TI1 INA2143UE4 Difference amplifier Datasheet

®
INA
INA143
INA2143
214
3
INA
143
For most current data sheet and other product
information, visit www.burr-brown.com
High-Speed, Precision, G = 10 or G = 0.1
DIFFERENCE AMPLIFIERS
FEATURES
APPLICATIONS
● DESIGNED FOR LOW COST
● G = 10V/V or G = 0.1V/V
● DIFFERENTIAL INPUT AMPLIFIER
BUILDING BLOCK
● DIFF IN/DIFF OUT AMPLIFIER
● SINGLE, DUAL VERSIONS
● LOW OFFSET VOLTAGE:
±250µV max, ±3µV/°C max
● GAIN = –10 INVERTING AMPLIFIER
● GAIN = +10 NON-INVERTING AMPLIFIER
● LOW GAIN ERROR: 0.01%
● HIGH SLEW RATE: 5V/µs
● GAIN = +11 NON-INVERTING AMPLIFIER
● SYNCHRONOUS DEMODULATOR
● FAST SETTLING TIME: 9µs to 0.01%
● LOW QUIESCENT CURRENT: 950µA
● CURRENT/DIFFERENTIAL LINE RECEIVER
● VOLTAGE-CONTROLLED CURRENT SOURCE
● WIDE SUPPLY RANGE: ±2.25V to ±18V
● SO-8 and SO-14 PACKAGES
● BATTERY POWERED SYSTEMS
● LOW COST AUTOMOTIVE
DESCRIPTION
The differential amplifier is the foundation of many
commonly used circuits. The low cost INA143 and
INA2143 provide this precision circuit function without
using an expensive precision network.
The INA143 and INA2143 are high slew rate, gain of
10V/V or 0.1V/V difference amplifiers consisting of a
precision op amp with a precision resistor network. The
on-chip resistors are laser trimmed for accurate gain and
high common-mode rejection. Excellent TCR tracking
of the resistor maintains gain accuracy and commonmode rejection over temperature. They operate over a
wide supply range, ±2.25V to ±18V (+4.5V to +36V
single supply), and input common-mode voltage range
extends beyond the positive and negative supply rails.
The single version, INA143, package is the SO-8 surface
mount. The dual version, INA2143, package is the SO-14
surface mount. Both are specified for operation over the
extended industrial temperature range, –40°C to +85°C.
Operation is from –55°C to +125°C.
V+
11
–In A
2
10kΩ
100kΩ
12
Sense A
V+
–In
2
10kΩ
100kΩ
5
6
+In
3
10kΩ
13
A
7
100kΩ
1
Sense
+In A
–In B
Output
3
6
10kΩ
100kΩ
10kΩ
100kΩ
INA143
4
+In B
5
10kΩ
100kΩ
V–
10
9
B
Ref
14
8
Out A
Ref A
Sense B
Out B
Ref B
INA2143
4
V–
International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111
Twx: 910-952-1111 • Internet: http://www.burr-brown.com/ • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132
©1999 Burr-Brown Corporation
SBOS116
PDS-1531A
Printed in U.S.A. June, 1999
SPECIFICATIONS: VS = ±15V
At TA = +25°C, VS = ±15V, G = 10, RL = 10kΩ connected to ground, and reference pin connected to ground, unless otherwise noted.
