TI1 DS08MB200TSQX/NOPB Dual 800 mbps 2:1/1:2 lvds mux/buffer Datasheet

DS08MB200
www.ti.com
SNLS197D – MAY 2006 – REVISED MARCH 2013
DS08MB200 Dual 800 Mbps 2:1/1:2 LVDS Mux/Buffer
Check for Samples: DS08MB200
FEATURES
DESCRIPTION
•
•
The DS08MB200 is a dual-port 1 to 2 repeater/buffer
and 2 to 1 multiplexer. High-speed data paths and
flow-through pinout minimize internal device jitter and
simplify board layout. The differential inputs and
outputs interface to LVDS or Bus LVDS signals such
as those on TI's 10-, 16-, and 18- bit Bus LVDS
SerDes, or to CML or LVPECL signals.
1
2
•
•
•
•
•
•
•
Up to 800 Mbps Data Rate per Channel
LVDS/BLVDS/CML/LVPECL Compatible Inputs,
LVDS Compatible Outputs
Low Output Skew and Jitter
On-Chip 100Ω Input Termination
15 kV ESD Protection on LVDS Inputs/Outputs
Hot Plug Protection
Single 3.3V Supply
Industrial -40 to +85°C Temperature Range
48-pin WQFN Package
The 3.3V supply, CMOS process, and robust I/O
ensure high performance at low power over the entire
industrial -40 to +85°C temperature range.
Switch
Fabric B
LVDS
Backplane or Cable
Switch
Fabric A
LVDS
Typical Application
Mux Buffer
FPGA
or
ASIC
Block Diagram
ENA_0
ENB_0
SOA_0
LI_0
SOB_0
ENL_0
SIA_0
LO_0
SIB_0
MUX_S0
Channel 0
Channel 1
Figure 1. DS08MB200 Block Diagram
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2006–2013, Texas Instruments Incorporated
DS08MB200
SNLS197D – MAY 2006 – REVISED MARCH 2013
www.ti.com
PIN DESCRIPTIONS
Pin
Name
WQFN Pin
Number
I/O, Type
Description
SWITCH SIDE DIFFERENTIAL INPUTS
SIA_0+
SIA_0−
30
29
I, LVDS
Switch A-side Channel 0 inverting and non-inverting differential inputs. LVDS, Bus LVDS, CML, or
LVPECL compatible.
SIA_1+
SIA_1−
19
20
I, LVDS
Switch A-side Channel 1 inverting and non-inverting differential inputs. LVDS, Bus LVDS, CML, or
LVPECL compatible.
SIB_0+
SIB_0−
28
27
I, LVDS
Switch B-side Channel 0 inverting and non-inverting differential inputs. LVDS, Bus LVDS, CML, or
LVPECL compatible.
SIB_1+
SIB_1−
21
22
I, LVDS
Switch B-side Channel 1 inverting and non-inverting differential inputs. LVDS, Bus LVDS, CML, or
LVPECL compatible.
LINE SIDE DIFFERENTIAL INPUTS
LI_0+
LI_0−
40
39
I, LVDS
Line-side Channel 0 inverting and non-inverting differential inputs. LVDS, Bus LVDS, CML, or
LVPECL compatible.
LI_1+
LI_1−
9
10
I, LVDS
Line-side Channel 1 inverting and non-inverting differential inputs. LVDS, Bus LVDS, CML, or
LVPECL compatible.
SWITCH SIDE DIFFERENTIAL OUTPUTS
SOA_0+
SOA_0−
34
33
O, LVDS
Switch A-side Channel 0 inverting and non-inverting differential outputs. LVDS compatible (1) (2).
SOA_1+
SOA_1−
15
16
O, LVDS
Switch A-side Channel 1 inverting and non-inverting differential outputs. LVDS compatible (1) (2).
SOB_0+
SOB_0−
32
31
O, LVDS
Switch B-side Channel 0 inverting and non-inverting differential outputs. LVDS compatible (1) (2).
SOB_1+
SOB_1−
17
18
O, LVDS
Switch B-side Channel 1 inverting and non-inverting differential outputs. LVDS compatible (1) (2).
