Finisar FTLF1619P1XCL 2 gb/s rohs compliant long-wavelength pluggable sfp transceiver Datasheet

Finisar
Product Specification
2 Gb/s RoHS Compliant Long-Wavelength Pluggable SFP Transceiver
FTLF1619P1xCL
PRODUCT FEATURES
•
Up to 2.125Gb/s bi-directional
data links
•
Hot-pluggable SFP footprint
•
Built-in digital diagnostic functions
•
Uncooled 1550nm DFB laser
transmitter
•
APD Receiver
•
Duplex LC connector
•
Very low jitter
•
Metal enclosure, for lower EMI
•
Single 3.3V power supply
•
Low power dissipation <700mW
typical
•
Extended operating temperature
range: -10°C to 70°C
APPLICATIONS
•
Gigabit Ethernet
•
1X and 2X Fibre Channel
Finisar’s FTLF1619P1xCL Small Form Factor Pluggable (SFP) transceivers are
compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA)1.
They simultaneously comply with Gigabit Ethernet as specified in IEEE Std 802.32, and
1x and 2x Fibre Channel as defined in FC-PI-2 Rev. 10.03,4. They are RoHS compliant
and lead-free per Directive 2002/95/EC5 and Finisar Application Note AN-2038. Digital
diagnostics functions are available via the 2-wire serial bus specified in the SFP MSA.
PRODUCT SELECTION
FTLF1619P1xCL
x
W
B
© Finisar Corporation March 30, 2006 Rev A
Wide Extraction Bail
Narrow Extraction Bail
Page 1
FTLF1619P1xCL Pluggable SFP Product Specification – March 2006
I.
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Finisar
Pin Descriptions
Symbol
VEET
TFAULT
TDIS
MOD_DEF(2)
MOD_DEF(1)
MOD_DEF(0)
Rate Select
LOS
VEER
VEER
VEER
RDRD+
VEER
VCCR
VCCT
VEET
TD+
TDVEET
Name/Description
Transmitter Ground (Common with Receiver Ground)
Transmitter Fault. Not supported.
Transmitter Disable. Laser output disabled on high or open.
Module Definition 2. Data line for Serial ID.
Module Definition 1. Clock line for Serial ID.
Module Definition 0. Grounded within the module.
No connection required
Loss of Signal indication. Logic 0 indicates normal operation.
Receiver Ground (Common with Transmitter Ground)
Receiver Ground (Common with Transmitter Ground)
Receiver Ground (Common with Transmitter Ground)
Receiver Inverted DATA out. AC Coupled
Receiver Non-inverted DATA out. AC Coupled
Receiver Ground (Common with Transmitter Ground)
Receiver Power Supply
Transmitter Power Supply
Transmitter Ground (Common with Receiver Ground)
Transmitter Non-Inverted DATA in. AC Coupled.
Transmitter Inverted DATA in. AC Coupled.
Transmitter Ground (Common with Receiver Ground)
Ref.
1
2
3
3
3
4
5
1
1
1
1
1
1
Notes:
1. Circuit ground is internally isolated from chassis ground.
2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.
3. Should be pulled up with 4.7k – 10kohms on host board to a voltage between 2.0V and 3.6V.
MOD_DEF(0) pulls line low to indicate module is plugged in.
4. Finisar FTLFxx21xxxxx transceivers operate between OC-3 and OC-48, 1x and 2x Fibre Channel, and
Gigabit Ethernet data rates and respective protocols without active control. Finisar FTLFxx19xxxxx
transceivers operate at 1x and 2x Fibre Channel, and Gigabit Ethernet data rates and respective
protocols without active control.
5. LOS is open collector output. Should be pulled up with 4.7k – 10kohms on host board to a voltage
between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.
Towards
Bezel
1
VeeT
2
TXFault
3
TX Disable
4
MOD-DEF(2)
5
MOD-DEF(1)
6
MOD-DEF(0)
7
Rate Select
8
LOS
9
VeeR
10
VeeR
VeeT
20
TD-
19
TD+
18
VeeT
17
VccT
16
VccR
15
VeeR
14
RD+
13
RD-
12
VeeR
11
Towards
ASIC
Diagram of Connector Block Pinout on the Host Board
© Finisar Corporation March 30, 2006 Rev A
Page 2
FTLF1619P1xCL Pluggable SFP Product Specification – March 2006
II.
Absolute Maximum Ratings
Parameter
Maximum Supply Voltage
Storage Temperature
Case Operating Temperature
Relative Humidity
III.
Finisar
Symbol
Vcc
TS
TOP
RH
Min
-0.5
-40
-10
0
Typ
Max
4.5
85
70
85
Unit
V
°C
°C
%
Ref.
