TI1 ERJ-2RKF1503X 2.5-w mono class-d audio amplifier with auto-recovery Datasheet

TPA2036D1
www.ti.com.............................................................................................................................................................................................. SLOS589 – OCTOBER 2008
2.5-W MONO CLASS-D AUDIO AMPLIFIER WITH AUTO-RECOVERY
FEATURES
APPLICATIONS
• Pin-to-pin compatibility with TPA2010D1
• Short Circuit Auto-recovery
• Maximum Battery Life and Minimum Heat
– Efficiency With an 8-Ω Speaker:
– 88% at 400 mW
– 80% at 100 mW
– 2.8-mA Quiescent Current
– 0.5-µA Shutdown Current
• Only Three External Components
– Optimized PWM Output Stage Eliminates
LC Output Filter
– High PSRR (–75 dB) and Wide Supply
Voltage (2.5 V to 5.5 V)
– Fully Differential Design Reduces RF
Rectification and Eliminates Bypass
Capacitor
– Improved CMRR Eliminates Two Input
Coupling Capacitors
• 1,45mm × 1,45 mm 9-Ball WCSP
– NanoFree™ Lead-Free (YZF)
•
•
•
•
1
2
Wireless or Cellular Handsets and PDAs
Personal Navigation Devices
General Portable Audio Devices
Linear Vibrator Drivers
SEE ALSO
•
TPA2031D1, TPA2032D1, TPA2033D1,
TPA2034D1, TPA2035D1
DESCRIPTION
The TPA2036D1 is a 2.5-W high efficiency filter-free
class-D audio power amplifier (class-D amp) in a 1,45
mm × 1,45 mm wafer chip scale package (WCSP)
that requires only three external components.
Features such as 88% efficiency, –75-dB PSRR,
improved RF immunity, and 8 mm2 total PCB area
make TPA2036D1 ideal for cellular handsets. A fast
start-up time of 1 ms with minimal pop makes
TPA2036D1 ideal for portable applications.
In cellular handsets, TPA2036D1 is capable of driving
the earpiece, speaker phone, and melody ringer.
TPA2036D1 allows independent gain while summing
signals from separate sources, and has a low 36
µVRMS noise floor, A-weighted.
APPLICATION CIRCUIT
To Battery
Internal
Oscillator
+
RI
Differential
Input
-
RI
VDD
CS
IN_
PWM
9-BALL
WAFER CHIP SCALE
YZF PACKAGE
TPA2036D1 DIMENSIONS
(TOP VIEW OF PCB)
VO+
HBridge
VO-
+
IN+
1,45 mm
IN+
GND
VO-
A1
A2
A3
VDD
V DD
GND
B1
B2
B3
GND
SHUTDOWN
Bias
Circuitry
INTPA2036D1
C1
SHUTDOWN VO+
C2
C3
1,45 mm
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
NanoFree is a trademark of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2008, Texas Instruments Incorporated
TPA2036D1
SLOS589 – OCTOBER 2008.............................................................................................................................................................................................. www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ORDERING INFORMATION
(1)
TA
PACKAGE
–40°C to 85°C
9 ball, 1.45mm × 1.45mm WCSP
(+0,1 mm/-0,05 mm tolerance)
PART NUMBER
TPA2036D1YZF
SYMBOL
(1)
CVV
The YZF package is only available taped and reeled. To order add the suffix R to the end of the part number for a reel of 3000, or add
the suffix T to the end of the part number for a reel of 250 (e.g. TPA2036D1YZFR).
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range unless otherwise noted (1)
TPA2036D1
VDD
Supply voltage
VI
Input voltage
In active mode
–0.3 V to 6 V
In SHUTDOWN mode
–0.3 V to 7 V
–0.3 V to VDD + 0.3 V
Continuous total power dissipation
See Dissipation Rating Table
TA
Operating free-air temperature
–40°C to 85°C
TJ
Operating junction temperature
–40°C to 150°C
Tstg
Storage temperature
–65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds
(1)
YZF
260°C
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
MIN
NOM
MAX
UNIT
VDD
Supply voltage
2.5
5.5
V
VIH
High-level input voltage
SHUTDOWN
1.3
VDD
V
VIL
Low-level input voltage
SHUTDOWN
0
0.35
V
RI
Input resistor
Gain ≤ 20 V/V (26 dB)
VIC
Common mode input voltage range VDD = 2.5 V, 5.5 V, CMRR ≤ –49 dB
0.5
VDD–0.8
V
TA
Operating free-air temperature
–40
85
°C
15
kΩ
PACKAGE DISSIPATION RATINGS
(1)
2
PACKAGE
DERATING FACTOR (1)
TA ≤ 25°C
POWER RATING
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
YZF
7.8 mW/°C
975 mW
624 mW
507 mW
Derating factor measure with JEDEC High K board. 1S2P - One signal layer and two plane layers. Please see JEDEC Standard 51-7 for
High-K board, and JEDEC Standard 51-12 for using package thermal information. Please see JEDEC document page for downloadable
copies: http://www.jedec.org/download/default.cfm.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2036D1
TPA2036D1
www.ti.com.............................................................................................................................................................................................. SLOS589 – OCTOBER 2008
ELECTRICAL CHARACTERISTICS
TA = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TYP
MAX
1
25
mV
VDD = 2.5 V to 5.5 V
–75
–55
dB
Common mode rejection ratio
