AD ADM809SAKSZ-REEL Microprocessor supervisory circuits in 3-lead sc70 and sot-23 Datasheet

Microprocessor Supervisory Circuits
in 3-Lead SC70 and SOT-23
ADM803/ADM809/ADM810
Data Sheet
FEATURES
FUNCTIONAL BLOCK DIAGRAMS
Specified over temperature
Low power consumption: 17 μA
Precision voltage monitor: 2.5 V, 3 V, 3.3 V, 5 V options
Reset assertion down to 1 V VCC
140 ms minimum power-on reset
Open-drain RESET output (ADM803)
Push-pull RESET output (ADM809)
Push-pull RESET output (ADM810)
SC70 and SOT-23 packages
ADM803
VCC
RESET
GENERATOR
240ms
VREF
RESET
GND
ADM809/ADM810
APPLICATIONS
Microprocessor systems
Computers
Controllers
Intelligent instruments
RESET
GENERATOR
240ms
VCC
VREF
RESET
(RESET)
GND
VCC
*RPULL-UP
VCC
MICROPROCESSOR
SYSTEM
RESET
INPUT
RESET
GND
GND
*ADM803 ONLY
03736-001
VCC
ADM803/ADM809
Figure 1.
GENERAL DESCRIPTION
The ADM803/ADM809/ADM810 supervisory circuits monitor
the power supply voltage in microprocessor systems. They
provide a reset output during power-up, power-down, and
brownout conditions. On power-up, an internal timer holds
reset asserted for 240 ms. This holds the microprocessor in a
reset state until conditions have stabilized. The reset output
remains operational with VCC as low as 1 V. The ADM803 and
ADM809 provide an active low reset signal (RESET), whereas
the ADM810 provides an active high signal (RESET) output.
The ADM809 and ADM810 have push-pull outputs, whereas
the ADM803 has an open-drain output, which requires an
external pull-up resistor.
Rev. I
Seven reset threshold voltage options are available, suitable for
monitoring a variety of supply voltages (see Table 3).
The reset comparator features built-in glitch immunity, making
it immune to fast transients on VCC.
The ADM803/ADM809/ADM810 consume only 17 μA, making
them suitable for low power, portable equipment. The ADM803
is available in a 3-lead SC70; the ADM809/ADM810 are available
in 3-lead SOT-23 and 3-lead SC70 packages.
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©1997–2014 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
ADM803/ADM809/ADM810
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Pin Configurations and Function Descriptions ............................5
Applications ....................................................................................... 1
Typical Performance Characteristics ..............................................6
Functional Block Diagrams ............................................................. 1
Interfacing to Other Devices ............................................................8
General Description ......................................................................... 1
Ensuring a Valid Reset Output Down to VCC = 0 V .................8
Revision History ............................................................................... 2
Benefits of an Accurate Reset Threshold ...................................8
Specifications..................................................................................... 3
Interfacing to Microprocessors with Multiple Interrupts ........8
Absolute Maximum Ratings............................................................ 4
Outline Dimensions ..........................................................................9
ESD Caution .................................................................................. 4
Ordering Guide .......................................................................... 10
REVISION HISTORY
10/14—Rev. H to Rev. I
Changes to Applications Section .................................................... 1
Changes to Table 2 ............................................................................ 4
Updated Outline Dimensions ......................................................... 9
Changes to Ordering Guide .......................................................... 10
8/08—Rev. G to Rev. H
Added Figure 4; Renumbered Sequentially .................................. 5
Changes to Figure 8 .......................................................................... 6
Updated Outline Dimensions ......................................................... 9
Changes to Ordering Guide .......................................................... 10
9/06—Rev. F to Rev. G
Updated Outline Dimensions ......................................................... 9
Changes to Ordering Guide ............................................................ 9
6/05—Rev. E to Rev. F.
Changes to Ordering Guide ............................................................ 4
Updated Outline Dimensions ......................................................... 9
2/05—Rev. D to Rev. E.
Changes to Ordering Guide ............................................................ 4
2/05—Rev. C to Rev. D.
Changes to Ordering Guide ............................................................ 4
Updated Outline Dimensions ......................................................... 8
5/03—Rev. B to Rev. C.
