Murata NMH2405SC Isolated 2w dual output dc/dc converter Datasheet

NMH Series
www.murata-ps.com
Isolated 2W Dual Output DC/DC Converters
„
Efficiency up to 86%
„
Wide temperature performance at full
2 watt load, –40°C to 85°C
„
Dual output from a single input rail
„
Industry standard pinout
„
Power sharing on output
„
1kVDC isolation ‘Hi Pot Test’
„
5V, 12V, 24V & 48V input
„
5V, 9V, 12V and 15V output
„
Internal SMD construction
„
No external components required
„
MTTF up to 1.5 million hours
„
No electrolytic or tantalum capacitors
„
Pin compatible with MEA1 series
DESCRIPTION
The NMH series of industrial temperature range
DC/DC converters are the standard buliding blocks
for on-board point-of-use power systems. They
are ideally suited for providing dual rail supplies
on single rail boards with the added benefit of
galvanic isolation to reduce circuit noise. All of
the rated power may be drawn from a single pin
provided the total load does not exceed 2 watts.
Pin compatibility with the NMA 1 watt series
ensures minimal effort in upgrading distributed
power systems.
NMH0505DC
NMH0509DC
NMH0512DC
NMH0515DC
NMH0505SC
NMH0509SC
NMH0512SC
NMH0515SC
NMH1205DC
NMH1209DC
NMH1212DC
NMH1215DC
NMH1205SC
NMH1209SC
NMH1212SC
NMH1215SC
NMH2405DC
NMH2409DC
NMH2412DC
NMH2415DC
NMH2405SC
NMH2409SC
NMH2412SC
NMH2415SC
5
5
5
5
5
5
5
5
12
12
12
12
12
12
12
12
24
24
24
24
24
24
24
24
mA
±5
±9
±12
±15
±5
±9
±12
±15
±5
±9
±12
±15
±5
±9
±12
±15
±5
±9
±12
±15
±5
±9
±12
±15
±200
±111
±83
±67
±200
±111
±83
±67
±200
±111
±83
±67
±200
±111
±83
±67
±200
±111
±83
±67
±200
±111
±83
±67
500
494
488
476
500
494
488
476
208
201
198
198
208
201
198
198
103
98
97
97
103
98
97
97
Isolation
MTTF1
Capacitance
%
pF
kHrs
80
81
82
84
80
81
82
84
80
83
84
84
80
83
84
84
81
85
86
86
81
85
86
86
24
28
30
33
24
28
30
33
35
55
63
66
35
55
63
66
41
75
95
104
41
75
95
104
1574
663
338
187
1574
663
338
187
490
343
229
148
490
343
229
148
318
249
183
127
318
249
183
127
DIP
SIP
DIP
SIP
DIP
SIP
Recommended
Alternative
NMH4805DC
NMH4809DC
NMH4812DC
NMH4815DC
NMH4805SC
NMH4809SC
NMH4812SC
NMH4815SC
48
48
48
48
48
48
48
48
±5
±9
±12
±15
±5
±9
±12
±15
±200
±111
±83
±67
±200
±111
±83
±67
51
51
49
49
51
51
49
49
82
82
85
85
82
82
85
85
45
74
90
112
45
74
90
112
235
195
152
112
235
195
152
112
Contact Your Local Sales Rep
FEATURES
V
Input
Current at
Rated Load
mA
Output Output
Voltage Current
Package
Style
Order Code
Nominal
Input
Voltage
V
Efficiency
SELECTION GUIDE
DIP
SIP
INPUT CHARACTERISTICS
Parameter
Voltage range
Reflected ripple current
For full details go to
www.murata-ps.com/rohs
Conditions
Min.
Typ.
Max.
