Maxim MAX1853 Sc70 inverting charge pumps with shutdown Datasheet

19-1792; Rev 0; 9/00
SC70 Inverting Charge Pumps
with Shutdown
Features
♦ 30mA Output Current
♦ Low 15Ω Output Resistance
♦ 68µA Supply Current (MAX1852)
♦ Requires Only Two 0.68µF Capacitors (MAX1853)
♦ +2.5V to +5.5V Input Voltage Range
♦ 0.1µA Logic-Controlled Shutdown
♦ Two Switching Frequencies
50kHz (MAX1852)
200kHz (MAX1853)
♦ Slew-Rate Limited to Reduce EMI
♦ Ultra-Small 6-Pin SC70 Package
Applications
Negative Supply from +5V or +3.3V Logic Supplies
Small LCD Panels
Ordering Information
GaAsFET Bias Supplies
MAX1852EXT
TEMP.
RANGE
-40°C to +85°C
PINPACKAGE
6 SC70
MAX1853EXT
-40°C to +85°C
6 SC70
PART
Handy-Terminals, PDAs
Battery-Operated Equipment
TOP
MARK
AAL
AAM
Pin Configuration
Typical Operating Circuit
0.68µF
TOP VIEW
INPUT
2.5V TO 5.5V
C1+
C1OUT
IN
MAX1853
SHDN
ON
OFF
NEGATIVE
OUTPUT
-1 ✕ VIN
30mA
OUT
1
GND
2
SHDN
3
6
MAX1852
MAX1853
C1+
5 C1-
0.68µF
4
IN
GND
SC70-6
________________________________________________________________ Maxim Integrated Products
1
For free samples and the latest literature, visit www.maxim-ic.com or phone 1-800-998-8800.
For small orders, phone 1-800-835-8769.
MAX1852/MAX1853
General Description
The MAX1852/MAX1853 monolithic, CMOS chargepump voltage inverters in the ultra-small SC70 package
feature a low 15Ω output resistance, permitting loads
up to 30mA with maximum efficiency. The MAX1852/
MAX1853 are available with operating frequencies of
50kHz and 200kHz, respectively, allowing optimization
of supply current or external component size. Small
external components and micropower shutdown mode
make these devices ideal for both battery-powered and
board-level voltage conversion applications.
Oscillator control circuitry and four power-MOSFET
switches are included on-chip. Applications include
generating a negative supply from a +5V or +3.3V logic
supply to power analog circuitry. Both versions come in
a 6-pin SC70 package that is 40% smaller than a
SOT23.
MAX1852/MAX1853
SC70 Inverting Charge Pumps
with Shutdown
ABSOLUTE MAXIMUM RATINGS
IN to GND .................................................................-0.3V to +6V
C1+, SHDN to GND .....................................-0.3V to (VIN + 0.3V)
C1- to GND...............................................(VOUT - 0.3V) to +0.3V
OUT to GND .............................................................+0.3V to -6V
OUT Short-Circuit to GND ..............................................1 minute
Continuous Power Dissipation (TA = +70°C)
6-Pin SC70 (derate 3.1mW/°C above +70°C) .............245mW
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(Circuit of Figure 1, capacitors from Table 2, VIN = +5V, SHDN = IN, TA = -40°C to +85°C, unless otherwise noted. Typical values are
at TA = +25°C.) (Note 1)
PARAMETER
CONDITIONS
Supply Voltage Range
Quiescent Supply Current
MAX1853
SHDN = GND
MAX1852
Oscillator Frequency
MAX1853
Voltage Conversion Efficiency
Output Resistance (Note 2)
TYP
2.5
MAX1852
Shutdown Supply Current
MIN
TA = +25°C
Output Current
Continuous, long-term
SHDN Input Logic High
+2.5V ≤ VIN ≤ +5.5V
SHDN Input Logic Low
+2.5V ≤ VIN ≤ +5.5V
SHDN Bias Current
SHDN = GND or IN
Wake-Up Time From Shutdown
IOUT = 5mA
165
TA = -40°C to +85°C
TA = +25°C
0.002
0.01
32
V
130
320
TA = -40°C to +85°C
25
TA = +25°C
130
TA = -40°C to +85°C
110
99
TA = +25°C
0.5
50
68
200
270
78
99.9
15
TA = -40°C to +85°C
40
30
TA = +85°C
kHz
Ω
mARMS
V
0.3 × VIN
-100
µA
%
30
0.7 × VIN
TA = +25°C
µA
310
1
10
MAX1852
260
MAX1853
112
Note 1: All devices are 100% production tested at TA = +25°C. All temperature limits are guaranteed by design.
