addition to integrated control
functionality with ultra low on−resistance, these devices offer system
safeguards and monitoring via fault protection and power good
signaling. This cost effective solution is ideal for power management
and hot-swap applications requiring low power consumption in a
small footprint.
Features
•
•
•
•
•
•
•
•
•
•
•
•
http://onsemi.com
RON TYP
VCC
VIN
9.5 mW
3.3 V
1.8 V
10.1 mW
3.3 V
5.0 V
12.8 mW
3.3 V
12 V
Advanced Controller with Charge Pump
Integrated N-Channel MOSFET with Low RON
Input Voltage Range 0.5 V to 13.5 V
Soft-Start via Controlled Slew Rate
Adjustable Slew Rate Control (NCP45521)
Power Good Signal (NCP45520)
Thermal Shutdown
Undervoltage Lockout
Short-Circuit Protection
Extremely Low Standby Current
Load Bleed (Quick Discharge)
This is a Pb−Free Device
DFN8, 2x2
CASE 506CC
MARKING DIAGRAM
1
XX MG
G
XX = PH for NCP45520−H
= PL for NCP45520−L
= SH for NCP45521−H
= SL for NCP45521−L
M = Date Code
G
= Pb−Free Package
Portable Electronics and Systems
Notebook and Tablet Computers
Telecom, Networking, Medical, and Industrial Equipment
Set−Top Boxes, Servers, and Gateways
Hot Swap Devices and Peripheral Ports
VCC
EN
10.5 A
1
Typical Applications
•
•
•
•
•
IMAX
(Note: Microdot may be in either location)
VIN
PG*
PIN CONFIGURATION
Bandgap
&
Biases
Thermal,
Undervoltage
&
Short−Circuit
Protection
Control
Logic
VIN
1
8
VOUT
EN
2
7
VOUT
VCC
3
6
PG or SR
GND
4
5
BLEED
9: VIN
Charge
Pump
Delay and
Slew Rate
Control
(Top View)
SR*
GND
BLEED
VOUT
Figure 1. Block Diagram
(*Note: either PG or SR available for each part)
© Semiconductor Components Industries, LLC, 2014
September, 2014 − Rev. 3
ORDERING INFORMATION
See detailed ordering and shipping information on page 14 of
this data sheet.
1
Publication Order Number:
NCP45520/D
NCP45520, NCP45521
Table 1. PIN DESCRIPTION
Pin
Name
Function
1, 9
VIN
Drain of MOSFET (0.5 V – 13.5 V), Pin 1 must be connected to Pin 9
2
EN
NCP45520−H & NCP45521−H − Active−high digital input used to turn on the MOSFET, pin
has an internal pull down resistor to GND
NCP45520−L & NCP45521−L − Active−low digital input used to turn on the MOSFET, pin has
an internal pull up resistor to VCC
3
VCC
Supply voltage to controller (3.0 V − 5.5 V)
4
GND
Controller ground
5
BLEED
6
PG
NCP45520 − Active−high, open−drain output that indicates when the gate of the MOSFET is
fully charged, external pull up resistor ≥ 1 kW to an external voltage source required; tie to
GND if not used
SR
NCP45521 − Slew rate adjustment; float if not used
7, 8
VOUT
Load bleed connection, must be tied to VOUT either directly or through a resistor ≤ 1 kW
Source of MOSFET connected to load
Table 2. ABSOLUTE MAXIMUM RATINGS
Rating
Symbol
Value
Unit
VCC
−0.3 to 6
V
Supply Voltage Range
Input Voltage Range
VIN
−0.3 to 18
V
Output Voltage Range
VOUT
−0.3 to 18
V
EN Digital Input Range
VEN
−0.3 to (VCC + 0.3)
V
PG Output Voltage Range (Note 1)
VPG
−0.3 to 6
V
Thermal Resistance, Junction−to−Ambient, Steady State (Note 2)
RθJA
40.0
°C/W
Thermal Resistance, Junction−to−Ambient, Steady State (Note 3)
RθJA
72.7
°C/W
Thermal Resistance, Junction−to−Case (VIN Paddle)
RθJC
5.3
°C/W
Continuous MOSFET Current @ TA = 25°C (Notes 2 and 4)
IMAX
10.5
A
Continuous MOSFET Current @ TA = 25°C (Notes 3 and 4)
IMAX
7.8
A
Total Power Dissipation @ TA = 25°C (Note 2)
Derate above TA = 25°C
PD
2.50
24.9
W
mW/°C
Total Power Dissipation @ TA = 25°C (Note 3)
Derate above TA = 25°C
PD
1.37
13.8
W
mW/°C
Storage Temperature Range
TSTG
−40 to 150
°C
Lead Temperature, Soldering (10 sec.)
