LITEON LTL-4222N-002 Through hole lamp Datasheet

Through Hole Lamp
Product Data Sheet
LTL-4222N-002
Spec No.: DS20-2011-0099
Effective Date: 06/04/2011
Revision: -
LITE-ON DCC
RELEASE
BNS-OD-FC001/A4
LITE-ON Technology Corp. / Optoelectronics
No.90,Chien 1 Road, Chung Ho, New Taipei City 23585, Taiwan, R.O.C.
Tel: 886-2-2222-6181 Fax: 886-2-2221-1948 / 886-2-2221-0660
http://www.liteon.com/opto
LITE-ON TECHNOLOGY CORPORATION.
Property of Lite-On Only
Features
* Lead (Pb) free product – RoHS compliant.
* High Intensity.
* Popular T-1 diameter package.
* Selected minimum intensities.
* General purpose leads.
* Reliable and rugged.
Package Dimensions
Part No.
LTL-4222N-002
Lens
Red
Source Color
Transparent
Hi-Eff.Red
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25mm(.010") unless otherwise noted.
3. The LED lamp original is LTL-4222N.
4. Lead spacing is measured where the leads emerge from the package.
5. Specifications are subject to change without notice.
Part
No. : LTL-4222N-002
BNS-OD-C131/A4
Page :
1
of
11
LITE-ON TECHNOLOGY CORPORATION.
Property of Lite-On Only
Absolute Maximum Ratings at TA=25°C
Parameter
Maximum Rating
Unit
100
mW
120
mA
Continuous Forward Current
30
mA
Derating Linear From 50℃
0.4
mA/℃
5
V
Power Dissipation
Peak Forward Current
(1/10 Duty Cycle, 0.1ms Pulse Width)
Reverse Voltage
Operating Temperature Range
-55℃ to + 100℃
Storage Temperature Range
-55℃ to + 100℃
Lead Soldering Temperature
[2.0mm(.08") From Body]
Part
No. : LTL-4222N-002
BNS-OD-C131/A4
260℃ for 5 Seconds Max.
Page :
2
of
11
LITE-ON TECHNOLOGY CORPORATION.
Property of Lite-On Only
Electrical / Optical Characteristics at TA=25°C
Parameter
Luminous Intensity
Symbol
Min.
Typ.
Max.
Unit
IV
8.7
29
90
mcd
2θ1/2
45
deg
Peak Emission Wavelength
λP
635
nm
Dominant Wavelength
λd
623
nm
Δλ
40
nm
Forward Voltage
VF
2.0
Reverse Current
IR
Viewing Angle
Spectral Line Half-Width
2.6
V
100
μA
Test Condition
IF = 10mA
Note 1,4
Note 2 (Fig.6)
Measurement
@Peak (Fig.1)
Note 3
IF = 20mA
VR = 5V
Note: 1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE
(Commission International De L'Eclairage) eye-response curve.
2. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity.
3. The dominant wavelength, λd is derived from the CIE chromaticity diagram and represents the single
wavelength which defines the color of the device.
4. The Iv guarantee should be added ±15%
Part
No. : LTL-4222N-002
BNS-OD-C131/A4
Page :
3
of
11
LITE-ON TECHNOLOGY CORPORATION.
Property of Lite-On Only
Typical Electrical / Optical Characteristics
(25°C Ambient
Part
No. : LTL-4222N-002
BNS-OD-C131/A4
Temperature
Unless
Otherwise
Curves
Noted)
Page :
4
of
11
LITE-ON TECHNOLOGY CORPORATION.
Property of Lite-On Only
Features
* Compatible with radial lead automatic insertion equipment.
* Most radial lead plastic lead lamps available packaged in tape and folding.
* 2.54mm (0.1") straight lead spacing available.
* Folding packaging simplifies handling and testing.
