IDT IDT54FCT162823CTPA Fast cmos 18-bit register Datasheet

FAST CMOS 18-BIT
REGISTER
IDT54/74FCT16823AT/BT/CT/ET
IDT54/74FCT162823AT/BT/CT/ET
Integrated Device Technology, Inc.
FEATURES:
DESCRIPTION:
• Common features:
– 0.5 MICRON CMOS Technology
– High-speed, low-power CMOS replacement for
ABT functions
– Typical tSK(o) (Output Skew) < 250ps
– Low input and output leakage ≤1µA (max.)
– ESD > 2000V per MIL-STD-883, Method 3015;
> 200V using machine model (C = 200pF, R = 0)
– Packages include 25 mil pitch SSOP, 19.6 mil pitch
TSSOP, 15.7 mil pitch TVSOP and 25 mil pitch Cerpack
– Extended commercial range of -40°C to +85°C
– VCC = 5V ±10%
• Features for FCT16823AT/BT/CT/ET:
– High drive outputs (-32mA IOH, 64mA IOL)
– Power off disable outputs permit “live insertion”
– Typical VOLP (Output Ground Bounce) < 1.0V at
VCC = 5V, TA = 25°C
• Features for FCT162823AT/BT/CT/ET:
– Balanced Output Drivers: ±24mA (commercial),
±16mA (military)
– Reduced system switching noise
– Typical VOLP (Output Ground Bounce) < 0.6V at
VCC = 5V,TA = 25°C
The FCT16823AT/BT/CT/ET and FCT162823AT/BT/CT/
ET 18-bit bus interface registers are built using advanced,
dual metal CMOS technology. These high-speed, low-power
registers with clock enable (xCLKEN) and clear (xCLR) controls are ideal for parity bus interfacing in high-performance
synchronous systems. The control inputs are organized to
operate the device as two 9-bit registers or one 18-bit register.
Flow-through organization of signal pins simplifies layout. All
inputs are designed with hysteresis for improved noise margin.
The FCT16823AT/BT/CT/ET are ideally suited for driving
high-capacitance loads and low-impedance backplanes. The
output buffers are designed with power off disable capability
to allow "live insertion" of boards when used as backplane
drivers.
The FCT162823AT/BT/CT/ET have balanced output drive
with current limiting resistors. This offers low ground bounce,
minimal undershoot, and controlled output fall times – reducing the need for external series terminating resistors. The
FCT162823AT/BT/CT/ET are plug-in replacements for the
FCT16823AT/BT/CT/ET and ABT16823 for on-board interface applications.
