NSNJ2006 Jun. 2015 New JRC SAW FILTER NSNJ2006 Application Low Power Transceiver f0=465MHz BW=6MHz Electrical Specification: (Table 1) The device characteristics are measured in the circuit shown in Fig.1. Table 1. Electrical Specifications Item Input and Output Impedance Nominal Center Frequency (f0) Insertion Loss 462〜468MHz Response Variation 462〜468MHz VSWR 462〜468MHz Out of Band Rejection 419.2〜425.2MHz (Relative to 440.9〜446.9MHz Through Level) 504.8〜510.8MHz Spec. 3.5dB max. 1.5dB max. 2.0 max. 45dB min. 45dB min. 45dB min. Typ. 50 465MHz 2.9dB 0.7dB 1.6 55dB 54dB 59dB (Operating Temperature Range: -20~+60ºC) Maximum Rating: (Table 2) Table2. Maximum Ratings Item Maximum Input Power Maximum DC Voltage Operating Temperature Range Storage Temperature Rating +20dBm 7.5V -20~+60ºC -30~+85ºC Mechanical Specifications: (Fig.2) Package is designed as small as 3.0x3.0x1.15[mm3] for SMD (Surface Mount Device) type. Notice: This part is electrostatic discharge sensitive and may be damaged by improper handling. http://www.njr.co.jp/products/device/index.html （Japanese） http://www.njr.com/products/device/index.html （English） NSNJ2006 Jun. 2015 1 IN 50 6 OUT 50 2 SAW 5 3 4 Fig.1 Measuring circuit (a) ( b) 3. 0±0. 15 3. 0 ± 0. 1 5 560 ( c) RJ (1) ( 0. 6) ( 0. 2 5) 1. 1 5 ± 0. 1 5 ( 2) 4 ( 0. 6) [ 2 x] 3 2 5 ( 1. 80) 1 6 [ 4x] Pin no. ( 0. 5 3) [ 4 x] ( 0. 75) ( 0. 45) Fig.2 Package dimensions (in mm) 0.93 3.8 1.15 3.8 0.6 2.2 Marking (1) Lot Number (a) Year (b) Month *Oct.--Nov.--Dec.--(c) Date 1-9--10-19--20-31--(2) Part Number Mark 0.93 1.15 Fig.3 Desirable land area (in mm) Connection 1 GND 2 IN/OUT 3 GND 4 GND 5 OUT/IN 6 GND X Y Z 0 1 2 NSNJ2006 Jun. 2015 Notice 1. Use this component within operating temperature range. It might not be satisfied with electrical specification without operating temperature range. When it is used less than -20ºC or more than +60ºC, it might be a cause of degradation or destruction of the component. Even if it endures during a short time, it causes degradation of qualification. 2. When soldering iron is used, solder with the temperature at the tip of soldering iron: 350ºC max., the time of soldering: 10 seconds max., the power of soldering iron: 30W max.. 3. Notice that the allowed time of soldering with soldering iron is accumulated time, when soldering is repeated. 4. As rapid temperature change for cleaning after reflow soldering might be a cause of destruction clean this component after confirming that temperature of this component goes down to room temperature. 5. Confirm that there are not any influence for qualification to this component in mounting on PCB when this component is cleaned. 6. As it might be a cause of degradation of destruction to apply static electricity to this component, do not apply static electricity or excessive voltage while assembling and measuring. And do not transport this component with bare hand. 7. As it might be a cause of degradation or destruction to apply D.C. voltage between each terminal, apply D.C. voltage 7.5V max. in actual circuit. Note 1. This specification specifies the quality of this component as a single unit. Make sure that this component is evaluated and confirmed against this specification when it is mounted to your products. NSNJ2006 Jun. 2015 S21 0 1 Insertion Loss [dB] 2 3 4 5 6 7 8 9 10 Center 465[MHz] S11 Span 20[MHz] S22 Center 465[MHz] Span 100[MHz] Center 465[MHz] Span 100[MHz] S22 5 5 VSWR 6 4 3 2 4 3 2 1 Center 465[MHz] Span 20[MHz] 1 Center 465[MHz] S21 0 10 20 Insertion Loss [dB] VSWR S11 6 30 40 50 60 70 80 Center 465[MHz] Span 100[MHz] Span 20[MHz]