Rohm MCR25F100 Thick film chip resistor Datasheet

Thick film chip resistors
MCR series
●
Datasheet
Features
1)Full line up from ultra small size (01005) to 2512 with jumper type.
2)High reliability metal glazed thick film.
3)ROHM resistors have obtained ISO9001/ISO/TS16949 certification.
Type code
Packaging
specifications
Quantity / Reel
Automotive
Grade
Available
Size
Part No.
●
(mm)
(inch)
MCR004
0402
01005
QLP
Paper tape(2mm Pitch)
20,000
-
MCR006
0603
0201
YLP
Paper tape(2mm Pitch)
15,000
Yes
MCR01
1005
0402
MZP
Paper tape(2mm Pitch)
10,000
Yes
MCR03
1608
0603
EZP
Paper tape(4mm Pitch)
5,000
Yes
MCR10
2012
0805
EZP
Paper tape(4mm Pitch)
5,000
Yes
MCR18
3216
1206
EZP
Paper tape(4mm Pitch)
5,000
Yes
MCR25
3225
1210
JZH
Embossed tape(4mm Pitch)
4,000
Yes
MCR50
5025
2010
JZH
Embossed tape(4mm Pitch)
4,000
Yes
MCR100
6432
2512
JZH
Embossed tape(4mm Pitch)
4,000
Yes
Part number description
M C R
Part No.
MCR
(Micro chip
resistors)
0 0 4
Size (mm [inch])
Q L P
Type code
004(0402 [01005])
006(0603 [0201])
01(1005 [0402])
03(1608 [0603])
10(2012 [0805])
18(3216 [1206])
25(3225 [1210])
50(5025 [2010])
100(6432 [2512])
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
J
1 0 0
Resistance tolerance
Nominal resistance
D (±0.5%)
F (±1%)
FX (±1%) *Only MCR03EZP
J (±5%) (Including jumper type)
Resistance code, 3 or 4 digits.
000 denotes jumper type.
Resistance
Resistance
tolerance
code
D,F : 4 digits
J
:
3 digits
EX.)
1Ω = 1R0 (±5%)
9.1Ω = 9R1 (±5%)
10Ω = 10R0 (±0.5%,±1%)
100 (±5%)
2.2MΩ = 2204 (±0.5%,± 1%)
225 (±5%)
1/6
2017.01 - Rev.M
MCR series
Datasheet
●Products list
Part No.
Type code
Rated power Limiting element
(70℃)
voltage
(W)
(V)
Temperature
coefficient
(ppm / ℃)
Resistance
tolerance
(%)
Operating
temperature range
(℃)
Resistance range
(Ω)
±300
F ( ±1% )
10≦R<100 (E24/96 series)
±250
F ( ±1% )
100≦R≦3M (E24/96 series)
+600/-100
J ( ±5% )
1.0≦R<10 (E24 series)
0.031
15
MCR004
QLP
±300
J ( ±5% )
10≦R<100 (E24 series)
±250
J ( ±5% )
100≦R≦3M (E24 series)
Jumper type ) Rmax : 50mΩMax., Imax : 0.5A
±200
D ( ±0.5% )
10≦R<1k (E24/96 series)
±100
D ( ±0.5% )
1k≦R≦1M (E24/96 series)
0.05
25
MCR006
YLP
±250
F ( ±1% )
10≦R≦10M (E24/96 series)
Jumper type ) Rmax : 50mΩMax., Imax : 2A
±100
D ( ±0.5% )
10≦R<100 (E24 series)
±50
D ( ±0.5% )
100≦R≦1M (E24 series)
±100
F ( ±1% )
10≦R≦2.2M (E24/96 series)
0.063
50
MCR01
MZP
+500/-250
J ( ±5% )
1.0≦R<10 (E24 series)
±200
J ( ±5% )
10≦R≦10M (E24 series)
Jumper type ) Rmax : 50mΩMax., Imax : 1A
±100
D ( ±0.5% )
10≦R<100 (E24/96 series)
±50
D ( ±0.5% )
100≦R≦1M (E24/96 series)
±100
FX ( ±1% )
10≦R≦10M (E24/96 series)
0.10
50
MCR03
EZP
±400
J ( ±5% )
1≦R<10
(E24 series)
±200
J ( ±5% )
10≦R≦10M (E24 series)
Jumper type ) Rmax : 50mΩMax., Imax : 1A
±100
D ( ±0.5% )
10≦R<100 (E24/96 series)
0.100
150
±50
D ( ±0.5% )
100≦R≦1M (E24/96 series)
±100
F ( ±1% )
10≦R≦2.2M (E24/96 series)
MCR10
EZP
±400
J ( ±5% )
1.0≦R<10 (E24 series)
0.125
150
±200
J ( ±5% )
