TI LMP7716MME/NOPB Single and dual precision, 17 mhz, low noise, cmos input amplifier Datasheet

LMP7715, LMP7716, LMP7716Q
www.ti.com
SNOSAV0E – MARCH 2006 – REVISED MARCH 2013
Single and Dual Precision, 17 MHz, Low Noise, CMOS Input Amplifiers
Check for Samples: LMP7715, LMP7716, LMP7716Q
FEATURES
DESCRIPTION
•
The LMP7715/LMP7716/LMP7716Q are single and
dual low noise, low offset, CMOS input, rail-to-rail
output precision amplifiers with high gain bandwidth
products. The LMP7715/LMP7716/LMP7716Q are
part of the LMP™ precision amplifier family and are
ideal for a variety of instrumentation applications.
1
23
Unless Otherwise Noted,
Typical Values at VS = 5V.
– Input Offset Voltage ±150 μV (Max)
– Input Bias Current 100 fA
– Input Voltage Noise 5.8 nV/√Hz
– Gain Bandwidth Product 17 MHz
– Supply Current (LMP7715) 1.15 mA
– Supply Current (LMP7716/LMP7716Q) 1.30
mA
– Supply Voltage Range 1.8V to 5.5V
– THD+N @ f = 1 kHz 0.001%
– Operating Temperature Range −40°C to
125°C
– Rail-to-rail Output Swing
– Space Saving SOT-23 Package (LMP7715)
– 8-Pin VSSOP Package
(LMP7716/LMP7716Q)
– LMP7716Q is AEC-Q100 Grade 1 Qualified
and is Manufactured on an Automotive
Grade Flow
APPLICATIONS
•
•
•
•
Active Filters and Buffers
Sensor Interface Applications
Transimpedance Amplifiers
Automotive
Utilizing
a
CMOS
input
stage,
the
LMP7715/LMP7716/LMP7716Q achieve an input bias
current of 100 fA, an input referred voltage noise of
5.8 nV/√Hz, and an input offset voltage of less than
±150
μV.
These
features
make
the
LMP7715/LMP7716/LMP7716Q superior choices for
precision applications.
Consuming only 1.15 mA of supply current, the
LMP7715 offers a high gain bandwidth product of 17
MHz, enabling accurate amplification at high closed
loop gains.
The LMP7715/LMP7716/LMP7716Q have a supply
voltage range of 1.8V to 5.5V, which makes these
ideal choices for portable low power applications with
low supply voltage requirements.
The LMP7715/LMP7716/LMP7716Q are built with
TI’s advanced VIP50 process technology. The
LMP7715 is offered in a 5-pin SOT-23 package and
the LMP7716/LMP7716Q is offered in an 8-pin
VSSOP.
The
LMP7716Q
incorporates
enhanced
manufacturing and support processes for the
automotive market, including defect detection
methodologies. Reliability qualification is compliant
with the requirements and temperature grades
defined in the AEC-Q100 standard.
1
2
3
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
LMP is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2006–2013, Texas Instruments Incorporated
LMP7715, LMP7716, LMP7716Q
SNOSAV0E – MARCH 2006 – REVISED MARCH 2013
www.ti.com
Typical Performance
PERCENTAGE (%)
20
100
VS = 5V
VS = 5.5V
VCM = VS/2
UNITS TESTED: 10,000
VOLTAGE NOISE (nV/ Hz)
25
15
10
5
0
-200
VS = 2.5V
10
1
-100
0
100
1
200
10
100
1k
10k
100k
FREQUENCY (Hz)
OFFSET VOLTAGE (PV)
Figure 1. Offset Voltage Distribution
Figure 2. Input Referred Voltage Noise
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings (1) (2)
Human Body Model
ESD Tolerance (3)
2000V
Machine Model
200V
Charge-Device Model
1000V
VIN Differential
±0.3V
Supply Voltage (VS = V+ – V−)
6.0V
+
−
Voltage on Input/Output Pins
V +0.3V, V −0.3V
Storage Temperature Range
−65°C to 150°C
Junction Temperature (4)
Soldering Information
(1)
(2)
(3)
(4)
+150°C
Infrared or Convection (20 sec)
235°C
Wave Soldering Lead Temp. (10 sec)
260°C
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the test
conditions, see the Electrical Characteristics Tables.
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
Human Body Model, applicable std. MIL-STD-883, Method 3015.7. Machine Model, applicable std. JESD22-A115-A (ESD MM std. of
JEDEC)Field-Induced Charge-Device Model, applicable std. JESD22-C101-C (ESD FICDM std. of JEDEC).
The maximum power dissipation is a function of TJ(MAX), θJA. The maximum allowable power dissipation at any ambient temperature is
PD = (TJ(MAX) - TA)/θJA. All numbers apply for packages soldered directly onto a PC Board.
Operating Ratings (1)
Temperature Range (2)
Supply Voltage (VS = V+ – V−)
Package Thermal Resistance (θJA (2))
(1)
(2)
2
−40°C to 125°C
0°C ≤ TA ≤ 125°C
1.8V to 5.5V
−40°C ≤ TA ≤ 125°C
2.0V to 5.5V
5-Pin SOT-23
180°C/W
8-Pin VSSOP
236°C/W
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the test
conditions, see the Electrical Characteristics Tables.