FUNCTIONAL BLOCK DIAGRAM
1OE
2OE
1CLR
2CLR
1CLK
2CLK
1CLKEN
2CLKEN
R
C
D
R
C
D
1Q1
1D1
2Q1
2D1
TO 8 OTHER CHANNELS
2772 drw 01
TO 8 OTHER CHANNELS
2772 drw 02
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
MILITARY AND COMMERCIAL TEMPERATURE RANGES
1996 Integrated Device Technology, Inc.
5.16
AUGUST 1996
DSC-2772/8
1
IDT54/74FCT16823AT/BT/CT/ET, 162823AT/BT/CT/ET
FAST CMOS 18-BIT REGISTER
MILITARY AND COMMERCIAL TEMPERATURE RANGES
PIN CONFIGURATIONS
1CLR
1
56
1CLK
1CLKEN
1OE
2
55
1CLKEN
54
1D1
1Q1
3
54
1D1
4
53
GND
GND
4
53
GND
1Q2
5
52
1D2
1Q2
5
52
1D2
1Q3
6
51
1D3
1Q3
6
51
1D3
VCC
7
50
VCC
VCC
7
50
VCC
1Q4
8
49
1D4
1Q4
8
49
1D4
1Q5
9
48
1D5
1Q5
9
48
1D5
1Q6
10
47
1D6
1Q6
10
47
1D6
GND
11
46
GND
GND
11
46
GND
1Q7
12
45
1D7
1Q7
12
45
1D7
1Q8
13
44
1D8
1Q8
13
44
1D8
1Q9
14
1D9
1Q9
14
43
1D9
2Q1
15
SO56-1 43
SO56-2
SO56-3 42
2D1
2Q1
15
42
2D1
2Q2
16
41
2D2
2Q2
16
41
2D2
2Q3
17
40
2D3
2Q3
17
40
2D3
GND
18
39
GND
GND
18
39
GND
2Q4
19
38
2D4
2Q4
19
38
2D4
2Q5
20
37
2D5
2Q5
20
37
2D5
2Q6
21
36
2D6
2Q6
21
36
2D6
VCC
22
35
VCC
VCC
22
35
VCC
2Q7
23
34
2D7
2Q7
23
34
2D7
2Q8
24
33
2D8
2Q8
24
33
2D8
GND
25
32
GND
GND
25
32
GND
2Q9
26
31
2D9
2Q9
26
31
2D9
2OE
27
30
2CLKEN
2OE
27
30
2CLKEN
2CLR
28
29
2CLK
2CLR
28
29
2CLK
1CLR
1
56
1CLK
1OE
2
55
1Q1
3
GND
SSOP/
TSSOP/TVSOP
TOP VIEW
E56-1
CERPACK
TOP VIEW
2772 drw 03
2772 drw 04
5.16
2
IDT54/74FCT16823AT/BT/CT/ET, 162823AT/BT/CT/ET
FAST CMOS 18-BIT REGISTER
MILITARY AND COMMERCIAL TEMPERATURE RANGES
FUNCTION TABLE(1)
PIN DESCRIPTION
Data inputs
xOE
xCLR
Inputs
xCLKEN
xCLK
xDx
Clock Inputs
H
X
X
X
X
Clock Enable Inputs (Active LOW)
L
L
X
X
H
H
X
H
H
L
xOE
Asynchronous clear Inputs
(Active LOW)
Output Enable Inputs (Active LOW)
L
H
H
xQx
3-State Outputs
L
H
L
H
Pin Names
xDx
xCLK
xCLKEN
xCLR
Description
2772 tbl 01
(1)
Unit
V
I OUT
mA
DC Output Current
–60 to +120
Z
High Z
X
L
Clear
X
Q(2)
Hold
↑
L
Z
Load
L
↑
H
Z
L
↑
L
L
L
↑
H
H
NOTES:
2772 tbl 02
1. H = HIGH Voltage Level
L = LOW Voltage Level
X = Don’t Care
Z = High Impedance
2. Output level before indicated steady-state input conditions were established.
ABSOLUTE MAXIMUM RATINGS
Symbol
Description
Max.
VTERM(2) Terminal Voltage with Respect to –0.5 to +7.0
GND
VTERM(3) Terminal Voltage with Respect to
–0.5 to
GND
VCC +0.5
TSTG
Storage Temperature
–65 to +150
Outputs
xQx Function
V
°C
CAPACITANCE (TA = +25°C, f = 1.0MHz)
2772 lnk 03
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating
only and functional operation of the device at these or any other conditions
above those indicated in the operational sections of this specification is
not implied. Exposure to absolute maximum rating conditions for
extended periods may affect reliability.
2. All device terminals except FCT162XXXT Output and I/O terminals.
3. Output and I/O terminals for FCT162XXXT.
Symbol
Parameter(1)
CIN
Input
Capacitance
COUT
Output
Capacitance
Conditions
VIN = 0V
Typ.