10≦R≦10M (E24 series)
Jumper type ) Rmax : 50mΩMax., Imax : 2A
±100
D ( ±0.5% )
10≦R<100 (E24/96 series)
0.125
200
±50
D ( ±0.5% )
100≦R≦1M (E24/96 series)
±100
F ( ±1% )
10≦R≦2.2M (E24/96 series)
MCR18
EZP
±400
J ( ±5% )
1.0≦R<10 (E24 series)
0.25
200
±200
J ( ±5% )
10≦R≦10M (E24 series)
Jumper type ) Rmax : 50mΩMax., Imax : 2A
±100
F ( ±1% )
10≦R≦1M (E24/96 series)
500±350
J ( ±5% )
1.0≦R<2.2 (E24 series)
200
0.5 to 0.5 *1
±500
J ( ±5% )
2.2≦R<5.6 (E24 series)
MCR25
JZH
±200
J ( ±5% )
5.6≦R≦3.3M (E24 series)
Jumper type ) Rmax : 50mΩMax., Imax : 2A
±100
F ( ±1% )
10 ≦ R ≦ 180k (E24/96 series)
500±350
J ( ±5% )
1.0 ≦ R < 2.2 (E24 series)
±500
J ( ±5% )
2.2 ≦ R < 10 (E24 series)
0.5
200
MCR50
JZH
±200
J ( ±5% )
10 ≦ R ≦ 330k (E24 series)
±350
J ( ±5% ) 330k < R ≦ 560k (E24 series)
Jumper type ) Rmax : 50mΩMax., Imax : 3A
±100
F ( ±1% )
10≦R≦82k (E24/96 series)
500±350
J ( ±5% )
1.0≦R<2.2 (E24 series)
±500
J ( ±5% )
2.2≦R<10 (E24 series)
1
200
MCR100
JZH
±350
J ( ±5% )
10≦R<24
(E24 series)
±200
J ( ±5% )
24≦R≦100k (E24 series)
Jumper type ) Rmax : 50mΩMax., Imax : 4A
* Design and specifications are subject to change without notice.Carefully check the specification sheet supplied
with the product before using or ordering it.
* Rated voltage is determained from the following.
When rated voltage exceeds the limiting element voltage, the limitng element voltage shall be the rated voltage.
*
-55 ~ +125
-55 ~ +125
-55 ~ +155
-55 ~ +155
-55 ~ +155
-55 ~ +155
-55 ~ +155
-55 ~ +155
-55 ~ +155
-55 ~ +155
-55 ~ +125
Rated voltage =
* E24 : Standard products,
E96 : Custom products
*1. Rated power 1Ω~9.76Ω : 0.25W, 10Ω~9.76kΩ : 0.5W, 10kΩ~3.3MΩ : 0.33W
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
2/6
2017.01 - Rev.M
MCR series
●Chip resistor dimensions and markings
■MCR 004 /
006 / 01 / 03
■MCR 10 /
Datasheet
18 / 25 / 50 / 100
<Marking method>
There are three or four digits used for the calculation
number according to IEC code and Ris used for the
decimal point.
(Unit:mm)
Part No.
Type code
(mm)
(inch)
L
W
t
a
b
Marking
existence
MCR004
QLP
0402
01005
0.40±0.02
0.20±0.02
0.13±0.02
0.10±0.03
0.10±0.03
No
MCR006
YLP
0603
0201
0.60±0.03
0.30±0.03
0.23±0.03
0.10±0.05
0.15±0.05
No
MCR01
MZP
1005
0402
1.00±0.05
0.50±0.05
0.35±0.05
0.20±0.10
0.25 +0.05
-0.10
No
MCR03
EZP
1608
0603
1.60±0.10
0.80±0.10
0.45±0.10
0.30±0.20
0.30±0.20
Yes*
MCR10
EZP
2012
0805
2.00±0.10
1.25±0.10
0.55±0.10
0.40±0.20
0.40±0.20
Yes
MCR18
EZP
3216
1206
3.20±0.15
1.60±0.15
0.55±0.10
0.50±0.25
0.50±0.25
Yes
MCR25
JZH
3225
1210
3.20±0.15
2.50±0.15
0.55±0.10
0.50±0.25
0.50±0.25
Yes
MCR50
JZH
5025
2010
5.00±0.15
2.50±0.15
0.55±0.15
0.60±0.25
0.60±0.25
Yes
MCR100
JZH
6432
2512
6.30±0.15
3.20±0.15
0.55±0.15
0.60±0.25
0.60±0.25
Yes
Marking method of jumper type
Jumper type
MCR 004 / 006 / 01 / 25 / 50 / 100
MCR 03 / 10 / 18
Marking existence
No
Yes
*Marking method of MCR25/50/100
Blueglass over coat is used for the jumper type.