The maximum power dissipation is a function of TJ(MAX), θJA. The maximum allowable power dissipation at any ambient temperature is
PD = (TJ(MAX) - TA)/θJA. All numbers apply for packages soldered directly onto a PC Board.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LMP7715 LMP7716 LMP7716Q
LMP7715, LMP7716, LMP7716Q
www.ti.com
SNOSAV0E – MARCH 2006 – REVISED MARCH 2013
2.5V Electrical Characteristics
Unless otherwise specified, all limits are ensured for TA = 25°C, V+ = 2.5V, V− = 0V ,VO = VCM = V+/2. Boldface limits apply at
the temperature extremes.
Symbol
Parameter
Conditions
VOS
Min (1)
−20°C ≤ TA ≤ 85°C
Input Offset Voltage
−40°C ≤ TA ≤ 125°C
TC VOS
Input Offset Voltage Temperature
Drift (3) (4)
LMP7715
LMP7716/LMP7716Q
IB
VCM = 1.0V
IOS
Input Offset Current
VCM = 1V (4)
CMRR
Common Mode Rejection Ratio
0V ≤ VCM ≤ 1.4V
CMVR
AVOL
Open Loop Voltage Gain
VOUT
Output Voltage Swing
High
Output Voltage Swing
Low
IOUT
Output Current
IS
(2)
(3)
(4)
(5)
(6)
-1
±4
-1.75
0.05
1
100
0.006
0.5
50
83
80
100
2.0V ≤ V ≤ 5.5V
V− = 0V, VCM = 0
85
80
100
1.8V ≤ V+ ≤ 5.5V
V− = 0V, VCM = 0
85
98
−0.3
–0.3
Units
μV
μV/°C
pA
pA
dB
dB
1.5
1.5
LMP7715, VO = 0.15 to 2.2V
RL = 2 kΩ to V+/2
88
82
98
LMP7716/LMP7716Q, VO = 0.15 to 2.2V
RL = 2 kΩ to V+/2
84
80
92
LMP7715, VO = 0.15 to 2.2V
RL = 10 kΩ to V+/2
92
88
110
LMP7716/ LMP7716Q, VO = 0.15 to 2.2V
RL = 10 kΩ to V+/2
90
86
95
25
70
77
RL = 10 kΩ to V+/2
20
60
66
RL = 2 kΩ to V+/2
30
70
73
RL = 10 kΩ to V+/2
15
60
62
Sourcing to V−
VIN = 200 mV (6)
36
30
52
Sinking to V+
VIN = −200 mV (6)
7.5
5.0
15
1.30
1.65
1.10
1.50
1.85
8.3
AV = +1, Falling (90% to 10%)
10.3
mV from
either rail
mA
0.95
AV = +1, Rising (10% to 90%)
V
dB
RL = 2 kΩ to V+/2
LMP7716/LMP7716Q (per channel)
(1)
±180
±430
−40°C ≤ TA ≤ 125°C
LMP7715
Slew Rate
±20
1
25
Supply Current
SR
±180
±330
0.05
CMRR ≥ 80 dB
CMRR ≥ 78 dB
Common Mode Voltage Range
±20
−40°C ≤ TA ≤ 85°C
+
Power Supply Rejection Ratio
Max (1)
(4) (5)
Input Bias Current
PSRR
Typ (2)
mA
V/μs
Limits are 100% production tested at 25°C. Limits over the operating temperature range are specified through correlations using the
Statistical Quality Control (SQC) method.
Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary
over time and will also depend on the application and configuration. The typical values are not tested and are not specified on shipped
production material.
Offset voltage average drift is determined by dividing the change in VOS at the temperature extremes by the total temperature change.
This parameter is specified by design and/or characterization and is not tested in production.
Positive current corresponds to current flowing into the device.
The short circuit test is a momentary open loop test.
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LMP7715 LMP7716 LMP7716Q
Submit Documentation Feedback
3
LMP7715, LMP7716, LMP7716Q
SNOSAV0E – MARCH 2006 – REVISED MARCH 2013
www.ti.com
2.5V Electrical Characteristics (continued)
Unless otherwise specified, all limits are ensured for TA = 25°C, V+ = 2.5V, V− = 0V ,VO = VCM = V+/2. Boldface limits apply at
the temperature extremes.
Symbol
GBW
Parameter
Min (1)
Conditions
Gain Bandwidth
en
Max (1)
14
Input Referred Voltage Noise Density
in
Typ (2)
Input Referred Current Noise Density
THD+N
Total Harmonic Distortion + Noise
f = 400 Hz
6.8
f = 1 kHz
5.8
f = 1 kHz
0.01
f = 1 kHz, AV = 1, RL = 100 kΩ
VO = 0.9 VPP
0.003
f = 1 kHz, AV = 1, RL = 600Ω
VO = 0.9 VPP
0.004
Units
MHz
nV/
pA/√Hz
%
5V Electrical Characteristics
Unless otherwise specified, all limits are ensured for TA = 25°C, V+ = 5V, V− = 0V, VCM = V+/2. Boldface limits apply at the
temperature extremes.