Note 2: Output resistance is guaranteed with capacitor ESR of 0.3Ω or less.
2
5.5
350
TA = +85°C
TA = +25°C
UNITS
150
TA = +25°C
IOUT = 0
IOUT = 10mA
75
TA = -40°C to +85°C
MAX
_______________________________________________________________________________________
100
V
nA
µs
SC70 Inverting Charge Pumps
with Shutdown
MAX1853
OUTPUT VOLTAGE
vs. LOAD CURRENT
VIN = +3.3V
-3.5
-4.0
VIN = +5V
-3.0
90
-3.5
-4.0
VIN = +3.3V
70
VIN = +2.5V
60
50
40
30
VIN = +5V
-4.5
VIN = +5V
80
EFFICIENCY (%)
-3.0
-2.5
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
VIN = +3.3V
100
MAX1852/3 toc02
-2.5
-4.5
-2.0
MAX1852/3 toc01
-2.0
MAX1852
EFFICIENCY vs. LOAD CURRENT
MAX1852/3 toc03
MAX1852
OUTPUT VOLTAGE
vs. LOAD CURRENT
20
-5.0
-5.5
-5.5
5
10
15
20
25
5
10
15
20
25
MAX1853
EFFICIENCY vs. LOAD CURRENT
OUTPUT RESISTANCE vs. INPUT VOLTAGE
VIN = +2.5V
60
50
40
30
23
22
21
20
19
18
MAX1853
17
MAX1852
16
120
80
60
20
0
13
25
3.0
3.5
4.0
4.5
5.0
0
5.5
1
2
3
4
5
LOAD CURRENT (mA)
INPUT VOLTAGE (V)
SUPPLY VOLTAGE (V)
SHUTDOWN SUPPLY CURRENT
vs. TEMPERATURE
MAX1852
OUTPUT RESISTANCE vs. TEMPERATURE
MAX1853
OUTPUT RESISTANCE vs. TEMPERATURE
5
4
3
2
24
VIN = +2.5V
22
VIN = +3.3V
20
18
VIN = +5V
16
-15
10
35
TEMPERATURE (°C)
60
85
VIN = +2.5V
24
22
VIN = +3.3V
20
18
VIN = +5V
16
12
12
0
26
14
14
1
MAX1852/3 toc09
26
28
OUTPUT RESISTANCE (Ω)
6
MAX1852/3 toc08
7
28
OUTPUT RESISTANCE (Ω)
MAX1852/3 toc07
8
-40
MAX1852
0
2.5
30
MAX1853
100
14
20
30
140
10
15
25
160
40
10
20
180
15
5
15
200
20
0
10
NO-LOAD SUPPLY CURRENT
vs. SUPPLY VOLTAGE
SUPPLY CURRENT (µA)
VIN = +3.3V
70
5
LOAD CURRENT (mA)
MAX1852/3 toc05
MAX1852/3 toc04
VIN = +5V
80
0
30
LOAD CURRENT (mA)
90
SUPPLY CURRENT (nA)
0
0
LOAD CURRENT (mA)
100
EFFICIENCY (%)
30
OUTPUT RESISTANCE (Ω)
0
10
MAX1852/3 toc06
-5.0
-40
-15
10
35
TEMPERATURE (°C)
60
85
-40
-15
10
35
60
85
TEMPERATURE (°C)
_______________________________________________________________________________________
3
MAX1852/MAX1853
Typical Operating Characteristics
(Circuit of Figure 1, capacitors from Table 2, VIN = +5V, SHDN = IN, TA = +25°C, unless otherwise noted.)
