ON MC74172B Quad eiaâ 485 line driver Datasheet

ON Semiconductort
MC75172B
MC75174B
Quad EIA−485 Line Drivers
with Three−State Outputs
The ON Semiconductor MC75172B/174B Quad Line drivers are
differential high speed drivers designed to comply with the EIA−485
Standard. Features include three−state outputs, thermal shutdown,
and output current limiting in both directions. These devices also
comply with EIA−422−A, and CCITT Recommendations V.11 and
X.27.
The MC75172B/174B are optimized for balanced multipoint bus
transmission at rates in excess of 10 MBPS. The outputs feature wide
common mode voltage range, making them suitable for party line
applications in noisy environments. The current limit and thermal
shutdown features protect the devices from line fault conditions.
These devices offer optimum performance when used with the
MC75173 and MC75175 line receivers.
Both devices are available in 16−pin plastic DIP and 20−pin wide
body surface mount packages.
• Meets EIA−485 Standard for Party Line Operation
• Meets EIA−422−A and CCITT Recommendations V.11 and X.27
• Operating Ambient Temperature: −40°C to +85°C
• High Impedance Outputs
• Common Mode Output Voltage Range: −7 to 12 V
• Positive and Negative Current Limiting
• Transmission Rates in Excess of 10 MBPS
• Thermal Shutdown at 150°C Junction Temperature, (± 20°C)
• Single 5.0 V Supply
• Pin Compatible with TI SN75172/4 and NS μA96172/4
• Interchangeable with MC3487 and AM26LS31 for EIA−422−A
Applications
w
QUAD EIA−485 LINE DRIVERS
SEMICONDUCTOR
TECHNICAL DATA
P SUFFIX
PLASTIC PACKAGE
CASE 648
DW SUFFIX
PLASTIC PACKAGE
CASE 751D
(SO−20L)
ORDERING INFORMATION
Device
Operating
Temperature Range
Package
TA = − 40° to +85°C
SO−20L
MC75172BDW
MC75174BDW
MC75174BP
SO−20L
Plastic DIP
These devices are available in Pb−free package(s). Specifications herein
apply to both standard and Pb−free devices. Please see our website at
www.onsemi.com for specific Pb−free orderable part numbers, or contact
your local ON Semiconductor sales office or representative.
© Semiconductor Components Industries, LLC, 2006
March, 2006 − Rev. 3
1
Publication Order Number:
MC75172B/D
MC75172B MC75174B
PIN CONNECTIONS
MC75172B
MC75174B
1A 1
16 VCC 1A 1
20 VCC
1A 1
16 VCC 1A 1
1Y 2
15 4A
1Y 2
19 4A
1Y 2
15 4A
1Y 2
19 4A
1Z 3
14 4Y
NC 3
18 4Y
1Z 3
14 4Y NC 3
18 4Y
En 4
13 4Z
1Z 4
17 NC
13 4Z
1Z 4
17 NC
2Z 5
12 En
En 5
16 4Z
En 4
12
2Z 5
11 3Z
2Z 6
15 En
2Y 6
En 5
12
2Z 6
16 4Z
2Y 6
12 En
34
11 3Z
2A 7
10 3Y
NC 7
14 3Z
2A 7
10 3Y
Gnd 8
9 3A
2Y 8
13 NC
Gnd 8
9 3A
2A 9
12 3Y
Gnd 10
11 3A
P Package
P Package
20 VCC
NC 7
15 En
34
14 3Z
2Y 8
13 NC
2A 9
12 3Y
Gnd 10
11 3A
DW Package
DW Package
MAXIMUM RATINGS
Rating
Symbol
Value
Unit
Power Supply Voltage
VCC
−0.5, +7.0
Vdc
Input Voltage (Data, Enable)
Vin
+7.0
Vdc
Input Current (Data, Enable)
Iin
−24
mA
Applied Output Voltage, when in 3−State Condition (VCC = 5.0 V)
Vza
−10, +14
Vdc
Applied Output Voltage, when VCC = 0 V
Vzb
±14
Output Current
IO
Self−Limiting
−
Tstg
−65, +150
°C
Storage Temperature
Devices should not be operated at these limits. The “Recommended Operating Conditions” table provides for actual device operation.