Symbol
VOS
Typ (2)
Max (1)
−20°C ≤ TA ≤ 85°C
±10
±150
±300
−40°C ≤ TA ≤ 125°C
±10
±150
±400
-1
±4
Parameter
Min (1)
Conditions
Input Offset Voltage
TC VOS Input Offset Voltage Temperature
Drift (3) (4)
LMP7715
LMP7716/LMP7716Q
IB
-1.75
−40°C ≤ TA ≤ 85°C
Input Bias Current
VCM = 2.0V
−40°C ≤ TA ≤ 125°C
IOS
CMRR
4
0.01
0.5
50
0V ≤ VCM ≤ 3.7V
85
82
100
2.0V ≤ V+ ≤ 5.5V
V− = 0V, VCM = 0
85
80
100
1.8V ≤ V+ ≤ 5.5V
V− = 0V, VCM = 0
85
98
Common Mode Voltage Range
Open Loop Voltage Gain
(3)
(4)
(5)
1
100
Common Mode Rejection Ratio
AVOL
(2)
0.1
VCM = 2.0V (4)
Power Supply Rejection Ratio
(1)
1
25
Input Offset Current
PSRR
CMVR
0.1
(4) (5)
CMRR ≥ 80 dB
CMRR ≥ 78 dB
−0.3
–0.3
88
82
107
LMP7716/LMP7716Q, VO = 0.3 to 4.7V
RL = 2 kΩ to V+/2
84
80
90
LMP7715, VO = 0.3 to 4.7V
RL = 10 kΩ to V+/2
92
88
110
LMP7716/LMP7716Q, VO = 0.3 to 4.7V
RL = 10 kΩ to V+/2
90
86
95
μV
μV/°C
pA
pA
dB
dB
4
4
LMP7715, VO = 0.3 to 4.7V
RL = 2 kΩ to V+/2
Units
V
dB
Limits are 100% production tested at 25°C. Limits over the operating temperature range are specified through correlations using the
Statistical Quality Control (SQC) method.
Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary
over time and will also depend on the application and configuration. The typical values are not tested and are not specified on shipped
production material.
Offset voltage average drift is determined by dividing the change in VOS at the temperature extremes by the total temperature change.
This parameter is specified by design and/or characterization and is not tested in production.
Positive current corresponds to current flowing into the device.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LMP7715 LMP7716 LMP7716Q
LMP7715, LMP7716, LMP7716Q
www.ti.com
SNOSAV0E – MARCH 2006 – REVISED MARCH 2013
5V Electrical Characteristics (continued)
Unless otherwise specified, all limits are ensured for TA = 25°C, V+ = 5V, V− = 0V, VCM = V+/2. Boldface limits apply at the
temperature extremes.
Symbol
Typ (2)
Max (1)
RL = 2 kΩ to V+/2
32
70
77
RL = 10 kΩ to V+/2
22
60
66
RL = 2 kΩ to V+/2
(LMP7715)
42
70
73
RL = 2 kΩ to V+/2
(LMP7716/LMP7716Q)
45
75
78
RL = 10 kΩ to V+/2
20
60
62
Parameter
Min (1)
Conditions
VOUT
Output Voltage Swing
High
Output Voltage Swing
Low
IOUT
Output Current
IS
Sourcing to V−
VIN = 200 mV (6)
46
38
66
Sinking to V+
VIN = −200 mV (6)
10.5
6.5
23
LMP7715
Supply Current
LMP7716/LMP7716Q (per channel)
SR
Slew Rate
GBW
en
1.70
2.05
AV = +1, Falling (90% to 10%)
7.5
11.5
Input Referred Current Noise Density
Total Harmonic Distortion + Noise
f = 400 Hz
7.0
f = 1 kHz
5.8
f = 1 kHz
0.01
f = 1 kHz, AV = 1, RL = 100 kΩ
VO = 4 VPP
0.001
f = 1 kHz, AV = 1, RL = 600Ω
VO = 4 VPP
0.004
mA
V/μs
17
THD+N
(6)
1.30
9.5
Gain Bandwidth
Input Referred Voltage Noise Density
in
1.40
1.75
6.0
mV from
either rail
mA
1.15
AV = +1, Rising (10% to 90%)
Units
MHz
nV/√Hz
pA/√Hz
%
The short circuit test is a momentary open loop test.
Connection Diagram
5-Pin SOT-23
5
1
+
V
OUT A
-IN A
V
-
2
7
+
+
V
OUT B
2
+
+IN
8
1
-
OUTPUT
8-Pin VSSOP
+IN A
4
3
Figure 3. Top View
-IN
V
-
3
4
+-
6
5
-IN B
+IN B
Figure 4. Top View
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LMP7715 LMP7716 LMP7716Q
Submit Documentation Feedback
5
LMP7715, LMP7716, LMP7716Q
SNOSAV0E – MARCH 2006 – REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics
Unless otherwise noted: TA = 25°C, VS = 5V, VCM = VS/2.
Offset Voltage Distribution
PERCENTAGE (%)
20
TCVOS Distribution (LMP7715)
25
VS = 2.5V
-40°C d TA d 125qC
VCM = VS/2
UNITS TESTED:10,000
VS = 2.5V, 5V
20
PERCENTAGE (%)
25
15
10
5
VCM = VS/2
UNITS TESTED:
10,000
15
10
5
0
-200
0
-100
0
100
200
-3
-4
-2
-1
0
TCVOS (PV/°C)
OFFSET VOLTAGE (PV)
Figure 5.
TCVOS Distribution (LMP7716/LMP7716Q)
25
-40°C d TA d 125°C
VS = 2.5V, 5V
VS = 5V
VCM = VS/2
UNITS TESTED: 10,000
PERCENTAGE (%)
PERCENTAGE (%)
20
15
10
20 VCM = VS/2
UNITS TESTED:
10,000
15
10
5
5
0
-200
0
-100
0
100
-4
200
-3
-2
-1
Figure 7.