INA143U
INA2143U
PARAMETER
CONDITIONS
OFFSET VOLTAGE(1)
Initial(1)
vs Temperature
vs Power Supply
vs Time
Channel Separation (dual)
MIN
RTI
VCM = 0V
VS = ±2.25V to ±18V
dc
INPUT IMPEDANCE(3)
Differential
Common-Mode
TYP
MAX
±100
±1
±5
0.2
140
±250
±3
±20
MIN
20
55
INPUT VOLTAGE RANGE
Common-Mode Voltage Range
Positive
Negative
Common-Mode Rejection Ratio
TYP
MAX
UNITS
✻
±500
See Typical Curve
✻
±30
✻
µV
µV/°C
µV/V
µV/√mo
dB
✻
✻
kΩ
kΩ
✻
✻
✻
V
V
dB
✻
✻
✻
✻
µVp-p
nV/√Hz
nV/√Hz
nV/√Hz
RTI
VCM
✻
✻
80
VO = 0V
1.1[(V+)– 1.5] 1.1[(V+) –1]
1.1[(V–) +1.5] 1.1[(V–) + 1]
VO = 0V
= –14.85V to 14.85V, RS = 0Ω
86
96
OUTPUT VOLTAGE NOISE(3)
f = 0.1Hz to 10Hz
f = 10Hz
f = 100Hz
f = 1kHz
RTI
1
45
30
27
GAIN
Initial
Error
vs Temperature
Nonlinearity
10
±0.01
±1
±0.0001
VO = –14V to +13.5V
VO = –14V to +13.5V
OUTPUT
Voltage Output
Positive
Negative
Positive
Negative
Current Limit
Capacitive Load (stable operation)
FREQUENCY RESPONSE
Small-Signal Bandwidth
Slew Rate
Settling Time: 0.1%
0.01%
Overload Recovery Time
Gain Error < 0.1%
RL = 10kΩ to Ground
RL = 10kΩ to Ground
R L = 100kΩ to Ground
R L = 100kΩ to Ground
Continuous-to-Common
(V+) –1.5
(V–) +1
–3dB
VO = 10V Step, CL = 100pF
VO = 10V Step, CL = 100pF
50% Overdrive
POWER SUPPLY
Rated Voltage
Operating Voltage Range
Dual Supplies
Single Supply
Quiescent Current (per amplifier)
TEMPERATURE RANGE
Specification
Operation
Storage
Thermal Resistance
SO-8 Surface Mount
SO-14 Surface Mount
INA143UA
INA2143UA
✻
✻
±0.1
✻
±0.002
V/V
%
ppm/°C
% of FS
✻
✻
✻
✻
✻
✻
V
V
V
V
mA
pF
0.15
5
6
9
6
✻
✻
✻
✻
✻
MHz
V/µs
µs
µs
µs
±15
✻
V
(V+) –1.3
(V–) +0.8
(V+) –0.8
(V–) +0.3
–25, +32
1000
±2.25
+4.5
±0.95
IO = 0
✻
✻
✻
✻
±0.05
±10
±0.001
–40
–55
–55
±18
+36
±1.2
✻
✻
+85
+125
+125
✻
✻
✻
✻
θJA
150
100
✻
✻
✻
✻
✻
V
V
mA
✻
✻
✻
°C
°C
°C
°C/W
°C/W
✻ Specifications the same as INA143U, INA2143U.
NOTES: (1) Includes the effects of amplifier’s input bias and offset currents. (2) Internal resistors are ratio matched but have ±20% absolute value. (3) Includes
effects of amplifier’s input current noise and thermal noise contribution of resistor network.
The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes
no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change
without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant
any BURR-BROWN product for use in life support devices and/or systems.
®
INA143, INA2143
2
SPECIFICATIONS: VS = ±5V
At TA = +25°C, VS = ±5V, G = 10, RL = 10kΩ connected to ground, and reference pin connected to ground, unless otherwise noted.
INA143U
INA2143U
PARAMETER
CONDITIONS
OFFSET VOLTAGE(1)
Initial(1)
vs Temperature
MIN
RTI
VCM = 0V
INPUT VOLTAGE RANGE
Common-Mode Voltage Range
Positive
Negative
Common-Mode Rejection Ratio
INA143UA
INA2143UA
TYP
MAX
±200
±1
±500
MIN
TYP
MAX
UNITS
✻
✻
±750
µV
µV/°C
RTI
✻
✻
80
VO = 0V
1.1[(V+)– 1.5] 1.1[(V+) –1]
1.1[(V–) +1.5] 1.1[(V–) +1]
VO = 0V
VCM = –3.85V to +3.85V, RS = 0Ω
86
96
GAIN
Initial
Gain Error
Nonlinearity
10
±0.01
±0.0001
VO = –4V to +3.5V
VO = –4V to +3.5V
OUTPUT
Voltage Output
Positive
Negative
Positive
Negative
Gain Error < 0.1%
RL = 10kΩ to Ground
RL = 10kΩ to Ground
R L = 100kΩ to Ground
R L = 100kΩ to Ground
POWER SUPPLY
Rated Voltage
Operating Voltage Range
Dual Supplies
Single Supply
Quiescent Current (per amplifier)
(V+) –1.5
(V–) +1
✻
✻
✻
±0.05
±0.001
✻
✻
(V+)–1.3
(V–)+0.8
(V+)–0.8
(V–)+0.3
+5
±2.25
+4.5
±0.92
IO = 0
✻
✻
✻
±18
+36
±1.2
V
V
dB
±0.1
±0.002
V/V
%
% of FS
✻
✻
✻
✻
V
V
V
V
✻
V
✻
✻
✻
✻
✻
✻
V
V
mA
✻ Specifications the same as INA143U, INA2143U.
