NCP51530 Product Preview High Frequency, 700 V- 2 A High and Low Side Driver NCP51530 is a 700 V high side and low side driver with 2 A current drive capability for AC−DC power supplies and inverters. NCP51530 offers best in class propagation delay, low quiescent current and low switching current at high frequencies of operation. This device is tailored for highly efficient power supplies operating at high frequencies. NCP51530 is offered in two versions, NCP51530A/B. NCP51530A has a typical 60 ns propagation delay, while NCP51530B has a typical propagation delay of 25 ns. NCP51530 comes in SOIC8 and DFN10 packages. www.onsemi.com MARKING DIAGRAMS 8 1 SOIC−8 D SUFFIX CASE 751−07 NCP51530x ALYW G Features • • • • • • • • • • • • • High voltage range: Up to 700 V NCP51530A: Typical 60 ns Propagation Delay NCP51530B: Typical 25 ns Propagation Delay Low Quiescent and Operating Currents 15 ns Rise and Fall Time 2.2 A/1.7 A Source/sink Currents Under−voltage Lockout for Both Channels 3.3 V and 5 V Input Logic Compatible High dv/dt Immunity up to 50 V/ns Pin to Pin Compatible with Industry Standard Half−bridge ICs. Matched Propagation Delay (7 ns Max) High Negative Transient Immunity on Bridge Pin DFN10 Package Offers Both Improved Creepage and Exposed Pad 1 51530x ALYWG G DFN10 MN SUFFIX CASE 506DJ NCP5106 x A WL YY WW G = Specific Device Code = A or B version = Assembly Location = Wafer Lot = Year = Work Week = Pb−Free Package (Note: Microdot may be in either location) PINOUT INFORMATION Applications • • • • • 1 HIN LIN GND LO High−density SMPS for Servers, Telecom and Industrial Half/Full−bridge & LLC Converters Active Clamp Flyback/Forward Converters Solar Inverters & Motor Controls Electric Power Steering VB HO HB VCC 1 8 Pin Package (Top View) This document contains information on a product under development. ON Semiconductor reserves the right to change or discontinue this product without notice. VCC HIN LIN GND GND 1 VB HO HB NC LO 10 Pin DFN Package (Top View) ORDERING INFORMATION See detailed ordering and shipping information on page 23 of this data sheet. © Semiconductor Components Industries, LLC, 2018 March, 2018 − Rev. P0 1 Publication Order Number: NCP51530/D NCP51530 HIN VB LIN HO GND HB LO VCC VCC VB HIN HO LIN HB GND NC GND LO SOIC8 (Top View) DFN10 (Top View) Table 1. PIN DESCRIPTION SOIC 8 PACKAGE Pin Out Name Function 1 HIN High side input 2 LIN Low side input 3 GND 4 LO 5 VCC 6 HB High side supply return 7 HO High side output 8 VB High side voltage supply Ground reference Low side output Low side and logic supply Table 2. PIN DESCRIPTION DFN10 PACKAGE Pin Out Name Function 1 VCC Low side and logic supply 2 HIN High side input 3 LIN Low side input 4 GND Ground reference 5 GND Ground reference 6 LO Low side output 7 NC No Connect 8 HB High side supply return 9 HO High side output 10 VB High side voltage supply www.onsemi.com 2 NCP51530 VHV ADRV LDRV PWM CONTROLLER COMP HIN VB LIN HO NCP51530 GND HB LO VCC Figure 1. Simplified Applications Schematic for a Half−Bridge Converter (SOIC8) www.onsemi.com 3 NCP51530 VHV VCC VB HIN HO LIN HB GND NC GND LO VCC HIN LIN GND GND VB HO HB NC LO LIN 1 HIN 1 LIN 2 Micro Controller Digital Isolator HIN 2 Figure 2. Simplified Applications Schematic for a Full Bridge Converter (DFN 