Finisar FTLX3612M328 40km multi-rate dwdm xfp optical transceiver Datasheet

Finisar
Product Specification
~40km Multi-Rate DWDM XFP Optical Transceiver
FTLX3612M3xx
PRODUCT FEATURES
•
Supports 9.95Gb/s to 11.3Gb/s
bit rates
•
100GHz channel spacing on the
ITU C-band
•
Hot-pluggable XFP footprint
•
RoHS-6 Compliant (lead-free)
•
Temperature-stabilized 1550nm
EML transmitter
•
Supports -300ps/nm to +800ps/nm
APPLICATIONS
•
3.3V and 5V power supplies
required
•
•
Duplex LC connector
•
Power dissipation < 3.5W
•
SONET OC-192 IR-2
SDH STM S-64.2b
SONET OC-192 IR-3
SDH STM S-64.3b
ITU-T G.709
Built-in digital diagnostic functions
•
•
Commercial temperature range:
0°C to 70°C
10GBASE-ER/EW
10GBASE-ER/EW + FEC
•
40km 10G Fibre Channel
40km 10G Fibre Channel + FEC
•
Reference clock not required
Finisar’s 40km DWDM FTLX3612M3xx Small Form Factor 10Gb/s XFP transceivers
comply with the current XFP Multi-Source Agreement (MSA) Specification1. They also
comply with SONET OC-192 IR-2, OC-192 IR-3, SDH STM S-64.2b, STM S-64.3b as
well as with 10-Gigabit Ethernet 10GBASE-ER/EW per IEEE 802.3ae and 40km 10G
Fibre Channel applications. Digital diagnostics functions are available via a 2-wire serial
interface, as specified in the XFP MSA. The transceiver is RoHS compliant and lead free
per Directive 2002/95/EC3, and Finisar Application Note AN-20384.
PRODUCT SELECTION
FTLX3612M3xx
xx: 100GHz ITU Grid wavelength (see next page)
© Finisar Corporation 11-January-2011
Rev B1
Page 1
FTLX3612M3xx 40km DWDM XFP –Product Specification – January 2011
Finisar
Channel #
Product Code
Frequency (THz)
Center Wavelength (nm)
15*
FTLX3612M315
191.5
1565.50
16*
FTLX3612M316
191.6
1564.68
17*
FTLX3612M317
191.7
1563.86
18*
FTLX3612M318
191.8
1563.05
19
FTLX3612M319
191.9
1562.23
20
FTLX3612M320
192.0
1561.42
21
FTLX3612M321
192.1
1560.61
22
FTLX3612M322
192.2
1559.79
23
FTLX3612M323
192.3
1558.98
24
FTLX3612M324
192.4
1558.17
25
FTLX3612M325
192.5
1557.36
26
FTLX3612M326
192.6
1556.55
27
FTLX3612M327
192.7
1555.75
28
FTLX3612M328
192.8
1554.94
29
FTLX3612M329
192.9
1554.13
30
FTLX3612M330
193.0
1553.33
31
FTLX3612M331
193.1
1552.52
32
FTLX3612M332
193.2
1551.72
33
FTLX3612M333
193.3
1550.92
34
FTLX3612M334
193.4
1550.12
35
FTLX3612M335
193.5
1549.32
36
FTLX3612M336
193.6
1548.51
37
FTLX3612M337
193.7
1547.72
38
FTLX3612M338
193.8
1546.92
39
FTLX3612M339
193.9
1546.12
40
FTLX3612M340
194.0
1545.32
41
FTLX3612M341
194.1
1544.53
42
FTLX3612M342
194.2
1543.73
43
FTLX3612M343
194.3
1542.94
44
FTLX3612M344
194.4
1542.14
45
FTLX3612M345
194.5
1541.35
46
FTLX3612M346
194.6
1540.56
47
FTLX3612M347
194.7
1539.77
48
FTLX3612M348
194.8
1538.98
49
FTLX3612M349
194.9
1538.19
50
FTLX3612M350
195.0
1537.40
51
FTLX3612M351
195.1
1536.61
52
FTLX3612M352
195.2
1535.82
53
FTLX3612M353
195.3
1535.04
54
FTLX3612M354
195.4
1534.25
55
FTLX3612M355
195.5
1533.47
56
FTLX3612M356
195.6
1532.68
57
FTLX3612M357
195.7
1531.90
58
FTLX3612M358
195.8
1531.12
59
FTLX3612M359
195.9
1530.33
60
FTLX3612M360
196.0
1529.55
61*
FTLX3612M361
196.1
1528.77
Note* Æ Please contact your Finisar representative for non-standard channels indicated with an “*”.