TSLD
260
°C
ESD Capability, Human Body Model (Notes 5 and 6)
ESDHBM
3.0
kV
ESD Capability, Machine Model (Note 5)
ESDMM
200
V
ESD Capability, Charged Device Model (Note 5)
ESDCDM
1.0
kV
LU
100
mA
Latch−up Current Immunity (Notes 5 and 6)
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. NCP45520 only. PG is an open−drain output that requires an external pull up resistor ≥ 1 kW to an external voltage source.
2. Surface−mounted on FR4 board using 1 sq−in pad, 1 oz Cu.
3. Surface−mounted on FR4 board using the minimum recommended pad size, 1 oz Cu.
4. Ensure that the expected operating MOSFET current will not cause the Short−Circuit Protection to turn the MOSFET off undesirably.
5. Tested by the following methods @ TA = 25°C:
ESD Human Body Model tested per JESD22−A114
ESD Machine Model tested per JESD22−A115
ESD Charged Device Model tested per JESD22−C101
Latch−up Current tested per JESD78
6. Rating is for all pins except for VIN and VOUT which are tied to the internal MOSFET’s Drain and Source. Typical MOSFET ESD performance
for VIN and VOUT should be expected and these devices should be treated as ESD sensitive.
http://onsemi.com
2
NCP45520, NCP45521
Table 3. OPERATING RANGES
Rating
Symbol
Min
Max
Unit
Supply Voltage
VCC
3
5.5
V
Input Voltage
VIN
0.5
13.5
V
0
V
Ground
GND
Ambient Temperature
TA
−40
85
°C
Junction Temperature
TJ
−40
125
°C
Table 4. ELECTRICAL CHARACTERISTICS (TJ = 25°C unless otherwise specified)
Conditions (Note 7)
Typ
Max
Unit
9.5
12.7
mW
VCC = 3.3 V; VIN = 5 V
10.1
13.9
VCC = 3.3 V; VIN = 12 V
12.8
22.5
Parameter
Symbol
Min
MOSFET
On−Resistance
Leakage Current (Note 8)
VCC = 3.3 V; VIN = 1.8 V
RON
VEN = 0 V; VIN = 13.5 V
ILEAK
0.1
1
mA
VEN = 0 V; VCC = 3 V
ISTBY
0.65
2
mA
3.2
4.5
IDYN
280
400
530
750
86
115
144
72
97
121
6
10
60
70
CONTROLLER
Supply Standby Current (Note 9)
VEN = 0 V; VCC = 5.5 V
Supply Dynamic Current (Note 10)
VEN = VCC = 3 V; VIN = 12 V
VEN = VCC = 5.5 V; VIN = 1.8 V
Bleed Resistance
RBLEED
VEN = 0 V; VCC = 3 V
VEN = 0 V; VCC = 5.5 V
Bleed Pin Leakage Current
VEN = VCC = 3 V, VIN = 1.8 V
IBLEED
VEN = VCC = 3 V, VIN = 12 V
EN Input High Voltage
VCC = 3 V − 5.5 V
VIH
EN Input Low Voltage
VCC = 3 V − 5.5 V
VIL
EN Input Leakage Current
NCP45520−H; NCP45521−H; VEN = 0 V
IIL
NCP45520−L; NCP45521−L; VEN = 5.5 V
IIH
2
mA
W
mA
V
0.8
V
90
500
nA
90
500
EN Pull Down Resistance
NCP45520−H; NCP45521−H
RPD
76
100
124
kW
EN Pull Up Resistance
NCP45520−L; NCP45521−L
RPU
76
100
124
kW
PG Output Low Voltage (Note 11)
NCP45520; VCC = 3 V; ISINK = 5 mA
VOL
0.2
V
PG Output Leakage Current (Note 12)
NCP45520; VCC = 3 V; VTERM = 3.3 V
IOH
5
100
nA
Slew Rate Control Constant (Note 13)
NCP45521; VCC = 3 V
KSR
31
38
mA
Thermal Shutdown Threshold (Note 14)
VCC = 3 V − 5.5 V
TSDT
145
°C
Thermal Shutdown Hysteresis (Note 14)