10) www.onsemi.com 4 NCP51530 VCC VB UV Detect Pulse Trigg er HIN Level Shifter S Q R Q HO r UV DETECT HB VCC LO DELAY LIN r GND Figure 3. Internal Block Diagram for NCP51530 Table 3. ABSOLUTE MAXIMUM RATINGS All voltages are referenced to GND pin. Rating Symbol Value Unit VCC −0.3 to 19 V High side boot pin voltage VB −0.3 to 720 V High side floating voltage VB−VHB −0.3 to 20 V VHO VHB – 0.3 to VB + 0.3 V Input voltage range High side drive output voltage Low side drive output voltage Allowable hb slew rate Drive input voltage Junction temperature Storage temperature range ESD Capability (Note 1) Human Body Model per JEDEC Standard JESD22−A114E. Charge Device Model per JEDEC Standard JESD22−C101E. VLO −0.3 to VCC + 0.3 V dVHB/dt 50 V/ns VLIN, VHIN −5 to VCC + 0.3 V TJ(MAX) 150° C TSTG −55° to 150° C 4000 1000 Lead Temperature Soldering Reflow (SMD Styles ONLY), Pb−Free Versions (Note 2) 260 V °C Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. This device series incorporates ESD protection and is tested by the following methods. ESD Human Body Model tested per AEC−Q100−002(EIA/JESD22−A114) ESD Charged Device Model tested per AEC−Q100−11(EIA/JESD22−C101E) Latchup Current Maximum Rating: ≤150 mA per JEDEC standard: JESD78 2. For information, please refer to our Soldering and Mounting Techniques Reference Manual, SOLDERRM/D www.onsemi.com 5 NCP51530 Table 4. THERMAL CHARACTERSTICS Rating Symbol Value Unit Thermal Characteristics, SOIC8 (Note 3) Thermal Resistance, Junction to Air (Note 4) RqJA 130 145 °C/W Thermal Characteristics, DFN10 Thermal Resistance, Junction to Air RqJA 45 72 °C/W 3. Refer to ELECTRICAL CHARACTERSTICS and APPLICATION INFORMATION for Safe Operating Area. 4. Values based on copper area of 645 mm2 (or 1 in2) of 1 oz thickness and FR4 PCB substrate. Table 5. RECOMMENDED OPERATING CONDITIONS Rating Input Voltage Range High Side Floating Voltage Symbol Min Max Unit VCC 10 17 V VB−VHB 10 17 V High Side Bridge pin Voltage VHB −1 700 V High Side Output Voltage VHO VHB VB V High Side Output Voltage VLO GND VCC V Input Voltage on LIN and HIN pins VLIN, VHIN GND VCC−2 V TJ −40 125 °C Operating Junction Temperature Range Table 6. ELECTRICAL CHARACTERISTICS (−40°C <TJ < 125°C, VCC =VB =12V, VHB = GND, outputs are not loaded, all voltages are referenced to GND; unless otherwise noted, Typical values are at TJ = 25°C.) Parameters Test Conditions Symbol Min Typ Max Unit SUPPLY SECTION VCC quiescent current VLIN=VHIN=0 ICCQ 0.15 0.25 mA VCC operating current f = 500 kHz, CLOAD = 0 ICCO 2 2.5 mA Boot voltage quiescent current VLIN = VHIN = 0 V IBQ 0.1 0.15 mA Boot voltage operating current f = 500 kHz, CLOAD = 0 IBO 2 2.5 mA HB to GND quiescent current VHS = VHB = 700 V IHBQ 6 11 mA INPUT SECTION Input rising threshold VHIT 2.3 2.7 3.1 V Input falling threshold VLIT 1 1.4 1.8 V Input voltage Hysteresis Input pulldown resistance VIHYS 1.3 V VXIN= 5 V RIN 100 175 250 kW VCC Rising VCCon 8.6 9.1 9.6 V UNDER VOLTAGE LOCKOUT (UVLO) VCC ON VCC hysteresis VB ON VCChys VB Rising VBon VB hysteresis VBhyst High Side Startup Time Time between VB > UVLO & HO Pulse Low level output voltage 1st 0.5 8 8.5 V 9 0.5 V V Tstartup 10 ms ILO = 100 mA VLOL 0.250 V High level output voltage ILO = −100 mA, VLOH = VCC −VLO VLOH 0.270 V Peak source current VLO = 