VDD = 2.5 V to 5.5 V, VIC = VDD/2 to 0.5 V,
VIC = VDD/2 to VDD –0.8 V
–68
–49
dB
|IIH|
High-level input current
VDD = 5.5 V, VI = 5.8 V, SHUTDOWN
100
µA
|IIL|
Low-level input current
VDD = 5.5 V, VI = –0.3 V, SHUTDOWN
5
µA
|VOS|
Output offset voltage
(measured differentially)
VI = 0 V, AV = 2 V/V, VDD = 2.5 V to 5.5 V
PSRR
Power supply rejection ratio
CMRR
I(Q)
Quiescent current
I(SD)
Shutdown current
rDS(on)
Static drain-source on-state
resistance
Output impedance in SHUTDOWN
MIN
VDD = 5.5 V, no load
3.4
VDD = 3.6 V, no load
2.8
VDD = 2.5 V, no load
2.2
3.2
V(SHUTDOWN)= 0.35 V, VDD = 2.5 V to 5.5 V
0.5
2
VDD = 2.5 V
700
VDD = 3.6 V
500
VDD = 5.5 V
400
V(SHUTDOWN) = 0.35 V
4.9
mA
kΩ
2.3
A
Switching frequency
VDD = 2.5 V to 5.5 V
200
250
300
Gain
VDD = 2.5 V to 5.5 V
285 kW
RI
300 kW
RI
315 kW
RI
Resistance from SHUTDOWN to GND
µA
mΩ
2
Short circuit detection threshold
f(sw)
UNIT
300
kHz
V
V
kΩ
OPERATING CHARACTERISTICS
TA = 25°C, Gain = 2 V/V, RL = 8 Ω (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
VDD = 5 V
THD + N = 10%, f = 1 kHz, RL = 4 Ω
THD + N = 1%, f = 1 kHz, RL = 4 Ω
PO
Output power
THD + N = 10%, f = 1 kHz, RL = 8 Ω
THD + N = 1%, f = 1 kHz, RL = 8 Ω
THD+N
Total harmonic distortion plus
noise
TYP MAX
2.5
VDD = 3.6 V
1.3
VDD = 2.5 V
0.52
VDD = 5 V
2.08
VDD = 3.6 V
1.06
VDD = 2.5 V
0.42
VDD = 5 V
1.45
VDD = 3.6 V
0.73
VDD = 2.5 V
0.33
VDD = 5 V
1.19
VDD = 3.6 V
0.59
VDD = 2.5 V
0.26
VDD = 5 V, PO = 1 W, RL = 8 Ω, f = 1 kHz
0.18%
VDD = 3.6 V, PO = 0.5 W, RL = 8 Ω, f = 1 kHz
0.19%
VDD = 2.5 V, PO = 200 mW, RL = 8 Ω, f = 1 kHz
0.20%
kSVR
Supply ripple rejection ratio
VDD = 3.6 V, Inputs ac-grounded
with CI = 2 µF
f = 217 Hz,
V(RIPPLE) = 200 mVpp
SNR
Signal-to-noise ratio
VDD = 5 V, PO = 1 W, RL = 8 Ω
Vn
Output voltage noise
VDD = 3.6 V, f = 20 Hz to 20 kHz,
Inputs ac-grounded with CI = 2 µF
No weighting
48
A weighting
36
CMRR
Common mode rejection ratio
VDD = 3.6 V, VIC = 1 Vpp
f = 217 Hz
ZI
Input impedance
W
W
W
W
–67
dB
97
dB
µVRMS
–63
142
150
dB
158
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2036D1
UNIT
kΩ
3
TPA2036D1
SLOS589 – OCTOBER 2008.............................................................................................................................................................................................. www.ti.com
OPERATING CHARACTERISTICS (continued)
TA = 25°C, Gain = 2 V/V, RL = 8 Ω (unless otherwise noted)
PARAMETER
TEST CONDITIONS
Start-up time from shutdown
MIN
TYP MAX
VDD = 3.6 V
1
UNIT
ms
Terminal Functions
TERMINAL
NAME
I/O
YZF
DESCRIPTION
IN–
C1
I
Negative differential input
IN+
A1
I
Positive differential input
VDD
B1, B2
I
Power supply
VO+
C3
O
Positive BTL output
GND
A2, B3
I
High-current ground
VO-
A3
O
Negative BTL output
SHUTDOWN
C2
I
Shutdown terminal (active low logic)
FUNCTIONAL BLOCK DIAGRAM
Ω
Ω
Ω
SC
Ω
Ω
4
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2036D1
TPA2036D1
www.ti.com.............................................................................................................................................................................................. SLOS589 – OCTOBER 2008
TYPICAL CHARACTERISTICS
TABLE OF GRAPHS
FIGURE
Efficiency
vs Output power
1, 2
Power dissipation
vs Output power
3, 4
Supply current
vs Output power
5, 6
I(Q)
Quiescent current
vs Supply voltage
7
I(SD)
Shutdown current
vs Shutdown voltage
8
PD
PO
Output power
THD+N
Total harmonic distortion plus noise
vs Supply voltage
9
vs Load resistance
10, 11
vs Output power
12, 13
vs Frequency
14, 15, 16, 17
vs Common-mode input voltage
KSVR
Supply voltage rejection ratio
vs Frequency
GSM power supply rejection
KSVR
Supply voltage rejection ratio
CMRR
Common-mode rejection ratio
18
19, 20, 21
vs Time
22
vs Frequency
23
vs Common-mode input voltage
24
vs Frequency
25
vs Common-mode input voltage
26
TEST SET-UP FOR GRAPHS
CI
TPA2036D1
RI
IN+
+
Measurement
Output
-
CI
OUT+
Load
RI
INVDD
+
OUT-
30 kHz
Low Pass
Filter
+
Measurement
Input
-
GND
1 μF
VDD
-
Notes:
(1) C I was Shorted for any Common-Mode input voltage measurement
(2) A 33- μH inductor was placed in series with the load resistor to emulate a small speaker for efficiency measurements.
(3) The 30-kHz low-pass filter is required even if the analyzer has an internal low-pass filter. An RC low pass filter (100 Ω, 47 nF) is
used on each output for the data sheet graphs.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2036D1
5
TPA2036D1
SLOS589 – OCTOBER 2008.............................................................................................................................................................................................. www.ti.com
EFFICIENCY
vs
OUTPUT POWER
90
90
80
VDD = 5 V,
RL = 8 Ω, 33 µH
70
60
50
40
Class AB.
