ETC2 AP-UM512MD10EG Usb-disk moduleâ ¡ Datasheet

USB-Disk ModuleⅡ
AP-UMxxxxXXXXG-XXXX
RoHS Compliant
USB-Disk ModuleⅡ
Specification
April 23, 2009
Version 1.5
Apacer Technology Inc.
th
th
4 Fl., 75 Xintai 5 Rd., Sec.1, Hsichih, Taipei Hsien 221, Taiwan
Tel: +886-2-2698-2888
Fax: +886-2-2698-2889
www.apacer.com
1
© 2009 Apacer Technology, Inc.
Rev. 1.5
USB-Disk ModuleⅡ
AP-UMxxxxXXXXG-XXXX
FEATURES:
•
USB2.0 High-Speed and USB1.1 FullSpeed compatible interface
•
Capacity
256, 512 MB
1, 2, 4, 8 GB
•
–
–
–
Fast sustained read performance
Sustained read: 30 MB/s
–
Fast sustained write performance
Sustained write: 20 MB/s
•
•
•
•
–
–
1.
2.
–
–
–
–
Support boot-up function for OS
Windows XP Embedded
Windows CE
Linux
1
Windows XP Professional
–
–
–
Temperature ranges
0°C to 70°C for operation (standard)
2
-40°C to 85°C for operation (ET )
-40°C to 100°C for storage
–
–
Low power consumption (typical)
Active mode: 110 mA
Sleep mode: 450 μA
–
Connector
10-pin (2x5) female header
•
Intelligent USB Module
Implements dynamic wear-leveling
algorithms to substantially increase
longevity of flash media
– BCH (6/12 bit) Error Detection Code/Error
Correction Code (EDC/ECC)
– Intrinsic data integrity after power loss
– Wear leveling algorithm that provides more
reliable data storage over an extended
period
•
Support Ready Boost for Windows Vista
•
–
•
•
•
Zero Power Data Retention
Batteries not required for data storage
RoHS Compliant
Extended Data Protection (Optional)
Write protection setting by jumper for
prevention of data overwrites.
Please order NR type. Only support Standard Temperature 2GB, 4GB, 8GB capacity
Extended Temperature
2
© 2009 Apacer Technology, Inc.
Rev. 1.5
USB-Disk ModuleⅡ
AP-UMxxxxXXXXG-XXXX
TABLE OF CONTENTS
1. General Description ..............................................................................4
1.1 Performance-optimized Controller....................................................................................................... 4
1.1.1 Power Management Unit (PMU) ...................................................................................................................4
1.1.2 SRAM Buffer .................................................................................................................................................4
1.1.3 Error Correction Code (ECC) ........................................................................................................................4
1.1.4 Wear-Leveling ...............................................................................................................................................4
1.1.5 Write Protection Mode (Optional) ..................................................................................................................4
2. Functional Block Diagram.....................................................................5
3. Pin Assignment......................................................................................6
3.1 Type A, Type B, Type C, and Type E.................................................................................................. 6
3.2 Type D﹙STD﹚................................................................................................................................... 7
3.3 Type D﹙LP﹚ ..................................................................................................................................... 8
4. Capacity Specifications ........................................................................9
4.1 Functional Specifications..................................................................................................................... 9
4.2 Environmental Specifications .............................................................................................................. 9
5. Electrical Specification ......................................................................10
6. Physical Dimension .............................................................................11
6.1 Horizontal Design .............................................................................................................................. 11
6.1.1 Type A (STD 90D)......................................................................................................................................11
6.1.2 Type B (STD 90D-MH) ...............................................................................................................................12
6.1.3 Type C (STD 90D-MS) ...............................................................................................................................13
6.2 Vertical Design .................................................................................................................................. 14
6.2.1 Type D (STD 180D)....................................................................................................................................14
6.3 Low Profile Design............................................................................................................................. 15
6.3.1 Type D (LP 180D) .......................................................................................................................................15
6.3.2 Type E (LP 90D-MS) ...................................................................................................................................16
7. Product Ordering Information.............................................................17
7.1 Product Code Designation ................................................................................................................ 17
7.2 Valid Combinations............................................................................................................................ 18
7.2.1 Type A
7.2.2 Type B
7.2.3 Type C
7.2.4 Type D
7.2.5 Type D
7.2.6 Type E
(STD 90D)......................................................................................................................................18
(STD 90D-MH) ...............................................................................................................................18
(STD 90D-MS) ...............................................................................................................................18
(STD 180D)....................................................................................................................................19
(LP 180D) ......................................................................................................................................19
(LP 90D-MS) ..................................................................................................................................19
3
© 2009 Apacer Technology, Inc.
