ON NCP1596 1.5 mhz current mode pwm buck down converter Datasheet

NCP1596, NCP1596A
Product Preview
1.5 A, 1.5 MHz Current
Mode PWM Buck Down
Converter
http://onsemi.com
The NCP1596/NCP1596A is a current mode PWM buck converter
with integrated power switch. It can provide up to 1.5 A output current
with high conversion efficiency. High frequency PWM control
scheme can provide a low output ripple noise. Thus, it allows the
usage of small size passive components to reduce the board space. In a
low load condition, the controller will automatically change to PFM
mode which provides a higher efficiency at low load. Additionally, the
device includes soft−start, thermal shutdown with hysteresis,
cycle−by−cycle current limit, and short circuit protection. This device
is available in a compact 3x3 DFN package.
1
6 PIN DFN 3x3
MN SUFFIX
CASE 506AH
MARKING DIAGRAMS
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
High Efficiency up to 90%, 1 A @ 3.3 V, 75% @ 1.2 V
Fully Internal Compensation
Low Output Voltage Ripple, 20 mV Typical
±1.5% Reference Voltage
High PWM Switching Frequency, 1.5 MHz
Automatic PWM / PFM Switchover at Light Load
Built−in 1 ms Digital Soft Start
Cycle−by−cycle Current Limit
Thermal Shutdown with Hysteresis
Internal UVLO Protection
Ext. Adjustable Output Voltage
Low Profile and Minimum External Components
Designed for use with Ceramic Capacitor
Compact 3x3 DFN Package
These are Pb−Free Devices
1 N1596
ALYW
G
1 1596A
ALYW
G
N1596/1596A = Specific Device Code
A
= Assembly Location
L
= Wafer Lot
Y
= Year
W = Work Week
G
= Pb−Free Package
PIN CONNECTIONS
FB
GND
LX
NC
VCC
VCCP
FB
GND
LX
1596
EN
VCC
VCCP
1596A
(Top View)
Typical Applications
• Hard Disk Drives
• USB Power Device
• Wireless and DSL Modems
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 11 of this data sheet.
This document contains information on a product under development. ON Semiconductor
reserves the right to change or discontinue this product without notice.
© Semiconductor Components Industries, LLC, 2009
March, 2009 − Rev. P3
1
Publication Order Number:
NCP1596/D
NCP1596, NCP1596A
L1
VIN = 4.0 V to 5.5 V
NCP1596
D1
VCC
C1
NC/EN
VOUT = 0.8 V to 0.9 x VIN
LX
VCCP
GND
R1
C2
FB
R2
Figure 1. Typical Operating Circuit
ABSOLUTE MAXIMUM RATINGS
Rating
Symbol
Value
Unit
Power Supply (Pins 4, 5)
VIN
6.0
−0.3 (DC)
−1.0 (100 ns)
V
Input / Output Pins
Pins 1, 3, 6
VIO
6.0
−0.3 (DC)
−1.0 (100 ns)
V
PD
RqJA
1450
68.5
mW
°C/W
Operating Junction Temperature Range (Note 4)
TJ
−40 to +150
°C
Operating Ambient Temperature Range
TA
−40 to +85
°C
Storage Temperature Range
Tstg
Thermal Characteristics
3x3 DFN Plastic Package
Maximum Power Dissipation @ TA = 25°C
Thermal Resistance Junction−to−Air
−55 to +150
°C
Lead Temperature Soldering (10 sec)
230
°C
Moisture Sensitivity Level (Note 3)
1.0
−
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
NOTE: ESD data available upon request.
1. This device series contains ESD protection and exceeds the following tests:
Human Body Model (HBM) 2.0 kV per JEDEC standard: JESD22−A114.
Machine Model (MM) 200 V per JEDEC standard: JESD22−A115.