VCC = 3 V − 5.5 V
THYS
20
°C
VIN Undervoltage Lockout Threshold
VCC = 3 V
VUVLO
VIN Undervoltage Lockout Hysteresis
VCC = 3 V
VHYS
20
Short−Circuit Protection Threshold
VCC = 3 V; VIN = 0.5 V
VSC
200
100
285
500
24
FAULT PROTECTIONS
VCC = 3 V; VIN = 13.5 V
0.25
0.35
0.45
V
50
70
mV
265
350
mV
7. VEN shown only for NCP45520−H, NCP45521−H (EN Active−High) unless otherwise specified.
8. Average current from VIN to VOUT with MOSFET turned off.
9. Average current from VCC to GND with MOSFET turned off.
10. Average current from VCC to GND after charge up time of MOSFET.
11. PG is an open-drain output that is pulled low when the MOSFET is disabled.
12. PG is an open-drain output that is not driven when the gate of the MOSFET is fully charged, requires an external pull up resistor ≥ 1 kW to
an external voltage source, VTERM.
13. See Applications Information section for details on how to adjust the slew rate.
14. Operation above TJ = 125°C is not guaranteed.
http://onsemi.com
3
NCP45520, NCP45521
Table 5. SWITCHING CHARACTERISTICS (TJ = 25°C unless otherwise specified) (Notes 15 and 16)
Conditions
Parameter
Symbol
Min
Typ
VCC = 3.3 V; VIN = 1.8 V
12.1
SR
VCC = 3.3 V; VIN = 12 V
Output Turn−on Delay (Note 17)
Output Turn−off Delay (Note 17)
Power Good Turn−on Time (Note 18)
Power Good Turn−off Time (Note 18)