1
Electrical Characteristics (TOP = -10 to 70 °C, VCC = 3.00 to 3.60 Volts)
Parameter
Supply Voltage
Supply Current
Transmitter
Input differential impedance
Single ended data input swing
Transmit Disable Voltage
Transmit Enable Voltage
Transmit Disable Assert Time
Receiver
Single ended data output swing
Data output rise time
Data output fall time
LOS Fault
LOS Normal
Power Supply Rejection
Deterministic Jitter Contribution
Total Jitter Contribution
Symbol
Vcc
Icc
Rin
Vin,pp
VD
VEN
Vout,pp
tr
tf
VLOS fault
VLOS norm
PSR
RX Δ DJ
RX Δ TJ
Min
3.00
Typ
230
Max
3.60
300
Unit
V
mA
Ref.
Ω
mV
V
V
us
2
1200
Vcc
Vee+ 0.8
10
mV
ps
ps
V
V
mVpp
ps
ps
4
5
5
6
6
7
8
100
250
Vcc – 1.3
Vee
300
Vcc – 0.5
Vee
100
400
100
100
800
175
175
VccHOST
Vee+0.5
51.7
122.4
3
Notes:
1. Non Condensing.
2. Connected directly to TX data input pins. AC coupled thereafter.
3. Or open circuit.
4. Into 100 ohms differential termination.
5. 20 – 80 %
6. Loss Of Signal is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected.
7. Receiver sensitivity is compliant with power supply sinusoidal modulation of 20 Hz to 1.5 MHz up to
specified value applied through the recommended power supply filtering network.
8. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ
and Δ DJ.
© Finisar Corporation March 30, 2006 Rev A
Page 3
FTLF1619P1xCL Pluggable SFP Product Specification – March 2006
IV.
Finisar
Optical Characteristics (TOP = -10 to 70°C, VCC = 3.00 to 3.60 Volts)
Parameter
Transmitter
Output Opt. Pwr: 9/125 SMF
Optical Wavelength
Spectral Width (-20dB)
Optical Extinction Ratio
Optical Modulation Amplitude
Sidemode Supression ratio
Optical Rise/Fall Time
Relative Intensity Noise
Deterministic Jitter Contribution
Total Jitter Contribution
Receiver
Average Rx Sensitivity @ 2.125
Gb/s (2X Fibre Channel)
Average Rx Sensitivity @ 1.25 Gb/s
(Gigabit Ethernet)
Average Rx Sensitivity @ 1.062
Gb/s (1X Fibre Channel)
Maximum Input Power
Optical Center Wavelength
LOS De-Assert
LOS Assert
LOS Hysteresis
Symbol
Min
POUT
λ
σ
ER
OMA
SSRmin
tr/ tf
RIN
RX Δ DJ
RX Δ TJ
0
1540
Max
Unit
+5
1570
1
180
-120
51.7
122.4
dBm
nm
nm
dB
μW
dB
ps
dB/Hz
ps
ps
RSENS1
-28
dBm
5, 6
RSENS2
-30
dBm
5, 6
RSENS1
-30
dBm
5, 6
PMAX
λC
LOSD
LOSA
Typ
9
174
30
-9
1270
-41
0.5
1600
-28
Ref.
1
2
3
4
dBm
nm
dBm
dBm
dB
Notes:
1. Class 1 Laser Safety per FDA/CDRH and EN (IEC) 60825 regulations.
2. Equivalent extinction ratio specification for Fibre Channel. Allows smaller ER at higher average
power.
3. Unfiltered, 20-80%. Complies with IEEE 802.3 (Gig. E), FC 1x and 2x eye masks when filtered.
4. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ
and Δ DJ.
5. Measured with conformance signals defined in FC-PI-2 Rev. 10.0 specifications.
6. Measured with PRBS 27-1 at 10-12 BER
© Finisar Corporation March 30, 2006 Rev A
Page 4
FTLF1619P1xCL Pluggable SFP Product Specification – March 2006
V.
Finisar
General Specifications
Parameter
Data Rate
Bit Error Rate
Max. Supported Link Length on
9/125μm SMF @ 2X Fibre Channel
Max. Supported Link Length on
9/125μm SMF @ 1X Fibre Channel
or Gigabit Ethernet
Symbol
BR
BER
LMAX2
Min
1062
LMAX3
Typ
Max
2125
10-12
Units
Mb/s
Ref.
104
km
1
2
3
112
km
3
Notes:
1. Gigabit Ethernet and 1x/2x Fibre Channel compliant.
2. Tested with a PRBS 27-1 test pattern.
3. Attenuation of 0.25 dB/km is used for the link length calculations. Distances are indicative only. A
2dB penalty is included for dispersion on >2Gb/s data rates. Please refer to the Optical Specifications
in Table IV to calculate a more accurate link budget based on specific conditions in your application.
VI.
Environmental Specifications
Finisar SFP transceivers have an extended operating temperature range from -10°C to
+70°C case temperature.
Parameter
Case Operating Temperature
Storage Temperature
VII.
Symbol
Top
Tsto
Min
-10
-40
Typ
Max
70
85
Units
°C
°C
Ref.