Package Dimensions
Item
Tape Feed Hole Diameter
Component Lead Pitch
Front to Rear Deflection
Feed Hole to Bottom of Component
Feed Hole to Overall Component Height
Lead Length After Component Height
Feed Hole Pitch
Lead Location
Center of Component Location
Total Tape Thickness
Feed Hole Location
Adhesive Tape Width
Adhesive Tape Position
Tape Width
Part
No. : LTL-4222N-002
BNS-OD-C131/A4
Symbol
D
F
△H
H1
H2
L
P
P1
P2
T
W0
W1
W2
W3
Specification
Minimum
Maximum
mm
inch
mm
inch
3.8
0.149
4.2
0.165
2.3
0.091
3.0
0.118
--2.0
0.078
17.5
0.688
18.5
0.728
21.7
0.854
23.2
0.913
W0
11.0
0.433
12.4
0.488
13.0
0.511
4.4
0.173
5.8
0.228
5.05
0.198
7.65
0.301
--0.90
0.035
8.5
0.334
9.75
0.384
14.5
0.571
15.5
0.610
0
0
3.0
0.118
17.5
0.689
19.0
0.748
Page :
5
of
11
LITE-ON TECHNOLOGY CORPORATION.
Property of Lite-On Only
Packing Spec
2 reel per inner carton
total 3,000pcs per inner carton
6 Inner cartons per outer carton
total 18,000 pcs per outer carton
In every shipping lot, only the last pack will be non-full packing
Part
No. : LTL-4222N-002
BNS-OD-C131/A4
Page :
6
of
11
LITE-ON TECHNOLOGY CORPORATION.
Property of Lite-On Only
Bin Table Specification
Luminous Intensity
Unit : mcd @10mA
Bin Code
Min.
Max.
N5
8.74
12.6
N4
12.6
19
N3
19
29
N2
29
40
N1
40
90
Note: Tolerance of each bin limit is ±15%
Part
No. : LTL-4222N-002
BNS-OD-C131/A4
Page :
7
of
11
LITE-ON TECHNOLOGY CORPORATION.
Property of Lite-On Only
CAUTIONS
1. Application
The LEDs described here are intended to be used for ordinary electronic equipment (such as office equipment,
communication equipment and household applications).Consult Liteon’s Sales in advance for information on
applications in which exceptional reliability is required, particularly when the failure or malfunction of the
LEDs may directly jeopardize life or health (such as in aviation, transportation, traffic control equipment,
medical and life support systems and safety devices).
2. Storage
The storage ambient for the LEDs should not exceed 30°C temperature or 70% relative humidity.
It is recommended that LEDs out of their original packaging are used within three months.
For extended storage out of their original packaging, it is recommended that the LEDs be stored in
a sealed container with appropriate desiccant or in desiccators with nitrogen ambient.
3. Cleaning
Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LEDs if necessary.
4. Lead Forming & Assembly
During lead forming, the leads should be bent at a point at least 3mm from the base of LED lens.
Do not use the base of the leadframe as a fulcrum during forming.
Lead forming must be done before soldering, at normal temperature.
During assembly on PCB, use minimum clinch force possible to avoid excessive mechanical stress.
5. Soldering
When soldering, leave a minimum of 2mm clearance from the base of the lens to the soldering
point.
Dipping the lens into the solder must be avoided.
Do not apply any external stress to the lead frame during soldering while the LED is at high temperature.
Recommended soldering conditions :
Soldering iron
Temperature
Soldering time
350°C Max.
3 sec. Max.
(one time only)
Wave soldering
Pre-heat
Pre-heat time
Solder wave
Soldering time
100°C Max.
60 sec. Max.
260°C Max.
5 sec. Max.
Note: Excessive soldering temperature and/or time might result in deformation of the LED lens or catastrophic
failure of the LED. IR reflow is not suitable process for through hole type LED lamp product.
Part
No. : LTL-4222N-002
BNS-OD-C131/A4
Page :
8
of
11
LITE-ON TECHNOLOGY CORPORATION.
Property of Lite-On Only
6. Drive Method
An LED is a current-operated device. In order to ensure intensity uniformity on multiple LEDs
connected in parallel in an application, it is recommended that a current limiting resistor be
incorporated in the drive circuit, in series with each LED as shown in Circuit A below.
Circuit model A
LED
Circuit model B
LED
(A) Recommended circuit
(B) The brightness of each LED might appear different due to the differences in the I-V characteristics
of those LEDs
7. ESD (Electrostatic Discharge)
Static Electricity or power surge will damage the LED.
Suggestions to prevent ESD damage:
 Use a conductive wrist band or anti- electrostatic glove when handling these LEDs
 All devices, equipment, and machinery must be properly grounded
 Work tables, storage racks, etc. should be properly grounded
 Use ion blower to neutralize the static charge which might have built up on surface of the LEDs
plastic lens as a result of friction between LEDs during storage and handing
ESD-damaged LEDs will exhibit abnormal characteristics such as high reverse leakage current, low
forward voltage, or “no light up” at low currents. To verify for ESD damage, check for “light up” and
Vf of the suspect LEDs at low currents.
