ATMEL ATXMEGA128A4U-AU 8/16-bit atmel xmega a4u microcontroller Datasheet

Features
• High-performance, Low-power Atmel® AVR® XMEGA® 8/16-bit Microcontroller
• Non-volatile Program and Data Memories
•
•
•
•
•
– 16K - 128KBytes of In-System Self-Programmable Flash
– 4K - 8KBytes Boot Code Section with Independent Lock Bits
– 1K - 2KBytes EEPROM
– 2K - 8KBytes Internal SRAM
Peripheral Features
– Four-channel DMA Controller
– Eight-channel Event System
– Five 16-bit Timer/Counters
Three Timer/Counters with 4 Output Compare or Input Capture channels
Two Timer/Counters with 2 Output Compare or Input Capture channels
High-Resolution Extensions on all Timer/Counters
Advanced Waveform Extension on one Timer/Counter
– One USB device Interface
USB 2.0 full speed (12Mbps) and low speed (1.5Mbps) device compliant
32 Endpoints with full configuration flexibility
– Five USARTs with IrDA support for one USART
– Two Two-Wire Interfaces with dual address match (I2C and SMBus compatible)
– Two Serial Peripheral Interfaces (SPIs)
– AES and DES Crypto Engine
– CRC-16 (CRC-CCITT) and CRC-32 (IEEE 802.3) Generator
– 16-bit Real Time Counter with Separate Oscillator
– One Twelve-channel, 12-bit, 2MSPS Analog to Digital Converter
– One Two-channel, 12-bit, 1MSPS Digital to Analog Converter
– Two Analog Comparators with Window compare function, and current source feature
– External Interrupts on all General Purpose I/O pins
– Programmable Watchdog Timer with Separate On-chip Ultra Low Power Oscillator
– QTouch® library support
Capacitive touch buttons, sliders and wheels
Up to 64 sense channels
Special Microcontroller Features
– Power-on Reset and Programmable Brown-out Detection
– Internal and External Clock Options with PLL and Prescaler
– Programmable Multi-level Interrupt Controller
– Five Sleep Modes
– Programming and Debug Interfaces
PDI (Program and Debug Interface)
I/O and Packages
– 34 Programmable I/O Pins
– 44 - lead TQFP
– 44 - pad VQFN/QFN
– 49 - ball VFBGA
Operating Voltage
– 1.6 – 3.6V
Operating Frequency
– 0 – 12MHz from 1.6V
– 0 – 32MHz from 2.7V
8/16-bit Atmel
XMEGA A4U
Microcontroller
ATxmega128A4U
ATxmega64A4U
ATxmega32A4U
ATxmega16A4U
Preliminary
Typical Applications
•
•
•
•
•
Industrial control
Factory automation
Building control
Board control
White Goods
•
•
•
•
•
Climate control
RF and ZigBee
USB Connectivity
Sensor control
Optical
•
•
•
•
•
Low power battery applications
Power tools
HVAC
Utility Metering
Medical Applications
8387A–AVR–07/11
XMEGA A4U
1. Ordering Information
Ordering Code
Flash (Bytes) EEPROM (Bytes) SRAM (Bytes)
ATxmega128A4U-AU
128K + 8K
2K
8K
ATxmega64A4U-AU
64K + 4K
2K
4K
ATxmega32A4U-AU
32K + 4K
1K
4K
ATxmega16A4U-AU
16K + 4K
1K
2K
ATxmega128A4U-MH
128K + 8K
2K
8K
ATxmega64A4U-MH
64K + 4K
2K
4K
ATxmega32A4U-MH
32K + 4K
1K
4K
ATxmega16A4U-MH
16K + 4K
1K
2K
ATxmega128A4U-CU
128K + 8K
2K
8K
ATxmega64A4U-CU
64K + 4K
2K
4K
ATxmega32A4U-CU
32K + 4K
1K
4K
ATxmega16A4U-CU
16K + 4K
1K
2K
Notes:
Speed (MHz)
Power Supply
Package(1)(2)(3)
Temp
44A
32
1.6 - 3.6V
44M1
-40°C - 85°C
49C2
1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information.
2. Pb-free packaging, complies to the European Directive for Restriction of Hazardous Substances (RoHS directive). Also
Halide free and fully Green.
3. For packaging information see ”Packaging information” on page 61.
Package Type
44A
44-Lead, 10 x 10mm Body Size, 1.0mm Body Thickness, 0.8mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP)
44M1
44-Pad, 7x7x1mm Body, Lead Pitch 0.50mm, 5.20mm Exposed Pad, Thermally Enhanced Plastic Very Thin Quad No Lead Package (VQFN)
49C2
49-Ball (7 x 7 Array), 0.65mm Pitch, 5.0 x 5.0 x 1.0mm, Very Thin, Fine-Pitch Ball Grid Array Package (VFBGA)
2
8387A–AVR–07/11
XMEGA A4U
2. Pinout/Block Diagram
Block Diagram and QFN/TQFP pinout
PR1
PR0
RESET/PDI
PDI
37
36
35
34
AVCC
39
GND
PA0
40
38
PA1
41
General Purpose I/O
PA2
Analog function
42
External clock / Crystal pins
PA3
Digital function
43
Programming, debug, test
PA4
Power / Ground
44
Figure 2-1.
Port R
PA6
2
PA7
3
PB0
4
PB1
5
PB2
6
PB3
7
DATA BUS
Port A
1
OSC/CLK
Control
Watchdog
Crypto /
CRC
Power
Supervision
Real Time
Counter
Watchdog
Timer
Reset
Controller
Sleep
Controller
Event System
Controller
Interrupt
Controller
OCD
Prog/Debug
Interface
AREF
ADC
AC0:1
Port B
PA5
BUS
matrix
TEMPREF
AREF
DAC
DMA
Controller
CPU
VREF
FLASH
GND
EEPROM
33
PE3
32
PE2
31
VCC
30
GND
29
PE1
28
PE0
27
PD7
26
PD6
25
PD5
24
PD4
23
PD3
SRAM
8
DATA BUS
Note:
TWI
TC0
USART0
USB
SPI
USART0:1
13
14
15
16
17
18
19
20
21
22
PC3
PC4
PC5
PC6
PC7
GND
VDD
PD0
PD1
PD2
Port E
12
Port D
PC2
Port C
TC0:1
11
TWI
PC1
SPI
10
TC0:1
PC0
EVENT ROUTING NETWORK
USART0:1
9
IRCOM
VCC
For full details on pinout and pin functions refer to ”Pinout and Pin Functions” on page 51.
3
8387A–AVR–07/11
XMEGA A4U
Figure 2-2.
BGA pinout
Top view
1
Table 2-1.
2
3
4
5
Bottom view
6
7
7
6
5
4
3
2
1
A
A
B
B
C
C
D
D
E
E
F
F
G
G
BGA pinout
1
2
3
4
5
6
PA3
AVCC
GND
PR1
PR0
PDI_DATA
PE3
PA4
PA1
PA0
GND
RESET/
PDI_CLK
PE2
VCC
C
PA5
PA2
PA6
PA7
GND
PE1
GND
D
PB1
PB2
PB3
PB0
GND
PD7
PE0
E
GND
GND
PC3
GND
PD4
PD5
PD6
F
VCC
PC0
PC4
PC6
PD0
PD1
PD3
G
PC1
PC2
PC5
PC7
GND
VCC
PD2
A
B
4
8387A–AVR–07/11
XMEGA A4U
3. Overview
The Atmel® AVR® XMEGA® is a family of low power, high performance and peripheral rich 8/16bit microcontrollers based on the AVR® enhanced RISC architecture. By executing instructions
in a single clock cycle, AVR achieves throughputs CPU approaching 1Million Instructions Per
Second (MIPS) per MHz allowing the system designer to optimize power consumption versus
processing speed.
Atmel AVR CPU combines a rich instruction set with 32 general purpose working registers. All
the 32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing two independent registers to be accessed in one single instruction, executed in one clock cycle. The
resulting architecture is more code efficient while achieving throughputs many times faster than
conventional single-accumulator or CISC based microcontrollers.
The XMEGA A4U devices provide the following features: In-System Programmable Flash with
Read-While-Write capabilities, Internal EEPROM and SRAM, four-channel DMA Controller,
eight-channel Event System, Programmable Multi-level Interrupt Controller, 34 general purpose
I/Opins, 16-bit Real Time Counter, five flexible 16-bit Timer/Counters with compare and PWM
channels, one USB 2.0 full speed (12Mbps) Device Interface, five USARTs, two Two Wire Serial
Interfaces (TWIs), two Serial Peripheral Interfaces (SPIs), AES and DES crypto engine, one
Twelve-channel, 12-bit ADC with optional differential input with programmable gain, one Twochannel 12-bit DAC, two analog comparators with window mode, programmable Watchdog
Timer with separate Internal Oscillator, accurate internal oscillators with PLL and prescaler and
programmable Brown-Out Detection.
The Program and Debug Interface (PDI), a fast 2-pin interface for programming and debugging,
is available.
All XMEGA devices have five software selectable power saving modes. The Idle mode stops the
CPU while allowing the SRAM, DMA Controller, Event System, Interrupt Controller and all
peripherals to continue functioning. The Power-down mode saves the SRAM and register contents but stops the oscillators, disabling all other functions until the next TWI or pin-change
interrupt, or Reset. In Power-save mode, the asynchronous Real Time Counter continues to run,
allowing the application to maintain a timer base while the rest of the device is sleeping. In
Standby mode, the Crystal/Resonator Oscillator is kept running while the rest of the device is
sleeping. This allows very fast start-up from external crystal combined with low power consumption. In Extended Standby mode, both the main Oscillator and the Asynchronous Timer continue
to run. To further reduce power consumption, the peripheral clock to each individual peripheral
can optionally be stopped in Active mode and Idle sleep mode.
Atmel offers the QTouch® library for embedding capacitive touch buttons, sliders and wheels
functionality into AVR microcontrollers.
The device is manufactured using Atmel's high-density nonvolatile memory technology. The program Flash memory can be reprogrammed in-system through the PDI. A Bootloader running in
the device can use any interface to download the application program to the Flash memory. The
Bootloader software in the Boot Flash section will continue to run while the Application Flash
section is updated, providing true Read-While-Write operation. By combining an 8/16-bit RISC
CPU with In-System Self-Programmable Flash, the Atmel XMEGA A4U is a powerful microcontroller family that provides a highly flexible and cost effective solution for embedded applications.
5
8387A–AVR–07/11
XMEGA A4U
The Atmel® AVR® XMEGA® devices are supported with a full suite of program and system
development tools including: C compilers, macro assemblers, program debugger/simulators,
programmers, and evaluation kits.
3.1
Block Diagram
Figure 3-1.
XMEGA A4U Block Diagram
PR[0..1]
Digital function
Programming, debug, test
Analog function
Oscillator/Crystal/Clock
XTAL1/
TOSC1
General Purpose I/O
XTAL2/
TOSC2
Oscillator
Circuits/
Clock
Generation
PORT R (2)
Real Time
Counter
DATA BUS
PA[0..7]
PORT A (8)
Watchdog
Timer
Event System
Controller
Oscillator
Control
SRAM
ACA
DMA
Controller
ADCA
AREFA
Watchdog
Oscillator
Sleep
Controller
Prog/Debug
Controller
BUS Matrix
Power
Supervision
POR/BOD &
RESET
PDI
VCC
GND
RESET/
PDI_CLK
PDI_DATA
Int. Refs.
AES
Tempref
OCD
AREFB
DES
PORT B (8)
CRC
Interrupt
Controller
CPU
PB[0..7]
DACB
NVM Controller
Flash
IRCOM
EEPROM
DATA BUS
PORT D (8)
TWIE
TCE0
USARTE0
USB
SPID
TCD0:1
USARTD0:1
SPIC
PORT C (8)
TWIC
TCC0:1
USARTC0:1
EVENT ROUTING NETWORK
PORT E (4)
TOSC1 (optional)
TOSC2
(optional)
PC[0..7]
PD[0..7]
PE[0..3]
6
8387A–AVR–07/11
XMEGA A4U
4. Resources
A comprehensive set of development tools, application notes and datasheets are available for
download on http://www.atmel.com/avr.
4.1
Recommended reading
• XMEGA® AU Manual
• XMEGA Application Notes
This device data sheet only contains part specific information with a short description of each
peripheral and module. The XMEGA AU Manual describes the modules and peripherals in
depth. The XMEGA application notes contain example code and show applied use of the modules and peripherals.
All documentations are available from www.atmel.com/avr.
5. Capacitive touch sensing
The Atmel® QTouch® Library provides a simple to use solution to realize touch sensitive interfaces on most Atmel AVR® microcontrollers. The patented charge-transfer signal acquisition
offers robust sensing and includes fully debounced reporting of touch keys and includes Adjacent Key Suppression® (AKS™) technology for unambiguous detection of key events. The
QTouch Library includes support for the QTouch and QMatrix® acquisition methods.
Touch sensing can be added to any application by linking the appropriate Atmel QTouch Library
for the AVR Microcontroller. This is done by using a simple set of APIs to define the touch channels and sensors, and then calling the touch sensing API’s to retrieve the channel information
and determine the touch sensor states.
The QTouch Library is FREE and downloadable from the Atmel website at the following location:
www.atmel.com/qtouchlibrary. For implementation details and other information, refer to the
Atmel QTouch Library User Guide - also available for download from the Atmel website.
7
8387A–AVR–07/11
XMEGA A4U
6. AVR CPU
6.1
Features
• 8/16-bit high performance AVR RISC Architecture
– 142 instructions
– Hardware multiplier
• 32x8-bit registers directly connected to the ALU
• Stack in SRAM
• Stack Pointer accessible in I/O memory space
• Direct addressing of up to 16Mbytes of program and 16Mbytes of data memory
• True 16/24-bit access to 16/24-bit I/O registers
• Support for 8-, 16- and 32-bit Arithmetic
• Configuration Change Protection of system critical features
6.2
Overview
The Atmel® AVR® XMEGA® devices use the 8/16-bit AVR CPU. The main function of the CPU is
to execute the code and perform all calculations. The CPU is able to access memories, perform
calculations, control peripherals, and execute the program from the FLASH memory. Interrupt
handling is described in a separate section, refer to ”Interrupts and Programmable Multi-level
Interrupt Controller” on page 26.
Figure 6-1 on page 8 shows the CPU block diagram of the AVR CPU architecture.
Figure 6-1.
Block Diagram of the AVR CPU architecture
In order to maximize performance and parallelism, the AVR uses a Harvard architecture with
separate memories and buses for program and data. Instructions in the program memory are
executed with a single level pipelining. While one instruction is being executed, the next instruc-
8
8387A–AVR–07/11
XMEGA A4U
tion is pre-fetched from the Program Memory. This enables instructions to be executed in every
clock cycle.
The program memory is In-System Self-Programmable Flash memory.
6.3
ALU - Arithmetic Logic Unit
The Arithmetic Logic Unit (ALU) supports arithmetic and logic operations between registers or
between a constant and a register. Single register operations can also be executed. The ALU
operates in direct connection with all the 32 general purpose registers. In a single clock cycle,
arithmetic operations between general purpose registers or between a register and an immediate are executed and the result is stored back in the Register File. After an arithmetic or logic
operation, the Status Register is updated to reflect information about the result of the operation.
The ALU operations are divided into three main categories – arithmetic, logical, and bit-functions. Both 8- and 16-bit arithmetic is supported, and the instruction set allows for efficient
implementation of 32-bit arithmetic. The hardware multiplier supports signed and unsigned multiplication and fractional format.
6.4
Program Flow
After reset, the CPU starts to execute instructions from the lowest address in the Flash Program
Memory ‘0’. The Program Counter (PC) addresses the next instruction to be fetched. After a
reset, the PC is set to location ‘0’.
Program flow is provided by conditional and unconditional jump and call instructions, capable of
addressing the whole address space directly. Most AVR instructions use a 16-bit word format,
while a limited number uses a 32-bit format.
During interrupts and subroutine calls, the return address PC is stored on the Stack. The Stack
is allocated in the general data SRAM, and consequently the Stack size is only limited by the
total SRAM size and the usage of the SRAM. After reset the Stack Pointer (SP) points to the
highest address in the internal SRAM. The SP is read/write accessible in the I/O memory space,
enabling easy implementation of multiple stacks or stack areas. The data SRAM can easily be
accessed through the five different addressing modes supported in the AVR CPU.
6.5
Register File
The Register File consists of 32 x 8-bit general purpose working registers with single clock cycle
access time. The Register File supports the following input/output schemes:
• One 8-bit output operand and one 8-bit result input
• Two 8-bit output operands and one 8-bit result input
• Two 8-bit output operands and one 16-bit result input
• One 16-bit output operand and one 16-bit result input
Six of the 32 registers can be used as three 16-bit address register pointers for data space
addressing - enabling efficient address calculations. One of these address pointers can also be
used as an address pointer for look up tables in Flash program memory.
9
8387A–AVR–07/11
XMEGA A4U
7. Memories
7.1
Features
• Flash Program Memory
– One linear address space
– In-System Programmable
– Self-Programming and Bootloader support
– Application Section for application code
– Application Table Section for application code or data storage
– Boot Section for application code or bootloader code
– Separate read/write protection lock bits for all sections
– CRC Generator support for CRC check of a selectable flash program memory section
• Data Memory
– One linear address space
– Single cycle access from CPU
– SRAM
– EEPROM
Byte and page accessible
Optional memory mapping for direct load and store
– I/O Memory
Configuration and Status registers for all peripherals and modules
16bit-accessible General Purpose Register for global variables or flags
– Bus arbitration
Safe and deterministic handling of priority between CPU, DMA Controller, and other bus
masters
– Separate buses for SRAM, EEPROM, and I/O Memory
Simultaneous bus access for CPU and DMA Controller
• Production Signature Row Memory for factory programmed data
– ID for each microcontroller device type
– Serial number for each device
– Calibration bytes for factory calibrated peripherals
• User Signature Row
– One flash page in size
– Can be read and written from software
– Content is kept after chip erase
7.2
Overview
The Atmel® AVR® architecture has two main memory spaces, the Program Memory and the
Data Memory. Executable code can only reside in the Program Memory, while data can be
stored both in the Program Memory and the Data Memory. The Data Memory includes both
SRAM, and EEPROM Memory for nonvolatile data storage. All memory spaces are linear and
require no memory bank switching.
The available memory size configurations are shown in ”Ordering Information” on page 2. In
addition each device has a Flash memory signature row for calibration data, device identification, serial number etc.
Non Volatile Memory (NVM) spaces can be locked for further write and read/write operations.
This prevents unrestricted access to the application software.
10
8387A–AVR–07/11
XMEGA A4U
7.3
Flash Program Memory
The Atmel® AVR® XMEGA® devices contain On-chip In-System Reprogrammable Flash memory for program storage. The Flash memory can be accessed for read and write both from an
external programmer through the PDI, or from application software running in the device.
All AVR instructions are 16- or 32-bit wide, each Flash address location is 16-bit.
The Flash memory is organized in two main sections, the Application Section and the Boot
Loader section. The size of the different sections are fixed, but device dependent. These two
sections have separate lock bits and can have different levels of protection. The Store Program
Memory (SPM) instruction, used to write to the Flash from the application software, will only
operate when executed from the Boot Loader Section.
The Application Section contains an Application Table Section with separate lock settings. This
enables safe storage of Non-volatile data in the Program Memory.
Figure 7-1.
Flash Program Memory (Hexadecimal address)
Word Address
0
Application Section (Bytes)
(128K/64K/32K/16K)
...
EFFF
/
77FF
/
37FF
/
17FF
F000
/
7800
/
3800
/
1800
FFFF
/
7FFF
/
3FFF
/
1FFF
10000
/
8000
/
4000
/
2000
10FFF
/
87FF
/
47FF
/
27FF
Application Table Section (Bytes)
(4K/4K/4K/4K)
Boot Section (Bytes)
(8K/4K/4K/4K)
The Application Table Section and Boot Section can also be used for general application
software.
7.4
Data Memory
The Data memory contains the I/O Memory, internal SRAM, optionally memory mapped
EEPROM, and external memory if available. The data memory is organized as one continuous
memory section, see Figure 7-2 on page 12. To simplify development, I/O Memory, EEPROM
and SRAM will always have the same start addresses for all XMEGA devices.
11
8387A–AVR–07/11
XMEGA A4U
Figure 7-2.
Data Memory Map (Hexadecimal address)
Byte Address
0
FFF
ATxmega64A4U
I/O Registers
(4 KB)
1000
EEPROM
(2K)
17FF
Byte Address
0
FFF
1000
13FF
RESERVED
2000
2FFF
Internal SRAM
(4K)
ATxmega32A4U
I/O Registers
(4 KB)
EEPROM
(1K)
Byte Address
0
FFF
1000
13FF
RESERVED
2000
2FFF
Internal SRAM
(4K)
ATxmega16A4U
I/O Registers
(4 KB)
EEPROM
(1K)
RESERVED
2000
27FF
Byte Address
0
FFF
1000
17FF
Internal SRAM
(2K)
ATxmega128A4U
I/O Registers
(4 KB)
EEPROM
(2K)
RESERVED
2000
3FFF
7.4.1
Internal SRAM
(8K)
I/O Memory
The Status and configuration registers for peripherals and modules, including the CPU, are
addressable through I/O memory locations. All I/O locations can be accessed by the load
(LD/LDS/LDD) and store (ST/STS/STD) instructions, which is used to transfer data between the
32 registers in the Register File and the I/O memory. The IN and OUT instructions can address
I/O memory locations in the range 0x00 - 0x3F directly. In the address range 0x00 - 0x1F, single- cycle instructions for manipulation and checking of individual bits are available.