RECOMMENDED OPERATING CONDITIONS
Characteristic
Symbol
Min
Typ
Max
Unit
Power Supply Voltage
VCC
+4.75
+5.0
+5.25
Vdc
Input Voltage (All Inputs)
Vin
0
−
VCC
Vdc
Output Voltage in 3−State Condition, or when VCC = 0 V
Vcm
−7.0
−
+12
Vdc
Output Current (Normal data transmission)
IO
−65
−
+65
mA
Operating Ambient Temperature (see text)
EIA−485
EIA−422
TA
−40
0
−
−
+85
+85
All limits are not necessarily functional concurrently.
http://onsemi.com
2
°C
MC75172B MC75174B
ELECTRICAL CHARACTERISTICS (−40°C p TA p 85°C, 4.75 V p VCC p 5.25 V, unless otherwise noted.)
Characteristic
Output Voltage
Single−Ended Voltage
IO = 0
High @ IO = −33 mA
Low @ IO = +33 mA
Differential Voltage
Open Circuit (IO = 0)
RL = 54 Ω (Figure 1)
Symbol
Min
Typ
Max
Unit
VO
VOH
VOL
0
−
−
−
4.0
1.6
6.0
−
−
⎥ VOD1 ⎜
⎥ VOD2 ⎜
1.5
1.5
3.4
2.3
6.0
5.0
⎥ ΔVOD2 ⎜
⎥ VOD2A ⎜
⎥ ΔVOD2A ⎜
⎥ VOD3 ⎜
⎥ ΔVOD3 ⎜
VOS
⎥ ΔVOS ⎜
−
−
−
1.5
−
−
−
5.0
2.2
5.0
−
5.0
2.9
5.0
200
−
200
5.0
200
−
200
mVdc
Vdc
mVdc
Vdc
mVdc
Vdc
mVdc
IO(off)
IOZ
−50
−50
0
0
+50
+50
μA
IOSR
IOS
−150
−250
−
−
+150
+250
mA
Vdc
Change in Differential*, RL = 54 Ω (Figure 1)
Differential Voltage, RL = 100 Ω (Figure 1)
Change in Differential*, RL = 100 Ω (Figure 1)
Differential Voltage, −7.0 V p Vcm p 12 V (Figure 2)
Change in Differential*, −7.0 V p Vcm p 12 V (Figure 2)
Offset Voltage, RL = 54 Ω (Figure 1)
Change in Offset*, RL = 54 Ω (Figure 1)
Output Current (Each Output)
Power Off Leakage, VCC = 0, −7.0 V p VO p 12 V
Leakage in 3−State Mode, −7.0 V p VO p 12 V
Short Circuit Current to Ground
Short Circuit Current, −7.0 V p VO p 12 V
*Vin switched from 0.8 to 2.0 V.
Typical values determined at 25°C ambient and 5.0 V supply.
http://onsemi.com
3
MC75172B MC75174B
ELECTRICAL CHARACTERISTICS (−40°C p TAp 85°C, 4.75 V p VCC p 5.25 V, unless otherwise noted.)
