LINER LTC2857HMS-1 20mbps and slew rate limited 15kv rs485/rs422 transceiver Datasheet

LTC2856-1/LTC2856-2
LTC2857-1/LTC2857-2
LTC2858-1/LTC2858-2
20Mbps and Slew Rate
Limited 15kV RS485/RS422
Transceivers
DESCRIPTION
FEATURES
■
■
■
■
■
■
■
■
■
■
■
20Mbps or Low EMI 250kbps Maximum Data Rate
No Damage or Latchup to ESD: ±15kV HBM
High Input Impedance Supports 256 Nodes
(C, I-Grade)
Operation Up to 125°C (H-Grade)
Guaranteed Failsafe Receiver Operation Over the
Entire Common Mode Range
Current Limited Drivers and Thermal Shutdown
Delayed Micropower Shutdown: 5μA Maximum
(C, I-Grade)
Power Up/Down Glitch-Free Driver Outputs
Low Operating Current: 900μA Maximum in Receive
Mode
Compatible with TIA/EIA-485-A Specifications
Available in 8-Lead and 10-Lead 3mm × 3mm DFN
and 8-Lead and 10-Lead MSOP Packages
APPLICATIONS
■
■
■
Low Power RS485/RS422 Transceiver
Level Translator
Backplane Transceiver
, LT, LTC and LTM are registered trademarks of Linear Technology Corporation.
All other trademarks are the property of their respective owners.
The LTC®2856-1, LTC2856-2, LTC2857-1, LTC2857-2,
LTC2858-1 and LTC2858-2 are low power, RS485/RS422
transceivers operating on 5V supplies at maximum data
rates of 20Mbps or 250kbps for low EMI. The receiver has
a one-eighth unit load, supporting up to 256 nodes per
bus (C, I-Grade), and a failsafe feature that guarantees a
high output state under conditions of floating or shorted
inputs.
The driver maintains a high output impedance over the
entire common mode range when disabled or when the
supply is removed. Excessive power dissipation caused by
bus contention or a fault is prevented by current limiting
all outputs and by thermal shutdown.
Enhanced ESD protection allows these parts to withstand
±15kV (human body model) on the transceiver interface
pins without latchup or damage.
PART
NUMBER
MAX DATA
RATE (Mbps)
DUPLEX
PACKAGE
LTC2856-1
20
Half
MSOP-8, DFN-8
LTC2856-2
0.25
Half
MSOP-8, DFN-8
LTC2857-1
20
Full
MSOP-8, DFN-8
LTC2857-2
0.25
Full
MSOP-8, DFN-8
LTC2858-1
20
Full
MSOP-10, DFN-10
LTC2858-2
0.25
Full
MSOP-10, DFN-10
TYPICAL APPLICATION
LTC2858-1 at 20Mbps
LTC2856-1
RO1
RE1
R
VCC1
DE1
D
Y
GND1
Z
2V/DIV
DI1
DI
RT
LTC2856-1
RO2
RE2
R
VCC2
Y-Z
RT
DE2
DI2
D
GND2
285678 TA01a
20ns/DIV
2856 TA01b
285678fe
1
LTC2856-1/LTC2856-2
LTC2857-1/LTC2857-2
LTC2858-1/LTC2858-2
ABSOLUTE MAXIMUM RATINGS
(Note 1)
Supply Voltage (VCC) ................................... –0.3V to 7V
Logic Input Voltages (RE, DE, DI) ................ –0.3V to 7V
Interface I/O (A, B, Y, Z) ....................(VCC – 15V) to 15V
Receiver Output Voltage (RO) .......–0.3V to (VCC + 0.3V)
Operating Temperature Range (Note 4)
LTC285xC ................................................ 0°C to 70°C
LTC285xI.............................................. –40°C to 85°C
LTC285xH .......................................... –40°C to 125°C
Storage Temperature Range
MSOP ................................................ –65°C to 150°C
DFN.................................................... –65°C to 150°C
Lead Temperature (Soldering, 10 sec)
MSOP ............................................................... 300°C
PACKAGE INFORMATION
LTC2856
TOP VIEW
RO 1
RE 2
DE 3
9
DI 4
8
VCC
7
B
6
A
5
GND
TOP VIEW
RO
RE
DE
DI
8
7
6
5
1
2
3
4
VCC
B
A
GND
MS8 PACKAGE
8-LEAD PLASTIC MSOP
DD PACKAGE
8-LEAD (3mm s 3mm) PLASTIC DFN
TJMAX = 150°C, θJA = 200°C/W, θJC = 40°C/W
EXPOSED PAD (PIN 9) IS GND, MUST BE SOLDERED TO PCB
TJMAX = 150°C, θJA = 43°C/W, θJC = 3°C/W
LTC2857
TOP VIEW
VCC 1