LINE SIDE DIFFERENTIAL OUTPUTS
LO_0+
LO_0−
42
41
O, LVDS
Line-side Channel 0 inverting and non-inverting differential outputs. LVDS compatible (1) (2).
LO_1+
LO_1−
7
8
O, LVDS
Line-side Channel 1 inverting and non-inverting differential outputs. LVDS compatible (1) (2).
DIGITAL CONTROL INTERFACE
MUX_S0
MUX_S1
38
11
I, LVTTL
Mux Select Control Inputs (per channel) to select which Switch-side input, A or B, is passed through
to the Line-side.
ENA_0
ENA_1
ENB_0
ENB_1
36
13
35
14
I, LVTTL
Output Enable Control for Switch A-side and B-side outputs. Each output driver on the A-side and Bside has a separate enable pin.
ENL_0
ENL_1
45
4
I, LVTTL
Output Enable Control for The Line-side outputs. Each output driver on the Line-side has a separate
enable pin.
VDD
6, 12, 37,
43, 48
I, Power
VDD = 3.3V ±0.3V.
GND
2, 3, 46,
47 (3)
I, Power
Ground reference for LVDS and CMOS circuitry.
For the WQFN package, the DAP is used as the primary GND connection to the device. The DAP is
the exposed metal contact at the bottom of the WQFN-48 package. It should be connected to the
ground plane with at least 4 vias for optimal AC and thermal performance.
N/C
1, 5, 23, 24,
25, 26, 44
POWER
(1)
(2)
(3)
2
No Connect
For interfacing LVDS outputs to CML or LVPECL compatible inputs, refer to the APPLICATIONS section of this datasheet.
The LVDS outputs do not support a multidrop (BLVDS) environment. The LVDS output characteristics of the DS08MB200 device have
been optimized for point-to-point backplane and cable applications.
Note that the DAP on the backside of the WQFN package is the primary GND connection for the device when using the WQFN
package.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: DS08MB200
DS08MB200
www.ti.com
SNLS197D – MAY 2006 – REVISED MARCH 2013
Connection Diagrams
N/C
GND
GND
1
48
ENL_1
2
N/C
3
VDD
4
LO-1+
N/C
5
LO_1-
GND
6
LI_1+
GND
7
LI_1-
ENL_1
8
MUX_S1
N/C
9
VDD
VDD
ENB_1
LO-1+
12 11 10
13
LO_1-
ENA_1
Top View
LI_1+
LI_1-
MUX_S1
VDD
Top View
47
GND
ENB_1
SOA_1+
15
46
GND
SOA_1+
GND
SOA_1-
16
45
ENL_0
SOA_1-
ENL_0
SOB_1+
17
44
N/C
SOB_1+
SOB_1-
18
43
VDD
SOB_1-
VDD
SIA_1+
19
42
LO_0+
SIA_1+
LO_0+
SIA_1-
20
41
LO_0-
SIA_1-
LO_0-
SIB_1+
21
40
LI_0+
SIB_1+
LI_0+
SIB_1-
22
39
LI_0-
SIB_1-
LI_0-
N/C
23
38
MUX_S0
N/C
MUX_S0
N/C
37
24
25 26 27 28 29 30 31 32 33 34 35 36
VDD
N/C
VDD
Figure 2. WQFN Package
See Package Number RHS0048A
DAP = GND
VDD
Channel 1
GND
N/C
ENA_0
ENB_0
SOA_0+
SOA_0-
SOB_0+
SOB_0-
SIA_0+
SIA_0-
SIB_0+
SIB_0-
N/C
Channel 0
N/C
ENB_0
SOA_0+
SOA_0-
SOB_0+
SOB_0-
SIA_0+
SIA_0-
SIB_0+
SIB_0-
N/C
DAP
(GND)
ENA_0
ENA_1
14
N/C
VDD
Figure 3. Directional Signal Paths
(Refer to pin names for signal polarity)
TRI-STATE and Powerdown Modes
The DS08MB200 has output enable control on each of the six onboard LVDS output drivers. This control allows
each output individually to be placed in a low power TRI-STATE mode while the device remains active, and is
useful to reduce power consumption on unused channels. In TRI-STATE mode, some outputs may remain active
while some are in TRI-STATE.
