MP5610 2.7V to 5.5V Input, 1.2MHz, Dual-ch LCD Bias Power Supply FEATURES DESCRIPTION The MP5610 is a dual-output converter with 2.7V-to-5.5V input for small size LCD panel bias supply. It uses peak-current mode to regulate the positive output voltage and uses a negative charge pump to provide negative output voltage. The MP5610 has very good efficiency performance because the negative charge pump draws power directly from the positive converter switching node which can save power loss much. Also, MP5610 provides good voltage tracking between positive and negative output by well matching the internal MOSFET on resistance value. The fully integrated synchronous rectification increases total efficiency and reduces PCB space requirements. The MP5610 features as programmable output, fixed 1.2MHz switching frequency and rich protection modes, like input-output disconnection protection, cycle-by-cycle current limit protection, thermal shutdown protection, Output over voltage protection and Output under voltage protection. The MP5610 is available in tiny QFN-10 (1.4mmx1.8mm) package. 2.7V-to-5.5V Input Voltage Max. 50mA Output Current for Each Output Up to Programmable 5.8V Output Voltage 0.5% Line Regulation for Step-up Converter 0.5% Load Regulation for Step-up Converter 1% Voltage Tracking Between Dual-ch 600mV Feedback Voltage with ±1% Accuracy 270us Soft Start Time Input DC Current Limit Protection Output Over Voltage Protection Output Under Voltage Protection Input UVLO Protection Over Temperature Protection Available in a QFN-10 (1.4mm×1.8mm) Package APPLICATIONS Feature Phones and Smart Phones Small Size LCD Displays All MPS parts are lead-free, halogen free, and adhere to the RoHS directive. For MPS green status, please visit MPS website under Quality Assurance. “MPS” and “The Future of Analog IC Technology” are Registered Trademarks of Monolithic Power Systems, Inc. TYPICAL APPLICATION L1 10μH VINP SW +5.4V C5 2.2μF VOP 2.7V~4.5V C2 2.2μF VIN C1 2.2μF R1 FBP EN 100k R2 12.4k EN C3 -5.4V CP1 2.2μF MP5610 Rev. 1.02 12/6/2016 CP2 VON GND C4 2.2μF www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 1 MP5610 – 2.7V TO 5.5V INPUT, 1.2MHz, DUAL-CH, LCD BIAS POWER SUPPLY ORDERING INFORMATION Part Number* MP5610GQG Package QFN-10 (1.4mm×1.8mm) Top Marking BZ * For Tape & Reel, add suffix –Z (e.g. MP5610GQG–Z); PACKAGE REFERENCE TOP VIEW VIN VINP SW 10 9 8 EN 1 7 VOP FBP 2 6 GND 3 4 5 VON CP2 CP1 QFN-10 (1.4mm×1.8mm) ABSOLUTE MAXIMUM RATINGS (1) Thermal Resistance VIN, VINP ....................................... -0.3V to +6.5V VSW, VOP, VCP1…………………..…-0.3V to +7V VCP2, VON ........................................ -7V to +0.3V All Other Pins .............................. -0.3V to +6.5V Junction Temperature .............................. 150°C Lead Temperature ................................... 260°C (2) Continuous Power Dissipation ... (TA = 25°C) QFN-10 (1.4mm×1.8mm) ...................... 0.892W QFN-10 (1.4mm×1.8mm) ..... 140 ...... 30 °C/W Recommended Operating Conditions (3) Supply Voltage VIN ......................... 2.7V to 5.5V Operating Junction Temp. ........ -40°C to +125°C MP5610 Rev. 1.02 12/6/2016 (4) θJA θJC Notes: 1) Exceeding these ratings may damage the device. 2) The maximum allowable power dissipation is a function of the maximum junction temperature TJ (MAX), the junction-toambient thermal resistance θJA, and the ambient temperature TA. The maximum allowable continuous power dissipation at any ambient temperature is calculated by PD (MAX) = (TJ (MAX)-TA)/θJA. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. Internal thermal shutdown circuitry protects the device from permanent damage. 