0 V ILOpullup 2.2 A Peak sink current VLO = 12 V ILOpulldown 1.7 A www.onsemi.com 6 NCP51530 Table 6. ELECTRICAL CHARACTERISTICS (−40°C <TJ < 125°C, VCC =VB =12V, VHB = GND, outputs are not loaded, all voltages are referenced to GND; unless otherwise noted, Typical values are at TJ = 25°C.) Parameters Test Conditions Symbol Min Typ Max Unit HO GATE DRIVER Low level output voltage IHO = 100 mA VHOL 0.250 V High level output voltage IHO = −100 mA, VHOH = VHB –VHO VHOH 0.270 V Peak source current VHO = 0 V IHOpullup 2.2 A Peak sink current VHO = 12 V IHOpulldown 1.7 A OUTPUT RISE AND FALL TIME Rise Time LO, HO Cload = 1000 pF TR 8 15 ns Fall Time LO, HO Cload = 1000 pF TF 8 15 ns DELAY MATCHING LI ON, HI OFF Pulse width = 1 ms TMON 7 ns LI OFF, HI ON Pulse width = 1 ms TMOFF 7 ns TIMING VXIN = 5 V , Input pulse width above which output change occurs. TFT VLI falling to VLO falling Cload = 0, Minimum On/Off−time to register as a valid change = 50 ns TDLFF 60 100 ns VHI falling to VHO falling Cload = 0, Minimum On/Off−time to register as a valid change = 50 ns TDHFF 60 100 ns VLI rising to VLO rising Cload = 0, Minimum On/Off−time to register as a valid change = 50 ns TDLRR 60 100 ns VHI rising to VHO rising Cload = 0, Minimum On/Off−time to register as a valid change = 50 ns TDHRR 60 100 ns VLI falling to VLO falling Cload = 0, Minimum On/Off−time to register as a valid change = 50 ns TDLFF 25 40 ns VHI falling to VHO falling Cload = 0, Minimum On/Off−time to register as a valid change = 50 ns TDHFF 25 40 ns VLI rising to VLO rising Cload = 0, Minimum On/Off−time to register as a valid change = 50 ns TDLRR 25 40 ns VHI rising to VHO rising Cload = 0, Minimum On/Off−time to register as a valid change = 50 ns TDHRR 25 40 ns Minimum Input Filter (NCP51530A) 30 40 ns PROPAGATION DELAY NCP51530A PROPAGATION DELAY NCP51530B www.onsemi.com 7 NCP51530 Figure 4. Propagation Delay, Rise and Fall Times Figure 5. Delay Matching www.onsemi.com 8 NCP51530 Figure 6. NCP51530 Operating Currents (No Load, VCC = 12V) Figure 7. NCP51530 Operating Currents (1nF load, VCC = 12V) www.onsemi.com 9 NCP51530 9.7 9.6 9.5 9.3 VCCOFF (V) VCCON (V) 9.4 9.2 9.1 9 8.9 8.8 8.7 8.6 8.5 −40.0 −20.0 0.0 20.0 40.0 60.0 80.0 100.0 120.0 140.0 TEMPERATURE (°C) TEMPERATURE (°C) Figure 9. VCCOFF vs Temperature 1 9.2 9.1 9 0.8 8.9 8.8 0.7 VBON (V) 0.6 0.5 0.4 0.3 8.7 8.6 8.5 8.4 8.3 0.2 8.2 8.1 0.1 0 −40.0 −20.0 0.0 8 −40.0 −20.0 0.0 20.0 40.0 60.0 80.0 100.0 120.0 140.0 TEMPERATURE (°C) Figure 11. VBON vs Temperature 1 0.9 0.8 0.7 VBHyst (V) 8.8 8.7 8.6 8.5 8.4 8.3 8.2 8.1 8 7.9 7.8 7.7 7.6 7.5 7.4 −40.0 −20.0 0.0 20.0 40.0 60.0 80.0 100.0 120.0 140.0 TEMPERATURE (°C) Figure 10. VCCHyst vs Temperature VBOFF (V) 20.0 40.0 60.0 80.0 100.0 120.0 140.0 Figure 8. VCCON vs Temperature 0.9 VHystON (V) 9.2 9.1 9 8.9 8.8 8.7 8.6 8.5 8.4 8.3 8.2 8.1 8 7.9 7.8 −40.0 −20.0 0.0 0.6 0.5 0.4 0.3 0.2 0.1 0 −40.0 −20.0 0.0 20.0 40.0 60.0 80.0 100.0 120.0 140.0 TEMPERATURE (°C) 20.0 40.0 60.0 80.0 100.0 120.0 140.0 TEMPERATURE (°C) Figure 12. VBOff vs Temperature Figure 13. VbHyst vs Temperature www.onsemi.com 10 300 280 260 240 220 200 180 160 140 120 100 80 60 40 20 0 −40.0 −20.0 0.0 20.0 40.0 60.0 80.0 100.0 120.0 140.0 200 180 160 140 IBQ (mA) ICCQ (mA) NCP51530 80 40 20 0 −40.0 −20.0 0.0 20.0 