When all six of the output enables (all drivers on both channels) are deasserted (LOW), then the device enters a
Powerdown mode that consumes only 0.5mA (typical) of supply current. In this mode, the entire device is
essentially powered off, including all receiver inputs, output drivers and internal bandgap reference generators.
When returning to active mode from Powerdown mode, there is a delay until valid data is presented at the
outputs because of the ramp to power up the internal bandgap reference generators.
Any single output enable that remains active will hold the device in active mode even if the other five outputs are
in TRI-STATE.
When in Powerdown mode, any output enable that becomes active will wake up the device back into active
mode, even if the other five outputs are in TRI-STATE.
Input Failsafe Biasing
External pull up and pull down resistors may be used to provide enough of an offset to enable an input failsafe
under open-circuit conditions. This configuration ties the positive LVDS input pin to VDD thru a pull up resistor
and the negative LVDS input pin is tied to GND by a pull down resistor. The pull up and pull down resistors
should be in the 5kΩ to 15kΩ range to minimize loading and waveform distortion to the driver. Please refer to
application note SNLA051B AN-1194, “Failsafe Biasing of LVDS Interfaces” for more information.
Output Characteristics
The output characteristics of the DS08MB200 have been optimized for point-to-point backplane and cable
applications, and are not intended for multipoint or multidrop signaling.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: DS08MB200
3
DS08MB200
SNLS197D – MAY 2006 – REVISED MARCH 2013
www.ti.com
MULTIPLEXER TRUTH TABLE (1) (2)
Data Inputs
(3)
Output
SIB_0
MUX_S0
ENL_0
LO_0
X
valid
0
1
SIB_0
valid
X
1
1
SIA_0
X
(1)
(2)
Control Inputs
SIA_0
X
X
0
(3)
Z
Same functionality for channel 1
X = Don't Care
Z = High Impedance (TRI-STATE)
When all enable inputs from both channels are Low, the device enters a powerdown mode. Refer to the TRI-STATE and Powerdown
Modes section.
REPEATER/BUFFER TRUTH TABLE (1) (2)
Data Input
LI_0
(1)
(2)
(3)
Control Inputs
ENA_0
Outputs
ENB_0
SOA_0
Z
(3)
SOB_0
Z
(3)
X
0
0
valid
0
1
Z
valid
1
0
LI_0
Z
valid
1
1
LI_0
LI_0
LI_0
Same functionality for channel 1
X = Don't Care
Z = High Impedance (TRI-STATE)
When all enable inputs from both channels are Low, the device enters a powerdown mode. Refer to the TRI-STATE and Powerdown
Modes section.
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ABSOLUTE MAXIMUM RATINGS (1)
Supply Voltage (VDD)
−0.3V to +4.0V
CMOS Input Voltage
-0.3V to (VDD+0.3V)
LVDS Receiver Input Voltage (2)
-0.3V to (VDD+0.3V)
LVDS Driver Output Voltage
-0.3V to (VDD+0.3V)
LVDS Output Short Circuit Current
+40 mA
Junction Temperature
+150°C
Storage Temperature
−65°C to +150°C
Lead Temperature (Solder, 4sec)
260°C
Max Pkg Power Capacity @ 25°C
5.2W
Thermal Resistance (θJA)
24°C/W
Package Derating above +25°C
ESD Last Passing Voltage
41.7mW/°C
HBM, 1.5kΩ, 100pF
15kV
EIAJ, 0Ω, 200pF
250V
CDM
(1)
(2)
8kV
LVDS pins to GND only
1000V
Absolute maximum ratings are those values beyond which damage to the device may occur. Texas Instruments does not recommend
operation of products outside of recommended operation conditions.
VID max < 2.4V
RECOMMENDED OPERATING CONDITIONS
Supply Voltage (VCC)
Input Voltage (VI)
3.0V to 3.6V
(1)
0V to VCC
Output Voltage (VO)
Operating Temperature (TA)
(1)
4
0V to VCC
Industrial
−40°C to +85°C
VID max < 2.4V
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: DS08MB200
DS08MB200
www.ti.com
SNLS197D – MAY 2006 – REVISED MARCH 2013
ELECTRICAL CHARACTERISTICS
Over recommended operating supply and temperature ranges unless other specified.