2. Latch−up Current Maximum Rating: 150 mA per JEDEC standard: JESD78.
3. Moisture Sensitivity Level (MSL): 1 per IPC/JEDEC standard: J−STD−020A.
4. The maximum package power dissipation limit must not be exceeded.
PD +
T J(max) * T A
R qJA
http://onsemi.com
2
NCP1596, NCP1596A
ELECTRICAL CHARACTERISTICS
(VIN = 5.0 V, VOUT = 1.2 V, TA = 25°C for typical value, −40°C ≤ TA ≤ 85°C for min/max values unless otherwise noted)
Symbol
Min
Typ
Max
Unit
VIN
4.0
−
5.5
V
Under Voltage Lockout Threshold
VUVLO
3.2
3.5
3.8
V
Under Voltage Lockout hysteresis
VUVLO_HYS
−
180
−
mV
PFET Leakage Current (Pins 5, 4)
TA = 25°C
TA = −40°C to 85°C
ILEAK−P
−
−
1.0
−
10
15
Characteristic
Operating Voltage
mA
FEEDBACK VOLTAGE
FB Input Threshold (TA = −40°C to 85°C)
VFB
0.788
0.800
0.812
V
FB Input Current
IFB
−
10
100
nA
Thermal Shutdown Threshold (Note 5)
TSHDN
−
160
−
°C
Hysteresis
TSDHYS
−
30
−
°C
FOSC
1.27
1.5
1.725
MHz
THERMAL SHUTDOWN
PWM SMPS MODE
Switching Frequency (TA = −40°C to 85°C)
Internal PFET ON−Resitance (ILX = 100 mA, VIN = 5.0 V, TA = 25°C) (Note 5)
RDS(on)_P
−
0.2
0.3
Ohm
Minimum Duty Cycle
DMIN
−
0
−
%
Maximum Duty Cycle
DMAX
−
100
−
%
Soft−Start Time (VIN = 5.0 V, Vo = 1.2 V, ILOAD = 0 mA, TA = 25°C)
TSS
0.8
1.0
1.2
ms
Main PFET Switch Current Limit (Note 5)
ILIM
2.0
2.5
−
A
Enable Threshold High (NCP1596A Only)
VEN_H
1.8
−
−
V
Enable Threshold Low
VEN_L
−
−
0.4
V
IEN
−
500
TBD
nA
Output Load Current 10 mA @ 1.2 V (Note 5)
h
−
50
−
%
Output Load Current 100 mA to 1.2 A @ 1.2 V (Note 5)
h
−
70
−
%
Quiescent Current Into VCCP (VIN = 5 V, VFB = 1.0 V, TA = 25°C)
ICCP
−
10
−
mA
Quiescent Current Into VCC (VIN = 5 V, VFB = 1.0 V, TA = 25°C)
ICC
−
500
−
mA
ICC_SD
−
1.0
3.0
mA
ENABLE − NCP1596A
Enable bias current (EN = 0 V)
EFFICIENCY
TOTAL DEVICE
Shutdown Quiescent Current into VCC and VCCP (NCP1596A Only)
(EN = 0, VIN = 5 V, VFB = 1.0 V, TA = 25°C)
5. Values are design guaranteed.
http://onsemi.com
3
NCP1596, NCP1596A
PIN FUNCTION DESCRIPTIONS
Pin #
Symbol
Pin Description
NCP1596
1
FB
Feedback pin. Part is internally compensated. Only necessary to place a voltage divider or connect the output directly to this pin.
2
GND
3
LX
4
VCCP
5
VCC
6
NC
No Connection
1
FB
Feedback pin. Part is internally compensated. Only necessary to place a voltage divider or connect the output directly to this pin.
2
GND
Ground
Pin connected internally to power switch. Connect externally to inductor.
Power connection to the power switch.
IC power connection.
NCP1596A
3
LX
4
VCCP
5
VCC
6
EN
Ground
Pin connected internally to power switch. Connect externally to inductor.
Power connection to the power switch.
IC power connection.
Device Enable pin. This pin has an internal current source pull up. No connect is enable the device. With this
pin pulled down below 0.8 V, the device is disabled and enters the shutdown mode.