13.5
VCC = 5.0 V; VIN = 12 V
13.9
VCC = 3.3 V; VIN = 1.8 V
220
VCC = 5.0 V; VIN = 1.8 V
185
TON
VCC = 3.3 V; VIN = 12 V
270
VCC = 5.0 V; VIN = 12 V
260
VCC = 3.3 V; VIN = 1.8 V
1.2
VCC = 5.0 V; VIN = 1.8 V
0.9
TOFF
VCC = 3.3 V; VIN = 12 V
0.4
VCC = 5.0 V; VIN = 12 V
0.2
VCC = 3.3 V; VIN = 1.8 V
0.91
VCC = 5.0 V; VIN = 1.8 V
1.33
VCC = 5.0 V; VIN = 12 V
1.21
VCC = 3.3 V; VIN = 1.8 V
21
VCC = 5.0 V; VIN = 1.8 V
21
VCC = 5.0 V; VIN = 12 V
15
15. See below figure for Test Circuit and Timing Diagram.
16. Tested with the following conditions: VTERM = VCC; RPG = 100 kW; RL = 10 W; CL = 0.1 mF.
17. Applies to NCP45520 and NCP45521.
18. Applies only to NCP45520.
VTERM
RPG
VIN
PG
NCP4552x−H
GND
VEN
RL
SR
50%
TON
CL
50%
Dt
TOFF
90%
VOUT
VOUT
BLEED
VCC
10%
DV
SR =
TPG,ON
DV
90%
Dt
TPG,OFF
50%
50%
VPG
Figure 2. Switching Characteristics Test Circuit and Timing Diagram
http://onsemi.com
4
ms
ms
ms
15
TPG,OFF
VCC = 3.3 V; VIN = 12 V
EN
kV/s
0.93
TPG,ON
VCC = 3.3 V; VIN = 12 V
OFF ON
Unit
11.9
VCC = 5.0 V; VIN = 1.8 V
Output Slew Rate (Note 17)
Max
ns
NCP45520, NCP45521
TYPICAL CHARACTERISTICS
(TJ = 25°C unless otherwise specified)
16.5
20
15.5
18
RON, ON−RESISTANCE (mW)
RON, ON−RESISTANCE (mW)
VIN = 12 V
14.5
13.5
12.5
11.5
VCC = 3 V
10.5
VCC = 5.5 V
9.5
16
6.5
8.5
10.5
12
VIN = 1.8 V
10
8
6
−45 −30 −15
12.5
0
15
30
45
60
75
90 105 120
TJ, JUNCTION TEMPERATURE (°C)
Figure 3. On−Resistance vs. Input Voltage
Figure 4. On−Resistance vs. Temperature
ISTBY, SUPPLY STANDBY CURRENT (mA)
VIN, INPUT VOLTAGE (V)
3.0
2.5
2.0
1.5
1.0
0.5
3.5
4.0
4.5
5.0
5.5
7
6
5
4
VCC = 5.5 V
3
2
1
VCC = 3 V
0
−45 −30 −15
0
15
30
45
60
75
90 105 120
VCC, SUPPLY VOLTAGE (V)
TJ, JUNCTION TEMPERATURE (°C)
Figure 5. Supply Standby Current vs. Supply
Voltage
Figure 6. Supply Standby Current vs.
Temperature
IDYN, SUPPLY DYNAMIC CURRENT (mA)
ISTBY, SUPPLY STANDBY CURRENT (mA)
4.5
3.5
3.0
IDYN, SUPPLY DYNAMIC CURRENT (mA)
2.5
VIN = 5.0 V
14
8.5
0.5
VCC = 3.3 V
550
500
450
400
350
300
VCC = 5.5 V
250
VCC = 3 V
200
150
0.5
2.5
4.5
6.5
8.5
10.5
600
550
500
VIN = 1.8 V
450
400
350
300
VIN = 12 V
250
200
150
3.0
12.5
3.5
4.0
4.5
5.0
5.5
VIN, INPUT VOLTAGE (V)
VCC, SUPPLY VOLTAGE (V)
Figure 7. Supply Dynamic Current vs. Input
Voltage
Figure 8. Supply Dynamic Current vs. Supply
Voltage
http://onsemi.com
5
NCP45520, NCP45521
TYPICAL CHARACTERISTICS
115
700
RBLEED, BLEED RESISTANCE (W)
IDYN, SUPPLY DYNAMIC CURRENT (mA)
(TJ = 25°C unless otherwise specified)
VCC = 5.5 V, VIN = 1.8 V
650
600
550
500
450
400
350
300
250
200
−45
VCC = 3.0 V, VIN = 12 V
110
105
100
95
−15
15
45
75
3.0
105
4.5
5.0
5.5
TJ, JUNCTION TEMPERATURE (°C)
VCC, SUPPLY VOLTAGE (V)
Figure 10. Bleed Resistance vs. Supply
Voltage
IBLEED, BLEED PIN LEAKAGE
CURRENT (mA)
70
135
VCC = 3 V
125
115
VCC = 5.5 V
105
95
85
−45
60
VCC = 3 V
50
VCC = 5.5 V
40
30
20
10
0
−15
15
45
75
105
0.5
2.5
4.5
6.5
8.5
10.5
12.5
TJ, JUNCTION TEMPERATURE (°C)
VIN, INPUT VOLTAGE (V)
Figure 11. Bleed Resistance vs. Temperature
Figure 12. Bleed Pin Leakage Current vs. Input
Voltage
IPD/PU, EN PULL DOWN/UP RESISTANCE (kW)
RBLEED, BLEED RESISTANCE (W)
4.0
Figure 9. Supply Dynamic Current vs.
Temperature
145
IBLEED, BLEED PIN LEAKAGE CURRENT (mA)
3.5
80
70
VCC = 3 V, VIN = 12 V
60
50
40
30
20
VCC = 3 V, VIN = 1.8 V
10
0
−45
−15
15
45
75
105
120
115
110
105
100
95
90
85
−45
−15
15
45
75
105
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 13. Bleed Pin Leakage Current vs.