RO 2
DI 3
9
GND 4
8
A
7
B
6
Z
5
Y
TOP VIEW
VCC
RO
DI
GND
8
7
6
5
1
2
3
4
A
B
Z
Y
MS8 PACKAGE
8-LEAD PLASTIC MSOP
DD PACKAGE
8-LEAD (3mm s 3mm) PLASTIC DFN
TJMAX = 150°C, θJA = 200°C/W, θJC = 40°C/W
EXPOSED PAD (PIN 9) IS GND, MUST BE SOLDERED TO PCB
TJMAX = 150°C, θJA = 43°C/W, θJC = 3°C/W
LTC2858
TOP VIEW
RO
1
10 VCC
RE
2
9 A
11
DE
3
DI
4
7 Z
GND
5
6 Y
8 B
DD PACKAGE
10-LEAD (3mm s 3mm) PLASTIC DFN
TOP VIEW
RO
RE
DE
DI
GND
1
2
3
4
5
10
9
8
7
6
VCC
A
B
Z
Y
MS PACKAGE
10-LEAD PLASTIC MSOP
TJMAX = 150°C, θJA = 120°C/W, θJC = 45°C/W
EXPOSED PAD (PIN 11) IS GND, MUST BE SOLDERED TO PCB
TJMAX = 150°C, θJA = 43°C/W, θJC = 3°C/W
285678fe
2
LTC2856-1/LTC2856-2
LTC2857-1/LTC2857-2
LTC2858-1/LTC2858-2
ORDER INFORMATION
LTC2856 C
DD
-1
#TR PBF
LEAD FREE DESIGNATOR
TAPE AND REEL
TR = Tape and Reel
SPEED
-1 = 20Mbps Max. Data Rate
-2 = 250kbps Max. Data Rate
PACKAGE TYPE
DD = 8-Lead Plastic DFN (LTC2856, LTC2858)
MS8 = 8-Lead Plastic MSOP (LTC2856, LTC2857)
MS = 10-Lead Plastic MSOP (LTC2858)
TEMPERATURE GRADE
C = Commercial Temperature Range (0°C to 70°C)
I = Industrial Temperature Range (–40°C to 85°C)
H = Automotive Temperature Range (–40°C to 125°C)
PRODUCT PART NUMBER
LTC2856 = Half Duplex, with Enables
LTC2857 = Full Duplex, no Enables
LTC2858 = Full Duplex, with Enables
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
PRODUCT SELECTION GUIDE
PART NUMBER
PART MARKING
MAX DATA RATE (Mbps)
DUPLEX
LOW POWER
SHUTDOWN MODE
PACKAGE
LTC2856-1
LTCMF, LCMG
20
Half
Yes
MSOP-8, DFN-8
LTC2856-2
LTCMH, LCMJ
0.25
Half
Yes
MSOP-8, DFN-8
LTC2857-1
LTCMC, LCMD
20
Full
No
MSOP-8, DFN-8
LTC2857-2
LTCMK, LCMM
0.25
Full
No
MSOP-8, DFN-8
LTC2858-1
LTCGQ, LCGR
20
Full
Yes
MSOP-10, DFN-10
LTC2858-2
LTCMQ, LCMR
0.25
Full
Yes
MSOP-10, DFN-10
285678fe
3
LTC2856-1/LTC2856-2
LTC2857-1/LTC2857-2
LTC2858-1/LTC2858-2
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VCC = 5V unless otherwise noted. (Note 2)
SYMBOL
PARAMETER
CONDITIONS
MIN
Differential Driver Output Voltage
R = ∞, VCC = 4.5V (Figure 1)
●
R = 27Ω (RS485), VCC = 4.5V (Figure 1)
●
R = 50Ω (RS422), VCC = 4.5V (Figure 1)
●
Change in Magnitude of Driver Differential
Output Voltage for Complementary Output
States
Driver Common Mode Output Voltage
R = 27Ω or R = 50Ω (Figure 1)
Change in Magnitude of Driver Common Mode
Output Voltage for Complementary Output
States
Driver Three-State (High Impedance) Output
Current on Y and Z
Maximum Driver Short-Circuit Current
TYP
MAX
UNITS
VCC
V
1.5
VCC
V
2
VCC
V
●
0.2
V
R = 27Ω or R = 50Ω (Figure 1)
●
3
V
R = 27Ω or R = 50Ω (Figure 1)
●
0.2
V
DE = 0V, (Y or Z) = –7V, 12V, LTC2858-1,
LTC2858-2
–7V ≤ (Y or Z) ≤ 12V (Figure 2)
●
±10
μA
±250
mA
●
125
μA
Driver
|VOD|
Δ|VOD|
VOC
Δ|VOC|
IOZD
IOSD
●
±120
Receiver
VTH
Receiver Differential Input Threshold Voltage
DE = TE = 0V, VCC = 0V or 5V, VIN = 12V
(Figure 3) (C, I-Grade)
DE = TE = 0V, VCC = 0V or 5V, VIN = –7V,
(Figure 3) (C, I-Grade)
DE = TE = 0V, VCC = 0V or 5V, VIN = 12V
(Figure 3) (H-Grade)
DE = TE = 0V, VCC = 0V or 5V, VIN = –7V,
(Figure 3) (H-Grade)
RE = VCC or 0V, DE = TE = 0V,
VIN = –7V, –3V, 3V, 7V, 12V (Figure 3)
(C, I-Grade)
RE = VCC or 0V, DE = TE = 0V,
VIN = –7V, –3V, 3V, 7V, 12V (Figure 3)
(H-Grade)
–7V ≤ B ≤ 12V
ΔVTH
Receiver Input Hysteresis
B = 0V
VOH
Receiver Output High Voltage
I(RO) = –4mA, A-B = 200mV, VCC = 4.5V
●
VOL
Receiver Output Low Voltage
I(RO) = 4mA, A-B = –200mV, VCC = 4.5V
●
0.4
V
Receiver Three-State (High Impedance) Output
Current on RO
RE = 5V, 0V ≤ RO ≤ VCC, LTC2856-1,
LTC2856-2, LTC2858-1, LTC2858-2