3.5
VOUT = 0V
3.5
Max. Unit
6.0
pF
8.0
pF
2772 lnk 04
NOTE:
1. This parameter is measured at characterization but not tested.
5.16
3
IDT54/74FCT16823AT/BT/CT/ET, 162823AT/BT/CT/ET
FAST CMOS 18-BIT REGISTER
MILITARY AND COMMERCIAL TEMPERATURE RANGES
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Commercial: TA = –40°C to +85°C, VCC = 5.0V ± 10%; Military: TA = –55°C to +125°C, V CC = 5.0V ± 10%
Parameter
Input HIGH Level
Test Conditions(1)
Guaranteed Logic HIGH Level
VIL
Input LOW Level
II H
Input HIGH Current (Input pins)(5)
Symbol
VIH
Min.
2.0
Typ.(2)
—
Max.
Guaranteed Logic LOW Level
—
—
0.8
V
VCC = Max.
—
—
±1
µA
—
—
±1
—
—
±1
—
—
±1
—
—
±1
VI = VCC
Input HIGH Current (I/O pins)(5)
II L
Input LOW Current (Input
pins)(5)
VI = GND
Input LOW Current (I/O pins)(5)
I OZH
High Impedance Output Current
VCC = Max.
VO = 2.7V
pins) (5)
I OZL
(3-State Output
VIK
Clamp Diode Voltage
I OS
Short Circuit Current
VH
Input Hysteresis
I CCL
I CCH
I CCZ
Quiescent Power Supply Current
VO = 0.5V
VCC = Min., IIN = –18mA
VCC = Max., VO =
GND (3)
—
VCC = Max., VIN = GND or VCC
—
Unit
V
µA
—
—
±1
—
–0.7
–1.2
V
–80
–140
–225
mA
—
100
—
mV
—
5
500
µA
2772 lnk 05
OUTPUT DRIVE CHARACTERISTICS FOR FCT16823T
Symbol
IO
Parameter
Output Drive Current
Test Conditions(1)
VCC = Max., VO = 2.5V(3)
Min.
–50
Typ.(2)
Max.
—
–180
Unit
mA
VOH
Output HIGH Voltage
VCC = Min.
2.5
3.5
—
V
2.4
3.5
—
V
2.0
3.0
—
V
—
0.2
0.55
V
—
—
±1
µA
I OH = –3mA
VIN = VIH or V IL
VOL
Output LOW Voltage
I OFF
Input/Output Power Off Leakage(5)
VCC = Min.
VIN = VIH or V IL
VCC = 0V, VIN or V O
I OH = –12mA MIL.
I OH = –15mA COM'L.
I OH = –24mA MIL.
I OH = –32mA COM'L.(4)
I OL = 48mA MIL.
I OL = 64mA COM'L.
≤ 4.5V
2772 lnk 06
OUTPUT DRIVE CHARACTERISTICS FOR FCT162823T
Symbol
I ODL
Parameter
Output LOW Current
Test Conditions(1)
VCC = 5V, VIN = VIH or VIL, VOUT = 1.5V (3)
Min.
60
Typ.(2)
115
Max.
200
Unit
mA
I ODH
Output HIGH Current
VCC = 5V, VIN = VIH or VIL, VOUT = 1.5V(3)
–60
–115
–200
mA
VOH
Output HIGH Voltage
2.4
3.3
—
V
VOL
Output LOW Voltage
VCC = Min.
VIN = VIH or V IL
VCC = Min.
VIN = VIH or V IL
—
0.3
0.55
V
I OH = –16mA MIL.
I OH = –24mA COM'L.
I OL = 16mA MIL.
I OL = 24mA COM'L.
NOTES:
1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at Vcc = 5.0V, +25°C ambient.
3. Not more than one output should be tested at one time. Duration of the test should not exceed one second.
4. Duration of the condition can not exceed one second.
5. The test limit for this parameter is ± 5µA at TA = –55°C.
5.16
2772 lnk 07
4
IDT54/74FCT16823AT/BT/CT/ET, 162823AT/BT/CT/ET
FAST CMOS 18-BIT REGISTER
MILITARY AND COMMERCIAL TEMPERATURE RANGES
POWER SUPPLY CHARACTERISTICS
Test Conditions(1)
Min.
—
Typ.(2)
0.5
Max.