Temperature
Figure 14. EN Pull Down/Up Resistance vs.
Temperature
http://onsemi.com
6
NCP45520, NCP45521
TYPICAL CHARACTERISTICS
ISINK = 5 mA
0.135
0.130
0.125
0.120
0.115
0.110
3.0
3.5
4.0
4.5
5.0
5.5
0.20
ISINK = 5 mA
0.18
VCC = 3 V
0.16
0.14
VCC = 5.5 V
0.12
0.10
0.08
−45
−15
15
45
75
105
TJ, JUNCTION TEMPERATURE (°C)
Figure 15. PG Output Low Voltage vs. Supply
Voltage
Figure 16. PG Output Low Voltage vs.
Temperature
KSR, SLEW RATE CONTROL CONSTANT (mA)
VCC, SUPPLY VOLTAGE (V)
34
33
VCC = 5.5 V
32
VCC = 3 V
31
30
29
VSC, SHORT−CIRCUIT PROTECTION
THRESHOLD (mV)
KSR, SLEW RATE CONTROL CONSTANT (mA)
VOL, PG OUTPUT LOW VOLTAGE (V)
0.140
0.5
2.5
4.5
6.5
8.5
10.5
12.5
35
34
VCC = 5.5 V
33
32
31
VCC = 3 V
30
29
28
−45
−15
15
45
75
105
VIN, INPUT VOLTAGE (V)
TJ, JUNCTION TEMPERATURE (°C)
Figure 17. Slew Rate Control Constant vs.
Input Voltage
Figure 18. Slew Rate Control Constant vs.
Temperature
15
320
SR, OUTPUT SLEW RATE (kV/s)
VOL, PG OUTPUT LOW VOLTAGE (V)
(TJ = 25°C unless otherwise specified)
310
VCC = 5.5 V
300
290
VCC = 3 V
280
270
260
14
VCC = 5.5 V
13
VCC = 3 V
12
11
10
9
8
250
0.5
2.5
4.5
6.5
8.5
10.5
0.5
12.5
2.5
4.5
6.5
8.5
10.5
12.5
VIN, INPUT VOLTAGE (V)
VIN, INPUT VOLTAGE (V)
Figure 19. Short−Circuit Protection Threshold
vs. Input Voltage
Figure 20. Output Slew Rate vs. Input Voltage
http://onsemi.com
7
NCP45520, NCP45521
TYPICAL CHARACTERISTICS
(TJ = 25°C unless otherwise specified)
13.0
12.5
12.0
VCC = 5 V, VIN = 1.8 V
11.5
11.0
−20
0
20
40
60
80
100
310
290
270
VCC = 3 V
250
VCC = 5.5 V
230
210
190
170
150
0.5
120
2.5
4.5
6.5
8.5
10.5
12.5
TJ, JUNCTION TEMPERATURE (°C)
VIN, INPUT VOLTAGE (V)
Figure 21. Output Slew Rate vs. Temperature
Figure 22. Output Turn−on Delay vs. Input
Voltage
300
TOFF, OUTPUT TURN−OFF DELAY (ms)
TON, OUTPUT TURN−ON DELAY (ms)
10.5
−40
TOFF, OUTPUT TURN−OFF DELAY (ms)
TON, OUTPUT TURN−ON DELAY (ms)
VCC = 3.3 V, VIN = 12 V
13.5
VCC = 3.3 V, VIN = 12 V
275
250
225
200
VCC = 5 V, VIN = 1.8 V
175
150
−40
−20
0
20
40
60
80
100
1.6
1.4
1.2
1.0
VCC = 3 V
0.8
0.6
VCC = 5.5 V
0.4
0.2
0
0.5
2.5
4.5
6.5
8.5
10.5
12.5
TJ, JUNCTION TEMPERATURE (°C)
VIN, INPUT VOLTAGE (V)
Figure 23. Output Turn−on Delay vs.