VDD = 5 V,
RL = 8 Ω
30
20
1.4
70
Efficiency − %
VDD = 2.5 V,
RL = 8 Ω, 33 µH
VDD = 3.6 V,
RL = 4 Ω, 33 µH
VDD = 2.5 V,
RL = 4 Ω, 33 µH
50
40
Class AB.
VDD = 5 V,
RL = 4 Ω
20
10
0
0.2
0.4
0.6
1
0.8
0
1.2
0.2
VDD = 5 V, RL = 8 Ω
0
1.2 1.4 1.6 1.8 2
0
0.5
1
1.5
2
Figure 2.
Figure 3.
POWER DISSIPATION
vs
OUTPUT POWER
SUPPLY CURRENT
vs
OUTPUT POWER
SUPPLY CURRENT
vs
OUTPUT POWER
Class-AB 3.6 V, 8 Ω
0.4
0.3
VDD = 3.6 V, RL = 4 Ω
0.2
0.1
VDD = 3.6 V,
RL = 8 Ω, 33 µH
0.2
0.4
0.6
0.8
1
400
VDD = 2.5 V
300
200
100
VDD = 5 V,
VDD = 3.6 V
200
150
100
VDD = 2.5 V
50
VDD = 5 V
0
0.5
1
1.5
2
0
2.5
0.2
0.4
0.6
0.8
1.2
1
PO − Output Power − W
PO − Output Power − W
PO − Output Power − W
Figure 4.
Figure 5.
Figure 6.
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
SUPPLY CURRENT
vs
SHUTDOWN VOLTAGE
OUTPUT POWER
vs
LOAD RESISTANCE
I (SD) − Shutdown Current − µ A
4.5
RL = 8 Ω, (resistive)
RL = 8 Ω,
33 µH
3.5
3
2.5
1.5
VDD = 5 V
1
VDD = 3.6 V
VDD = 2.5 V
0.5
4.5
5
5.5
VDD − Supply Voltage − V
Figure 7.
VDD = 5 V
2
VDD = 3.6 V
1.5
VDD = 2.5 V
1
0.5
0
0
4
PO at 10% THD
Gain = 2 V/V
f = 1 kHz
2.5
No Load
3.5
1.4
3
2
5
3
RL = 8 Ω, 33 µH
0
0
1.2
2.5
250
VDD = 3.6 V
I DD − Supply Current − mA
0.5
300
RL = 4 Ω, 33 µH
500
Class-AB 3.6 V, 4 Ω
I DD − Supply Current − mA
P D − Power Dissipation − W
VDD = 5 V, RL = 4 Ω,
0.4
Figure 1.
0
I DD − Supply Current − mA
0.6
PO − Output Power − W
0.6
2
2.5
Class-AB 5 V, 8 Ω
0.8
PO − Output Power − W
600
4
1
PO − Output Power − W
0.7
0
0.2 0.4 0.6 0.8 1
PO − Output Power − W
0 0
Class-AB 5 V, 4 Ω
1.2
VDD = 5 V,
RL = 4 Ω,
33 µH
60
30
10
6
POWER DISSIPATION
vs
OUTPUT POWER
P D − Power Dissipation − W
100
80
Efficiency − %
EFFICIENCY
vs
OUTPUT POWER
0
0.1
0.2
0.3
0.4
Shutdown Voltage − V
Figure 8.
Submit Documentation Feedback
0.5
4
8
12
16
20
24
28
32
RL − Load Resistance − Ω
Figure 9.
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2036D1
TPA2036D1
www.ti.com.............................................................................................................................................................................................. SLOS589 – OCTOBER 2008
3
2.5
VDD = 5 V
PO at 1% THD
Gain = 2 V/V
f = 1 kHz
1.5
VDD = 3.6 V
1
Gain = 2 V/V
f = 1 kHz
2.5
PO − Output Power − W
VDD = 2.5 V
0.5
RL = 4 Ω, 10% THD
2
RL = 4 Ω, 1% THD
1.5
1
RL = 8 Ω,10% THD
0.5
0
2.5
0
4
8
12
16
20
24
RL − Load Resistance − Ω
28
32
RL = 8 Ω,1% THD
3
3.5
4
4.5
VCC − Supply Voltage − V
5
20
RL = 4 Ω,
f = 1 kHz,
Gain = 2 V/V
10
5
2.5 V
3V
2
3.6 V
1
5V
0.5
0.2
0.1
20m
50m 100m 200m 500m 1
PO − Output Power − W
2
3
Figure 11.
Figure 12.
TOTAL HARMONIC DISTORTION +
NOISE
vs
OUTPUT POWER
TOTAL HARMONIC DISTORTION +
NOISE
vs
FREQUENCY
TOTAL HARMONIC DISTORTION +
NOISE
vs
FREQUENCY
20
RL = 8 Ω,
f = 1 kHz,
Gain = 2 V/V
10
5
2.5 V
3V
3.6 V
2
5V
1
0.5
0.2
0.1
5m 10m 20m 50m 100m 200m 500m 1
2
THD+N − Total Harmonic Distortion + Noise − %
Figure 10.
10
VDD = 5 V
CI = 2 µF
RL = 8 Ω
Gain = 2 V/V
5
2
PO = 50 mW
PO = 250 mW
1
0.5
PO = 1W
0.2
0.1
0.05
0.02
VDD = 3.6 V
CI = 2 µF
RL = 8 Ω
Gain = 2 V/V
5
2
PO = 25 mW
PO = 125 mW
1
0.5
PO = 500 mW
0.2
0.1
0.05
0.02
0.01
0.005
0.01
20
PO − Output Power − W
10
THD+N − Total Harmonic Distortion + Noise − %
PO − Output Power − W
2
THD+N − Total Harmonic Distortion + Noise − %
TOTAL HARMONIC DISTORTION +
NOISE
vs
OUTPUT POWER
OUTPUT POWER
vs
SUPPLY VOLTAGE
THD+N − Total Harmonic Distortion + Noise − %
OUTPUT POWER
vs
LOAD RESISTANCE
50 100 200
500 1k
2k
5k 10k 20k
20
50 100 200 500 1k 2k
f − Frequency − Hz
5k 10k 20k
Figure 15.