Added ADM803 ................................................................. Universal
Changes to Features ..........................................................................1
Changes to General Description .....................................................1
Changes to Figure 1...........................................................................1
Changes to Specifications .................................................................2
Changes to Table I .............................................................................3
Updated Ordering Guide .................................................................4
1/03—Rev. A to Rev. B.
Changes to Specifications .................................................................2
Changes to Table I .............................................................................3
Changes to Ordering Guide .............................................................4
Changes to TPCs 1–3, and TPC 7 ...................................................5
Updated Outline Dimensions ..........................................................7
10/02—Rev. 0 to Rev. A.
Addition of SC70 package ................................................. Universal
Change to General Description .......................................................1
Changes to Specifications .................................................................2
Changes to Absolute Maximum Ratings ........................................3
Change to Table I ...............................................................................3
Change to Ordering Guide ...............................................................4
Change to TPC 1 ...............................................................................5
Updated Outline Dimensions ..........................................................7
4/97—Revision 0: Initial Version
Rev. I | Page 2 of 11
Data Sheet
ADM803/ADM809/ADM810
SPECIFICATIONS
VCC = full operating range, TA = TMIN to TMAX, VCC typical = 5 V for L/M/J models, 3.3 V for T/S models, 3 V for R models, and 2.5 V for
Z models, unless otherwise noted.
Table 1.
Parameter
VCC OPERATING VOLTAGE RANGE
Min
1.0
1.2
Supply Current
RESET VOLTAGE THRESHOLD
ADM8xxL
ADM8xxM
ADM8xxJ
ADM8xxT
ADM8xxS
ADM8xxR
ADM8xxZ
RESET THRESHOLD TEMPERATURE COEFFICIENT
VCC to Reset Delay
RESET ACTIVE TIMEOUT PERIOD
Typ
24
17
4.56
4.50
4.44
4.31
4.25
4.20
3.93
3.89
3.80
3.04
3.00
2.95
2.89
2.85
2.81
2.59
2.55
2.52
2.28
2.25
2.22
140
100
RESET OUTPUT VOLTAGE LOW (ADM803/ADM809)
4.63
4.38
4.00
3.08
2.93
2.63
2.32
30
20
240
Max
5.5
5.5
35
30
60
60
Unit
V
V
μA
μA
μA
μA
Test Conditions/Comments
TA = 0°C to 70°C
TA = −40°C to +125°C
VCC < 5.5 V, ADM8xxL/M/J, TA = −40°C to +85°C
VCC < 3.6 V, ADM8xxR/S/T/Z, TA = −40°C to +85°C
VCC < 5.5 V, ADM8xxL/M/J, TA = 85°C to 125°C
VCC < 3.6 V, ADM8xxR/S/T/Z, TA = 85°C to 125° C
4.70
4.75
4.82
4.45
4.50
4.56
4.06
4.10
4.20
3.11
3.15
3.21
2.96
3.00
3.05
2.66
2.70
2.74
2.35
2.38
2.42
TA = 25°C
TA = −40°C to +85°C
TA = −40°C to +125°C
TA = 25°C
TA = −40°C to +85°C
TA = −40°C to +125°C
TA = 25°C (ADM809/ADM810 only)
TA = −40°C to +85°C (ADM809/ADM810 only)
TA = −40°C to +125°C (ADM809/ADM810 only)
TA = 25°C
TA = −40°C to +85°C
TA = −40°C to +125°C
TA = 25°C
TA = −40°C to +85°C
TA = −40°C to +125°C
TA = 25°C
TA = −40°C to +85°C
TA = −40°C to +125°C
TA = 25°C
TA = −40°C to +85°C
TA = −40°C to +125°C
460
840
0.3
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
ppm/°C
μs
ms
ms
V
0.4
V
0.3
V
VCC = VTH to (VTH − 100 mV)
TA = −40°C to +85°C
TA = 85°C to 125°C
VCC = VTH min, ISINK = 1.2 mA, ADM803R/S/T/Z,
ADM809R/S/T/Z
VCC = VTH min, ISINK = 3.2 mA, ADM803L/M/J,
ADM809L/M/J
VCC > 1.0 V, ISINK = 50 μA
V
V
VCC > VTH max, ISOURCE = 500 μA, ADM809R/S/T/Z
VCC > VTH max, ISOURCE = 800 μA, ADM809L/M/J
V
V
VCC = VTH min, ISINK = 1.2 mA, ADM810R/S/T/Z
VCC = VTH min, ISINK = 3.2 mA, ADM810L/M/J
V
1.8 V < VCC < VTH min, ISOURCE = 150 μA
μA
VCC > VTH, RESET deasserted
RESET OUTPUT VOLTAGE HIGH (ADM809)
0.8 VCC
VCC − 1.5
RESET OUTPUT VOLTAGE LOW (ADM810)
0.3
0.4
RESET OUTPUT VOLTAGE HIGH (ADM810)
0.8 VCC
RESET OPEN-DRAIN OUTPUT
Leakage Current (ADM803)
1
Rev. I | Page 3 of 11
ADM803/ADM809/ADM810
Data Sheet
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 3. Reset Threshold Options
Table 2.