●
±1
μA
VIH
Logic Input High Voltage
DE, DI, RE, VCC = 5.5V
●
VIL
Logic Input Low Voltage
DE, DI, RE, VCC = 4.5V
●
IINL
Logic Input Current
DE, DI, RE
●
Supply Current in Shutdown Mode
DE = 0V, RE = VCC,
LTC2856, LTC2858 (C and I-Grade)
LTC2856, LTC2858 (H-Grade)
No Load, DE = 0V, RE = 0V, LTC2856-1,
LTC2856-2, LTC2858-1, LTC2858-2
IIN
RIN
IOZR
Receiver Input Current (A, B)
Receiver Input Resistance
●
–100
μA
●
250
μA
●
–145
●
96
125
kΩ
●
48
125
kΩ
μA
●
±0.2
25
V
mV
2.4
V
Logic
2
V
0.8
V
0
±10
μA
●
0
5
μA
●
0
540
15
900
μA
μA
Supplies
ICCS
ICCR
Supply Current in Receive Mode
●
285678fe
4
LTC2856-1/LTC2856-2
LTC2857-1/LTC2857-2
LTC2858-1/LTC2858-2
SWITCHING CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VCC = 5V unless otherwise noted. (Note 2)
SYMBOL
PARAMETER
CONDITIONS
ICCT
Supply Current in Transmit Mode
No Load, DE = VCC,
RE = VCC
ICCTR
Supply Current with Both Driver and Receiver
Enabled
No Load, DE = VCC,
RE = 0V
MIN
LTC2856-1
LTC2858-1
LTC2856-2
LTC2858-2
LTC2856-1
LTC2857-1
LTC2858-1
LTC2856-2
LTC2857-2
LTC2858-2
TYP
MAX
UNITS
●
630
1000
μA
●
670
1100
μA
●
660
1100
μA
●
700
1200
μA
Driver in LTC2856-1, LTC2857-1, LTC2858-1
fMAX
Maximum Data Rate
(Note 3)
●
tPLHD, tPHLD
Driver Input to Output
RDIFF = 54Ω, CL = 100pF (Figure 4)
●
10
50
ns
ΔtPD
Driver Input to Output Difference |tPLHD – tPHLD| RDIFF = 54Ω, CL = 100pF (Figure 4)
●
1
6
ns
tSKEWD
Driver Output Y to Output Z
RDIFF = 54Ω, CL = 100pF (Figure 4)
●
1
±6
ns
tRD, tFD
Driver Rise or Fall Time
RDIFF = 54Ω, CL = 100pF (Figure 4)
●
4
12.5
ns
tZLD, tZHD,
tLZD, tHZD
Driver Enable or Disable Time
RL = 500Ω, CL = 50pF, RE = 0V,
LTC2856-1, LTC2858-1 (Figure 5)
●
70
ns
tZHSD, tZLSD
Driver Enable from Shutdown
RL = 500Ω, CL = 50pF, RE = VCC,
LTC2856-1, LTC2858-1 (Figure 5)
●
8
μs
tSHDN
Time to Shutdown
(DE = ↓, RE = VCC) or (DE = 0V, RE = ↑),
LTC2856-1, LTC2858-1 (Figure 5)
●
100
ns
(Note 3)
●
RDIFF = 54Ω, CL = 100pF (Figure 4)
●
ΔtPDS
Driver Input to Output Difference |tPLHD – tPHLD| RDIFF = 54Ω, CL = 100pF (Figure 4)
●
tSKEWDS
Driver Output A to Output B
RDIFF = 54Ω, CL = 100pF (Figure 4)
●
tRDS, tFDS
Driver Rise or Fall Time
RDIFF = 54Ω, CL = 100pF (Figure 4)
●
0.90
tZHDS, tZLDS
Driver Enable Time
RL = 500Ω, CL = 50pF, RE = 0V,
LTC2856-2, LTC2858-2 (Figure 5)
tLZDS, tHZDS
Driver Disable Time
20
Mbps
Driver in LTC2856-2, LTC2857-2, LTC2858-2
fMAXS
Maximum Data Rate
tPLHDS, tPHLDS Driver Input to Output
250
kbps
0.95
1.5
μs
50
500
ns
200
±500
ns
1.5
μs
●
300
ns
RL = 500Ω, CL = 50pF, RE = 0V,
LTC2856-2, LTC2858-2 (Figure 5)
●
70
ns
tZHSDS, tZLSDS Driver Enable from Shutdown
RL = 500Ω, CL 50pF, RE = VCC,
LTC2856-2, LTC2858-2 (Figure 5)
●
8
μs
tSHDNS
Time to Shutdown
(DE = 0V, RE↑) or (DE = ↓, RE = VCC),
LTC2856-2, LTC2858-2 (Figure 5)
●
500
ns
tPLHR, tPHLR
Receiver Input to Output
●
50
70
ns
Receiver
tSKEWR
Differential Receiver Skew, |tPLHR – tPHLR|
CL = 15pF, VCM = 1.5V, |VAB| = 1.5V,
tR and tF < 4ns (Figure 6)
CL = 15pF (Figure 6)
●
1
6
ns
tRR, tFR
Receiver Output Rise or Fall Time
CL = 15pF (Figure 6)
●
3
12.5
ns
tZLR, tZHR,
tLZR, tHZR
Receiver Enable/Disable
●
50
ns
tZHSR, tZLSR
Receiver Enable from Shutdown
RL = 1k, CL = 15pF, DE = VCC,
LTC2856-1, LTC2856-2, LTC2858-1,
LTC2858-2 (Figure 7)
RL = 1k, CL = 15pF, DE = 0V,
LTC2856-1, LTC2856-2, LTC2858-1,
LTC2858-2 (Figure 7)
●
8
μs
285678fe
5
LTC2856-1/LTC2856-2
LTC2857-1/LTC2857-2
LTC2858-1/LTC2858-2
ELECTRICAL CHARACTERISTICS
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime. High temperatures degrade operating lifetimes.