Symbol
Min
Typ
Max
VIL(A)
VIL(B)
VIH
0
0
2.0
−
−
−
0.7
0.8
VCC
Current @ Vin = 2.7 V (All Inputs)
Current @ Vin = 0.5 V (All Inputs)
IIH
IIL
−
−100
0.2
−15
20
−
μA
Clamp Voltage (All Inputs, Iin = −18 mA)
VIK
−1.5
−
−
Vdc
Thermal Shutdown Junction Temperature
Tjts
−
+150
−
°C
Power Supply Current (Outputs Open, VCC = 5.25 V)
Outputs Enable
Outputs Disabled
ICC
−
−
60
30
70
40
Symbol
Min
Typ
Max
tPLH
tPHL
−
−
23
18
30
30
Propagation Delay − Input to Differential Output (Figure 4)
Input Low−to−High
Input High−to−Low
tPLH(D)
tPHL(D)
−
−
15
17
25
25
Differential Output Transition Time (Figure 4)
tdr, tdf
−
19
25
tSK1
tSK2
tSK3
−
−
−
0.2
1.5
1.5
−
−
−
Characteristics
Inputs
Low Level Voltage (Pins 4 & 12, MC75174B only)
Low Level Voltage (All Other Pins)
High Level Voltage (All Inputs)
Unit
Vdc
mA
TIMING CHARACTERISTICS (TA = 25°C, VCC = 5.0 V)
Characteristics
Propagation Delay − Input to Single−ended Output (Figure 3)
Output Low−to−High
Output High−to−Low
Unit
ns
ns
Skew Timing
⎜tPLHD − tPHLD ⎜ for Each Driver
Max − Min tPLHD Within a Package
Max − Min tPHLD Within a Package
ns
ns
Enable Timing
Single−ended Outputs (Figure 5)
Enable to Active High Output
Enable to Active Low Output
Active High to Disable (using Enable)
Active Low to Disable (using Enable)
Enable to Active High Output (MC75172B only)
Enable to Active Low Output (MC75172B only)
Active High to Disable (using Enable, MC75172B only)
Active Low to Disable (using Enable, MC75172B only)
ns
Differential Outputs (Figure 6)
Enable to Active Output
Enable to Active Output (MC75172B only)
Enable to 3−State Output
Enable to 3−State Output (MC75172B only)
tPZH(E)
tPZL(E)
tPHZ(E)
tPLZ(E)
tPZH(E)
tPZL(E)
tPHZ(E)
tPLZ(E)
−
−
−
−
−
−
−
−
48
20
35
30
58
28
38
36
60
30
45
50
70
35
50
50
tPZD(E)
tPZD(E)
tPDZ(E)
tPDZ(E)
−
−
−
−
47
56
32
40
−
−
−
−
ns
http://onsemi.com
4
MC75172B MC75174B
VCC
VCC
375
RL/2
Vin
(0.8 or 2.0 V)
Vin
(0.8 or 2.0 V)
VOD2,A
RL/2
VOD3
58
+
VCM = 12 to −7.0 V
375
VOS
Figure 1. VDD Measurement
Figure 2. Common Mode Test
3.0 V
VCC
1.5 V
0V
tPLH
tPHL
27 Ω
Y
Vin
Vin
2.3 V
1.5 V
Output
Z
15 pF
3.0 V
3.0 V
Output Y
VOL
S.G.
tPLH
Output Z
tPHL
VOH
3.0 V
3.0 V
Figure 3. Propagation Delay, Single−Ended Outputs
3.0 V
VCC
Vin
Vin
S.G.
54
50 pF
1.5 V
1.5 V
0V
tPLHD
VOD
VOD
tPHLD
1.5 V
50%
−1.5 V
tdr
NOTES: 1. S.G. set to: f p 1.0 MHz; duty cycle = 50%; tr, tf, p 5.0 ns.
2. tSK1 = ⎥ tPLHD − tPHLD⎥ for each driver.
3. tSK2 computed by subtracting the shortest tPLHD from the longest tPLHD of the 4 drivers within a package.
4. tSK3 computed by subtracting the shortest tPHLD from the longest tPHLD of the 4 drivers within a package.
Figure 4. Propagation Delay, Differential Outputs
http://onsemi.com
5
1.5 V
50%
−1.5 V
[4.6 V
tdf
MC75172B MC75174B
3.0 V
VCC
0 or 3.0 V
1.5 V
1.5 V
Vin
0V
tPZH(E)
Vout
tPHZ(E)
110Ω
Vin
50 pF
3.0 V
VOH
0.5 V
2.3 V
Vout
S.G.