Typical Operating Characteristics (continued)
(Circuit of Figure 1, capacitors from Table 2, VIN = +5V, SHDN = IN, TA = +25°C, unless otherwise noted.)
MAX1852
CHARGE-PUMP FREQUENCY
vs. TEMPERATURE
MAX1853
CHARGE-PUMP FREQUENCY
vs. TEMPERATURE
56
55
54
220
215
210
53
52
MAX1852/3 toc12
270
FREQUENCY (kHz)
57
225
FREQUENCY (kHz)
FREQUENCY (kHz)
58
MAX1852/3 toc11
59
CHARGE-PUMP FREQUENCY
vs. INPUT VOLTAGE
230
MAX1852/3 toc10
60
MAX1853
220
170
120
70
205
MAX1852
51
20
200
-40
-20
0
20
60
40
80
-40
-20
0
20
40
60
2.0
80
2.5
3.0
3.5
4.0
5.0
MAX1852 AND MAX1853
OUTPUT VOLTAGE vs. INPUT VOLTAGE
OUTPUT VOLTAGE RIPPLE
vs. CAPACITANCE
MAX1852
OUTPUT NOISE AND RIPPLE
-2.5
-3.0
-3.5
-4.0
-4.5
-5.0
350
OUTPUT VOLTAGE RIPPLE (mV)
ILOAD = 10mA
C1 = C2
ILOAD = 10mA
300
MAX1852/3 toc14
INPUT VOLTAGE (V)
MAX1852/3 toc13
TEMPERATURE (°C)
-2.0
5.5
C1 = C2 = 4.7µF
250
200
150
VOUT
20mV/div
MAX1852
100
MAX1853
50
-5.5
0
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
10µs/div
ILOAD = 10mA, AC-COUPLED
0.2 0.7 1.2 1.7 2.2 2.7 3.2 3.7 4.2 4.7
INPUT VOLTAGE (V)
CAPACITANCE (µF)
MAX1853
OUTPUT NOISE AND RIPPLE
MAX1853
STARTUP FROM SHUTDOWN
MAX1852
STARTUP FROM SHUTDOWN
MAX1852/3 toc18
MAX1852/3 toc16
MAX1852/3 toc17
C1 = C2 = 1µF
SHDN
SHDN
0
VOUT
20mV/div
2V/div
0
2V/div
0
0
VOUT
VOUT
2µs/div
ILOAD = 10mA, AC-COUPLED
4
4.5
TEMPERATURE (°C)
MAX1852/3 toc15
50
OUTPUT VOLTAGE (V)
MAX1852/MAX1853
SC70 Inverting Charge Pumps
with Shutdown
100µs/div
40µs/div
_______________________________________________________________________________________
SC70 Inverting Charge Pumps
with Shutdown
C1
PIN
NAME
1
OUT
2
3
FUNCTION
Inverting Charge-Pump Output
GND
Ground
SHDN
Shutdown Input. Drive this pin high
for normal operation; drive it low for
shutdown mode.
4
IN
Power-Supply Voltage Input. Input
range is +2.5V to +5.5V.
5
C1-
Negative Terminal of the Flying
Capacitor
C1+
Positive Terminal of the Flying
Capacitor
6
Detailed Description
The MAX1852/MAX1853 charge pumps invert the voltage applied to their input. For highest performance use
low equivalent series resistance (ESR) capacitors (e.g.,
ceramic).
