EMB1M THRU EMB6M SINGLE PHASE 0.8AMP SUPER FAST GLASS PASSIVATED BRIDGE RECTIFIER Features · Glass Passivated Die Construction · Low leakage · Ideal for printed circuit board · Surge overload rating-30A peak · Designed for Surface Mount Application · Plastic Material-UL Flammability 94V-0 MBM 0.157（4.0） 0.134（3.4） - + ~ ~ 0.012（0.30） 0.028（ 0.7） 0.016（ 0.4） 0.051（1.3） 0.035（0.9） Mechanical Data · 0.236（ 6.0） 0.213（5.4 ） 0.106（2.7） 0.091（2.3） Case:Reliable low cost construction 0.203（5.15 ） 0.179（4.55） utilizing molded plastic technique · 0.004（0.10） Terminals:Plated Leads Solderable per MIL- 0.106（2.7） STD-202,Method208 0.091（2.3） · Polarity:As Marked on Case · Mounting Position:Any · Marking:Type Number 0.193（4.90） 0.177（4.50） dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ ambient temperature unless otherwise specified. Single Phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. TYPE NUMBER SYMBOL EMB1M EMB2M EMB4M 100 200 400 70 140 280 EMB6M UNITS VRRM Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage VRWM RMS Reverse Voltage VRMS 600 V VDC Average Rectified Output Current (Note 1)@TC=100℃ (Note 2)@TC=100℃ IF(AV) 420 V 0.5 0.8 A Non-Repetitive Peak Forward Surge Current 8.3ms Single half sine-wave superimposed on rated load (JEDEC Method) IFSM 30 A I2t Rating for Fusing (t < 8.3ms) I 2t 3.735 A2s Forward Voltage per element @IF=0.8A Peak Reverse Current At Rated DC Blocking Voltage @TA=25℃ @TA=125℃ Maximum reverse recovery time (Note 3) Typical Junction Capacitance per leg (Note 4) Typical Thermal Resistance per leg Operating and Storage Temperature Range VFM 0.95 1.25 1.75 V IR 5.0 200 uA TRR 35 ns CJ 13 pF RθJA 60 RθJL 16 TJ,TSTG -55to+150 ℃/W ℃ 2 Note:1. Mounted on glass epoxy PC board with 1.3mm solder pad. 2 2. Mounted on aluminum substrate PC board with 1.3mm solder pad. 3. Reverse Recovery Test Conditions: IF=0.5A, IR=1A, Irr=0.25A. 4. Measured at 1.0 MHz and applied reverse voltage of 4.0V D.C. version:02 1 of 3 www.dyelec.com IF, INSTANTANEOUS FORWARD CURRENT (A) Fig. 1 Output Current Derating Curve 1.0 Al. Substrate PC Board 0.6 0.4 Glass Epoxy PC Board 0.2 0 Resistive or Inductive Load 40 80 120 TC , CASE TEMPERATURE (°C) 0 Fig. 2 Typical Forward Characteristics (per leg) 10 EMB1M-EMB2M EMB4M 1.0 EMB6M 0.1 TA= 25°C Pulse Width = 300µs 0.01 0.3 160 0.69 0.9 1.2 1.5 1.8 Fig. 3 Maximum Peak Forward Surge Current (per leg) 35 Fig. 4 Typical Junction Capacitance 100 TJ = 25°C f = 1.0MHz 30 20 10 TA = 25°C Single Half Sine-Wave Pulse Width = 8.3ms (JEDEC Method) 0 2.1 VF, INSTANTANEOUS FORWARD VOLTAGE (V) Cj, JUNCTION CAPACITANCE (pF) IFSM, PEAK FORWARD SURGE CURRENT (A) I(AV), AVERAGE FORWARD RECTIFIED CURRENT (A) EMB1M THRU EMB6M 10 1 1.0 10 1 NUMBER OF CYCLES AT 60 Hz 10 100 VR, REVERSE VOLTAGE (V) INVSTANTANEOUS REVERSE CURRENT (µA) FIG.5 TYPICAL REVERSE CHRACTERISTICS 1000 O TJ= 125 C 100 10 1.0 O TJ= 25 C 0.1 20 40 60 80 100 120 PERCENT OF RATED PEAK INVERSE VOLTGE (V) version:02 2 of 3 www.dyelec.com EMB1M THRU EMB6M Important Notice and Disclaimer •Reproducing and modifying information of the document is prohibited without permission from DIYI. • DIYI reserves the right to make changes to this document and its products and specifications at any time without notice. Customers should obtain and confirm the latest product information and specifications before final design, purchase or use. •DIYI disclaims any and all liability arising out of the application or use of any product including damages incidentally and consequentially occurred. •DIYI does not assume any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Applications shown on the here in document are examples of standard use and • operation. Customers are responsible in comprehending the suitable use in particular applications. DIYI makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. •The products shown here in are not designed and authorized for equipments requiring high level of reliability or relating to human life and for any applications concerning life-saving or life-sustaining, such as medical instruments, transportation equipment, aerospace machinery et cetera. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify DIYI for any damages resulting from such improper use or sale. •Since DIYI uses lot number as the tracking base, please provide the lot number for tracking when complaining. version:02 3 of 3 www.dyelec.com