VCC
VCC
3.0 V
110Ω
0 or 3.0 V
1.5 V
1.5 V
Vin
0V
tPZL(E)
Vout
tPLZ(E)
50 pF
Vin
3.0 V
Vout
2.3 V
0.5 V
S.G.
VOL
Figure 5. Enable Timing, Single−Ended Outputs
3.0 V
VCC
1.5 V
Vin
0 or 3.0 V
Vin
54
50 pF
1.5 V
0V
tPZD(E)
VOD
tPDZ(E)
3.0 V
1.5 V
VOD
1.5 V
0
S.G.
0
Disabled
NOTES: 1. S.G. set to: f p 1.0 MHz; duty cycle = 50%; tf, tf, p 5.0 ns.
2. Vin is inverted for Enable measurements.
Figure 6. Enable Timing, Differential Outputs
http://onsemi.com
6
Active
Disabled
MC75172B MC75174B
2.0
VOL, OUTPUT VOLTAGE (V)
VOL, OUTPUT VOLTAGE (V)
2.0
1.5
1.0
0.5
IOL = 27.8 mA
1.75
IOL = 20.0 mA
1.5
1.25
4.75 V p VCC p 5.25 V
4.75V p VCC p5.25 V
TA = 25°C
0
0
10
20
30
40
50
IOL, OUTPUT CURRENT (mA)
60
1.0
− 40
70
Figure 7. Single−Ended Output Voltage
versus Output Sink Current
VCC = 5.25 V
4.0
VCC = 5.00 V
4.0
VCC = 4.75 V
3.0
2.0
TA = 25°C
1.0
0
− 10
− 20
− 30
− 40
− 50
IOH, OUTPUT CURRENT (mA)
− 60
3.5
VCC = 4.75 V
− 70
− 40
VOD , DIFFERENTIAL OUTPUT VOLTAGE (V)
VOD , DIFFERENTIAL OUTPUT VOLTAGE (V)
VCC = 5.25 V
VCC = 5.0 V
VCC = 4.75 V
1.0
VOD
TA = 25°C
0
0
10
20
30
40
50
IO, OUTPUT CURRENT (mA)
60
− 20
0
40
60
20
TA, AMBIENT TEMPERATURE (°C)
85
Figure 10. Single−Ended Output
Voltage versus Temperature
3.0
IO
IOH = −27.8 mA
3.25
4.0
0.8 or
2.0 V
85
IOH = −20.0 mA
3.75
Figure 9. Single−Ended Output Voltage
versus Output Source Current
2.0
0
20
40
60
TA, AMBIENT TEMPERATURE (°C)
Figure 8. Single−Ended Output Voltage
versus Temperature
VOH, OUTPUT VOLTAGE (V)
VOH, OUTPUT VOLTAGE (V)
5.0
− 20
70
4.0
3.0
IO = 20.0 mA
IO = 27.8 mA
2.0
1.0
0.8 or
2.0 V
0
−40
Figure 11. Output Differential Voltage
versus Load Current
−20
IO
VOD
VCC = 4.75 V
0
20
40
60
TA, AMBIENT TEMPERATURE (°C)
Figure 12. Output Differential Voltage
versus Temperature
http://onsemi.com
7
85
MC75172B MC75174B
20
IOX, IOZ, LEAKAGE CURRENT (μ A)
IOZ, LEAKAGE CURRENT (μ A)
2.0
1.0
0
15
10
5.0
Vout = 7.0 V
−5.0
−1.0
TA = 25°C
En = Low, En = High
−2.0
−7.0
−3.0
1.0
5.0
9.0
Vz, APPLIED OUTPUT VOLTAGE (V)
−10
−20
−40
12
−20
0
40
20
TA, AMBIENT TEMPERATURE (°C)
60
85
Figure 14. Output Leakage Current
versus Temperature
150
IOS , SHORT CIRCUIT CURRENT (mA)
5.0
0
Enable
Pins
− 5.0
Driver
Inputs
− 10
− 15
4.75 p VCC p 5.25 V
TA = 25°C
− 20
− 25
− 0.5
En = Low, En = High
or VCC = 0 V
−15
Figure 13. Output Leakage Current
versus Output Voltage
I in , INPUT CURRENT (μ A)
Vout = +12 V
0
0.5
1.5
2.5
3.5
Vin, INPUT VOLTAGE (V)
4.5
5.5
Normally Low Output
90
30
0
Normally High Output
− 30
−9
0
−150
−7.0
Figure 15. Input Current
versus Input Voltage
TA = 25°C
4.75 p VCC p 5.25 V
−3.0
1.0
5.0
9.0
Vz, APPLIED OUTPUT VOLTAGE (V)
Figure 16. Short Circuit Current
versus Common Mode Voltage
http://onsemi.com
8
12
MC75172B MC75174B
APPLICATIONS INFORMATION
Description
The MC75172B and MC75174B are differential line
drivers designed to comply with EIA−485 Standard (April
1983) for use in balanced digital multipoint systems
containing multiple drivers. The drivers also comply with
EIA−422−A and CCITT Recommendations V.11 and X.27.