Figure 8.
Offset Voltage vs. VCM
Offset Voltage vs. VCM
200
200
VS = 1.8V
VS = 2.5V
150
-40°C
OFFSET VOLTAGE (PV)
OFFSET VOLTAGE (PV)
150
100
50
25°C
0
-50
125°C
-100
-40°C
100
25°C
50
0
125°C
-50
-100
-150
-150
-200
-0.3
0
TCVOS (PV/°C)
OFFSET VOLTAGE (PV)
0
0.3
0.9
0.6
1.2
1.5
-200
-0.3
0
VCM (V)
Submit Documentation Feedback
0.3
0.6
0.9
1.2
1.5
1.8
2.1
VCM (V)
Figure 9.
6
2
Figure 6.
Offset Voltage Distribution
25
1
Figure 10.
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LMP7715 LMP7716 LMP7716Q
LMP7715, LMP7716, LMP7716Q
www.ti.com
SNOSAV0E – MARCH 2006 – REVISED MARCH 2013
Typical Performance Characteristics (continued)
Unless otherwise noted: TA = 25°C, VS = 5V, VCM = VS/2.
Offset Voltage vs. VCM
Offset Voltage vs. Supply Voltage
200
200
VS = 5V
150
100
-40°C
50
25°C
OFFSET VOLTAGE (PV)
OFFSET VOLTAGE (PV)
150
0
125°C
-50
-100
-150
100
-40°C
50
25°C
0
125°C
-50
-100
-150
-200
-0.3
-200
0.7
1.7
2.7
3.7
4.7
1.5
2.5
3.5
4.5
VS (V)
VCM (V)
Figure 11.
6
Figure 12.
Offset Voltage vs. Temperature
CMRR vs. Frequency
150
120
100
100
VS = 2.5V
50
VS = 2.5V
0
80
CMRR (dB)
OFFSET VOLTAGE (PV)
5.5
LMP7711
-50
VS = 5V
60
40
-100
VS = 5V
20
-150
LMP7712
-200
-40 -20
0
20
40
60
0
10
80 100 120 125
100k
1M
FREQUENCY (Hz)
TEMPERATURE (°C)
Figure 13.
Figure 14.
Input Bias Current vs. VCM
Input Bias Current vs. VCM
50
1000
VS = 5V
0
-500
-40°C
-1000
VS = 5V
40
INPUT BIAS CURRENT (pA)
25°C
500
INPUT BIAS CURRENT (fA)
10k
1k
100
-1500
-2000
-2500
30
20
125°C
10
0
-10
85°C
-20
-30
-40
-50
-3000
0
1
2
3
4
0
1
2
3
4
VCM (V)
VCM (V)
Figure 15.
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LMP7715 LMP7716 LMP7716Q
Figure 16.
Submit Documentation Feedback
7
LMP7715, LMP7716, LMP7716Q
SNOSAV0E – MARCH 2006 – REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics (continued)
Unless otherwise noted: TA = 25°C, VS = 5V, VCM = VS/2.
Supply Current vs. Supply Voltage (LMP7715)
Supply Current vs. Supply Voltage (LMP7716/LMP7716Q)
2
2
1.6
1.6
SUPPLY CURRENT (mA)
SUPPLY CURRENT (mA)
125°C
125°C
25°C
1.2
0.8
-40°C
0.4
25°C
1.2
-40°C
0.8
0.4
0
0
1.5
2.5
3.5
4.5
5.5
1.5
Figure 18.
140
70
120
60
100
80
60
30
20
10
1M
10M
0
1.5
100M
-40°C
25°C
40
20
0
125°C
50
40
100k
5.5
Sourcing Current vs. Supply Voltage
80
ISOURCE (mA)
CROSSTALK REJECTION RATIO (dB)
4.5
Figure 17.
160
10k
3.5
VS (V)
Crosstalk Rejection Ratio (LMP7716/LMP7716Q)
1k
2.5
VS (V)
2.5
3.5
FREQUENCY (Hz)
4.5
5.5
VS (V)
Figure 19.
Figure 20.
Sinking Current vs. Supply Voltage
Sourcing Current vs. Output Voltage
35
70
30
60
125°C
125°C
20
50
ISOURCE (mA)
ISINK (mA)
25
25°C
15
10
8
25°C
30
20
-40°C
5
0
1.5
-40°C
40
10
0
2.5
3.5
4.5
5.5
0
1
2
3
VS (V)
VOUT (V)
Figure 21.
Figure 22.
Submit Documentation Feedback
4
5
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LMP7715 LMP7716 LMP7716Q
LMP7715, LMP7716, LMP7716Q
www.ti.com
SNOSAV0E – MARCH 2006 – REVISED MARCH 2013
Typical Performance Characteristics (continued)
Unless otherwise noted: TA = 25°C, VS = 5V, VCM = VS/2.
Sinking Current vs. Output Voltage
Output Swing High vs. Supply Voltage
30
50
RL = 10 k:
VOUT FROM RAIL (mV)
125°C
25
ISINK (mA)
20
25°C
15
10
-40°C
40
30
25°C
125°C
20
-40°C
10
5
0
0
0
1
2
3
4
5
1.5
2.5
3.5
4.5
Figure 23.
Figure 24.