© Finisar Corporation 11-January-2011
Rev B1
Page 2
FTLX3612M3xx 40km DWDM XFP –Product Specification – January 2011
I.
Finisar
Pin Descriptions
Pin
1
2
3
Logic
LVTTL-I
4
LVTTL-O
5
6
7
8
9
10
11
LVTTL-I
Symbol
GND
VEE5
Mod-Desel
Interrupt
TX_DIS
VCC5
GND
VCC3
VCC3
SCL
SDA
12
LVTTL-I
LVTTLI/O
LVTTL-O
Mod_Abs
13
LVTTL-O
Mod_NR
14
15
16
17
18
19
20
21
LVTTL-O
LVTTL-I
RX_LOS
GND
GND
RDRD+
GND
VCC2
P_Down/RST
22
23
24
PECL-I
VCC2
GND
RefCLK+
25
PECL-I
RefCLK-
26
27
28
29
30
CML-O
CML-O
CML-I
CML-I
GND
GND
TDTD+
GND
Name/Description
Module Ground
Optional –5.2 Power Supply – Not required
Module De-select; When held low allows the module to
respond to 2-wire serial interface commands
Interrupt (bar); Indicates presence of an important condition
which can be read over the serial 2-wire interface
Transmitter Disable; Transmitter laser source turned off
+5 Power Supply
Module Ground
+3.3V Power Supply
+3.3V Power Supply
Serial 2-wire interface clock
Serial 2-wire interface data line
Ref.
1
Module Absent; Indicates module is not present. Grounded
in the module.
Module Not Ready; Finisar defines it as a logical OR
between RX_LOS and Loss of Lock in TX/RX.
Receiver Loss of Signal indicator
Module Ground
Module Ground
Receiver inverted data output
Receiver non-inverted data output
Module Ground
+1.8V Power Supply – Not Required
Power Down; When high, places the module in the low
power stand-by mode and on the falling edge of P_Down
initiates a module reset
Reset; The falling edge initiates a complete reset of the
module including the 2-wire serial interface, equivalent to a
power cycle.
+1.8V Power Supply – Not Required
Module Ground
Reference Clock non-inverted input, AC coupled on the
host board – Not required
Reference Clock inverted input, AC coupled on the host
board – Not required
Module Ground
Module Ground
Transmitter inverted data input
Transmitter non-inverted data input
Module Ground
2
2
1
2
2
2
2
1
1
1
1
1
1
1
Notes:
1. Module circuit ground is isolated from module chassis ground within the module.
2. Open collector; should be pulled up with 4.7k – 10kohms on host board to a voltage between 3.15V
and 3.6V.
© Finisar Corporation 11-January-2011
Rev B1
Page 3
Finisar
FTLX3612M3xx 40km DWDM XFP –Product Specification – January 2011
Diagram of Host Board Connector Block Pin Numbers and Names
II.
Absolute Maximum Ratings
Parameter
Maximum Supply Voltage 1
Maximum Supply Voltage 2
Storage Temperature
Case Operating Temperature
© Finisar Corporation 11-January-2011
Symbol
Vcc3
Vcc5
TS
TOP
Rev B1
Min
-0.5
-0.5
-40
-5
Typ
Max
4.0
6.0
85
70
Unit
V
V
°C
°C
Ref.
Page 4
Finisar
FTLX3612M3xx 40km DWDM XFP –Product Specification – January 2011
III.
Electrical Characteristics (TOP = -5 to 70 °C, VCC5 = 4.75 to 5.25 Volts)
Parameter
Main Supply Voltage
Supply Voltage #2
Supply Current – Vcc5 supply
Supply Current – Vcc3 supply
Module total power
Transmitter
Input differential impedance
Differential data input swing
Transmit Disable Voltage
Transmit Enable Voltage
Transmit Disable Assert Time
Receiver
Differential data output swing
Data output rise time
Data output fall time
LOS Fault
LOS Normal
Power Supply Rejection
Symbol
Vcc5
Vcc3
Icc5
Icc3
P
Rin
Vin,pp
VD
VEN
Vout,pp
tr
tf
VLOS fault
VLOS norm
PSR
Min
4.75
3.13
Typ
Max
5.25
3.45
350
750
3.5
Unit
V
V
mA
mA
W
2
820
Vcc
GND+ 0.8
10
Ω
mV
V
V
us
mV
ps
ps
V
V
4
5
5
6
6
7
100
120
2.0
GND
340
Vcc – 0.5
GND
650
850
38
38
VccHOST
GND+0.5
See Note 6 below
Ref.