Units
Continuous operation, 5V input types
Continuous operation, 12V input types
Continuous operation, 24V input types
Continuous operation, 48V input types
5V input types
12V input types
24V input types
48V input types
4.5
10.8
21.6
43.2
5
12
24
48
50
70
130
200
5.5
13.2
26.4
52.8
V
mA p-p
1. Calculated using MIL-HDBK-217F with nominal input voltage at full load.
All specifications typical at TA=25°C, nominal input voltage and rated output current unless otherwise specified.
www.murata-ps.com/support
KDC_NMH.F02 Page 1 of 6
NMH Series
Isolated 2W Dual Output DC/DC Converters
OUTPUT CHARACTERISTICS
Parameter
Rated Power
Voltage Set Point Accuracy
Line regulation
Load Regulation
Ripple and Noise
Conditions
TA=-40°C to 85°C, see derating graph
Min.
NMH0505DC/SC
All other types
High VIN to low VIN
10% load to rated load, 5V output types
10% load to rated load, 9V output types
10% load to rated load, 12V output types
10% load to rated load, 15V output types
BW=DC to 20MHz, 5V output types
BW=DC to 20MHz, 9V output types
BW=DC to 20MHz, 12V output types
BW=DC to 20MHz, 15V output types
-5
-5
Typ.
Max.
Units
W
1.0
5
2
7.5
5
1.2
10
3
10
150
100
80
70
200
150
150
150
mV p-p
Max.
Units
%
%/%
%
ABSOLUTE MAXIMUM RATINGS
Lead temperature 1.5mm from case for 10 seconds
Input voltage VIN, NMH05 types
Input voltage VIN, NMH12 types
Input voltage VIN, NMH24 types
Input voltage VIN, NMH48 types
260°C
7V
15V
28V
54V
ISOLATION CHARACTERISTICS
Parameter
Conditions
Min.
Typ.
Isolation test voltage
Resistance
Flash tested for 1 second
Viso= 500V
1000
1
10
Parameter
Conditions
Min.
Typ.
Switching frequency
5V input types
12V input types
24V & 48V input types
VDC
GΩ
GENERAL CHARACTERISTICS
Max.
95
90
80
Units
kHz
TEMPERATURE CHARACTERISTICS
Parameter
Conditions
Min.
Specification
Storage
All output types
-40
-50
Case Temperature above ambient
Cooling
5V output types
12V output types
Free air convection
Output Voltage
Output Power (W)
85°C
Safe Operating Area
+5%
VNOM
Units
°C
100
50
0
Ambient Temperature (°C)
150
Typical
L
oad Line
+2.5%
-2.5%
-7.5%
10
0
-40
85
130
TOLERANCE ENVELOPE
+10%
3
1
Max.
30
25
TEMPERATURE DERATING GRAPH
2
Typ.
75
50
25
Output Load Current (%)
100
The voltage tolerance envelope shows typical load regulation characteristics for this
product series. The tolerance envelope is the maximum output voltage variation due
to changes in output loading.
www.murata-ps.com/support
KDC_NMH.F02 Page 2 of 6
NMH Series
Isolated 2W Dual Output DC/DC Converters
TECHNICAL NOTES
ISOLATION VOLTAGE
‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Voltage’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’ are all terms that relate to the same thing, a test voltage,
applied for a specified time, across a component designed to provide electrical isolation, to verify the integrity of that isolation.
Murata Power Solutions NMH series of DC/DC converters are all 100% production tested at their stated isolation voltage. This is 1kVDC for 1 second.
A question commonly asked is, “What is the continuous voltage that can be applied across the part in normal operation?”
For a part holding no specific agency approvals, such as the NMH series, both input and output should normally be maintained within SELV limits i.e. less than 42.4V peak, or
60VDC. The isolation test voltage represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation system. The part
could be expected to function correctly with several hundred volts offset applied continuously across the isolation barrier; but then the circuitry on both sides of the barrier must
be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circuits and any user-accessible circuitry according to
safety standard requirements.
REPEATED HIGH-VOLTAGE ISOLATION TESTING
It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials,
construction and environment. The NMH series has toroidal isolation transformers, with no additional insulation between primary and secondary windings of enameled wire. While
parts can be expected to withstand several times the stated test voltage, the isolation capability does depend on the wire insulation. Any material, including this enamel (typically
polyurethane) is susceptible to eventual chemical degradation when subject to very high applied voltages thus implying that the number of tests should be strictly limited. We
therefore strongly advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be reduced by 20% from specified test voltage.
