API BX3110PM Rf amplifier model Datasheet

RF AMPLIFIER
MODEL TM3110PM
Available as:
Features
Typical Intermodulation Performance at 25 ºC
„ Superior Phase Noise Performance
„ High Output Power: +30 dBm Typical
„ Operating Temp. -55 ºC to +85 ºC
„ Environmental Screening Available
Second Order Harmonic Intercept Point ...... +66 dBm (Typ.)
Second Order Two Tone Intercept Point ....... +63 dBm (Typ.)
Third Order Two Tone Intercept Point ........... +45 dBm (Typ.)
Absolute Maximum (No Damage) Ratings
Ambient Operating Temperature ................ -55ºC to +100 ºC
Storage Temperature ................................. -62ºC to +125 ºC
Case Temperature .................................................. +125 ºC
DC Voltage .......................................................... +17 Volts
Continuous RF Input Power .................................. +15 dBm
Short Term RF Input Power ........... 100 mW (1 Minute Max.)
Maximum Peak Power .................... 0.2 Watt (3 µsec Max.)
Specifications
CHARACTERISTIC
Frequency (MHz)
TYPICAL
Ta= 25 ºC
MIN/MAX
Ta = -55 ºC to +85 ºC
10 - 200 MHz
10 - 200 MHz
Gain (dB)
15.5
15 Min.
Power @ 1 dB
Comp. (dBm)
+30
+29 Min.
-17
1.8:1
1.8:1
3.5
-16 Max.
2.0:1 Max.
2.0:1 Max.
4.5 Max.
+15
240
+15
250 Max.
Reverse Isolation (dB)
VSWR
In
Out
Noise Figure (dB)
Power
Vdc
mA
TM3110PM, 4 Pin TO-8 (T4)
TN3110PM, 4 Pin Surface Mount (SM3)
BX3110PM, Connectorized Housing (H1)
Guaranteed @ 25 ºC (160 MHz) Phase Noise Performance (dBc/Hz)*
Frequency
Typical
-160
-170
-175
-180
-180
100 Hz
1 kHz
10 kHz
100 kHz
1 MHz
Note: Care should always be taken to effectively ground the case of each unit.
Guarantee
-155
-165
-170
-175
-175
*Note: Phase Noise Performance typically tested at midband.
Bandedge performance may vary.
Typical Performance Data
Gain (dB)
18
Reverse Isolation (dB)
0
17
-10
16
-20
15
-30
14
Start 10 MHz
+32
Stop 200 MH z
1 dB Comp. (dBm)
+30
4
+29
+28
3
2.0
Input VSWR
Stop 200 MHz
Start 10 MHz
Noise Figure (dB)
Stop 2 00 MHz
-1 70
-19 0
10 0
2
Start 10 MHz
Output VSWR
Stop 2 00 MHz
Legend
Stop 20 0 MHz
+25 ºC
1.5
Start 1 0 MHz
1k
10 k
100k
1M
Typical
Residual Phase Noise Test Conditions:
„ Carrier Frequency: 160 MHz
„ Power Output +29.0 dBm
„ Temperature: 25 oC
1.75
Sta rt 10 MH z
-1 60
-1 80
2.0
1.75
1.5
-1 50
6
5
Sta rt 10 MH z
-1 40
-40
+31
Phase Noise (dBc/Hz)
-13 0
Stop 2 00 MHz
„ Agilent ES5500 System
+85 ºC - - - - - - -55 ºC
Spectrum Microwave · 2144 Franklin Drive N.E. · Palm Bay, Florida 32905 · PH (888) 553-7531 · Fax (888) 553-7532
Rev.
4/26/10
www.SpectrumMicrowave.com Spectrum Microwave · 2707 Black Lake Place · Philadelphia, Pennsylvania 19154 · PH (215) 464-4000 · Fax (215) 464-4001
Similar pages