1
3
Notes:
1. Maximum total power value is specified across the full temperature and voltage range.
2. After internal AC coupling.
3. Or open circuit.
4. Into 100 ohms differential termination.
5. 20 – 80 %
6. Loss Of Signal is open collector to be pulled up with a 4.7k – 10kohm resistor to 3.15 – 3.6V. Logic 0
indicates normal operation; logic 1 indicates no signal detected.
7. Per Section 2.7.1. in the XFP MSA Specification1.
© Finisar Corporation 11-January-2011
Rev B1
Page 5
Finisar
FTLX3612M3xx 40km DWDM XFP –Product Specification – January 2011
IV.
Optical Characteristics (TOP = -5 to 70°C, VCC5 = 4.75 to 5.25 Volts)
Please note that the Transmitter of the FTLX3612M3xx becomes operational within 5
seconds of power-up. This is due to the time required for the EML to reach its optimum
operating temperature.
Parameter
Transmitter
Output Opt. Pwr: 9/125 SMF
Optical Extinction Ratio
Optical Modulation Amplitude
Center Wavelength Spacing
Transmitter Center Wavelength – End
Of Life
Transmitter Center Wavelength –
Beginning Of Life
Transmitter Dispersion Penalty
(@ 800 ps/nm)
Sidemode Supression ratio
Tx Jitter (SONET) 20kHz-80MHz
Tx Jitter (SONET) 4MHz – 80MHz
Symbol
Min
POUT
ER
ΟΜΑ
-1
8.2
-2.1
Relative Intensity Noise
Receiver
Receiver Sensitivity @ 9.95Gb/s to
10.7Gb/s
Receiver Sensitivity @ 11.1Gb/s to
11.3Gb/s
Stressed Receiver Sensitivity (OMA)
@ 11.1Gb/s
Maximum Input Power
Optical Center Wavelength
Receiver Reflectance
Path penalty at 40km (up to 10.7Gb/s)
LOS De-Assert
LOS Assert
LOS Hysteresis
Typ
Max
Unit
Ref.
+2
1
X+100
dBm
dB
dBm
GHz
pm
X+25
pm
2
dB
0.3
0.1
dB
UI
UI
RIN
-130
dB/Hz
RSENS1
-16
dBm
RSENS2
-15
dBm
RSENS2
-11.3
dBm
λc
X-100
100
X
λc
X-25
X
TDP
SSRmin
Txj1
Txj2
PMAX
λC
Rrx
LOSD
LOSA
30
-1
1270
-28
0.5
1600
-27
2
-22
dBm
nm
dB
dB
dBm
dBm
dB
2
2
3
Notes:
1. Guaranteed minimum OMA for 9.9Gb/s - 11.3Gb/s.
2. GR-253-CORE Issue 4
3. Dispersion penalty is measured in loopback using 18 ps/(nm*km) fiber (SMF-28). Path penalty is 2dB
at 10.7Gb/s.
© Finisar Corporation 11-January-2011
Rev B1
Page 6
Finisar
FTLX3612M3xx 40km DWDM XFP –Product Specification – January 2011
V.
General Specifications
Parameter
Bit Rate
Bit Error Ratio
Max. Supported Link Length
Symbol
BR
BER
LMAX
Min
9.95
Typ
Max
11.3
10-12
40
Units
Gb/s
km
Ref.
1
2
1
Notes:
1. SONET OC-192 IR-2, OC-192 IR-3, 10GBASE-ER/EW, 10G Fibre Channel, ITU-T G.709,
10GBASE-ER/EW + FEC, 10G Fibre Channel + FEC
2. Tested with a 231 – 1 PRBS
VI.
Environmental Specifications
The FTLX3612M3xx transceiver has an operating case temperature range from 0°C to
+70°C.
Parameter
Case Operating Temperature
Storage Temperature
VII.
Symbol
Top
Tsto
Min
-5
-40
Typ
Max
70
85
Units
°C
°C
Ref.
