MMD IM811B Mems oscillator, ultra performance, high freq., lvcmos/ hcmos compatible, 80.0 mhz to 220.0mhz Datasheet

MEMS Oscillator, Ultra Performance, High Freq., LVCMOS/ HCMOS Compatible, 80.0 MHz to 220.0MHz
Features:
Typical Applications:











MEMS Technology
Direct pin to pin drop-in replacement for industry-standard packages
Ultra-low phase jitter: 0.5 pSec (12 kHz to 20 MHz)
LVCMOS/HCMOS Compatible Output
Industry-standard package 2.5 x 2.0, 3.2 x 2.5, and 5.0 x 3.2 mm x mm
Pb-free, RoHS and REACH compliant
Fast delivery times
IM811 Series
Fibre Channel
Server and Storage
GPON, EPON
100M / 1G /10G Ethernet
Electrical Specifications:
Frequency Range
Frequency Stability
80.000 MHz to 220.000MHz
See Part Number Guide
Operating Temperature
Supply Voltage (Vdd) ±10%
Current Consumption
See Part Number Guide
See Part Number Guide
34 mA typ./ 36 mA max
30 mA typ./ 33 mA max
31 mA max
30 mA max
70 µA max
10 µA max
OE Disable Current
Standby Current
LVCMOS/HCMOS
45%/55%
40%/60%
1.2 nSec typ./ 2.0 nSec max
90% of Vdd min
10% of Vdd max
70% of Vdd min
Waveform Output
Symmetry
Rise / Fall Time
Logic “1”
Logic “0”
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
30% of Vdd max
100 kΩ typ./ 250 kΩ max
2.0 MΩ min
Startup Time
OE Enable/Disable Time
Resume Time
RMS Period Jitter
7 mSec typ./ 10 mSec max
115 nSec max
10 mSec max
1.5 pSec typ./ 2.0 pSec max
2.0 pSec typ./ 3.0 pSec max
0.5 pSec typ./ 1.0 pSec max
±1.5 ppm
±5.0 ppm
RMS Phase Jitter (random)
First year Aging
10-years Aging
Inclusive of Initial Tolerance, Operating Temperature Range, Load, and
Voltage
No load condition, f = 100 MHz, Vdd = +2.5 V, +2.8 V or +3.3 V
No load condition, f = 100 MHz, Vdd = +1.8V
Vdd = +2.5 V, +2.8 V or +3.3 V, OE = GND
Vdd = +1.8 V, OE = GND
Vdd = +2.5 V, +2.8 V or +3.3 V, ST = GND
Vdd = +1.8 V, ST = GND
F = less than 165 MHz all Vdds
F = greater than 165 MHz all Vdds
15 pF Load, 10% to 90% of Vdd
Pin 1, OE or ST
Pin 1, OE or ST
Pin 1, OE logic high or logic low, or ST logic high
Pin 1, ST logic low
Measured from the time Vdd reaches its rated minimum values
F= 80 MHz, For other frequencies, T_oe = 100 nSec = 3 cycles
In standby mode, measured from the time ST pin crosses 50% threshold.
F = 156.25 MHz, Vdd = +2.5 V,+2.8 V or +3.3 V
F = 156.25 MHz, Vdd = +1.8 V
F = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz
At +25ºC ±2ºC
At +25ºC ±2ºC
Notes:

All min and max limits are specified over temperature and rated operating voltage with 15pF output unless otherwise stated.