RESET Model
ADM8xxL
ADM8xxM
ADM8xxJ (ADM809/ADM810 Only)
ADM8xxT
ADM8xxS
ADM8xxR
ADM8xxZ
Ratings
−0.3 V to +6 V
−0.3 V to VCC + 0.5 V
−0.3 V to +6.0 V
20 mA
20 mA
100 V/μs
VCC
146°C/W
270°C/W
300°C
215°C
220°C
−65°C to +150°C
RESET
VREF
VREF
VREF
t1
t1
t1 = RESET TIME = 240ms TYP
VREF = RESET VOLTAGE THRESHOLD
Figure 2. Power Fail Reset Timing
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
ESD CAUTION
Rev. I | Page 4 of 11
VREF
03736-003
Parameter
VCC
RESET, RESET (Push-Pull)
RESET (Open-Drain)
Input Current
VCC
Output Current
RESET, RESET
Rate of Rise, VCC
θJA Thermal Impedance
SC70
SOT-23
Lead Temperature (Soldering, 10 sec)
Vapor Phase (60 sec)
Infrared (15 sec)
Storage Temperature Range
Threshold (V)
4.63
4.38
4.00
3.08
2.93
2.63
2.32
Data Sheet
ADM803/ADM809/ADM810
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
ADM803/
ADM809/
RESET 2
ADM810
3 VCC
TOP VIEW
(Not to Scale)
RESET 2
03736-102
3 VCC
TOP VIEW
(Not to Scale)
GND 1
03736-002
GND 1
Figure 4. ADM810 Pin Configuration
Figure 3. ADM803/ADM809 Pin Configuration
Table 4. Pin Function Descriptions
Pin No.
ADM803/ADM809
1
N/A
ADM810
1
2
Mnemonic
GND
RESET
2
N/A
RESET
3
3
VCC
Description
Ground Reference for All Signals; 0 V.
Active High Logic Output. RESET remains high while VCC is below the reset threshold
and remains high for 240 ms (typical) after VCC rises above the reset threshold.
Active Low Logic Output. RESET remains low while VCC is below the reset threshold
and remains low for 240 ms (typical) after VCC rises above the reset threshold.
Supply Voltage Being Monitored.