The I/O memory address for all peripherals and modules in XMEGA A4U is shown in the
”Peripheral Module Address Map” on page 56.
7.4.2
SRAM Data Memory
The devices have internal SRAM memory for data storage.
7.4.3
EEPROM Data Memory
The devices have internal EEPROM memory for non-volatile data storage. It is addressable
either in a separate data space or it can be memory mapped into the normal data memory
space. The EEPROM memory supports both byte and page access.
7.5
Production Signature Row
The Production Signature Row is a separate memory section for factory programmed data. It
contains calibration data for functions such as oscillators and analog modules.
12
8387A–AVR–07/11
XMEGA A4U
The production signature row also contains an ID that identifies each microcontroller device
type, and a serial number that is unique for each manufactured device. The device ID for the
devices is shown in Table 7-1 on page 13. The serial number consists of the production LOT
number, wafer number, and wafer coordinates for the device.
The production signature row can not be written or erased, but it can be read from both application software and external programming.
Table 7-1.
Device ID bytes for XMEGA A4U devices.
Device
7.6
Device ID bytes
Byte 2
Byte 1
Byte 0
ATxmega16A4U
41
94
1E
ATxmega32A4U
41
95
1E
ATxmega64A4U
46
96
1E
ATxmega128A4U
46
97
1E
User Signature Row
The User Signature Row is a separate memory section that is fully accessible (read and write)
from application software and external programming. It is one flash page in size, and is meant
for static user parameter storage, such as calibration data, custom serial numbers or identification numbers, random number seeds etc. This section is not erased by Chip Erase commands
that erase the Flash, and requires a dedicated erase command. This ensures parameter storage
during multiple program/erase session and on-chip debug sessions.
13
8387A–AVR–07/11
XMEGA A4U
7.7
Flash and EEPROM Page Size
The Flash Program Memory and EEPROM data memory are organized in pages. The pages are
word accessible for the Flash and byte accessible for the EEPROM.
Table 7-2 on page 14 shows the Flash Program Memory organization. Flash write and erase
operations are performed on one page at a time, while reading the Flash is done one byte at a
time. For Flash access the Z-pointer (Z[m:n]) is used for addressing. The most significant bits in
the address (FPAGE) give the page number and the least significant address bits (FWORD)
give the word in the page.
Table 7-2.
Devices
Flash
Page Size
Size
(words)
Number of words and Pages in the Flash.
FWORD
FPAGE
Application
Size
Boot
No of Pages
Size
No of Pages
ATxmega16A4U
16K + 4K
128
Z[6:0]
Z[13:7]
16K
64
4K
16
ATxmega32A4U
32K + 4K
128
Z[6:0]
Z[14:7]
32K
128
4K
16
ATxmega64A4U
64K + 4K
128
Z[6:0]
Z[15:7]
64K
256
4K
16
ATxmega128A4U
128K + 8K
128
Z[8:0]
Z[16:7]
128K
512
8K
32
Table 7-3 on page 14 shows EEPROM memory organization for the XMEGA A4U devices.
EEPROM write and erase operations can be performed one page or one byte at a time, while
reading the EEPROM is done one byte at a time. For EEPROM access the NVM Address Register (ADDR[m:n]) is used for addressing. The most significant bits in the address (E2PAGE) give
the page number and the least significant address bits (E2BYTE) give the byte in the page.
Table 7-3.
Devices
Number of Bytes and Pages in the EEPROM.
EEPROM
Page Size
Size
(Bytes)
E2BYTE
E2PAGE
No of Pages
ATxmega16A4U
1K
ATxmega32A4U
1K
32
ADDR[4:0]
ADDR[10:5]
32
32
ADDR[4:0]
ADDR[10:5]
32
ATxmega64A4U
ATxmega128A4U
2K
32
ADDR[4:0]
ADDR[10:5]
64
2K
32
ADDR[4:0]
ADDR[10:5]
64
14
8387A–AVR–07/11
XMEGA A4U
8. DMAC - Direct Memory Access Controller
8.1
Features
• The DMA Controller allows data transfers with minimal CPU intervention
•
•
•
•
•
•
•
8.2
– from data memory to data memory
– from data memory to peripheral
– from peripheral to data memory
– from peripheral to peripheral
Four DMA Channels with separate
– transfer triggers
– interrupt vectors
– addressing modes
Programmable channel priority
From 1byte to 16Mbytes of data in a single transaction
Multiple addressing modes
– Static
– Increment
– Decrement
Optional reload of source and destination address at the end of each
– Burst
– Block
– Transaction
Optional Interrupt on end of transaction
Optional connection to CRC Generator module for CRC on DMA data
Overview
The 4-channel Direct Memory Access (DMA) Controller can transfer data between memories
and peripherals, and thus offload these tasks from the CPU. It enables high data transfer rates
with minimum CPU intervention, and frees up CPU time. The 4 DMA channels enable up to four
independent and parallel transfers.
The DMA Controller can move data between SRAM and peripherals, between SRAM locations
and between peripheral registers directly. With access to all peripherals the DMA Controller can
handle automatic transfer of data to/from communication modules, as well as data retrieval from
ADC conversions, or data transfer to or from port pins. The DMA Controller can also read from
memory mapped EEPROM.
Data transfers are done in continues bursts of 1, 2, 4 or 8bytes. They build block transfers of
configurable size from 1 to 64Kbytes. A repeat counter can be used to repeat each block transfer for single transactions up to 16Mbytes. Source and destination addressing can be static,
incremental or decremental. Automatic reload of source and/or destination address can be done
after each burst, block transfer, or when transaction is complete. Application software, peripherals and events can trigger DMA transfers.
The four DMA channels have individual configuration and control settings. This include source,
destination, transfer triggers and transaction sizes. They have individual interrupt settings. Interrupt requests can be generated both when a transaction is complete or if the DMA Controller
detects an error on a DMA channel.
To allow for continuous transfers, two channels can be interlinked so that the second takes over
the transfer when the first is finished and vice versa.
15
8387A–AVR–07/11
XMEGA A4U
9. Event System
9.1
Features
• System for direct peripheral to peripheral communication and signaling
• Peripherals can directly send, receive and react to peripheral events
•
•
•
•
9.2
– CPU and DMA controller independent operation
– 100% predictable signal timing
– Short and guaranteed response time
8 Event Channels for up to 8 different and parallel signal routines and configurations
Events can be sent and/or used by most peripherals, clock system and software
Additional functions include
– Quadrature Decoders
– Digital Filtering of I/O pin change
Works in Active mode and Idle sleep mode
Overview
The Event System is system for direct peripheral to peripheral communication and signaling. It
enables the possibility for a change in one peripheral to automatically trigger actions in others
peripherals. It is designed for having a predictable system for short and guaranteed response
time between peripherals. It is simple and powerful since it allows for autonomous peripheral
control and interaction without use of interrupts, CPU or DMA Controller resources. It also
enables synchronized timing of actions in several peripheral modules.
The change in a peripheral is referred to as an event, and is it usually the same as the interrupt
conditions for the peripheral. These events can be directly passed to other peripherals using a
dedicated routing network called the Event Routing Network. How events are routed and used
by other peripherals is configured in software.
Figure 9-1 on page 17 shows a basic block diagram of all connected peripherals. The Event
System can directly connect together Analog and Digital converters, Analog Comparators, I/O
ports pins, the Real-time Counter, Timer/Counters, IR Communication Module (IRCOM), and
USB. It can also be used to trigger DMA transactions (DMA Controller). Events can also be generated from software and the Peripheral Clock.
16
8387A–AVR–07/11
XMEGA A4U
Figure 9-1.
Event system block diagram
CPU /
Software
DMA
Controller
Event Routing Network
ADC
AC
clkPER
Prescaler
Real Time
Counter
Event
System
Controller
Timer /
Counters
DAC
USB
Port pins
IRCOM
The Event Routing Network consists of eight software configurable multiplexers that control how
events are routed and used. This is called Event Channels and it enables up to eight parallel
event configurations and routings. The maximum routing latency between two peripherals is two
Peripheral clock cycles. The Event System works in both Active mode and Idle sleep mode.
17
8387A–AVR–07/11
XMEGA A4U
10. System Clock and Clock options
10.1
Features
• Fast start-up time
• Safe run-time clock switching
• Internal Oscillators:
•
•
•
•
•
•
10.2
– 32MHz run-time calibrated and tuneable oscillator
– 2MHz run-time calibrated oscillator
– 32.768kHz calibrated oscillator
– 32kHz Ultra Low Power (ULP) oscillator with 1kHz output
External clock options
– 0.4 - 16MHz Crystal Oscillator
– 32 kHz Crystal Oscillator
– External clock
PLL with 20 - 128MHz output frequency
– Internal and external clock options and 1 to 31x multiplication
– Lock detector
Clock Prescalers with 1 to 2048x division
Fast peripheral clocks running at 2 and 4 times the CPU clock frequency
Automatic Run-Time Calibration of internal oscillators
External oscillator and PLL lock failure detection with optional non maskable interrupt
Overview
The flexible clock system supports a large number of clock sources. It incorporates both accurate internal oscillators, and external crystal oscillators and resonator support. A high frequency
Phase Locked Loop (PLL) and clock prescalers can be used to generate a wide range of clock
frequencies. A calibration feature (DFLL) is available, and can be used for automatic runtime
calibration of the internal oscillators to remove frequency drift over voltage and temperate. An
Oscillator Failure Monitor can be enabled to issue a Non-Maskable Interrupt and switch to internal oscillator if the external oscillator or PLL fails.
When a reset occur, all clock sources except 32kHz Ultra Low Power oscillator are disabled.
After reset, the device will always start up running from the 2MHz internal oscillator. During normal operation, the System Clock source and prescalers can be changed from software at any
time.
Figure 10-1 on page 19 presents the principal clock system in the XMEGA. All of the clocks do
not need to be active at a given time. The clocks to the CPU and peripherals can be stopped
using sleep modes and power reduction registers.
18
8387A–AVR–07/11
XMEGA A4U
Figure 10-1. The Clock system, clock sources and clock distribution
Real Time
Counter
Peripherals
RAM
AVR CPU
Non-Volatile
Memory
clkPER
clkPER2
clkCPU
clkPER4
USB
clkUSB
System Clock Prescalers
Brown-out
Detector
Prescaler
Watchdog
Timer
clkSYS
clkRTC
System Clock Multiplexer
(SCLKSEL)
RTCSRC
USBSRC
DIV32
DIV32
DIV32
PLL
PLLSRC
DIV4
XOSCSEL
32 kHz
Int. ULP
32.768 kHz
Int. OSC
32.768 kHz
TOSC
32 MHz
Int. Osc
2 MHz
Int. Osc
XTAL2
XTAL1
10.3.1
TOSC2
TOSC1
10.3
0.4 – 16 MHz
XTAL
Clock Options
32kHz Ultra Low Power Internal Oscillator
This oscillator provides an approximate 32kHz clock. The 32kHz Ultra Low Power (ULP) Internal
Oscillator is a very low power clock source, and it is not designed for high accuracy. The oscillator employs a built in prescaler providing a 1kHz output. The oscillator is automatically
enabled/disabled when used as clock source for any part of the device. This oscillator can be
selected as clock source for the RTC.
10.3.2
32.768kHz Calibrated Internal Oscillator
This oscillator provides an approximate 32.768kHz clock. A factory-calibrated value is written to
the 32.768kHz oscillator calibration register during reset to ensure that the oscillator is runningwithin its specification. The calibration register can also be written from software for run-time
calibration of the oscillator frequency. The oscillator employs a built in prescaler providing both a
32.768kHz output and a 1.024kHz output.
19
8387A–AVR–07/11
XMEGA A4U
10.3.3
32.768kHz Crystal Oscillator
A 32.768kHz crystal oscillator can be connected between TOSC1 and TOSC2 pins and enable a
dedicated low frequency oscillator input circuit. A low power mode with reduced voltage swing
on TOSC2 is available. This oscillator can be used as clock source for the System Clock, RTC
and as the DFLL reference clock.
10.3.4
0.4 - 16MHz Crystal Oscillator
The 0.4 - 16MHz Crystal Oscillator is a driver intended for driving both external resonators and
crystals ranging from 400kHz to 16MHz.
10.3.5
2MHz Run-time Calibrated Internal Oscillator
The 2MHz Run-time Calibrated Internal Oscillator is the default system clock source after reset.
It is calibrated during production to provide a default frequency which is close to its nominal frequency. A Digital Frequency Looked Loop (DFLL) that can be enabled for automatic run-time
calibration of the oscillator to compensate for temperature and voltage drift to optimize the oscillator accuracy.
10.3.6
32MHz Run-time Calibrated Internal Oscillator
The 32MHz Run-time Calibrated Internal Oscillator is a high frequency oscillator. It is calibrated
during production to provide a default frequency which is close to its nominal frequency. A DFLL
that can be enabled for automatic run-time calibration of the oscillator to compensate for temperature and voltage drift to optimize the oscillator accuracy This oscillator can also be adjusted
and calibrated to any frequency between 30 and 55MHz.
10.3.7
External Clock input
The external clock input gives the possibility to connect a clock from an external source to
XTAL1.
10.3.8
PLL with Multiplication factor 1 - 31x
The PLL provides the possibility of multiplying a frequency by any number from 1 to 31. In combination with the prescalers, this gives a wide range of output frequencies from all clock sources.
20
8387A–AVR–07/11
XMEGA A4U
11. Power Management and Sleep Modes
11.1
Features
• Power management for adjusting power consumption and enabled functions
• 5 sleep modes:
– Idle
– Power-down
– Power-save
– Standby
– Extended standby
• Power Reduction register to disable clock and turn off unused peripherals in Active and Idle
mode
11.2
Overview
Various sleep modes and clock gating are implemented in order to tailor power consumption to
the application's requirement. This enables the microcontroller to stop unused modules to save
power.
All sleep modes are available and can be entered from Active mode. In Active mode the CPU is
executing application code. When the device enters sleep mode, program execution is stopped
and interrupts or reset is used to wake the device again. The application code decides when and
what sleep mode to enter. Interrupts from enabled peripherals and all enabled reset sources can
restore the microcontroller from sleep to Active mode.
In addition, Power Reduction registers provide a method to stop the clock to individual peripherals from software. When this is done, the current state of the peripheral is frozen and there is no
power consumption from that peripheral. This reduces the power consumption in Active mode
and Idle sleep mode and enable much more fine-tuned power management than sleep modes
alone.
11.3
Sleep Modes
11.3.1
Idle Mode
In Idle mode the CPU and Non-Volatile Memory are stopped, but all peripherals including the
Interrupt Controller, Event System and DMA Controller are kept running. Any enabled interrupt
will wake the device.
11.3.2
Power-down Mode
In Power-down mode all clocks, including the Real Time Counter clock source are stopped. This
only allows operation of asynchronous modules that does not require a running clock. The only
interrupts that can wake up the MCU are the Two Wire Interface address match interrupt, asynchronous port interrupts and USB resume interrupt.
11.3.3
Power-save Mode
Power-save mode is identical to Power-down, with one exception, if the Real Time Counter
(RTC) is enabled, it will keep running during sleep and the device can also wake up from either
RTC Overflow or Compare Match interrupt.
21
8387A–AVR–07/11
XMEGA A4U
11.3.4
Standby Mode
Standby mode is identical to Power-down with the exception that the enabled system clock
sources are kept running, while the CPU, Peripheral and RTC clocks are stopped. This reduces
the wake-up time.
11.3.5
Extended Standby Mode
Extended Standby mode is identical to Power-save mode with the exception that the enabled
system clock sources are kept running while the CPU and Peripheral clocks are stopped. This
reduces the wake-up time.
22
8387A–AVR–07/11
XMEGA A4U
12. System Control and Reset
12.1
Features
• Reset the microcontroller and set it to its initial state when a reset source goes active
• Multiple reset sources that cover different situations
– Power-On Reset
– External Reset
– Watchdog Reset
– Brown-Out Reset
– PDI reset
– Software reset
• Asynchronous operation
– No running system clock in the device is required for the reset
• Reset Status Register for reading the reset source from the application code
12.2
Overview
The Reset System issues a microcontroller reset and set the device to its initial state. This is for
situation where operation should not start or continue, for example when the microcontroller
operates below its power supply rating. If a reset source goes active, the device enters and be
kept in reset until all reset sources have released their reset. The I/O pins are immediately
tristated.
The program counter is set to the Reset Vector location and all I/O registers are set to the initial
value. The SRAM content is kept, but not guaranteed.
After reset is released from all reset sources, the default oscillator is started and calibrated
before the device starts running from the Reset Vector address. By default this is the lowest program memory address, '0', but it is possible to move the Reset Vector to the lowest address in
the Boot Section.
The reset functionality is asynchronous, so no running system clock is required to reset the
device. The software reset feature makes it possible to issue a controlled system reset from the
user software.
The reset status register has individual status flags for each reset source. It is cleared at Poweron Reset, it shows which sources that have issued a reset since the last power-on.
12.3
12.3.1
Reset Sources
Power-On Reset
The device is reset when the supply voltage VCC is below the Power-on Reset threshold
voltage.
12.3.2
External Reset
The device is reset when a low level is present on the RESET pin.
12.3.3
Watchdog Reset
The device is reset when the Watchdog Timer period expires and the Watchdog Reset is
enabled. The Watchdog Timer runs from a dedicated oscillator independent of the System
Clock. For more details see ”WDT - Watchdog Timer” on page 25.
23
8387A–AVR–07/11
XMEGA A4U
12.3.4
Brown-Out Reset
The device is reset when the supply voltage VCC is below the Brown-Out Reset threshold voltage and the Brown-out Detector is enabled. The Brown-out threshold voltage is programmable.
12.3.5
PDI reset
The MCU can be reset through the Program and Debug Interface (PDI).
12.3.6
Software reset
The MCU can be reset by the CPU writing to a special I/O register through a timed sequence.
24
8387A–AVR–07/11
XMEGA A4U
13. WDT - Watchdog Timer
13.0.1
Features
• Issues a device reset if the timer is not reset before its timeout period
• Asynchronously operation from dedicated oscillator
– 1kHz output of the 32kHz Ultra Low Power oscillator
• 11 selectable timeout periods, from 8ms to 8s.
• Two operation modes
– Normal mode
– Window mode
• Configuration lock to prevent unwanted changes
13.1
Overview
The Watchdog Timer (WDT) is a system function for monitoring correct program operation. It
makes it possible to recover from error situations such as run-away or dead-lock code. The WDT
is a timer, configured to a predefined timeout period and is constantly running when enabled. If
the WDT is not reset within the timeout period, it will issue a microcontroller reset. The WDT is
reset by executing the WDR (Watchdog Timer Reset) instruction from the application code.
The window mode makes it possible to define a time slot window inside the total timeout period
where WDT must be reset within. If the WDT is reset too early or too late and outside this window, a system reset will be issued. Compared to the normal mode, this can also catch situations
where a code error also causes constant WDR execution.
The WDT will run in Active mode and all sleep modes if enabled. It is asynchronous and runs
from a CPU independent clock source, and will continue to operate to issue a system reset even
if the main clocks fail. The Configuration Change Protection mechanism ensures that the WDT
settings cannot be changed by accident. For increased safety, a fuse for locking the WDT settings is available.
25
8387A–AVR–07/11
XMEGA A4U
14. Interrupts and Programmable Multi-level Interrupt Controller
14.1
Features
• Short and predictable interrupt response time
• Separate interrupt configuration and vector address for each interrupt
• Programmable Multi-level Interrupt Controller
– Interrupt prioritizing according to level and vector address
– 3 selectable interrupt levels for all interrupts: Low, Medium and High
– Selectable round-robin priority scheme within low level interrupts
– Non-Maskable Interrupts for critical functions
• Interrupt vectors can be moved from the Application Section to the Boot Loader Section
14.2
Overview
Atmel® AVR® XMEGA® have a Programmable Multi-level Interrupt Controller (PMIC). Interrupts
signal a change of state in peripherals, and this can be used to alter program execution. Peripherals can have one or more interrupts, and all are individually enabled and configured. When an
interrupt is enabled and configured, it will generate an interrupt request when the interrupt condition is present. The Programmable Multi-level Interrupt Controller (PMIC) controls the handling
and prioritizing of interrupt requests. When an interrupt request is acknowledged by the PMIC,
the program counter is set to point to the interrupt vector, and the interrupt handler can be
executed.
All peripherals can select between three different priority levels for their interrupts; low, medium
and high. Interrupts are prioritized according to their level and their interrupt vector address.
Medium level interrupts will interrupt low level interrupt handlers. High level interrupts will interrupt both medium and low level interrupt handlers. Within each level, the interrupt priority is
decided from the interrupt vector address, where the lowest interrupt vector address has the
highest interrupt priority. Low level interrupts have an optional round-robin scheduling scheme to
ensure that all interrupts are serviced within a certain amount of time.
Non-Maskable Interrupts (NMI) is also supported and can be used for critical functions. If a bootloader is used, it is possible to move the interrupt vectors from the Application Section to the
Boot Loader Sections so interrupts can be used and executed also during self-programming.