Regulatory Compliance
Finisar XFP transceivers are Class 1 Laser Products. They are certified per the following
standards:
Feature
Agency
Standard
Laser Eye
Safety
Laser Eye
Safety
FDA/CDRH
CDRH 21 CFR 1040 and Laser Notice 50
TÜV
72101686
Electrical
Safety
Electrical
Safety
TÜV
EN 60825-1: 1994+A11:1996+A2:2001
IEC 60825-1: 1993+A1:1997+A2:2001
IEC 60825-2: 2000, Edition 2
EN 60950
CLASS 3862.07
CLASS 3862.87
2283290
UL/CSA
Certificate
Number
9210176-77
72101686
Copies of the referenced certificates are available at Finisar Corporation upon request.
© Finisar Corporation 11-January-2011
Rev B1
Page 7
FTLX3612M3xx 40km DWDM XFP –Product Specification – January 2011
Finisar
VIII. Digital Diagnostics Functions
As defined by the XFP MSA1, Finisar XFP transceivers provide digital diagnostic
functions via a 2-wire serial interface, which allows real-time access to the following
operating parameters:
•
•
•
•
•
Transceiver temperature
Laser bias current
Transmitted optical power
Received optical power
Transceiver supply voltage
It also provides a sophisticated system of alarm and warning flags, which may be used to
alert end-users when particular operating parameters are outside of a factory-set normal
range.
The operating and diagnostics information is monitored and reported by a Digital
Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed
through the 2-wire serial interface. When the serial protocol is activated, the serial clock
signal (SCL pin) is generated by the host. The positive edge clocks data into the XFP
transceiver into those segments of its memory map that are not write-protected. The
negative edge clocks data from the XFP transceiver. The serial data signal (SDA pin) is
bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to
mark the start and end of serial protocol activation. The memories are organized as a
series of 8-bit data words that can be addressed individually or sequentially. The 2-wire
serial interface provides sequential or random access to the 8 bit parameters, addressed
from 000h to the maximum address of the memory.
For more detailed information, including memory map definitions, please see the XFP
MSA documentation1.
© Finisar Corporation 11-January-2011
Rev B1
Page 8
FTLX3612M3xx 40km DWDM XFP –Product Specification – January 2011
IX.
Finisar
Mechanical Specifications
Finisar’s XFP transceivers are compliant with the dimensions defined by the XFP MultiSourcing Agreement (MSA).
77.95
22.15
18.35
13.30
8.50
LATCHED
1.95
16.00
UNLATCHED
20.85
R1.00
39.00
XFP Transceiver (dimensions are in mm)
© Finisar Corporation 11-January-2011
Rev B1
Page 9
FTLX3612M3xx 40km DWDM XFP –Product Specification – January 2011
X.
Finisar
PCB Layout and Bezel Recommendations
XFP Host Board Mechanical Layout (dimensions are in mm)
© Finisar Corporation 11-January-2011
Rev B1
Page 10
FTLX3612M3xx 40km DWDM XFP –Product Specification – January 2011
Finisar
XFP Detail Host Board Mechanical Layout (dimensions are in mm)
© Finisar Corporation 11-January-2011
Rev B1
Page 11
FTLX3612M3xx 40km DWDM XFP –Product Specification – January 2011
Finisar
XFP Recommended Bezel Design (dimensions are in mm)
© Finisar Corporation 11-January-2011
Rev B1
Page 12
FTLX3612M3xx 40km DWDM XFP –Product Specification – January 2011
Finisar
XI.
References
1.
10 Gigabit Small Form Factor Pluggable Module (XFP) Multi-Source Agreement
(MSA), Rev 4.5 – August 2005. Documentation is currently available at
http://www.xfpmsa.org/
2.
Application Note AN-2035: “Digital Diagnostic Monitoring Interface for XFP
Optical Transceivers” – Finisar Corporation, December 2003
3.
Directive 2002/95/EC of the European Council Parliament and of the Council,
“on the restriction of the use of certain hazardous substances in electrical and
electronic equipment”. January 27, 2003.
4.
“Application Note AN-2038: Finisar Implementation Of RoHS Compliant
Transceivers”, Finisar Corporation, January 21, 2005.
XII.
Revision History
Revision
Date
Description
A1
5/26/2010
•
Document created.
B1
1/11/2011
•
Removed Preliminary from datasheet
XIII. For More Information
Finisar Corporation
1389 Moffett Park Drive
Sunnyvale, CA 94089-1133
Tel. 1-408-548-1000
Fax 1-408-541-6138
[email protected]
www.finisar.com
© Finisar Corporation 11-January-2011
Rev B1
Page 13
Similar pages