Operating lifetime is derated at temperatures greater than 105°C.
Note 2: All currents into device pins are positive; all currents out of device
pins are negative. All voltages are referenced to device ground unless
otherwise specified.
Note 3: Maximum data rate is guaranteed by other measured parameters
and is not tested directly.
Note 4: This IC includes overtemperature protection that is intended
to protect the device during momentary overload conditions.
Overtemperature protection actives at a junction temperature exceeding
150°C. Continuous operation above the specified maximum operating
junction temperature may result in device degradation or failure.
TEST CIRCUITS
Y
GND
OR
VCC
DI
Y
+
DRIVER
R
GND
OR
VCC
VOD
–
Z
R
+
–
DI
IOSD
DRIVER
VOC
Z
285678 F01
–7V TO +12V
285678 F02
Figure 1. Driver DC Characteristics
Figure 2. Driver Output Short-Circuit Current
IIN
VIN
+
–
+
–
A OR B
RECEIVER
B OR A
285678 F03
V
RIN = IN
IIN
Figure 3. Receiver Input Current and Input Resistance
285678fe
6
LTC2856-1/LTC2856-2
LTC2857-1/LTC2857-2
LTC2858-1/LTC2858-2
TEST CIRCUITS
VCC
Y
DI
tPHLD,
tPHLDS
tPLHD,
tPLHDS
DI
0V
tSKEWD,tSKEWDS
CL
DRIVER
RDIFF
Y, Z
VO
1/2 VO
CL
Z
90%
285678 F04a
Y-Z
10%
90%
0
0
10%
285678 F04b
tRD,
tRDS
tFD,
tFDS
Figure 4. Driver Timing Measurement
VCC
RL
Y
VCC
OR
GND
DI
CL
GND
OR
VCC
DRIVER
DE
1/2 VCC
0V
VCC
tZLD,
tZLDS,
tZLSD,
tZLSDS
VO
Y OR Z
tLZD,
tLZDS
1/2 VCC
0.5V
VOL
RL
DE
Z
CL
VCC
OR
GND
285678 F05a
VOH
0.5V
1/2 VCC
Z OR Y
0V
tZHD,
tZHDS,
tZHSD,
tZHSDS
tHZD,
tHZDS,
tSHDN,
tSHDNS
285678 F05b
Figure 5. Driver Enable and Disable Timing Measurement
285678fe
7
LTC2856-1/LTC2856-2
LTC2857-1/LTC2857-2
LTC2858-1/LTC2858-2
TEST CIRCUITS
VAB
A-B
–VAB
A
±VAB/2
VCM
RECEIVER
RO
B
±VAB/2
0
tPLHR
VCC
VO
RO
CL
0
90%
1/2 VCC
10%
tPHLR
90%
10%
1/2 VCC
tRR
285678 F06
tFR
285678 F06b
tSKEWR = tPLHR – tPHLR
Figure 6. Receiver Propagation Delay Measurements
VCC
RE
0V OR VCC
RECEIVER
VCC OR 0V
1/2 VCC
0V
A
B
RE
RL
RO
CL
VCC
OR
GND
tZLR,
tZLSR
VCC
VO
RO
tLZR
1/2 VCC
0.5V
VOL
VOH
0.5V
1/2 VCC
RO
DI = 0V OR VCC
0V
285678 F07a
285678 F05b
tZHR,
tZHSR
tHZR
Figure 7. Receiver Enable/Disable Time Measurements
FUNCTION TABLES
LTC2856-1, LTC2856-2
LTC2858-1, LTC2858-2
LOGIC INPUTS
DE
RE
LOGIC INPUTS
MODE
A, B
RO
DE
RE
MODE
A, B
Y, Z
RO
0
0
Receive
RIN
Driven
0
0
Receive
RIN
High-Z
Driven
0
1
Shutdown
RIN
High-Z
0
1
Shutdown
RIN
High-Z
High-Z
1
0
Transceive
Driven
Driven
1
0
Transceive
RIN
Driven
Driven
1
1
Transmit
Driven
High-Z
1
1
Transmit
RIN
Driven
High-Z
285678fe
8
LTC2856-1/LTC2856-2
LTC2857-1/LTC2857-2
LTC2858-1/LTC2858-2
TYPICAL PERFORMANCE CHARACTERISTICS
Receiver Skew vs Temperature
Driver Propagation Delay
vs Temperature
Driver Skew vs Temperature
2
2
18
RDIFF = 54Ω
CL = 100pF
1
0
RDIFF = 54Ω
CL = 100pF
16
DRIVER PROP DELAY (ns)
DRIVER SKEW (ns)
VAB = 1.5V
CL = 15pF
RECEIVER SKEW (ns)
TA = 25°C, VCC = 5V unless otherwise noted.