Rev. 1.5
USB-Disk ModuleⅡ
AP-UMxxxxXXXXG-XXXX
1. General Description
Apacer’s USB-Disk Module (UDM) is a high performance, embedded solid state drive (SSD) designed to
replace a conventional IDE hard disk drive. UDM SSD can be plugged into a standard Embedded USB
connector commonly found in desktops, portable PC systems and industrial PC systems. This product is
well suited for embedded flash storage applications offering new and expanded functionality as well as
more cost-effective designs, better performance and increased reliability.
1.1 Performance-optimized Controller
The heart of an UDM is the USB controller, which translates standard USB signals into the data and
controls of the flash media. This proprietary USB controller is specifically designed to attain high data
throughput from host to flash.
1.1.1 Power Management Unit (PMU)
The power management unit (PMU) controls the power consumption of the UDM. It can dramatically
extend product battery life by leaving the idle part of the circuitry into sleep mode. The PMU has zero
wake-up latency.
1.1.2 SRAM Buffer
The SRAM buffer is a key contributor to the USB controller performance. It optimizes data writes to the
flash.
1.1.3 Error Correction Code (ECC)
The UDM uses BCH Error Detection Code (EDC) and Error Correction Code (ECC) algorithms which
correct up to 6/12 random single-bit errors for each 512-byte block of data depending on spare area of
flash memory. High performance is achieved through hardware-based error detection and correction.
1.1.4 Wear-Leveling
Flash memory can be erased a limited number of times, This number is called the erase cycle limit, or
write endurance limit, The erase cycle limit applies to each individual erase block in the flash device.
In a typical application, and especially if a file system is used, specific pages are constantly updated (e.g.,
the page that contains the FAT, registry, etc.). Without any special handling, these pages would wear out
more rapidly than other pages, reducing the lifetime of the entire flash.
To overcome this inherent deficiency, Apacer’s USB-Disk Module (UDM) uses wear-leveling algorithm.
This wear-leveling algorithm ensures that consecutive writes of a specific sector are not written physically
to the same page in the flash. This spreads flash media usage evenly across all pages, thereby
maximizing flash lifetime.
The wear-leveling mechanism provides more than 100,000 write/erase cycles for reliable data storage
over an extended period.
1.1.5 Write Protection Mode (Optional)
When the device is configured to the Write-Protection mode, it enhances the data security and protection.
This feature prevents the stored data from inadvertent system writes or erases, and viruses.
4
© 2009 Apacer Technology, Inc.
Rev. 1.5
USB-Disk ModuleⅡ
AP-UMxxxxXXXXG-XXXX
2. Functional Block Diagram
The USB-Disk Module (UDM) contains a controller, embedded firmware, and Flash Media with a female
connector. The UDM interfaces with the host system allowing data to be written to and read from the
Flash Media.
Flash
Media
Host
USB Interface
Flash
Management
Controller
Flash
Media
Figure 2-1: Functional block diagram
5
© 2009 Apacer Technology, Inc.
Rev. 1.5
USB-Disk ModuleⅡ
AP-UMxxxxXXXXG-XXXX
3. Pin Assignment
This chapter provides the information on the pin assignments and signal descriptions.
3.1 Type A, Type B, Type C, and Type E
Table 3-1: Pin Assignment of the 10-pin configuration in Type A, Type B, Type C, and Type E
Pin
Signal
Pin
Signal
1
+5V
2
N.C
3
USB D-
4
N.C
5
USB D+
6
N.C
7
GND
8
N.C
9
Key (Blocked)
10
N.C
6
© 2009 Apacer Technology, Inc.
Rev. 1.5
USB-Disk ModuleⅡ
AP-UMxxxxXXXXG-XXXX
3.2 Type D﹙
﹙STD﹚
﹚
Table 3-2: Pin Assignment of the 10-pin configuration in Type D (STD)
Pin
Signal
Pin
Signal
1
+5V
2
+5V
3
USB D-
4
N.C
5
USB D+
6
N.C
7
GND
8
GND
9
Key (Blocked)
10
GND
7
© 2009 Apacer Technology, Inc.