40.0 60.0 80.0 100.0 120.0 140.0 TEMPERATURE (°C) TEMPERATURE (°C) Figure 14. ICCQ vs Temperature Figure 15. IBQ vs Temperature 100 90 12 80 70 10 TDLFF (ns) IHB_LEAK (mA) 100 60 14 8 6 60 50 40 30 4 20 2 10 0 −40.0 −20.0 0.0 20.0 40.0 60.0 80.0 100.0 120.0 140.0 0 −40.0 −20.0 0.0 20.0 40.0 60.0 80.0 100.0 120.0 140.0 TEMPERATURE (°C) TEMPERATURE (°C) Figure 16. IHB_Leakage vs Temperature Figure 17. Low Side Turn on Propagation Delay vs Temperature 100 100 90 90 80 80 70 70 60 TDHFF (ns) TDLRR (ns) 120 50 40 30 60 50 40 30 20 20 10 0 −40.0 −20.0 0.0 10 0 −40.0 −20.0 0.0 20.0 40.0 60.0 80.0 100.0 120.0 140.0 20.0 40.0 60.0 80.0 100.0 120.0 140.0 TEMPERATURE (°C) TEMPERATURE (°C) Figure 18. Low Side Turn on Propagation Delay vs Temperature Figure 19. High Side Turn off Propagation Delay vs Temperature www.onsemi.com 11 NCP51530 100 14 80 12 70 10 60 Tr_LO (ns) TDHRR (ns) 90 50 40 30 8 6 4 20 2 10 0 −40.0 −20.0 0.0 0 −40.0 −20.0 0.0 20.0 40.0 60.0 80.0 100.0 120.0 140.0 TEMPERATURE (°C) TEMPERATURE (°C) Figure 21. Low Side Rise Time vs Temperature 14 14 12 12 10 10 Tf_LO Tr_HO Figure 20. High Side Turn off Propagation Delay vs Temperature 8 6 8 6 4 4 2 2 0 −40.0 −20.0 0.0 20.0 40.0 60.0 80.0 100.0 120.0 140.0 0 −40.0 −20.0 0.0 20.0 40.0 60.0 80.0 100.0 120.0 140.0 20.0 40.0 60.0 80.0 100.0 120.0 140.0 TEMPERATURE (°C) TEMPERATURE (°C) Figure 22. High Side Rise Time vs Temperature Figure 23. Low Side Fall Time vs Temperature 0 NEGATIVE PULSE AMPLITUDE 14 12 Tr_HO 10 8 6 4 2 0 −40.0 −20.0 0.0 −20 −40 −60 −80 −100 −120 0 20.0 40.0 60.0 80.0 100.0 120.0 140.0 100 200 300 400 500 TEMPERATURE (°C) NEGATIVE PULSE WIDTH (ns) Figure 24. High Side Fall Time vs Temperature Figure 25. Typical Safe Operating Area with Negative Transient Voltage on HB Pin www.onsemi.com 12 600 NCP51530 GENERAL DESCRIPTION For popular topologies like LLC, half bridge converters, full bridge converters, two switch forward converter etc. low−side high−side drivers are needed which perform the function of both buffer and level shifter. These devices can drive the gate of the topside MOSFETs whose source node is a dynamically changing node. The bias for the high side driver in these devices is usually provided through a bootstrap circuit. In a bid to make modern power supplies more compact and efficient, power supply designers are increasingly opting for high frequency operations. High frequency operation causes higher losses in the drivers, hence reducing the efficiency of the power supply. NCP51530 is a 700 V high side−low side driver for AC−DC power supplies and inverters. NCP51530 offers best in class propagation delay, low quiescent current and low switching current at high frequencies of operation. This device thus enables highly efficient power supplies operating at high frequencies. NCP51530 is offered in two versions, NCP51530A/B. NCP51530A has a typical 60 ns propagation delay, while NCP51530B has propagation delay of 25 ns. NCP51530 comes in SOIC8 and DFN10 packages. SOIC8 package of the device is pin to pin compatible with industry standard solutions. NCP51530 has two independent input pins HI and LI allowing it to be used in a variety of applications. This device also includes features wherein, in case of floating input, the logic is still defined. Driver inputs