Temperature
Figure 24. Output Turn−off Delay vs. Input
Voltage
1.8
1.2
VCC = 5 V, VIN = 1.8 V
1.0
0.8
0.6
VCC = 3.3 V, VIN = 12 V
0.4
0.2
−40
1.8
120
TPG,ON, PG TURN−ON TIME (ms)
SR, OUTPUT SLEW RATE (kV/s)
14.0
−20
0
20
40
60
80
100
1.7
1.6
1.5
1.4
VCC = 3 V
1.3
1.2
1.1
VCC = 5.5 V
1.0
0.9
0.8
0.5
120
2.5
4.5
6.5
8.5
10.5
12.5
TJ, JUNCTION TEMPERATURE (°C)
VIN, INPUT VOLTAGE (V)
Figure 25. Output Turn−off Delay vs.
Temperature
Figure 26. Power Good Turn−on Time vs. Input
Voltage
http://onsemi.com
8
NCP45520, NCP45521
TYPICAL CHARACTERISTICS
(TJ = 25°C unless otherwise specified)
24
TPG,OFF, PG TURN−OFF TIME (ns)
1.4
VCC = 3.3 V, VIN = 12 V
1.3
1.2
1.1
1.0
VCC = 5 V, VIN = 1.8 V
0.9
0.8
−40
22
VIN = 13.5 V
20
VIN = 0.5 V
18
16
14
12
−20
0
20
40
60
80
3.0
120
100
3.5
4.0
4.5
5.0
TJ, JUNCTION TEMPERATURE (°C)
VCC, SUPPLY VOLTAGE (V)
Figure 27. Power Good Turn−on Time vs.
Temperature
Figure 28. Power Good Turn−off Time vs.
Supply Voltage
27.5
TPG,OFF, PG TURN−OFF TIME (ns)
TPG,ON, PG TURN−ON TIME (ms)
1.5
25.0
VCC = 3.3 V, VIN = 12 V
22.5
20.0
17.5
VCC = 5 V, VIN = 1.8 V
15.0
12.5
10.0
−40 −20
0
20
40
60
80
100
TJ, JUNCTION TEMPERATURE (°C)
Figure 29. Power Good Turn−off Time vs.
Temperature
http://onsemi.com
9
120
5.5
NCP45520, NCP45521
APPLICATIONS INFORMATION
Enable Control
The power good output can be used as the enable signal for
other active−high devices in the system (as shown in
Figure 32). This allows for guaranteed by design power
sequencing and reduces the number of enable signals needed
from the system controller. If the power good feature is not
used in the application, the PG pin should be tied to GND.
Both the NCP45520 and the NCP45521 have two part
numbers, NCP4552x-H and NCP4552x-L, that only differ
in the polarity of the enable control.
The NCP4552x-H devices allow for enabling the
MOSFET in an active-high configuration. When the VCC
supply pin has an adequate voltage applied and the EN pin
is at a logic high level, the MOSFET will be enabled.
Similarly, when the EN pin is at a logic low level, the
MOSFET will be disabled. An internal pull down resistor to
ground on the EN pin ensures that the MOSFET will be
disabled when not being driven.
The NCP4552x-L devices allow for enabling the
MOSFET in an active-low configuration. When the VCC
supply pin has an adequate voltage applied and the EN pin
is at a logic low level, the MOSFET will be enabled.
Similarly, when the EN pin is at a logic high level, the
MOSFET will be disabled. An internal pull up resistor to
VCC on the EN pin ensures that the MOSFET will be
disabled when not being driven.
Slew Rate Control
The NCP4552x devices are equipped with controlled
output slew rate which provides soft start functionality. This
limits the inrush current caused by capacitor charging and
enables these devices to be used in hot swap applications.
The slew rate of the NCP45521 can be decreased with an
external capacitor added between the SR pin and ground (as
shown in Figures 33 and 34). With an external capacitor
present, the slew rate can be determined by the following
equation:
Slew Rate +
K SR
[Vńs]
C SR
(eq. 1)
where KSR is the specified slew rate control constant, found
in Table 4, and CSR is the slew rate control capacitor added
between the SR pin and ground. The slew rate of the device
will always be the lower of the default slew rate and the
adjusted slew rate. Therefore, if the CSR is not large enough
to decrease the slew rate more than the specified default
value, the slew rate of the device will be the default value.