Typical values are at +25ºC and nominal supply voltage.
Absolute Maximum Limits
Storage Temperature
Supply Voltage (Vdd)
Electrostatic Discharge
Solder Temperature (follow standard Pb free soldering guidelines)
Junction Temperature
-65ºC to +150ºC
-0.5 VDC to 4.0 VDC
2000 V max
260ºC max
150ºC max
ILSI America Phone 775-851-8880 ● Fax 775-851-8882 ●email: [email protected] ●
www.ilsiamerica.com
Specifications subject to change without notice
Rev: 01/30/16_A
Page 1 of 7
MEMS Oscillator, Ultra Performance, High Freq., LVCMOS/ HCMOS Compatible, 80.0 MHz to 220.0MHz
IM811 Series
Ordering Information:
Part Number Guide
Packages
IM811B – 5.0 x 3.2
IM811C – 3.2 x 2.5
IM811D – 2.5 x 2.0
Input Voltage
1 = +1.8 V
6 = +2.5 V
2 = +2.7 V
7 = +3.0 V
3 = +3.3 V
Operating
Temperature
1 = 0ºC to +70ºC
2 = -40ºC to +85ºC
3 = -20ºC to +70ºC
Output Drive
Strength
- = Default
Stability
(ppm)
E = ±10
F = ±20
A = ±25
B = ±50
Select Function
Frequency
H = Tri-state
S = Standby
-
Frequency
Sample Part Number: IM811C-31-FS-100.0000MHz
This 100.0000 MHz oscillator in a 3.2 x 2.5 package with stability ±20 ppm from 0ºC to +70ºC using a supply voltage of +3.3 V. With Pin 1 function as
Standby. Output Drive Strength is only set to the default level.
Sample Part Number: IM811D-13-AH-125.0000MHz
This 125.0000 MHz oscillator in a 2.5 x 2.0 package with stability ±25 ppm from -20ºC to +70ºC using a supply voltage of +1.8 V. With Pin 1 function as
Tri-state. Output Drive Strength is only set to the default level.
Notes:

Not all options are available at all frequencies and temperatures ranges.

Please consult with sales department for any other parameters or options.