TOTAL HARMONIC DISTORTION +
NOISE
vs
FREQUENCY
TOTAL HARMONIC DISTORTION +
NOISE
vs
FREQUENCY
TOTAL HARMONIC DISTORTION +
NOISE
vs
COMMON MODE INPUT VOLTAGE
10
VDD = 2.5 V
CI = 2 µF
RL = 8 Ω
Gain = 2 V/V
5
2
PO = 15 mW
PO = 75 mW
1
0.5
PO = 200 mW
0.2
0.1
0.05
0.02
0.01
20
50 100 200 500 1k 2k
5k 10k 20k
f − Frequency − Hz
Figure 16.
10
PO = 250 mW
CI = 2 µF
RL = 4 Ω
Gain = 2 V/V
5
2
1
VDD = 3.6 V
VDD = 3 V
0.5
0.2
VDD = 2.5 V
0.1
0.05
0.02
0.01
VDD = 4 V
20
50 100 200
VDD = 5 V
500 1k 2k
5k 10k 20k
f − Frequency − Hz
Figure 17.
THD+N − Total Harmonic Distortion + Noise − %
Figure 14.
THD+N − Total Harmonic Distortion + Noise − %
THD+N − Total Harmonic Distortion + Noise − %
f − Frequency − Hz
Figure 13.
10
f = 1 kHz
PO = 200 mW
VDD = 2.5 V
1
VDD = 5 V
VDD = 3.6 V
0.1
0
0.5
1
1.5 2
2.5
3
3.5
4 4.5
Figure 18.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2036D1
5
VIC − Common Mode Input Voltage − V
7
TPA2036D1
SLOS589 – OCTOBER 2008.............................................................................................................................................................................................. www.ti.com
SUPPLY RIPPLE REJECTION RATIO
vs
FREQUENCY
−30
Inputs ac-grounded
CI = 2 µF
RL = 8 Ω
Gain = 2 V/V
−50
VDD = 2. 5 V
VDD = 3.6 V
−60
−70
−80
−30
Inputs ac-grounded
CI = 2 µF
RL = 4 Ω
Gain = 2 V/V
−40
VDD = 2.5 V
−50
−60
VDD = 3.6 V
−70
−80
100
1k
VDD = 5 V
−60
−70
VDD = 3.6 V
−80
VDD = 2.5 V
−90
20
−50
VDD = 5 V
VDD = 5 V
−90
Inputs floating
RL = 8 Ω
−40
−90
20
10 k 20 k
100
1k
20
10 k 20 k
100
Figure 19.
1k
10 k 20 k
f − Frequency − Hz
f − Frequency − Hz
f − Frequency − Hz
Figure 20.
GSM POWER SUPPLY REJECTION
vs
TIME
GSM POWER SUPPLY REJECTION
vs
FREQUENCY
0
C1 − High
3.6 V
−50
C1 − Amp
512 mV
−100
VO − Output Voltage − dBV
VDD
200 mV/div
C1 − Duty
12%
VOUT
20 mV/div
0
VDD Shown in Figure 22
CI = 2 µF,
Inputs ac-grounded
Gain = 2V/V
−50
−100
−150
0
400
t − Time − 2 ms/div
800
−40
VDD = 3.6 V
VDD = 2. 5 V
−50
VDD = 5 V
−60
−70
−80
0
0.5
1
1.5
2
2.5
3
3.5 4
4.5 5
DC Common Mode Voltage − V
Figure 24.
8
2000
−50
VIC = 200 mVPP
RL = 8 Ω
Gain = 2 V/V
−55
−60
VDD = 3.6 V
−65
−70
−75
20
100
1k
f − Frequency − Hz
10 k 20 k
Figure 25.
Submit Documentation Feedback
COMMON-MODE REJECTION RATIO
vs
COMMON-MODE INPUT VOLTAGE
CMRR − Common Mode Rejection Ratio − dB
−30
COMMON-MODE REJECTION RATIO
vs
FREQUENCY
CMRR − Common Mode Rejection Ratio − dB
Sopply Ripple Rejection Ratio − dB
−20
1600
Figure 23.
SUPPLY RIPPLE REJECTION RATIO
vs
DC COMMON MODE VOLTAGE
0
1200
f − Frequency − Hz
Figure 22.
−10
−150
V DD − Supply Voltage − dBV
−40
Sopply Ripple Rejection Ratio − dB
Sopply Ripple Rejection Ratio − dB
−30
SUPPLY RIPPLE REJECTION RATIO
vs
FREQUENCY
Sopply Ripple Rejection Ratio − dB
SUPPLY RIPPLE REJECTION RATIO
vs
FREQUENCY
0
−10
−20
−30
−40
VDD = 3.6 V
VDD = 2.5 V
−50
−60
−70
−80
VDD = 5 V,
Gain = 2
−90
−100
0
1
2
3
4
5
VIC − Common Mode Input Voltage − V
Figure 26.
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2036D1
TPA2036D1
www.ti.com.............................................................................................................................................................................................. SLOS589 – OCTOBER 2008
APPLICATION INFORMATION
FULLY DIFFERENTIAL AMPLIFIER
The TPA2036D1 is a fully differential amplifier with differential inputs and outputs. The fully differential amplifier
consists of a differential amplifier and a common-mode amplifier. The differential amplifier ensures that the
amplifier outputs a differential voltage on the output that is equal to the differential input times the gain. The
common-mode feedback ensures that the common-mode voltage at the output is biased around VDD/2 regardless
of the common-mode voltage at the input. The fully differential TPA2036D1 can still be used with a single-ended
input; however, the TPA2036D1 should be used with differential inputs when in a noisy environment, like a
wireless handset, to ensure maximum noise rejection.