14.3
Interrupt vectors
The interrupt vector is the sum of the peripheral’s base interrupt address and the offset address
for specific interrupts in each peripheral. The base addresses for the XMEGA A4U devices are
shown in Table 14-1 on page 27. Offset addresses for each interrupt available in the peripheral
are described for each peripheral in the XMEGA AU manual. For peripherals or modules that
have only one interrupt, the interrupt vector is shown in Table 14-1 on page 27. The program
address is the word address.
26
8387A–AVR–07/11
XMEGA A4U
Table 14-1.
Reset and Interrupt Vectors
Program Address
(Base Address)
Source
0x000
RESET
0x002
OSCF_INT_vect
Crystal Oscillator Failure Interrupt vector (NMI)
0x004
PORTC_INT_base
Port C Interrupt base
0x008
PORTR_INT_base
Port R Interrupt base
0x00C
DMA_INT_base
DMA Controller Interrupt base
0x014
RTC_INT_base
Real Time Counter Interrupt base
0x018
TWIC_INT_base
Two-Wire Interface on Port C Interrupt base
0x01C
TCC0_INT_base
Timer/Counter 0 on port C Interrupt base
0x028
TCC1_INT_base
Timer/Counter 1 on port C Interrupt base
0x030
SPIC_INT_vect
SPI on port C Interrupt vector
0x032
USARTC0_INT_base
USART 0 on port C Interrupt base
0x038
USARTC1_INT_base
USART 1 on port C Interrupt base
0x03E
AES_INT_vect
AES Interrupt vector
0x040
NVM_INT_base
Non-Volatile Memory Interrupt base
0x044
PORTB_INT_base
Port B Interrupt base
0x056
PORTE_INT_base
Port E Interrupt base
0x05A
TWIE_INT_base
Two-Wire Interface on Port E Interrupt base
0x05E
TCE0_INT_base
Timer/Counter 0 on port E Interrupt base
0x06A
TCE1_INT_base
Timer/Counter 1 on port E Interrupt base
0x074
USARTE0_INT_base
USART 0 on port E Interrupt base
0x080
PORTD_INT_base
Port D Interrupt base
0x084
PORTA_INT_base
Port A Interrupt base
0x088
ACA_INT_base
Analog Comparator on Port A Interrupt base
0x08E
ADCA_INT_base
Analog to Digital Converter on Port A Interrupt base
0x09A
TCD0_INT_base
Timer/Counter 0 on port D Interrupt base
0x0A6
TCD1_INT_base
Timer/Counter 1 on port D Interrupt base
0x0AE
SPID_INT_vector
SPI on port D Interrupt vector
0x0B0
USARTD0_INT_base
USART 0 on port D Interrupt base
0x0B6
USARTD1_INT_base
USART 1 on port D Interrupt base
0x0FA
USB_INT_base
USB on port D Interrupt base
Interrupt Description
27
8387A–AVR–07/11
XMEGA A4U
15. I/O Ports
15.1
Features
• General purpose input and output pins with several and individual configuration options
• Output driver with configurable driver and pull settings:
•
•
•
•
•
•
•
•
•
•
15.2
– Totem-pole
– Wired-AND
– Wired-OR
– Bus-keeper
– Inverted I/O
Input with synchronous and/or asynchronous sensing with port interrupts and events
– Sense both edges
– Sense rising edges
– Sense falling edges
– Sense low level
Optimal pull-up and pull-down resistor on input and Wired-OR/AND configurations
Optional slew rate control
Asynchronous pin change sensing that can wake-up the device from all sleep modes
Two port interrupts with pin masking per I/O port
Efficient and safe access to port pins
– Hardware read-modify-write through dedicated Toggle/Clear/Set registers
– Configuration of multiple pins in a single operation
– Mapping of port registers into bit-accessible I/O memory space
Peripheral Clocks output on port pin
Real Time Counter Clock output to port pin
Event Channel output on port pin
Remap of digital peripheral pin functions
– Selectable USART, SPI and Timer/Counter input/output pin locations
Overview
One port consists of up to 8 pins ranging from pin 0 to 7. Each port pin can be configured as
input or output with configurable driver and pull settings. They also implement synchronous and
asynchronous input sensing with interrupts and events for selectable pin change conditions.
Asynchronous pin-change sensing means that a pin change can wake the device from all sleep
modes, included the modes where no clocks are running.
All functions are individual and configurable per pin, but several pins can be configured in one
single operation. The pins have hardware Read-Modify-Write (RMW) functionality for safe and
correct change of drive value and/or pull resistor configuration. The direction of one port pin can
be changed without unintentionally changing the direction of any other pin.
The port pin configuration also controls input and output selection of other device function. It is
possible to have both the peripheral clock and the real time clock output to a port pin, and available for external use. The same applies to events from the Event System that can be used to
synchronize and control external functions. Other digital peripherals such as USART, SPI and
Timer/Counters can be remapped to selectable pin location in order to optimize pinout versus
application needs.
28
8387A–AVR–07/11
XMEGA A4U
15.3
Output Driver
All port pins (Pn) have programmable output configuration. The port pins also have configurable
slew rate limitation to reduce electromagnetic emission.
15.3.1
Push-pull
Figure 15-1. I/O configuration - Totem-pole
DIRn
OUTn
Pn
INn
15.3.2
Pull-down
Figure 15-2. I/O configuration - Totem-pole with pull-down (on input)
DIRn
OUTn
Pn
INn
15.3.3
Pull-up
Figure 15-3. I/O configuration - Totem-pole with pull-up (on input)
DIRn
OUTn
Pn
INn
29
8387A–AVR–07/11
XMEGA A4U
15.3.4
Bus-keeper
The bus-keeper’s weak output produces the same logical level as the last output level. It acts as
a pull-up if the last level was ‘1’, and pull-down if the last level was ‘0’.
Figure 15-4. I/O configuration - Totem-pole with bus-keeper
DIRn
OUTn
Pn
INn
15.3.5
Others
Figure 15-5. Output configuration - Wired-OR with optional pull-down
OUTn
Pn
INn
Figure 15-6. I/O configuration - Wired-AND with optional pull-up
INn
Pn
OUTn
30
8387A–AVR–07/11
XMEGA A4U
15.4
Input sensing
Input sensing is synchronous or asynchronous depending on the enabled clock for the ports,
and the configuration is shown in Figure 15-7 on page 31.
Figure 15-7. Input sensing system overview
Asynchronous sensing
EDGE
DETECT
Interrupt
Control
IREQ
Synchronous sensing
Pn
Synchronizer
INn
Q D
D
INVERTED I/O
R
Q
EDGE
DETECT
Event
R
When a pin is configured with inverted I/O, the pin value is inverted before the input sensing.
15.5
Alternate Port Functions
In addition to the input/output functions on all port pins, most pins have alternate functions. This
means that other modules or peripherals connected to the port can use the port pins for their
functions, such as communication or pulse-width modulation. ”Pinout and Pin Functions” on
page 51 shows which modules on peripherals that enable alternate functions on a pin, and
which alternate function is available on a pin.
31
8387A–AVR–07/11
XMEGA A4U
16. T/C - 16-bit Timer/Counter
16.1
Features
• Five 16-bit Timer/Counters
•
•
•
•
•
•
•
•
•
•
•
•
•
16.2
– Three Timer/Counters of type 0
– Two Timer/Counters of type 1
32-bit Timer/Counter support by cascading two Timer/Counters
Up to 3 Compare or Capture (CC) Channels
– 3 CC Channels for Timer/Counter of type 0
– 2 CC Channels for Timer/Counter of type 1
Double Buffered Timer Period Setting
Double Buffered Compare or Capture Channels
Waveform Generation:
– Frequency Generation
– Single Slope Pulse Width Modulation
– Dual Slope Pulse Width Modulation
Input Capture:
– Input Capture with noise cancelling
– Frequency capture
– Pulse width capture
– 32-bit input capture
Timer Overflow and Error interrupts / events
One Compare Match or Input Capture interrupt / event per CC Channel
Can be used with Event System for
– Quadrature Decoding
– Count and direction control
– Capture
Can be used with DMA and trigger DMA transactions
High-Resolution Extension
– Increases frequency and waveform resolution by 4x (2-bit), or 8x (3-bit)
Advanced Waveform Extension
– Low and High-side output with programmable Dead-Time Insertion (DTI)
Event controlled fault protection for safe disabling of external drivers
Overview
There are five flexible 16-bit Timer/Counters (TC). Their capabilities include accurate program
execution timing, frequency and waveform generation, and input capture with time and frequency measurement of digital signals. Two Timer/Counters can be cascaded to create 32-bit
Timer/Counter with optional 32-bit capture.
A Timer/Counter consists of a Base Counter and a set of Compare or Capture (CC) channels.
The Base Counter can be used to count clock cycles or events. It has direction control and
period setting that can be used for timing. The CC channels can be used together with the Base
Counter to do compare match control, frequency generation and pulse width waveform modulation, or various input capture operations. A Timer/Counter can be configured for either capture or
compare functions, and not perform both at the same time.
A Timer/Counter can be clocked and timed from the Peripheral Clock with optional prescaling or
the Event System. The Event System can also be used for direction control, capture trigger or to
synchronize operations.
32
8387A–AVR–07/11
XMEGA A4U
Figure 16-1. Overview of a Timer/Counter and closely related peripherals
Timer/Counter
Base Counter
Timer Period
Counter
Prescaler
Control Logic
clkPER
Event
System
clkPER4
Buffer
Capture
Control
Waveform
Generation
Dead-Time
Insertion
Pattern
Generation
Fault
Protection
PORT
Comparator
AWeX
Hi-Res
Compare/Capture Channel D
Compare/Capture Channel C
Compare/Capture Channel B
Compare/Capture Channel A
The only difference between Timer/Counter type 0 and 1 is the number of CC Channels.
Timer/Counter 0 has four CC channels, and Timer/Counter 1 has two CC channels. All information related to CC channel 3 and 4 is only valid for Timer/Counter 0.
Some Timer/Counters have extensions to enable more specialized waveform and frequency
generation. The Advanced Waveform Extension (AWeX) is intended for motor control and other
power control applications. It enables Low- and High Side output with Dead Time Insertion, and
fault protection for disabling and shutdown of drivers. It can also generate a synchronized bit
pattern across the port pins.See ”Hi-Res - High Resolution Extension” on page 35 for more
details.
The High Resolution (Hi-Res) extension can be used to increase the waveform output resolution
by up to eight times, by using internal clock source running up to four times faster than the
Peripheral Clock. See ”AWeX - Advanced Waveform Extension” on page 34 for more details.
PORTC and PORTD each has one Timer/Counter 0 and one Timer/Counter1. PORTE has one
Timer/Conter0. Notation of these are TCC0 (Time/Counter C0), TCC1, TCD0, TCD1 and TCE0,
respectively.
33
8387A–AVR–07/11
XMEGA A4U
17. AWeX - Advanced Waveform Extension
17.1
Features
• Wafeform output with complementary output from each Compare channel
• 4 Dead-Time Insertion (DTI) Units
– 8-bit Resolution
– Separate High and Low Side Dead-Time Setting
– Double Buffered Dead-Time
– Optionally halts Timer during Dead-Time Insertion
• Pattern Generation unit creating synchronised bit pattern across the port pins
– Double buffered pattern generation
– Optionally distribution of one Compare channel output across the port pins
• Event controlled Fault Protection for instant and predictably fault triggering
17.2
Overview
The Advanced Waveform Extension (AWeX) provides extra functions to the Timer/Counter in
Waveform Generation (WG) modes. It is primarily intended for different types of motor control
and other power control applications. It enables Low- and High Side output with Dead Time
Insertion, and fault protection for disabling and shutdown of drivers. It can also generate a synchronized bit pattern across the port pins.
Each of the waveform generator outputs from the Timer/Counter 0 are split into a complimentary
pair of outputs when any AWeX features are enabled. These output pairs go through a DeadTime Insertion (DTI) unit that generates the non-inverted Low Side (LS) and inverted High Side
(HS) of the WG output with dead time insertion between LS and HS switching. The DTI output
will override the normal port value according to the port override setting.
The Pattern Generation unit can be used to generate a synchronized bit pattern across the port
it is connected to. In addition, the WG output from the Compare Channel A can be distributed to
and override all the port pins. When the Pattern Generator unit is enabled the DTI unit is
bypassed.
The Fault Protection unit is connected to the Event System, enabling any event to trigger a fault
condition that will disable the AWeX output. The Event System ensure predictable and instant
fault reaction, and gives great flexibility in the selection of fault triggers.
The AWEX is available for TCC0. The notation of this is AWEXC.
34
8387A–AVR–07/11
XMEGA A4U
18. Hi-Res - High Resolution Extension
18.1
Features
• Increases Waveform Generator resolution by up to 8 times (3-bit)
• Supports Frequency, Single Slope PWM and Dual Slope PWM generation
• Supports the AWeX when this is used for the same Timer/Counter
18.2
Overview
The Hi-Resolution (Hi-Res) Extension is able to increase the resolution of the waveform generation output by a factor of four or eight. It can be used for a Timer/Counter doing Frequency,
Single Slope PWM or Dual Slope PWM generation. It can also be used with the AWeX if this is
used for the same Timer/Counter.
Atmel® AVR® XMEGA® A4U have three Hi-Res Extensions that each can be enabled for each
Timer/Counters pair on PORTC, PORTD and PORTE. The notation of these are HIRESC,
HIRESD and HIRESE, respectively.
35
8387A–AVR–07/11
XMEGA A4U
19. RTC - 16-bit Real-Time Counter
19.1
Features
• 16-bit resolution
• Selectable clock source
•
•
•
•
•
19.2
– 32.768kHz external crystal
– External clock
– 32.768kHz internal oscillator
– 32kHz internal ULP oscillator
Programmable 10-bit clock prescaling
One Compare register
One Period register
Clear Counter on period overflow
Optional Interrupt/ Event on overflow and compare match
Overview
The 16-bit Real Time Counter (RTC) is a counter that typically runs continuously, including in
low power sleep modes, to keep track of time. It can wake up the device from sleep modes
and/or interrupt the device at regular intervals.
The reference clock is typically the 1.024kHz output from a high accuracy crystal of 32.768kHz,
and this is the configuration most optimized for low power consumption. The faster 32.768kHz
output can be selected if the RTC needs a higher resolution than 1mS. The RTC can also be
clocked from an external clock signal, the internal 32.768kHz oscillator or the internal 32kHz
ULP oscillator.
The RTC includes a 10-bit programmable prescaler that can scale down the reference clock
before it reaches the Counter. A wide range of resolution and time-out periods can be configured. With a 32.768kHz clock source the maximum resolution of 30.5µs, time-out periods range
up to 2000seconds. With a resolution of 1 second, the maximum time-out period is over 18hours
(65536seconds). The RTC can give a compare interrupt and/or event when the counter equals
the Compare register value, and an overflow interrupt and/event when it equals the Period register value.
Figure 19-1. Real Time Counter overview
External Clock
TOSC1
TOSC2
32.768kHz Crystal Osc
32.768kHz Int. Osc
DIV32
DIV32
32kHz int ULP (DIV32)
PER
RTCSRC
clkRTC
10-bit
prescaler
=
TOP/
Overflow
=
”match”/
Compare
CNT
COMP
36
8387A–AVR–07/11
XMEGA A4U
20. USB - Universal Serial Bus Interface
20.1
Features
• One USB 2.0 full speed (12Mbps) and low speed (1.5Mbps) device compliant interface
• Integrated on-chip USB transceiver, no external components needed
• 16 endpoint addresses with full endpoint flexibility for up to 32 endpoints
•
•
•
•
•
•
•
•
•
•
20.2
– One input endpoint per endpoint address
– One output endpoint per endpoint address
Endpoint address transfer type selectable to
– Control transfers
– Interrupt transfers
– Bulk transfers
– Isochronous transfers
Configurable data payload size per endpoint, up to 1023bytes
Endpoint configuration and data buffers located in internal SRAM
– Configurable location for endpoint configuration data
– Configurable location for each endpoint's data buffer
Built in Direct Memory Access (DMA) to internal SRAM for
– Endpoint configurations
– Read and write of endpoint data
Ping-Pong operation for higher throughput and double buffered operation
– Input and output endpoint data buffers used in a single direction
– CPU/DMA controller can update data buffer during transfer
Multi-Packet transfer for reduced interrupt load and software intervention
– Data payload exceeding max packet size is transferred in one continuous transfer
– No interrupts or software interaction on packet transaction level
Transaction Complete FIFO for easy flow management when using multiple endpoints
– Tracks all completed transactions in a first come, first serve work-queue
Clock selection independent of System Clock source selection
Connection to Event System
On chip debug possibilities during USB transactions
Overview
The USB interface is an USB 2.0 full speed (12Mbps) and low speed (1.5Mbps) device compliant interface.
It supports 16 endpoint addresses. All endpoint addresses have one input and one output endpoint, for a total of 32 endpoints. Each endpoint address is fully configurable and can be
configured for any of the four transfer types: control, interrupt, bulk or isochronous. The data
payload size is also selectable and it supports data payloads up to 1023bytes.
No dedicated memory is allocated for or included in the USB module. Internal SRAM is used to
keep the configuration for each endpoint address, and the data buffer for each endpoint. The
memory locations used for endpoint configurations and data buffers are fully configurable. The
amount of memory allocated is fully dynamic according to the number of endpoints in use, and
the configuration of these. The USB module has built-in Direct Memory Access (DMA) and will
read/write data from/to the SRAM when a USB transaction takes place.
To maximise throughput, an endpoint address can be configured for Ping-Pong operation. When
this is done, the input and output endpoints are both used in the same direction. The CPU or
37
8387A–AVR–07/11
XMEGA A4U
DMA Controller can then read/write one data buffer while the USB module writes/reads the
other, and vice versa. This gives double buffered communication.
Multi-packet transfer enables a data payload exceeding the maximum packet size of an endpointto be transferred as multiple packets without software intervention. This reduce the CPU
intervention and the interrupts needed for USB transfers.
For low power operation, the USB module can put the microcontroller in any sleep mode when
the USB bus is idle and a suspend condition is given. Upon bus resume, the USB module can
wake the microcontroller from any sleep mode.
PORTD has one USB. Notation of this is USB.
38
8387A–AVR–07/11
XMEGA A4U
21. TWI - Two Wire Interface
21.1
Features
• Two Identical Two Wire Interface peripherals
• Bi-directional two-wire communication interface
•
•
•
•
•
•
•
•
•
21.2
– Phillips I2C compatible
– System Management Bus (SMBus) compatible
Bus master and slave operation supported
– Slave operation
– Single bus master operation
– Bus master in multi-master bus environment
– Multi-master arbitration
Flexible slave address match functions
– 7-bit and General Call Address Recognition in Hardware
– 10-bit addressing supported
– Address mask register for dual address match or address range masking
– Optional software address recognition for unlimited number of addresses
Slave can operate in all sleep modes
Slave address match can wake device from all sleep modes
100kHz and 400kHz bus frequency support
Slew-rate limited output drivers
Input filter for bus noise and spike suppression
Support arbitration between START/Repeated START and Data Bit (SMBus)
Slave arbitration allows support for Address Resolve Protocol (ARP) (SMBus)
Overview
The Two Wire Interface is a bi-directional two-wire communication interface. It is I2C and System
Management Bus (SMBus) compatible. The only external hardware needed to implement the
bus is one pull-up resistor on each bus line.
The TWI module supports master and slave functionality. The master and slave functionality are
separated from each other and can be enabled and configured separately. The master module
supports multi-master bus operation and arbitration. It contains the baud rate generator. Both
100kHz and 400kHz bus frequency is supported.
The slave module implements 7-bit address match and general address call recognition in hardware. 10-bit addressing is also supported. A dedicated address mask register can act as a
second address match register or as a register for address range masking. The slave continues
to operate in all sleep modes, including Power down mode. This enables the slave to wake up
the device from all sleep modes on TWI address match. It is possible to disable the address
matching to let this be handled in software instead. Smart Mode can be enabled to auto trigger
operations and reduce software complexity.
The TWI module will detect START and STOP conditions, bus collision and bus errors. Arbitration lost, errors, collision and clock hold on the bus is also detected and indicated in separate
status flags available in both master and slave mode.
It is possible to disable the TWI drivers in the device, and enable a 4-wire digital interface for
connecting to an external TWI bus driver. This can be used for applications where the device
operates from a different VCC voltage than used by the TWI bus.
PORTC and PORTE each has one TWI. Notation of these peripherals are TWIC and TWIE,
respectively.
39
8387A–AVR–07/11
XMEGA A4U
22. SPI - Serial Peripheral Interface
22.1
Features
•
•
•
•
•
•
•
•
•
22.2
Two Identical SPI peripherals
Full-duplex, Three-wire Synchronous Data Transfer
Master or Slave Operation
LSB First or MSB First Data Transfer
Seven Programmable Bit Rates
Interrupt Flag at the End of Transmission
Write collision flag to indicate data collision
Wake-up from Idle Mode
Double Speed Master Mode
Overview
The Serial Peripheral Interface (SPI) is a high-speed synchronous data transfer interface using
three or four pins. It allows fast communication between an XMEGA device and peripheral
devices or other microcontrollers. The SPI supports full duplex communication.