Oscillator specification subject to change without notice.
Phase Noise:
Figure 1: Phase Noise, 156.25 MHz, +3.3 V LVCMOS Output
ILSI America Phone 775-851-8880 ● Fax 775-851-8882 ●email: [email protected] ●
www.ilsiamerica.com
Specifications subject to change without notice
Rev: 01/30/16_A
Page 2 of 7
MEMS Oscillator, Ultra Performance, High Freq., LVCMOS/ HCMOS Compatible, 80.0 MHz to 220.0MHz
IM811 Series
Performance Plots
Figure 2: Idd vs Frequency
Figure 3: RMS Period vs Frequency
Figure 4: Duty Cycle vs Frequency
Figure 5: RMS Phase Jitter vs Frequency
Figure 6: Idd vs Temperature, 100 MHz Output
Figure 7: Rise Time vs Temperature, 100 MHz Output
Note:
All plots are measured with 15pF load at room temperature, unless otherwise stated.
ILSI America Phone 775-851-8880 ● Fax 775-851-8882 ●email: [email protected] ●
www.ilsiamerica.com
Specifications subject to change without notice
Rev: 01/30/16_A
Page 3 of 7
MEMS Oscillator, Ultra Performance, High Freq., LVCMOS/ HCMOS Compatible, 80.0 MHz to 220.0MHz
IM811 Series
Waveform
Test Circuit
Environmental Specifications:
Environmental Compliance
Parameter
Condition/Test Method
MIL-STD-883F, Method 2002
MIL-STD-883F, Method 2007
JESD22, Method A104
MIL-STD-883F, Method 2003
MSL Level 1 at +260ºC
Mechanical Shock
Mechanical Vibration
Temperature Cycle
Solderability
Moisture Sensitivity Level
Pb Free Solder Reflow Profile
Units are backward compatible with +240ºC reflow processes
Ts max to TL (Ramp-up Rate)
Preheat
Temperature min (Ts min)
Temperature typ (Ts typ)
Temperature max (Ts max)
Time (Ts)
Ramp-up Tate (TL to Tp
Time Maintained Above
Temperature (TL)
Time (TL)
Peak Temperature (Tp)
Time within 5ºC to Peak
Temperature (Tp)
Ramp-down Rate
Tune 25ºC to Peak
Temperature
Moisture Sensitivity Level
(MSL)
ILSI America Phone 775-851-8880 ● Fax 775-851-8882 ●email: [email protected] ●
www.ilsiamerica.com
Specifications subject to change without notice
3ºC / second max
150ºC
175ºC
200ºC
60 to180 seconds
3ºC / second max
217ºC
60 to 150 seconds
260ºC max for seconds
20 to 40 seconds
6ºC / second max
8 minute max
Level 1
Rev: 01/30/16_A
Page 4 of 7
MEMS Oscillator, Ultra Performance, High Freq., LVCMOS/ HCMOS Compatible, 80.0 MHz to 220.0MHz
IM811 Series
Pin Functionally
Pin
Symbol
OE
Tri-state
ST
Standby
1
Pin Description
Functionality
High or Open = specified frequency output
Low = Output is high impedance, only output is disabled.
High or Open = specified frequency output.
Low = Output is low. Device goes to sleep mode. Supply current
reduces to standby current.
Electrical ground
Oscillator output
Power supply voltage
2
GND
Power
3
Out
Output
4
Vdd
Power
Notes:
1. In OE or ST mode, a pull-up resistor of 10.0 kΩ or less is recommended if Pin 1 is not externally
driven
2. A capacitor of value 0.1 µF or higher between Pin 4 (Vdd) and Pin 1 (GND) is required.
Pin Assignments
OE
1
ST
4
Vdd
3
OUT
Top View
GND 2
Timing Diagrams:
Figure 8: Startup Timing (OE/
Mode)
Figure 9: Standby Resume Timing (
Mode Only)
Figure 10: OE Enable Timing (OE Mode Only)
Figure 11: OE Disable Timing (OE Mode Only)
ILSI America Phone 775-851-8880 ● Fax 775-851-8882 ●email: [email protected] ●
www.ilsiamerica.com
Specifications subject to change without notice
Rev: 01/30/16_A
Page 5 of 7
MEMS Oscillator, Ultra Performance, High Freq., LVCMOS/ HCMOS Compatible, 80.0 MHz to 220.0MHz
IM811 Series
Mechanical Details:
Package Dimensions and Suggest Land Pattern
Option D: 2.70 x 2.40 Package (100% compatible with 2.50 x 2.00)
1.00
2.50 ±0.05
1.90
3
Marking
Suggested Land Pattern
2.40 ±0.05 1.10
4
Bottom View
2
0.80 max
1
0.5
1.50
1.0
0.75
1.1
Option C: 3.20 x 2.50 Package
Suggested Land Pattern
3.20 ±0.05
2.1
2.20
3
Marking
2.50±0.05
0.90
4
Bottom View
1
2
0.80 max
0.7
1.90
1.2
0.9
1.4
Opton B: 5.00 x 3.20 Package
Suggested Land Pattern
5.00 ±0.05
2.39
3
Marking
3.20 ±0.05 0.80
4
Bottom View
2
0.80 max
2.54
1
1.1
2.20
1.6
1.15
1.5
Marking
Line 1 = XXXXX (Lot Code)
Dot to denote Pin 1 location
Package Information
Leadframe: C194
Plating: NiPdAu
ILSI America Phone 775-851-8880 ● Fax 775-851-8882 ●email: [email protected] ●
www.ilsiamerica.com
Specifications subject to change without notice
Rev: 01/30/16_A
Page 6 of 7
MEMS Oscillator, Ultra Performance, High Freq., LVCMOS/ HCMOS Compatible, 80.0 MHz to 220.0MHz
IM811 Series
Tape and Reel Dimensions
PITCH
Q1 Q2
REEL DIA
TAPE
WIDTH
Q3 Q4
DIRECTION OF FEED
REF: EIA-481-E
Part
Number
Size
Pitch
Tape
Width
Pin
Orient.
IM811B
5.0 x 3.2
8.0 ± 0.1
12.3 max
Q1
IM811C
IM811D
3.2 x 2.5
2.5 x 2.0
4.0 ± 0.1
4.0 ± 0.1
8.3 max
8.3 max
Q1
Q1
Reel
Dia.
180
330
180
180
Count
1000
3000
3000
3000
Notes:

All dimensions are in mm.

Do not scale drawings.
PROPRIETARY AND CONFIDENTIAL
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION, AND SUCH INFORMATION MAY NOT BE DISCLOSED TO OTHERS FOR ANY
PURPOSE NOR USED FOR MANUFACTURING PURPOSES WITHOUT WRITTEN PERMISSION FROM ILSI America.
ILSI America Phone 775-851-8880 ● Fax 775-851-8882 ●email: [email protected] ●
www.ilsiamerica.com
Specifications subject to change without notice
Rev: 01/30/16_A
Page 7 of 7
Similar pages