Symbol
Parameter
Conditions
Min
Typ (1)
Max
Units
V
LVTTL DC SPECIFICATIONS (MUX_Sn, ENA_n, ENB_n, ENL_n)
VIH
High Level Input Voltage
2.0
VDD
VIL
Low Level Input Voltage
GND
0.8
V
IIH
High Level Input Current
VIN = VDD = VDDMAX
−10
+10
µA
IIL
Low Level Input Current
VIN = VSS, VDD = VDDMAX
−10
+10
µA
CIN1
Input Capacitance
Any Digital Input Pin to VSS
3.5
pF
COUT1
Output Capacitance
Any Digital Output Pin to VSS
5.5
pF
VCL
Input Clamp Voltage
ICL = −18 mA
−0.8
V
−1.5
LVDS INPUT DC SPECIFICATIONS (SIA±, SIB±, LI±)
VTH
Differential Input High Threshold (2)
VCM = 0.8V or 1.2V or 3.55V,
VDD = 3.6V
VTL
Differential Input Low Threshold (2)
VCM = 0.8V or 1.2V or 3.55V,
VDD = 3.6V
−100
VID
Differential Input Voltage
VCM = 0.8V to 3.55V, VDD = 3.6V
100
VCMR
Common Mode Voltage Range
VID = 150 mV, VDD = 3.6V
0.05
CIN2
Input Capacitance
IN+ or IN− to VSS
IIN
Input Current
VIN = 3.6V, VDD = VDDMAX
−15
+15
µA
VIN = 0V, VDD = VDDMAX
−15
+15
µA
500
mV
35
mV
1.475
V
35
mV
-40
mA
0
100
0
mV
mV
2400
3.55
3.5
mV
V
pF
LVDS OUTPUT DC SPECIFICATIONS (SOA_n±, SOB_n±, LO_n±)
VOD
Differential Output Voltage (2)
ΔVOD
Change in VOD between
Complementary States
RL is the internal 100Ω between OUT+
and OUT−
250
360
-35
(3)
VOS
Offset Voltage
ΔVOS
Change in VOS between
Complementary States
1.05
1.22
IOS
Output Short Circuit Current
OUT+ or OUT− Short to GND
−21
COUT2
Output Capacitance
OUT+ or OUT− to GND when TRISTATE
5.5
All inputs and outputs enabled and
active, terminated with differential load of
100Ω between OUT+ and OUT-.
225
275
mA
ENA_0 = ENB_0 = ENL_0= ENA_1 =
ENB_1 = ENL_1 = L
0.6
4.0
mA
170
250
ps
170
250
ps
1.0
2.5
ns
1.0
2.5
ns
-35
pF
SUPPLY CURRENT (Static)
ICC
Supply Current
ICCZ
Supply Current - Powerdown Mode
SWITCHING CHARACTERISTICS—LVDS OUTPUTS
tLHT
Differential Low to High Transition
Time
tHLT
Differential High to Low Transition
Time
tPLHD
Differential Low to High Propagation
Delay
tPHLD
Differential High to Low Propagation
Delay
tSKD1
Pulse Skew
|tPLHD–tPHLD| (4)
25
75
ps
tSKCC
Output Channel to Channel Skew
Difference in propagation delay (tPLHD or
tPHLD) among all output channels. (4)
50
115
ps
(1)
(2)
(3)
(4)
Use an alternating 1 and 0 pattern at 200
Mb/s, measure between 20% and 80% of
VOD. (4)
Use an alternating 1 and 0 pattern at 200
Mb/s, measure at 50% VOD between
input to output.
Typical parameters are measured at VDD = 3.3V, TA = 25°C. They are for reference purposes, and are not production-tested.
Differential output voltage VOD is defined as ABS(OUT+–OUT−). Differential input voltage VID is defined as ABS(IN+–IN−).
Output offset voltage VOS is defined as the average of the LVDS single-ended output voltages at logic high and logic low states.
Not production tested. Ensured by statistical analysis on a sample basis at the time of characterization.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: DS08MB200
5
DS08MB200
SNLS197D – MAY 2006 – REVISED MARCH 2013
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
Over recommended operating supply and temperature ranges unless other specified.