1
0
14
12
10
8
6
–1
–40 –20
0
20 40 60 80
TEMPERATURE (°C)
–1
–40 –20
100 120
0
20 40 60 80
TEMPERATURE (°C)
385678 G01
20
40
60
80
100 120
TEMPERATURE (°C)
285678 G03
Driver Output Low/High Voltage
vs Output Current
Driver Differential Output Voltage
vs Temperature
5
160
5
RDIFF = ∞
VOH
OUTPUT VOLTAGE (V)
120
SINK
(VOUT = 5V)
100
4
OUTPUT VOLTAGE (V)
4
SOURCE
(VOUT = 0V)
140
3
2
VOL
1
80
–40 –20
0
20 40 60 80
TEMPERATURE (°C)
0
100 120
0
10
40
30
20
50
OUTPUT CURRENT (mA)
60
0
–40 –20
70
5
70
SOURCE
65
VAB = 1.5V
CL = 15pF
0
SUPPLY CURRENT (mA)
PROP DELAY (ns)
55
50
45
40
0
1
3
4
2
OUTPUT CURRENT (mA)
285678 G07
30
–40 –20
RDIFF = 54Ω
40
RDIFF = 100Ω
30
20
10
35
5
100 120
CL = 100pF
50
60
SINK
20 40
60 80
TEMPERATURE (°C)
Supply Current vs Data Rate
60
4
1
0
285678 G06
Receiver Propagation Delay
vs Temperature
2
RDIFF = 54Ω
2
285678 G05
Receiver Output Voltage vs
Output Current (Source and Sink)
3
RDIFF = 100Ω
3
1
285678 G04
OUTPUT VOLTAGE (V)
0
385678 G02
Driver Output Short-Circuit
Current vs Temperature
OUTPUT SHORT-CIRCUIT CURRENT (mA)
4
–40 –20
100 120
RDIFF = ∞
0
0
20 40 60 80
TEMPERATURE (°C)
100 120
285678 G08
0.1
1
10
DATA RATE (Mbps)
100
285678 G09
285678fe
9
LTC2856-1/LTC2856-2
LTC2857-1/LTC2857-2
LTC2858-1/LTC2858-2
PIN FUNCTIONS
PIN NUMBER
PIN NAME
LTC2856-1
LTC2856-2
LTC2857-1
LTC2857-2
LTC2858-1
LTC2858-2
RO
1
2
1
Receiver Output. If the receiver output is enabled (RE low) and A > B by 200mV,
then RO will be high. If A < B by 200mV, then RO will be low. If the receiver
inputs are open, shorted or terminated without a valid signal, RO will be high.
RE
2
2
Receiver Enable. A low enables the receiver. A high input forces the receiver
output into a high impedance state.
DE
3
3
Driver Enable. A high on DE enables the driver. A low input will force the driver
outputs into a high impedance. If RE is high with DE low, the part will enter a
low power shutdown state.
DI
4
3
4
Driver Input. If the driver outputs are enabled (DE high), then a low on DI forces
the driver positive output low and negative output high. A high on DI, with
the driver outputs enabled, forces the driver positive output high and negative
output low.
GND
5/9*
4/9*
5/11*
Ground. *The Exposed Pad on the DFN packages should be connected to
ground.
Y
5
6
Noninverting Driver Output for the LTC2857-1, LTC2857-2, LTC2858-1 and
LTC2858-2. High impedance when the driver is disabled (LTC2858-1) or
unpowered.
Z
6
7
Inverting Driver Output for the LTC2857-1, LTC2857-2, LTC2858-1 and
LTC2858-2. High impedance when the driver is disabled (LTC2858-1) or
unpowered.
DESCRIPTION
B
7
7
8
Inverting Receiver Input (and Inverting Driver Output for the LTC2856-1 and
LTC2856-2). Impedance is > 96kΩ in receive mode or unpowered.
A
6
8
9
Noninverting Receiver Input (and Noninverting Driver Output for the LTC2856-1
and LTC2856-2). Impedance is > 96kΩ in receive mode or unpowered.
VCC
8
1
10
Positive Supply. 4.5V < VCC < 5.5V. Bypass with a 0.1μF ceramic capacitor.