Rev. I | Page 5 of 11
ADM803/ADM809/ADM810
Data Sheet
TYPICAL PERFORMANCE CHARACTERISTICS
30
240.0
20
POWER-UP RESET TIMEOUT (ms)
SUPPLY CURRENT (µA)
239.5
VCC = 5V
25
VCC = 3V
15
10
5
239.0
238.5
238.0
237.5
237.0
236.5
236.0
–20
0
20
40
TEMPERATURE (°C)
60
80 85
235.0
–40
03736-004
0
–40
Figure 5. Supply Current vs. Temperature (No Load)
200
–20
0
20
40
TEMPERATURE (°C)
60
80 85
03736-007
235.5
Figure 8. Power-Up Reset Timeout vs. Temperature, ADM8xxR
1.0020
VOD = VTH – VCC
180
POWER-DOWN RESET (µs)
NORMALIZED RESET THRESHOLD
VOD = 10mV
160
140
120
VOD = 20mV
100
80
60
40
VOD = 100mV
1.0015
1.0010
1.0005
1.0000
0.9995
VOD = 200mV
–20
0
20
40
TEMPERATURE (°C)
60
80 85
0.9990
–40
03736-005
0
–40
Figure 6. Power-Down Reset Delay vs. Temperature, ADM8xxL/M/J
180
0
20
40
TEMPERATURE (°C)
60
80 85
Figure 9. Normalized Reset Voltage Threshold vs. Temperature
VOD = VTH – VCC
160
SUPPLY VOLTAGE
5V p-p
VOD = 10mV
140
120
T
VOD = 20mV
100
RESET OUTPUT
VOLTAGE
1
80
ADM809T
ADM809R
60
40
VOD = 100mV
T
2
20
VOD = 200mV
–20
0
20
40
TEMPERATURE (°C)
60
80 85
03736-006
0
–40
CH1
2.00V
CH2
2.00V
M 200ms
CH1
2.00V
Figure 10. Reset Output Voltage vs. Supply Voltage
Figure 7. Power-Down Reset Delay vs. Temperature, ADM8xxT/S/R/Z
Rev. I | Page 6 of 11
03736-009
POWER-DOWN RESET (µs)
–20
03736-008
20
Data Sheet
ADM803/ADM809/ADM810
350
300
250
200
150
ADM8xxL/M/J
100
ADM8xxR/S/T/Z
50
0
1
10
100
RESET COMPARATOR OVERDRIVE, VTH – VCC (mV)
1000
03736-010
MAXIMUM TRANSIENT DURATION (µs)
400
Figure 11. Maximum Transient Duration Without Causing a Reset Pulse vs.
Reset Comparator Overdrive
Rev. I | Page 7 of 11
ADM803/ADM809/ADM810
Data Sheet
INTERFACING TO OTHER DEVICES
The ADM803/ADM809/ADM810 series is designed to integrate
with as many devices as possible and, therefore, has a standard
output dependent on VCC. This enables the parts to be used in
both 3 V and 5 V, or any nominal voltage within the minimum
and maximum specifications for VCC. This design simplifies
interfacing the ADM803/ADM809/ADM810 to other devices.
ENSURING A VALID RESET OUTPUT DOWN TO
VCC = 0 V
When VCC falls below 0.8 V, the ADM803/ADM809 RESET no
longer sinks current. A high impedance CMOS logic input
connected to RESET may, therefore, drift to undetermined logic
levels. To eliminate this problem, a 100 kΩ resistor should be
connected from RESET to ground.
VCC
ADM803/ADM809/ADM810, the possibility of a malfunction
during a power failure is greatly reduced because the devices
can operate effectively even when there are large degradations
of the supply voltages. Another advantage is the very accurate
internal voltage reference circuit of the ADM803/ADM809/
ADM810. These benefits combine to produce an exceptionally
reliable voltage monitor circuit.
INTERFACING TO MICROPROCESSORS WITH
MULTIPLE INTERRUPTS
In a number of cases, it is necessary to interface many interrupts
from different devices (for example, thermal, altitude, and
velocity sensors). The ADM803/ADM809/ADM810 can easily
be integrated into existing interrupt-handling circuits, as shown
in Figure 13, or can be used as standalone devices.