Symbol
tJIT
Parameter
Jitter
(5)
Conditions
RJ - Alternating 1 and 0 at 400 MHz
Min
(6)
Typ (1)
Max
Units
1.3
1.5
psrms
DJ - K28.5 Pattern, 800 Mbps (7)
15
34
psp-p
TJ - PRBS 27-1 Pattern, 800 Mbps (8)
16
34
psp-p
tON
LVDS Output Enable Time
Time from ENA_n, ENB_n, or ENL_n to
OUT± change from TRI-STATE to active.
0.5
1.5
µs
tON2
LVDS Output Enable time from
powerdown mode
Time from ENA_n, ENB_n, or ENL_n to
OUT± change from Powerdown to active
10
20
µs
tOFF
LVDS Output Disable Time
Time from ENA_n, ENB_n, or ENL_n to
OUT± change from active to TRI-STATE
or powerdown.
12
ns
(5)
(6)
(7)
(8)
6
Jitter is not production tested, but ensured through characterization on a sample basis.
Random Jitter, or RJ, is measured RMS with a histogram including 1500 histogram window hits. The input voltage = VID = 500mV, 50%
duty cycle at 400 MHz, tr = tf = 50ps (20% to 80%).
Deterministic Jitter, or DJ, is measured to a histogram mean with a sample size of 350 hits. Stimulus and fixture jitter has been
subtracted. The input voltage = VID = 500mV, K28.5 pattern at 800 Mbps, tr = tf = 50ps (20% to 80%). The K28.5 pattern is repeating bit
streams of (0011111010 1100000101).
Total Jitter, or TJ, is measured peak to peak with a histogram including 3500 window hits. Stimulus and fixture jitter has been subtracted.
The input voltage = VID = 500mV, 27-1 PRBS pattern at 800 Mbps, tr = tf = 50ps (20% to 80%).
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: DS08MB200
DS08MB200
www.ti.com
SNLS197D – MAY 2006 – REVISED MARCH 2013
TYPICAL PERFORMANCE CHARACTERISTICS
Power Supply Current vs. Bit Data Rate
Total Jitter vs. Temperature
POWER SUPPLY CURRENT (mA)
350
300
250
200
150
100
50
0
0
200
400
600
800
BIT DATA RATE (Mbps)
7-1
Dynamic power supply current was measured with all channels active Total Jitter measured at 0V differential while running a PRBS 2
pattern
with
one
channel
active,
all
other
channels
are
disabled.
VDD =
and toggling at the bit data rate. Data pattern has no effect on the
power consumption. VDD = 3.3V, TA = +25°C, VID = 0.5V, VCM = 1.2V. 3.3V, VID = 0.5V, VCM = 1.2V, 800 Mbps data rate. Stimulus and
fixture jitter has been subtracted.
Figure 4.
Figure 5.
Total Jitter vs. Bit Data Rate
Total Jitter measured at 0V differential while running a PRBS 27-1 pattern with one channel active, all other channels are disabled.
VDD = 3.3V, TA = +25°C, VID = 0.5V. Stimulus and fixture jitter has been subtracted.
Figure 6.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: DS08MB200
7
DS08MB200
SNLS197D – MAY 2006 – REVISED MARCH 2013
www.ti.com
APPLICATIONS
Interfacing LVPECL to LVDS
An LVPECL driver consists of a differential pair with coupled emitters connected to GND via a current source.
This drives a pair of emitter-followers that require a 50 ohm to VCC-2.0 load. A modern LVPECL driver will
typically include the termination scheme within the device for the emitter follower. If the driver does not include
the load, then an external scheme must be used. The 1.3 V supply is usually not readily available on a PCB,
therefore, a load scheme without a unique power supply requirement may be used.
50:
15MB200
LVPECL
50:
R1
150:
R2
150:
Figure 7. DC Coupled LVPECL to LVDS Interface
Figure 7 is a separated π termination scheme for a 3.3 V LVPECL driver. R1 and R2 provides proper DC load for
the driver emitter followers, and may be included as part of the driver device. The DS08MB200 includes a 100
ohm input termination for the transmission line. The common mode voltage will be at the normal LVPECL
levels – around 2 V. This scheme works well with LVDS receivers that have rail-to-rail common mode voltage,
VCM, range. Most Texas Instruments LVDS receivers have wide VCM range. The exceptions are noted in devices’
respective datasheets. Those LVDS devices that do have a wide VCM range do not vary in performance
significantly when receiving a signal with a common mode other than standard LVDS VCM of 1.2 V.