Advantages of Fully Differential Amplifiers
• Input-coupling capacitors not required:
– The fully differential amplifier allows the inputs to be biased at voltage other than mid-supply. For example,
if a codec has a midsupply lower than the midsupply of the TPA2036D1, the common-mode feedback
circuit will adjust, and the TPA2036D1 outputs will still be biased at midsupply of the TPA2036D1. The
inputs of the TPA2036D1 can be biased from 0.5 V to VDD –0.8 V. If the inputs are biased outside of that
range, input-coupling capacitors are required.
• Midsupply bypass capacitor, C(BYPASS), not required:
– The fully differential amplifier does not require a bypass capacitor. This is because any shift in the
midsupply affects both positive and negative channels equally and cancels at the differential output.
• Better RF-immunity:
– GSM handsets save power by turning on and shutting off the RF transmitter at a rate of 217 Hz. The
transmitted signal is picked-up on input and output traces. The fully differential amplifier cancels the signal
much better than the typical audio amplifier.
SHORT CIRCUIT AUTO-RECOVERY
When a short circuit event happens, the TPA2036D1 goes to shutdown mode and tries to reactivate itself after
40 µs. This auto-recovery will continue until the short circuit event is removed. With the recommended PCB
layout, this feature can protect the device without affecting the device's long term reliability.
SHUTDOWN BEHAVIOR
The input of TPA2036D1 has ESD protection circuitry. During shutdown, the maximum allowed voltage at input
and output pins is -0.3 V to VDD +0.3 V.
COMPONENT SELECTION
Figure 27 shows the TPA2036D1 typical schematic with differential inputs and Figure 28 shows the TPA2036D1
with differential inputs and input capacitors, and Figure 29 shows the TPA2036D1 with single-ended inputs.
Differential inputs should be used whenever possible because the single-ended inputs are much more
susceptible to noise. X5R or X7R with ±10% or better dielectric material is required.
Table 1. Typical Component Values
(1)
REF DES
VALUE
EIA SIZE
MANUFACTURER
PART NUMBER
RI
150 kΩ (±1%)
0402
Panasonic
ERJ-2RKF1503X
CS
1 µF (X5R, ±10%)
0402
Murata
GRM155R61A105KE
15D
CI (1)
3.3 nF (X5R, ±10%)
0201
Murata
GRM033R61A332KA
01D
CI is only needed for single-ended input or if VICM is not between 0.5 V and VDD – 0.8 V. CI = 3.3 nF
(with RI = 150 kΩ) gives a high-pass corner frequency of 321 Hz.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2036D1
9
TPA2036D1
SLOS589 – OCTOBER 2008.............................................................................................................................................................................................. www.ti.com
Input Resistors I)
The input resistors I) set the gain of the amplifier according to Equation 1.
V
Gain + 2 x 150 kW
R
V
I
ǒǓ
(1)
Resistor matching is very important in fully differential amplifiers. The balance of the output on the reference
voltage depends on matched ratios of the resistors. CMRR, PSRR, and cancellation of the second harmonic
distortion diminish if resistor mismatch occurs. Therefore, it is recommended to use 1% tolerance resistors or
better to keep the performance optimized. Matching is more important than overall tolerance. Resistor arrays with
1% matching can be used with a tolerance greater than 1%.
Place the input resistors very close to the input of TPA2036D1 to limit noise injection on the high-impedance
nodes.
For optimal performance the gain should be set to 2 V/V or lower. Lower gain allows the TPA2036D1 to operate
at its best, and keeps a high voltage at the input making the inputs less susceptible to noise.
Decoupling Capacitor S)
The TPA2036D1 is a high-performance class-D audio amplifier that requires adequate power supply decoupling
to ensure the efficiency is high and total harmonic distortion (THD) is low. For higher frequency transients,
spikes, or digital hash on the line, a good low equivalent-series-resistance (ESR) ceramic capacitor, typically 1
µF (X5R or X7R dielectric), placed as close as possible (less than 1 mm) to the device VDD lead works best.
Placing this decoupling capacitor close to the TPA2036D1 is very important for the efficiency of the class-D
amplifier, because any resistance or inductance in the trace between the device and the capacitor can cause a
loss in efficiency. For filtering lower-frequency noise signals, a 10 µF or greater capacitor placed near the audio
power amplifier would also help, but it is not required in most applications because of the high PSRR of this
device.
Input Capacitors I)
The TPA2036D1 does not require input coupling capacitors if the design uses a differential source that is biased
from 0.5 V to VDD –0.8 V (shown in Figure 27). If the input signal is not biased within the recommended
common-mode input range, if needing to use the input as a high pass filter (shown in Figure 28), or if using a
single-ended source (shown in Figure 29), input coupling capacitors are required.
The input capacitors and input resistors form a high-pass filter with the corner frequency, fc, determined in
Equation 2.
1
fc +
2p R C
I I
(2)
ǒ
Ǔ
The value of the input capacitor is important to consider as it directly affects the bass (low frequency)
performance of the circuit. Speakers in wireless phones cannot usually respond well to low frequencies, so the
corner frequency can be set to block low frequencies in this application.
Equation 3 is reconfigured to solve for the input coupling capacitance.
1
C +
I
2p R f c
I
ǒ
Ǔ
(3)
If the corner frequency is within the audio band, the capacitors should have a tolerance of ±10% or better,
because any mismatch in capacitance causes an impedance mismatch at the corner frequency and below.
For a flat low-frequency response, use large input coupling capacitors (1 µF). In a GSM phone application, there
is a possibility of the 217 Hz "camping" signal being summed into the audio signal. This signal can be minimized
by reducing the RF impedance of the power supply connection through good grounding technique and
decoupling. Keeping the inputs trace length of TPA2036D1 balanced will also minimize the GSM noise both in
the RF and audio domain.