This consideration equally applies to agency recognised parts rated for better than functional isolation where the wire enamel insulation is always supplemented by a further
insulation system of physical spacing or barriers.
RoHS COMPLIANCE INFORMATION
This series is compatible with RoHS soldering systems with a peak wave solder temperature of
260°C for 10 seconds. The pin termination finish on the SIP package type is Tin Plate, Hot Dipped
over Matte Tin with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in
this series are backward compatible with Sn/Pb soldering systems.
For further information, please visit www.murata-ps.com/rohs
APPLICATION NOTES
Minimum load
The minimum load to meet datasheet specification is 10% of the full rated load across the specified input voltage range. Lower than 10% minimum loading will result in
an increase in output voltage, which may rise to typically double the specified output voltage if the output load falls to less than 5%.
Capacitive loading and start up
Typical start up times for this series, with a typical input voltage rise time of 2.2μs and output capacitance of 10μF, are shown in the table below. The product
series will start into a capacitance of 47μF with an increased start time, however, the maximum recommended output capacitance is 10μF.
NMH0505SC
NMH0509SC
NMH0512SC
NMH0515SC
NMH1205SC
NMH1209SC
NMH1212SC
NMH1215SC
Start-up time
μs
1072
2481
3546
5380
672
1152
1580
3150
NMH2405SC
NMH2409SC
NMH2412SC
NMH2415SC
NMH4805SC
NMH4809SC
NMH4812SC
NMH4815SC
Start-up time
μs
1064
1544
4398
4230
966
1220
2822
4275
Typical Start-Up Wave Form
www.murata-ps.com/support
KDC_NMH.F02 Page 3 of 6
NMH Series
Isolated 2W Dual Output DC/DC Converters
APPLICATION NOTES (continued)
Ripple & Noise Characterisation Method
Ripple and noise measurements are performed with the following test configuration.
C1
1μF X7R multilayer ceramic capacitor, voltage rating to be a minimum of 3 times the output voltage of the DC/DC converter
10μF tantalum capacitor, voltage rating to be a minimum of 1.5 times the output voltage of the DC/DC converter with an ESR of less
C2
than 100mΩ at 100 kHz
C3
100nF multilayer ceramic capacitor, general purpose
R1
450Ω resistor, carbon film, ±1% tolerance
R2
50Ω BNC termination
T1
3T of the coax cable through a ferrite toroid
RLOAD
Resistive load to the maximum power rating of the DC/DC converter. Connections should be made via twisted wires
Measured values are multiplied by 10 to obtain the specified values.
Differential Mode Noise Test Schematic
DC/DC Converter
OSCILLOSCOPE
C1 C2 C3
+
SUPPLY
Input
-
R1
R2
T1
+
Y INPUT
Output
-
R LOAD
OUTPUT RIPPLE REDUCTION
By using the values of inductance and capacitance stated, the output ripple at the rated load is lowered to 5mV p-p max.
Component selection
Capacitor: Ceramic chip capacitors are recommended. It is required that the ESR (Equivalent Series Resistance) should be as low as possible, X7R types are recommended.
The voltage rating should be at least twice (except for 15V output), the rated output voltage of the DC/DC converter.
Inductor: The rated current of the inductor should not be less than that of the output of the DC/DC converter. At the rated current, the DC resistance of the inductor should be
such that the voltage drop across the inductor is <2% of the rated voltage of the DC/DC converter. The SRF (Self Resonant Frequency) should be >20MHz.