The drivers meet the EIA−485 requirement for protection
from damage in the event that two or more drivers attempt
to transmit data simultaneously on the same cable. Data
rates in excess of 10 MBPS are possible, depending on the
cable length and cable characteristics. A single power
supply, 5.0 V, ±5%, is required at a nominal current of
60 mA, plus load currents.
The drivers are protected from short circuits by two
methods:
a) Current limiting is provided at each output, in both
the source and sink direction, for shorts to any
voltage within the range of 12V to −7.0V, with
respect to circuit ground (see Figure 16). The short
circuit current will flow until the fault is removed, or
until the thermal shutdown circuit activates (see
below). The current limiting circuit has a negative
temperature coefficient and requires no resetting
upon removal of the fault condition.
b) A thermal shutdown circuit disables the outputs
when the junction temperature reaches 150°C,
± 20°C. The thermal shutdown circuit has a
hysteresis of ≈ 12°C to prevent oscillations. When
this circuit activates, the output stage of each driver
is put into the high impedance mode, thereby
shutting off the output currents. The remainder of the
internal circuitry remains biased. The outputs will
become active once again as the IC cools down.
Outputs
Each output (when active) will be a low or a high voltage,
which depends on the input state and the load current (see
Table 1, 2 and Figures 7 to 10). The graphs apply to each
driver, regardless of how many other drivers within the
package are supplying load current.
Table 1. MC75172B Truth Table
Enables
Outputs
Data Input
EN
EN
Y
Z
Driver Inputs
H
L
H
L
X
H
H
X
X
L
X
X
L
L
H
H
L
H
L
Z
L
H
L
H
Z
The driver inputs determine the state of the outputs in
accordance with Tables 1 and 2. The driver inputs have a
nominal threshold of 1.2 V, and their voltage must be kept
within the range of 0 V to VCC for proper operation. If the
voltage is taken more than 0.5 V below ground, excessive
currents will flow, and proper operation of the drivers will
be affected. An open pin is equivalent to a logic high, but
good design practices dictate that inputs should never be
left open. The characteristics of the driver inputs are shown
in Figure 15. This graph is not affected by the state of the
Enable pins.
Table 2. MC75174B Truth Table
Outputs
Data Input
Enable
Y
H
L
X
H
H
L
H
L
Z
Z
L
H
Z
H = Logic high, L = Logic low, X = Irrelevant, Z = High impedance
Enable Logic
Each driver’s outputs are active when the Enable inputs
(Pins 4 and 12) are true according to Tables 1 and 2.
The Enable inputs have a nominal threshold of 1.2 V and
their voltage must be kept within the range of 0 V to VCC
for proper operation. If the voltage is taken more than 0.5 V
below ground, excessive currents will flow, and proper
operation of the drivers will be affected. An open pin is
equivalent to a logic high, but good design practices dictate
that inputs should never be left open. The Enable input
characteristics are shown in Figure 15.