Output Swing Low vs. Supply Voltage
Output Swing High vs. Supply Voltage
50
50
40
30
-40°C
20
125°C
10
RL = 2 k:
VOUT FROM RAIL (mV)
VOUT FROM RAIL (mV)
RL =10 k:
40
125°C
25°C
30
20
-40°C
10
25°C
0
0
1.5
2.5
3.5
4.5
5.5
1.5
2.5
3.5
VS (V)
4.5
5.5
VS (V)
Figure 25.
Figure 26.
Output Swing Low vs. Supply Voltage
Output Swing High vs. Supply Voltage
50
150
RL = 600:
-40°C
40
VOUT FROM RAIL (mV)
VOUT FROM RAIL (mV)
5.5
VS (V)
VOUT (V)
125°C
30
25°C
20
10
120
90
125°C
25°C
60
30
-40°C
RL = 2 k:
0
1.5
0
2.5
3.5
4.5
5.5
1.5
2.5
3.5
4.5
5.5
VS (V)
VS (V)
Figure 27.
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LMP7715 LMP7716 LMP7716Q
Figure 28.
Submit Documentation Feedback
9
LMP7715, LMP7716, LMP7716Q
SNOSAV0E – MARCH 2006 – REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics (continued)
Unless otherwise noted: TA = 25°C, VS = 5V, VCM = VS/2.
Output Swing Low vs. Supply Voltage
Open Loop Frequency Response
120
120
100
CL = 20 pF
80
25°C
-40°C
60
CL = 50 pF
60
125°C
90
GAIN
40
20
-20
CL = 50 pF
-40
CL = 100 pF
-60
100M
-60
1.5
2.5
3.5
4.5
1k
5.5
10k
VS (V)
100k
Open Loop Frequency Response
Phase Margin vs. Capacitive Load
50
120
PHASE
100
60
60
40
40
GAIN
20
20
0
0
-20
-20
-40
-40
10M
40
PHASE MARGIN (°)
80
PHASE (°)
80
RL = 600: 10 k: 10 M:
-60
10k
100k
1M
10M
Figure 30.
120
100
1M
FREQUENCY (Hz)
Figure 29.
GAIN (dB)
0
CL = 20 pF
-40
RL = 600:
30
RL = 10 k:
RL = 10 M:
20
10
VS = 2.5V
0
-60
100M
10
100
1000
CAPACITIVE LOAD (pF)
FREQUENCY (Hz)
Figure 31.
Figure 32.
Phase Margin vs. Capacitive Load
Overshoot and Undershoot vs. Capacitive Load
50
OVERSHOOT AND UNDERSHOOT (%)
70
RL = 600:
40
PHASE MARGIN (°)
40
20
0
0
80
60
CL = 100 pF
-20
30
RL = 10 k:
30
20
RL = 10 M:
10
VS = 5V
0
100
1000
CAPACITIVE LOAD (pF)
UNDERSHOOT%
60
50
OVERSHOOT %
40
30
20
10
0
10
0
20
40
Submit Documentation Feedback
60
80
100
120
CAPACITIVE LOAD (pF)
Figure 33.
10
120
PHASE
100
GAIN (dB)
VOUT FROM RAIL (mV)
RL = 600:
PHASE (°)
150
Figure 34.
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LMP7715 LMP7716 LMP7716Q
LMP7715, LMP7716, LMP7716Q
www.ti.com
SNOSAV0E – MARCH 2006 – REVISED MARCH 2013
Typical Performance Characteristics (continued)
Unless otherwise noted: TA = 25°C, VS = 5V, VCM = VS/2.
Slew Rate vs. Supply Voltage
Small Signal Step Response
12
FALLING EDGE
10 mV/DIV
SLEW RATE (V/Ps)
11
10
9
RISING EDGE
VIN = 20 mVPP
8
f = 1 MHz, AV = +1
VS = 2.5V, CL = 10 pF
7
1.5
2.5
3.5
4.5
5.5
200 ns/DIV
6
VS (V)
Figure 36.
Large Signal Step Response
Small Signal Step Response
10 mV/DIV
200 mV/DIV
Figure 35.
VIN = 1 VPP
VIN = 20 mVPP
f = 200 kHz, AV = +1
f = 1 MHz, AV = +1
VS = 2.5V, CL = 10 pF
VS = 5V, CL = 10 pF
800 ns/DIV
200 ns/DIV
Figure 37.
Figure 38.
Large Signal Step Response
THD+N vs. Output Voltage
0
THD+N (dB)
200 mV/DIV
-20
VS = 1.8V
f = 1 kHz
AV = +2
-40
-60
RL = 600:
-80
VIN = 1 VPP
f = 200 kHz, AV = +1
VS = 5V, CL = 10 pF
-100
RL = 100 k:
-120
0.01
800 ns/DIV
0.1
1
10
OUTPUT AMPLITUDE (VPP)
Figure 39.
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LMP7715 LMP7716 LMP7716Q
Figure 40.
Submit Documentation Feedback
11
LMP7715, LMP7716, LMP7716Q
SNOSAV0E – MARCH 2006 – REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics (continued)
Unless otherwise noted: TA = 25°C, VS = 5V, VCM = VS/2.
THD+N vs. Output Voltage
THD+N vs. Frequency
0.006
0
VS = 5.5V
f = 1 kHz
-20
VS = 1.8V
VO = 0.9 VPP
0.005
AV = +2
AV = +2
0.004
THD+N (%)
THD+N (dB)
-40
RL = 600:
-60
RL = 600:
-80
RL = 100 k:
0.003
0.002
-100
0.001
-120
RL = 100 k:
-140
0.01
0.1
1
0
10
10
100
1k
10k
100k
FREQUENCY (Hz)
OUTPUT AMPLITUDE (VPP)
Figure 41.