are compatible with both CMOS and TTL logic hence it provides easy interface with analog and digital controllers. NCP51530 has under voltage lock out feature for both high and low side drivers which ensures operation at correct VCC and VB voltage levels. The output stage of NCP51530 has 2.2 A/1.7 A current source/sink capability which can effectively charge and discharge a 1 nF load in 15 ns. FEATURES INPUT STAGES NCP51530 has two independent input pins HIN and LIN allowing it to be used in a variety of applications. The input stages of NCP51530 are TTL and CMOS compatible. This ensures that the inputs of NCP51530 can be driven with 3.3 V or 5 V logic signals from analog or digital PWM controllers or logic gates. The input pins have Schmitt triggers to avoid noise induced logic errors. The hysteresis on the input pins is typically 1.3 V. This high value ensures good noise immunity. NCP51530 comes with an important feature wherein outputs (HO, LO) stays low in case any of the input pin is floating. At both the input pins there is an internal pull down resistor to define its logic value in case the pin is left open or NCP51530 is driven by open drain signal. The input logic is explained in the Table 7 below. NCP51530 input pins are also tolerant to negative voltage below the GND pin level as long as it is within the ratings defined in the datasheet. This tolerance allows the use of transformer as an isolation barrier for input pulses. NCP51530A features a noise rejection function to ensure that any pulse glitch shorter than 30 ns will not produce any output. These features are well illustrated in the Figure 28 below. NCP51530B has no such filters in the input stages. The timing diagram NCP51530B is Figure 29 below. www.onsemi.com 13 NCP51530 Table 7. INPUT TABLE www.onsemi.com 14 NCP51530 50ns 80ns 30ns 40ns 10ns LIN/HIN 80ns 60ns 60ns 100ns LO /HO Figure 26. Input Filter (NCP51530A) 50ns 80ns 30ns 10ns LIN/HIN 25ns 30ns 25ns 40ns 80ns 25ns 50ns 10ns Figure 27. No Input Filter (NCP51530B) www.onsemi.com 15 NCP51530 VCCON VCCOFF VCC LIN LO VBON VB − VHB HIN HO Figure 28. UVLO Timing Diagram UNDER VOLTAGE LOCK−OUT If the VCC is below the VCC UVLO voltage, the low side driver output (LO) and high side driver output (HO) both remain low. If VB is below VB UVLO voltage the high side driver output (HO) remains low. However if the VCC is above VCC UVLO voltage level, the low side driver output (LO) can still turn on and off based on the low side driver input (LI) NCP51530 has under voltage lockout protection on both the high side and the low side driver. The function of the UVLO circuits is to ensure that there is enough supply voltages (VCC and VB) to correctly bias high side and low side circuits. This also ensures that the gate of external MOSFETs are driven at an optimum voltage. www.onsemi.com 16 NCP51530 ensures continuous operation in case of a small drop in the bias voltage. This drop in the bias can happen when device starts switching MOSFET and the operating current of the device increases. The UVLO feature of the device is explained in the Figure 30. and is not affected by the VB status. This ensures proper charging of the bootstrap capacitor to bring the high side bias supply VB above UVLO voltage. Both the VCC and VB UVLO circuits