The two outputs of a driver are always complementary.
A “high” output can only source current out, while a “low”
output can only sink current (except for short circuit current
− see Figure 16).
The outputs will be in the high impedance mode when:
a) the Enable inputs are set according to Table 1 or 2;
b) VCC is less than 1.5 V;
c) the junction temperature exceeds the trip point of
the thermal shutdown circuit (see below). When in
this condition, the output’s source and sink
capability are shut off, and only leakage currents
will flow (see Figures 13, 14). Disabled outputs may
be taken to any voltage between −7.0 V and 12 V
without damage.
Operating Temperature Range
The minimum ambient operating temperature is listed as
−40°C to meet EIA−485 specifications, and 0°C to meet
EIA−422−A specifications. The higher VOD required by
EIA−422−A is the reason for the narrower temperature range.
http://onsemi.com
9
MC75172B MC75174B
drivers. From Figures 8 and 10 (adjusted for VCC = 5.0 V),
VOL [1.38 V, and VOH [4.27 V. The power dissipated
in each driver is:
{(5.0 − 4.27) • 0.020} + (1.38 • 0.0278) = 53 mW
Since each driver dissipates 53 mW, the use of all four
drivers in a package would be marginal. Options include
reducing the load current, reducing the ambient
temperature, and/or providing a heat sink.
The maximum ambient operating temperature
(applicable to both EIA−485 and EIA−422−A) is listed as
85°C. However, a lower ambient may be required
depending on system use (i.e. specifically how many
drivers within a package are used) and at what current
levels they are operating. The maximum power which may
be dissipated within the package is determined by:
PDmax +
where:
T
–T
Jmax A
R
qJA
System Requirements
EIA−485 requires each driver to be capable of
transmitting data differentially to at least 32 unit loads, plus
an equivalent DC termination resistance of 60Ω, over a
common mode voltage of −7.0 to 12 V. A unit load (U.L.),
as defined by EIA−485, is shown in Figure 17.
RθJA = package thermal resistance (typical
70°C/W for the DIP package, 85°C/W for
SOIC package);
TJmax = max. operating junction
temperature, and
TA = ambient temperature.
I
1.0 mA
Since the thermal shutdown feature has a trip point of
150°C, ±20°C, TJmax is selected to be 130°C. The power
dissipated within the package is calculated from:
PD
where:
−7.0 V
= {[(VCC − VOH) • IOH] + VOL • IOL)} each
driver = + (VCC • ICC)
VCC = the supply voltage;
VOH, VOL are measured or estimated from
Figures 7 to 10;
ICC = the quiescent power supply current
(typical 60 mA).
V
5.0 V
12 V
−0.8 mA
Reprinted from EIA−485, Electronic Industries Association,
Washington,DC.
Figure 17. Unit Load Definition
As indicated in the equation, the first term (in brackets)
must be calculated and summed for each of the four drivers,
while the last term is common to the entire package.
Example 1: TA = 25°C, IOL = IOH = 55 mA for each
driver, VCC = 5.0 V, DIP package. How many drivers per
package can be used?
Maximum allowable power dissipation is:
PD max +
−3.0 V
A load current within the shaded regions represents an
impedance of less than one U.L., while a load current of a
magnitude outside the shaded area is greater than one U.L.
A system’s total load is the sum of the unit load equivalents
of each receiver’s input current, and each disabled driver’s
output leakage current. The 60Ω termination resistance
mentioned above allows for two 120Ω terminating
resistors.
Using the EIA−485 requirements (worst case limits), and
the graphs of Figures 7 and 9, it can be determined that the
maximum current an MC75172B or MC75174B driver will
source or sink is [65 mA.
130°C * 25°C
+ 1.5 W
70°CńW
Since the power supply current of 60 mA dissipates
300 mW, that leaves 1.2 W (1.5 W − 0.3 W) for the drivers.