A device connected to the bus must act as a master or slave. The master initiates and controls
all data transactions, and data is transferred both to and from the device simultaneously.
PORTC and PORTD each has one SPI. Notation of these peripherals are SPIC and SPID,
respectively.
40
8387A–AVR–07/11
XMEGA A4U
23. USART
23.1
Features
• Five Identical USART peripherals
• Full Duplex Operation
• Asynchronous or Synchronous Operation
•
•
•
•
•
•
•
23.2
– Synchronous clock rates up to 1/2 o the device clock frequency
– Asynchronous clock rates up to 1/8 of the device clock frequency
Supports Serial Frames with 5, 6, 7, 8, or 9 Data Bits and 1 or 2 Stop Bits
Fractional Baud Rate Generator
– Can generate desired baud rate from any system clock frequency
– No need for external oscillator with certain frequencies
Built in error detection and correction schemes
– Odd or Even Parity Generation and Parity Check
– Data Over Run and Framing Error Detection
– Noise Filtering Includes False Start Bit Detection and Digital Low Pass Filter
Separate Interrupts for
– Transmit Complete
– Transmit Data Register Empty
– Receive Complete
Multi-Processor Communication Mode
– Addressing scheme to address a specific devices on a multi-device bus
– Enable unaddressed devices to automatically ignore all frames
Master SPI Mode
– Double Buffered Operation
– Configurable Data Order
– High Speed Operation up to 1/2 of the peripheral clock frequency
IRCOM Module for IrDA compliant pulse modulation/demodulation
Overview
The Universal Synchronous and Asynchronous serial Receiver and Transmitter (USART) is a
fast and flexible serial communication module. The USART supports full duplex communication,
and both asynchronous and clocked synchronous operation. The USART can also be set in
Master SPI mode and be used for SPI communication.
Communication is frame based, and the frame format can be customized to support a wide
range of standards. The USART is buffered in both direction, enabling continued data transmission without any delay between frames. There are separate interrupts for receive and transmit
complete, enabling fully interrupt driven communication. Frame error and buffer overflow are
detected in hardware and indicated with separate status flags. Even or odd parity generation
and parity check can also be enabled.
The Clock Generation logic has a fractional baud rate generator that is able to generate a wide
range of USART baud rates from any system clock frequencies. This remove the need to use
an external crystal oscillator with a certain frequency in order to achieve a required baud rate. It
also includes support external clock input in synchronous slave operation.
One USART can use the IRCOM module to support IrDA 1.4 physical compliant pulse modulation and demodulation for baud rates up to 115.2kbps.
PORTC and PORTD each has two USARTs. PORTE has one USART. Notation of these peripherals are USARTC0, USARTC1, USARTD0, USARTD1 and USARTE0, respectively.
41
8387A–AVR–07/11
XMEGA A4U
24. IRCOM - IR Communication Module
24.1
Features
• Pulse modulation/demodulation for infrared communication
• IrDA Compatible for baud rates up to 115.2kbps
• Selectable pulse modulation scheme
– 3/16 of baud rate period
– Fixed pulse period, 8-bit programmable
– Pulse modulation disabled
• Built in filtering
• Can be connected to and used by one USART at a time
24.2
Overview
The Infrared Communication Module (IRCOM) is used for IrDA communication with baud rates
up to 115.2kbps. There is one IRCOM available which can be connected to any USART to
enable infrared pulse coding/decoding for that USART.
42
8387A–AVR–07/11
XMEGA A4U
25. AES and DES Crypto Engine
25.1
Features
• Data Encryption Standard (DES) CPU instruction
• Advanced Encryption Standard (AES) Crypto module
• DES Instruction
– Encryption and Decryption
– Single-cycle DES instruction
– Encryption/Decryption in 16 clock cycles per 8-byte block
• AES Crypto Module
– Encryption and Decryption
– Supports 128-bit keys
– Supports XOR data load mode to the State memory for Cipher Block Chaining
– Encryption/Decryption in 375 clock cycles per 16-byte block
25.2
Overview
The Advanced Encryption Standard (AES) and Data Encryption Standard (DES) are two commonly used standards for cryptography. These are supported through an AES peripheral
module and a DES CPU instruction, and the communication interfaces and the CPU can use
these for fast encrypted communication and secure data storage.
DES is supported by an instruction in the AVR CPU. The 8-byte key and 8-byte data blocks must
be loaded into the Register file, and then the DES instruction must be executed 16 times to
encrypt/decrypt the data block.
The AES Crypto Module encrypts and decrypts 128-bit data blocks with the use of a 128-bit key.
The key and data must be loaded into the key and state memory in the module before encryption/ decryption is started. It takes 375 Peripheral clock cycles before the encryption/decryption
is done. The encrypted/encrypted data can then be read out, and an optional interrupt can be
generated. The AES Crypto Module also has DMA support with transfer triggers when encryption/decryption is done and optional auto-start of encryption/decryption when the state memory
is fully loaded.
43
8387A–AVR–07/11
XMEGA A4U
26. CRC - Cyclic Redundancy Check Generator
26.1
Features
• Cyclic Redundancy Check (CRC) Generation and Checking for
– Communication Data
– Program or Data in Flash memory
– Data in SRAM memory and I/O memory space
• Integrated with Flash memory, DMA Controller and CPU
– Continuous CRC on data going through a DMA Channel
– Automatic CRC of the complete, or selectable range of the Flash memory
– CPU can load data to CRC Generator through I/O interface
• CRC polynomial software selectable to
– CRC-16 (CRC-CCITT)
– CRC-32 (IEEE 802.3)
• Zero remainder detection
26.2
Overview
A Cyclic Redundancy Check (CRC) is a test algorithm used to detect accidental errors on data,
and is commonly used to determine the correctness of a data transmission, data memory and
program memory. A CRC takes a data stream or block of data as input and generates a 16- or
32-bit output that can be kept with the data and used as checksum. When the same data is later
received or read, the device or application repeats the calculation. If the new CRC calculation
does not match the one calculated earlier, the block contains a data error. The application will
then detect this and may take corrective action such as requesting the data to be sent again.
Typically, an n-bit CRC, applied to a data block of arbitrary length, will detect any single error
burst not longer than n bits (in other words, any single alteration that spans no more than n bits
of the data), and will detect a fraction 1-2-n of all longer error bursts.The CRC module in XMEGA
supports two commonly used CRC polynomials; CRC-16 (CRC-CCITT) and CRC-32
(IEEE 802.3).
• CRC-16:
Polynomial:
x16+x12+x5+1
Hex value:
0x1021
• CRC-32:
Polynomial:
x32+x26+x23+x22+x16+x12+x11+x10+x8+x7+x5+x4+x2+x+1
Hex value:
0x04C11DB7
44
8387A–AVR–07/11
XMEGA A4U
27. ADC - 12-bit Analog to Digital Converter
27.1
Features
• One Analog to Digital Converter (ADC)
• 12-bit resolution
• Up to 2Million Samples Per Second
•
•
•
•
•
•
•
•
•
•
27.2
– 4 inputs can be sampled within 1.5µs
– Down to 2.5µs conversion time with 8-bit resolution
– Down to 3.5µs conversion time with 12-bit resolution
Differential and Single-ended input
– Up to 16 single-ended inputs
– 16x4 differential inputs without gain
– 16x4 differential input with gain
Built in differential gain stage
– 1/2x, 1x, 2x, 4x, 8x, 16x, 32x and 64x gain options
Single, continues and scan conversion options
4 internal inputs
– Internal Temperature sensor
– DAC Output
– VCC voltage divided by 10
– 1.1V Bandgap voltage
4 conversion channels with individual input control and result registers
– Enable 4 parallel configurations and results
Internal and external reference options
Compare function for accurate monitoring of user defined thresholds
Optional event triggered conversion for accurate timing
Optional DMA transfer of conversion results
Optional interrupt/event on compare result
Overview
The Analog to Digital Converter (ADC) converts analog signals to digital values. The ADC has
12-bit resolution and is capable of converting up to 2 Million Samples Per Second (MSPS). The
input selection is flexible, and both single-ended and differential measurements can be done.
For differential measurements an optional gain stage is available to increase the dynamic range.
In addition several internal signal inputs are available. The ADC can provide both signed and
unsigned results.
This is a pipelined ADC that consists of several consecutive stages. The pipelined design allows
high sample rate at a low System Clock frequency. It also means that a new input can be sampled and a new ADC conversion started while other ADC conversions are still ongoing. This
remove dependencies between sample rate and propagation delay.
The ADC has four conversion channels (Channel 0-3) with individual input selection, result registers and conversion start control. The ADC can then keep and use four parallel configurations
and results, and this will ease use for applications with high data throughput or multiple modules
using the ADC independently. It is possible to use DMA to move ADC results directly to memory
or peripherals when conversions are done.
45
8387A–AVR–07/11
XMEGA A4U
Both internal and external reference voltages can be used. An integrated temperature sensor is
available for use with the ADC. The output from the DAC, VCC/10 and the Bandgap voltage can
also be measured by the ADC.
The ADC has a compare function for accurate monitoring of user defined thresholds with minimum software intervention required.
Figure 27-1. ADC overview
ADC0
•
•
•
ADC15
ADC4
•
•
•
ADC7
Int. signals
ADC0
•
•
•
ADC3
Int. signals
Compare
Register
Internal
signals
VINP
ADC
½x - 64x
Internal
signals
CH0 Result
CH1 Result
Threshold
(Int Req)
CH2 Result
CH3 Result
VINN
Internal 1.00V
Internal VCC/1.6V
Internal VCC/2
AREFA
AREFB
<
>
Reference
Voltage
Four inputs can be sampled within 1.5µs without any intervention by the application.
The ADC may be configured for 8- or 12-bit result, reducing the minimum conversion time (propagation delay) from 3.5µs for 12-bit to 2.5µs for 8-bit result.
ADC conversion results are provided left- or right adjusted with optional ‘1’ or ‘0’ padding. This
eases calculation when the result is represented as a signed integer (signed 16-bit number).
PORTA has one ADC. Notation of this peripheral is ADCA.
46
8387A–AVR–07/11
XMEGA A4U
28. DAC - 12-bit Digital to Analog Converter
28.1
Features
•
•
•
•
•
•
•
•
•
•
•
28.2
One Digital to Analog Converter (DAC)
12-bit resolution
Two independents and continues-time channels per DAC
Up to 1Million Samples Per Second conversion rate per DAC channel
Built in calibration that removes
– Offset error
– Gain error
Multiple conversion trigger sources
– On new available data
– Events from the Event System
High drive capabilities and support for
– Resistive load
– Capacitive load
– Combined resistive and capacitive load
Internal and external reference options
DAC output available as input to Analog Comparator and ADC
Low Power mode with reduced drive strength
Optional DMA transfer of data
Overview
The Digital to Analog Converter (DAC) converts digital values to voltages. The DAC has two
channels, 12-bit resolution, and is capable of converting 1Million Samples Per Second (MSPS)
on each channels. The built-in calibration system can remove offset and gain error when loaded
with calibration values from software.
Figure 28-1. DAC overview
DMA req
(Data Empty)
CH0DATA
12
D
A
T
A
DAC0
Output
Driver
Int.
driver
AVCC
Internal 1.00V
AREFA
AREFB
Reference
selection
12
Select
CTRLB
Trigger
CH1DATA
DMA req
(Data Empty)
Trigger
D
A
T
A
Enable
CTRLA
Select
Enable
DAC1
To
AC/ADC
Internal Output
enable
Output
Driver
A DAC conversion is automatically started when new data to be converted is available. Event
from the Event System can also be used, and this enable synchronized and timed conversions
between the DAC and other peripherals such as a Timer/Counter. The DMA Controller can be
used to transfer data to the DAC.
The DAC has high drive strengths and is capable of driving both resistive and capacitive loads,
and a load which is a combination of this. A low power mode is available, and this will reduce the
drive strengths of the output. Both internal and external voltage reference can be used. The
DAC output is also internally available for use as input to the Analog Comparator or ADC.
PORTB has one DAC. Notation of this peripheral is DACB.
47
8387A–AVR–07/11
XMEGA A4U
29. AC - Analog Comparator
29.1
Features
• Two Analog Comparators
• Selectable propagation delay vs current consumption
• Selectable hysteresis
•
•
•
•
•
29.2
– No
– Small
– Large
Analog Comparator output available on pin
Flexible Input Selection
– All pins on the port
– Output from the DAC
– Bandgap reference voltage.
– A 64-level programmable voltage scaler of the internal VCC voltage
Interrupt and event generation on
– Rising edge
– Falling edge
– Toggle
Window function interrupt and event generation on
– Signal above window
– Signal inside window
– Signal below window
Constant current source with configurable output pin selection
Overview
The Analog Comparator (AC) compares the voltage level on two inputs and gives a digital output
based on this comparison. The Analog Comparator may be configured to give interrupt requests
and/or events upon several different combinations of input change.
Two important properties of the Analog Comparator when it comes to the dynamic behavior, are
hysteresis and propagation delay. Both these parameters may be adjusted in order to find the
optimal operation for each application.
The input section includes analog port pins, several internal signals and a 64-level programmable voltage scaler. The analog comparator output state can also be directly available on a pin for
use by external devices. Using as pair they can also be set in Window mode to monitor a signal
compared to a voltage window instead of a voltage level.
A constant current source can be enabled, and output on a selectable pin. This can be used to
replace for example external resistors used to charge capacitors in capacitive touch sensing
applications.
The Analog Comparators are always grouped in pairs on each port. They have identical behavior but separate control registers.
PORTA has one AC pair. Notation of this peripheral is ACA.
48
8387A–AVR–07/11
XMEGA A4U
Figure 29-1. Analog comparator overview
Pin Input
AC0OUT
Pin Input
Hysteresis
DAC
Voltage
Scaler
Enable
ACnCTRL
ACnMUXCTRL
Interrupt
Mode
WINCTRL
Enable
Bandgap
Interrupt
Sensititivity
Control
&
Window
Function
Interrupts
Events
Hysteresis
Pin Input
AC1OUT
Pin Input
The window function is realized by connecting the external inputs of the two analog comparators
in a pair as shown in Figure 29-2.
Figure 29-2. Analog comparator window function
+
AC0
Upper limit of window
Interrupt
sensitivity
control
Input signal
Interrupts
Events
+
AC1
Lower limit of window
-
49
8387A–AVR–07/11
XMEGA A4U
30. Programming and Debugging
30.1
Features
• Programming
– External programming through the PDI
Minimal protocol overhead for fast operation
Built in error detection and handling for reliable operation
– Bootloader support for programming through any communication interface
• Debugging
– Non-Intrusive Real-Time On-Chip Debug System
– No software or hardware resources required from device expect pin connection
– Program Flow Control
Go, Stop, Reset, Step into, Step over, Step out, Run-to-Cursor
– Unlimited Number of User Program Breakpoints
– Unlimited Number of User Data Breakpoints, break on:
Data location read, write or both read and write
Data location content equal or not equal to a value
Data location content is greater or smaller than a value
Data location content is within or outside a range
– No limitation on device clock frequency
• Program and Debug Interface (PDI)
– 2-pin interface for external programming and debugging
– Uses the Reset pin and a dedicated pin
– No I/O pins required during programming or debugging
30.2
Overview
Atmel® AVR® XMEGA® devices together with Atmel’s development tool chain include the necessary functions for efficient development. All external programming and debugging are done
through the Program and Debug Interface (PDI).
The Program and Debug Interface is 2-pin interface that uses the Reset pin and a dedicated pin.
No I/O pins are required during programming or debugging.
In addition to the PDI, programming can also be done through a bootloader. A bootloader in the
device can use any other communication interface such as UART, TWI or SPI to download and
program new application code to the Flash memory.
Debug is supported through a on-chip debug system that offers Non-Intrusive Real-Time debug.
It does not require any software or hardware resources expect for the device expect pin connection. Using Atmel’s tool chain, it offers complete program flow control and has supported for
unlimited number of program and complex data breakpoints. Application debug can be done
from C and high level language source code level, as well as assembler and disassembler level.
50
8387A–AVR–07/11
XMEGA A4U
31. Pinout and Pin Functions
The device pinout is shown in ”Pinout/Block Diagram” on page 3. In addition to general purpose
I/O functionality, each pin can have several alternate functions. This will depend on which
peripheral is enabled and connected to the actual pin. Only one of the pin functions can be used
at time.
31.1
Alternate Pin Functions Description
The tables below shows the notation and description for all pin functions.
31.1.1
31.1.2
31.1.3
31.1.4
Operation/Power Supply
VCC
Digital supply voltage
AVCC
Analog supply voltage
GND
Ground
Port Interrupt functions
SYNC
Port pin with full synchronous and limited asynchronous interrupt function
ASYNC
Port pin with full synchronous and full asynchronous interrupt function
Analog functions
ACn
Analog Comparator input pin n
ACnOUT
Analog Comparator n Output
ADCn
Analog to Digital Converter input pin n
DACn
Digital to Analog Converter output pin n
AREF
Analog Reference input pin
Timer/Counter and AWeX functions
OCnxLS
Output Compare Channel x Low Side for Timer/Counter n
OCnxHS
Output Compare Channel x High Side for Timer/Counter n
51
8387A–AVR–07/11
XMEGA A4U
31.1.5
31.1.6
31.1.7
Communication functions
SCL
Serial Clock for TWI
SDA
Serial Data for TWI
XCKn
Transfer Clock for USART n
RXDn
Receiver Data for USART n
TXDn
Transmitter Data for USART n
SS
Slave Select for SPI
MOSI
Master Out Slave In for SPI
MISO
Master In Slave Out for SPI
SCK
Serial Clock for SPI
D-
Data- for USB
D+
Data+ for USB
Oscillators, Clock and Event
TOSCn
Timer Oscillator pin n
XTALn
Input/Output for Oscillator pin n
CLKOUT
Peripheral Clock Output
EVOUT
Event Channel 0 Output
RTCOUT
RTC Clock Source Output
Debug/System functions
RESET
Reset pin
PDI_CLK
Program and Debug Interface Clock pin
PDI_DATA
Program and Debug Interface Data pin
52
8387A–AVR–07/11
XMEGA A4U
31.2
Alternate Pin Functions
he tables below show the primary/default function for each pin on a port in the first column, the
pin number in the second column, and then all alternate pin functions in the remaining columns.
The head row shows what peripheral that enable and use the alternate pin functions.
For better flexibility, some alternate functions also have selectable pin locations for their functions, this is noted under the the first table where this apply.
Table 31-1.
PORT A
PIN #
Port A - Alternate functions
INTERRUPT
ADCA
POS/GAINPOS
ADCA
NEG
ADCA
GAINNEG
ACA
POS
ACA
NEG
GND
38
AVCC
39
PA0
40
SYNC
ADC0
ADC0
AC0
AC0
PA1
41
SYNC
ADC1
ADC1
AC1
AC1
PA2
42
SYNC/ASYNC
ADC2
ADC2
AC2
PA3
43
SYNC
ADC3
ADC3
AC3
PA4
44
SYNC
ADC4
ADC4
AC4
PA5
1
SYNC
ADC5
ADC5
AC5
PA6
2
SYNC
ADC6
ADC6
AC6
PA7
3
SYNC
ADC7
ADC7
Table 31-2.
PORT B
ACA
OUT
REFA
AREF
AC3
AC5
AC1OUT
AC7
AC0OUT
Port B - Alternate functions
PIN #
INTERRUPT
ADCA
POS/GAINPOS
DACB
PB0
4
SYNC
ADC8
PB1
5
SYNC
ADC9
PB2
6
SYNC/ASYNC
ADC10
DAC0
PB3
7
SYNC
ADC11
DAC1
REFB
AREF
53
8387A–AVR–07/11
XMEGA A4U
Table 31-3.
PORT C
PIN #
Port C - Alternate functions
INTERRUPT
TCC0(1)
AWEXC
USARTC0(2)
TCC1
SPIC(3)
USARTC1
TWIC
CLOCKOUT(4)
EVENTOUT(5)
GND
8
VCC
9
PC0
10
SYNC
OC0A
OC0ALS
PC1
11
SYNC
OC0B
OC0AHS
XCK0
PC2
12
SYNC/ASYNC
OC0C
OC0BLS
RXD0
PC3
13
SYNC
OC0D
OC0BHS
PC4
14
SYNC
OC0CLS
OC1A
PC5
15
SYNC
OC0CHS
OC1B
XCK1
MOSI
PC6
16
SYNC
OC0DLS
RXD1
MISO
clkRTC
PC7
17
SYNC
OC0DHS
TXD1
SCK
clkPER
EVOUT
CLOCKOUT
EVENTOUT
clkPER
EVOUT
Notes:
1.
2.
3.
4.
5.
SCL
TXD0
SS
Pin mapping of all TC0 can optionally be moved to high nibble of port.
Pin mapping of all USART0 can optionally be moved to high nibble of port.
Pins MOSI and SCK for all SPI can optionally be swapped.
CLKOUT can optionally be moved between port C, D and E and between pin 4 and 7.
EVOUT can optionally be moved between port C, D and E and between pin 4 and 7.
Table 31-4.
PORT D
SDA
PIN #
Port D - Alternate functions
INTERRUPT
TCD0
SYNC
OC0A
TCD1
USBD
USARTD0
USARTD1
SPID
GND
18
VCC
19
PD0
20
PD1
21
SYNC
OC0B
XCK0
PD2
22
SYNC/ASYNC
OC0C
RXD0
PD3
23
SYNC
OC0D
PD4
24
SYNC
OC1A
PD5
25
SYNC
OC1B
XCK1
MOSI
PD6
26
SYNC
D-
RXD1
MISO
PD7
27
SYNC
D+
TXD1
SCK
Table 31-5.