Figure 42.
THD+N vs. Frequency
PSRR vs. Frequency
120
0.006
VS = 5V
VS = 5.5V, -PSRR
VO = 4 VPP
0.005
VS = 1.8V, -PSRR
100
AV = +2
80
PSRR (dB)
THD+N (%)
0.004
RL = 600:
0.003
VS = 5.5V, +PSRR
60
0.002
40
0.001
20
VS = 1.8V, +PSRR
RL = 100 k:
0
0
10
100
1k
10k
100k
10
100
FREQUENCY (Hz)
1k
10k
100k
Figure 43.
Figure 44.
Input Referred Voltage Noise vs. Frequency
Time Domain Voltage Noise
100
VCM = 0.0V
400 nV/DIV
VS = 2.5V
10
1
1
10
100
10M
VS = ±2.5V
VS = 5.5V
VOLTAGE NOISE (nV/ Hz)
1M
FREQUENCY (Hz)
1k
10k
1 s/DIV
100k
FREQUENCY (Hz)
Figure 45.
12
Submit Documentation Feedback
Figure 46.
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LMP7715 LMP7716 LMP7716Q
LMP7715, LMP7716, LMP7716Q
www.ti.com
SNOSAV0E – MARCH 2006 – REVISED MARCH 2013
Typical Performance Characteristics (continued)
Unless otherwise noted: TA = 25°C, VS = 5V, VCM = VS/2.
Closed Loop Frequency Response
RL = 2 k:
180
3
CL = 20 pF
135
2
VO = 2 VPP
90
AV = +1
45
0
0
-1
-45
PHASE
-2
-90
-135
-3
GAIN
-4
-5
100
1k
100
10k
100 k
1M
OUTPUT IMPEDANCE (:)
VS = 5V
4
1
Closed Loop Output Impedance vs. Frequency
225
PHASE (°)
GAIN (dB)
5
10
1
0.1
-180
-225
10M
0.01
10
100
1k
10k 100k
1M
10M 100M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 47.
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LMP7715 LMP7716 LMP7716Q
Figure 48.
Submit Documentation Feedback
13
LMP7715, LMP7716, LMP7716Q
SNOSAV0E – MARCH 2006 – REVISED MARCH 2013
www.ti.com
APPLICATION INFORMATION
LMP7715/LMP7716/LMP7716Q
The LMP7715/LMP7716/LMP7716Q are single and dual, low noise, low offset, rail-to-rail output precision
amplifiers with a wide gain bandwidth product of 17 MHz and low supply current. The wide bandwidth makes the
LMP7715/LMP7716/LMP7716Q ideal choices for wide-band amplification in portable applications.
The LMP7715/LMP7716/LMP7716Q are superior for sensor applications. The very low input referred voltage
noise of only 5.8 nV/√Hz at 1 kHz and very low input referred current noise of only 10 fA/√Hz mean more signal
fidelity and higher signal-to-noise ratio.
The LMP7715/LMP7716/LMP7716Q have a supply voltage range of 1.8V to 5.5V over a wide temperature range
of 0°C to 125°C. This is optimal for low voltage commercial applications. For applications where the ambient
temperature might be less than 0°C, the LMP7715/LMP7716/LMP7716Q are fully operational at supply voltages
of 2.0V to 5.5V over the temperature range of −40°C to 125°C.
The outputs of the LMP7715/LMP7716/LMP7716Q swing within 25 mV of either rail providing maximum dynamic
range in applications requiring low supply voltage. The input common mode range of the
LMP7715/LMP7716/LMP7716Q extends to 300 mV below ground. This feature enables users to utilize this
device in single supply applications.
The use of a very innovative feedback topology has enhanced the current drive capability of the
LMP7715/LMP7716/LMP7716Q, resulting in sourcing currents of as much as 47 mA with a supply voltage of only
1.8V.
The LMP7715 is offered in the space saving SOT-23 package and the LMP7716/LMP7716Q is offered in an 8pin VSSOP. These small packages are ideal solutions for applications requiring minimum PC board footprint.
CAPACITIVE LOAD
The unity gain follower is the most sensitive configuration to capacitive loading. The combination of a capacitive
load placed directly on the output of an amplifier along with the output impedance of the amplifier creates a
phase lag which in turn reduces the phase margin of the amplifier. If phase margin is significantly reduced, the
response will be either underdamped or the amplifier will oscillate.
The LMP7715/LMP7716/LMP7716Q can directly drive capacitive loads of up to 120 pF without oscillating. To
drive heavier capacitive loads, an isolation resistor, RISO as shown in Figure 49, should be used. This resistor
and CL form a pole and hence delay the phase lag or increase the phase margin of the overall system. The
larger the value of RISO, the more stable the output voltage will be. However, larger values of RISO result in
reduced output swing and reduced output current drive.
Figure 49. Isolating Capacitive Load
INPUT CAPACITANCE
CMOS input stages inherently have low input bias current and higher input referred voltage noise. The
LMP7715/LMP7716/LMP7716Q enhance this performance by having the low input bias current of only 50 fA, as
well as, a very low input referred voltage noise of 5.8 nV/√Hz. In order to achieve this a larger input stage has
been used. This larger input stage increases the input capacitance of the LMP7715/LMP7716/LMP7716Q.
Figure 50 shows typical input common mode capacitance of the LMP7715/LMP7716/LMP7716Q.