1.5
Unit
mA
VIN = VCC
VIN = GND
—
75
120
µA/
MHz
VCC = Max.
Outputs Open
fCP= 10MHz
50% Duty Cycle
VIN = VCC
VIN = GND
—
0.8
1.7
mA
xOE = xCLKEN = GND
at fi = 5MHz
50% Duty Cycle
One Bit Toggling
VIN = 3.4V
VIN = GND
—
1.3
3.2
VCC = Max.
Outputs Open
fCP= 10MHz
50% Duty Cycle
VIN = VCC
VIN = GND
—
4.2
7.1 (5)
xOE = xCLKEN = GND
at fi = 2.5MHz
50% Duty Cycle
Eighteen Bits Toggling
VIN = 3.4V
VIN = GND
—
9.2
22.1 (5)
Symbol
∆ICC
Parameter
Quiescent Power Supply Current
TTL Inputs HIGH
ICCD
Dynamic Power Supply Current (4)
VCC = Max.
Outputs Open
xOE = xCLKEN = GND
One Input Toggling
50% Duty Cycle
IC
Total Power Supply Current (6)
VCC = Max.
VIN = 3.4V(3)
NOTES:
1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at VCC = 5.0V, +25°C ambient.
3. Per TTL driven input (VIN = 3.4V). All other inputs at VCC or GND.
4. This parameter is not directly testable, but is derived for use in Total Power Supply Calculations.
5. Values for these conditions are examples of the ICC formula. These limits are guaranteed but not tested.
6. IC = IQUIESCENT + IINPUTS + IDYNAMIC
IC = ICC + ∆ICC DHNT + ICCD (fCPNCP/2 + fiNi)
ICC = Quiescent Current (ICCL, ICCH and ICCZ)
∆ICC = Power Supply Current for a TTL High Input (VIN = 3.4V)
DH = Duty Cycle for TTL Inputs High
NT = Number of TTL Inputs at DH
ICCD = Dynamic Current Caused by an Input Transition Pair (HLH or LHL)
fCP = Clock Frequency for Register Devices (Zero for Non-Register Devices)
NCP = Number of Clock Inputs at fCP
fi = Input Frequency
Ni = Number of Inputs at fi
5.16
2772 tbl 08
5
IDT54/74FCT16823AT/BT/CT/ET, 162823AT/BT/CT/ET
FAST CMOS 18-BIT REGISTER
MILITARY AND COMMERCIAL TEMPERATURE RANGES
SWITCHING CHARACTERISTICS OVER OPERATING RANGE
FCT16823AT/162823AT
Com'l.
Symbol
tPLH
tPHL
tPHL
tPZH
tPZL
tPHZ
tPLZ
tSU
Parameter
Propagation Delay
xCLK to xQx
Propagation Delay
xCLR to xQx
Output Enable Time
xOE to xQx
Output Disable Time
xOE to xQx
tW
Set-up Time HIGH or LOW
xDx to xCLK
Hold Time HIGH or LOW
xDx to xCLK
Set-up Time HIGH or LOW
xCLKEN to xCLK
Hold Time HIGH or LOW
xCLKEN to xCLK
xCLK Pulse Width
HIGH or LOW
xCLR Pulse Width LOW
tREM
Recovery Time xCLR to xCLK
tH
tSU
tH
tW
tSK(o) Output
Skew (3)
FCT16823BT/162823BT
Mil.
Com'l.
Mil.
Condition(1)
Min.(2)
Max.
Min.(2)
Max.
Min.(2)
Max.
Min.(2)
Max.