L
Power
Source
Order Code
L (μH)
NMH0505XC
NMH0509XC
NMH0512XC
NMH0515XC
NMH1205XC
NMH1209XC
NMH1212XC
NMH1215XC
NMH2405XC
NMH2409XC
NMH2412XC
NMH2415XC
NMH4805XC
NMH4809XC
NMH4812XC
NMH4815XC
47
47
150
100
47
47
150
100
47
47
150
100
47
47
150
100
DC
C
Load
DC
Inductor Order Codes
SMD
Through Hole
82473C
11R473C
82473C
11R473C
82154C
11R154C
82104C
11R104C
82473C
11R473C
82473C
11R473C
82154C
11R154C
82104C
11R104C
82473C
11R473C
82473C
11R473C
82154C
11R154C
82104C
11R104C
82473C
11R473C
82473C
11R473C
82154C
11R154C
82104C
11R104C
C (μF)
4.7
2.2
3.3
3.3
4.7
2.2
3.3
3.3
4.7
2.2
3.3
3.3
4.7
2.2
3.3
3.3
Product specification for MPS inductors can be found at:
1100R Series (Through Hole)
http://www.murata-ps.com/data/magnetics/kmp_1100r.pdf
8200 Series (SMD)
http://www.murata-ps.com/data/magnetics/kmp_8200c.pdf
www.murata-ps.com/support
KDC_NMH.F02 Page 4 of 6
NMH Series
Isolated 2W Dual Output DC/DC Converters
PACKAGE SPECIFICATIONS
MECHANICAL DIMENSIONS
PIN CONNECTIONS - 14 PIN DIP
SIP package
DIP package
19.50 [0.77]
19.50 [0.77]
NMH0505DC
10.00 [0.40]
7.70 [0.303]
NMH0505SC
0.40 [0.016] MIN
XYYWW
XYYWW
4.10±0.50 [0.161±0.020]
4.10±0.50 [0.161±0.020]
2.37
2.08
7.62 [0.300]
0.50±0.05 [0.020±0.002]
[0.055
0.041]
Function
1
-VIN
7
NC
8
OV
7.50 [0.295]
9.80 [0.386]
1.40
1.04
Pin
[0.093
0.082 ]
1
14
1
2
4
0.50±0.05 [0.020±0.002]
5
6
2.54 [0.100]
7
11
9
8
0.25±0.05 [0.010±0.002]
7.62 [0.300]
15.24 [0.600]
1.45
1.00
[ ]
2.52
1.54
[ ]
0.057
0.039
0.099
0.061
12.70 [0.500]
9
+VOUT
11
-VOUT
14
+VIN
PIN CONNECTIONS - 7 PIN SIP
Pin
Function
1
+VIN
2
-VIN
4
-VOUT
5
OV
6
+VOUT
0.25±0.05 [0.010±0.002]
Unless otherwise stated all dimensions in mm (inches) ±0.25mm (0.010”). Controlling dimension is mm.
All pins on a 2.54mm (0.100”) pitch and within 0.25mm (0.010”) of true position.
Weight: 2.85g (DIP) 2.76g (SIP)
www.murata-ps.com/support
KDC_NMH.F02 Page 5 of 6
NMH Series
Isolated 2W Dual Output DC/DC Converters
PACKAGE SPECIFICATIONS (continued)
RECOMMENDED FOOTPRINT DETAILS
7 Pin SIP Package
14 Pin DIP Package
x5 HOLES
Ø1.00 [Ø0.039]
x6 HOLES
Ø1.00 [Ø0.039]
2.54 [0.100]
2.54 [0.100]
2.54 [0.100]
2.54 [0.100]
TUBE OUTLINE DIMENSIONS
14 Pin DIP Tube
7 Pin SIP Tube
9.3 [0.366]
12.0 [0.472]
12.43 [0.489]
14.5 [0.571]
18.0 [0.709]
5.07±0.80 [0.200±0.03]
5.05 [0.199]
Unless otherwise specified all dimensions in mm [inches] ±0.55mm [0.022].Tube
length (14 Pin DIP) : 520mm [20.472] ±2.0 [0.079].
Tube length (7 Pin SIP) : 520mm [20.472] ±2.0 [0.079].
Murata Power Solutions, Inc.
11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A.
ISO 9001 and 14001 REGISTERED
5.0 [0.197]
Tube Quantity : 25
This product is subject to the following operating requirements
and the Life and Safety Critical Application Sales Policy:
Refer to: http://www.murata-ps.com/requirements/
Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other
technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply
the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without
notice.
© 2017 Murata Power Solutions, Inc.
www.murata-ps.com/support
KDC_NMH.F02 Page 6 of 6
Similar pages