285678fe
10
LTC2856-1/LTC2856-2
LTC2857-1/LTC2857-2
LTC2858-1/LTC2858-2
BLOCK DIAGRAMS
LTC2856-1, LTC2856-2
LTC2857-1, LTC2857-2
A
(15kV)
RO
RECEIVER
RECEIVER
RO
B
(15kV)
RE
DE
A
(15kV)
SLEEP/SHUTDOWN
LOGIC AND DELAY
B
(15kV)
Z
(15kV)
DI
DRIVER
DRIVER
DI
Y
(15kV)
2856 BD
2857 BD
LTC2858-1, LTC2858-2
A
(15kV)
RO
RECEIVER
B
(15kV)
RE
DE
SLEEP/SHUTDOWN
LOGIC AND DELAY
Z
(15kV)
DI
DRIVER
Y
(15kV)
2858 BD
285678fe
11
LTC2856-1/LTC2856-2
LTC2857-1/LTC2857-2
LTC2858-1/LTC2858-2
APPLICATIONS INFORMATION
Driver
The driver provides full RS485 and RS422 compatibility.
When enabled, if DI is high, Y-Z is positive for the full-duplex
devices and A-B is positive for the half-duplex device.
When the driver is disabled, both outputs are high impedance. For the full-duplex devices, the leakage on the driver
output pins is guaranteed to be less than 10μA over the
entire common mode range of –7V to 12V. On the halfduplex device, the impedance is dominated by the receiver
input resistance, RIN.
Driver Overvoltage and Overcurrent Protection
The driver outputs are protected from short circuits
to any voltage within the Absolute Maximum range of
(VCC – 15V) to 15V. The maximum current in this condition
is 250mA. If the pin voltage exceeds about ±10V, current
limit folds back to about half of the peak value to reduce
overall power dissipation and avoid damaging the part.
All devices also feature thermal shutdown protection that
disables the driver and receiver output in case of excessive
power dissipation (see Note 4).
Slew Limiting for EMI Emissions Control
The LTC2856-2, LTC2857-2 and the LTC2858-2 feature
reduced slew rate driver outputs to control the high frequency EMI emissions from equipment and data cables.
These devices are limited to data rates of 250kbaud or
less. Slew limiting also mitigates the adverse affects of
imperfect transmission line termination caused by stubs
or mismatched cable.
Figures 10 and 11 show the output waveforms from
the LTC2858-1 and its slew rate limited counterpart, the
LTC2858-2, operating at 250kbps. The corresponding
frequency spectrums show significant reduction in the high
frequency harmonics for the slew rate limited device.
Receiver and Failsafe
With the receiver enabled, when the absolute value of the
differential voltage between the A and B pins is greater than
200mV, the state of RO will reflect the polarity of (A-B).
These parts have a failsafe feature that guarantees the
receiver output to be in a logic-high state when the inputs
are either shorted, left open or terminated, but not driven
for more than about 3μs. The delay prevents signal zero
crossings from being interpreted as shorted inputs and
causing RO to go high inadvertently. This failsafe feature
is guaranteed to work for inputs spanning the entire common mode range of –7V to 12V.
The receiver output is internally driven high (to VCC) or
low (to ground) with no external pull-up needed. When
the receiver is disabled the RO pin becomes high-Z with
leakage of less than ±1μA for voltages within the supply
range.
Receiver Input Resistance
The receiver input resistance from A or B to ground is
guaranteed to be greater than 96k (C, I-Grade). This is 8×
higher than the requirements for the RS485 standard and
thus this receiver represents a one-eighth unit load. This,
in turn, means that 8× the standard number of receivers,
or 256 total, can be connected to a line without loading
it beyond what is called out in the RS485 standard. The
receiver input resistance from A or B to ground on high
temperature H-Grade parts is greater than 48k providing
a one-quarter unit load. The input resistance of the receivers is unaffected by enabling/disabling the receiver and
by powering/unpowering the part.
Supply Current
The unloaded static supply currents in these devices are
very low—typically under 700μA for all modes of operation. In applications with resistively terminated cables,
the supply current is dominated by the driver load. For
example, when using two 120Ω terminators with a differential driver output voltage of 2V, the DC load current
is 33mA, which is sourced by the positive voltage supply.
Power supply current increases with toggling data due to
capacitive loading and this term can increase significantly
at high data rates. Figure 8 shows supply current vs data
rate for two different capacitive loads for the circuit configuration of Figure 4.
285678fe
12
LTC2856-1/LTC2856-2
LTC2857-1/LTC2857-2
LTC2858-1/LTC2858-2
APPLICATIONS INFORMATION
Cable Length vs Data Rate
RDIFF = 54Ω
CURRENT (mA)
70
65
CL = 1000pF
60
55
CL = 100pF
50
45
102
104
103
DATA RATE (kbps)
105
285678 F08
Figure 8. Supply Current vs Data Rate
High Speed Considerations
A ground plane layout is recommended. A 0.1μF bypass
capacitor less than one-quarter inch away from the VCC pin
is also recommended. The PC board traces connected to
signals A/B and Z/Y should be symmetrical and as short
as possible to maintain good differential signal integrity.
To minimize capacitive effects, the differential signals
should be separated by more than the width of a trace
and should not be routed on top of each other if they are
on different signal planes.