There is no marking on the jumper type.
*Marking method of MCR03
For MCR03 series resistors, the printing process restricts the marking to three digits/characters.
Consequently, 1% tolerance resistors with values from the E24 series will be marked the same as 5% resistors with the same value,
but 1% tolerance resistors with values from the E96 series will not be marked.
Examples:
MCR03EZPJ243
MCR03EZPFX2402
MCR03EZPFX2432
(5% tolerance, E24 / 24 kΩ )
(1% tolerance, E24 / 24 kΩ )
(1% tolerance, E96 / 24.3 kΩ )
Marking = 243
Marking = 243
No Marking
MCR18EZPJ243
MCR18EZPF2402
MCR18EZPF2432
(5% tolerance, E24 / 24 kΩ )
(1% tolerance, E24 / 24 kΩ )
(1% tolerance, E96 / 24.3 kΩ )
Marking = 243
Marking = 2402
Marking = 2432
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
3/6
2017.01 - Rev.M
MCR series
●
Datasheet
Land pattern example
(Unit:mm)
Dimensions
Part No.
MCR004
MCR006
MCR01
MCR03
MCR10
MCR18
MCR25
MCR50
MCR100
●
A
B
C
D
0.12
0.3
0.5
1.0
1.2
2.2
2.2
3.8
5.1
0.48
0.84
1.3
2.0
2.6
4.0
4.0
6.0
8.1
0.22
0.3
0.5
0.8
1.15
1.5
2.3
2.3
3.0
0.18
0.27
0.4
0.5
0.7
0.9
0.9
1.1
1.5
Derating curve
When the ambient temperature exceeds 70°C, power dissipation must be adjusted according to the derating curves below.
■MCR 004 / 100
■MCR 006 / 01 / 03 / 10 / 18 / 25 / 50
●
Characteristics
Test items
Guaranteed value
Resistor type
Jumper type
Resistance
Variation of resistance
with temperature
Overload
Solderability
Resistance to
soldering heat
See "Products list"
20℃
See "Products list"
Measurement: +25/-55, +25/+125℃
±(2.0%+0.1Ω)
MAX. 50mΩ
A new uniform coating of minimum of
95% of the surface being immersed and
no soldering damage.
±(1.0%+0.05Ω)
MAX. 50mΩ
No remarkable abnormality on the appearance.
±(1.0%+0.05Ω)
MAX. 50mΩ
Rapid change of
temperature
Damp heat, steady state
±(3.0%+0.1Ω)
MAX. 100mΩ
±(3.0%+0.1Ω)
MAX. 100mΩ
±(3.0%+0.1Ω)
MAX. 100mΩ
±(1.0%+0.05Ω)
MAX. 50mΩ
Endurance at 70℃
Endurance
Resistance to solvent
Bend strength of
the end face plating
Test conditions
Test voltage is the smaller one of ① or ②
①Rated voltage(current)×2.5, 2s
②Maximum overload voltage ※
Rosin-ethanol solution(25% weight)
Soldering condition: 245±5℃
Duration of immersion: 2.0±0.5s
Soldering condition: 260±5℃
Duration of immersion: 10±1s
Test temp.
-55℃~+125℃ 1000cycle(MCR01)
-55℃~+125℃ 100cycle(MCR004/006)
-55℃~+125℃ 5cycle(MCR03/10/18/25/50/100)
40℃,93%(Relative humidity)
Test time: 1,000h
Rated voltage(current),70℃±3℃
1.5h:ON-0.5h:OFF
Test time: 1,000h
125℃(MCR004/100)
155℃(MCR006/01/03/10/18/25/50)
Test time: 1,000h
23±5℃, Immersion cleaning, 5±0.5min
Solvent: 2-propanol
±(1.0%+0.05Ω)
MAX. 50mΩ
Without mechanical damage such as breaks.
※Maximum overload voltage (Test voltage)
MCR004 MCR006 MCR01 MCR03 MCR10 MCR18 MCR25 MCR50 MCR100
30V
50V
100V
100V
200V 400V 400V 400V 400V
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
4/6
-
Compliance Standard(s) : IEC60115-8
JISC 5201-8
2017.01 - Rev.M
MCR series
●
Datasheet
Tape dimensions
■Paper tape
(Unit : mm)
Part No.
Type code
W
F
MCR004
QLP
8.0±0.20
3.5±0.05 1.75±0.10 0.24±0.03 0.45±0.03
MCR006
YLP
8.0±0.20
3.5±0.05 1.75±0.10 0.38±0.03 0.68±0.03
MCR01
MZP
8.0±0.3
3.5±0.05 1.75±0.1
0.7±0.1
1.2±0.1
MCR03
EZP
8.0±0.3
3.5±0.05 1.75±0.1
1.1±0.1
1.9±0.1
MCR10
EZP
8.0±0.3
3.5±0.05 1.75±0.1
MCR18
EZP
8.0±0.3
3.5±0.05 1.75±0.1
1.65 +0.2
-0.1
+0.1
1.95
-0.05
2.4 +0.2
-0.1
+0.15
3.5
-0.05
Part No.
