AVX LCCM0805M100GTAR Lccm series â chip common mode filter Datasheet

Chip Inductors
LCCM Series – Chip Common Mode Filter
FEATURES
CONSTRUCTION
• Small wire wound chip inductor with ferrite core and 2 common
mode lines.
• Highly effective in noise suppression
• High common-mode impedance at noise band an low
differential mode impedance at signal band factor. There is
almost no distortion in high-speed signals.
• Operating temperature -40°C ~ 85°C.
APPLICATIONS
Ferrite
• EMI suppression for electronic devices.
• USB line in personal computers and peripherals.
• IEEE 1394 line for personal computers, DVC, and STB
• LCD Panels.
• Low-Voltage Differential Signal (LVDS)
Terminal
Enamel-insulated
Wire
DIMENSIONS
B
A
K
C
H K
E
I
F
J
E
I
G
mm (inches)
Type
Size
(inch)
LCCM0805
0805
LCCM1206
1206
A
2.00
(0.079
3.20
(0.126
B
C
± 0.20
1.20 ± 0.20
1.20 ± 0.20
± 0.008) (0.047 ± 0.008) (0.047 ± 0.008)
± 0.20
1.60 ± 0.20
1.80 ± 0.20
± 0.008) (0.063 ± 0.008) (0.071 ± 0.008)
E
F
G
H
I
J
K
0.45
(0.018)
1.20
(0.047)
0.40
(0.016)
0.80
(0.031)
0.40
(0.016)
0.40
(0.016)
0.90
(0.035)
0.60
(0.024)
2.00
(0.079)
0.60
(0.024)
1.60
(0.063)
0.60
(0.024)
0.40
(0.016)
1.05
(0.041)
Weight (g)
(1000pcs)
19
53.3
HOW TO ORDER
LC
CM
0805
M
101
G
T
A
R
Family
LC = Chip Inductor
Series
CM = Common Mode
Size
0805
1206
Tolerance
M = 20%
Impedance
100 = 10 Ω
101 = 100 Ω
102 = 1000 Ω
Style
G = Standard
Termination
T = Sn Plating
Special
A = Standard
Packaging
R = 7" Reel
2
Chip Inductors
LCCM Series – Chip Common Mode Filter
ELECTRICAL CHARACTERISTICS
0805
Impedance
(Ω)
Tolerance
67
90
120
180
200
260
360
370
±20%
±20%
±20%
±20%
±20%
±20%
±20%
±20%
Test
Condition
(MHz)
100
100
100
100
100
100
100
100
DCR
(Ω) max.
IDC
(mA) max.
Rated Voltage
Vdc (V)
0.25
0.35
0.30
0.35
0.35
0.40
0.40
0.40
400
330
370
330
330
300
280
280
50
50
50
50
50
50
50
50
Test
Condition
(MHz)
100
100
100
100
100
100
DCR
(Ω) max.
IDC
(mA) max.
Rated Voltage
Vdc (V)
0.30
0.40
0.50
0.80
1.00
1.20
370
340
310
260
230
200
50
50
50
50
50
50
Withstanding
Voltage Vdc
(V)
125
125
125
125
125
125
125
125
Insulation
Resistance
(MΩ) min.
10
10
10
10
10
10
10
10
Withstanding
Voltage Vdc
(V)
125
125
125
125
125
125
Insulation
Resistance
(MΩ) min.
10
10
10
10
10
10
1206
Impedance
(Ω)
Tolerance
90
160
260
600
1000
2200
±20%
±20%
±20%
±20%
±20%
±20%
3
Chip Inductors
LCCM Series – Chip Common Mode Filter
LCCM0805 CHARACTERISTICS – IMPEDANCE vs. FREQUENCY
LCCM0805M670
LCCM0805M900
10000
1000
1
Impedance (Ohm)
10
100
10
10
100
1000
1
Frequency (MHz)
1
1000
1
100
10
1000
10
100
1
1000
10
LCCM0805M201
LCCM0805M361
10000
1000
100
10
1
100
10
1
0.1
0.1
1
10
100
1000
Frequency (MHz)
Common Mode
1
100
Frequency (MHz)
Frequency (MHz)
Impedance (Ohm)
Impedance (Ohm)
10
0.1
1
Frequency (MHz)
1000
100
1
0.1
100
1000
1000
1
10
100
LCCM0805M371
10000
Impedance (Ohm)
10
1
10
Frequency (MHz)
1000
100
0.1
4
100
LCCM0805M181
10000
Impedance (Ohm)
Impedance (Ohm)
10
Frequency (MHz)
LCCM0805M121
1000
10
0.1
0.1
1
100
1
1
0.1
LCCM0805M261
10000
1000
100
Impedance (Ohm)
Impedance (Ohm)
1000
10
100
Frequency (MHz)
Differential Mode
1000
1000
Chip Inductors
LCCM Series – Chip Common Mode Filter
LCCM1206 CHARACTERISTICS – IMPEDANCE vs. FREQUENCY
LCCM1206M900
LCCM1206M261
10000
100
10
1
1000
100
10
10
100
1000
1
Frequency (MHz)
100
10
1
100
Frequency (MHz)
1
1000
10
100
1000
Frequency (MHz)
LCCM1206M222
10000
1000
100
10
1000
100
10
1
1
10
10
1000
Impedance (Ohm)
Impedance (Ohm)
Impedance (Ohm)
10
LCCM1206M601
10000
100
1
100
Frequency (MHz)
LCCM1206M161
1000
1000
1
1
1
LCCM1206M102
10000
Impedance (Ohm)
Impedance (Ohm)
Impedance (Ohm)
1000
1
10
100
1000
Frequency (MHz)
Common Mode
1
10
100
1000
Frequency (MHz)
Differential Mode
5
Chip Inductors
LCCM Series – Chip Common Mode Filter
ENVIRONMENTAL CHARACTERISTICS
ELECTRICAL PERFORMANCE TEST
Items
Impedance
DC Resistance DCR
Requirement
Withstand Voltage (VDC)
Refer to standard electrical
characteristic spec.