PORT E
TXD0
SS
Port E - Alternate functions
PIN #
INTERRUPT
TCE0
PE0
28
SYNC
OC0A
USARTE0
PE1
29
SYNC
OC0B
XCK0
GND
30
VCC
31
PE2
32
SYNC/ASYNC
OC0C
RXD0
PE3
33
SYNC
OC0D
TXD0
TWIE
SDA
SCL
54
8387A–AVR–07/11
XMEGA A4U
Table 31-6.
PORT R
PIN #
Port R- Alternate functions
INTERRUPT
PDI
PDI
34
PDI_DATA
PDI_CLOCK
XTAL
TOSC(1)
RESET
35
PRO
36
SYNC
XTAL2
TOSC2
PR1
37
SYNC
XTAL1
TOSC1
Note:
1. TOSC pins can optionally be moved to PE2/PE3
55
8387A–AVR–07/11
XMEGA A4U
32. Peripheral Module Address Map
The address maps show the base address for each peripheral and module in XMEGA A4U. For
complete register description and summary for each peripheral module, refer to the XMEGA AU
Manual.
Base Address
0x0000
0x0010
0x0014
0x0018
0x001C
0x0030
0x0040
0x0048
0x0050
0x0060
0x0068
0x0070
0x0078
0x0080
0x0090
0x00A0
0x00B0
0x00C0
0x00D0
0x0100
0x0180
0x01C0
0x0200
0x0240
0x0300
0x0320
0x0380
0x0400
0x0480
0x04A0
0x04C0
0x0600
0x0620
0x0640
0x0660
0x0680
0x07E0
0x0800
0x0840
0x0880
0x0890
0x08A0
0x08B0
0x08C0
0x08F8
0x0900
0x0940
0x0990
0x09A0
0x09B0
0x09C0
0x0A00
0x0A80
0x0A90
0x0AA0
Name
Description
GPIO
VPORT0
VPORT1
VPORT2
VPORT3
CPU
CLK
SLEEP
OSC
DFLLRC32M
DFLLRC2M
PR
RST
WDT
MCU
PMIC
PORTCFG
AES
CRC
DMA
EVSYS
NVM
ADCA
ADCB
DACA
DACB
ACA
RTC
TWIC
TWIE
USB
PORTA
PORTB
PORTC
PORTD
PORTE
PORTR
TCC0
TCC1
AWEXC
HIRESC
USARTC0
USARTC1
SPIC
IRCOM
TCD0
TCD1
HIRESD
USARTD0
USARTD1
SPID
TCE0
AWEXE
HIRESE
USARTE0
General Purpose IO Registers
Virtual Port 0
Virtual Port 1
Virtual Port 2
Virtual Port 3
CPU
Clock Control
Sleep Controller
Oscillator Control
DFLL for the 32MHz Internal Oscillator
DFLL for the 2MHz Internal Oscillator
Power Reduction
Reset Controller
Watch-Dog Timer
MCU Control
Programmable Multilevel Interrupt Controller
Port Configuration
AES Module
CRC Module
DMA Controller
Event System
Non Volatile Memory (NVM) Controller
Analog to Digital Converter on port A
Analog to Digital Converter on port B
Digital to Analog Converter on port A
Digital to Analog Converter on port B
Analog Comparator pair on port A
Real Time Counter
Two Wire Interface on port C
Two Wire Interface on port E
USB Device
Port A
Port B
Port C
Port D
Port E
Port R
Timer/Counter 0 on port C
Timer/Counter 1 on port C
Advanced Waveform Extension on port C
High Resolution Extension on port C
USART 0 on port C
USART 1 on port C
Serial Peripheral Interface on port C
Infrared Communication Module
Timer/Counter 0 on port D
Timer/Counter 1 on port D
High Resolution Extension on port D
USART 0 on port D
USART 1 on port D
Serial Peripheral Interface on port D
Timer/Counter 0 on port E
Advanced Waveform Extension on port E
High Resolution Extension on port E
USART 0 on port E
56
8387A–AVR–07/11
XMEGA A4U
33. Instruction Set Summary
Mnemonics
Operands
Description
Operation
Flags
#Clocks
Arithmetic and Logic Instructions
ADD
Rd, Rr
Add without Carry
Rd
←
Rd + Rr
Z,C,N,V,S,H
1
ADC
Rd, Rr
Add with Carry
Rd
←
Rd + Rr + C
Z,C,N,V,S,H
1
ADIW
Rd, K
Add Immediate to Word
Rd
←
Rd + 1:Rd + K
Z,C,N,V,S
2
SUB
Rd, Rr
Subtract without Carry
Rd
←
Rd - Rr
Z,C,N,V,S,H
1
SUBI
Rd, K
Subtract Immediate
Rd
←
Rd - K
Z,C,N,V,S,H
1
SBC
Rd, Rr
Subtract with Carry
Rd
←
Rd - Rr - C
Z,C,N,V,S,H
1
SBCI
Rd, K
Subtract Immediate with Carry
Rd
←
Rd - K - C
Z,C,N,V,S,H
1
SBIW
Rd, K
Subtract Immediate from Word
Rd + 1:Rd
←
Rd + 1:Rd - K
Z,C,N,V,S
2
AND
Rd, Rr
Logical AND
Rd
←
Rd • Rr
Z,N,V,S
1
ANDI
Rd, K
Logical AND with Immediate
Rd
←
Rd • K
Z,N,V,S
1
OR
Rd, Rr
Logical OR
Rd
←
Rd v Rr
Z,N,V,S
1
ORI
Rd, K
Logical OR with Immediate
Rd
←
Rd v K
Z,N,V,S
1
EOR
Rd, Rr
Exclusive OR
Rd
←
Rd ⊕ Rr
Z,N,V,S
1
COM
Rd
One’s Complement
Rd
←
$FF - Rd
Z,C,N,V,S
1
NEG
Rd
Two’s Complement
Rd
←
$00 - Rd
Z,C,N,V,S,H
1
SBR
Rd,K
Set Bit(s) in Register
Rd
←
Rd v K
Z,N,V,S
1
CBR
Rd,K
Clear Bit(s) in Register
Rd
←
Rd • ($FFh - K)
Z,N,V,S
1
INC
Rd
Increment
Rd
←
Rd + 1
Z,N,V,S
1
DEC
Rd
Decrement
Rd
←
Rd - 1
Z,N,V,S
1
TST
Rd
Test for Zero or Minus
Rd
←
Rd • Rd
Z,N,V,S
1
CLR
Rd
Clear Register
Rd
←
Rd ⊕ Rd
Z,N,V,S
1
SER
Rd
Set Register
Rd
←
$FF
None
1
MUL
Rd,Rr
Multiply Unsigned
R1:R0
←
Rd x Rr (UU)
Z,C
2
MULS
Rd,Rr
Multiply Signed
R1:R0
←
Rd x Rr (SS)
Z,C
2
MULSU
Rd,Rr
Multiply Signed with Unsigned
R1:R0
←
Rd x Rr (SU)
Z,C
2
FMUL
Rd,Rr
Fractional Multiply Unsigned
R1:R0
←
Rd x Rr<<1 (UU)
Z,C
2
FMULS
Rd,Rr
Fractional Multiply Signed
R1:R0
←
Rd x Rr<<1 (SS)
Z,C
2
FMULSU
Rd,Rr
Fractional Multiply Signed with Unsigned
R1:R0
←
Rd x Rr<<1 (SU)
Z,C
2
DES
K
Data Encryption
if (H = 0) then R15:R0
else if (H = 1) then R15:R0
←
←
Encrypt(R15:R0, K)
Decrypt(R15:R0, K)
PC
←
PC + k + 1
None
2
1/2
Branch Instructions
RJMP
k
Relative Jump
IJMP
Indirect Jump to (Z)
PC(15:0)
PC(21:16)
←
←
Z,
0
None
2
EIJMP
Extended Indirect Jump to (Z)
PC(15:0)
PC(21:16)
←
←
Z,
EIND
None
2
JMP
k
Jump
PC
←
k
None
3
RCALL
k
Relative Call Subroutine
PC
←
PC + k + 1
None
2 / 3(1)
ICALL
Indirect Call to (Z)
PC(15:0)
PC(21:16)
←
←
Z,
0
None
2 / 3(1)
EICALL
Extended Indirect Call to (Z)
PC(15:0)
PC(21:16)
←
←
Z,
EIND
None
3(1)
57
8387A–AVR–07/11
XMEGA A4U
Mnemonics
Operands
Description
CALL
k
call Subroutine
PC
←
RET
Subroutine Return
PC
RETI
Interrupt Return
CPSE
Rd,Rr
Compare, Skip if Equal
CP
Rd,Rr
Compare
CPC
Rd,Rr
Compare with Carry
CPI
Rd,K
Compare with Immediate
Operation
Flags
#Clocks
k
None
3 / 4(1)
←
STACK
None
4 / 5(1)
PC
←
STACK
I
4 / 5(1)
if (Rd = Rr) PC
←
PC + 2 or 3
None
1/2/3
Rd - Rr
Z,C,N,V,S,H
1
Rd - Rr - C
Z,C,N,V,S,H
1
Rd - K
Z,C,N,V,S,H
1
SBRC
Rr, b
Skip if Bit in Register Cleared
if (Rr(b) = 0) PC
←
PC + 2 or 3
None
1/2/3
SBRS
Rr, b
Skip if Bit in Register Set
if (Rr(b) = 1) PC
←
PC + 2 or 3
None
1/2/3
SBIC
A, b
Skip if Bit in I/O Register Cleared
if (I/O(A,b) = 0) PC
←
PC + 2 or 3
None
2/3/4
SBIS
A, b
Skip if Bit in I/O Register Set
If (I/O(A,b) =1) PC
←
PC + 2 or 3
None
2/3/4
BRBS
s, k
Branch if Status Flag Set
if (SREG(s) = 1) then PC
←
PC + k + 1
None
1/2
BRBC
s, k
Branch if Status Flag Cleared
if (SREG(s) = 0) then PC
←
PC + k + 1
None
1/2
BREQ
k
Branch if Equal
if (Z = 1) then PC
←
PC + k + 1
None
1/2
BRNE
k
Branch if Not Equal
if (Z = 0) then PC
←
PC + k + 1
None
1/2
BRCS
k
Branch if Carry Set
if (C = 1) then PC
←
PC + k + 1
None
1/2
BRCC
k
Branch if Carry Cleared
if (C = 0) then PC
←
PC + k + 1
None
1/2
BRSH
k
Branch if Same or Higher
if (C = 0) then PC
←
PC + k + 1
None
1/2
BRLO
k
Branch if Lower
if (C = 1) then PC
←
PC + k + 1
None
1/2
BRMI
k
Branch if Minus
if (N = 1) then PC
←
PC + k + 1
None
1/2
BRPL
k
Branch if Plus
if (N = 0) then PC
←
PC + k + 1
None
1/2
BRGE
k
Branch if Greater or Equal, Signed
if (N ⊕ V= 0) then PC
←
PC + k + 1
None
1/2
BRLT
k
Branch if Less Than, Signed
if (N ⊕ V= 1) then PC
←
PC + k + 1
None
1/2
BRHS
k
Branch if Half Carry Flag Set
if (H = 1) then PC
←
PC + k + 1
None
1/2
BRHC
k
Branch if Half Carry Flag Cleared
if (H = 0) then PC
←
PC + k + 1
None
1/2
BRTS
k
Branch if T Flag Set
if (T = 1) then PC
←
PC + k + 1
None
1/2
BRTC
k
Branch if T Flag Cleared
if (T = 0) then PC
←
PC + k + 1
None
1/2
BRVS
k
Branch if Overflow Flag is Set
if (V = 1) then PC
←
PC + k + 1
None
1/2
BRVC
k
Branch if Overflow Flag is Cleared
if (V = 0) then PC
←
PC + k + 1
None
1/2
BRIE
k
Branch if Interrupt Enabled
if (I = 1) then PC
←
PC + k + 1
None
1/2
BRID
k
Branch if Interrupt Disabled
if (I = 0) then PC
←
PC + k + 1
None
1/2
MOV
Rd, Rr
Copy Register
Rd
←
Rr
None
1
MOVW
Rd, Rr
Copy Register Pair
Rd+1:Rd
←
Rr+1:Rr
None
1
LDI
Rd, K
Load Immediate
Rd
←
K
None
1
LDS
Rd, k
Load Direct from data space
Rd
←
(k)
None
2(1)(2)
LD
Rd, X
Load Indirect
Rd
←
(X)
None
1(1)(2)
LD
Rd, X+
Load Indirect and Post-Increment
Rd
X
←
←
(X)
X+1
None
1(1)(2)
LD
Rd, -X
Load Indirect and Pre-Decrement
X ← X - 1,
Rd ← (X)
←
←
X-1
(X)
None
2(1)(2)
LD
Rd, Y
Load Indirect
Rd ← (Y)
←
(Y)
None
1(1)(2)
LD
Rd, Y+
Load Indirect and Post-Increment
Rd
Y
←
←
(Y)
Y+1
None
1(1)(2)
Data Transfer Instructions
58
8387A–AVR–07/11
XMEGA A4U
Mnemonics
Operands
Description
Flags
#Clocks
LD
Rd, -Y
Load Indirect and Pre-Decrement
Y
Rd
←
←
Y-1
(Y)
None
2(1)(2)
LDD
Rd, Y+q
Load Indirect with Displacement
Rd
←
(Y + q)
None
2(1)(2)
LD
Rd, Z
Load Indirect
Rd
←
(Z)
None
1(1)(2)
LD
Rd, Z+
Load Indirect and Post-Increment
Rd
Z
←
←
(Z),
Z+1
None
1(1)(2)
LD
Rd, -Z
Load Indirect and Pre-Decrement
Z
Rd
←
←
Z - 1,
(Z)
None
2(1)(2)
LDD
Rd, Z+q
Load Indirect with Displacement
Rd
←
(Z + q)
None
2(1)(2)
STS
k, Rr
Store Direct to Data Space
(k)
←
Rd
None
2(1)
ST
X, Rr
Store Indirect
(X)
←
Rr
None
1(1)
ST
X+, Rr
Store Indirect and Post-Increment
(X)
X
←
←
Rr,
X+1
None
1(1)
ST
-X, Rr
Store Indirect and Pre-Decrement
X
(X)
←
←
X - 1,
Rr
None
2(1)
ST
Y, Rr
Store Indirect
(Y)
←
Rr
None
1(1)
ST
Y+, Rr
Store Indirect and Post-Increment
(Y)
Y
←
←
Rr,
Y+1
None
1(1)
ST
-Y, Rr
Store Indirect and Pre-Decrement
Y
(Y)
←
←
Y - 1,
Rr
None
2(1)
STD
Y+q, Rr
Store Indirect with Displacement
(Y + q)
←
Rr
None
2(1)
ST
Z, Rr
Store Indirect
(Z)
←
Rr
None
1(1)
ST
Z+, Rr
Store Indirect and Post-Increment
(Z)
Z
←
←
Rr
Z+1
None
1(1)
ST
-Z, Rr
Store Indirect and Pre-Decrement
Z
←
Z-1
None
2(1)
STD
Z+q,Rr
Store Indirect with Displacement
(Z + q)
←
Rr
None
2(1)
Load Program Memory
R0
←
(Z)
None
3
LPM
Operation
LPM
Rd, Z
Load Program Memory
Rd
←
(Z)
None
3
LPM
Rd, Z+
Load Program Memory and Post-Increment
Rd
Z
←
←
(Z),
Z+1
None
3
Extended Load Program Memory
R0
←
(RAMPZ:Z)
None
3
ELPM
ELPM
Rd, Z
Extended Load Program Memory
Rd
←
(RAMPZ:Z)
None
3
ELPM
Rd, Z+
Extended Load Program Memory and PostIncrement
Rd
Z
←
←
(RAMPZ:Z),
Z+1
None
3
Store Program Memory
(RAMPZ:Z)
←
R1:R0
None
-
(RAMPZ:Z)
Z
←
←
R1:R0,
Z+2
None
-
Rd
←
I/O(A)
None
1
I/O(A)
←
Rr
None
1
STACK
←
Rr
None
1(1)
SPM
SPM
Z+
Store Program Memory and Post-Increment
by 2
IN
Rd, A
In From I/O Location
OUT
A, Rr
Out To I/O Location
PUSH
Rr
Push Register on Stack
POP
Rd
Pop Register from Stack
Rd
←
STACK
None
2(1)
XCH
Z, Rd
Exchange RAM location
Temp
Rd
(Z)
←
←
←
Rd,
(Z),
Temp
None
2
LAS
Z, Rd
Load and Set RAM location
Temp
Rd
(Z)
←
←
←
Rd,
(Z),
Temp v (Z)
None
2
LAC
Z, Rd
Load and Clear RAM location
(Z)
Rd
←
←
($FF – Rd) • (Z)
(Z)
None
2
59
8387A–AVR–07/11
XMEGA A4U
Mnemonics
Operands
Description
LAT
Z, Rd
Load and Toggle RAM location
Operation
Flags
#Clocks
(Z)
Rd
←
←
Rd ⊕ (Z)
(Z)
None
2
Rd(n+1)
Rd(0)
C
←
←
←
Rd(n),
0,
Rd(7)
Z,C,N,V,H
1
Rd(n)
Rd(7)
C
←
←
←
Rd(n+1),
0,
Rd(0)
Z,C,N,V
1
Rd(0)
Rd(n+1)
C
←
←
←
C,
Rd(n),
Rd(7)
Z,C,N,V,H
1
Rd(7)
Rd(n)
C
←
←
←
C,
Rd(n+1),
Rd(0)
Z,C,N,V
1
Bit and Bit-test Instructions
LSL
Rd
Logical Shift Left
LSR
Rd
Logical Shift Right
ROL
Rd
Rotate Left Through Carry
ROR
Rd
Rotate Right Through Carry
ASR
Rd
Arithmetic Shift Right
SWAP
Rd
Swap Nibbles
BSET
s
Rd(n)
←
Rd(n+1), n=0..6
Z,C,N,V
1
Rd(3..0)
↔
Rd(7..4)
None
1
Flag Set
SREG(s)
←
1
SREG(s)
1
BCLR
s
Flag Clear
SREG(s)
←
0
SREG(s)
1
SBI
A, b
Set Bit in I/O Register
I/O(A, b)
←
1
None
1
CBI
A, b
Clear Bit in I/O Register
I/O(A, b)
←
0
None
1
BST
Rr, b
Bit Store from Register to T
BLD
Rd, b
Bit load from T to Register
T
←
Rr(b)
T
1
Rd(b)
←
T
None
1
SEC
Set Carry
C
←
1
C
1
CLC
Clear Carry
C
←
0
C
1
SEN
Set Negative Flag
N
←
1
N
1
CLN
Clear Negative Flag
N
←
0
N
1
SEZ
Set Zero Flag
Z
←
1
Z
1
CLZ
Clear Zero Flag
Z
←
0
Z
1
SEI
Global Interrupt Enable
I
←
1
I
1
CLI
Global Interrupt Disable
I
←
0
I
1
SES
Set Signed Test Flag
S
←
1
S
1
CLS
Clear Signed Test Flag
S
←
0
S
1
SEV
Set Two’s Complement Overflow
V
←
1
V
1
CLV
Clear Two’s Complement Overflow
V
←
0
V
1
SET
Set T in SREG
T
←
1
T
1
CLT
Clear T in SREG
T
←
0
T
1
SEH
Set Half Carry Flag in SREG
H
←
1
H
1
CLH
Clear Half Carry Flag in SREG
H
←
0
H
1
None
1
MCU Control Instructions
BREAK
Break
NOP
No Operation
None
1
SLEEP
Sleep
(see specific descr. for Sleep)
None
1
WDR
Watchdog Reset
(see specific descr. for WDR)
None
1
Notes:
(See specific descr. for BREAK)
1. Cycle times for Data memory accesses assume internal memory accesses, and are not valid for accesses via the external
RAM interface.
2. One extra cycle must be added when accessing Internal SRAM.
60
8387A–AVR–07/11
XMEGA A4U
34. Packaging information
34.1
44A
PIN 1 IDENTIFIER
PIN 1
e
B
E1
E
D1
D
C
0°~7°
A1
A2
A
L
COMMON DIMENSIONS
(Unit of Measure = mm)
Notes:
1. This package conforms to JEDEC reference MS-026, Variation ACB.
2. Dimensions D1 and E1 do not include mold protrusion. Allowable
protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum
plastic body size dimensions including mold mismatch.
3. Lead coplanarity is 0.10 mm maximum.
SYMBOL
MIN
NOM
MAX
A
–
–
1.20
A1
0.05
–
0.15
A2
0.95
1.00
1.05
D
11.75
12.00
12.25
D1
9.90
10.00
10.10
E
11.75
12.00
12.25
E1
9.90
10.00
10.10
B
0.30
–
0.45
C
0.09
–
0.20
L
0.45
–
0.75
e
NOTE
Note 2
Note 2
0.80 TYP
2010-10-20
R
2325 Orchard Parkway
San Jose, CA 95131
TITLE
44A, 44-lead, 10 x 10 mm Body Size, 1.0 mm Body Thickness,
0.8 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP)
DRAWING NO.