The SR pin can be left floating if the slew rate does not need
to be decreased.
Power Sequencing
The NCP4552x devices will function with any power
sequence, but the output turn−on delay performance may
vary from what is specified. To achieve the specified
performance, there are two recommended power sequences:
1) VCC → VIN → VEN
2) VIN → VCC → VEN
Load Bleed (Quick Discharge)
The NCP4552x devices have an internal bleed resistor,
RBLEED, which is used to bleed the charge off of the load to
ground after the MOSFET has been disabled. In series with
the bleed resistor is a bleed switch that is enabled whenever
the MOSFET is disabled. The MOSFET and the bleed
switch are never concurrently active.
It is required that the BLEED pin be connected to VOUT
either directly (as shown in Figures 31 and 34) or through an
external resistor, REXT (as shown in Figures 30 and 33).
REXT should not exceed 1 kW and can be used to increase the
total bleed resistance.
Care must be taken to ensure that the power dissipated
across RBLEED is kept at a safe level. The maximum
continuous power that can be dissipated across RBLEED is
0.4 W. REXT can be used to decrease the amount of power
dissipated across RBLEED.
Short−Circuit Protection
The NCP4552x devices are equipped with short−circuit
protection that is used to help protect the part and the system
from a sudden high−current event, such as the output, VOUT,
being shorted to ground. This circuitry is only active when
the gate of the MOSFET is fully charged.
Once active, the circuitry monitors the difference in the
voltage on the VIN pin and the voltage on the BLEED pin.
In order for the VOUT voltage to be monitored through the
BLEED pin, it is required that the BLEED pin be connected
to VOUT either directly (as shown in Figures 31 and 34) or
through a resistor, REXT (as shown in Figures 30 and 33),
which should not exceed 1 kW. With the BLEED pin
connected to VOUT, the short−circuit protection is able to
monitor the voltage drop across the MOSFET.
If the voltage drop across the MOSFET is greater than or
equal to the short−circuit protection threshold voltage, the
MOSFET is immediately turned off and the load bleed is
activated. The part remains latched in this off state until EN
is toggled or VCC supply voltage is cycled, at which point the
MOSFET will be turned on in a controlled fashion with the
normal output turn−on delay and slew rate. The current
through the MOSFET that will cause a short−circuit event
can be calculated by dividing the short−circuit protection
threshold by the expected on−resistance of the MOSFET.
Power Good
The NCP45520 devices have a power good output (PG)
that can be used to indicate when the gate of the MOSFET
is fully charged. The PG pin is an active-high, open-drain
output that requires an external pull up resistor, RPG, greater
than or equal to 1 kW to an external voltage source, VTERM,
that is compatible with input levels of all devices connected
to this pin (as shown in Figures 30 and 31).
http://onsemi.com
10
NCP45520, NCP45521
Thermal Shutdown
Undervoltage Lockout
The thermal shutdown of the NCP4552x devices protects
the part from internally or externally generated excessive
temperatures. This circuitry is disabled when EN is not
active to reduce standby current. When an over-temperature
condition is detected, the MOSFET is immediately turned
off and the load bleed is activated.
The part comes out of thermal shutdown when the
junction temperature decreases to a safe operating
temperature as dictated by the thermal hysteresis. Upon
exiting a thermal shutdown state, and if EN remains active,
the MOSFET will be turned on in a controlled fashion with
the normal output turn-on delay and slew rate.
The undervoltage lockout of the NCP4552x devices turns
the MOSFET off and activates the load bleed when the input
voltage, VIN, is less than or equal to the undervoltage
lockout threshold. This circuitry is disabled when EN is not
active to reduce standby current.
If the VIN voltage rises above the undervoltage lockout
threshold, and EN remains active, the MOSFET will be
turned on in a controlled fashion with the normal output
turn-on delay and slew rate.