NOTES: (1) Includes the effects of amplifier’s input bias and offset currents.
ABSOLUTE MAXIMUM RATINGS(1)
ELECTROSTATIC
DISCHARGE SENSITIVITY
Supply Voltage, V+ to V– .................................................................... 36V
Input Signal (G = 10), Voltage ..................................................... 1.1 • VS
Current ........................................................ 0.5mA
Input Signal (G = 0.1), Voltage ..................................................... 11 • VS
Current ....................................................... 0.5mA
Output Short-Circuit (to ground)(2) .......................................... Continuous
Operating Temperature .................................................. –55°C to +125°C
Storage Temperature ..................................................... –55°C to +125°C
Junction Temperature .................................................................... +150°C
Lead Temperature (soldering, 10s) ............................................... +300°C
This integrated circuit can be damaged by ESD. Burr-Brown
recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and
installation procedures can cause damage.
ESD damage can range from subtle performance degradation
to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric
changes could cause the device not to meet its published
specifications.
NOTES: (1) Stresses above these ratings may cause permanent damage.
Exposure to absolute maximum conditions for extended periods may degrade
device reliability. (2) One channel per package.
PACKAGE/ORDERING INFORMATION
PRODUCT
Single
INA143U
"
INA143UA
"
Dual
INA2143U
"
INA2143UA
"
PACKAGE
PACKAGE
DRAWING
NUMBER(1)
SPECIFIED
TEMPERATURE
RANGE
PACKAGE
MARKING
ORDERING
NUMBER(2)
TRANSPORT
MEDIA
SO-8 Surface Mount
182
–40°C to +85°C
INA143U
"
"
"
"
SO-8 Surface Mount
182
–40°C to +85°C
INA143UA
"
"
"
"
INA143U
INA143U/2K5
INA143UA
INA143UA/2K5
Rails
Tape and Reel
Rails
Tape and Reel
SO-14 Surface Mount
235
–40°C to +85°C
INA2143U
"
"
"
"
SO-14 Surface Mount
235
–40°C to +85°C
INA2143UA
INA2143U
INA2143U/2K5
INA2143UA
Rails
Tape and Reel
Rails
"
"
"
"
INA2143UA/2K5
Tape and Reel
NOTES: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix C of Burr-Brown IC Data Book. (2) Models with a slash (/) are
available only in Tape and Reel in the quantities indicated (e.g., /2K5 indicates 2500 devices per reel). Ordering 2500 pieces of “INA143UA/2K5” will get a single
2500-piece Tape and Reel. For detailed Tape and Reel mechanical information, refer to Appendix B of Burr-Brown IC Data Book.
®
3
INA143, INA2143
PIN CONFIGURATIONS
Top View
SO-8
Top View
SO-14
INA2143
INA143
Ref
1
8
NC
–In
2
7
V+
+In
3
6
Output
V–
4
5
Sense
NC
1
–In A
2
14
Ref A
13
Out A
A
+In A
3
12
Sense A
V–
4
11
V+
+In B
5
10
Sense B
B
–In B
6
9
Out B
NC
7
8
Ref B
NC = No Connection
NC = No Connection
®
INA143, INA2143
4
TYPICAL PERFORMANCE CURVES
At TA = +25°C, VS = ±15V, G = 10, RL = 10kΩ connected to ground, and reference pin connected to ground, unless otherwise noted.