Type code
D0
MCR004
QLP
Φ1.5 +0.10
0
4.0±0.10
2.0±0.05
2.0±0.05 MAX0.50
MCR006
YLP
Φ1.5 +0.10
0
4.0±0.10
2.0±0.05
2.0±0.05 MAX0.50
MCR01
MZP
Φ1.5 +0.1
0
4.0±0.1
2.0±0.05
2.0±0.05 MAX1.1
MCR03
EZP
Φ1.5
+0.1
0
4.0±0.1
4.0±0.1
2.0±0.05 MAX1.1
MCR10
EZP
Φ1.5 +0.1
0
4.00.1
4.0±0.1
2.0±0.05 MAX1.1
MCR18
EZP
+0.1
Φ1.5 0
4.0±0.1
4.0±0.1
2.0±0.05 MAX1.1
Part No.
Type code
W
F
E
MCR25
JZH
8.0±0.3
MCR50
JZH
MCR100
P0
E
A0
P1
P2
T2
(Unit : mm)
■Embossed tape
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
B0
A0
B0
3.5±0.05 1.75±0.1
3.0±0.1
3.5±0.1
12.0±0.3
5.5±0.05 1.75±0.1
3.4±0.2
5.6±0.2
JZH
12.0±0.3
5.5±0.05 1.75±0.1
3.5±0.2
6.7±0.2
Part No.
Type code
W
F
E
A0
B0
MCR25
JZH
Φ1.5 +0.1
0
4.0±0.1
4.0±0.1
2.0±0.05 MAX1.1
MCR50
JZH
4.0±0.1
4.0±0.1
2.0±0.05 MAX1.1
MCR100
JZH
4.0±0.1
4.0±0.1
2.0±0.05 MAX1.1
5/6
Φ1.5 +0.1
0
+0.1
Φ1.5 0
2017.01 - Rev.M
MCR series
●
Datasheet
Reel dimensions
①MCR 004/006/01/03/10/18/25/50/100
②MCR 004/006/01/03/10/18/25
(Unit : mm)
Part No.
MCR004
MCR006
MCR01
MCR03
MCR10
MCR18
MCR25
MCR50
MCR100
Type code
QLP
YLP
MZP
EZP
EZP
EZP
JZH
JZH
JZH
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
A
Φ180
0
-1.5
B
Φ60
6/6
+1.0
0
C
9
+1.0
0
13
+1.0
0
D
Φ13±0.2
2017.01 - Rev.M
Notice
Precaution on using ROHM Products
1.
(Note 1)
If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment
,
aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life,
bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales
representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any
ROHM’s Products for Specific Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU
CHINA
CLASSⅢ
CLASSⅡb
CLASSⅢ
CLASSⅢ
CLASSⅣ
CLASSⅢ
2.
ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3.
Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below.
Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the
use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our
Products under any special or extraordinary environments or conditions (as exemplified below), your independent
verification and confirmation of product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4.
The Products are not subject to radiation-proof design.
5.
Please verify and confirm characteristics of the final or mounted products in using the Products.
6.
In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7.
De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in
the range that does not exceed the maximum junction temperature.
8.
Confirm that operation temperature is within the specified range described in the product specification.
9.
ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1.
When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2.
In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice-PAA-E
© 2015 ROHM Co., Ltd. All rights reserved.
Rev.003
Precautions Regarding Application Examples and External Circuits
1.
If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2.
You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation
1.
Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2.
Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3.
Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4.
Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label
A two-dimensional barcode printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act
Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign
trade act, please consult with ROHM in case of export.
Precaution Regarding Intellectual Property Rights
1.
All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data.
2.
ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the
Products with other articles such as components, circuits, systems or external equipment (including software).
3.
No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM
will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to
manufacture or sell products containing the Products, subject to the terms and conditions herein.
Other Precaution
1.
This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2.
The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3.
In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
4.
The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice-PAA-E
© 2015 ROHM Co., Ltd. All rights reserved.
Rev.003
Datasheet
General Precaution
1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.
ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s
representative.
3.
The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or
liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or
concerning such information.
Notice – WE
© 2015 ROHM Co., Ltd. All rights reserved.
Rev.001
Datasheet
MCR004QLPF - Web Page
Part Number
Package
Unit Quantity
Minimum Package Quantity
Packing Type
Constitution Materials List
RoHS
MCR004QLPF
20000
20000
Taping
inquiry
Yes
Similar pages