VTERM = 3.3 V
RPG
100 kW
3.0 V − 5.5 V
Power Supply
or Battery
0.5 V − 13.5 V
Controller
VCC
EN
VIN
PG
Bandgap
&
Biases
Control
Logic
Charge
Pump
Delay and
Slew Rate
Control
Thermal,
Undervoltage
&
Short−Circuit
Protection
GND
BLEED
VOUT
REXT
Load
Figure 30. NCP45520 Typical Application Diagram − Load Switch
http://onsemi.com
11
NCP45520, NCP45521
VCC
3.0 V − 5.5 V
PG VTERM
EN
GND
VIN
0.5 V − 13.5 V
RPG
BACKPLANE
REMOVABLE
CARD
VCC
EN
VIN
PG
Bandgap
&
Biases
Control
Logic
Charge
Pump
Delay and
Slew Rate
Control
Thermal,
Undervoltage
&
Short−Circuit
Protection
GND
VOUT
BLEED
Load
Figure 31. NCP45520 Typical Application Diagram − Hot Swap
VTERM = 3.3 V
EN
PG
EN
PG
RPG
10 kW
Controller
RPD
100 kW
RPD
100 kW
PG
PG
NCP45520−H
NCP45520−H
Figure 32. NCP45520 Simplified Application Diagram − Power Sequencing with PG Output
http://onsemi.com
12
NCP45520, NCP45521
Power Supply
or Battery
3.0 V − 5.5 V
Controller
0.5 V − 13.5 V
EN
VCC
VIN
Thermal,
Undervoltage
&
Short−Circuit
Protection
Bandgap
&
Biases
Control
Logic
Charge
Pump
Delay and
Slew Rate
Control
SR
GND
VOUT
BLEED
CSR
REXT
Load
Figure 33. NCP45521 Typical Application Diagram − Load Switch
VCC
3.0 V − 5.5 V
GND
EN
VIN
0.5 V − 13.5 V
BACKPLANE
REMOVABLE
CARD
VCC
EN
Bandgap
&
Biases
Control
Logic
Charge
Pump
Delay and
Slew Rate
Control
VIN
Thermal,
Undervoltage
&
Short−Circuit
Protection
SR
GND
BLEED
VOUT
CSR
Load
Figure 34. NCP45521 Typical Application Diagram − Hot Swap
http://onsemi.com
13
NCP45520, NCP45521
ORDERING INFORMATION
Device
Pin 6 Functionality
EN Polarity
NCP45520IMNTWG−H
PG
Active−High
NCP45520IMNTWG−L
PG
Active−Low
NCP45521IMNTWG−H
SR
Active−High
NCP45521IMNTWG−L
SR
Active−Low
Package
Shipping†
DFN8
(Pb−Free)
3000 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
14
NCP45520, NCP45521
PACKAGE DIMENSIONS
DFN8 2x2, 0.5P
CASE 506CC
ISSUE O
A
D
L
E
DETAIL A
ALTERNATE
CONSTRUCTIONS
0.10 C
2X
0.10 C
2X
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.15 AND 0.30 MM FROM TERMINAL TIP.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
L
L1
ÇÇ
ÇÇ
PIN ONE
REFERENCE
B
TOP VIEW
DIM
A
A1
A3
b
D
D2
E
E2
e
K
L
L1
MOLD CMPD
ÇÇ
ÉÉ
ÉÉ
EXPOSED Cu
DETAIL B
A
0.10 C
A3
A1
0.08 C
A1
SIDE VIEW
NOTE 4
A3
DETAIL B
C
SEATING
PLANE
ALTERNATE
CONSTRUCTION
MILLIMETERS
MIN
MAX
0.80
1.00
0.00
0.05
0.20 REF
0.20
0.30
2.00 BSC
1.50
1.70
2.00 BSC
0.80
1.00
0.50 BSC
0.27 REF
0.18
0.38
−−−
0.15
D2
DETAIL A
8X
1
L
4
RECOMMENDED
SOLDERING FOOTPRINT*
E2
K
8
5
e
e/2
8X
PACKAGE
OUTLINE
1.70
8X
0.50
b
0.20
0.10 C A B
0.05 C
NOTE 3
2.30
1.00
BOTTOM VIEW
1
0.50
PITCH
8X
0.30
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ecoSWITCH is a trademark of Semiconductor Components Industries, LLC (SCILLC).
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
15
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCP45520/D
Similar pages