3) The device is not guaranteed to function outside of its operating conditions. 4) Measured on JESD51-7, 4-layer PCB. www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 2 MP5610 – 2.7V TO 5.5V INPUT, 1.2MHz, DUAL-CH, LCD BIAS POWER SUPPLY ELECTRICAL CHARACTERISTICS VIN =3.7V, VEN = VIN, TA = 25°C, unless otherwise noted. Parameters Symbol Condition Min Typ Max Units 5.5 V 500 μA 0.2 μA 2.55 V GENEARL Operating Input Voltage VIN Supply Current (Quiescent) IQ VIN=3.7V, VEN= VIN, no switching Supply Current (Shutdown) IST VEN=0V, VIN=3.7V Input UVLO Threshold VIN_UVLO 2.7 Rising Edge 450 2.35 Input UVLO Hysteresis 260 EN High Voltage VEN_HIGH VEN Rising EN Low Voltage VEN_LOW VEN Falling Switching Frequency Input Disconnect MOSFET OnResistance Input DC Current Limit 2.45 fSW RON_M5 ILIM_IN Input DC Current Ramp Time REF Soft Start Time 1.2 0.96 VIN=3.7V VIN=3.7V VIN=3.7V, VINP=GND ILIM_IN: 0 to 260mA VIN=3.7V mV V 1.2 0.4 V 1.44 MHz Ω 0.1 200 245 290 mA 215 us 270 us 85 % 110 ns STEP-UP CONVERTER Maximum Duty Cycle Minimum On Time Feedback Regulation Voltage DMAX 75 tON_MIN VFBP 594 600 Feedback Input Bias Current Main Switch On-Resistance High Side Switch On-Resistance Cycle-by-Cycle Current Limit High Side Switch Current ZCD Detection Threshold NEGATIVE CHARGE PUMP CP2 to GND MOSFET OnResistance CP2 to VON MOSFET OnResistance PROTECTION Positive Output Over Voltage Protection Threshold Output Over Voltage Protection Hysteresis Negative Output Over Voltage Protection Threshold Output Over Voltage Protection Hysteresis MP5610 Rev. 1.02 12/6/2016 606 mV 100 nA RON_M1 VIN=2.7V-3.7V, 0.5 Ω RON_M2&M6 VIN=2.7V-3.7V, 2.0 Ω ILIM Duty Cycle=0% 240 300 365 mA 5 10 15 mA RON_M3 VIN=2.7V-3.7V, 0.6 Ω RON_M4 VIN=2.7V-3.7V, 0.5 Ω VOVP 5.9 VOVP_TH VOVN 6.1 6.4 215 -6.7 -6.2 V mV -5.8 165 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. V mV 3 MP5610 – 2.7V TO 5.5V INPUT, 1.2MHz, DUAL-CH, LCD BIAS POWER SUPPLY ELECTRICAL CHARACTERISTICS (continued) VIN =3.7V, VEN = VIN, TA = 25°C, unless otherwise noted. Parameters Symbol PROTECTION (continued) Positive Output Under-Voltage Protection Threshold Negative Output Under-Voltage Protection Threshold OTP Protection Threshold MP5610 Rev. 1.02 12/6/2016 Condition Min Typ Max Units VUVP_P 52% REF VUVP_N 60% VOP Tj_SD 150 ℃ www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 4 MP5610 – 2.7V TO 5.5V INPUT, 1.2MHz, DUAL-CH, LCD BIAS POWER SUPPLY TYPICAL PERFORMANCE CHARACTERISTICS VIN = 3.7V, VOP=+5.4V, VON=-5.4V, L = 10µH, COUT=1µF, TA = 25°C, unless otherwise noted. MP5610 Rev. 1.02 12/6/2016 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 5 MP5610 – 2.7V TO 5.5V INPUT, 1.2MHz, DUAL-CH, LCD BIAS POWER SUPPLY TYPICAL PERFORMANCE CHARACTERISTICS (continued) VIN = 3.7V, VOP=+5.4V, VON=-5.4V, L = 10µH, COUT=1µF, TA = 25°C, unless otherwise noted. MP5610 Rev. 1.02 12/6/2016 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 6 MP5610 – 2.7V TO 5.5V INPUT, 1.2MHz, DUAL-CH, LCD BIAS POWER SUPPLY TYPICAL PERFORMANCE CHARACTERISTICS (continued) VIN = 3.7V, VOP=+5.4V, VON=-5.4V, L = 10µH, COUT=1µF, TA = 25°C, unless otherwise noted. Notes: (a) Line/Load Regulation: (VOP-VOP_AVG)/VOP_AVG*100%. (b) Voltage Tracking: (|VON|-VOP)/VOP*100%. MP5610 Rev. 1.02 12/6/2016 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 7 MP5610 – 2.7V TO 5.5V INPUT, 1.2MHz, DUAL-CH, LCD BIAS POWER SUPPLY TYPICAL PERFORMANCE CHARACTERISTICS (continued) VIN = 3.7V, VOP=+5.4V, VON=-5.4V, L = 10µH, COUT=1µF, TA = 25°C, unless otherwise noted. MP5610 Rev. 1.02 12/6/2016 