Regulatory Compliance
Finisar transceivers are Class 1 Laser Products and comply with US FDA regulations.
These products are certified by TÜV and CSA to meet the Class 1 eye safety
requirements of EN (IEC) 60825 and the electrical safety requirements of
EN (IEC) 60950. Copies of certificates are available at Finisar Corporation upon request.
© Finisar Corporation March 30, 2006 Rev A
Page 5
FTLF1619P1xCL Pluggable SFP Product Specification – March 2006
Finisar
VIII. Digital Diagnostic Functions
Finisar FTLF1619P1xCL SFP transceivers support the 2-wire serial communication
protocol as defined in the SFP MSA1. It is very closely related to the E2PROM defined in
the GBIC standard, with the same electrical specifications.
The standard SFP serial ID provides access to identification information that describes
the transceiver’s capabilities, standard interfaces, manufacturer, and other information.
Additionally, Finisar SFP transceivers provide a unique enhanced digital diagnostic
monitoring interface, which allows real-time access to device operating parameters such
as transceiver temperature, laser bias current, transmitted optical power, received optical
power and transceiver supply voltage. It also defines a sophisticated system of alarm and
warning flags, which alerts end-users when particular operating parameters are outside of
a factory set normal range.
The SFP MSA defines a 256-byte memory map in E2PROM that is accessible over a
2-wire serial interface at the 8 bit address 1010000X (A0h). The digital diagnostic
monitoring interface makes use of the 8 bit address 1010001X (A2h), so the originally
defined serial ID memory map remains unchanged. The interface is identical to, and is
thus fully backward compatible with both the GBIC Specification and the SFP Multi
Source Agreement. The complete interface is described in Finisar Application Note AN2030: “Digital Diagnostics Monitoring Interface for SFP Optical Transceivers”.
The operating and diagnostics information is monitored and reported by a Digital
Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed
through a 2-wire serial interface. When the serial protocol is activated, the serial clock
signal (SCL, Mod Def 1) is generated by the host. The positive edge clocks data into the
SFP transceiver into those segments of the E2PROM that are not write-protected. The
negative edge clocks data from the SFP transceiver. The serial data signal (SDA, Mod
Def 2) is bi-directional for serial data transfer. The host uses SDA in conjunction with
SCL to mark the start and end of serial protocol activation. The memories are organized
as a series of 8-bit data words that can be addressed individually or sequentially.
For more information, please see the SFP MSA documentation1 or Finisar Application
Note AN-2030.
Digital diagnostics for the FTLF1619P1xCL are externally calibrated by default.
Please note that evaluation board FDB-1018 is available with Finisar ModDEMO
software that allows simple to use communication over the 2-wire serial interface.
© Finisar Corporation March 30, 2006 Rev A
Page 6
FTLF1619P1xCL Pluggable SFP Product Specification – March 2006
IX.
Finisar
Mechanical Specifications
Finisar’s Small Form Factor Pluggable (SFP) transceivers are compatible with the
dimensions defined by the SFP Multi-Sourcing Agreement (MSA) 3.
FTLF1619P1BCL
© Finisar Corporation March 30, 2006 Rev A
Page 7
FTLF1619P1xCL Pluggable SFP Product Specification – March 2006
Finisar
FTLF1619P1WCL
© Finisar Corporation March 30, 2006 Rev A
Page 8
FTLF1619P1xCL Pluggable SFP Product Specification – March 2006
X.
Finisar
PCB Layout and Bezel Recommendations
© Finisar Corporation March 30, 2006 Rev A
Page 9
FTLF1619P1xCL Pluggable SFP Product Specification – March 2006
© Finisar Corporation March 30, 2006 Rev A
Finisar
Page 10
FTLF1619P1xCL Pluggable SFP Product Specification – March 2006
Finisar
XI.
References
1.
Small Form Factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA),
September 2000. Documentation is currently available at Finisar upon request.
2.
IEEE Std 802.3. IEEE Standards Department, 2002.
3.
“Fibre Channel Draft Physical Interface Specification (FC-PI-2 Rev. 10.0)”.
American National Standard for Information Systems.(*)
4.
“Fibre Channel Physical and Signaling Interface (FC-PH, FC-PH2, FC-PH3)”.
American National Standard for Information Systems.
5.
Directive 2002/95/EC of the European Council Parliament and of the Council,
“on the restriction of the use of certain hazardous substances in electrical and
electronic equipment.” January 27, 2003.
(*)
FC-PI-2 Rev. 10.0 does not specify a 1550nm DFB interface for extended reach
applications. The FTLF1519P1xCL complies with this standard, except for the optical
output power. See section IV for details.
XII.
For More Information
Finisar Corporation
1308 Moffett Park Drive
Sunnyvale, CA 94089-1133
Tel. 1-408-548-1000
Fax 1-408-541-6138
[email protected]
www.finisar.com
© Finisar Corporation March 30, 2006 Rev A
Page 11
Similar pages