NC/EN
Vin
C1
Isense
UVLO
VCC
Thermal
Shutdown
Isense
Short
circuit
protect
VCCP
disable
500 nA
Oscillator
Vout = 0.8 V to 0.9 V * Vin
Soft Start
S
FB
Q
L1
LX
driver
R
0.8 V
Q
R1
Ton(min)
D1
GND
C2
R2
Figure 2. Detail Block Diagram
EXTERNAL COMPONENT REFERENCE DATA
Device
NCP1596/
NCP1596A
VOUT
Inductor Model
Inductor (L1)
Diode (D1)
CIN (C1)
COUT (C2)
R1
R2
3.3 V
CDC5D23 3R3 (1 A)
CDRH6D38 3R3 (1.5 A)
3.3 mH
MBRA210LT3G
22 mF
22 mF x 2
22 mF
22 mF x 2
31 k
10 k
2.5 V
CDC5D23 3R3 (1 A)
CDRH6D38 3R3 (1.5 A)
3.3 mH
MBRA210LT3G
22 mF
22 mF x 2
22 mF
22 mF x 2
21 k
10 k
1.5 V
CDC5D23 3R3 (1 A)
CDRH6D38 3R3 (1.5 A)
3.3 mH
MBRA210LT3G
22 mF
22 mF x 2
22 mF
22 mF x 2
8k
10 k
1.2 V
CDC5D23 3R3 (1 A)
CDRH6D38 3R3 (1.5 A)
3.3 mH
MBRA210LT3G
22 mF
22 mF x 2
22 mF
22 mF x 2
5k
10 k
http://onsemi.com
4
NCP1596, NCP1596A
3.8 V
3.5 V
VIN
TIME 1 ms/div
VOUT
1 ms
EN
NC
1.8 V
0.4 V
TIME 1 ms/div
Figure 3. Timing Diagram
Power up the
device
VCC > 3 V
Enable the
internal Vref
NO
VCC > UVLO
YES
YES
Enable
Oscillator,
OTA and
driver
Ramp up
Soft start
(1 ms)
YES
Disable the
Oscillator,
OTA and driver
Temperature
<
130 deg
YES
Current Limit
> 2.5 A
VCC
<
UVLO
Temperature
>
160 deg
Normal
Operation
Figure 4. State Diagram
http://onsemi.com
5
YES
NO
NCP1596, NCP1596A
0.5
806
VFB, FB INPUT THRESHOLD (V)
RDS(on), SWITCH ON RESISTANCE (W)
TYPICAL OPERATING CHARACTERISTICS
0.4
0.3
0.2
0.1
0.0
−40
0
25
800
798
796
Figure 5. Switch ON Resistance vs.
Temperature
Figure 6. Feedback Input Threshold vs.
Temperature
1.52
1.50
1.48
1.46
0
25
85
3.0
2.5
2.0
1.5
1.0
0.5
−40
0
25
85
TA, AMBIENT TEMPERATURE (°C)
ICC+_SD, SHUTDOWN QUIESCENT CURRENT (mA)
Figure 7. Switching Frequency vs.
Temperature
550
530
510
490
470
0
85
3.5
TA, AMBIENT TEMPERATURE (°C)
ICC, QUIESCENT CURRENT INTO VCC (mA)
25
TA, AMBIENT TEMPERATURE (°C)
1.54
450
−40
0
TA, AMBIENT TEMPERATURE (°C)
ILIM, MAIN P−FET CURRENT LIMIT (V)
FOSC, SWITCH FREQUENCY (MHz)
802
794
−40
85
1.56
1.44
−40
804
25
85
TA, AMBIENT TEMPERATURE (°C)
Figure 8. Main P−FET Current Limit vs.
Temperature
500
450
400
350
300
250
−40
Figure 9. Quiescent Current Into VCC vs.
Temperature
0
25
TA, AMBIENT TEMPERATURE (°C)
Figure 10. Shutdown Quiescent Current vs.
Temperature
http://onsemi.com
6
85
1.5
100
1.0
90
OUTPUT EFFICIENCY (%)
DVOUT, OUTPUT VOLTAGE CHANGE (%)
NCP1596, NCP1596A
0.5
VIN = 5.0 V
0.0
VIN = 4.0 V
−0.5
VOUT = 3.3 V
L = 3.3 mH
CIN = 22 mF
COUT = 22 mF
−1.0
−1.5
1
10
100
1000
VIN = 5.0 V
80
70
60
50
40
30
10
10000
VIN = 4.0 V
VOUT = 3.3 V
L = 3.3 mH
CIN = 22 mF
COUT = 22 mF
100
OUTPUT CURRENT
1.5
100
1.0
90
0.5
VIN = 5.0 V
VIN = 4.0 V
−0.5
VOUT = 1.8 V
L = 3.3 mH
CIN = 22 mF
COUT = 22 mF
−1.0
−1.5
1
10
100
1000
80
VIN = 5.0 V
70
60
50
40
30
10
10000
VIN = 4.0 V
VOUT = 1.8 V
L = 3.3 mH
CIN = 22 mF
COUT = 22 mF
100
OUTPUT CURRENT
1.0
90
OUTPUT EFFICIENCY (%)
DVOUT, OUTPUT VOLTAGE CHANGE (%)
100
0.5
VIN = 5.0 V
0.0
−1.5
VIN = 4.0 V
VOUT = 1.2 V
L = 3.3 mH
CIN = 22 mF
COUT = 22 mF
1
10
100
10000
Figure 14. Efficiency vs. Output Current
1.5
−1.0
1000
OUTPUT CURRENT
Figure 13. Output Voltage Change vs.