0.1 PF
50:
15MB200
LVPECL
50:
R1
150:
R2
150:
0.1 PF
Figure 8. AC Coupled LVPECL to LVDS Interface
An AC coupled interface is preferred when transmitter and receiver ground references differ more than 1 V. This
is a likely scenario when transmitter and receiver devices are on separate PCBs. Figure 8 illustrates an AC
coupled interface between a LVPECL driver and LVDS receiver. R1 and R2, if not present in the driver device,
provide DC load for the emitter followers and may range between 140-220 ohms for most LVPECL devices for
this particular configuration. The DS08MB200 includes an internal 100 ohm resistor to terminate the transmission
line for minimal reflections. The signal after ac coupling capacitors will swing around a level set by internal
biasing resistors (i.e. fail-safe) which is either VDD/2 or 0 V depending on the actual failsafe implementation. If
internal biasing is not implemented, the signal common mode voltage will slowly wander to GND level.
8
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: DS08MB200
DS08MB200
www.ti.com
SNLS197D – MAY 2006 – REVISED MARCH 2013
Interfacing LVDS to LVPECL
An LVDS driver consists of a current source (nominal 3.5mA) which drives a CMOS differential pair. It needs a
differential resistive load in the range of 70 to 130 ohms to generate LVDS levels. In a system, the load should
be selected to match transmission line characteristic differential impedance so that the line is properly
terminated. The termination resistor should be placed as close to the receiver inputs as possible. When
interfacing an LVDS driver with a non-LVDS receiver, one only needs to bias the LVDS signal so that it is within
the common mode range of the receiver. This may be done by using separate biasing voltage which demands
another power supply. Some receivers have required biasing voltage available on-chip (VT, VTT or VBB).
50:
LVPECL
15MB200
50:
R1
50:
R2
50:
VT
Figure 9. DC Coupled LVDS to LVPECL Interface
Figure 9 illustrates interface between an LVDS driver and a LVPECL with a VT pin available. R1 and R2, if not
present in the receiver, provide proper resistive load for the driver and termination for the transmission line, and
VT sets desired bias for the receiver.
VDD
0.1PF
R1
83:
R2
83:
50:
LVPECL
15MB200
50:
0.1PF
R3
130:
R4
130:
Figure 10. AC Coupled LVDS to LVPECL Interface
Figure 10 illustrates AC coupled interface between an LVDS driver and LVPECL receiver without a VT pin
available. The resistors R1, R2, R3, and R4, if not present in the receiver, provide a load for the driver, terminate
the transmission line, and bias the signal for the receiver.
The bias networks shown above for LVPECL drivers and receivers may or may not be present within the driver
device. The LVPECL driver and receiver specification must be reviewed closely to ensure compatibility between
the driver and receiver terminations and common mode operating ranges.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: DS08MB200
9
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
DS08MB200TSQ/NOPB
ACTIVE
WQFN
RHS
48
250
Green (RoHS
& no Sb/Br)
CU SN
Level-3-260C-168 HR
-40 to 85
08MB200
DS08MB200TSQX/NOPB
ACTIVE
WQFN
RHS
48
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-3-260C-168 HR
-40 to 85
08MB200
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
Samples
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Mar-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
DS08MB200TSQ/NOPB
WQFN
RHS
48
250
178.0
16.4
7.3
7.3
1.3
12.0
16.0
Q1
DS08MB200TSQX/NOPB
WQFN
RHS
48
2500
330.0
16.4
7.3
7.3
1.3
12.0
16.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Mar-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
DS08MB200TSQ/NOPB
WQFN
RHS
DS08MB200TSQX/NOPB
WQFN
RHS
48
250
213.0
191.0
55.0
48
2500
367.0
367.0
38.0
Pack Materials-Page 2
MECHANICAL DATA
RHS0048A
SQA48A (Rev B)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
Similar pages