10
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2036D1
TPA2036D1
www.ti.com.............................................................................................................................................................................................. SLOS589 – OCTOBER 2008
To Battery
Internal
Oscillator
+
RI
INPWM
_
Differential
Input
-
RI
VDD
CS
VO+
HBridge
VO-
+
IN+
GND
Bias
Circuitry
SHUTDOWN
TPA2036D1
Filter-Free Class D
Figure 27. Typical TPA2036D1 Application Schematic With Differential Input for a Wireless Phone
CI
Differential
Input
RI
RI
VDD
IN_
CI
To Battery
Internal
Oscillator
PWM
HBridge
CS
VO+
VO-
+
IN+
GND
SHUTDOWN
Bias
Circuitry
TPA2036D1
Filter-Free Class D
Figure 28. TPA2036D1 Application Schematic With Differential Input and Input Capacitors
TPA2036D1
Figure 29. TPA2036D1 Application Schematic With Single-Ended Input
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2036D1
11
TPA2036D1
SLOS589 – OCTOBER 2008.............................................................................................................................................................................................. www.ti.com
SUMMING INPUT SIGNALS WITH THE TPA2036D1
Most wireless phones or PDAs need to sum signals at the audio power amplifier or just have two signal sources
that need separate gain. The TPA2036D1 makes it easy to sum signals or use separate signal sources with
different gains. Many phones now use the same speaker for the earpiece and ringer, where the wireless phone
would require a much lower gain for the phone earpiece than for the ringer. PDAs and phones that have stereo
headphones require summing of the right and left channels to output the stereo signal to the mono speaker.
Summing Two Differential Input Signals
Two extra resistors are needed for summing differential signals (a total of 5 components). The gain for each input
source can be set independently (see Equation 4 and Equation 5, and Figure 30).
V
V
Gain 1 + O + 2 x 150 kW
V
R
V
I1
I1
(4)
V
V
Gain 2 + O + 2 x 150 kW
V
R
V
I2
I2
(5)
ǒǓ
ǒǓ
If summing left and right inputs with a gain of 1 V/V, use RI1 = RI2 = 300 kΩ.
If summing a ring tone and a phone signal, set the ring-tone gain to Gain 2 = 2 V/V, and the phone gain to gain 1
= 0.1 V/V. The resistor values would be. . .
RI1 = 3 MΩ, and = RI2 = 150 kΩ.
Differential
Input 1
+
RI1
-
RI1
+
RI2
To Battery
Internal
Oscillator
Differential
Input 2
RI2
CS
IN_
-
VDD
PWM
HBridge
VO+
VO-
+
IN+
GND
SHUTDOWN
Bias
Circuitry
Filter-Free Class D
Figure 30. Application Schematic With TPA2036D1 Summing Two Differential Inputs
Summing a Differential Input Signal and a Single-Ended Input Signal
Figure 31 shows how to sum a differential input signal and a single-ended input signal. Ground noise can couple
in through IN+ with this method. It is better to use differential inputs. The corner frequency of the single-ended
input is set by CI2, shown in Equation 8. To assure that each input is balanced, the single-ended input must be
driven by a low-impedance source even if the input is not in use.
12
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2036D1
TPA2036D1
www.ti.com.............................................................................................................................................................................................. SLOS589 – OCTOBER 2008
V
Gain 1 +
V
V
Gain 2 +
C
I2
+
V
O + 2 x 150 kW
R
I1
I1
ǒVVǓ
O + 2 x 150 kW
R
I2
I2
1
ǒVVǓ
(6)
(7)
ǒ2p RI2 f c2Ǔ
(8)
If summing a ring tone and a phone signal, the phone signal should use a differential input signal while the ring
tone might be limited to a single-ended signal. Phone gain is set at gain 1 = 0.1 V/V, and the ring-tone gain is set
to gain 2 = 2 V/V, the resistor values would be…
RI1 = 3 MΩ, and = RI2 = 150 kΩ.
The high pass corner frequency of the single-ended input is set by CI2. If the desired corner frequency is less
than 20 Hz...
1
C u
I2
ǒ2p 150kW 20HzǓ
(9)
C
I2
u 53 nF
(10)
RI1
Differential
Input 1
Single-Ended
Input 2
RI1
CI2 R
I2
To Battery
Internal
Oscillator
CS
IN_
RI2
VDD
PWM
HBridge
VO+
VO-
+
IN+
CI2
SHUTDOWN
GND
Bias
Circuitry
Filter-Free Class D
Figure 31. Application Schematic With TPA2036D1 Summing Differential Input and Single-Ended Input
Signals
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2036D1
13
TPA2036D1
SLOS589 – OCTOBER 2008.............................................................................................................................................................................................. www.ti.com
Summing Two Single-Ended Input Signals
Four resistors and three capacitors are needed for summing single-ended input signals. The gain and corner
frequencies (fc1 and fc2) for each input source can be set independently (see Equation 11 through Equation 14,
and Figure 32). Resistor, RP, and capacitor, CP, are needed on the IN+ terminal to match the impedance on the
IN– terminal. The single-ended inputs must be driven by low impedance sources even if one of the inputs is not
outputting an ac signal.
V
V
Gain 1 + O + 2 x 150 kW
V
R
V
I1
I1
(11)
V
V
Gain 2 + O + 2 x 150 kW
V
R
V
I2
I2
(12)
1
C +
I1
ǒ2p RI1 f c1Ǔ
(13)
1
C +
I2
ǒ2p RI2 f c2Ǔ
(14)
C +C ) C
P
I1
I2
(15)
R
R
I2
R + I1
P
R ) R
I1
I2
(16)
ǒǓ
ǒǓ
ǒ
14
Ǔ
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2036D1
TPA2036D1
www.ti.com.............................................................................................................................................................................................. SLOS589 – OCTOBER 2008
Single-Ended
Input 1
Single-Ended
Input 2
CI1 R
I1
To Battery
CI2 R
I2
Internal
Oscillator
CS
IN_
RP
VDD
PWM
VO+
HBridge
VO-
+
IN+
CP
GND
SHUTDOWN
Bias
Circuitry
Filter-Free Class D
Figure 32. Application Schematic With TPA2036D1 Summing Two Single-Ended Inputs
BOARD LAYOUT
In making the pad size for the WCSP balls, it is recommended that the layout use nonsolder mask defined
(NSMD) land. With this method, the solder mask opening is made larger than the desired land area, and the
opening size is defined by the copper pad width. Figure 33 and Table 2 show the appropriate diameters for a
WCSP layout. The TPA2036D1 evaluation module (EVM) layout is shown in the next section as a layout
example.