The Vf of “good” LEDs should be >[email protected] for InGaN product and >[email protected] for AlInGaP product.
Part
No. : LTL-4222N-002
BNS-OD-C131/A4
Page :
9
of
11
LITE-ON TECHNOLOGY CORPORATION.
Property of Lite-On Only
Suggested checking list :
Training and Certification
1. Everyone working in a static-safe area is ESD-certified?
2. Training records kept and re-certification dates monitored?
Static-Safe Workstation & Work Areas
1. Static-safe workstation or work-areas have ESD signs?
2. All surfaces and objects at all static-safe workstation and within 1 ft measure less than 100V?
3. All ionizer activated, positioned towards the units?
4. Each work surface mats grounding is good?
Personnel Grounding
1. Every person (including visitors) handling ESD sensitive (ESDS) items wear wrist strap, heel strap or
conductive shoes with conductive flooring?
2. If conductive footwear used, conductive flooring also present where operator stand or walk?
3. Garments, hairs or anything closer than 1 ft to ESD items measure less than 100V*?
4. Every wrist strap or heel strap/conductive shoes checked daily and result recorded for all DLs?
5. All wrist strap or heel strap checkers calibration up to date?
Note: *50V for Blue LED.
Device Handling
1. Every ESDS items identified by EIA-471 labels on item or packaging?
2. All ESDS items completely inside properly closed static-shielding containers when not at static-safe
workstation?
3. No static charge generators (e.g. plastics) inside shielding containers with ESDS items?
4. All flexible conductive and dissipative package materials inspected before reuse or recycle?
Others
1. Audit result reported to entity ESD control coordinator?
2. Corrective action from previous audits completed?
3. Are audit records complete and on file?
Part
No. : LTL-4222N-002
BNS-OD-C131/A4
Page :
10
of
11
LITE-ON TECHNOLOGY CORPORATION.
Property of Lite-On Only
8. Reliability Test
Classification
Test
Item
Condition
Reference
Standard
Ta= Under Room Temperature As
Per Data Sheet Maximum Rating
*Test Time= 1000HRS (-24HRS,+72HRS)
MIL-STD-750D:1026 (1995)
MIL-STD-883D:1005 (1991)
JIS C 7021:B-1 (1982)
High Temperature
High Humidity
Storage
Ta= 65±5°C
RH= 90 ~ 95%
MIL-STD-202F: 103B(1980)
JIS C 7021 : B-11(1982)
High Temperature
Storage
Ta= 105±5°C
*Test Time= 1000HRS (-24HRS,+72HRS)
MIL-STD-883D:1008 (1991)
JIS C 7021:B-10 (1982)
Low Temperature
Storage
Ta= -55±5°C
*Test Time=1000HRS (-24HRS,+72HRS)
JIS C 7021:B-12 (1982)
Temperature
Cycling
105°C ~ 25°C ~ -55°C ~ 25°C
30mins
5mins
30mins 5mins
10 Cycles
MIL-STD-202F:107D (1980)
MIL-STD-750D:1051(1995)
MIL-STD-883D:1010 (1991)
JIS C 7021: A-4(1982)
Thermal
Shock
105 ± 5°C ~ -55°C ± 5°C
10mins
10mins
10 Cycles
MIL-STD-202F:107D(1980)
MIL-STD-750D:1051(1995)
MIL-STD-883D:1011 (1991)
Solder
Resistance
T. sol = 260 °C Max.
Dwell Time= 5secs Max.
MIL-STD-202F:210A(1980)
MIL-STD-750D:2031(1995)
JIS C 7021: A-1(1982)
Solderability
T. sol = 230 ± 5°C
Dwell Time= 5 ± 1secs
MIL-STD-202F:208D(1980)
MIL-STD-750D:2026(1995)
MIL-STD-883D:2003(1991)
JIS C 7021: A-2(1982)
Operation Life
Endurance
Test
Test
Environmental
Test
Test Time= 240HRS±2HRS
9. Others
White LED is materialized by combining blue LED and phosphors. Color of White LED is changed a little
by an operating current. The appearance and specifications of the product may be modified for improvement,
without prior notice.
Part
No. : LTL-4222N-002
BNS-OD-C131/A4
Page :
11
of
11
Similar pages