are provided with hysteresis feature. This hysteresis feature avoids errors due to ground noise in the power supply. The hysteresis also Figure 29. NCP51530 Turn ON−OFF Paths OUTPUT STAGES side external MOSFETs respectively. When a logic high is received from input stage, Qsource turns on and VCC/VB starts charging Cgs through Rg. Once the Cgs is charged to the drive voltage level the external power MOSFET turns on the external MOSFET to discharge to GND/HB level. When a logic low signal is received from the input stage, Qsource turns off and Qsink turns on providing a path for gate terminal of As seen in the figure, there are parasitic inductances in charging and discharging path of the Cgs. This can result in a little dip in the bias voltages VCC/VB. If the VCC/VB drops below UVLO the power supply can shut down the device. The NCP51530 is equipped with two independent drivers. The output stage of NCP51530 has 1.7 A/2.2 A current source/sink capability which can effectively charge and discharge a 1 nF load in 15 ns. The outputs of NCP51530 can be turned on at the same time and there is no internal dead−time built between them. This allows NCP51530 to be used in topologies like two switch forward converter. The figure below show the output stage structure and the charging and discharging path of the external power MOSFET. The bias supply VCC or VB supply the energy to charge the gate capacitance Cgs of the low side or the top www.onsemi.com 17 NCP51530 Figure 30. Low Side Turn−ON Propagation Delay (NCP51530A) FAST PROPAGATION DELAY Since NCP51530B doesn t have the input filter included, the propagation delay are even faster. NCP51530B offers 30 ns propagation delay between input and output. NCP51530 boasts of industry best propagation delay between input and output. NCP51530A has a typical of 60 ns propagation delay. The best in class propagation delay in NCP51530 makes it suitable for high frequency operation. www.onsemi.com 18 NCP51530 Figure 31. Low Side Turn−Off Propagation Delay (NCP51530A) Figure 32. High Side Turn−Off Propagation Delay (NCP51530B) www.onsemi.com 19 NCP51530 Figure 33. High Side Turn−Off Propagation Delay (NCP51530B) www.onsemi.com 20 NCP51530 Figure 34. Bootstrap Circuit COMPONENT SELECTION It is recommended to use a larger value so as to cover any variations in the gate charge and voltage with temperature. CBOOT CAPACITOR VALUE CALCULATION NCP51530 has two independent drivers for driving high side and low side external MOSFETs. The bias for the high side driver is usually provided through a bootstrap circuit. A typical bootstrap circuit is shown in the figure 8 below. The high side driver is biased by the Cboot (bootstrap capacitor). As can be seen in the circuit, Cboot will charge only when HB goes to GND level. Low value of Cboot can result in a little dip in the bias voltages VB. If the VB drops below UVLO the power supply can shut down the high side driver. Therefore choosing the right value of Cboot is very important for a robust design. An example design for Cboot is given below. Q g + 30 nC, V CC + 15 V Rboot RESISTOR VALUE CALCULATION Rboot resistor value is very important to ensure proper function of the device. A high value of Rboot would slow down the charging of the Cboot while too low a value would