Rev. 1.5
USB-Disk ModuleⅡ
AP-UMxxxxXXXXG-XXXX
3.3 Type D﹙
﹙LP﹚
﹚
Table 3-3: Pin Assignment of the 10-pin configuration in Type D (LP)
Pin
Signal
Pin
Signal
1
+5V
2
N.C
3
USB D-
4
N.C
5
USB D+
6
N.C
7
GND
8
N.C
9
Key (Blocked)
10
N.C
8
© 2009 Apacer Technology, Inc.
Rev. 1.5
USB-Disk ModuleⅡ
AP-UMxxxxXXXXG-XXXX
4. Capacity Specifications
The USB-Disk Module product family is available as below table matrix.
Table 4-1: Capacity Specification
Density
Total Bytes
256MB
253,739,008
512 MB
511,688,704
1GB
1,027,588,096
2GB
2,059,386,880
4GB
4,118,790,144
8GB
8,237,596,672
4.1 Functional Specifications
Table 4-2: Performance Specifications
USB 2.0 High-Speed (Max.)
Sustained Read
30 MB/sec
Sustained Write
20 MB/sec
4.2 Environmental Specifications
Environmental specification of the USB-Disk Module (UDM) product family which follows the MIL-STD810F standards is available as shown in Table 4-2.
Table 4-2: Environmental Specifications
Temperature
Operation
Storage
0°C to 70°C (standard); -40°C to 85°C (extended temperature)
-40°C to 100°C
Vibration
10 Hz to 500 Hz, 15G, 3 axes, 30 minutes (IEC 68-2-6)
Shock
Duration: 11 ms, 50G, 3 axes, 18 times (IEC 68-2-27)
EMC
FCC, CE
9
© 2009 Apacer Technology, Inc.
Rev. 1.5
USB-Disk ModuleⅡ
AP-UMxxxxXXXXG-XXXX
5. Electrical Specification
Caution: Absolute Maximum Stress Ratings – Applied conditions greater than those listed under
“Absolute Maximum Stress Ratings” may cause permanent damage to the device. This is a stress rating
only and functional operation of the device at these conditions or conditions greater than those defined in
the operational sections of this data sheet is not implied. Exposure to absolute maximum stress rating
conditions may affect device reliability.
Table 5-1: Operating Range
Range
Ambient Temperature
Voltage
Standard
Extended Temperature
0°C to 70°C
-40°C to 85°C
4.5-5.5V
Table 5-2: Absolute maximum power pin stress ratings
Parameter
Power Supply Input
Voltage on any pin except VDD with respect to GND
Symbol
Min
Max
Unit
VDD
VIN
-0.3
-0.3
5.5
5.8
V
V
10
© 2009 Apacer Technology, Inc.
Rev. 1.5
USB-Disk ModuleⅡ
AP-UMxxxxXXXXG-XXXX
6. Physical Dimension
6.1 Horizontal Design
6.1.1 Type A (STD 90D)
Standard 90 degree
Length
28.8mm
Width
26.65mm
Height (Max)
10.5 mm
Unit: mm
Tolerance: ±0.2
11
© 2009 Apacer Technology, Inc.
Rev. 1.5
USB-Disk ModuleⅡ
AP-UMxxxxXXXXG-XXXX
6.1.2 Type B (STD 90D-MH)
Standard 90 Degree Mounting Header
Length
37.8mm
Width
26.65mm
Height (Max)
10.5 mm
Unit: mm
Tolerance: ±0.2
12
© 2009 Apacer Technology, Inc.
Rev. 1.5
USB-Disk ModuleⅡ
AP-UMxxxxXXXXG-XXXX
6.1.3 Type C (STD 90D-MS)
Standard 90 Degree Mounting Screw
Length
37.8mm
Width
26.65mm
Height (Max)
10.5 mm
Unit: mm
Tolerance: ±0.2
13
© 2009 Apacer Technology, Inc.
Rev. 1.5
USB-Disk ModuleⅡ
AP-UMxxxxXXXXG-XXXX
6.2 Vertical Design
6.2.1 Type D (STD 180D)
Standard 180 Degree
Length
37.3mm
Width
26.65mm
Height (Max)
8.5 mm
Unit: mm
Tolerance: ±0.2
14
© 2009 Apacer Technology, Inc.