Unit
CL = 50pF
RL = 500Ω
CL = 300pF(5)
RL = 500Ω
CL = 50pF
RL = 500Ω
CL = 50pF
RL = 500Ω
CL = 300pF(5)
RL = 500Ω
CL = 5pF(5)
RL = 500Ω
CL = 50pF
RL = 500Ω
CL = 50pF
RL = 500Ω
1.5
10.0
1.5
11.5
1.5
7.5
1.5
8.5
ns
1.5
20.0
1.5
20.0
1.5
15.0
1.5
16.0
1.5
14.0
1.5
15.0
1.5
9.0
1.5
9.5
ns
1.5
12.0
1.5
13.0
1.5
8.0
1.5
9.0
ns
1.5
23.0
1.5
25.0
1.5
15.0
1.5
16.0
1.5
7.0
1.5
8.0
1.5
6.5
1.5
7.0
1.5
8.0
1.5
9.0
1.5
7.5
1.5
8.0
4.0
—
4.0
—
3.0
—
3.0
—
ns
2.0
—
2.0
—
1.5
—
1.5
—
ns
4.0
—
4.0
—
3.0
—
3.0
—
ns
2.0
—
2.0
—
0
—
0
—
ns
7.0
—
7.0
—
6.0
—
6.0
—
ns
6.0
—
7.0
—
6.0
—
6.0
—
ns
6.0
—
7.0
—
6.0
—
6.0
—
ns
—
0.5
—
0.5
—
0.5
—
0.5
ns
NOTES:
1. See test circuit and waveforms.
2. Minimum limits are guaranteed but not tested on Propagation Delays.
3. Skew between any two outputs of the same package switching in the same direction. This parameter is guaranteed by design.
4. This limit is guaranteed but not tested.
5. This condition is guaranteed but not tested.
5.16
ns
2772 tbl 09
6
IDT54/74FCT16823AT/BT/CT/ET, 162823AT/BT/CT/ET
FAST CMOS 18-BIT REGISTER
MILITARY AND COMMERCIAL TEMPERATURE RANGES
SWITCHING CHARACTERISTICS OVER OPERATING RANGE
FCT16823CT/162823CT
Com'l.
Symbol
tPLH
tPHL
tPHL
tPZH
tPZL
tPHZ
tPLZ
tSU
Parameter
Propagation Delay
xCLK to xQx
Propagation Delay
xCLR to xQx
Output Enable Time
xOE to xQx
Output Disable Time
xOE to xQx
tW
Set-up Time HIGH or LOW
xDx to xCLK
Hold Time HIGH or LOW
xDx to xCLK
Set-up Time HIGH or LOW
xCLKEN to xCLK
Hold Time HIGH or LOW
xCLKEN to xCLK
xCLK Pulse Width
HIGH or LOW
xCLR Pulse Width LOW
tREM
Recovery Time xCLR to xCLK
tH
tSU
tH
tW
tSK(o) Output Skew (3)
Condition(1)
Min.(2)
CL = 50pF
RL = 500Ω
CL = 300pF(5)
RL = 500Ω
CL = 50pF
RL = 500Ω
CL = 50pF
RL = 500Ω
CL = 300pF(5)
RL = 500Ω
CL = 5pF(5)
RL = 500Ω
CL = 50pF
RL = 500Ω
CL = 50pF
RL = 500Ω
1.5
FCT16823ET/162823ET
Mil.
Max.
Min.(2)
6.0
1.5
1.5
12.5
1.5
Com'l.
Max.
Min.(2)
7.0
1.5
1.5
13.5
8.0
1.5
1.5
7.0
1.5
Mil.
Max.
Min.(2)
Max.
Unit
4.4
—
—
ns
1.5
8.0
—
—
8.5
1.5
4.4
—
—
ns
1.5
8.0
1.5
4.4
—
—
ns
12.5
1.5
13.5
1.5
9.0
—
—
1.5
6.2
1.5
6.2
1.5
3.6
—
—
1.5
6.5
1.5
6.5
1.5
3.6
—
—
3.0
—
3.0
—
1.5
—
—
—
ns
1.5
—
1.5
—
0.0
—
—
—
ns
3.0
—
3.0
—
2.5
—
—
—
ns
0
—
0
—
0.0
—
—
—
ns
6.0
—
6.0
—
3.0 (4)
—
—
—
ns
6.0
—
6.0
—
3.0 (4)
—
—
—
ns
6.0
—
6.0
—
3.0
—
—
—
ns
—
0.5
—
0.5
—
0.5
—
—
ns
NOTES:
1. See test circuit and waveforms.
2. Minimum limits are guaranteed but not tested on Propagation Delays.
3. Skew between any two outputs of the same package switching in the same direction. This parameter is guaranteed by design.