REV.
44A
C
61
8387A–AVR–07/11
XMEGA A4U
34.2
44M1
D
Marked Pin# 1 ID
E
SEATING PLANE
A1
TOP VIEW
A3
A
K
L
Pin #1 Corner
D2
1
2
3
Option A
SIDE VIEW
Pin #1
Triangle
E2
Option B
K
Option C
b
e
Pin #1
Chamfer
(C 0.30)
Pin #1
Notch
(0.20 R)
BOTTOM VIEW
COMMON DIMENSIONS
(Unit of Measure = mm)
SYMBOL
MIN
NOM
MAX
A
0.80
0.90
1.00
A1
–
0.02
0.05
A3
0.20 REF
b
0.18
0.23
0.30
D
6.90
7.00
7.10
D2
5.00
5.20
5.40
E
6.90
7.00
7.10
E2
5.00
5.20
5.40
e
Note: JEDEC Standard MO-220, Fig. 1 (SAW Singulation) VKKD-3.
NOTE
0.50 BSC
L
0.59
0.64
0.69
K
0.20
0.26
0.41
9/26/08
Package Drawing Contact:
[email protected]
TITLE
44M1, 44-pad, 7 x 7 x 1.0 mm Body, Lead
Pitch 0.50 mm, 5.20 mm Exposed Pad, Thermally
Enhanced Plastic Very Thin Quad Flat No
Lead Package (VQFN)
GPC
ZWS
DRAWING NO.
REV.
44M1
H
62
8387A–AVR–07/11
XMEGA A4U
34.3
49C2
E
A1 BALL ID
0.10
D
A1
TOP VIEW
A
A2
SIDE VIEW
E1
G
e
F
E
D
D1
COMMON DIMENSIONS
(Unit of Measure = mm)
C
B
1
A1 BALL CORNER
MIN
NOM
MAX
A
–
–
1.00
A1
0.20
–
–
A2
0.65
–
–
D
4.90
5.00
5.10
SYMBOL
A
2
3
4
5
b
6
7
e
BOTTOM VIEW
49 - Ø0.35 ± 0.05
D1
E
3.90 BSC
4.90
5.00
E1
b
NOTE
5.10
3.90 BSC
0.30
0.35
e
0.40
0.65 BSC
3/14/08
Package Drawing Contact:
[email protected]
TITLE
49C2, 49-ball (7 x 7 Array), 0.65 mm Pitch,
5.0 x 5.0 x 1.0 mm, Very Thin, Fine-Pitch
Ball Grid Array Package (VFBGA)
GPC
CBD
DRAWING NO.
REV.
49C2
A
63
8387A–AVR–07/11
XMEGA A4U
35. Electrical Characteristics
All typical values are measured at T = 25°C unless other temperature condition is given. All minimum and maximum values are valid across operating temperature and voltage unless other
conditions are given.
35.1
Absolute Maximum Ratings*
Operating Temperature.................................... -55°C to +85°C
*NOTICE:
Storage Temperature ..................................... -65°C to +150°C
Voltage on any Pin with respect to Ground..-0.5V to VCC+0.5V
Maximum Operating Voltage ............................................ 4.0V
DC Current per I/O Pin ................................................ 20.0mA
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect
device reliability.
DC Current VCC and GND Pins................................. 200.0mA
35.2
DC Characteristics
Table 35-1.
Symbol
Current Consumption for Active and sleep modes
Parameter
Condition
32kHz, Ext. Clk
Active Power
consumption(1)
1MHz, Ext. Clk
2MHz, Ext. Clk
32MHz, Ext. Clk
ICC
32kHz, Ext. Clk
Idle Power
consumption(1)
1MHz, Ext. Clk
2MHz, Ext. Clk
32MHz, Ext. Clk
Min
ICC
Power-down power
consumption
50
VCC = 3.0V
130
VCC = 1.8V
260
VCC = 3.0V
540
VCC = 1.8V
460
600
0.96
1.4
9.8
12
VCC = 3.0V
Units
µA
mA
VCC = 1.8V
2.4
VCC = 3.0V
3.9
VCC = 1.8V
62
VCC = 3.0V
118
VCC = 1.8V
125
225
237
350
3.8
5.5
mA
0.1
1
µA
1.2
4.5
1.2
3
2.4
7
VCC = 3.0V
VCC = 3.0V
WDT and Sampled BOD enabled,
T = 25°C
WDT and Sampled BOD enabled,
T=85°C
Max
VCC = 1.8V
T = 25°C
T = 85°C
Typ
µA
VCC = 3.0V
64
8387A–AVR–07/11
XMEGA A4U
Table 35-1.
Symbol
Current Consumption for Active and sleep modes (Continued)
Parameter
Condition
Min
RTC on ULP clock, WDT and
sampled BOD enabled, T = 25°C
Power-save power
consumption(2)
Max
1.2
RTC on 1.024kHz low power
32.768kHz TOSC, T = 25°C
VCC = 1.8V
0.5
2
VCC = 3.0V
0.7
2
RTC from low power 32.768kHz
TOSC, T = 25°C
VCC = 1.8V
0.9
3
VCC = 3.0V
1.15
3.5
VCC = 3.0V
320
Current through RESET pin
substracted
Units
1.2
VCC = 3.0V
ICC
Reset power consumption
Typ
µA
Module and peripheral power consumption(3)
ULP oscillator
1
32.768kHz int. oscillator
27
85
2MHz int. oscillator
DFLL enabled with 32.768kHz int. osc. as reference
115
270
32MHz int. oscillator
PLL
DFLL enabled with 32.768kHz int. osc. as reference
460
Multiplication factor = 10x
220
Real Time Counter
µA
0.015
Watchdog Timer
1
Continuous mode
138
Sampled mode, include ULP oscillator
1.2
BOD
ICC
Internal 1.0V reference
100
Temperature sensor
95
3.05
ADC
DAC
250 kSPS
VREF = Ext ref
250kSPS’
VREF = Ext ref
No load
CURRLIMIT = LOW
2.61
CURRLIMIT = MEDIUM
2.16
CURRLIMIT = HIGH
1.75
Normal mode
1.63
Low Power mode
1.06
High Speed Mode
330
Low Power Mode
130
615KBps between I/O registers and SRAM
108
mA
AC
DMA
Timer/Counter
USART
16
Rx and Tx enabled, 9600 BAUD
Flash memory and EEPROM programming
Notes:
µA
2.5
3.6
mA
1. All Power Reduction Registers set.
2. Maximum limits are based on characterization and not tested in production.
65
8387A–AVR–07/11
XMEGA A4U
3. All parameters measured as the difference in current consumption between module enabled and disabled. All data at
VCC = 3.0V, ClkSYS = 1MHz External clock without prescaling, T = 25°C unless other conditiond are given .
35.3
Operating Voltage and Frequency
Table 35-2.
Symbol
ClkCPU
Operating voltage and frequency
Parameter
CPU clock frequency
Condition
Min
Typ
Max
VCC = 1.6V
0
12
VCC = 1.8V
0
12
VCC = 2.7V
0
32
VCC = 3.6V
0
32
Units
MHz
The maximum System clock frequency of the Atmel® AVR® XMEGA A4U devices is depending
on VCC. As shown in Figure 35-1 on page 66 the Frequency vs. VCC curve is linear between
1.8V < VCC < 2.7V.
Figure 35-1. Maximum Frequency vs. Vcc
MHz
32
Safe Operating Area
12
1.6 1.8
2.7
3.6
V
66
8387A–AVR–07/11
XMEGA A4U
35.4
Wakeup time from sleep
Table 35-3.
Symbol
Device wakeup time from sleep modes with various system clock sources
Parameter
Condition
External 2MHz clock
32.768kHz internal oscillator
Min
Typ
Max
Units
2
120
Wake-up time from Idle
2MHz internal oscillator
2
32MHz internal oscillator
0.17
External 2MHz clock
32.768kHz internal oscillator
2
120
Wake-up time from Standby
2MHz internal oscillator
2
32MHz internal oscillator
0.17
External 2MHz clock
twakeup
Wake-up time from Extend
Standby
32.768kHz internal oscillator
2
120
µs
2MHz internal oscillator
2
32MHz internal oscillator
0.17
External 2MHz clock
4.5
32.768kHz internal oscillator
320
2MHz internal oscillator
8.8
32MHz internal oscillator
5
Wake-up time from Power-save
External 2MHz clock
4.5
32.768kHz internal oscillator
320
2MHz internal oscillator
8.8
32MHz internal oscillator
5
Wake-up time from Power-down
67
8387A–AVR–07/11
XMEGA A4U
35.5
I/O Pin Characteristics
The I/O pins complies with the JEDEC LVTTL and LVCSMOS specification and the high- and
low level input and output voltage limits reflect or exceed this specification.
Table 35-4.
Symbol
VIH
VIL
I/O Pin Characteristics
Parameter
High Level Input Voltage
Low Level Input Voltage
Condition
VOL
VCC+0.3
VCC = 2.3 - 2.7V
1.7
VCC+0.3
VCC = 1.6 - 2.7V
0.7*VCC
VCC+0.3
VCC = 3.0 - 3.6V
-0.3
0.8
VCC = 2.3 - 2.7V
-0.3
0.7
VCC = 1.6 - 2.7V
-0.3
0.2*VCC
High Level Output Voltage
VCC = 2.3 - 2.7V
VOH
2.4
3.19
IOH = -1mA
2.0
2.43
IOH = -2mA
1.7
2.37
0.4
IOL = 1mA
0.03
0.4
IOL = 2mA
0.05
0.7
VCC = 3.3V
IOL = 15mA
0.4
0.76
VCC = 3.0V
IOL = 10mA
0.265
0.64
VCC = 1.8V
IOL = 5mA
0.18
0.46
VCC = 3.3V
IOH = -8mA
2.6
2.86
VCC = 3.0V
IOH = -6mA
2.1
2.66
VCC = 1.8V
IOH = -2mA
1.4
1.64
IIN
Input Leakage Current I/O pin
<0.001
0.1
IIL
Input Leakage Current I/O pin
<0.001
0.1
RP
I/O pin Pull/Buss keeper Resistor
27
Reset pin Pull-up Resistor
25
Input hysteresis
0.2
RRST
Units
V
0.05
VCC = 2.3 - 2.7V
Output High Voltage GPIO
IOH = -2mA
IOL = 2mA
Low Level Output Voltage
Output Low Voltage GPIO
Max
2
VCC = 3.0 - 3.6V
VOL
Typ
VCC = 3.0 - 3.6V
VCC = 3.0 - 3.6V
VOH
Min
µA
kΩ
V
4
tr
Pad rise time
No load
nS
slew rate limitation
7
68
8387A–AVR–07/11
XMEGA A4U
35.6
ADC Characteristics
Table 35-5.
ADC Characteristics
Symbol
Parameter
RES
Resolution
ClkADC
fADC
Condition(2)
Min
Typ
Max
Units
8
12
12
Bits
5
8
ClkADC
cycles
µS
Conversion time (latency)
(RES+2)/2+(GAIN !=0), RES = 8 or 2
Sampling Time
1/2 ClkADC cycle
0.25
5
Max is 1/4 of Peripheral clock frequency
100
2000
Measuring internal signals
100
125
100
2000
CURRLIMIT = LOW
100
1500
CURRLIMIT = MEDIUM
100
1000
CURRLIMIT = HIGH
100
500
VCC- 0.3
VCC+ 0.3
1
AVCC- 0.6
ADC Clock frequency
kHz
Sample rate
AVCC
Analog supply voltage
VREF
Reference voltage
kSPS
V
Rin
Input resistance
Switched
4.0
kΩ
Cin
Input capacitance
Switched
4.4
pF
RAREF
Reference input resistance
(leackage only)
>10
MΩ
CAREF
Reference input capacitance
Static load
7
pF
Start-up time
ADC clock cycles
12
24
After changing reference or input mode
7
7
After ADC flush
1
1
ADC settling time
Vin
Vin
Input range
Conversion range
Differential mode, Vinp - Vinn
Conversion range
Single ended unsigned mode, Vinp
500kSPS
INL(1)
AVCC+ 0.1
-VREF
VREF
-ΔV
VREF-ΔV
±1.2
2
±1.5
3
±1.0
2
±1.5
3
±0.8
1.2
±0.5
1.5
±0.8
1.2
±0.5
1.5
V
Integral non-linearity
2000kSPS
DNL(1)
VCC-1.0V < VREF< VCC-0.6V
-0.1
ClkADC
cycles
VCC-1.0V < VREF< VCC-0.6V
500kSPS,
guaranteed
monotonic
VCC-1.0V < VREF< VCC-0.6V
2000kSPS,
guaranteed
monotonic
VCC-1.0V < VREF< VCC-0.6V
LSB
Differential non-linearity
Offset Error
-1
mV
Temperature drift
<0.01
mV/K
Operating voltage drift
<0.6
mV/V
69
8387A–AVR–07/11
XMEGA A4U
Table 35-5.
ADC Characteristics (Continued)
Symbol
Condition(2)
Parameter
Differential
mode
Min
Typ
External reference
1
AVCC/1.6
10
AVCC/2.0
8
Bandgap
±5
Max
Units
mV
Gain Error
Notes:
Temperature drift
<0.02
mV/K
Operating voltage drift
<0.5
mV/V
1. Maximum numbers are based on characterisation and not tested in production, and valid for 5% to 95% input voltage range.
2. Unless otherwise noted all linearity, offset and gain error numbers are valid under the condition that external VREF is used.
Table 35-6.
Symbol
ADC Gain Stage Characteristics
Parameter
Condition
Min
Typ
Max
Units
Rin
Input resistance
Switched in normal mode
4.0
kΩ
Cin
Input capacitance
Switched in normal mode
4.4
pF
Signal range
Gain stage output
Propagation delay
ADC conversion rate
Clock rate
Same as ADC
INL
(1)
DNL(1)
Integral Non-Linearity
500kSPS
Differential Non-Linearity
Gain Error
Offset Error, input
refered
Note:
VCC- 0.6
0
ClkADC
cycles
1
100
V
1000
All gain settings
±2.0
4
All gain setting, guaranteed
monotonic
±0.9
1.5
kHz
LSB
1x gain, normal mode
-0.8
8x gain, normal mode
-2.5
64x gain, normal mode
-3.5
1x gain, normal mode
-2
8x gain normal mode
-5
64x gain normal mode
-4
%
mV
1. Maximum numbers are based on characterisation and not tested in production, and valid for 5% to 95% input voltage range.
70
8387A–AVR–07/11
XMEGA A4U
35.7
DAC Characteristics
Table 35-7.
Symbol
RES
DAC Characteristics
Parameter
Condition
Min
Typ
Input Resolution
AVREF
External reference voltage
Rchannel
DC output impedance
1.0
Linear output voltage range
RAREF
Reference input resistance
CAREF
Reference input capacitance
Minimum Resistance load
Units
12
Bits
VCC-0.6
V
50
Ω
AVCC-0.15
0.15
Static load
Max
>10
MΩ
7
pF
1
kΩ
100
pF
1
nF
Maximum capacitance laod
1000Ω serial resistance
Operating within specification
AVCC/1000
Output sink/source
Safe operation
Enable, reset to code
0
INL(1)
Integral non-linearity
±2.0
3
VCC = 3.6V
±1.5
2.5
VCC = 1.6V
±2.0
4
VCC = 3.6V
±1.5
4
VCC = 1.6V
±3.0
VCC = 3.6V
±3.0
VREF=Ext 1.0V,
guaranteed
monotonic
VCC = 1.6V
±1.5
3
VCC = 3.6V
±0.6
1.5
VREF=AVCC,
guaranteed
monotonic
VCC = 1.6V
±1.0
3.5
VCC = 3.6V
±0.6
1.5
VCC = 1.6V
±3.0
VCC = 3.6V
±3.0
VREF=AVCC
VREF=INT1V
DNL(1)
Differential Non-Linearity
VREF=INT1V
Gain error
Ox
VCC = 1.6V
VREF= Ext 1.0V
mA
10
After calibration
LSB
<4
Gain calibration step size
4
Gain calibration drift
VREF= Ext 1.0V
<0.2
Offset error
After calibration
<1
mV/K
LSB
Offset calibration step size
Fclk
Note:
Conversion rate
1
Fout=Fclk/4,
Cload=100pF,
Max step size
0
1000
0
1000
kSPS
1. Maximum numbers are based on characterisation and not tested in production, and valid for 5% to 95% output voltage range.
71
8387A–AVR–07/11
XMEGA A4U
35.8
Analog Comparator Characteristics
Table 35-8.
Symbol
Voff
Ilk
Analog Comparator Characteristics
Parameter
Condition
Min
Max
<±10
mV
Input Leakage Current
<1000
pA
-0.1
AC startup time
Vhys1
Hysteresis, None
Vhys2
Hysteresis, Small
Vhys3
Hysteresis, Large
AVCC+ 0.1
100
µs
mode = High Speed (HS)
14
mode = Low Power (LP)
30
mode = HS
30
mode = LP
60
mode = HS
90
mode = HS
mV
100
95
ns
Propagation delay
VCC = 3.0V, T= 85°C
64-Level Voltage Scaler
V
0
VCC = 3.0V, T= 85°C
tdelay
Units
Input Offset Voltage
Input voltage range
mode = LP
200
mode = LP
200
Integral non-linearity (INL)
0.5
Current source accuracy after calibration
500
1
5
Current source calibration range
35.9
Typ
4
LSB
%
6
µA
Bandgap and Internal 1.0V Reference Characteristics
Table 35-9.
Symbol
Bandgap and Internal 1.0V Reference Characteristics
Parameter
Condition
Min
As reference for ADC or DAC
Typ
Max
1 ClkPER + 2.5µs
Startup time
As input voltage to ADC and AC
Units
µs
1.5
Bandgap voltage
1.1
V
INT1V
Internal 1.00V reference
Variation over voltage and temperature
T= 85°C, After calibration
0.99
1
±0.5
1.01
%
72
8387A–AVR–07/11
XMEGA A4U
35.10 Brownout Detection Characteristics
Table 35-10. Brownout Detection Characteristics(1)
Symbol
Parameter
Condition
BOD level 0 falling Vcc
Min
Typ
Max
1.62
1.62
1.72
BOD level 1 falling Vcc
1.81
BOD level 2 falling Vcc
2.01
BOD level 3 falling Vcc
2.21
BOD level 4 falling Vcc
2.41
BOD level 5 falling Vcc
2.61
BOD level 6 falling Vcc
2.81
BOD level 7 falling Vcc
3.00
Units
V
VHYST
Note:
Continous mode
0,4
Sampled mode
1000
Detection time
tBOD
µs
Hysteresis
1.6
%
1. BOD is calibrated at 85°C within BOD level 0 values, and BOD level 0 is the default level.
35.11 External Reset Characteristics
Table 35-11. External Reset Characteristics
Symbol
Parameter
tEXT
Minimum reset pulse width
VRST
Reset threshold voltage
Condition
Min
Typ
Max
Units
90
1000
ns
VCC = 2.7 - 3.6V
0.50*VCC
VCC = 1.6 - 2.7V
0.40*VCC
V
35.12 Power-on Reset Characteristics
Table 35-12. Power-on Reset Characteristics
Symbol
Parameter
VPOT-
POR threshold voltage falling VCC
VPOT+
POR threshold voltage rising VCC
Condition
Min
Typ
VCC falls faster than 1V/ms
0.4
1.0
VCC falls at 1V/ms or slower
0.8
1.2
1.3
Max
Units
V
1.59
73
8387A–AVR–07/11
XMEGA A4U
35.13 Flash and EEPROM Memory Characteristics
Table 35-13. Endurance and Data Retention
Symbol
Parameter
Condition
Min
25°C
10K
85°C
10K
25°C
100
55°C
25
25°C
80K
85°C
30K
25°C
100
55°C
25
Typ
Max
Write/Erase cycles
Units
Cycle
Flash
Data retention
Year
Write/Erase cycles
Cycle
EEPROM
Data retention
Year
Table 35-14. Programming time
Symbol
Parameter
Condition
Chip Erase
(2)
Flash
EEPROM
Notes:
Flash, EEPROM
Min
and SRAM Erase
Typ(1)
Max
Units
50
Page Erase
6
Page Write
6
Page WriteAutomatic Page Erase and Write
12
Page Erase
6
Page Write
6
Page WriteAutomatic Page Erase and Write
12
ms
1. Programming is timed from the 2MHz internal oscillator.
2. EEPROM is not erased if the EESAVE fuse is programmed.
35.14 Clock and Oscillator Characteristics
35.14.1
Calibrated 32.768kHz Internal Oscillator characteristics
Table 35-15. Calibrated 32.768kHz Internal Oscillator characteristics
Symbol
Parameter
Condition
Min
Frequency
Factory calibration accuracy
User calibration accuracy
Typ
Max
32.768
T = 85°C, VCC = 3.0V
Units
kHz
-0.5
0.5
-0.5
0.5
%
74
8387A–AVR–07/11
XMEGA A4U
35.14.2
Calibrated 2MHz RC Internal Oscillator characteristics
Table 35-16. Calibrated 2MHz Internal Oscillator characteristics
Symbol
Parameter
Condition
Min
Typ
Max
Units
Frequency range
DFLL can tune to this frequency over
voltage and temperature
1.8
2.0
2.2
MHz
Factory calibration accuracy
T = 85°C, VCC= 3.0V
-1.5
1.5
-0.2
0.2
%
User calibration accuracy
DFLL calibration stepsize
35.14.3
0.21
Calibrated and tunable 32MHz Internal Oscillator characteristics
Table 35-17. Calibrated 32MHz Internal Oscillator characteristics
Symbol
Parameter
Condition
Min
Typ
Max
Units
Frequency range
DFLL can tune to this frequency over
voltage and temperature
30
32
55
MHz
Factory calibration accuracy
T = 85°C, VCC= 3.0V
-1.5
1.5
-0.2
0.2
%
Max
Units
User calibration accuracy
DFLL calibration step size
35.14.4
0.22
32kHz Internal ULP Oscillator characteristics
Table 35-18. 32kHz Internal ULP Oscillator characteristics
Symbol
Parameter
Condition
Min
Output frequency
35.14.5
Typ
38
kHz
Internal Phase Locked Loop (PLL) characteristics
Table 35-19. Calibrated 32MHz Internal Oscillator characteristics
Symbol
fIN
fOUT
Parameter
Input Frequnecy
Ouput frequnecy (1)
Condition
Min
Typ
Output frequnecy must be within fOUT
0.4
64
20
32
20
128
Start-up time
25
re-lock time
25
Max
Units
MHz
µs
1.