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 8 MP5610 – 2.7V TO 5.5V INPUT, 1.2MHz, DUAL-CH, LCD BIAS POWER SUPPLY PIN FUNCTIONS Package Pin # Name 1 EN IC Enable Pin. A voltage higher than threshold voltage enables the IC. Disable the IC by pulling this pin to GND. 2 FBP Positive Output Step-up Converter Feedback Pin. 3 4 VON CP2 5 CP1 6 7 GND VOP Charge Pump Negative Output Pin. Negative Output Charge Pump Flying Capacitor Node 2 Negative Output Charge Pump Flying Capacitor Node 1. Connect a flying capacitor between this pin and CP2 pin. Ground Reference Pin. Step-up Converter Positive Output Pin. 8 SW Step-up Converter Power Switch Node. Drain of the internal low-side MOSFET. Connect the power inductor between SW and VINP pin. 9 VINP Input Power Pin for Step-up Power Stage. Internally connected to the source node of internal N-MOSFET. 10 VIN MP5610 Rev. 1.02 12/6/2016 Description Input Power Pin. It provides power for internal logic and driver. Must be locally bypassed. www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 9 MP5610 – 2.7V TO 5.5V INPUT, 1.2MHz, DUAL-CH, LCD BIAS POWER SUPPLY FUNCTIONAL BLOCK DIAGRAM Figure 1: Functional Block Diagram MP5610 Rev. 1.02 12/6/2016 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 10 MP5610 – 2.7V TO 5.5V INPUT, 1.2MHz, DUAL-CH, LCD BIAS POWER SUPPLY OPERATION Positive Step-up Converter The MP5610 uses peak-current-mode control step up converter to regulate positive output voltage. The output voltage is accurately set a resistor divider. At the start of each oscillator cycle, the control circuit turns on the low-side MOSFET (M1) and the inductor current stars ramping up. A stabilizing ramp added to the output of the current-sense amplifier, which then feeds into the positive input of the PWM comparator, prevents sub-harmonic oscillations at duty cycles greater than 50%. When the input to the PWM comparator equals the output voltage of the error amplifier, M1 turns off. Then the inductor current flows through the synchronous power MOSFET which forces the inductor current to decrease. Negative Charge Pump The negative output is provided by a charge pump which directly draws power from the stepup converter switching node. When the M1 turns on, CP2-to-VON MOSFET (M4) turns on at the same time and then, the energy stored in flying capacitor is transferred to the output capacitor and load. When step-up rectifier MOSFET (M2) turns on, CP2-to-GND MOSFET (M3) turns on at the same time, the flying capacitor is charged from inductor and thus, energy is stored in flying capacitor. The negative output voltage tracks the positive output voltage by well matching the internal MOSFET on resistive. The negative voltage can be estimated as below, VON I I VOP OP * (Ron _ M2 Ron _ M6 ) ON * Ron _ M3 1 D 1 D I I ON * Ron _ M4 (IL ON ) * (Ron _ M1 Rs ) D D While, VON is the negative output voltage, VOP is the positive output voltage, ION is the negative output current, IOP is the positive output current, IL is the inductor average current, Rs is the internal sensing resistor value of stepup converter, RON_M1 is the on resistance of MOSFET M1, RON_M2 is the on resistance of MOSFET M2, RON_M3 is the on resistance of MOSFET M3, RON_M4 is the on resistance of MOSFET M4, RON_M6 is the on resistance of MOSFET M6, Enable When the input voltage is larger than undervoltage-lock-out protection threshold, MP5610 can be enabled by pulling EN pin to higher than 1.2V. Leaving EN pin float or by pulling EN pin down to GND disables MP5610. There is a 1M Ω pulling down resistor from EN pin to GND. System Startup When enabled, the input disconnection