During the first half-cycle, switches S2 and S4 open,
switches S1 and S3 close, and capacitor C1 charges to
the voltage at IN (Figure 2). During the second halfcycle, S1 and S3 open, S2 and S4 close, and C1 is level
shifted downward by VIN volts. This connects C1 in parallel with the reservoir capacitor C2. If the voltage across
C2 is smaller than the voltage across C1, charge flows
from C1 to C2 until the voltage across C2 reaches
-VIN. The actual voltage at the output is more positive
than -VIN since switches S1–S4 have resistance and the
load drains charge from C2.
Efficiency Considerations
The efficiency of the MAX1852/MAX1853 is dominated
by their quiescent supply current (IQ) at low output current and by their output impedance (ROUT) at higher
output current; it is given by:
IOUT  IOUT x ROUT 
η≅
1 −

VIN
IOUT + IQ 

where the output impedance is roughly approximated
by:
1
ROUT ≅
+ 2RSW + 4ESRC1 + ESRC2
fOSC x C1
(
)
The first term is the effective resistance of an ideal
switched-capacitor circuit (Figures 3a and 3b), and
RSW is the sum of the charge pump’s internal switch
INPUT
2.5V TO 5.5V
4
6
C1+
5
C1-
IN
OUT
C3
ON
OFF
3
RL
MAX1852
MAX1853
SHDN
NEGATIVE
OUTPUT
-1 ✕ VIN
1
C2
GND
2
TE: (
Figure 1. Typical Application Circuit
resistances (typically 6Ω at VIN = +5V). The typical output impedance is more accurately determined from the
Typical Operating Characteristics.
Shutdown
The MAX1852/MAX1853 have a logic-controlled shutdown input. Driving SHDN low places the devices in a
low-power shutdown mode. The charge-pump switching halts, supply current is reduced to 2nA.
Driving SHDN high will restart the charge pump. The
switching frequency and capacitor values determine how
soon the device will reach 90% of the input voltage.
Applications Information
Capacitor Selection
The charge-pump output resistance is a function of the
ESR of C1 and C2. To maintain the lowest output resistance, use capacitors with low ESR. (See Table 1 for a
list of recommended manufacturers.) Tables 2 and 3
suggest capacitor values for minimizing output resistance or capacitor size.
Flying Capacitor (C1)
Increasing the flying capacitor’s value reduces the output resistance. Above a certain point, increasing C1’s
capacitance has negligible effect because the output
resistance is then dominated by internal switch resistance and capacitor ESR.
Output Capacitor (C2)
Increasing the output capacitor’s value reduces the
output ripple voltage. Decreasing its ESR reduces both
output resistance and ripple. Lower capacitance values
can be used with light loads if higher output ripple can
be tolerated. Use the following equation to calculate the
peak-to-peak ripple:
_______________________________________________________________________________________
5
MAX1852/MAX1853
Pin Description
MAX1852/MAX1853
SC70 Inverting Charge Pumps
with Shutdown
S1
REQUIV
S2
IN
V+
C1
S3
VOUT
REQUIV =
1
fOSC ✕ C1
C2
RL
C2
S4
VOUT = -(VIN)
Figure 3b. Equivalent Circuit
Paralleling Devices
Figure 2. Ideal Voltage Inverter
fOSC
V+
VOUT
C1
C2
RL
Figure 3a. Switched-Capacitor Model
VRIPPLE =
IOUT
+ 2 × IOUT × ESRC2
2(fOSC )C2
Input Bypass Capacitor (C3)
If necessary, bypass the incoming supply to reduce its
AC impedance and the impact of the MAX1852/
MAX1853s’ switching noise. A bypass capacitor with a
value equal to that of C1 is recommended.
Voltage Inverter
The most common application for these devices is a
charge-pump voltage inverter (Figure 1). This application requires only two external components—capacitors
C1 and C2—plus a bypass capacitor, if necessary.
Refer to the Capacitor Selection section for suggested
capacitor types.
Paralleling multiple MAX1852/MAX1853s reduces the
output resistance. Each device requires its own pump
capacitor (C1), but the reservoir capacitor (C2) serves
all devices (Figure 5). Increase C2’s value by a factor of
n, where n is the number of parallel devices. Figure 5
shows the equation for calculating output resistance.