COMMON-MODE REJECTION vs FREQUENCY
100
0
90
Closed-Mode Rejection (dB)
Closed-Loop Gain (dB)
GAIN vs FREQUENCY
5
–5
–10
–15
80
70
60
50
VS = ±15V or ±5V
VS = ±15V or ±5V
–20
40
10k
100k
1M
100
1k
Frequency (Hz)
POWER SUPPLY REJECTION vs FREQUENCY
100k
1M
MAXIMUM OUTPUT VOLTAGE vs FREQUENCY
32
Peak-to-Peak Output Voltage (V)
120
Power Supply Rejection (dB)
10k
Frequency (Hz)
100
–PSRR
80
60
+PSRR
40
20
VS = ±15V
28
24
20
16
12
VS = ±5V
8
4
0
1
10
100
1k
10k
100k
10k
100k
1M
Frequency (Hz)
Frequency (Hz)
INPUT COMMON-MODE VOLTAGE
vs OUTPUT VOLTAGE
TOTAL HARMONIC DISTORTION+NOISE
vs FREQUENCY
20
0.1
VS = ±15V
500kHz Filter
10
5
THD+N (%)
Common-Mode Voltage (V)
15
0
–5
–10
0.01
VS = ±5V
–15
–20
0.001
–15
–10
–5
0
5
10
15
20
Output Voltage (V)
100
1k
10k
20k
Frequency (Hz)
®
5
INA143, INA2143
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°C, VS = ±15V, G = 10, RL = 10kΩ connected to ground, and reference pin connected to ground, unless otherwise noted.
0.1Hz TO 10Hz PEAK-TO-PEAK
VOLTAGE NOISE
VOLTAGE NOISE DENSITY vs FREQUENCY
0.5µV/div
Voltage Noise (nV/√Hz)
100
10
1
10
100
1k
10k
500µs/div
Frequency (Hz)
QUIESCENT CURRENT vs TEMPERATURE
SLEW RATE vs TEMPERATURE
1400
7
VS = ±15V
VS = ±5V
Per Amplifier
–SR
6
Slew Rate (V/µs)
1200
1100
1000
900
5
+SR
4
800
3
700
–75
–50
–25
0
25
50
75
100
125
–75
–50
–25
Temperature (°C)
SHORT-CIRCUIT CURRENT vs TEMPERATURE
25
50
75
100
–40°C
(V+) –5
+ISC
Output Voltage (V)
25°C
30
–ISC
25
+ISC
20
125
OUTPUT VOLTAGE SWING vs OUTPUT CURRENT
V+
VS = ±15V
VS = ±5V
35
0
Temperature (°C)
40
Short-Circuit |mA|
Quiescent Current (µA)
1300
(V+) –10
85°C
0
85°C
25°C
(V–) +10
(V–) +5
–40°C
–ISC
15
(V–)
–75
–50
–25
0
25
50
75
100
0
125
®
INA143, INA2143
±5
±10
±15
±20
Output Current (mA)
Temperature (°C)
6
±25
±30
±35
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°C, VS = ±15V, G = 10, RL = 10kΩ connected to ground, and reference pin connected to ground, unless otherwise noted.
OFFSET VOLTAGE PRODUCTION DISTRIBUTION
VS = ±15V
30
20
Typical production
distribution of
packaged units.
Singles and duals
included.
20
Typical production
distribution of
packaged units.
Singles and duals
included.
18
16
Percent of Units (%)
25
Percent of Units (%)
OFFSET VOLTAGE PRODUCTION DISTRIBUTION
VS = ±5V
15
10
14
12
10
8
6
4
5
2
0
OFFSET VOLTAGE DRIFT
PRODUCTION DISTRIBUTION
VS = ±5V
60
30
20
40
0
0
2
2.5
3
3.5
4
4.5
5
5.5
700
600
20
10
1.5
500
30
10
1
Typical production
distribution of
packaged units.
Singles and duals
included.
50
Percent of Units (%)
40
0.5
400
OFFSET VOLTAGE DRIFT
PRODUCTION DISTRIBUTION
VS = ±15V
Typical production
distribution of
packaged units.
Singles and duals
included.