Care should be taken to route outputs away from any
sensitive inputs to reduce feedback effects that might
cause noise, jitter or even oscillations. For example, in the
full-duplex LTC2857-1, DI and A/B should not be routed
near the driver or receiver outputs.
The logic inputs have 100mV of hysteresis to provide noise
immunity. Fast edges on the outputs can cause glitches in
the ground and power supplies which are exacerbated by
capacitive loading. If a logic input is held near its threshold
(typically 1.5V), a noise glitch from a driver transition may
exceed the hysteresis levels on the logic and data input
pins causing an unintended state change. This can be
avoided by maintaining normal logic levels on the pins
and by slewing inputs through their thresholds by faster
than 1V/μs when transitioning. Good supply decoupling
and proper line termination also reduce glitches caused
by driver transitions.
For a given data rate, the maximum transmission distance
is bounded by the cable properties. A typical curve of cable
length vs data rate compliant with the RS485 standard is
shown in Figure 9. Three regions of this curve reflect different performance limiting factors in data transmission. In the
flat region of the curve, maximum distance is determined
by resistive losses in the cable. The downward sloping
region represents limits in distance and data rate due to
AC losses in the cable. The solid vertical line represents the
specified maximum data rate in the RS485 standard. The
dashed line at 250kbps shows the maximum data rate of
the low-EMI LTC2856-2, LTC2857-2, and LTC2858-2. The
dashed line at 20Mbps shows the maximum data rates of
the LTC2856-1, LTC2857-1 and LTC2858-1.
10k
CABLE LENGTH (FT)
75
LOW-EMI MODE
MAX DATA RATE
1k
NORMAL
MODE MAX
DATA RATE
100
RS485 MAX
DATA RATE
10
10k
100k
1M
10M
DATA RATE (bps)
100M
285678 F09
Figure 9. Cable Length vs Data Rate
(RS485 Standard Shown in Solid Vertical Lines)
Cable Termination
Proper cable termination is very important for good
signal fidelity. If the cable is not terminated with its characteristic impedance, reflections will result in distorted
waveforms.
RS485 transceivers typically communicate over twistedpair cables with characteristic impedance ranging from
100Ω to 120Ω. Each end of the network should be terminated with a discrete resistor matching the characteristic
impedance or with an LTC2859/LTC2861 transceiver with
integrated termination capability.
285678fe
13
LTC2856-1/LTC2856-2
LTC2857-1/LTC2857-2
LTC2858-1/LTC2858-2
APPLICATIONS INFORMATION
Time-Based Traces
Frequency Spectrum
Y, Z
1V/DIV
Y-Z
10dB/DIV
Y-Z
2V/DIV
2μs/DIV
285678 F10a
1.25MHz/DIV
285678 F10b
Figure 10. LTC2858-1 Driver Output at 100kHz Into 100Ω Resistor
285678fe
14
LTC2856-1/LTC2856-2
LTC2857-1/LTC2857-2
LTC2858-1/LTC2858-2
APPLICATIONS INFORMATION
Time-Based Traces
Frequency Spectrum
Y, Z
1V/DIV
Y-Z
10dB/DIV
Y-Z
2V/DIV
285678 F11a
2μs/DIV
1.2MHz/DIV
285678 F11b
Figure 11. LTC2858-2 Driver Output at 100kHz Into 100Ω Resistor
TYPICAL APPLICATIONS
Failsafe “0” Application (Idle State = Logic “0”)
VCC
100k
I1
RO
R
B
A
DI
I2
“A”
“B”
D
LTC2856-1
285678 TA02
285678fe
15
LTC2856-1/LTC2856-2
LTC2857-1/LTC2857-2
LTC2858-1/LTC2858-2
PACKAGE DESCRIPTION
DD Package
8-Lead Plastic DFN (3mm × 3mm)
(Reference LTC DWG # 05-08-1698)
0.675 p 0.05
3.5 p 0.05
1.65 p 0.05
2.15 p 0.05 (2 SIDES)
PACKAGE
OUTLINE
0.25 p 0.05
0.50
BSC
2.38 p 0.05
(2 SIDES)
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
3.00 p 0.10
(4 SIDES)
R = 0.115
TYP
5
0.38 p 0.10
8
1.65 p 0.10
(2 SIDES)
PIN 1
TOP MARK
(NOTE 6)
(DD) DFN 1203
0.200 REF
0.75 p 0.05
4
0.25 p 0.05
1
0.50 BSC
0.00 – 0.05
2.38 p 0.10
(2 SIDES)
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WEED-1)
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
ON TOP AND BOTTOM OF PACKAGE
285678fe
16
LTC2856-1/LTC2856-2
LTC2857-1/LTC2857-2
LTC2858-1/LTC2858-2
PACKAGE DESCRIPTION
DD Package
10-Lead Plastic DFN (3mm × 3mm)
(Reference LTC DWG # 05-08-1699)
R = 0.115
TYP
0.38 p 0.10
6
10
5
1
0.675 p 0.05
3.50 p 0.05
1.65 p 0.05
2.15 p 0.05 (2 SIDES)
3.00 p 0.10
(4 SIDES)
PACKAGE
OUTLINE
PIN 1
TOP MARK
(SEE NOTE 6)
0.200 REF
0.25 p 0.05
1.65 p 0.10
(2 SIDES)
0.50
BSC
2.38 p 0.05
(2 SIDES)
(DD) DFN 1103
0.25 p 0.05
0.50 BSC
0.75 p 0.05
0.00 – 0.05
2.38 p 0.10
(2 SIDES)
BOTTOM VIEW—EXPOSED PAD
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
NOTE:
1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WEED-2).