MOSFET (M5) turns on and its DC current limit ramps up gradually and this function provides two merits, 1) To avoid large inrush current during startup, 2) To provide better voltage tracking starting from 0 between positive and negative output voltage. After IC enabled, the internal reference starts ramping up linearly to provide linear voltage startup and avoid inrush current. The soft start time from 0 to 600mV is around 1ms. Voltage Tracking MP5610 does precise voltage tracking by adjusting the on resistance of PMOS M6 in close loop. If the sum of positive output voltage value and negative output voltage value is larger than 0, the gate driver voltage of M6 increases to increase the on resistance, thus more energy is dropped across M6. If the sum of positive output voltage value and negative output voltage value is lower than 0, the gate driver voltage of M6 reduces to reduces the on resistance, thus less energy is dropped across M6. Note that the minimum on resistance of M6 is 1Ω. D is the duty cycle of step-up converter, MP5610 Rev. 1.02 12/6/2016 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 11 MP5610 – 2.7V TO 5.5V INPUT, 1.2MHz, DUAL-CH, LCD BIAS POWER SUPPLY Output Over-Voltage Protection MP5610 provides over-voltage protection for step-up converter. If the positive output voltage is larger than 6.1V, IC stops switching and output starts dropping. When the voltage drops lower than OVP recover threshold, IC resumes to normal switching. The hysteresis is 215mV. Since the negative output voltage is always tracking the positive output voltage, the negative output voltage can also be avoided to over-charging. In some unexpected cases, if the negative output voltage is lower than -6.2V, IC stops switching and output starts dropping. When the voltage drops larger than OVP recover threshold, IC resumes to normal switching. The hysteresis is 165mV. VOP Under Voltage Protection After startup, if the output feedback voltage is lower than 52%*VREF, IC stops switching and latches off to avoid any damage. This fault has to be cleared by reset the input power or enable signal. If VOP and GND are shorted before the startup, larger current draws from the input power side and it can be limited by maximum input DC current limit, around 260mA. MP5610 Rev. 1.02 12/6/2016 VON Under Voltage Protection MP5610 provides VON Under Voltage protection by sensing the negative output voltage. After the startup, if the VON is lower than 60%*VOP, the IC will stop switching and latch off to avoid any damage. If the VON-to-GND is shorted before startup, the positive output voltage will not be charged up and thus, the IC will be protected by limiting the input current limit switch. Input UVLO Protection To avoid IC operation in low input voltage, MP5610 has input UVLO protection. IC only starts operation when input voltage is larger than input under-voltage-lock-out protection threshold, VIN_UVLO. There is a 260mV hysteresis when input voltage drops. Over Heat Protection When MP5610 junction temperature exceeds the thermal protection threshold, IC shuts down and latch off. www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 12 MP5610 – 2.7V TO 5.5V INPUT, 1.2MHz, DUAL-CH, LCD BIAS POWER SUPPLY APPLICATION INFORMATION Setting the Positive Output Voltage The external resistor divider is used to set the output voltage. Choose the high side feedback resistor R1 to 100k to 200k resistor, the low side feedback resistor R2 can be calculated as below, R2 R1 VOUT 1 0.6 Selecting the Input Capacitor The input capacitor reduces the surge current drawn from the input supply and the