0
300
200
0
100
–100
–200
–300
Offset Voltage (µV)
50
0
6
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
Offset Voltage Drift (µV/°C)
Offset Voltage Drift (µV/°C)
CHANNEL SEPARATION vs FREQUENCY
SETTLING TIME vs CAPACITIVE LOAD
150
20
G = 10
G = 0.1
Channel Separation (dB)
0.01%, VS = ±15V
15
Settling Time (µs)
–400
–500
–600
Offset Voltage (µV)
60
Percent of Units (%)
–700
–500
–450
–400
–350
–300
–250
–200
–150
–100
–50
0
50
100
150
200
250
300
350
400
450
500
0
0.01%, VS = ±15V
0.01%, VS = ±5V
10
5
140
130
120
0.1%, VS = ±15V
INA2143
110
0
0
500
1000
100
1500
1k
10k
100k
Frequency (Hz)
Capacitive Load (pF)
®
7
INA143, INA2143
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°C, VS = ±15V, G = 10, RL = 10kΩ connected to ground, and reference pin connected to ground, unless otherwise noted.
LARGE-SIGNAL STEP RESPONSE
SMALL-SIGNAL STEP RESPONSE
CL = 100pF
5V/div
100mV/div
CL = 500pF
CL = 1500pF
25µs/div
2.5µs/div
®
INA143, INA2143
8
APPLICATIONS INFORMATION
throughout the full operating voltage range. Parameters which
vary significantly with operating voltage are shown in the
Typical Performance Curves.
The INA143 and INA2143 are high-speed difference amplifiers suitable for a wide range of general-purpose applications. Figure 1 shows the basic G = 10 configuration. The
input and feedback resistors can be reversed to achieve
G = 0.1, as shown in Figure 2. For applications requiring
G = 1, the INA133 and INA2133 are recommended.
OFFSET VOLTAGE TRIM
The INA143 and INA2143 are laser trimmed for low offset
voltage and drift. Most applications require no external offset
adjustment. Figure 3 shows an optional circuit for trimming
the output offset voltage. The output is referred to the output
reference terminal (pin 1), which is normally grounded. A
voltage applied to the Ref terminal will be summed with the
output signal. This can be used to null offset voltage as
shown in Figure 3. The source impedance of a signal applied
to the Ref terminal should be less than 10Ω to maintain good
common-mode rejection.
Decoupling capacitors are strongly recommended for applications with noisy or high impedance power supplies. The
capacitors should be placed close to the device pins as
shown in Figure 1. All circuitry is completely independent
in the dual version assuring lowest crosstalk and normal
behavior when one amplifier is overdriven or short-circuited.
As shown in Figure 1, the differential input signal is connected to pins 2 and 3. The source impedances connected to
the inputs must be nearly equal to assure good commonmode rejection. A 5Ω mismatch in source impedance will
degrade the common-mode rejection of a typical device to
approximately 86dB (RTI). If the source has a known
impedance mismatch, an additional resistor in series with
the opposite input can be used to preserve good commonmode rejection.
INA143
–In
V2
5
R1
10kΩ
R2
100kΩ
2
6
The INA143’s internal resistors are accurately ratio trimmed
to match. That is, R1/R2 and R3/R4 are trimmed to equal 0.1.
However, the absolute values may not be equal (R1 + R2 may
be slightly different than R3 + R4). Thus, large series resistors
on the input (greater than 100Ω), even if well matched, will
degrade common-mode rejection.
VO = 0.1 (V3 – V2)
+In
1
V3
R3
10kΩ
R4
100kΩ
3
FIGURE 2. G = 0.1 Difference Amplifier.
V+
V–
1µF
1µF
G = 10
7
4
INA143
INA143
–In
V2
2
R1
10kΩ
R2
100kΩ
2
V2
5
R2
100kΩ
R1
10kΩ
5
6
VO
6
VO = 10 (V3 – V2)
+In
V3
3
R3
10kΩ
R4
100kΩ
10Ω
V3
3
R3
10kΩ
1
Compensates
for impedance at
pin 1—see text.
R4
100kΩ
+15V
1
499kΩ
FIGURE 1. G = 10 Basic Power Supply and Signal Connections.