Rev. 1.5
USB-Disk ModuleⅡ
AP-UMxxxxXXXXG-XXXX
6.3 Low Profile Design
6.3.1 Type D (LP 180D)
Low Profile 180 Degree
Length
31.95mm
Width
24mm
Height (Max)
5 mm
Unit: mm
Tolerance: ±0.2
15
© 2009 Apacer Technology, Inc.
Rev. 1.5
USB-Disk ModuleⅡ
AP-UMxxxxXXXXG-XXXX
6.3.2 Type E (LP 90D-MS)
Low Profile 90 Degree Mounting Screw
Length
Write Protect
36.8mm
Width
26.5mm
Height (Max)
7.5 mm
Read/Write
Unit: mm
Tolerance: ±0.2
16
© 2009 Apacer Technology, Inc.
Rev. 1.5
USB-Disk ModuleⅡ
AP-UMxxxxXXXXG-XXXX
7. Product Ordering Information
7.1 Product Code Designation
AP – U M xxxx X X X
X G – XX XX
Option:
RB: Ready Boost
WP: Write Protection
NR: Non-Removable
MH: Mounting Header
MS: Mounting Screw
RoHS Compliant
Temperature:
C: Commercial Temperature
E: Extended Temperature
PCB version
Diemension
1 = 90D STD
2 = 180D STD
3 = 90D Low Profile
4 = 180D Low Profile
Solution version
Capacity
256M = 256MB
512M = 512MB
001G = 1GB
002G = 2GB
004G = 4GB
008G = 8GB
Model Name
Apacer Product Code
17
© 2009 Apacer Technology, Inc.
Rev. 1.5
USB-Disk ModuleⅡ
AP-UMxxxxXXXXG-XXXX
7.2 Valid Combinations
7.2.1 Type A (STD 90D)
Standard 90 degree
Capacity
Standard
Extended Temperature
256MB
AP-UM256ME10CG
AP-UM256MD10EG
512MB
AP-UM512ME10CG
AP-UM512MD10EG
1GB
AP-UM001GE10CG
AP-UM001GD10EG
2GB
AP-UM002GE10CG
AP-UM002GD10EG
4GB
AP-UM004GE10CG
AP-UM004GD10EG
8GB
AP-UM008GE10CG
AP-UM008GD10EG
7.2.2 Type B (STD 90D-MH)
Standard 90 Degree Mounting Header
Capacity
Standard
Extended Temperature
256MB
AP-UM256ME10CG-MH
AP-UM256MD10EG-MH
512MB
AP-UM512ME10CG-MH
AP-UM512MD10EG-MH
1GB
AP-UM001GE10CG-MH
AP-UM001GD10EG-MH
2GB
AP-UM002GE10CG-MH
AP-UM002GD10EG-MH
4GB
AP-UM004GE10CG-MH
AP-UM004GD10EG-MH
8GB
AP-UM008GE10CG-MH
AP-UM008GD10EG-MH
7.2.3 Type C (STD 90D-MS)
Standard 90 Degree Mounting Screw
Capacity
Standard
Extended Temperature
256MB
AP-UM256ME10CG-MS
AP-UM256MD10EG-MS
512MB
AP-UM512ME10CG-MS
AP-UM512MD10EG-MS
1GB
AP-UM001GE10CG-MS
AP-UM001GD10EG-MS
2GB
AP-UM002GE10CG-MS
AP-UM002GD10EG-MS
4GB
AP-UM004GE10CG-MS
AP-UM004GD10EG-MS
8GB
AP-UM008GE10CG-MS
AP-UM008GD10EG-MS
18
© 2009 Apacer Technology, Inc.