switching noise from the device. The input capacitor impedance at the switching frequency should be less than the input source impedance to prevent the high-frequency switching current from passing through to the input. Use ceramic capacitors with X5R or X7R dielectrics for their low ESR and small temperature coefficients. For most applications, use a 1µF-to-4.7μF ceramic capacitor. Selecting the Inductor The MP5610 requires an inductor to boost its output voltage. A larger value inductor results in less ripple current, lowering both the peakinductor current and the stress on the internal Nchannel MOSFET. However, the larger inductor is physically larger, has a higher series resistance, and a lower saturation current. Choose an inductor that does not saturate under the worst-case load conditions. Select the minimum inductor value to ensure that the boost converter works in continuous-conduction mode with high efficiency and good EMI performance. Calculate the required inductance value using the equation: η VOUT D (1 D)2 L 2 fSW ILOAD MP5610 Rev. 1.02 12/6/2016 D 1 VIN VOUT Where VIN and VOUT are the input and output voltages, fSW is the switching frequency, ILOAD is the load current, and η is the efficiency. Selecting the Output Capacitor The output capacitor keeps the output voltage ripple small and ensures feedback loop stability. The output capacitor impedance must be low at the switching frequency. Ceramic capacitors with X7R dielectrics are recommended for their low ESR characteristics. Selection must also account for the capacitance’s dependence on the voltage rating; with a DC bias voltage, the capacitor can lose as much as 50% of its capacitance at its rated voltage rating. Leave a sufficient voltage rating margin when select the component. Too-low or too-high capacitance will cause loop instability. For most applications, select a capacitor in the range of 1μF to 4.7μF. Selecting Flying Capacitor The flying capacitor between CP1 and CP2 is used to transfer energy from step-up converter switching node to negative output. Ceramic capacitors with X7R dielectrics are recommended for their low ESR characteristics. Usually, a 0.1μF to 1μF capacitor can cover most of the applications. Layout Consideration Careful attention must be paid to the PCB board layout and components placement. Proper layout of the high frequency switching path is critical to prevent noise and limit electromagnetic interference. The loop consisting of internal lowside MOSFET, synchronous MOSFET and output capacitor contains a high-frequency ripple current—minimize this loop. Place the input and output capacitor should as close to the IC as possible. www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 13 MP5610 – 2.7V TO 5.5V INPUT, 1.2MHz, DUAL-CH, LCD BIAS POWER SUPPLY TYPICAL APPLICATION CIRCUITS L1 10μH VINP SW +5.4V C5 2.2μF VOP 2.7V~4.5V C2 2.2μF VIN C1 2.2μF R1 FBP EN 100k R2 12.4k EN C3 -5.4V CP1 2.2μF CP2 VON GND C4 2.2μF Figure 2: Application Circuit MP5610 Rev. 1.02 12/6/2016 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 14 MP5610 – 2.7V TO 5.5V INPUT, 1.2MHz, DUAL-CH, LCD BIAS POWER SUPPLY PACKAGE INFORMATION QFN-10 (1.4mm×1.8mm) NOTICE: The information in this document is subject to change without notice. Please contact MPS for current specifications. Users should warrant and guarantee that third party Intellectual Property rights are not infringed upon when integrating MPS products into any application. MPS will not assume any legal responsibility for any said applications. MP5610 Rev. 1.02 12/6/2016 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. 15