CHECK THE LTC WEBSITE DATA SHEET FOR CURRENT STATUS OF VARIATION ASSIGNMENT
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE
TOP AND BOTTOM OF PACKAGE
285678fe
17
LTC2856-1/LTC2856-2
LTC2857-1/LTC2857-2
LTC2858-1/LTC2858-2
PACKAGE DESCRIPTION
MS8 Package
8-Lead Plastic MSOP
(Reference LTC DWG # 05-08-1660)
0.889 p 0.127
(.035 p .005)
5.23
(.206)
MIN
3.20 – 3.45
(.126 – .136)
0.42 p 0.038
(.0165 p .0015)
TYP
3.00 p 0.102
(.118 p .004)
(NOTE 3)
0.65
(.0256)
BSC
8
7 6 5
0.52
(.0205)
REF
RECOMMENDED SOLDER PAD LAYOUT
0.254
(.010)
3.00 p 0.102
(.118 p .004)
(NOTE 4)
4.90 p 0.152
(.193 p .006)
DETAIL “A”
0° – 6° TYP
GAUGE PLANE
1
0.53 p 0.152
(.021 p .006)
DETAIL “A”
2 3
4
1.10
(.043)
MAX
0.86
(.034)
REF
0.18
(.007)
SEATING
PLANE
0.22 – 0.38
(.009 – .015)
TYP
0.65
(.0256)
BSC
0.1016 p 0.0508
(.004 p .002)
MSOP (MS8) 0307 REV F
NOTE:
1. DIMENSIONS IN MILLIMETER/(INCH)
2. DRAWING NOT TO SCALE
3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS.
INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX
285678fe
18
LTC2856-1/LTC2856-2
LTC2857-1/LTC2857-2
LTC2858-1/LTC2858-2
PACKAGE DESCRIPTION
MS Package
10-Lead Plastic MSOP
(Reference LTC DWG # 05-08-1661)
0.889 p 0.127
(.035 p .005)
5.23
(.206)
MIN
3.20 – 3.45
(.126 – .136)
3.00 p 0.102
(.118 p .004)
(NOTE 3)
0.50
0.305 p 0.038
(.0197)
(.0120 p .0015)
BSC
TYP
RECOMMENDED SOLDER PAD LAYOUT
0.254
(.010)
3.00 p 0.102
(.118 p .004)
(NOTE 4)
4.90 p 0.152
(.193 p .006)
DETAIL “A”
0.497 p 0.076
(.0196 p .003)
REF
10 9 8 7 6
0° – 6° TYP
GAUGE PLANE
1 2 3 4 5
0.53 p 0.152
(.021 p .006)
DETAIL “A”
0.86
(.034)
REF
1.10
(.043)
MAX
0.18
(.007)
SEATING
PLANE
0.17 – 0.27
(.007 – .011)
TYP
0.50
(.0197)
BSC
0.1016 p 0.0508
(.004 p .002)
MSOP (MS) 0307 REV E
NOTE:
1. DIMENSIONS IN MILLIMETER/(INCH)
2. DRAWING NOT TO SCALE
3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS.
INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX
285678fe
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
19
LTC2856-1/LTC2856-2
LTC2857-1/LTC2857-2
LTC2858-1/LTC2858-2
TYPICAL APPLICATION
Multi-Node Network and End Termination Using the LTC2856-1
R
D
R
LTC2856-1
D
LTC2856-1
R
R
TE = 5V
TE = 5V
D
D
LTC2859
LTC2859
285678 TA03
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LTC485
Low Power RS485 Interface Transceiver
ICC = 300μA (Typ)
LTC491
Differential RS485 Driver and Receiver Pair
ICC = 300μA
LTC1480
3.3V Ultralow Power RS485 Transceiver
3.3V Operation
LTC1483
Ultralow Power RS485 Low EMI Transceiver
Controlled Driver Slew Rate
LTC1485
Differential Bus Transceiver
10Mbaud Operation
LTC1487
Ultralow Power RS485 with Low EMI, Shutdown and High Input
Impedance
Up to 256 Transceiver on the Bus
LTC1520
50Mbps Precision Quad Line Receiver
Channel-to-Channel Skew 400ps (Typ)
LTC1535
Isolated RS485 Full-Duplex Transceiver
2500VRMS Isolation in Surface Mount Package
LTC1685
52Mbps RS485 Transceiver with Precision Delay
Propagation Delay Skew 500ps (Typ)
LT1785
60V Fault Protected RS485 Transceiver
60V Tolerant, ±15kV ESD
LTC2859/
LTC2861
20Mbps RS485 Transceivers with Integrated Switchable Termination
Integrated, Switchable, 120Ω Termination Resistor,
±15kV ESD
285678fe
20 Linear Technology Corporation
LT 0308 REV E • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2006
Similar pages