The maximum ouput frequency vs. supply voltage is linear between 1.8V and 2.7V, and can never be higher than 4 times the
maximum CPU frequency.
75
8387A–AVR–07/11
XMEGA A4U
35.14.6
External 32.768kHz Crystal Oscillator and TOSC characteristics
Table 35-20. External 32.768kHz Crystal Oscillator and TOSC characteristics
Symbol
Parameter
ESR/R1
Recommended crystal equivalent
series resistance (ESR)
CIN_TOSC
Condition
Typ
Max
Crystal load capacitance 6.5pF
60
Crystal load capacitance 9.0pF
35
Units
kΩ
Normal mode
4.7
Low power mode
5.2
Input capacitance between TOSC pins
pF
capacitance load matched to
crystal specification
Recommended Safety factor
Note:
Min
3
1. See Figure 35-2 on page 76 for definition
Figure 35-2. TOSC input capacitance
CL1
TOSC1
CL2
Device internal
External
TOSC2
32.768 KHz crystal
The input capacitance between the TOSC pins is CL1 + CL2 in series as seen from the crystal
when oscillating without external capacitors.
35.14.7
External Clock Characteristics
Figure 35-3. External Clock Drive Waveform
tCH
tCH
tCR
tCF
VIH1
VIL1
tCL
tCK
76
8387A–AVR–07/11
XMEGA A4U
Table 35-21. External Clock used as System Clock without prescaling
Symbol
Parameter
Clock Frequency(1)
1/tCK
tCK
Clock Period
tCH
Clock High Time
tCL
Clock Low Time
tCR
Rise Time (for maximum frequency)
tCF
Fall Time (for maximum frequency)
ΔtCK
Note:
Condition
Min
Typ
Max
VCC = 1.6 - 1.8V
0
12
VCC = 2.7 - 3.6V
0
32
VCC = 1.6 - 1.8V
83.3
VCC = 2.7 - 3.6V
31.5
VCC = 1.6 - 1.8V
30.0
VCC = 2.7 - 3.6V
12.5
VCC = 1.6 - 1.8V
30.0
VCC = 2.7 - 3.6V
12.5
Units
MHz
ns
VCC = 1.6 - 1.8V
10
VCC = 2.7 - 3.6V
3
VCC = 1.6 - 1.8V
10
VCC = 2.7 - 3.6V
3
Change in period from one clock cycle to the next
10
%
1. The maximum frequency vs. supply voltage is linear between 1.8V and 2.7V, and the same applies for all other parameters
with supply voltage conditions.
Table 35-22. External Clock with prescaler(1) for System Clock
Symbol
1/tCK
Parameter
Clock Frequency(2)
tCK
Clock Period
tCH
Clock High Time
Condition
Min
Typ
Max
VCC = 1.6 - 1.8V
0
90
VCC = 2.7 - 3.6V
0
142
VCC = 1.6 - 1.8V
11
VCC = 2.7 - 3.6V
7
VCC = 1.6 - 1.8V
4.5
VCC = 2.7 - 3.6V
2.4
VCC = 1.6 - 1.8V
4.5
VCC = 2.7 - 3.6V
2.4
MHz
ns
tCL
Clock Low Time
tCR
Rise Time (for maximum frequency)
1.5
tCF
Fall Time (for maximum frequency)
1.5
Change in period from one clock cycle to the next
10
ΔtCK
Notes:
Units
%
1. System Clock Prescalers must be set so that maximum CPU clock frequency for device is not exceeded.
2. The maximum frequency vs. supply voltage is linear between 1.8V and 2.7V, and the same applies for all other parameters
with supply voltage conditions
77
8387A–AVR–07/11
XMEGA A4U
35.15 SPI Characteristics
Figure 35-4. SPI Interface Requirements in Master mode
SS
tMOS
tSCKR
tSCKF
SCK
(CPOL = 0)
tSCKW
SCK
(CPOL = 1)
tSCKW
tMIS
MISO
(Data Input)
tMIH
tSCK
MSB
LSB
tMOH
MOSI
(Data Output)
tMOH
MSB
LSB
Figure 35-5. SPI Timing Requirements in Slave mode
SS
tSSS
tSCKR
tSCKF
tSSH
SCK
(CPOL = 0)
tSSCKW
SCK
(CPOL = 1)
tSSCKW
tSIS
MOSI
(Data Input)
tSIH
MSB
tSOSSS
MISO
(Data Output)
tSSCK
LSB
tSOS
MSB
tSOSSH
LSB
78
8387A–AVR–07/11
XMEGA A4U
Table 35-23. SPI Timing Characteristics and Requirements
Symbol
Parameter
Condition
Min
Typ
Max
tSCK
SCK Period
Master
(See Table 21-4 in
XMEGA AU Manual)
tSCKW
SCK high/low width
Master
0.5*SCK
tSCKR
SCK Rise time
Master
2.7
tSCKF
SCK Fall time
Master
2.7
tMIS
MISO setup to SCK
Master
10
tMIH
MISO hold after SCK
Master
10
tMOS
MOSI setup SCK
Master
0.5*SCK
tMOH
MOSI hold after SCK
Master
1
tSSCK
Slave SCK Period
Slave
4*t ClkPER
tSSCKW
SCK high/low width
Slave
2*t ClkPER
tSSCKR
SCK Rise time
Slave
1600
tSSCKF
SCK Fall time
Slave
1600
tSIS
MOSI setup to SCK
Slave
tSIH
MOSI hold after SCK
Slave
tSSS
SS setup to SCK
Slave
21
tSSH
SS hold after SCK
Slave
20
tSOS
MISO setup SCK
Slave
8
tSOH
MISO hold after SCK
Slave
13
tSOSS
MISO setup after SS low
Slave
11
tSOSH
MISO hold after SS high
Slave
8
Units
ns
3
t ClkPER
79
8387A–AVR–07/11
XMEGA A4U
35.16 Two-Wire Interface Characteristics
Table 2-1 describes the requirements for devices connected to the Two Wire Serial Bus. The
XMEGA Two-Wire Interface meets or exceeds these requirements under the noted conditions.
Timing symbols refer to Figure 35-6.
Figure 35-6. Two-Wire Interface Bus Timing
tof
tHIGH
tLOW
tr
SCL
tSU;STA
tHD;DAT
tHD;STA
tSU;STO
tSU;DAT
SDA
tBUF
Table 35-24. Two Wire Serial Bus Characteristics
Symbol
Parameter
VIH
Input High Voltage
0.7VCC
VCC+0.5
VIL
Input Low Voltage
0.5
0.3*VCC
Vhys
Hysteresis of Schmitt Trigger Inputs
VOL
Output Low Voltage
tr
Rise Time for both SDA and SCL
tof
Output Fall Time from VIHmin to VILmax
tSP
Spikes Suppressed by Input Filter
II
Input Current for each I/O Pin
CI
Capacitance for each I/O Pin
fSCL
SCL Clock Frequency
RP
Value of Pull-up resistor
tHD;STA
Hold Time (repeated) START condition
tLOW
Low Period of SCL Clock
tHIGH
High Period of SCL Clock
tSU;STA
Set-up time for a repeated START condition
Condition
Min
0.05VCC
3mA, sink current
10pF < Cb < 400pF(2)
0.1VCC < VI < 0.9VCC
fPER(3)>max(10fSCL, 250kHz)
fSCL ≤ 100kHz
Typ
Max
Unit
s
V
(1)
0
0.4
20+0.1Cb(1)(2)
300
20+0.1Cb(1)(2)
250
0
50
-10
10
µA
10
pF
400
kHz
0
fSCL > 100kHz
V CC – 0.4V
---------------------------3mA
fSCL ≤ 100kHz
4.0
fSCL > 100kHz
0.6
fSCL ≤ 100kHz
4.7
fSCL > 100kHz
1.3
fSCL ≤ 100kHz
4.0
fSCL > 100kHz
0.6
300ms
----------------Cb
ns
Ω
µs
fSCL ≤ 100kHz
fSCL > 100kHz
80
8387A–AVR–07/11
XMEGA A4U
Table 35-24. Two Wire Serial Bus Characteristics (Continued)
Symbol
Parameter
tHD;DAT
Data hold time
tSU;DAT
Data setup time
tSU;STO
Setup time for STOP condition
tBUF
Bus free time between a STOP and START
condition
Notes:
Condition
Min
Typ
Max
fSCL ≤ 100kHz
0
3.45
fSCL > 100kHz
0
0.9
fSCL ≤ 100kHz
250
fSCL > 100kHz
100
fSCL ≤ 100kHz
4.0
fSCL > 100kHz
0.6
fSCL ≤ 100kHz
4.7
fSCL > 100kHz
1.3
Unit
s
µs
1. Required only for fSCL > 100kHz
2. Cb = Capacitance of one bus line in pF
3. fPER = Peripheral clock frequency
81
8387A–AVR–07/11
XMEGA A4U
36. Typical Characteristics
36.1
Active Supply Current
Figure 36-1. Active Supply Current vs. Frequency
fSYS = 0 - 1.0MHz External clock, T = 25°C
700
3.3V
600
3.0V
500
ICC [µA]
2.7V
400
2.2V
300
1.8V
200
100
0
0
0.2
0.4
0.6
0.8
1
Frequency [MHz]
Figure 36-2. Active supply current vs. frequency
fSYS = 1 - 32MHz External clock, T = 25°C
12
3.3V
10
3.0V
2.7V
ICC [mA]
8
6
2.2V
4
1.8V
2
0
0
4
8
12
16
20
24
28
32
Frequency [MHz]
82
8387A–AVR–07/11
XMEGA A4U
Figure 36-3. Active Supply Current vs. Vcc
fSYS = 1.0MHz External Clock
0.8
-40°C
25°C
85°C
0.7
ICC [mA]
0.6
0.5
0.4
0.3
0.2
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
Figure 36-4. Active Supply Current vs. VCC
fSYS = 2.0MHz internal oscillator
1.5
-40°C
1.4
25°C
85°C
1.3
1.2
ICC [mA]
1.1
1.0
0.9
0.8
0.7
0.6
0.5
0.4
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
83
8387A–AVR–07/11
XMEGA A4U
36.2
Idle Supply Current
Figure 36-5. Idle Supply Current vs. Frequency
fSYS = 0 - 1.0MHz, T = 25°C
ICC [µA]
140
3.3V
120
3.0V
100
2.7V
80
2.2V
60
1.8V
40
20
0
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
Frequency [MHz]
Figure 36-6. Idle Supply Current vs. Frequency
fSYS = 1 - 32MHz, T = 25°C
4.5
3.3V
4.0
3.0V
3.5
2.7V
ICC [mA]
3.0
2.5
2.0
2.2V
1.5
1.0
1.8V
0.5
0
0
4
8
12
16
20
24
28
32
Frequency [MHz]
84
8387A–AVR–07/11
XMEGA A4U
Figure 36-7. Idle Supply Current vs. Vcc
fSYS = 32.768kHz internal oscillator
33
-40°C
85°C
32
25°C
ICC [µA]
31
30
29
28
27
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
Figure 36-8. Idle Supply Current vs. Vcc
fSYS = 1.0MHz internal oscillator
160
85 °C
25 °C
-40 °C
150
140
130
ICC [µA]
120
110
100
90
80
70
60
50
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
85
8387A–AVR–07/11
XMEGA A4U
Figure 36-9. Idle Supply Current vs. Vcc
fSYS = 2.0MHz internal oscillator
410
-40°C
25°C
85°C
380
350
ICC [µA]
320
290
260
230
200
170
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
Figure 36-10. Idle Supply Current vs. Vcc
fSYS = 32MHz internal oscillator
5.6
-40°C
5.4
25°C
5.2
5.0
85°C
ICC [mA]
4.8
4.6
4.4
4.2
4.0
3.8
3.6
3.4
2.7
2.8
2.9
3
3.1
3.2
3.3
3.4
3.5
3.6
VCC [V]
86
8387A–AVR–07/11
XMEGA A4U
Figure 36-11. Idle Supply Current vs. Vcc
fSYS = 32MHz internal oscillator, prescaled to 8MHz
2.0
-40 °C
25 °C
85 °C
1.8
ICC [mA]
1.6
1.4
1.2
1.0
0.8
0.6
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
36.3
Power-down Supply Current
Figure 36-12. Power-down Supply Current vs. Temperature
All functions disabled
1.2
3.3V
3.0V
2.7V
1
2.2V
1.8V
ICC [µA]
0.8
0.6
0.4
0.2
0
-45
-35
-25
-15
-5
5
15
25
35
45
55
65
75
85
Temperature [°C]
87
8387A–AVR–07/11
XMEGA A4U
Figure 36-13. Power-down Supply Current vs. Temperature
With WDT and sampled BOD enabled.p
2.6
3.3V
3.0V
2.7V
ICC [µA]
2.3
2.2V
1.8V
2
1.7
1.4
1.1
-45
-35
-25
-15
-5
5
15
25
35
45
55
65
75
85
Temperature [°C]
36.4
Pin Pull-up
Figure 36-14. Reset and I/O Pull-up Resistor Current vs. Reset Pin Voltage
VCC = 1.8V
70
60
IPIN [µA]
50
40
30
20
-40 °C
25 °C
85 °C
10
0
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
VRESET [V]
88
8387A–AVR–07/11
XMEGA A4U
Figure 36-15. Reset and I/O Pull-up Resistor Current vs. Reset Pin Voltage
VCC = 3.0V
120
108
96
IPIN [µA]
84
72
60
48
36
24
-40 °C
25 °C
85 °C
12
0
0
0.3
0.6
0.9
1.2
1.5
1.8
2.1
2.4
2.7
3
VRESET [V]
Figure 36-16. Reset and I/O Pull-up Resistor Current vs. Reset Pin Voltage
VCC = 3.3V
130
117
104
IPIN [µA]
91
78
65
52
39
26
-40 °C
25 °C
85 °C
13
0
0
0.3
0.6
0.9
1.2
1.5
1.8
2.1
2.4
2.7
3
3.3
VRESET [V]
89
8387A–AVR–07/11
XMEGA A4U
36.5
Pin Output Voltage vs. Sink/Source Current
Figure 36-17. I/O Pin Output Voltage vs. Source Current
Vcc = 1.8V
0
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
-1
-2
1.8
85 °C
25 °C
-20 °C
IOH [mA]
-3
-4
-5
-6
-7
-8
-9
-10
VPIN [V]
Figure 36-18. I/O Pin Output Voltage vs. Source Current
Vcc = 3.0V
0
1.5
1.65
1.8
1.95
2.1
2.25
2.4
2.55
2.7
2.85
3
85 °C
25 °C
-40 °C
-2
-4
IOH [mA]
-6
-8
-10
-12
-14
-16
-18
-20
VPIN [V]
90
8387A–AVR–07/11
XMEGA A4U
Figure 36-19. I/O Pin Output Voltage vs. Source Current
Vcc = 3.3V
1.8
1.95
2.1
2.25
2.4
2.55
2.7
2.85
3
3.15
0
-2
3.3
85 °C
25 °C
-40 °C
-4
IOH [mA]
-6
-8
-10
-12
-14
-16
-18
-20
VPIN [V]
Figure 36-20. I/O Pin Output Voltage vs. Source Current
T = 25°C
3.6
3.6 V
3.3 V
3.3
3
2.7 V
VOH [V]
2.7
2.4
2.2 V
2.1
1.8
1.8 V
1.5
1.2
0.9
0.6
0.3
0
-20
-18
-16
-14
-12
-10
-8
-6
-4
-2
0
IPIN [mA]
91
8387A–AVR–07/11
XMEGA A4U
Figure 36-21. I/O Pin Output Voltage vs. Sink Current
Vcc = 1.8V
2.75
85°C
2.5
2.25
2
20°C
VOL [V]
1.75
1.5
1.25
1
-40°C
0.75
0.5
0.25
0
0
2.5
5
7.5
10
12.5
15
17.5
20
IPIN [mA]
Figure 36-22. I/O Pin Output Voltage vs. Sink Current
T= 25°C
2
1.8 V
1.8
1.6
VOL [V]
1.4
1.2
1
2.2 V
2.7 V
3.3 V
3.6 V
0.8
0.6
0.4
0.2
0
0
2
4
6
8
10
12
14
16
18
20
IPIN [mA]
92
8387A–AVR–07/11
XMEGA A4U
Figure 36-23. I/O Pin Sink Current vs. Output Voltage
Vcc = 3.0V
20
-20 °C
25 °C
18
85 °C
16
IIOL [mA]
14
12
10
8
6
4
2
0
0
0.05
0.1
0.15
0.2
0.25
0.3
0.35
0.4
0.45
0.5
VPIN [V]
Figure 36-24. I/O Pin Sink Current vs. Output Voltage
Vcc = 3.3V
22
-20 °C
25 °C
85 °C
20
18
16
IIOL [mA]
14
12
10
8
6
4
2
0
0
0.05
0.1
0.15
0.2
0.25
0.3
0.35
0.4
0.45
0.5
VPIN [V]
93
8387A–AVR–07/11
XMEGA A4U
36.6
Pin Thresholds and Hysteresis
Figure 36-25. I/O Pin Input Threshold Voltage vs. VCC
T = 25°C
VThreshold [V]
1.85
1.7
VIH
1.55
VIL
1.4
1.25
1.1
0.95
0.8
0.65
0.5
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
Figure 36-26. I/O Pin Input Hysteresis vs. VCC
T = 25°C
0.315
0.3
Hysteresis [V]
0.285
0.27
0.255
0.24
0.225
0.21
0.195
0.18
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
94
8387A–AVR–07/11
XMEGA A4U
Figure 36-27. Reset Input Threshold Voltage vs. VCC
VIH - I/O Pin Read as “1”
-40°C
25°C
85°C
1.8
1.7
1.6
1.5
VTHRESHOLD [V]
1.4
1.3
1.2
1.1
1
0.9
0.8
0.7
0.6
0.5
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
Figure 36-28. Reset Input Threshold Voltage vs. VCC
VIL - I/O Pin Read as “0”
-40°C
25°C
85°C
1.8
1.7
1.6
1.5
VTHRESHOLD [V]
1.4
1.3
1.2
1.1
1
0.9
0.8
0.7
0.6
0.5
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
95
8387A–AVR–07/11
XMEGA A4U
36.7
Bod characteristics
Figure 36-29. BOD Thresholds vs. Temperature
BOD Level = 1.6V
1.629
1.626
1.623
Rising Vcc
VBOT [V]
1.62
Falling Vcc
1.617
1.614
1.611
1.608
1.605
1.602
-45
-35
-25
-15
-5
5
15
25
35
45
55
65
75
85
45
55
65
75
85
Temperature [°C]
Figure 36-30. BOD Thresholds vs. Temperature
BOD Level = 2.6V
2.648
2.642
2.636
2.63
VBOT [V]
Rising Vcc
2.624
2.618
2.612
Falling Vcc
2.606
2.6
2.594
2.588
-45
-35
-25
-15
-5
5
15
25
35
Temperature [°C]
96
8387A–AVR–07/11
XMEGA A4U
36.8
36.8.1
Oscillators
Internal 1kHz Oscillator
Figure 36-31. 1kHz Ouput from Internal ULP Oscillator Frequency vs. Temperature
1.17
Frequency [kHz]
1.16
1.15
1.14
1.13
1.12
3.3 V
3.0 V
2.7 V
2.2 V
1.8 V
1.11
1.1
1.09
25
30
35
40
45
50
55
60
65
70
75
80
85
Temperature [°C]
36.8.2
32.768kHz Internal Oscillator
Figure 36-32. 32.768kHz Internal Oscillator Frequency vs. Temperature
1.8V
2.2V
2.7V
3.3V
3.0V
32.81
32.79
Frequency [kHz]
32.77
32.75
32.73
32.71
32.69
32.67
-45
-35
-25
-15
-5
5
15
25
35
45
55
65
75
85
Temperature [°C]
97
8387A–AVR–07/11
XMEGA A4U
36.8.3
2MHz Internal Oscillator
Figure 36-33. 2MHz Internal Oscillator CALA Calibration Step Size
VCC = 3V
0.32 %
0.29 %
Step size [%]
0.26 %
0.23 %
0.20 %
-40°C
0.17 %
25°C
85°C
0.14 %
0
10
20
30
40
50
60
70
80
90
100
110
120
130
75
3.3V
3.0V
2.7V
2.2V
1.8V
85
CALA
Frequency [MHz]
Figure 36-34. 2MHz Internal Oscillator Frequency vs. Temperature
2.15
2.14
2.13
2.12
2.11
2.1
2.09
2.08
2.07
2.06
2.05
2.04
2.03
2.02
2.01
2
1.99
1.98
-45
-35
-25
-15
-5
5
15
25
35
45
55
65
Temperature [°C]
98
8387A–AVR–07/11
XMEGA A4U
Figure 36-35. 2MHz Internal Oscillator Frequency vs. Temperature
DFLL enabled, from 32.768kHz internal oscillator
2.005
2.7V
2.2V
3.3V
3.0V
1.8V
2.004
Frequency [MHz]
2.003
2.002
2.001
2
1.999
1.998
1.997
1.996
1.995
-45
-35
-25
-15
-5
5
15
25
35
45
55
65
75
85
Temperature [°C]
36.8.4
32MHZ Internal Oscillator
Figure 36-36. 32MHz Internal Oscillator Frequency vs. Temperature
DFLL disabled
35.7
35.2
Frequency [MHz]
34.7
34.2
33.7
33.2
32.7
3.3V
3.0V
2.7V
2.2V
1.8V
32.2
31.7
-45
-35
-25
-15
-5
5
15
25
35
45
55
65
75
85
Temperature [°C]
99
8387A–AVR–07/11
XMEGA A4U
Figure 36-37. 32MHz Internal Oscillator Frequency vs. Temperature
DFLL enabled, from 32.768kHz internal oscillator
2.2V
3.0V
2.7V
1.8V
3.3V
32.06
32.04
Frequency [MHz]
32.02
32
31.98
31.96
31.94
31.92
31.9
31.88
-45
-35
-25
-15
-5
5
15
25
35
45
55
65
75
85
Temperature [°C]
Figure 36-38. 32MHz Internal Oscillator CALA Calibration Step Size
VCC = 3.0V
0.36 %
0.34 %
0.32 %
0.30 %
Step size [%]
0.28 %
0.26 %
0.24 %
0.22 %
0.20 %
0.18 %
85°C
0.16 %
25°C
0.14 %
-40°C
0.12 %
0
10
20
30
40
50
60
70
80
90
100
110
120
130
CALA
100
8387A–AVR–07/11
XMEGA A4U
36.8.5
32MHz Internal Oscillator Calibrated to 48MHZ
Figure 36-39. 48MHz Internal Oscillator Frequency vs. Temperature
DFLL disabled
53.5
Frequency [MHz]
52.5
51.5
50.5
49.5
3.3V
3.0V
2.7V
2.2V
1.8V
48.5
47.5
-45
-35
-25
-15
-5
5
15
25
35
45
55
65
75
85
Temperature [°C]
Figure 36-40. 48MHz Internal Oscillator Frequency vs. Temperature
DFLL enabled, from 32.768kHz internal oscillator
48.08
2.2V
3.3V
1.8V
3.0V
2.7V
48.05
Frequency [MHz]
48.02
47.99
47.96
47.93
47.9
47.87
47.84
-45
-35
-25
-15
-5
5
15
25
35
45
55
65
75
85
Temperature [°C]
101
8387A–AVR–07/11
XMEGA A4U
36.9
Analog comparator characteristics
Figure 36-41. AC current consumption vs. Vcc
Low-power mode
147
85°C
Current consumption [µA]
142
137
25°C
132
127
122
-40°C
117
112
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
Figure 36-42. AC current consumption vs. Vcc
High speed mode
360
85°C
Current consumption [µA]
350
340
25°C
330
320
310
-40°C
300
290
280
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
102
8387A–AVR–07/11
XMEGA A4U
Figure 36-43. Analog comparator hysteresis vs. Vcc
High-speed mode, small hysteresis
19
18
85°C
-40°C
17
25°C
VHYST [mV]
16
15
14
13
12
11
10
9
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
Figure 36-44. Analog comparator hysteresis vs. Vcc
High-speed mode, large hysteresis
40
85°C
38
25°C
-40°C
36
VHYST [mV]
34
32
30
28
26
24
22
20
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
103
8387A–AVR–07/11
XMEGA A4U
Figure 36-45. Analog comparator propagation delay vs. Vcc
High-speed mode
170
tPD [ns]
147
124
101
85°C
78
25°C
-40°C
55
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
Figure 36-46. Analog comparator propagation delay vs. temperature
High-speed mode.