VCC
PRIORITY ENCODER
74LS147
4-LINE BCD TO
MICROPROCESSOR
ADM809
VCC
RESET
VCC
ADM809
GND
03736-011
RESET
OTHER SENSING
DEVICES
Figure 12. Ensuring a Valid Reset Output Down to VCC = 0 V
GND
03736-012
BENEFITS OF AN ACCURATE RESET THRESHOLD
In other microprocessors, tolerances in supply voltages lead
to an overall increase in reset tolerance levels due to the
deterioration of the reset circuit’s power supply. In the
Figure 13. Interfacing to Microprocessors with Multiple Interrupts
Rev. I | Page 8 of 11
Data Sheet
ADM803/ADM809/ADM810
OUTLINE DIMENSIONS
3.04
2.90
2.80
1.40
1.30
1.20
3
2.64
2.10
1
2
0.60
0.45
1.03
0.89
2.05
1.78
1.02
0.95
0.88
1.12
0.89
0.100
0.013
GAUGE
PLANE
0.54
REF
0.180
0.085
0.25
0.60 MAX
0.30 MIN
011909-C
0.51
0.37
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS TO-236-AB
Figure 14. 3-Lead Small Outline Transistor Package [SOT-23-3]
(RT-3)
Dimensions shown in millimeters
2.20
2.00
1.80
1.35
1.25
1.15
3
2
1
2.40
2.10
1.80
0.65 BSC
1.10
0.80
0.10 MAX
COPLANARITY
0.10
0.40
0.25
SEATING
PLANE
0.40
0.10
0.26
0.10
ALL DIMENSIONS COMPLIANT WITH EIAJ SC70
Figure 15. 3-Lead Thin Shrink Small Outline Transistor Package [SC70]
(KS-3)
Dimensions shown in millimeters
Rev. I | Page 9 of 11
0.30
0.20
0.10
072809-A
1.00
0.80
ADM803/ADM809/ADM810
Data Sheet
ORDERING GUIDE
Model 1
ADM803LAKSZ-REEL
ADM803LAKSZ-REEL7
ADM803MAKS-REEL7
ADM803MAKSZ-REEL7
ADM803RAKSZ-REEL7
ADM803SAKS-REEL7
ADM803SAKSZ-REEL
ADM803SAKSZ-REEL7
ADM803TAKS-REEL7
ADM803TAKSZ-REEL7
ADM803ZAKSZ-REEL7
ADM809JAKS-REEL7
ADM809JAKSZ-REEL
ADM809JAKSZ-REEL7
ADM809JARTZ-REEL7
ADM809LAKS-REEL7
ADM809LAKSZ-REEL
ADM809LAKSZ-REEL7
ADM809LART-REEL7
ADM809LARTZ-REEL
ADM809LARTZ-REEL7
ADM809MAKS-REEL7
ADM809MAKSZ-REEL
ADM809MAKSZ-REEL7
ADM809MART-REEL7
ADM809MARTZ-REEL
ADM809MARTZ-REEL7
ADM809RAKS-REEL
ADM809RAKS-REEL7
ADM809RAKSZ-REEL
ADM809RAKSZ-REEL7
ADM809RART-REEL
ADM809RART-REEL7
ADM809RARTZ-REEL
ADM809RARTZ-REEL7
ADM809SAKS-REEL
ADM809SAKS-REEL7
ADM809SAKSZ-REEL
ADM809SAKSZ-REEL7
ADM809SART-REEL7
ADM809SARTZ-REEL
ADM809SARTZ-REEL7
ADM809TAKS-REEL7
ADM809TAKSZ-REEL
ADM809TAKSZ-REEL7
ADM809TART-REEL7
ADM809TARTZ-REEL
ADM809TARTZ-REEL7
ADM809ZAKS-REEL
ADM809ZAKS-REEL7
ADM809ZAKSZ-REEL
Reset Threshold (V)
4.63
4.63
4.38
4.38
2.63
2.93
2.93
2.93
3.08
3.08
2.32
4.00
4.00
4.00
4.00
4.63
4.63
4.63
4.63
4.63
4.63
4.38
4.38
4.38
4.38
4.38
4.38
2.63
2.63
2.63
2.63
2.63
2.63
2.63
2.63
2.93
2.93
2.93
2.93
2.93
2.93
2.93
3.08
3.08
3.08
3.08
3.08
3.08
2.32
2.32
2.32
Temperature Range
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
Rev. I | Page 10 of 11
Branding 2, 3
M6L
M6L
M03
M6J
M6M
M06
M50
M50
M05
M4M
M6N
M9C or 9JXX
M6P
M6P
M6P
M9A
M6R
M6R
9LXX
9LXX
9LXX
M9B
M51
M51
9MXX
M51
M51
M9F
M9F
M4D
M4D
9RXX
9RXX
M4D
M4D
M9E
M9E
M53
M53
9SXX
M53
M53
M9D