14
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LMP7715 LMP7716 LMP7716Q
LMP7715, LMP7716, LMP7716Q
www.ti.com
SNOSAV0E – MARCH 2006 – REVISED MARCH 2013
25
VS = 5V
CCM (pF)
20
15
10
5
0
0
1
2
3
4
VCM (V)
Figure 50. Input Common Mode Capacitance
This input capacitance will interact with other impedances, such as gain and feedback resistors which are seen
on the inputs of the amplifier, to form a pole. This pole will have little or no effect on the output of the amplifier at
low frequencies and under DC conditions, but will play a bigger role as the frequency increases. At higher
frequencies, the presence of this pole will decrease phase margin and also cause gain peaking. In order to
compensate for the input capacitance, care must be taken in choosing feedback resistors. In addition to being
selective in picking values for the feedback resistor, a capacitor can be added to the feedback path to increase
stability.
The DC gain of the circuit shown in Figure 51 is simply −R2/R1.
CF
R2
R1
-
+
CIN
VIN
+
+
-
-
AV = -
VOUT
VIN
=-
VOUT
R2
R1
Figure 51. Compensating for Input Capacitance
For the time being, ignore CF. The AC gain of the circuit in Figure 51 can be calculated as follows:
-R2/R1
(s) =
1+
s2
s
+
§ A0 R 1
§ A0
¨
¨C R
© R1 + R2
© IN 2
§
¨
©
VIN
§
¨
©
VOUT
(1)
This equation is rearranged to find the location of the two poles:
1
1
+
r
R1
R2
§1
1
+
¨
R
R
© 1
2
§
¨
©
-1
P1,2 =
2CIN
2
-
4 A0CIN
R2
(2)
As shown in Equation 2, as the values of R1 and R2 are increased, the magnitude of the poles are reduced,
which in turn decreases the bandwidth of the amplifier. Figure 52 shows the frequency response with different
value resistors for R1 and R2. Whenever possible, it is best to chose smaller feedback resistors.
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LMP7715 LMP7716 LMP7716Q
Submit Documentation Feedback
15
LMP7715, LMP7716, LMP7716Q
SNOSAV0E – MARCH 2006 – REVISED MARCH 2013
www.ti.com
15
AV = -1
10
GAIN (dB)
5
0
-5
R1, R2 = 30 k:
-10
R1, R2 = 10 k:
-15
R1, R2 = 1 k:
-20
-25
10k
100k
1M
10M
100M
FREQUENCY (Hz)
Figure 52. Closed Loop Frequency Response
As mentioned before, adding a capacitor to the feedback path will decrease the peaking. This is because CF will
form yet another pole in the system and will prevent pairs of poles, or complex conjugates from forming. It is the
presence of pairs of poles that cause the peaking of gain. Figure 53 shows the frequency response of the
schematic presented in Figure 51 with different values of CF. As can be seen, using a small value capacitor
significantly reduces or eliminates the peaking.
20
R1, R2 = 30 k:
10
CF = 0 pF
AV = -1
GAIN (dB)
0
CF = 5 pF
-10
CF = 2 pF
-20
-30
-40
10k
100k
1M
10M
FREQUENCY (Hz)
Figure 53. Closed Loop Frequency Response
TRANSIMPEDANCE AMPLIFIER
In many applications the signal of interest is a very small amount of current that needs to be detected. Current
that is transmitted through a photodiode is a good example. Barcode scanners, light meters, fiber optic receivers,
and industrial sensors are some typical applications utilizing photodiodes for current detection. This current
needs to be amplified before it can be further processed. This amplification is performed using a current-tovoltage converter configuration or transimpedance amplifier. The signal of interest is fed to the inverting input of
an op amp with a feedback resistor in the current path. The voltage at the output of this amplifier will be equal to
the negative of the input current times the value of the feedback resistor. Figure 54 shows a transimpedance
amplifier configuration. CD represents the photodiode parasitic capacitance and CCM denotes the common-mode
capacitance of the amplifier. The presence of all of these capacitances at higher frequencies might lead to less
stable topologies at higher frequencies. Care must be taken when designing a transimpedance amplifier to
prevent the circuit from oscillating.
With a wide gain bandwidth product, low input bias current and low input voltage and current noise, the
LMP7715/LMP7716/LMP7716Q are ideal for wideband transimpedance applications.
16
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LMP7715 LMP7716 LMP7716Q
LMP7715, LMP7716, LMP7716Q
www.ti.com
SNOSAV0E – MARCH 2006 – REVISED MARCH 2013
CF
RF
IIN
CCM
+
+
VOUT
CD
-
VB
CIN = CD + CCM
VOUT
= - RF
IIN
Figure 54. Transimpedance Amplifier
A feedback capacitance CF is usually added in parallel with RF to maintain circuit stability and to control the
frequency response. To achieve a maximally flat, 2nd order response, RF and CF should be chosen by using
Equation 3
CF =
CIN
GBWP
2 S RF
(3)
Calculating CF from Equation 3 can sometimes result in capacitor values which are less than 2 pF. This is
especially the case for high speed applications. In these instances, it is often more practical to use the circuit
shown in Figure 55 in order to allow more sensible choices for CF. The new feedback capacitor, CF′, is (1+
RB/RA) CF. This relationship holds as long as RA << RF.