170
1.6V
tPD [ns]
147
124
101
2.7V
3.6V
78
55
-45
-35
-25
-15
-5
5
15
25
35
45
55
65
75
85
Temperature [°C]
104
8387A–AVR–07/11
XMEGA A4U
Figure 36-47. Analog comparator propagation delay vs. temperature
Low-power mode
260
1.6V
250
240
tPD [ns]
230
220
210
200
2.7V
3.6V
190
180
170
-45
-35
-25
-15
-5
5
15
25
35
45
55
65
75
85
Temperature [°C]
36.10 ADC characteristics
Figure 36-48. Gain Error vs. External VREF
T = 25°C, VCC = 3.6V, ADC sampling speed = 500kSPS
3
Single-ended Signed
Gain Error [mV]
2
1
Differential Mode
0
-1
Single-ended Unsigned
-2
-3
-4
1
1.2
1.4
1.6
1.8
2
2.2
2.4
2.6
2.8
3
VREF
105
8387A–AVR–07/11
XMEGA A4U
Figure 36-49. Gain Error vs. VCC
T = 25°C, VREF= External 1.0V, ADC sampling speed = 500kSPS
2.2
1.9
Single-ended Signed
Gain Error [mV]
1.6
1.3
Differential Mode
1
0.7
0.4
Single-ended Unsigned
0.1
-0.2
-0.5
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
2.4
2.6
2.8
3
VCC [V]
Figure 36-50. Offset Error vs. External VREF
T = 25°C, VCC = 3.6V, ADC sampling speed = 500kSPS
-1
1
1.2
1.4
1.6
1.8
2
2.2
Offset Error [mV]
-1.1
-1.2
-1.3
-1.4
-1.5
Differential Mode
-1.6
-1.7
-1.8
-1.9
-2
VREF [V]
106
8387A–AVR–07/11
XMEGA A4U
Figure 36-51. Offset Error vs. VCC
T = 25°C, VREF = External 1.0V, ADC sampling rate = 500kSPS.
-0.3
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
-0.4
Offset Error [mV]
-0.5
-0.6
-0.7
Differential Mode
-0.8
-0.9
-1
-1.1
-1.2
VCC [V]
Figure 36-52. Gain Error vs. Temperature
VCC = 3.0V, VREF = External 2.0V
3
2
Gain Error [mV]
Single-ended Signed
1
Differential Mode
0
-1
Single-ended Unsigned
-2
-3
-4
-45
-35
-25
-15
-5
5
15
25
35
45
55
65
75
85
Temperature [ºC]
107
8387A–AVR–07/11
XMEGA A4U
Figure 36-53. INL error vs. External VREF
T = 25°C, VCC = 3.6V.
1.8
1.7
1.6
Differential Mode
INL [LSB]
1.5
Single-ended Unsigned
1.4
1.3
1.2
1.1
1
0.9
Single-ended Signed
0.8
0.7
1
1.2
1.4
1.6
1.8
2
2.2
2.4
2.6
2.8
3
2.6
2.8
3
VREF [V]
Figure 36-54. DNL error vs. External VREF
T = 25°C, VCC = 3.6V
0.9
0.88
0.86
DNL [LSB]
Differential Mode
0.84
Single-ended Signed
0.82
0.8
0.78
Single-ended Unsigned
0.76
0.74
0.72
1
1.2
1.4
1.6
1.8
2
2.2
2.4
VREF [V]
108
8387A–AVR–07/11
XMEGA A4U
Figure 36-55. INL error vs. Sample Rate
T = 25°C, VCC = 3.6V, VREF = 3.0V External Reference.
1.4
1.35
1.3
Differential Mode
INL [LSB]
1.25
1.2
Single-ended Unsigned
1.15
1.1
1.05
Single-ended Signed
1
0.95
0.9
500
650
800
950
1100
1250
1400
1550
1700
1850
2000
1850
2000
ADC Sample Rate [kSPS]
Figure 36-56. DNL error vs. Sample Rate
T = 25°C, VCC = 3.6V, VREF = 3.0V External Reference.
0.9
0.89
Differential Mode
0.88
DNL [LSB]
0.87
0.86
0.85
Single-ended Signed
0.84
0.83
0.82
0.81
Single-ended Unsigned
0.8
0.79
500
650
800
950
1100
1250
1400
1550
1700
ADC Sample Rate [kSPS]
109
8387A–AVR–07/11
XMEGA A4U
36.11 DAC characteristics
Figure 36-57. DNL error vs. External VREF
VCC = 3.6V
0.9
0.85
DNL
0.8
0.75
0.7
0.65
25ºC
0.6
1.6
1.8
2
2.2
2.4
2.6
2.8
3
VREF [V]
Figure 36-58. INL error vs. External VREF
VCC = 3.6V
1.9
1.8
INL [LSB]
1.7
1.6
1.5
1.4
1.3
1.2
25ºC
1.1
1
1.2
1.4
1.6
1.8
2
2.2
2.4
2.6
2.8
3
VREF [V]
110
8387A–AVR–07/11
XMEGA A4U
36.12 PDI characteristics
Figure 36-59. Maximum PDI speed vs. Vcc
32
25°C
-40°C
85°C
29.5
fMAX [MHz]
27
24.5
22
19.5
17
14.5
12
1.6
1.85
2.1
2.35
2.6
2.85
3.1
3.35
3.6
VCC [V]
36.13 Power-on reset characteristics
Figure 36-60. Power-on reset threshold vs. temperature.
1.295
uBOD threshold [V]
1.285
Rising Vcc
1.275
Falling Vcc
1.265
1.255
1.245
-45
-35
-25
-15
-5
5
15
25
35
45
55
65
75
85
Temperature [°C]
111
8387A–AVR–07/11
XMEGA A4U
Figure 36-61. Power-on reset current consumption vs. Vcc.
2000
-40°C
25°C
85°C
1800
1600
ICC [µA]
1400
1200
1000
800
600
400
200
0
1.6 1.7 1.8 1.9
2
2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9
3
3.1 3.2 3.3
VCC [V]
36.14 Bandgap and internal 1.0V characteristics
Figure 36-62. Internal 1.0V reference voltage vs. temperature.
1.004
1.8V
2.2V
2.7V
3.2V
3.6V
1.002
Bandgap Voltage [V]
1
0.998
0.996
0.994
0.992
0.99
0.988
0.986
-45
-35
-25
-15
-5
5
15
25
35
45
55
65
75
85
Temperature [°C]
112
8387A–AVR–07/11
XMEGA A4U
36.15 Reset pin characteristics
Figure 36-63. Minimum Reset Pulse vs. Vcc.
130
125
120
tRST [ns]
115
110
105
100
95
85°C
90
25°C
-40°C
85
80
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VCC [V]
113
8387A–AVR–07/11
XMEGA A4U
37. Errata
37.1
37.1.1
ATxmega16A4U, ATxmega32A4U
rev. E
• CRC fails for Range CRC when end address is the last word address of a flash section
• AWeX fault protection restore is not done correct in Pattern Generation Mode
1. CRC fails for Range CRC when end address is the last word address of a flash section
If boot read lock is enabled, the range CRC cannot end on the last address of the application
section. If application table read lock is enabled, the range CRC cannot end on the last
address before the application table.
Problem fix/Workaround
Ensure that the end address used in Range CRC does not end at the last address before a
section with read lock enabled. Instead, use the dedicated CRC commands for complete
applications sections.
2. AWeX fault protection restore is not done correctly in Pattern Generation Mode
When a fault is detected the OUTOVEN register is cleared, and when fault condition is
cleared, OUTOVEN is restored according to the corresponding enabled DTI channels. For
Common Waveform Channel Mode (CWCM), this has no effect as the OUTOVEN is correct
after restoring from fault. For Pattern Generation Mode (PGM), OUTOVEN should instead
have been restored according to the DTILSBUF register.
Problem fix/Workaround
For CWCM no workaround is required.
For PGM in latched mode, disable the DTI channels before returning from the fault condition. Then, set correct OUTOVEN value and enable the DTI channels, before the direction
(DIR) register is written to enable the correct outputs again.
For PGM in cycle-by-cycle mode there is no workaround.
37.1.2
rev. A - D
Not sampled.
114
8387A–AVR–07/11
XMEGA A4U
38. Datasheet Revision History
Please note that the referring page numbers in this section are referred to this document. The
referring revision in this section are referring to the document revision.
38.1
8387A – 07/11
1.
Initial revision.
115
8387A–AVR–07/11
XMEGA A4U
Table of Contents
Features ..................................................................................................... 1
Typical Applications ................................................................................ 1
1
Ordering Information ............................................................................... 2
2
Pinout/Block Diagram .............................................................................. 3
3
Overview ................................................................................................... 5
3.1Block Diagram ...........................................................................................................6
4
Resources ................................................................................................. 7
4.1Recommended reading .............................................................................................7
5
Capacitive touch sensing ........................................................................ 7
6
AVR CPU ................................................................................................... 8
6.1Features ....................................................................................................................8
6.2Overview ...................................................................................................................8
6.3ALU - Arithmetic Logic Unit .......................................................................................9
6.4Program Flow ............................................................................................................9
6.5Register File ..............................................................................................................9
7
Memories ................................................................................................ 10
7.1Features ..................................................................................................................10
7.2Overview .................................................................................................................10
7.3Flash Program Memory ...........................................................................................11
7.4Data Memory ...........................................................................................................11
7.5Production Signature Row .......................................................................................12
7.6User Signature Row ................................................................................................13
7.7Flash and EEPROM Page Size ...............................................................................14
8
DMAC - Direct Memory Access Controller .......................................... 15
8.1Features ..................................................................................................................15
8.2Overview .................................................................................................................15
9
Event System ......................................................................................... 16
9.1Features ..................................................................................................................16
9.2Overview .................................................................................................................16
10 System Clock and Clock options ......................................................... 18
10.1Features ................................................................................................................18
i
8387A–AVR–07/11
XMEGA A4U
10.2Overview ...............................................................................................................18
10.3Clock Options ........................................................................................................19
11 Power Management and Sleep Modes ................................................. 21
11.1Features ................................................................................................................21
11.2Overview ...............................................................................................................21
11.3Sleep Modes .........................................................................................................21
12 System Control and Reset .................................................................... 23
12.1Features ................................................................................................................23
12.2Overview ...............................................................................................................23
12.3Reset Sources .......................................................................................................23
13 WDT - Watchdog Timer ......................................................................... 25
13.1Overview ...............................................................................................................25
14 Interrupts and Programmable Multi-level Interrupt Controller .......... 26
14.1Features ................................................................................................................26
14.2Overview ...............................................................................................................26
14.3Interrupt vectors ....................................................................................................26
15 I/O Ports .................................................................................................. 28
15.1Features ................................................................................................................28
15.2Overview ...............................................................................................................28
15.3Output Driver .........................................................................................................29
15.4Input sensing .........................................................................................................31
15.5Alternate Port Functions ........................................................................................31
16 T/C - 16-bit Timer/Counter ..................................................................... 32
16.1Features ................................................................................................................32
16.2Overview ...............................................................................................................32
17 AWeX - Advanced Waveform Extension .............................................. 34
17.1Features ................................................................................................................34
17.2Overview ...............................................................................................................34
18 Hi-Res - High Resolution Extension ..................................................... 35
18.1Features ................................................................................................................35
18.2Overview ...............................................................................................................35
19 RTC - 16-bit Real-Time Counter ............................................................ 36
19.1Features ................................................................................................................36
ii
8387A–AVR–07/11
XMEGA A4U
19.2Overview ...............................................................................................................36
20 USB - Universal Serial Bus Interface ................................................... 37
20.1Features ................................................................................................................37
20.2Overview ...............................................................................................................37
21 TWI - Two Wire Interface ....................................................................... 39
21.1Features ................................................................................................................39
21.2Overview ...............................................................................................................39
22 SPI - Serial Peripheral Interface ............................................................ 40
22.1Features ................................................................................................................40
22.2Overview ...............................................................................................................40
23 USART ..................................................................................................... 41
23.1Features ................................................................................................................41
23.2Overview ...............................................................................................................41
24 IRCOM - IR Communication Module .................................................... 42
24.1Features ................................................................................................................42
24.2Overview ...............................................................................................................42
25 AES and DES Crypto Engine ................................................................ 43
25.1Features ................................................................................................................43
25.2Overview ...............................................................................................................43
26 CRC - Cyclic Redundancy Check Generator ....................................... 44
26.1Features ................................................................................................................44
26.2Overview ...............................................................................................................44
27 ADC - 12-bit Analog to Digital Converter ............................................. 45
27.1Features ................................................................................................................45
27.2Overview ...............................................................................................................45
28 DAC - 12-bit Digital to Analog Converter ............................................. 47
28.1Features ................................................................................................................47
28.2Overview ...............................................................................................................47
29 AC - Analog Comparator ....................................................................... 48
29.1Features ................................................................................................................48
29.2Overview ...............................................................................................................48
30 Programming and Debugging .............................................................. 50
iii
8387A–AVR–07/11
XMEGA A4U
30.1Features ................................................................................................................50
30.2Overview ...............................................................................................................50
31 Pinout and Pin Functions ...................................................................... 51
31.1Alternate Pin Functions Description ......................................................................51
31.2Alternate Pin Functions .........................................................................................53
32 Peripheral Module Address Map .......................................................... 56
33 Instruction Set Summary ...................................................................... 57
34 Packaging information .......................................................................... 61
34.144A ........................................................................................................................61
34.244M1 .....................................................................................................................62
34.349C2 ......................................................................................................................63
35 Electrical Characteristics ...................................................................... 64
35.1Absolute Maximum Ratings* .................................................................................64
35.2DC Characteristics ................................................................................................64
35.3Operating Voltage and Frequency ........................................................................66
35.4Wakeup time from sleep ........................................................................................67
35.5I/O Pin Characteristics ...........................................................................................68
35.6ADC Characteristics .............................................................................................69
35.7DAC Characteristics .............................................................................................71
35.8Analog Comparator Characteristics .......................................................................72
35.9Bandgap and Internal 1.0V Reference Characteristics .........................................72
35.10Brownout Detection Characteristics ....................................................................73
35.11External Reset Characteristics ............................................................................73
35.12Power-on Reset Characteristics ..........................................................................73
35.13Flash and EEPROM Memory Characteristics .....................................................74
35.14Clock and Oscillator Characteristics ....................................................................74
35.15SPI Characteristics ..............................................................................................78
35.16Two-Wire Interface Characteristics .....................................................................80
36 Typical Characteristics .......................................................................... 82
36.1Active Supply Current ............................................................................................82
36.2Idle Supply Current ................................................................................................84
36.3Power-down Supply Current .................................................................................87
36.4Pin Pull-up .............................................................................................................88
36.5Pin Output Voltage vs. Sink/Source Current .........................................................90
iv
8387A–AVR–07/11
36.6Pin Thresholds and Hysteresis ..............................................................................94
36.7Bod characteristics ................................................................................................96
36.8Oscillators ..............................................................................................................97
36.9Analog comparator characteristics ......................................................................102
36.10ADC characteristics ...........................................................................................105
36.11DAC characteristics ...........................................................................................110
36.12PDI characteristics ............................................................................................111
36.13Power-on reset characteristics ..........................................................................111
36.14Bandgap and internal 1.0V characteristics ........................................................112
36.15Reset pin characteristics ...................................................................................113
37 Errata ..................................................................................................... 114
37.1ATxmega16A4U, ATxmega32A4U ......................................................................114
38 Datasheet Revision History ................................................................ 115
38.18387A – 07/11 .....................................................................................................115
Table of Contents....................................................................................... i
Atmel Corporation
2325 Orchard Parkway
San Jose, CA 95131
USA
Tel: (+1)(408) 441-0311
Fax: (+1)(408) 487-2600
www.atmel.com
Atmel Asia Limited
Unit 1-5 & 16, 19/F
BEA Tower, Millennium City 5
418 Kwun Tong Road
Kwun Tong, Kowloon
HONG KONG
Tel: (+852) 2245-6100
Fax: (+852) 2722-1369
Atmel Munich GmbH
Business Campus
Parkring 4
D-85748 Garching b. Munich
GERMANY
Tel: (+49) 89-31970-0
Fax: (+49) 89-3194621
Atmel Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
JAPAN
Tel: (+81)(3) 3523-3551
Fax: (+81)(3) 3523-7581
© 2011 Atmel Corporation. All rights reserved.
Atmel ®, Atmel logo and combinations thereof, AVR ®, QTouch ®, QMatrix®, AVR Studio ® and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Windows ® and others are registered trademarks of Microsoft Corporation in U.S. and
other countries. Other terms and product names may be trademarks of others.
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to
any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL
TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY
EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT,
INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice.
Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.
8387A–AVR–07/11
Similar pages