Component should not
be damaged
Rated Voltage (VDC)
Insulation Resistance (I.R)
Test Conditions I Test Methods
LCR Meter HP 4291B
Micro-Ohm meter (GOM-801G)
Test Voltage: 2.5 Times Rated Voltage
Testing Time: 60 seconds
Charge Current: 0.5mA
Test Voltage: Rated Voltage
Testing Time: 1 to 5 seconds
Charge Current: 1mA
Charge Current: 1minute
10M ohm min.
MECHANICAL PERFORMANCE TEST
Items
Component Adhesion
(Push Test)
Requirement
Base: 0805 2 Lbs
Cover: 0805 1 Lbs
Base: 1206 4 Lbs
Cover: 1206 2 Lbs
Drop
Component should not
be damaged
Solderability
The terminal should at least
be 90% covered with solder
Vibration Test
(Low Frequency)
Component should not
be damaged
Test Conditions I Test Methods
The component should be soldered (232°C ± 5°C
for 10 sec.) to tinned copper substrate
Applied force gauge to the side of component
It must withstand force of 2 or 4 pounds without
failure of the component.
Dropping chip by each side and corner.
Drop 10 times in total
Drop height: 100 cm
Drop weight: 125 g
The component shall be dipped in a
melted solder bath at 245 ±5°C for 3 seconds
1.
2.
3.
4.
Amplitude: 1.5 m/m
Frequency: 10-55-10Hz (1min.)
Direction: X, Y, Z
Duration: 2 Hrs/X, Y, Z
MECHANICAL PERFORMANCE TEST
Items
Requirement
Low Temperature Storage
Test Conditions I Test Methods
1. Temp: -40 ±2°C
2. Time: 1000±48 Hours
3. Component should be tested after 1 hour
at room temperature
ROOM TEMP
Thermal Shock
Impedance change: Within± 20%
Without distinct damage
in appearance
High Temperature Storage
Humidity
High Temperature Load Life
There should be no evidence of
short or open circuit
Low Temperature Load Life
6
-25 ± 2ºC
15 MINS
30 MINS
ROOM TEMP
85 ± 2ºC
Total: 5 Cycles
15 MINS
30 MINS
1. Temp: 85 ± 2°C
2. Time: 1000 ± 48 Hours
3. Component should be tested after 1 hour
at room temperature
1. Temp: 40 ± 2°C
2. R.H. : 90 — 95%
3. Time: 48 ±2 Hours
1. Temp: 85 ± 2°C
2. Time: 96 ± 12 Hours
3. Load: Allowed DC Current
1. Temp: -40 ± 2°C
2. Time: 96 ± 12 Hours
3. Load: Allowed DC Current
Chip Inductors
LCCM Series – Chip Common Mode Filter
PACKAGING QUANTITY REAL SPECIFICATIONS
1.20 ± 0.20
(0.047 ± 0.008)
D: 21.8 ± 0.80
(0.858 ± 0.031)
Type
LCCM0805
LCCM1206
Label
178 ± 2.00
(7.008 ± 0.079)
Embossed
Plastic Tape
(EA)
2,000
2,000
60.0 ± 0.50
(2.362 ± 0.020)
D: 13.0 ± 0.30
(0.512 ± 0.012)
9.00 ± 0.30
(0.354 ±0.0112)
2.00 ± 0.50
(0.079 ±0.020)
11.4 ± 1.00
(0.449 ± 0.039)
EMBOSSED PLASTIC TAPE SPECIFICATIONS
Top Tape
ψ D0
E
A
F
B
W
ψ D11.5 Min.
T
P1
P2
P0
Direction of unreeling
Embossed Tape
mm (inches)
A
B
W
E
F
P0
P1
P2
ΦD0
T
1.40 ± 0.10
2.55 ± 0.05
8.0 ± 0.20
1.75 ± 0.10
3.50 ± 0.10
4.00 ± 0.10
4.00 ± 0.10
2.00 ± 0.10
1.50 ± 0.10
1.35 ± 0.10
LCCM0805
(0.055 ± 0.004) (0.100 ± 0.002) (0.315 ± 0.008) (0.069 ± 0.004) (0.138 ± 0.004) (0.157 ± 0.004) (0.157 ± 0.004) (0.079 ± 0.004) (0.059 ± 0.004) (0.053 ± 0.004)
1.90 ± 0.10
3.50 ± 0.05
8.0 ± 0.20
1.75 ± 0.10
3.5 ± 0.10
4.00 ± 0.10
4.00 ± 0.10
2.00 ± 0.10
1.50 ± 0.10
2.10 ± 0.10
LCCM1206
(0.075 ± 0.004) (0.138 ± 0.004) (0.315 ± 0.008) (0.069 ± 0.004) (0.138 ± 0.004) (0.157 ± 0.004) (0.157 ± 0.004) (0.079 ± 0.004) (0.059 ± 0.004) (0.083 ± 0.004)
Type
LEADER/TAPE
Trailer End
Leader
Trailer
80.0 (3.150) min.
Empty Compartments
with Cover Tape
80.0 (3.150) min.
Cover
Tape Only
450 (17.72) min.
PEEL-OFF FORCE
The force for tearing off cover tape is 0.05 - 0.69 (N)
in the arrow direction at the following conditions:
Temperature: 5 - 35°C
Humidity: 45 - 85%
Atmospheric pressure: 860 - 1060hpa
160 - 180º
Top cover tape
Base tape
7
Similar pages