M4K
M4K
9TXX
9TXX
9TXX
M9G
M9G
M4P
Quantity
10,000
3,000
3,000
3,000
3,000
3,000
10,000
3,000
3,000
3,000
3,000
3,000
10,000
3,000
3,000
3,000
10,000
3,000
3,000
10,000
3,000
3,000
10,000
3,000
3,000
10,000
3,000
10,000
3,000
10,000
3,000
10,000
3,000
10,000
3,000
10,000
3,000
10,000
3,000
3,000
10,000
3,000
3,000
10,000
3,000
3,000
10,000
3,000
10,000
3,000
10,000
Package
Description
3-Lead SC70
3-Lead SC70
3-Lead SC70
3-Lead SC70
3-Lead SC70
3-Lead SC70
3-Lead SC70
3-Lead SC70
3-Lead SC70
3-Lead SC70
3-Lead SC70
3-Lead SC70
3-Lead SC70
3-Lead SC70
3-Lead SOT-23
3-Lead SC70
3-Lead SC70
3-Lead SC70
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SC70
3-Lead SC70
3-Lead SC70
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SC70
3-Lead SC70
3-Lead SC70
3-Lead SC70
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SC70
3-Lead SC70
3-Lead SC70
3-Lead SC70
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SC70
3-Lead SC70
3-Lead SC70
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SC70
3-Lead SC70
3-Lead SC70
Package
Option
KS-3
KS-3
KS-3
KS-3
KS-3
KS-3
KS-3
KS-3
KS-3
KS-3
KS-3
KS-3
KS-3
KS-3
RT-3
KS-3
KS-3
KS-3
RT-3
RT-3
RT-3
KS-3
KS-3
KS-3
RT-3
RT-3
RT-3
KS-3
KS-3
KS-3
KS-3
RT-3
RT-3
RT-3
RT-3
KS-3
KS-3
KS-3
KS-3
RT-3
RT-3
RT-3
KS-3
KS-3
KS-3
RT-3
RT-3
RT-3
KS-3
KS-3
KS-3
Data Sheet
Model 1
ADM809ZAKSZ-REEL7
ADM809ZART-REEL
ADM809ZARTZ-REEL
ADM809ZARTZ-REEL7
ADM810JAKSZ-REEL7
ADM810JARTZ-REEL7
ADM810LAKSZ-REEL7
ADM810LARTZ-REEL
ADM810LARTZ-REEL7
ADM810MAKSZ-REEL7
ADM810MARTZ-REEL7
ADM810RAKSZ-REEL7
ADM810RARTZ-REEL7
ADM810SAKSZ-REEL7
ADM810SARTZ-REEL7
ADM810TAKSZ-REEL7
ADM810TARTZ-REEL7
ADM810ZAKSZ-REEL7
ADM810ZARTZ-REEL7
ADM803/ADM809/ADM810
Reset Threshold (V)
2.32
2.32
2.32
2.32
4.00
4.00
4.63
4.63
4.63
4.38
4.38
2.63
2.63
2.93
2.93
3.08
3.08
2.32
2.32
Temperature Range
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
Z = RoHS Compliant Part.
XX = Date code, may be top or bottom marked.
3
RoHS compliant part has XX branded on the bottom of the device.
1
2
©1997–2014 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D03736-0-10/14(I)
Rev. I | Page 11 of 11
Branding 2, 3
M4P
9ZXX
M4P
M4P
M6V
M6V
M6W or ALXX
M6W or ALXX
M6W or ALXX
M6S
M6S
M52 or ARXX
M52 or ARXX
M6T
M6T
M4V
M4V
M6U
M6U
Quantity
3,000
10,000
10,000
3,000
3,000
3,000
3,000
10,000
3,000
3,000
3,000
3,000
3,000
3,000
3,000
3,000
3,000
3,000
3,000
Package
Description
3-Lead SC70
3-Lead SOT-23
3-Lead SOT-23
3-Lead SOT-23
3-Lead SC70
3-Lead SOT-23
3-Lead SC70
3-Lead SOT-23
3-Lead SOT-23
3-Lead SC70
3-Lead SOT-23
3-Lead SC70
3-Lead SOT-23
3-Lead SC70
3-Lead SOT-23
3-Lead SC70
3-Lead SOT-23
3-Lead SC70
3-Lead SOT-23
Package
Option
KS-3
RT-3
RT-3
RT-3
KS-3
RT-3
KS-3
RT-3
RT-3
KS-3
RT-3
KS-3
RT-3
KS-3
RT-3
KS-3
RT-3
KS-3
RT-3
Similar pages