push very high charging currents for Cboot. For NCP51530 a value between 2 W and 10 W is recommended for Rboot. For example Rboot = 5 W I boot(pk) + C boot + Q tot V ripple + 30.4 nC 150 mV + 203 nF R boot + 15 V * 1 V 5W + 2.8 A (eq. 5) Where VD is the bootstrap diode forward drop. Thus, Rboot value of 5 W keeps the peak current below 2.8 A. (eq. 1) HIN AND LIN INPUT FILTER Q b + I BQ * t discharge + 81 mC * 5 mS + 405 pC (eq. 2) Q tot + Q g ) Q b + 30 nC ) 405p + 30.4 pC V CC * V D For PWM connection on the LIN and HIN pin of the NCP51530, a RC is recommended to filter high frequency input noise. This filter is particularly important in case of NCP51530B where no internal filter is included. The recommended value for RLIN/RHIN and CHIN/CLIN are as below. (eq. 3) (eq. 4) Qg is equivalent gate charge of the FET IBQ is the boot quiescent current tdishcharge is the discharge time for bootstrap capacitor Vripple is the allowed ripple voltage in the bootstrap capacitor RLIN/RHIN = 100 W CHIN/CLIN = 120 pF www.onsemi.com 21 NCP51530 VCC CAPACITOR SELECTION P operating + V boot * I BO ) V CC * I CCO VCC capacitor value should be selected at least ten times the value of Cboot. In this case thus CVCC > 2 mF. + 14 V * 0.4 mA ) 15 V * 0.4 mA + 11.6 mW IBO is the operating current for the high side driver ICCO is the operating current for the low side driver 2. Power loss of driving external FET (Hard Switching) Rgate SELECTION Rgate are selected to limit the peak gate current during charging and discharging of the gate capacitance. This resistance also helps to damp the ringing due to the parasitic inductances. For example for a Rgate value of 5 W, the peak source and sink currents would be limited to the following values. R gate + 5W I LO_Source + I LO_Sink + R Lgate ) R LOH V CC R Lgate ) R LOL I HO_Source + I HO_Sink + V CC + V CC * V Dboot R Lgate ) R HOH V CC * V Dboot R Lgate ) R HOL + + 6.7 W 15 V 6.8 W + P drivers + Qg is total gate charge of the MOSFET 3. Power loss of driving external FET (Soft Switching) + 2.23 A (eq. 7) 6.7 W ǒǒQgs * VbootǓ ) ǒQgs * VCCǓǓ * f (eq. 13) 4. Level shifting losses (eq. 8) P levelshifting + ǒV r ) V bǓ * Q * f (eq. 14) + 415 V * 1 nC * 100 kHz + 41.5 mW + 2.09 A (eq. 9) 15 V * 1 V 6.8 W P drivers + + ǒǒ4 nC * 14 VǓ ) ǒ4 nC * 15 VǓǓ * 100 kHz + 11 mW + 2.20 A 14 V ǒǒQg * VboostǓ ) ǒQg * VCCǓǓf (eq. 12) + ǒǒ30 nC * 14 VǓ ) ǒ30 nC * 15 VǓǓ * 100 kHz + 87 mW (eq. 6) 15 V (eq. 11) Vr is the rail voltage Q is the substrate charge on the level shifter 5. Total Power Loss (Hard Switching) (eq. 10) + 2.06 A P total + P driver ) P operating ) P levelshifting (eq. 15) + 11.6 mW ) 87 mW ) 40 mW + 138.6 mW TOTAL POWER DISSIPATION Total power dissipation of NCP51530 can be calculated as follows. 1. Static power loss of device (excluding drivers) while switching at an appropriate frequency. 