Rev. 1.5
USB-Disk ModuleⅡ
AP-UMxxxxXXXXG-XXXX
7.2.4 Type D (STD 180D)
Standard 180 Degree
Capacity
Standard
Extended Temperature
256MB
AP-UM256ME20CG
AP-UM256MD20EG
512MB
AP-UM512ME20CG
AP-UM512MD20EG
1GB
AP-UM001GE20CG
AP-UM001GD20EG
2GB
AP-UM002GE20CG
AP-UM002GD20EG
4GB
AP-UM004GE20CG
AP-UM004GD20EG
8GB
AP-UM008GE20CG
AP-UM008GD20EG
7.2.5 Type D (LP 180D)
Low Profile 180 Degree
Capacity
Standard
Extended Temperature
256MB
AP-UM256ME40CG
AP-UM256MD40EG
512MB
AP-UM512ME40CG
AP-UM512MD40EG
1GB
AP-UM001GE40CG
AP-UM001GD40EG
2GB
AP-UM002GE40CG
AP-UM002GD40EG
4GB
AP-UM004GE40CG
AP-UM004GD40EG
8GB
AP-UM008GE40CG
AP-UM008GD40EG
7.2.6 Type E (LP 90D-MS)
Low Profile 90 Degree Mounting Screw
Capacity
Standard
Extended Temperature
256MB
AP-UM256ME31CG-MS
AP-UM256MD31EG-MS
512MB
AP-UM512ME31CG-MS
AP-UM512MD31EG-MS
1GB
AP-UM001GE31CG-MS
AP-UM001GD31EG-MS
2GB
AP-UM002GE31CG-MS
AP-UM002GD31EG-MS
4GB
AP-UM004GE31CG-MS
AP-UM004GD31EG-MS
8GB
AP-UM008GE31CG-MS
AP-UM008GD31EG-MS
Note: Valid combinations are those products in mass production or will be in mass production. Consult
your Apacer sales representative to confirm availability of valid combinations and to determine availability
of new combinations.
19
© 2009 Apacer Technology, Inc.
Rev. 1.5
USB-Disk ModuleⅡ
AP-UMxxxxXXXXG-XXXX
Revision History
Revision
Description
Date
1.0
Official Release
May 5, 2008
1.1
Product Ordering Information Updated
September 30, 2008
1.2
Pin Assignment Updated
December 17, 2008
1.3
Type E dimension & ECC capability updated
March 18, 2009
1.4
Feature Context & Product Ordering Information updated
April 21, 2009
1.5
Type D (LP 180D) drawing updated
April 23, 2009
20
© 2009 Apacer Technology, Inc.
Rev. 1.5
USB-Disk ModuleⅡ
AP-UMxxxxXXXXG-XXXX
Global Presence
Taiwan (Headquarters)
Apacer Technology Inc.
th
th
4 Fl., 75 Xintai 5 Rd., Sec.1
Hsichih, Taipei Hsien 221
Taiwan, R.O.C.
Tel: +886-2-2698-2888
Fax: +886-2-2698-2889
[email protected]
U.S.A.
Apacer Memory America, Inc.
386 Fairview Way, Suite102,
Milpitas, CA 95035
Tel: 1-408-586-1291
Fax: 1-408-935-9611
[email protected]
Japan
Apacer Technology Corp.
5F, Matsura Bldg., Shiba, Minato-Ku
Tokyo, 105-0014, Japan
Tel: 81-3-5419-2668
Fax: 81-3-5419-0018
[email protected]
Europe
Apacer Technology B.V.
Europalaan 89
5232 BC 'S-Hertogenbosch
The Netherlands
Tel: 31-73-645-9620
Fax: 31-73-645-9629
[email protected]
China
Apacer Electronic (Shanghai) Co., Ltd
1301, No.251,Xiaomuqiao Road, Shanghai,
200032, China
Tel: 86-21-5529-0222
Fax: 86-21-5206-6939
[email protected]
India
Apacer Technologies Pvt. Ltd.
#143, 1st Floor, Raheja Arcade,
5th Block Kormangala Industrial Layout,
Bangalore - 560095, India
Tel: 91-80-4152-9061
[email protected]
21
© 2009 Apacer Technology, Inc.
Rev. 1.5
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Apacer:
AP-UM001GD10EG-MH AP-UM001GD10EG-MS AP-UM001GD31EG-MS AP-UM002GD10EG-MH APUM002GD31EG-MS AP-UM004GD10EG-MH AP-UM004GD10EG-MS AP-UM004GD31EG-MS AP-UM008GD10EGMH AP-UM008GD10EG-MS AP-UM008GD31EG-MS AP-UM256MD10EG-MH AP-UM256MD10EG-MS APUM256MD31EG-MS AP-UM512MD10EG-MH AP-UM512MD10EG-MS AP-UM512MD31EG-MS
Similar pages