RA
RB
CF
RF
+
IF RA < < RF
RB
§
CF
CFc = ¨1 +
RA
©
§
¨
©
Figure 55. Modified Transimpedance Amplifier
SENSOR INTERFACE
The LMP7715/LMP7716/LMP7716Q have low input bias current and low input referred noise, which make them
ideal choices for sensor interfaces such as thermopiles, Infra Red (IR) thermometry, thermocouple amplifiers,
and pH electrode buffers.
Thermopiles generate voltage in response to receiving radiation. These voltages are often only a few microvolts.
As a result, the operational amplifier used for this application needs to have low offset voltage, low input voltage
noise, and low input bias current. Figure 56 shows a thermopile application where the sensor detects radiation
from a distance and generates a voltage that is proportional to the intensity of the radiation. The two resistors, RA
and RB, are selected to provide high gain to amplify this signal, while CF removes the high frequency noise.
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LMP7715 LMP7716 LMP7716Q
Submit Documentation Feedback
17
LMP7715, LMP7716, LMP7716Q
SNOSAV0E – MARCH 2006 – REVISED MARCH 2013
www.ti.com
THERMOPILE
+
+
-
VIN = KI
IR RADIATION
INTENSITY, I
+
RB
-
VOUT
RA
CF
VOUT RA
I=
K(RA + RB)
Figure 56. Thermopile Sensor Interface
PRECISION RECTIFIER
Rectifiers are electrical circuits used for converting AC signals to DC signals. Figure 57 shows a full-wave
precision rectifier. Each operational amplifier used in this circuit has a diode on its output. This means for the
diodes to conduct, the output of the amplifier needs to be positive with respect to ground. If VIN is in its positive
half cycle then only the output of the bottom amplifier will be positive. As a result, the diode on the output of the
bottom amplifier will conduct and the signal will show at the output of the circuit. If VIN is in its negative half cycle
then the output of the top amplifier will be positive, resulting in the diode on the output of the top amplifier
conducting and delivering the signal from the amplifier's output to the circuit's output.
For R2/ R1 ≥ 2, the resistor values can be found by using the equation shown in Figure 57. If R2/ R1 = 1, then R3
should be left open, no resistor needed, and R4 should simply be shorted.
VIN
R2
R1
V
+
VOUT
+
-
R3
V
R4
R2
+
R1
-
10 k:
R4
=1+
R3
V
+
V
Figure 57. Precision Rectifier
18
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LMP7715 LMP7716 LMP7716Q
LMP7715, LMP7716, LMP7716Q
www.ti.com
SNOSAV0E – MARCH 2006 – REVISED MARCH 2013
REVISION HISTORY
Changes from Revision D (March 2013) to Revision E
•
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 18
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LMP7715 LMP7716 LMP7716Q
Submit Documentation Feedback
19
PACKAGE OPTION ADDENDUM
www.ti.com
25-Feb-2015
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LMP7715MF/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
AV3A
LMP7715MFE/NOPB
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
AV3A
LMP7715MFX/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
AV3A
LMP7716MM/NOPB
ACTIVE
VSSOP
DGK
8
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
AX3A
LMP7716MME/NOPB
ACTIVE
VSSOP
DGK
8
250
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
AX3A
LMP7716MMX/NOPB
ACTIVE
VSSOP
DGK
8
3500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
AX3A
LMP7716QMM/NOPB
ACTIVE
VSSOP
DGK
8
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
AR5A
LMP7716QMME/NOPB
ACTIVE
VSSOP
DGK
8
250
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
AR5A
LMP7716QMMX/NOPB
ACTIVE
VSSOP
DGK
8
3500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
AR5A
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
25-Feb-2015
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF LMP7716, LMP7716-Q1 :
• Catalog: LMP7716
• Automotive: LMP7716-Q1
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
5-Dec-2014
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
LMP7715MF/NOPB
SOT-23
DBV
5
1000
178.0
8.4
LMP7715MFE/NOPB
SOT-23
DBV
5
250
178.0
LMP7715MFX/NOPB
SOT-23
DBV
5
3000
178.0
LMP7716MM/NOPB
VSSOP
DGK
8
1000
LMP7716MME/NOPB
VSSOP
DGK
8
W
Pin1
(mm) Quadrant
3.2
3.2
1.4
4.0
8.0
Q3
8.4
3.2
3.2
1.4
4.0
8.0
Q3
8.4
3.2
3.2
1.4
4.0
8.0
Q3
178.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
250
178.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LMP7716MMX/NOPB
VSSOP
DGK
8
3500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LMP7716QMM/NOPB
VSSOP
DGK
8
1000
178.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LMP7716QMME/NOPB
VSSOP
DGK
8
250
178.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
LMP7716QMMX/NOPB
VSSOP
DGK
8
3500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
5-Dec-2014
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LMP7715MF/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LMP7715MFE/NOPB
SOT-23
DBV
5
250
210.0
185.0
35.0
LMP7715MFX/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LMP7716MM/NOPB
VSSOP
DGK
8
1000
210.0
185.0
35.0
LMP7716MME/NOPB
VSSOP
DGK
8
250
210.0
185.0
35.0
LMP7716MMX/NOPB
VSSOP
DGK
8
3500
367.0
367.0
35.0
LMP7716QMM/NOPB
VSSOP
DGK
8
1000
210.0
185.0
35.0
LMP7716QMME/NOPB
VSSOP
DGK
8
250
210.0
185.0
35.0
LMP7716QMMX/NOPB
VSSOP
DGK
8
3500
367.0
367.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
Similar pages