4. This limit is guaranteed but not tested.
5. This condition is guaranteed but not tested.
5.16
ns
2772 tbl 10
7
IDT54/74FCT16823AT/BT/CT/ET, 162823AT/BT/CT/ET
FAST CMOS 18-BIT REGISTER
MILITARY AND COMMERCIAL TEMPERATURE RANGES
TEST CIRCUITS AND WAVEFORMS
SWITCH POSITION
TEST CIRCUITS FOR ALL OUTPUTS
V CC
7.0V
500Ω
VIN
Open Drain
Disable Low
Closed
Open
All Other Tests
D.U.T.
50pF
RT
Switch
Enable Low
V OUT
Pulse
Generator
Test
2772 lnk 10
DEFINITIONS:
CL= Load capacitance: includes jig and probe capacitance.
RT = Termination resistance: should be equal to ZOUT of the Pulse
Generator.
500Ω
CL
2772 drw 05
SET-UP, HOLD AND RELEASE TIMES
DATA
INPUT
TIMING
INPUT
ASYNCHRONOUS CONTROL
PRESET
CLEAR
ETC.
SYNCHRONOUS CONTROL
PRESET
CLEAR
CLOCK ENABLE
ETC.
tH
tSU
tREM
tSU
PULSE WIDTH
3V
1.5V
0V
3V
1.5V
0V
LOW-HIGH-LOW
PULSE
1.5V
tW
3V
1.5V
0V
HIGH-LOW-HIGH
PULSE
1.5V
2772 drw 07
3V
1.5V
0V
tH
2772 drw 06
PROPAGATION DELAY
ENABLE AND DISABLE TIMES
ENABLE
SAME PHASE
INPUT TRANSITION
tPLH
tPHL
OUTPUT
tPLH
OPPOSITE PHASE
INPUT TRANSITION
tPHL
3V
1.5V
0V
DISABLE
3V
1.5V
CONTROL
INPUT
tPZL
VOH
1.5V
VOL
OUTPUT
NORMALLY
LOW
3V
1.5V
0V
SWITCH
CLOSED
3.5V
1.5V
tPZH
OUTPUT
NORMALLY
HIGH
2772 drw 08
SWITCH
OPEN
0V
tPLZ
3.5V
0.3V
VOL
tPHZ
0.3V
1.5V
0V
VOH
0V
2772 drw 09
NOTES:
1. Diagram shown for input Control Enable-LOW and input Control
Disable-HIGH
2. Pulse Generator for All Pulses: Rate ≤ 1.0MHz; tF ≤ 2.5ns; tR ≤ 2.5ns
5.16
8
IDT54/74FCT16823AT/BT/CT/ET, 162823AT/BT/CT/ET
FAST CMOS 18-BIT REGISTER
MILITARY AND COMMERCIAL TEMPERATURE RANGES
ORDERING INFORMATION
IDT
FCT
XX
XXXX
Temp. Range
Device Type
X
Package
X
Process
Blank
B
Commercial
MIL-STD-883, Class B
PV
PA
PF
E
Shrink Small Outline Package (SO56-1)
Thin Shrink Small Outline Package (SO56-2)
Thin Very Small Outline Package (SO56-3)
CERPACK (E56-1)
16823AT Non-Inverting 18-Bit Register
16823BT
16823CT
16823ET
162823AT
162823BT
162823CT
162823ET
54
74
–55°C to +125°C
–40°C to +85°C
2772 drw 10
5.16
9
Similar pages