Combined Doubler/Inverter
In the circuit of Figure 6, capacitors C1 and C2 form the
inverter, while C3 and C4 form the doubler. C1 and C3
are the pump capacitors; C2 and C4 are the reservoir
capacitors. Because both the inverter and doubler use
part of the charge-pump circuit, loading either output
causes both outputs to decline toward GND. Make sure
the sum of the currents drawn from the two outputs
does not exceed 30mA.
Heavy Load Connected to a
Positive Supply
Under heavy loads, where a higher supply is sourcing
current into OUT, the OUT supply must not be pulled
above ground. Applications that sink heavy current into
OUT require a Schottky diode (1N5817) between GND
and OUT, with the anode connected to OUT (Figure 7).
Layout and Grounding
Good layout is important, primarily for good noise performance. To ensure good layout, mount all components as close together as possible, keep traces short
to minimize parasitic inductance and capacitance, and
use a ground plane.
Cascading Devices
Two devices can be cascaded to produce an even
larger negative voltage (Figure 4). The unloaded output
voltage is normally -2 ✕ VIN, but this is reduced slightly
by the output resistance of the first device multiplied by
the quiescent current of the second. When cascading
more than two devices, the output resistance rises significantly. For applications requiring larger negative
voltages, see the MAX865 and MAX868 data sheets.
6
_______________________________________________________________________________________
SC70 Inverting Charge Pumps
with Shutdown
PRODUCTION
METHOD
MANUFACTURER
SERIES
PHONE
FAX
Surface-Mount
Tantalum
Surface-Mount
Ceramic
AVX
TPS series
803-946-0690
803-626-3123
Matsuo
267 series
714-969-2491
714-960-6492
Sprague
593D, 595D series
603-224-1961
603-224-1430
AVX
X7R
803-946-0690
803-626-3123
Matsuo
X7R
714-969-2491
714-960-6492
Table 2. Capacitor Selection to Minimize
Output Resistance
Table 3. Capacitor Selection to Minimize
Capacitor Size
PART
FREQUENCY
(kHz)
CAPACITOR
(µF)
TYPICAL
ROUT (Ω)
PART
FREQUENCY
(kHz)
CAPACITOR
(µF)
TYPICAL
ROUT (Ω)
MAX1852
50
4.7
15
MAX1852
50
3.3
20
MAX1853
200
1
15
MAX1853
200
0.68
20
…
4
2
5
5
MAX1852
MAX1853
2
C1
6
1
MAX1852
MAX1853
C1
1
6
…
3
VOUT
2
D1, D2 = 1N4148
4
MAX1852
MAX1853
D1
6
1
VOUT = -VIN
C2
3
C2
+VIN
3
4
5
C1
SHDN
+VIN
C2
D2
SHDN
VOUT = -nVIN
Figure 4. Cascading MAX1852/MAX1853s to Increase Output
Voltage
+VIN
C1
2
C1
1
6
2
GND
2
MAX1852
MAX1853
MAX1852
MAX1853
1
6
…
3
SHDN
Figure 6. Combined Doubler and Inverter
4
5
MAX1852
MAX1853
VOUT = (2VIN) (VFD1) - (VFD2)
…
4
5
C4
C3
VOUT
V+
RL
OUT
1
3
VOUT = -VIN
C2
Figure 7. Heavy Load Connected to a Positive Supply
ROUT OF SINGLE DEVICE
ROUT = NUMBER OF DEVICES
Figure 5. Paralleling MAX1852/MAX1853s to Reduce Output
Resistance
Chip Information
TRANSISTOR COUNT: 252
_______________________________________________________________________________________
7
MAX1852/MAX1853
Table 1. Low-ESR Capacitor Manufacturers
________________________________________________________Package Information
SC70, 6L.EPS
MAX1852/MAX1853
SC70 Inverting Charge Pumps
with Shutdown
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
8 ___________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600
© 2000 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
Similar pages