From Figures 7 and 9, VOL [1.75 V, and VOH [3.85 V.
The power dissipated in each driver is:
{(5.0 − 3.85) • 0.055} + (1.75 • 0.055) = 160 mW.
Since each driver dissipates 160 mW, the four drivers per
package could be used in this application.
Example 2: TA = 85°C, IOL = 27.8 mA, IOH = 20 mA for
each driver, VCC = 5.0 V, SOIC package. How many drivers
per package can be used?
Maximum allowable power dissipation is:
System Example
An example of a typical EIA−485 system is shown in
Figure 18. In this example, it is assumed each receiver’s
input characteristics correspond to 1.0 U.L. as defined in
Figure 17. Each “off” driver, with a maximum leakage of
±50 μA over the common mode range, presents a load of
[0.06 U.L. The total load for the active driver is therefore
8.3 unit loads, plus the parallel combination of the two
terminating resistors (60Ω). It is up to the system software
to control the driver Enable pins to ensure that only one
driver is active at any time.
PDmax + 130°C * 85°C + 0.53 W
85°CńW
Since the power supply current of 60 mA dissipates
300 mW, that leaves 230 mW (530 mW − 300 mW) for the
http://onsemi.com
10
MC75172B MC75174B
Termination Resistors
Leaving off the terminations will generally result in
reflections which can have amplitudes of several volts
above VCC or below ground. These overshoots and
undershoots can disrupt the driver and/or receiver
operation, create false data, and in some cases damage
components on the bus.
Transmission line theory states that, in order to preserve
the shape and integrity of a waveform traveling along a
cable, the cable must be terminated in an impedance equal
to its characteristic impedance. In a system such as that
depicted in Figure 18, in which data can travel in both
directions, both physical ends of the cable must be
terminated. Stubs, leading to each receiver and driver,
should be as short as possible.
En
R
R
TTL
#1
TTL
TTL
D
#2
#3
En
TTL
D
RT
#1
5 “off” drivers (@ 0.06 U.L. each),
+8 receivers (@ 1.0 U.L. each) = 8.3 Unit Loads
RT = 120 Ω at each end of the cable.
120 Ω
Twisted
Pair
En
TTL
D
R
TTL
#2
#3
En
D
TTL
#4
R
TTL
#4
TTL
R
#6
En
TTL
D
RT
#6
En
R
TTL
#8
R
R
TTL
#7
TTL
#5
TTL
D
#5
NOTES: 1. Terminating resistors RT must be located at the physical ends of the cable.
2. Stubs should be as short as possible.
3. Circuit ground of all drivers and receivers must be connected via a dedicated wire within the cable.
Do not rely on chassis ground or power line ground.
Figure 18. Typical EIA−485 System
http://onsemi.com
11
MC75172B MC75174B
Comparing System Requirements
Characteristic
Symbol
EIA−485
EIA−422−A
V.11 and X.27
GENERATOR (DRIVER)
Output Impedance (Note 1)
Zout
Not Specified
t 100 Ω
50 10 100 Ω
Open Circuit Voltage
Differential
Single−Ended
VOCD
VOCS
1.5 to 6.0 V
t 6.0 V
p 6.0 V
p 6.0 V
p 6.0 V, w/3.9 kΩ, Load
p 6.0 V, w/3.9 kΩ, Load
Loaded Differential Voltage
VOD
1.5 to 5.0 V, w/54 Ω load
q 2.0 V or q 0.5
VOCD, w/100 Ω load
q 2.0 V or q 0.5 VOCD,
w/100 Ω load
Differential Voltage Balance
ΔVOD
t 200 mV
p 400 mV
t 400 mV
Output Common Mode Range
VCM
−7.0 to +12 V
Not Specified
Not Specified
Offset Voltage
VOS
−1.0 t VOS t 3.0 V
p 3.0 V
p 3.0 V
Offset Voltage Balance
ΔVOS
t 200 mV
p 400 mV
t 400 mV
Short Circuit Current
IOS
p 250 mA for −7.0 to
12 V
p 150 mA to ground
p 150 mA to ground
Leakage Current (VCC = 0)
IOLK
Not Specified
p 100 μA to −0.25 V
thru 6.0 V
p 100 μA to ± 0.25 V
Output Rise/Fall Time (Note 2)
tr, tf
p 0.3 TB, w/54 Ω/1150 pF
load
p 0.1 TB or p 20 ns,
w/100 Ω load
p 0.1 TB or p 20 ns,
± 200 mV
± 200 mV
± 300 mV
w/100 Ω load
RECEIVER
Input Sensitivity
Vth
Input Bias Voltage
Vbias
p 3.0 V
p 3.0 V
p 3.0 V
Input Common Mode Range
Vcm
−7.0 to 12 V
−7.0 to 7.0 V
−7.0 to 7.0 V
Dynamic Input Impedance
Rin
Spec number of U.L.