Output Current
−0.5
10000
Figure 12. Efficiency vs. Output Current
OUTPUT EFFICIENCY (%)
DVOUT, OUTPUT VOLTAGE CHANGE (%)
Figure 11. Output Voltage Change vs. Output
Current
0.0
1000
OUTPUT CURRENT
1000
10000
VIN = 4.0 V
80
VIN = 5.0 V
70
60
50
40
30
10
OUTPUT CURRENT
VOUT = 1.2 V
L = 3.3 mH
CIN = 22 mF
COUT = 22 mF
100
1000
OUTPUT CURRENT
Figure 16. Output Voltage Change vs.
Output Current
Figure 15. Efficiency vs. Output Current
http://onsemi.com
7
10000
NCP1596, NCP1596A
(VIN = 5 V, ILOAD = 10 mA, L = 3.3 mH, COUT = 20 mF)
Upper Trace: Output Ripple Voltage, 20 mV/div
Middle Trace: LX Pin Switching Waveform, 5 V/div
Lower Trace: Inductor Current Waveform, 500 mA/div
Time Base: 500 ns/div
(VIN = 5 V, ILOAD = 500 mA, L = 3.3 mH, COUT = 20 mF)
Upper Trace: Output Ripple Voltage, 20 mV/div
Middle Trace: LX Pin Switching Waveform, 5 V/div
Lower Trace: Inductor Current Waveform, 500 mA/div
Time Base: 200 ns/div
Figure 17. DCM Switching Waveform for
VOUT = 3.3 V
Figure 18. CCM Switching Waveform for
VOUT = 3.3 V
(VIN = 5 V, ILOAD = 10 mA, L = 3.3 mH, COUT = 20 mF)
Upper Trace: Output Ripple Voltage, 20 mV/div
Middle Trace: LX Pin Switching Waveform, 5 V/div
Lower Trace: Inductor Current Waveform, 500 mA/div
Time Base: 2 ms/div
(VIN = 5 V, ILOAD = 500 mA, L = 3.3 mH, COUT = 20 mF)
Upper Trace: Output Ripple Voltage, 20 mV/div
Middle Trace: LX Pin Switching Waveform, 5 V/div
Lower Trace: Inductor Current Waveform, 500 mA/div
Time Base: 200 ns/div
Figure 19. DCM Switching Waveform for
VOUT = 1.2 V
Figure 20. CCM Switching Waveform for
VOUT = 1.2 V
(VIN = 5 V, ILOAD = 10 mA, L = 3.3 mH, COUT = 20 mFx2)
Upper Trace: Input Voltage, 1 V/div
Lower Trace: Output Voltage, 1 V/div
Time Base: 500 ms/div
(VIN = 5 V, ILOAD = 10 mA, L = 3.3 mH, COUT = 20 mFx2)
Upper Trace: Input Voltage, 1 V/div
Lower Trace: Output Voltage, 500 mV/div
Time Base: 500 ms/div
Figure 21. Soft−Start Waveforms for VOUT = 3.3 V
Figure 22. Soft−Start Waveforms for VOUT = 1.2 V
http://onsemi.com
8
NCP1596, NCP1596A
(VIN = 5 V, L = 3.3 mH, COUT = 10 mFx2)
Upper Trace: Output Dynamic Voltage, 100 mV/div
Lower Trace: Output Current, 200 mA/div
Time Base: 20 ns/div
(VIN = 5 V, L = 3.3 mH, COUT = 10 mFx2)
Upper Trace: Output Dynamic Voltage, 100 mV/div
Lower Trace: Output Current, 200 mA/div
Time Base: 20 ns/div
Figure 23. Load Regulation for VOUT = 3.3 V
Figure 24. Load Regulation for VOUT = 3.3 V
(VIN = 5 V, L = 3.3 H, COUT = 10 mFx2)
Upper Trace: Output Dynamic Voltage, 50 mV/div
Lower Trace: Output Current, 200 mA/div
Time Base: 10 ns/div
(VIN = 5 V, L = 3.3 H, COUT = 10 mF x 2)
Upper Trace: Output Dynamic Voltage, 50 mV/div
Lower Trace: Output Current, 200 mA/div
Time Base: 10 ns/div
Figure 25. Load Regulation for VOUT = 1.2 V
Figure 26. Load Regulation for VOUT = 1.2 V
http://onsemi.com
9
NCP1596, NCP1596A
DETAILED OPERATING DESCRIPTION
Introduction
inside NCP1596 to overcome the potential instability. Slope
compensation consists of a ramp signal generated by the
synchronization block and adding this to the inductor
current signal. The summed signal is then applied to the
PWM comparator.