Copper
Trace Width
Solder
Pad Width
Solder Mask
Opening
Copper Trace
Thickness
Solder Mask
Thickness
Figure 33. Land Pattern Dimensions
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2036D1
15
TPA2036D1
SLOS589 – OCTOBER 2008.............................................................................................................................................................................................. www.ti.com
Table 2. Land Pattern Dimensions
SOLDER PAD
DEFINITIONS
COPPER PAD
SOLDER MASK
OPENING
COPPER
THICKNESS
STENCIL
OPENING
STENCIL
THICKNESS
Nonsolder mask
defined (NSMD)
275 µm
(+0.0, –25 µm)
375 µm
(+0.0, –25 µm)
1 oz max (32 µm)
275 µm x 275 µm Sq.
(rounded corners)
125 µm thick
NOTES:
1. Circuit traces from NSMD defined PWB lands should be 75 µm to 100 µm wide in the exposed area inside
the solder mask opening. Wider trace widths reduce device stand off and impact reliability.
2. Recommend solder paste is Type 3 or Type 4.
3. Best reliability results are achieved when the PWB laminate glass transition temperature is above the
operating the range of the intended application.
4. For a PWB using a Ni/Au surface finish, the gold thickness should be less 0.5 µm to avoid a reduction in
thermal fatigue performance.
5. Solder mask thickness should be less than 20 µm on top of the copper circuit pattern.
6. Best solder stencil performance is achieved using laser cut stencils with electro polishing. Use of chemically
etched stencils results in inferior solder paste volume control.
7. Trace routing away from WCSP device should be balanced in X and Y directions to avoid unintentional
component movement due to solder wetting forces.
Component Location
Place all the external components very close to the TPA2036D1. The input resistors need to be very close to the
TPA2036D1 input pins so noise does not couple on the high impedance nodes between the input resistors and
the input amplifier of the TPA2036D1. Placing the decoupling capacitor, CS, close to the TPA2036D1 is
important for the efficiency of the class-D amplifier. Any resistance or inductance in the trace between the device
and the capacitor can cause a loss in efficiency.
Trace Width
Recommended trace width at the solder balls is 75 µm to 100 µm to prevent solder wicking onto wider PCB
traces. Figure 34 shows the layout of the TPA2036D1 evaluation module (EVM).
For high current pins (VDD, GND VO+, and VO–) of the TPA2036D1, use 100-µm trace widths at the solder balls
and at least 500-µm PCB traces to ensure proper performance and output power for the device.
For input pins (IN–, IN+, and SHUTDOWN) of the TPA2036D1, use 75-µm to 100-µm trace widths at the solder
balls. IN– and IN+ pins need to run side-by-side to maximize common-mode noise cancellation. Placing input
resistors, RIN, as close to the TPA2036D1 as possible is recommended.
16
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2036D1
TPA2036D1
www.ti.com.............................................................................................................................................................................................. SLOS589 – OCTOBER 2008
75 mm
100 mm
100 mm
100 mm
375 mm
(+0, -25 mm)
275 mm
(+0, -25 mm)
100 mm
Circular Solder Mask Opening
Paste Mask (Stencil)
= Copper Pad Size
75 mm
100 mm
75 mm
Figure 34. Close Up of TPA2036D1 Land Pattern From TPA2036D1 EVM
EFFICIENCY AND THERMAL INFORMATION
The maximum ambient temperature depends on the heat-sinking ability of the PCB system. The derating factor
for the YZF package is shown in the dissipation rating table. Converting this to θJA:
1
1
q
+
+
+ 128.2°CńW
JA
0.0078
Derating Factor
(17)
Given θJA of 128.2°C/W, the maximum allowable junction temperature of 150°C, and the maximum internal
dissipation of 0.4 W (2.25 W, 4-Ω load, 5-V supply, from Figure 3), the maximum ambient temperature can be
calculated with the following equation.
T Max + T Max * q P
+ 150 * 128.2 (0.4) + 98.72°C
A
J
JA Dmax
(18)
Equation 18 shows that the calculated maximum ambient temperature is 98.72°C at maximum power dissipation
with a 5-V supply and 4-Ω a load, see Figure 3. The TPA2036D1 is designed with thermal protection that turns
the device off when the junction temperature surpasses 165°C ~ 190°C to prevent damage to the IC. Also, using
speakers more resistive than 4-Ω dramatically increases the thermal performance by reducing the output current
and increasing the efficiency of the amplifier.
ELIMINATING THE OUTPUT FILTER WITH THE TPA2036D1
This section focuses on why the user can eliminate the output filter with the TPA2036D1.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2036D1
17
TPA2036D1
SLOS589 – OCTOBER 2008.............................................................................................................................................................................................. www.ti.com
Effect on Audio
The class-D amplifier outputs a pulse-width modulated (PWM) square wave, which is the sum of the switching
waveform and the amplified input audio signal. The human ear acts as a band-pass filter such that only the
frequencies between approximately 20 Hz and 20 kHz are passed. The switching frequency components are
much greater than 20 kHz, so the only signal heard is the amplified input audio signal.
Traditional Class-D Modulation Scheme
The traditional class-D modulation scheme, which is used in the TPA005Dxx family, has a differential output
where each output is 180 degrees out of phase and changes from ground to the supply voltage, VDD. Therefore,
the differential pre-filtered output varies between positive and negative VDD, where filtered 50% duty cycle yields
0 volts across the load. The traditional class-D modulation scheme with voltage and current waveforms is shown
in Figure 35. Note that even at an average of 0 volts across the load (50% duty cycle), the current to the load is
high causing a high loss and thus causing a high supply current.