6. Junction temperature increase t J + R qJA * P total + 183 * 0.14 + 25° C www.onsemi.com 22 (eq. 16) NCP51530 LAYOUT RECOMMENDATIONS NCP51530 is a high speed and high current high side and low side driver. To avoid any device malfunction during device operation, it is very important that there is very low parasitic inductance in the current switching path. It is very important that the best layout practices are followed for the PCB layout of the NCP51530. An example layout is shown in the figure below. Some of the layout rules to be followed are listed below. • Keep the low side drive path LO−Q1−GND as small as possible. This reduces the parasitic inductance in the path and hence eliminates ringing on the gate terminal of the low side MOSFET Q1. • Keep the high side drive loop HO−Q2−HB as small as possible. This reduces the parasitic inductance in the • • • path and hence eliminates ringing on the gate terminal of the low side MOSFET Q1. Keep CVCC as near to the VCC pin as possible and the VCC−CVCC−GND loop as small as possible. Keep CVB as near to VB pin as possible and VB−CVB−HB loop as small as possible. Keep the HB−GND−Q1 loop as small as possible. This loop has the potential to produce a negative voltage spike on the HB pin. This negative voltage spike can cause damage to the driver. This negative spike can increase the boot capacitor voltage above the maximum rating and hence cause damage to the driver. Figure 35. Example Layout ORDERING INFORMATION17 Propagation Delay (ns) Input filter Package Shipping† NCP51530ADR2G 60 Yes SOIC−8 (Pb−Free) 2500 / Tape & Reel NCP51530BDR2G 25 No SOIC−8 (Pb−Free) 2500 / Tape & Reel NCP51530AMNTWG 60 Yes DFN10 4x4 (Pb−Free) 4000 / Tape & Reel NCP51530BMNTWG 25 No DFN10 4x4 (Pb−Free) 4000 / Tape & Reel Device †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification Brochure, BRD8011/D. www.onsemi.com 23 NCP51530 PACKAGE DIMENSIONS SOIC−8 NB CASE 751−07 ISSUE AK −X− NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751−01 THRU 751−06 ARE OBSOLETE. NEW STANDARD IS 751−07. A 8 5 S B 0.25 (0.010) M Y M 1 4 −Y− K G C N DIM A B C D G H J K M N S X 45 _ SEATING PLANE −Z− 0.10 (0.004) H D 0.25 (0.010) M Z Y S X S M J SOLDERING FOOTPRINT* 1.52 0.060 7.0 0.275 4.0 0.155 0.6 0.024 1.270 0.050 SCALE 6:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 24 MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0_ 8_ 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0 _ 8 _ 0.010 0.020 0.228 0.244 NCP51530 PACKAGE DIMENSIONS DFN10 4x4, 0.8P CASE 506DJ ISSUE O B A D L PIN ONE REFERENCE 2X ÇÇÇÇ ÇÇÇÇ ÇÇÇÇ ÇÇÇÇ 0.10 C L1 ALTERNATE TERMINAL CONSTRUCTIONS ÉÉ ÉÉ ÇÇ A1 A DETAIL B ALTERNATE A−2 DETAIL A E TOP VIEW 0.10 C L ALTERNATE A−1 0.10 C 2X NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.25 AND 0.30 MM FROM THE TERMINAL TIP. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. 5. FOR DEVICE OPN CONTAINING W OPTION, DETAIL A ALTERNATE CONSTRUCTION A−2 AND DETAIL B ALTERNATE CONSTRUCTION B−2 ARE NOT APPLICABLE. A3 ÉÉÉ ÇÇÇ ÇÇÇ EXPOSED Cu ALTERNATE B−1 MOLD CMPD ALTERNATE B−2 DETAIL B ALTERNATE CONSTRUCTIONS 10X 0.08 C NOTE 4 SIDE VIEW A3 A1 C SEATING PLANE 0.10 C A B DETAIL A 1 D2 10X MILLIMETERS MIN MAX 0.80 1.00 0.00 0.05 0.20 REF 0.25 0.35 4.00 BSC 2.90 3.10 4.00 BSC 1.85 2.05 0.375 BSC 0.80 BSC 0.90 −−− 0.35 0.45 0.00 0.15 RECOMMENDED MOUNTING FOOTPRINT* L 5 3.20 PACKAGE OUTLINE 0.10 C A B E3 DIM A A1 A3 b D D2 E E2 E3 e K L L1 10X 0.60 E2 2.15 0.75 K 10 6 e BOTTOM VIEW 10X 1 b 0.10 C A B 0.05 C 4.30 0.80 PITCH NOTE 3 10X 0.42 DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] ◊ N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 www.onsemi.com 25 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NCP51530/D