The NCP1596 is a current−mode buck converter with
switching frequency at 1.5 MHz. High operation frequency
can reduce the capacitor value and PCB area. Also, more
features are built in this converter.
1. Internal 1 ms soft−start to avoid inrush current at
startup.
2. Internal cycle by cycle current limit provides an
output short circuit protection.
3. Internal compensation. No external compensation
components are necessary.
4. Thermal shutdown protects the devices from over
heat.
5. 100% duty cycle allowed. Speed up transient load
response.
The upper feature can provide more cost effective
solutions to applications. A simple function block diagram
and timing diagram are shown in Figure 1 and Figure 2.
Thermal Shutdown
Internal Thermal Shutdown circuitry is provided to
protect the integrated circuit in the event when maximum
junction temperature is exceeded. When activated, typically
at 180°C, the shutdown signal will disable the P−channel
switch. The thermal shutdown circuit is designed with 30°C
of hysteresis. This means that the switching will not start
until the die temperature drops by this amount. This feature
is provided to prevent catastrophic failures from accidental
device overheating. It is not intended as a substitute for
proper heat sinking. NCP1596 is contained in the
thermally enhanced QFN package.
Under Voltage Lockout (UVLO)
Soft−Start and Current Limit
UVLO function is used to ensure the logic level correctly
when input voltage is very low. In NCP1596, the UVLO
level is set to 3.5 V. If the input voltage is less than 3.5 V, the
converter will shutdown itself automatically.
A soft start circuit is internally implemented to reduce the
in−rush current during startup. This helps to reduce the
output voltage over−shoot.
The current limit is set to allow peak switch current in
excess of 2 A. The intended output current of the system is
1.5 A. The ripple current is calculated to be approximately
350 mA with a 3.3 mH inductor. Therefore, the peak current
at 1.5 A output will be approximately 1.7 Amps. A 2.5 Amp
set point will allow for transient currents during load step.
The current limit circuit is implemented as a cycle−by−cycle
current limit. Each on−cycle is treated as a separate situation.
Current limiting is implemented by monitoring the
P−channel switch current buildup during conduction with a
current limit comparator. The output of the current limit
comparator resets the PWM latch, immediately terminating
the current cycle. When output loading is short circuit,
device will auto restart with soft start.
Low Power Shutdown Mode (EN)
NCP1596A can be disabled whenever the EN pin is tied
to ground. During the shutdown mode, the internal
reference, oscillator and driver control circuits will be turn
off, the device only consume 1 mA typically and output
voltage will be discharge to zero by the external resistor
divider. EN pin has an internal pull−up current source, which
typical value is 500 nA.
Power Saving Pulse−Frequency−Modulation (PFM)
Control Scheme
While the converter loading decreases, the converter
enters the Discontinues−conduction−mode (DCM)
operation. In DCM operation, the on−time (Ton) of the
integrated switch for each switching cycle will decrease
when the output current decreases. In order to maintain a
high converter efficiency at light load condition. A
minimum Ton is set to 70 ns. It can make sure a minimum
fixed power send to output. To avoid a higher switch loss
occurs when without loading apply. This control scheme can
reduce the switching loss at light load and improve the
conversion efficiency.
Error Amplifier and Slope Compensation
A fully internal compensated error amplifier is provided
inside NCP1596. No external circuitry is needed to stabilize
the device. The error amplifier provides an error signal to the
PWM comparator by comparing the feedback voltage
(800 mV) with internal voltage reference of 1.2 V.