OUT+
OUT+5 V
Differential Voltage
Across Load
0V
-5 V
Current
Figure 35. Traditional Class-D Modulation Scheme's Output Voltage and Current Waveforms Into an
Inductive Load With no Input
TPA2036D1 Modulation Scheme
The TPA2036D1 uses a modulation scheme that still has each output switching from 0 to the supply voltage.
However, OUT+ and OUT– are now in phase with each other with no input. The duty cycle of OUT+ is greater
than 50% and OUT– is less than 50% for positive voltages. The duty cycle of OUT+ is less than 50% and OUT–
is greater than 50% for negative voltages. The voltage across the load sits at 0 volts throughout most of the
switching period greatly reducing the switching current, which reduces any I2R losses in the load.
18
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2036D1
TPA2036D1
www.ti.com.............................................................................................................................................................................................. SLOS589 – OCTOBER 2008
OUT+
OUTDifferential
Voltage
Across
Load
Output = 0 V
+5 V
0V
-5 V
Current
OUT+
OUTDifferential
Voltage
Output > 0 V
+5 V
0V
Across
Load
-5 V
Current
Figure 36. The TPA2036D1 Output Voltage and Current Waveforms Into an Inductive Load
Efficiency: Why You Must Use a Filter With the Traditional Class-D Modulation Scheme
The main reason that the traditional class-D amplifier needs an output filter is that the switching waveform results
in maximum current flow. This causes more loss in the load, which causes lower efficiency. The ripple current is
large for the traditional modulation scheme because the ripple current is proportional to voltage multiplied by the
time at that voltage. The differential voltage swing is 2 × VDD and the time at each voltage is half the period for
the traditional modulation scheme. An ideal LC filter is needed to store the ripple current from each half cycle for
the next half cycle, while any resistance causes power dissipation. The speaker is both resistive and reactive,
whereas an LC filter is almost purely reactive.
The TPA2036D1 modulation scheme has very little loss in the load without a filter because the pulses are very
short and the change in voltage is VDD instead of 2 × VDD. As the output power increases, the pulses widen
making the ripple current larger. Ripple current could be filtered with an LC filter for increased efficiency, but for
most applications the filter is not needed.
An LC filter with a cutoff frequency less than the class-D switching frequency allows the switching current to flow
through the filter instead of the load. The filter has less resistance than the speaker that results in less power
dissipated, which increases efficiency.
Effects of Applying a Square Wave Into a Speaker
If the amplitude of a square wave is high enough and the frequency of the square wave is within the bandwidth
of the speaker, a square wave could cause the voice coil to jump out of the air gap and/or scar the voice coil. A
250-kHz switching frequency, however, is not significant because the speaker cone movement is proportional to
1/f2 for frequencies beyond the audio band. Therefore, the amount of cone movement at the switching frequency
is very small. However, damage could occur to the speaker if the voice coil is not designed to handle the
additional power. To size the speaker for added power, the ripple current dissipated in the load needs to be
calculated by subtracting the theoretical supplied power, PSUP THEORETICAL, from the actual supply power, PSUP, at
maximum output power, POUT. The switching power dissipated in the speaker is the inverse of the measured
efficiency, ηMEASURED, minus the theoretical efficiency, ηTHEORETICAL.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2036D1
19
TPA2036D1
SLOS589 – OCTOBER 2008.............................................................................................................................................................................................. www.ti.com
P
–P
(at max output power)
SUP SUP THEORETICAL
P
P
P
+ SUP – SUP THEORETICAL (at max output power)
SPKR
P
P
OUT
OUT
P
SPKR
SPKR
+P
+P
ǒ
(19)
(20)
Ǔ
1
1
*
(at max output power)
OUT h MEASURED h THEORETICAL
(21)
R
hTHEORETICAL +
R
L
(at max output power)
) 2r
L
DS(on)
(22)
The maximum efficiency of the TPA2036D1 with a 3.6 V supply and an 8-Ω load is 86% from Equation 22. Using
equation Equation 21 with the efficiency at maximum power (84%), we see that there is an additional 17 mW
dissipated in the speaker. The added power dissipated in the speaker is not an issue as long as it is taken into
account when choosing the speaker.
When to Use an Output Filter
Design the TPA2036D1 without an output filter if the traces from amplifier to speaker are short. The TPA2036D1
passed FCC and CE radiated emissions with no shielding with speaker trace wires 100 mm long or less.
Wireless handsets and PDAs are great applications for class-D without a filter.
A ferrite bead filter can often be used if the design is failing radiated emissions without an LC filter, and the
frequency sensitive circuit is greater than 1 MHz. This is good for circuits that just have to pass FCC and CE
because FCC and CE only test radiated emissions greater than 30 MHz. If choosing a ferrite bead, choose one
with high impedance at high frequencies, but very low impedance at low frequencies.
Use an LC output filter if there are low frequency (< 1 MHz) EMI sensitive circuits and/or there are long leads
from amplifier to speaker.
Figure 37 and Figure 38 show typical ferrite bead and LC output filters.
Ferrite
Chip Bead
OUTP
1 nF
Ferrite
Chip Bead
OUTN
1 nF
Figure 37. Typical Ferrite Chip Bead Filter (Chip bead example: TDK: MPZ1608S221A)
33 µH
OUTP
1 µF
33 µH
OUTN
1 µF
Figure 38. Typical LC Output Filter, Cutoff Frequency of 27 kHz
20
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2036D1
PACKAGE MATERIALS INFORMATION
www.ti.com
17-Jun-2015
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
TPA2036D1YZFR
DSBGA
YZF
9
3000
180.0
8.4
TPA2036D1YZFT
DSBGA
YZF
9
250
180.0
8.4
Pack Materials-Page 1
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
1.65
1.65
0.81
4.0
8.0
Q1
1.65
1.65
0.81
4.0
8.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
17-Jun-2015
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TPA2036D1YZFR
DSBGA
YZF
9
3000
182.0
182.0
20.0
TPA2036D1YZFT
DSBGA
YZF
9
250
182.0
182.0
20.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
Similar pages