q 4 kΩ
q 4 kΩ
NOTES: 1. Compliance with V.11 and X.27 (Blue book) output impedance requires external resistors in series with the outputs of the MC75172B and MC75174B.
2. TB = Bit time.
Additional Information
Copies of the EIA Recommendations (EIA−485 and EIA−422−A) can be obtained from the Electronics Industries
Association, Washington, D.C. (202−457−4966). Copies of the CCITT Recommendations (V.11 and X.27) can be obtained
from the United States Department of Commerce, Springfield, VA (703−487−4600).
http://onsemi.com
12
MC75172B MC75174B
OUTLINE DIMENSIONS
P SUFFIX
PLASTIC PACKAGE
CASE 648−08
ISSUE R
−A−
16
9
1
8
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
B
F
C
L
S
−T−
H
SEATING
PLANE
K
G
D
M
J
16 PL
0.25 (0.010)
M
T A
M
http://onsemi.com
13
DIM
A
B
C
D
F
G
H
J
K
L
M
S
INCHES
MIN
MAX
0.740
0.770
0.250
0.270
0.145
0.175
0.015
0.021
0.040
0.70
0.100 BSC
0.050 BSC
0.008
0.015
0.110
0.130
0.295
0.305
0_
10 _
0.020
0.040
MILLIMETERS
MIN
MAX
18.80
19.55
6.35
6.85
3.69
4.44
0.39
0.53
1.02
1.77
2.54 BSC
1.27 BSC
0.21
0.38
2.80
3.30
7.50
7.74
0_
10 _
0.51
1.01
MC75172B MC75174B
OUTLINE DIMENSIONS
DW SUFFIX
PLASTIC PACKAGE
CASE 751D−05
(SO−20L)
ISSUE F
A
20
q
X 45 _
M
E
h
H
10X
0.25
NOTES:
1. DIMENSIONS ARE IN MILLIMETERS.
2. INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.5M, 1994.
3. DIMENSIONS D AND E DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE.
5. DIMENSION B DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE PROTRUSION SHALL
BE 0.13 TOTAL IN EXCESS OF B DIMENSION AT
MAXIMUM MATERIAL CONDITION.
11
B
M
D
1
10
20X
B
B
0.25
M
T A
S
B
S
L
A
18X
e
A1
SEATING
PLANE
C
T
DIM
A
A1
B
C
D
E
e
H
h
L
q
MILLIMETERS
MIN
MAX
2.35
2.65
0.10
0.25
0.35
0.49
0.23
0.32
12.65
12.95
7.40
7.60
1.27 BSC
10.05
10.55
0.25
0.75
0.50
0.90
0_
7_
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any
liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental
damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over
time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under
its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body,
or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death
may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees,
subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of
personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part.
SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
N. American Technical Support: 800−282−9855 Toll Free
Literature Distribution Center for ON Semiconductor
USA/Canada
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada
Phone: 81−3−5773−3850
Email: [email protected]
http://onsemi.com
14
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
For additional information, please contact your
local Sales Representative.
MC75172B/D
Similar pages