100kΩ
VO = 10 (V3 – V2)
Offset Adjustment
Range = ±3mV
OPERATING VOLTAGE
The INA143 and INA2143 operate from single (+4.5V to
+36V) or dual (±2.25V to ±18V) supplies with excellent
performance. Specifications are production tested with ±5V
and ±15V supplies. Most behavior remains unchanged
100Ω
–15V
FIGURE 3. Offset Adjustment.
®
9
INA143, INA2143
INA143
V1
–In
10Ω
V1
10kΩ
2
100kΩ
5
200Ω
A1
Gain
Adjust
INA143
2
R2
10kΩ
100kΩ
5
VO
6
6
R1
VO
R2
10Ω
V2
10kΩ
3
100kΩ
1
200Ω
3
CMR
Adjust
A2
To eliminate adjustment interactions,
first adjust gain with V2 grounded.
10kΩ
100kΩ
1
V0 = 10 (1 + 2R2 /R1) (V2 – V1)
V2
+In
FIGURE 4. Difference Amplifier with Gain and CMR Adjust.
The INA143 can be combined with op amps to form a complete instrumentation amplifier with specialized performance characteristics. Burr-Brown offers
many complete high performance IAs. Products with related performances
are shown at the right in the table below.
INA143
10kΩ
V2
100kΩ
2
5
6
10kΩ
VO = –10 • V2
100kΩ
3
1
A1, A2
FEATURE
SIMILAR COMPLETE
BURR-BROWN IA
OPA2227
Low Noise
INA103
OPA129
Ultra Low Bias Current (fA)
INA116
OPA2277
Low Offset Drift, Low Noise
INA114, INA128
OPA2130
Low Power, FET-Input (pA)
INA121
OPA2234
Single Supply, Precision, Low Power
INA122, INA118
OPA2237
Single Supply, Low Power, MSOP-8
INA122, INA126
FIGURE 7. Precision Instrumentation Amplifier.
Gain Error = 0.05% maximum
Nonlinearity = 0.001% maximum
Gain Drift = 1ppm/°C
INA143
R1
10kΩ
2
R2
100kΩ
5
FIGURE 5. Precision G = –10 Inverting Amplifier.
V1
1
R4
100kΩ
INA143
R1
10kΩ
2
VIN
R2
100kΩ
R4
100kΩ
1
V3
VO = V1 + 10 • V3
R3
10kΩ
3
5
6
±55V
Without
Damage
6
FIGURE 8. Precision Summing Amplifier.
VO = VIN
INA143
R3
10kΩ
2
10kΩ
100kΩ
5
3
1
VIN
This circuit follows an 11/1 divider with a gain of 11 for an overall gain of unity.
With an 11/1 divider, the input signal can exceed 55V without damage as
long as input current is less than 0.5mA.
FIGURE 6. Voltage Follower with Input Protection.
10kΩ
FIGURE 9. Precision G = 11 Buffer.
®
INA143, INA2143
3
100kΩ
10
6
VO = 11 • VIN
Gain Error =
0.05% maximum
PACKAGE OPTION ADDENDUM
www.ti.com
6-Jul-2009
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
INA143U
ACTIVE
SOIC
D
8
INA143U/2K5
ACTIVE
SOIC
D
INA143U/2K5E4
ACTIVE
SOIC
INA143UA
ACTIVE
INA143UA/2K5
75
Lead/Ball Finish
MSL Peak Temp (3)
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
SOIC
D
8
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
INA143UA/2K5E4
ACTIVE
SOIC
D
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
INA143UAG4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
INA143UG4
ACTIVE
SOIC
D
8
75
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
INA2143U
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
INA2143U/2K5E4
OBSOLETE
SOIC
D
14
TBD
Call TI
INA2143UA
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
INA2143UAE4
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
INA2143UAG4
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
INA2143UE4
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
INA2143UG4
ACTIVE
SOIC
D
14
50
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
75
Call TI
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
6-Jul-2009
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Mar-2008
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
Diameter Width
(mm) W1 (mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
INA143U/2K5
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
INA143UA/2K5
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Mar-2008
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
INA143U/2K5
SOIC
D
8
2500
346.0
346.0
29.0
INA143UA/2K5
SOIC
D
8
2500
346.0
346.0
29.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DLP® Products
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2009, Texas Instruments Incorporated
Similar pages