Current mode converter can exhibit instability at duty
cycles over 50%. A slope compensation circuit is provided
http://onsemi.com
10
NCP1596, NCP1596A
APPLICATION INFORMATION
Output Voltage Selection
ripple current, input voltage, output voltage, output current
and operation frequency, the inductor value is given by:
The output voltage is programmed through an external
resistor divider connect from VOUT to FB then to GND.
For internal compensation and noise immunity, the
resistor from FB to GND should be in 10 k to 20 k ranges.
The relationship between the output voltage and feedback
resistor is given by:
V OUT + V FB
ǒ1 ) R1Ǔ
D IL +
ǒ1 * VV Ǔ
OUT
F SW
(eq. 2)
IN
DIL : peak to peak inductor ripple current
L: inductor value
FSW: switching frequency
After selected a suitable value of the inductor, it should be
check out the inductor saturation current. The saturation
current of the inductor should be higher than the maximum
load plus the ripple current.
(eq. 1)
R2
V OUT
L
VOUT: Output voltage
VFB: Feedback Voltage
R1: Feedback resistor from VOUT to FB.
R2: Feedback resistor from FB to GND.
D IL(MAX) + D IOUT(MAX) )
Input Capacitor Selection
DIL(MAX)
DIOUT(MAX)
In the PWM buck converter, the input current is pulsating
current with switching noise. Therefore, a bypass input
capacitor must choose for reduce the peak current drawn
from the power supply. For NCP1596, low ESR ceramic
capacitor of 10 mF should be used for most of cases. Also,
the input capacitor should be placed as close as possible to
the VCCA pin for effective bypass the supply noise.
D IL
(eq. 3)
2
: Maximum inductor current
: Maximum output current
Output Capacitor Selection
Output capacitor value is based on the target output ripple
voltage. For NCP1596, the output capacitor is required a
ceramic capacitors with low ESR value. Assume buck
converter duty cycle is 50%. The output ripple voltage in
PWM mode is given by:
Inductor Selection
The inductor parameters are including three items, which
are DC resistance, inductor value and saturation current.
Inductor DC resistance will effect the convector overall
efficiency, low DC resistor value can provide a higher
efficiency. Thus, inductor value are depend on the inductor
D VOUT [ D IL
ǒ4
1
FSW
C OUT
Ǔ
) ESR (eq. 4)
In general, value of ceramic capacitor using 20 mF should
be a good choice.
ORDERING INFORMATION
Device
Package
Shipping†
NCP1596MNTWG
DFN−6
(Pb−Free)
3000 / Tape & Reel
NCP1596AMNTWG
DFN−6
(Pb−Free)
3000 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
11
NCP1596, NCP1596A
PACKAGE DIMENSIONS
DFN6 3*3 MM, 0.95 PITCH
CASE 506AH−01
ISSUE O
A
D
B
ÇÇÇÇ
ÇÇÇÇ
ÇÇÇÇ
ÇÇÇÇ
PIN 1
REFERENCE
2X
NOTES:
1. DIMENSIONS AND TOLERANCING PER ASME
Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMESNION b APPLIES TO PLATED TERMINAL
AND IS MEASURED BETWEEN 0.25 AND 0.30
MM FROM TERMINAL.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
E
DIM
A
A1
A3
b
D
D2
E
E2
e
K
L
0.15 C
2X
0.15 C
TOP VIEW
0.10 C
A
6X
0.08 C
(A3)
SIDE VIEW
6X
SOLDERING FOOTPRINT*
0.450
0.0177
D2
L
e
1
6X
C
A1
SEATING
PLANE
MILLIMETERS
MIN
NOM MAX
0.80
0.90
1.00
0.00
0.03
0.05
0.20 REF
0.35
0.40
0.45
3.00 BSC
2.40
2.50
2.60
3.00 BSC
1.50
1.60
1.70
0.95 BSC
0.21
−−−
−−−
0.30
0.40
0.50
4X
0.950
0.0374
3
E2
K
1.700
0.0685
3.31
0.130
6
4
6X
b
(NOTE 3)
0.10 C A B
BOTTOM VIEW
0.05 C
0.63
0.025
2.60
0.1023
SCALE 10:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer
purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
12
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCP1596/D
Similar pages